PROVN OF URINAL BLOCK NEAR STN PT GROUND, PROVN OF SAFETY TO OVER HEAD TANK IN KV AREA, SR TO STREET LIGHT AND PAINTING OF POLES AND PROVN OF STANDBY SUPPLY FOR PAR EQPT AND INSTALLATION OF ISOLATION TRANSFORMER AT CERTAIN LOC AT TECH AREA UNDER GE (

Amount

SCHEDULE 'A' PART-I Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, etc and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for Brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M & L for 40 mm thick, Cement Concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) Damp proof course to horizontal or vertical surfaces including necessary form work mixed with and including water proofing compound as per manufacturer's instructions complete all as specified and directed.

M & L Reinforced Cement Concrete 1:1.5:3, Type A-1 (Nominal Mix) (using 20 mm graded stone aggregate) as in beams, cantilevers, lintels over 1.5m span complete all as specified and directed. (Note : Reinforcement will be measured & paid seperately)

M & L for use & waste Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etcetc complete all as specified and directed.

S & F TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

S & F Mild steel TMT bars 5mm dia and over upto and including 10mm dia in strirrups, spacers and binders spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed.

M & L for Rolled mild steel fo grade Fe 410-W (Gde-E- 250) quality-A as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat section) including distance pices, cleat etc complete all as specified and directed.

S & F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zine chrome primer complete all as specified and directed.

M & L for rendering 15 mm thick in two coats (10mm+5mm each) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with integral water proofing compound with weight of cement in top layer as per manufacturer's instructions and finished the surface even and fair without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

Supply only Liquid water proofing compound (ISI marked) complete all as specified and directed.

M & L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M & L for hardcore of gauge n.exc 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for 75 mm thick, plain cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in sub-base of floooring/hard standing, etc complete all as specified and directed.

M & L for 50 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for joint free non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc, including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for Glazed, ceramic, coloured tiles of size 300mm x 200mm x 6-7mm thick, on vertical surfaces such as skirting, dados etc, including 10 mm thick bedding in cement mortor 1:4 and set & jointed in neat cement slurry & pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for preparing newly plastered surfaces of walls, etc and applying three coats of white wash complete all as specified and directed.

M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

S & F solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing and as directed.

S & F 100mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S & F 125 mm size, Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 150 mm long, Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S & F Vitreous China urinal, half stall type, white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete complete as specified and directed.

S & F 40 mm dia, High density poly-ethylene pipes, (HDPE) of pressure rating 6 kgf/cm 2 laid as in waste pipe complete all as specified and directed.

S & F 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends complete all as specified and directed.

S & F 15mm bore, angle Stop valve of PTMT, any colour high pressure, screwed for iron pipe and fixed (minimum weight 90 gms) complete all as specified and directed.

S & F 32 mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S & F Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and directed

S & F 15mm bore Urinal spreader chromium plated for urinals complete all as specified and directed.

S & F 75 mm bore, PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed.

S & F 20 mm bore, Brass chromium plated, tubular towel rail, D type, 60 cm long between flanges with brackets complete all as specified and directed.

S & F 75 mm bore, PVC (SWR), Soil waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors, etc complete all as specified and directed.

Supply, laying, connection and testing, 15mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

Supply, laying, connection and testing, 20mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

S & F 500 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top), hoisted and fixed in position as specified in SSR Part I and directed.

S & F 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and directed.

S & F Steel ventilator with top hung shutter including hinges, steel peg stay, complete complete all as specified and directed.

S & F 110 mm bore, PVC (SWR), Soil waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors, etc complete all as specified and directed.

M & L for plain cement concrete 1:3:6, type C-2 (using 40 mm graded broken stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete for 110 mm bore drain pipe complete all as specified and directed.

M & L for Plain cement concrete 1:2:4, type B-1, (using 20 mm graded stone aggregate) as in benching, coping, lintel upto 1.5m span cast in situ including necessary form work complete all as specified and directed.

S & F Vitreous china urinal partition white of size 310x700 mm terminating about 40cm above floor line complete with all fixing accessories complete all as specified and directed.

S & F 3 mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

M & L for Plain cement concrete 1:2:4, type B-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for use & waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams and similar work, vertical or to batter complete all as specified and directed.

M & L for Mild steel framed work such as grills, gratings, gates etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-410-0 Gde E-250 complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed.

Taking down street light fittings/flood lights of any type any capacity from existing pole after disconnecting all electrical connections and removing from the site complete all as specified and directed.

M & L for Sand cushioning with clean dry sand in trenches for protection of under ground cables (below, above and around the cable laid in trenches) complete all as specified and directed. (Note: Thickness after punning down shall be measured for payment)

Supply and laying well burnt bricks, sub class 'B' bricks laid breath wise across the length of cable in trenches for protection of UG cables complete all as specified and directed.

M & L for 40 mm bore, steel tubes, galvanised, light grade with all fittings, laid in floor/road crossing/drain etc as in cable protection complete to walls and ceilings or laid in floors including taking up or down existing pipe complete all as specified and directed.

