Loading
Loading…
Loading…
Tender Value
₹3.9 Cr
EMD Value
₹7.9 L
Closing Date
1 Jun 2026, 3:30 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
DRM/WORKS
14 conditions · 2 needing a document upload
10.2 - Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees. N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, as provided at Page 41 of tender documents, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
10.1 Technical Eligibility Criteria: (a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b) (1)In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii)One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre- defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Non-submission of the Completion certificate issued by the Competent Authority shall result into summarily rejection of the offer.
Defination of Similar Work :- 3.1 - Any Civil Construction or repair work
27 conditions · 3 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions. (Ref: Rly. Bd. Letter No.2020/RS(G)/779/2/Pt.1 (E3322671) Dtd. 20.08.2024 and Public Procurement (Preference to Make in India), Order 2017 Revision and No.P-45021/2/2017-PP(BE-II)-Par (4) Vol.II Dtd. 19th July 2024, Government of India, Ministry of Commerce and Industry, Department for Promotion of Industry and Internal Trade (Public Procurement Section) amended time to time.
"The said suppliers of goods and/or services would be subject to GST Act and Rules as applicable from time to time. Tenderers are requested to submit their offers as per GST Tax regime. All the bidders/tenderers should ensure that they are GST compliant and their quoted tax structure/rates are as per GST Law"
Successful tenderers are required to submit the number of labour to be employed for this particular work. Also the list showing names, along with all other details, of male and female workers employed in this work, should be submitted to office, at the time of submitting performance guarantee and before executing contract agreement. They should also ensure that 1) The payment to the contract labour should be made through bank/cheque. 2) Identity Cards should be issued to all contract workers. 3) Necessary steps should be taken to deduct provident fund from the payment made to contract labour and ensure that the same is credited to their Provident Fund account. 4)Medical facilities from ESI should be ensured, if applicable.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tenderers are required to submit a copy of cancelled cheque in order to facilitate the payments regarding refund of EMD etc. in their proper accounts.
In addition to latest provisions of GCC, and all contents of tender documents, all other latest instructions of Railway Boards issued vide various letters received from time to time on concerned matters and related to tender, will also be applicable for the tenders as per necessity and tenderers have to co-operate with Railways and ensure the compliance
Indian Railways Standard General Conditions of Contract, April 2022 (GCC, April 2022) has been introduced and available on website with all correction slips issued up to date for inviting tender and same will be applicable for this tender. Advance Correction Slip No. 1, 2, 3, 4, 5, 6, 7, 8, 9, 10 and 11 to Indian Railways Standard General Conditions of Contract, April - 2022 circulated by the Railway Board vide letter No. 2022/CE-I/ CT/GCC-2022/Policy dated 14.07.2022, 13.12.2022, 26.04.2023, 07.08.2023, 20.10.2023 , 21.12.2023, 25.09.2024, 20.12.2024, 09.01.2025,04.03.2025 and 13.03.2026 are applicable to this tender.
I/We agree to carry out all works with use of modern equipments of required capacity for the work without extra payment. The decision of railway engineer shall be final and binding in this regard.
It is the responsibility of contractor to arrange the payment of the labour employed for the work through bank and to deduct PF as per the provisions of Minimum Wages Act.
The quantities shown above are approximate and to give a general guideline. Railway reserves a right to increase, decrease or to delete any of the items mentioned in schedule.
As per ACS 1 to GCC April 2022, issued vide Railway Board's letter dt. 14.07.2022, PVC Clause shall be applicable only in tenders having advertised value above Rs. 2 Crores provided to the provisions as per clause 46A-1. Tenderers should take a note and quote their rates accordingly.
In case Civil work tenders, the quantity of cement required in the items where necessary, will be used by the contractor on the same rates as accepted in tender, as per the quantity mentioned against each item in USSOR/DSR, though not mentioned in tender schedule.
Tenderers are advised to quote their rates including all type of taxes and levies etc. to be paid by them. Any extra payment will not be made on account of taxes/Levies etc., in excess of Contract Agreement Value,
In case of submission of Bid Security in the form of Bank Guarantee, a scanned copy of Original BG valid for a period of 90 days beyond the validity period of tender, and addressed in favour of Sr. DFM/WCR/BPL, shall be uploaded on IREPS portal while applying for tender. And As per ACS 2 to GCC April 2022, circulated vide Railway Board letter dt. 13.12.22, original BG should be delivered in person to the Concerned Official in Office before closing date for submission of bid (i.e. Excluding the last date of submission of bid) without fail. Any failure in this connection shall lead to summary rejection of bid.
