GE/ALP (8368B) KOLKATA OF 2024-25

Amount

CHAIR VARENDAH (MS) : Supply and fixing for 20 mm dia, 16 Gauge thick MS conduit pipe of required length/size to be fixed duly arc welded and level the surface to make smooth and painted with one coat of red oxide zinc chrome primer after with and including dismantling the rusted/damaged leg/seat/back rest frame carefully without disturbing the adjoining parts of CHAIR VARENDAH ( MS ) complete all as specified and directed. Note : Ref drawing No FD-19,256,359

All as per item No 1 here in before but MS rod of 10 mm dia as connector of the front legs for Chair Verandah MS complete all as specified and directed.

Material and labour for removing of worn-out unserviceable cane & preparation of surface for painting by scraping old /fainted paint with sand paper/ machine or emery paper as applicable to make surface smooth and filing uneven gaps with putty there by make equal level with adjacent surfaces and there after applying synthetic enamel paint of approved shade/brand for chair verandah MS complete all as specified and directed.

Supply and fixing for caning with approved shade of plastic cane of 4 mm wide, 0.5 mm thick half-round as per godrej pattern white in colour as shown in the drawing "Mat pattern" for chair verandah MS complete all as specified and directed.

Supply and fixing for PVC shoe cap for Chair Verandah MS after with and including dismantling of worn out damaged unserviceable one complete all as specified and directed.

TEAPOY VARENDAH : Supply and fixing for 20 mm dia, 16 gauge thick MS conduit pipe of required length/size to be fixed after with and including dismantling the damaged leg/ frame carefully without disturbing the adjoining parts of TEAPOY VARENDAH complete all as specified and directed. Note : Ref drawing No FD-208

Supply and fixing for 19 mm thick pre laminated MDF board exterior grade (OSL) as on table top of TEAPOY VARENDAH with 4mm thick teak wood beading allround the top including polishing after and including taking down old unservicable top complete all as specified and directed.

Material and labour for preparation of surface for painting by scraping old /fainted paint with sand paper/ machine or emery paper as applicable to make surface smooth and filing uneven gaps with putty there by make equal level with adjacent surfaces and there after applying synthetic enamel paint of approved shade/brand for TEAPOY VARENDAH complete all as specified and directed.

Supply and fixing for hard rubber toe for TEAPOY VARENDAH after with and including dismantling of worn out damaged unserviceable one complete all as specified and directed.

CHAIR SCHOOL WITH HAND BOARD : Supply and fixing for PVC trough seat made of 4mm thick with 4x10 mm ribs moulded integrally and the same to be fitted to the frame with aluminum alloy screws after with and including removing feded/broken seat for chair school with hand board complete all as specified and directed. Note : Ref drawing No /FD/E6/MAP/05

All as per item No 3 here in before but 18 mm thick pre-laminated particle board of exterior grade OSD and edges with 1.5 mm thick PVC beading with wire nails as hand board after with and including removing of old unserviceable hand board for chair school with hand board complete all as specified and directed.

All as per item No 3 here in before but welding the disjointed MS plain bar shelf under the seat wherever required complete all as specified and directed.

All as per item No 3 above but painting the steel frame of chair with two coats of black synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply and fixing for PVC shoe cap for Chair school with Hand board after with and including dismantling of worn out damaged unserviceable one complete all as specified and directed.

CHARPOY GI PIPE : Removing the unserviceable ply /nylon newar from the charpoy GI Pipe complete all as specified and directed.

Material and labour for tightening the legs, junction points of long rail & short rail with pipe wrench, duly fixing with existing check nuts for becomes stable complete all as specified and as directed.

Supply and fixing for 32 mm dia GI Pipe medium grade long rail of 1890 mm long duly threaded the ends upto 22 mm size as shown in the drawing after with and including removing the old unserviceable long rail (whose thread ends were broken either at one end or both by loosing existing check nuts and elbows complete all as specified and directed. Note : Ref drawing No FD-220 and CEKZ/TD/556

Removing existing unserviceable short rail (whose thread ends were cracked) and fixing of 32 mm dia GI Pipe medium grade short rail of 813 mm long, 32mm dia GI pipe retrived from long rail i.e item No 4.02, duly threaded the ends upto 22 mm size as shown in the drawing complete all as specified and directed. Note : Ref drawing No FD-220 and CEKZ/TD/556