Supply and laying cable XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 Sqmm 2 core including taking out old one complete all as specified and directed. (Note: Excvation and earth work shall be measured and paid seperately)

All as per serial item No. 59 above but for 16 Sqmm 4 core cable complete ditto

M & L for Preparation of old painted surface above the planting depth/PCC coping of steel tubular LT pole upto 11.00 metre long including MS clamps, cable protection pipe, bracket fitted with steet light fittings etc by scraping with steel wire brush and applying two coats of aluminium paint to external surface of poles, MS cross arms, MS clamp, cable protection pipe etc to give even shade including Zebra colour of painting upto 2.1 m height from the top of coping/bottom of pole as per site condition and numbering of poles complete all as specified and as directed by the Engr-in-Charge. (Note : Zebra colour will be applied by synthetic enamel paint of black/yellow colour as approved in alternate layer of 30 cm height of each layer).

M & L for Writing letters or figures (Block ,Roman, Italic or Indian) n. exc 5 cm height with synthetic enamel paint as in numbering of pole etc complete all as specified and directed.

S & F in repairs, three core twisted, flexible copper conductor wire of size 1.00 Sqmm for connection complete all as specified and directed.

M & L for boring of horizontally holes by manual method under road below 1 metre from the road surface and dia of hole not exc 100mm without damaging the exsting road, getting out and disposal of excavated soil, etc to a distance not exc. 50 meter from the site of work complete all as directed by Engineer in charge.

S & F in repair cable junction box, IP 66/67 weather proof for outdoor installation (with knockout for cable entry), 10-16 Sqmm of size 155x210x92mm with terminals including fixing arrangement to the street light pole with suitable size of clamps, nuts & bolts as directed. (Make : HENSEL, Cat No : KF 1616 or equivalent model as per list of manufacturer's)

S & F MCB, SP, 240 Volts, 5 to 32 Amps, 'C' Series, 10KA capacity, 240 Volts complete all as specified and directed. (Make: Legrand Cat No. 4085 87-95 or equivelant of make as per list of manufacturer)

S & F LED street light fittings, 45 Watt in aluminium PDC housing toughened glass cover with IP 66 protection icnluding lamp and connecting up and testing complete all as specified and directed. (Make : Surya Cat No. SLE UL 45W IP66 LXN and equivelant model of make as specified in list of manufacturer).

S & F LED street light fittings, 60 Watt in aluminium PDC housing toughened glass cover with IP 66 protection icnluding lamp and connecting up and testing complete all as specified and directed. (Make : Surya Cat No. SLE UL 60W IP66 LXN and equivelant model of make as specified in list of manufacturer).

Supply, Install, testing and commissioning Isolation transformer, 10 KVA, three phase, 50 Hz, copper wond, oil cooled, class of insulation A, matellic body duly powder coated designed for input voltage range 415 + 5% and output voltage range 415 + 5%, ratio 1:1, vector group: Dyn 11, Delta - Star, indoor IP 42 (CPRI Approval required) with first filling of transformer oil of requisite dielectric strenght upto level, efficiency more than 95%, seperate neutral bushing shall be brought out for earthing, Potential difference between neutral to earth less than one volt with all standard fittings like digital temperature meter, adequate number of cooling radiators, lifting hooks one set, earthing terminal two Nos complete with over load/short circuit protection of circuit complete all as specified and directed

All as per serial item No. 69 above but of capacity 25 KVA complete and ditto

Supply and laying cable XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 Sqmm 4 core complete all as specified and directed. (Note: Excavation and earth work shall be measured and paid seperately)

All as per serial item No. 71 above of size 25 Sqmm 3.5 core complete ditto.

Supply, Install, testing and commissioning silent diesel engine driven generating set including alternator, capable of delivering output of 20 KVA, 415 Volts, 3 phase, 4 wire, 50 Hz, 0.8 PF engine as per IS:10001/10002 and alternator as per IS:13364 complete with relay panel and switch gears for automatic starting on main failure control panel having meter and sound proof canopy as per CPCB norms and suitable foundation complete as per manufacturer's instructions complete all as specified in Annexure 'A' to BOQ.

Supply anf fix on load Change over switch, general purpose with side handle, current rating 63Amps, 4 pole, 415 V, 50 Hz complete all as specified and directed. (Make: Havell's Cat No. IHCFFE0063 or equivelant approved make as per list of manufacturer)

Surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for 100 mm thick, Cement concrete 1:2:4, type B-2 (using 40mm graded stone aggregate) as in base of flooring/hard standing, etc, and finished the cement concrete surfaces even and fair without using extra cement complete all as specified and directed.

M & L Earthing complete with GI earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected with galvanised earth strip of size 32x6mm dia by means of bolts, nuts, check nuts and washers protected by 40mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, with 50 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel, wire mesh, aluminium lugs, complete in all respect and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion complete all as specified and as directed by the Engineer-in-Charge.

B L SHARMA

MAJUMDER ENTERPRISE

M/S. KUMAR CONSTRUCTION CO.

M/S ANNI ENTERPRISE

M/S ASHOK ENTERPRISE

MAA TARA TRADING