Maintenance Period for this work will 24 months after successful completion of work.
Annexure V (A) certificate attached in technical eligibility criteria: Clarification Regarding submission of Annexure-V(A) as per NIT: In case of Partnership firm/Joint Venture (JV) / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc, the Annexure-V(A) must be submitted in the format as given in technical eligibility criteria link, by each partner in case of partnership firm / each member in case of HUF/ each JV member through their authorized signatory in case of Joint Venture firm as self-certification in individual capacity (not as bidder). Non- submission of the certificate, or submission of certificate either not properly filled in, or in a format other than the prescribed format shall lead to summary rejection of offer. For avoidance of doubt it is to make clear that this self-certification as they are individually not blacklisted/debarred......, shall be submitted by- 1. Each partner in case of partnership firm/Limited Liability Partnership (LLP) 2. Each member in case of HUF. 3. Each JV member through their authorized signatory.
Part-A) Bhopal - Construction of New Running Room (G+1) having 35 Room with 2 bed each near BPL lobby under ADEN(Works)Bhopal. Part-B) Bhopal- Upgradation work in Bhopal Dog Kennel under ADEN(Works)Bhopal.
WCR-BPL-W-26-27-HQ-06-19
WCR-BPL-W-26-27-HQ-06-19
Open
Works - General
12 Months
Bhopal, Madhya Pradesh
₹0
₹7.9 L
1 Jun 2026
7 May 2026
18 May 2026
170 items across 4 schedules · ₹25,82,704.17 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil | cum | 69 | 177.5 | 12,247.5 |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. | cum | 123 | 196 | 24,108 |
| 3 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. | cum | 218 | 700.5 | 1,52,709 |
| 4 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 93 | 7,294.7 | 6,78,407.1 |
| 5 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm | 297 | 392.15 | 1,16,468.55 |
| 6 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. | Sqm | 358 | 842.5 | 3,01,615 |
| 7 | Suspended floors, roofs, landings, balconies and access platform | Sqm 1473 | — | 927.25 | 13,65,839.25 |
| 8 | Lintels, beams, plinth beams, girders, bressummers and cantilevers | Sqm 3234 | — | 736.4 | 23,81,517.6 |
| 9 | Columns, Pillars, Piers, Abutments, Posts and Struts | Sqm | 973 | 961.3 | 9,35,344.9 |
| 10 | Stairs, (excluding landings) except spiral- staircases | Sqm | 70 | 764.95 | 53,546.5 |
| 11 | Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) | Sqm | 690 | 384.3 | 2,65,167 |
| 12 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg 17383 | — | 107.85 | 18,74,756.55 |
| 13 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg 38250 | — | 107.85 | 41,25,262.5 |
| 14 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum 175.38 | — | 9,504.75 | 16,66,943.06 |
| 15 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 510 | 9,860.4 | 50,28,804 |
| 16 | Cement mortar 1:4 (1 cement : 4 coarse sand) | cum | 469 | 9,344.35 | 43,82,500.15 |
| 17 | 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm). | Sqm | 57 | 2,600.45 | 1,48,225.65 |
| 18 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 90 | 3,167.95 | 2,85,115.5 |
| 19 | Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). | Sqm | 90 | 106.7 | 9,603 |
| 20 | Fixed to steel windows by welding | Kg 2270 | — | 219.1 | 4,97,357 |
| 21 | With 12 mm mild steel U beading | Sqm | 66 | 939.2 | 61,987.2 |
| 22 | 300x16 mm | Each | 100 | 216.55 | 21,655 |
| 23 | 200x10 mm | Each | 50 | 69.4 | 3,470 |
| 24 | 125 mm | Each | 100 | 39.95 | 3,995 |
| 25 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. | Each | 50 | 1,124.85 | 56,242.5 |
| 26 | 300x16 mm | Each | 44 | 303.25 | 13,343 |
| 27 | 125 mm | Each | 88 | 66.25 | 5,830 |
| 28 | Twin rubber stopper | Each | 50 | 72.35 | 3,617.5 |
| 29 | 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm ( +/- 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm ( +/- 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm ( +/- 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi- chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm ( +/- 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. | Sqm 54.72 | — | 3,253.8 | 1,78,047.94 |