Removing existing unserviceable leg (whose thread ends were cracked) and fixing of 32 mm dia GI Pipe medium grade leg of 410 mm long, 32mm dia GI pipe retrived from long rail/short rail i.e item No 4.02 & 4.03, duly provided with 6 mm thick MS base plate duly welded & painted with two coats of black paint as shown in the drawing complete all as specified and directed. Note : Ref drawing No FD-220 and CEKZ/TD/556

Supply and fixing for 32mm dia 3 way elbow (ISI marked) for the joints of long /short rails as shown in the drawing after with and including dismantling of the same complete all as despecified and directed. Note: Ref drawing No FD - 220 and CEKZ/TD/556

Supply and fixing for 6mm thick check nut for the corner joints of long/short rails as shown in the drawing after with and including dismantling of the same complete all as specified and directed Note: Ref drawing No FD 220 and CEKZ/TD/556

Supply and fixing for 25mm dia medium grade GI pipe short rail of 890 mm long duty welded the ends to the long rail at an equal distance as shown in the drawing for resting the ply top for each charpoy GI and 6mm thickm MS Plate size (120 x 20mm) duly welded and painted to enable connecting 25mm dia GI piep & 32 mm dia GI pipe from undemeath rails for better grip while placing the ply top complete all as specified and directed. Note : Ref drawing No FD - 220 and CEKZ/TD/556

Supply and fixing of 12mm thick BWR grade Ply wood of size 7" x 3’ over the long rails & short rails through drilling holes in ply top and fixed with nickel nut, bolt and washer. The edges of ply should be applied mixture of french chalk powder shellac & solvent and added colour for smooth finish irrespective of drawing complete all as specified and directed. Note : Ref drawing No Fd-220 and CEKZ/TD/556.

TABLE CLERK STEEL/ TYPIST STEEL : Supply and fixing as in repair of drawer of Table Clerk Steel and Typist Steel with two coats of olive green paint over a coat of red oxide zinc chrome primer complete all as specified and directed. Note : Ref drawing No FD-84(M)/1004/1005

Supply and fixing for 19mm thick pre laminated particle board exterior grade (OSL) as on table top of Table Clerk Steel and Typist Steel with 4mm thick teakwood beading alround the top including polishing after and including taking down old unserviceable top complete all as specified and directed.

Material and labour for preparation of old painted steel surfaces of Table Office Clerk Steel / Typist Steel by scraping with emery paper, cleaning, re-dusting, making the surface smooth and applying one coat of synthetic enamel paint of approved shade/olive green/black as per direction of approved quality complete all as specified and directed.

TABLE OFFICE OFFICER STEEL : Supply and fixing as in repair of drawer with Table Office Officer Steel with two coats of olive green paint over a coat of red oxide zinc chrome primer complete all as specified and directed. Note : Ref drawing No FD-84(M)1003

Supply and fixing for 19mm thick pre laminated particle board exterior grade (OSL) as on table top of table office officer steel with 4mm thick teakwood beading alround the top including polishing after and including taking down old unserviceable top complete all as specified and directed.

Material and labour for preparation of old painted steel surfaces of table office officer steel by scraping with emery paper, cleaning, re-dusting, making the surface smooth and apply one coat of synthetic enamel paint of white shade/olive green/black as per direction of approved quality complete all as specified and directed.

TABLE (900X600) : Supply and fixing as in repair of drawer of table of size 900mm x 600mm with two coats of olive green paint over a coat of red oxide zinc chrome primer complete all as specified and directed. Note : Ref drawing No FD-1008

Supply and fixing for 19mm thick prelaminated particle board exterior grade (OSL) as on table top of Table (900X600) with 4mm thick teakwood beading alround the top including polishing after and including taking down old unserviceable top complete all as specified and directed.

Material and labour for preparation of old painted steel surfaces of table (900x600) by scraping with emery paper, cleaning, re-dusting, making the surface smooth and applying one coat of synthetic enamel paint of white shade/olive green/black as per direction of approved quality complete all as specified and directed.

Supply and fixing as in repair 25 mm square MS pipe of 16 guage thick standard steel for tables complete all as specified and directed. Note : Ref drawing No FD-84(M)/165/ 1003 /1004 /1005 /1008

Supply and fixing for hard rubber shoes of steel table's legs complete all as specified and directed. Note : Ref drawing No FD-84(M)/165/ 1003/ 1004/ 1005/ 1008

Supply and fixing for 4 lever lock with flat type SS key in duplicate for steel tables office cleark steel / office steel / office typist / table (900mm x 600mm x 760mm) complete all as specified and directed. Note : Ref drawing No FD-84(M)/ 1003/ 1004/ 1005/ 1008/ 165/ 1002

Supply and fixing as in repair for PVC receased handles for steel tables drawer complete all as specified and directed. Note : Ref drawing No FD-84(M) 1003/ 1004/ 1005/ 1008/ 165/ 1002

CHAIR CB STEEL WITH OR WITHOUT ARMS : Supply & Fixing for 25 mm dia, 16 gauge thick MS conduit pipe of required length/size to be fixed duly arc welded and level the surface to make smooth and painted with one coat of red oxide zinc chrome primer after with and including dismantling the rusted/damaged leg/seat/back rest frame carefully without disturbing the adjoining parts of CHAIR CB steel with arms and without arms. complete all as specified and directed. Note : Ref drawing No FD-75(M)

Material & Labour for preparation of surface for painting by scraping old /fainted paint with sand paper/ machine or emery paper as applicable to make surface smooth and filing uneven gaps with putty there by make equal level with adjacent surfaces and there after applying two coats of OG colour synthetic enamel paint of chair CB steel with arms and without arms complete all as specified and directed.

Supply and fixing for seat frame made out of Ist class teak wood and canned with 2 mm wide and 0.4 mm thick gola type of approved colour and 4 mm wide thick cane for borders and the frames shall be polished or painted as required to match the existing and fixed with 4 No GI nut and bolts of size 3" long with washers for chair CB steel with arms and without arms complete all as specified and directed.

All as per item No 9 here in before but back frame complete all as specified and directed.

All as per item No 9 here in before but arm rest made out of Ist class teak wood duly french polished and fixed with MS screw complete all as specified and directed.

Supply and fixing for hard rubber bush with MS screw for Chair CB steel with arms and without arms after with and including dismantling of worn out damaged unserviceable one complete all as specified and directed.

Supply and fixing for hard rubber cap for rear leg top side to be fixed for open end of the conduit pipe of chair CB steel with arms and without arms after with and including dismantling of worn out damaged unserviceable one complete all as specified and directed.

CHAIR EASY (CUSHIONED) STEEL :- Material and labour for legs of 19 mm square MS pipe 16 gauge of length 510 mm of CHAIR EASY (CUSHIONED) STEEL including dismantling of the existing unserviceable one complete all as specified and directed. Note : Ref drawing No FD-121 (M).

All as per item No 10 here in before but seat base rail of 19 mm square MS pipe 16 gauge of length 700 mm and complete all as specified and directed.

All as per item No 10 here in before but teak wood hand rest of size 19 mm x 65 mm of length 700 mm duly french polished and fixed with screws and complete all as specified and directed.

All as per item No 10 here in before but 50 mm thick, 40 D foam of size 560 mm x 635 mm, duly covered with approved shade leatherite over the existing 12 mm thick teak wood plank as per drg of seat base and complete all as specified and directed. Note : Cost of leatherite cloth shall not be less than Rs 350.00 per mtr.

All as per item No 10 here in before but 25 mm thick, 40 D foam of size 560 mm x 355 mm, duly covered with approved shade leatherite over the existing 12 mm thick teak wood plank as per drg of back rest base and complete all as specified and directed. Note : Cost of leatherite cloth shall not be less than Rs 350.00 per mtr.

All as per item No 10 here in before but jointing of 20 mm X 3 mm MS flat iron cleats between hand rest and MS square pipes with steel screws and complete all as specified and directed. Note : Ref drawing No FD-121 (M).

All as per item No 10 here in before but dismantled metal clamp back side of seat rest to be refixed with steel srews and complete all as specified and directed.

All as per item No 10 here in before but hard rubber shoes as per sample and complete all as specified and directed.

ALMIRAH/ LOCKER BED SIDE STEEL : Supply and fixing as in repair 6 lever lock with duplicate flat key (2 Nos of key) with existing size fixed with screw/ welding to shutter of almirahs complete all as specified and directed. Note : Ref drawing No FD-67/ 104 (M)/ 114 (M)/ 243/ 351/ 1031 / 1032

Supply and fixing as in repair for 3-way assembly including 6mm thick round bars with necessary fittings of approved quality for almirah complete all as specified and directed. Note : Ref drawing No FD-67/104(M)/ 114(M)/ 243/ 351/ 1031

Supply and fixing as in repair for 3-way assembly including 6mm thick round bars with necessary fittings of approved quality for almirah complete all as specified and directed. Note : Ref drawing No FD-67/104(M)/114(M)/ 243/ 1032

Supply and fixing as in repair handle of godrej pattern with necessary fixing accessories of approved quality complete all as specified and directed. Note : Ref drawing No FD-67/ 104 (M)/114(M)/ 243/ 351/ 1031/ 1032

Supply and fixing as in repair for new bottom made out of 1mm thick MS sheet made to shape and size on drawing and fixing by welding matching with existing almirah and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. Note : Ref drawing No FD-67/104(M)/ 114(M)/ 351/ 1031

Supply and fixing as in repair for new bottom made out of 1mm thick MS sheet made to shape and size on drawing and fixing by welding matching with existing almirah and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. Note : Ref drawing No FD-67/104(M)/114(M)/243/1032

Supply and fixing as in repair of new legs made out of 1mm thick of MS sheet and fixed with welding/riveteting for the bottom portion as per existing size and duly painted with two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. Note : Ref drawing No FD-67/104(M)/ 114(M)/ 351/1031

All as per item No 11.06 but for almirah medium steel complete all as specified and directed. Note: Ref drawing No FD: 67(M) /104(M)/114(M)/243/1032

Supply and fixing as in repair of new MS hinges or U clips of same shape & size as existing in steel almirah by fixing duly welded complete all as specified and directed. Note : Ref drawing No FD-67/104 (M)/114 (M)/243/351/ 1031 /1032

Supply and fixing as in repair for new shelves made out of 1mm thick MS sheet made to shape and size on drawing and fixing with cleats, nuts and bolts complete all as specified and directed. Note : Ref drawing No FD-67/104(M)/ 114(M)/ 351/1031

All as per item No 11.09 but for almirah medium steel complete all as specified and directed. Note: Ref drawing No FD: 67(M) /104(M)/114(M)/243/1032

All as per item No 11.09 but for locker bed side steel and complete all as specified and directed. Note : Ref drawing No FD-1029

Taking down of door shutter of almirahs and bringing the item to the original shape and refixing the repaired door shutters with suitable hinges complete all as specified and directed. Note : Ref drawing No FD-67/ 104(M)/114(M)/ 243/ 351/ 1031/1032

Taking down of existing dented shelves from almirahs steel bringing the item to the original shape and refixing the shelves with necessary cleats/nuts/bolts including two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. Note : Ref drawing No FD-67/ 104(M)/114(M)/ 243/ 351/ 1031/ 1032

PAINTING : Material and labour for preparation of old steel surfaces by scraping with emery paper, cleaning, reducing, making the surfaces smooth and applying putty wherever required and applying one coat of synthetic enamel paint of approved shade of approved make & quality inside and out side of almirah large steel with shelves complete all as specified and as directed. Note : Ref drawing No FD-67/104(M)/ 114(M)/ 351/1031

All as per item No 12 here in before but almirah medium steel with shelves and complete all as specified and directed. Note : Ref drawing No FD-243/1032

All as per item No 12 here in before but almirah large glazed steel with shelves and complete all as specified and directed. Note : Ref drawing No FD-104(M)

All as per item No 12 here in before but almirah medium steel with shelves 1/2H, 1/2SH and complete all as specified and directed. Note : Ref drawing No FD-114

All as per item No 12 here in before but Book Case steel and complete all as specified and directed. Note : Ref drawing No FD-69(M)/1028

All as per item No 12 here in before but but book case steel 4 compartrments and complete all as specified and directed. Note : Ref drawing No FD-90

All as per item No 12 here in before but rack side 3/4 spaces steel and complete all as specified and directed. Note : Ref drawing No TP

All as per item No 12 here in before but rack side with tray (size 711x685x254mm) steel and complete all as specified and directed. Note : Ref drawing No FD-97(M)/FD-1023

All as per item No 12 here in before but locker steel and complete all as specified and directed. Note : Ref drawing No FD-1029

All as per item No 12 here in before but rack steel adj 6 tier and complete all as specified and directed. Note : Ref drawing No FD-1038

All as per item No 12 here in before but rack steel storage (size 1830x760x905mm) and complete all as specified and directed. Note : Ref drawing No FD-129(M)

RACK SHOE STEEL : Supply and fixing for 25 mm dia, 16 gauge thick MS conduit pipe of required length/size to be fixed after with and including dismantling the damaged leg frame carefully without disturbing the adjoining parts of RACK SHOE STEEL complete all as specified and directed. Note : Ref drawing No FD/E6/MAP/02

Supply and fixing for 6 mm dia MS rod of required length/size to be fixed after with and including dismantling the damaged shelf (frame) carefully without disturbing the adjoining parts of RACK SHOE STEEL complete all as specified and directed.

Supply and fixing for 3 mm dia MS rod of required length/size to be fixed after with and including dismantling the damaged shelf (mesh) carefully without disturbing the adjoining parts of RACK SHOE STEEL complete all as specified and directed.

Material and labour for preparation of old steel surfaces by scraping with emery paper, cleaning, reducing, making the surfaces smooth and applying putty wherever required and applying one coat of synthetic enamel paint of black shade of approved make & quality for RACK SHOE STEEL complete all as specified and directed. Note : Ref drawing No FD/E6/MAP/02

CHARPOY WITH HARDTOP : Supply and fixing for 25X65 mm, 16 Gauge thick MS Tube of required length/size to be fixed after with and including dismantling the damaged long rail/short rail carefully without disturbing the adjoining parts of CHARPOY WITH HARDTOP complete all as specified and directed. Note : Ref drawing No FD/MAP-II/01

All as per item no 14 but 32x32 mm, 16 gauge thick MS tube of required length/size to be fixed after with and including dismantling the damaged leg frame carefully without disturbing the adjoining parts of CHARPOY WITH HARDTOP complete all as specified and directed.

All as per item no 14 but 25X25 mm, 16 gauge thick MS tube of required length/size to be fixed after with and including dismantling the damaged stiffner carefully without disturbing the adjoining parts of CHARPOY WITH HARDTOP complete all as specified and directed.

Supply and fixing for 12mm thick BWR grade ply wood of size 6'6" x 3’ over the long rails & short rails fixed with nickel nut, bolt and washer. The edges of ply should be applied mixture of french chalk powder shellac & solvent and added colour for smooth finish irrespective of drawing complete all as specified and directed.

Material and labour for preparation of old steel surfaces by scraping with emery paper, cleaning, reducing, making the surfaces smooth and applying putty wherever required and applying one coat of synthetic enamel paint of black shade of approved make & quality for CHARPOY WITH HARDTOP complete all as specified and directed.

Supply and fixing for hard rubber toe for CHARPOY WITH HARDTOP after with and including dismantling of worn out damaged unserviceable one complete all as specified and directed.

CHAIR COMPUTER/ REVOLVING : Supply & Fixing for twin castor wheel of size 50mm dia as per sample of chair computer / revolving low or high back after and including dismantling the old unserviceable one carefully without damaging the adjoining parts complete all as specified and directed. Note : Ref drawing No TP-FD/E6/MAP/01

All as per item No 15 here in before but stainless steel pedestal assembly complete

All as per item No 15 here in before but acrylic fabric for seat and back as per approved shade and S&F transparent plastic dust sheet covers for seat and back Note: Unit shall be each seat and each back Note: Rate of cloth should not be less than 420.00 per sq mtr

All as per item No 15 here in before but gas lift rod with proper adjusting tilt.

All as per item No 15 here in before but arm rest pair.

All as per item No 15 here in before but polyurethane foam of 50 mm thick of density 40 best quality for seat and back with lipping.

P N GUPTA AND SONS (BID ID -3138659)

Tirupati Buildcon Pvt. Ltd. (BID ID -3139273)

SANKAR TRADERS (BID ID -3140141)

REMCO (BID ID -3140162)

SOVA ENTERPRISE (BID ID -3138192)

RADHA ENTERPRISE (BID ID -3145135)

ROY CONSTRUCTION (BID ID -3133009)