| 30 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer- in-Charge. | Metre | 180 | 492.7 | 88,686 |
| 31 | Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) | Kg 1748 | — | 195.2 | 3,41,209.6 |
| 32 | Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete. | Each | 44 | 226 | 9,944 |
| 33 | 25 mm thick | Sqm | 50 | 1,948.25 | 97,412.5 |
| 34 | Size of Tile 600 x 1200 mm | Sqm 1330 | — | 1,798.8 | 23,92,404 |
| 35 | Size of Tile 600 x 600 mm | Sqm | 111 | 1,464.85 | 1,62,598.35 |
| 36 | Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. | Sqm | 53 | 3,186.7 | 1,68,895.1 |
| 37 | Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent | Sqm | 11 | 4,481.3 | 49,294.3 |
| 38 | 110 mm diameter | Metre | 222 | 377.4 | 83,782.8 |
| 39 | 110 mm | Each | 110 | 371.3 | 40,843 |
| 40 | 1:4 (1 cement: 4 fine sand) | Sqm 4366 | — | 347.05 | 15,15,220.3 |
| 41 | 1:4 (1 cement: 4 fine sand) | Sqm 1150 | — | 399.45 | 4,59,367.5 |
| 42 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. | Sqm 5516 | — | 262.7 | 14,49,053.2 |
| 43 | Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm | Sqm 5516 | — | 193.7 | 10,68,449.2 |
| 44 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture | Sqm | 120 | 170.7 | 20,484 |
| 45 | White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps | Each | 37 | 2,648.85 | 98,007.45 |
| 46 | 510x1040 mm bowl depth 250 mm | Each | 2 | 6,945.6 | 13,891.2 |
| 47 | 32 mm dia | Each | 37 | 119.55 | 4,423.35 |
| 48 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. | Each | 37 | 1,607.95 | 59,494.15 |
| 49 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. | Each | 37 | 168.35 | 6,228.95 |
| 50 | 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. | Each | 37 | 708.95 | 26,231.15 |
| 51 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. | Each | 37 | 18,212.9 | 6,73,877.3 |
| 52 | 15 mm nominal dia Pipes | Metre | 100 | 286.8 | 28,680 |
| 53 | 20 mm nominal dia Pipes | Metre | 100 | 335 | 33,500 |
| 54 | 25 mm nominal dia Pipes | Metre | 100 | 401.55 | 40,155 |
| 55 | 15 mm nominal dia Pipes | Metre | 100 | 497.8 | 49,780 |
| 56 | 20 mm nominal dia Pipes | Metre | 100 | 537.6 | 53,760 |
| 57 | 40 mm nominal dia Pipes | Metre | 200 | 563.05 | 1,12,610 |
| 58 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | Per Litre 16000 | — | 11 | 1,76,000 |
| 59 | 15 mm nominal bore, 86 mm long, weighing not less than 88 gms | Each | 40 | 125.6 | 5,024 |
| 60 | 15 mm nominal bore, 86 mm long, weighing not less than 88 gms | Each | 40 | 118.5 | 4,740 |
| 61 | 15 mm nominal bore, 107 mm long, weighing not less than 110 gms | Each | 40 | 208.45 | 8,338 |
| 62 | 15 mm nominal bore, 98 mm long, weighing not less than 75 gms | Each | 20 | 112.8 | 2,256 |
| 63 | 100 mm nominal dia | Each | 40 | 37.6 | 1,504 |
| 64 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. | Each | 38 | 111.45 | 4,235.1 |
| 65 | 300 mm dia. R.C.C. pipe | Metre | 80 | 994.3 | 79,544 |
| 66 | 300 mm dia piles | Metre | 722 | 3,065.6 | 22,13,363.2 |
| 67 | 300 mm dia piles | Each | 190 | 2,626.3 | 4,98,997 |
| 68 | Powder coated aluminium (minimum thickness of powder coating 50 micron) | Kg | 500 | 530.9 | 2,65,450 |
| 69 | Powder coated aluminium (minimum thickness of powder coating 50 micron) | Kg | 500 | 634.45 | 3,17,225 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TDGCCMarch_26.pdf
ATTACHMENT
PublicProcurementOrder1.pdf
ATTACHMENT
ELECTRICALSPECIFICATIONDOGKENNEL.pdf
ATTACHMENT
NewListofApprovedBrands.pdf
ATTACHMENT
SPECIALCONDITIONOFRUNNINGROOM_2.pdf Special Condition of Contract
ATTACHMENT
Annualcont.turnoverformatAnn.VIB_1.pdf
ATTACHMENT
DSRSpecificationsvolume1_compressed1.pdf
ATTACHMENT
DSRSpecificationsVolume2_compressed1.pdf
ATTACHMENT
JPOCABLECUT.pdf
ATTACHMENT
PCEcircular1.pdf
ATTACHMENT
SPECIALCONDITIONOFRUNNINGROOM_2.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .