SPECIAL REPAIRS TO KITCHEN AT BLDG No. P-31,P-32,P-117 P-136 , SPECIAL REPAIRS TO SERVANT QTRS IN BLDG NO.P-75 P-76 AND SPECIAL REPAIR TO ROOF AND CEILING IN BLDG NO.P-135 OFFICERS QTRS AT LICHUBARI IN JORHAT MILITARY STATION UNDER GE JORHAT

Amount

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) complete all as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) complete all as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n. exc. 1.5 Sq. M each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sq. M but not exc. 4.0 Sq M each, complete all as directed.

Dismantling timber scantling in unframed work, 40 Sq cm and over in section, in any position, complete all as directed.

Taking down of shutters of any description n exc 1 sqm each with iron mongries and all fittings complete and remove to store complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as directed.

Dismantling timber fillets, rails, posts, rafters,purlins, etc. under 40 sq. cm in section, in unframed work,complete all as directed.

Dismantling of Asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete all as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as directed.

Dismantling water tanks of capacity exceeding 250 litres & not exceeding 500 litres and removing to store for taking credit,complete all as directed.

Taking up or down, steel tubing 15 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

Taking up or down, steel tubing 20 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

Taking down SWR pipes (any size or pattern), including all fittings, 'T', bends,etc., including removal to store for taking credit (measured overall as fixed along the centre line over fittings and accessories), complete all as directed.

Taking down cement plaster of any description or cement concrete (not exc. 50mmm depth) including racking out joints, hacking for key, scrubbing down with water to make the surface absolutely free from loose dust, dirt, oil, grease, foreign materials etc. and removing rusts from rusted re-inforcement by applying Dr, Fixit rust remover to RCC chajja ,lintel ,roof and beam including protective coating to rusted re-inforcement by applying a single coat of Dr. Fixit epoxy zinc primer (rate of application as per manufacturer's instruction) including removal of all scale and corrosion deposits to effected re-inforcement and applying two coats of Dr. Fixit epoxy bonding agent (rate of application as per manufacturer's instruction) on old concrete with Drilling holes @ 150mm C/C both way 150mm depth at an angle 45 degree and supply and fixing of MS nozzles in position 8mm dia, 125mm long, outer threaded both ends, properly tied with Dr. Fixit concrete repair mortar about 30-40mm wide and 2-3 mm thick band, including hire charges and providing polyurethane injection grout through pre fixed MS nozzle using Dr. Fixit PU Plain injection of M/S Pidilite Industries Ltd; 2 component injection resin system by pressure gauge pump in slow rate (3kg/Sqcm), storing, mixing and application to be done strictly in accordance with the manufacturer's instructions with and including providing pre-packed, three component structural grade epoxy mortar (Dr. Fixit repair mortar) of Pidilite Industries Ltd Storing, mixing and application to be done strictly in accordance with the manufacturer's instructionsincluding necessary scaffolding supports, prop etc. complete all as specified and as directed.

Materials and Labour for, broken stone or boulder hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface , complete all as specified and directed.

Materials and Labour for plain cement concrete (1:3:6) type C1 using 20 mm graded aggregate in lintels up to 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height,copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary from work complete all as specified and directed.

Materials and Labour for plain cement concrete (1:2:4) type B1 using 20 mm graded aggregate in lintels up to 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary from work complete all as specified and directed.

Materials and Labour for reinforced cement concrete 1: 1.5 :3, Type A1(using 20 mm graded aggregated) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and like,,complete all as specified and directed.

Materials and Labour for plain cement concrete (1:3:6) type C2 using 40 mm graded aggregate as in surface channels and drains complete all as specified and directed.

Materials and Labour Extra for forming fair finishing to surfaces channels/drain 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, etc complete all as specified and directed.

Supply only liquid grade to IS 2645 water proofing compound

Materials and Labour for brick work with Sub Class ‘B’ bricks straight or curved on plan exceeding 6M mean radius built in cement mortar (1:6), complete all as specified and directed.

Materials and Labour for brick work with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in built in CM (1:4),complete all as specified and directed.

Materials and Labour for,cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, in stone concrete block or slab walls, complete all as specified and directed.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete, flat, complete all as specified and directed.

Materials and Labour for waterproofing treatment to existing RCC roof in the following steps complete all as specified and directed. (i) Complete removal of the existing water proofing treatment. (ii) Wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown grade bitumen of any penetration applied hot @ 1.7 kg per sq. m, blinded with grit or pea size gravel @ 0.006 cu.m per sq.m, and lightly tampered (area of flashings, etc., shall be added to the roof area) (iiii) Supply and Laying, chicken wire mesh of size 12.5 mm x 0.51 mm (24 SWG) hexagonal construction including all laps, cutting and waste in fabric reinforcement to PCC roof padding including providing 40 mm thick plain cement concrete (1:2:4) type B0using 12.5 mm graded aggregates as in roof padding. (iv) Providing 15 mm thick screed bed or bedding layer of cement mortar (1:3), mixed with liquid water proofing compound as per manufactures instructions, on concrete surface of roofs or terracing and finishing surface even and smooth without using extra cement. (iv) Waterproofing treatment over smooth finished surfaces after application of cold applied bituminous primer @ 0.30 Kg /Sq M,, providing and laying APP polymer, modified, non-woven polyester fabric of 150 grams/square metre, reinforced membrane, 3.00 mm thick, weighing 3.00 Kg / Sq M, with surface finish of white mineral, by torch on application method, with minimum 75 mm overlap on longitudinal direction and 100 mm overlap on the transverse direction and finally applying with one coat of bituminous based solar reflective aluminium paint @ 100 gms / Sq M complete all as specified and directed.

Supply and Fix, second-class hard wood timber scantlings, clean sawn, in unframed works and in any position, fixed with nails complete all as specified and directed.

M & L for 18/19mm thick block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on one face, fixed with screws to timber frame work complete all as specified and directed.

M & L for 6mm thick (5 ply) plywood, grade BWP, type BB, fixed with screws to timber frame work complete all as specified and directed.

M & L for 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work built in furniture items including teak wood leaping 6mm thick externally complete all as specified and as directed.

S & F of 75mm size hasp and staple safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S & F continuous (piano) hinges, brass, bright finish or electrogalvanised, width of flaps when open in 30mm complete all as specified and directed

M&L for 3 mm dia IS marked stainless steel cup plate rack of size 4' x 17' x 20' complete all as per specified and directed.

M&L for 3 mm dia IS marked stainless steel meals plate rack of size 6' x 17' x 20' complete all as per specified and directed.

M&L for 3 mm dia IS marked stainless steel catlery basket of size 4' x 17' x 20' complete all as per specified and directed.

M&L for 3 mm dia IS marked stainless steel bottle basket of size 8' x 17' x 20' complete all as per specified and directed.

M&L for drawer with approved sliding channel and site battens make of approved black board 19 mm thick complete all as per specified and directed.

M&L for decorative laminate type - I of surface finish white and pattern as approved fixed with approved addsive and albro tape and as per manufacures instructions 0.9 mm thcik complete all as per specified and directed.

M&L for decorative laminate type - I of surface finish coloured and pattern as approved fixed with approved addsive and albro tape and as per manufacures instructions 0.9 mm thcik complete all as per specified and directed.

M&L for stainless steel hings 19 mm long L type complete all as per specified and directed.

M&L for stainless steel hings 12 mm long L type complete all as per specified and directed.

M&L for stainless steel hings 6 mm long L type complete all as per specified and directed.

M&L for stainless steel handle 150 mm long grip length complete all as per specified and directed.

M&L approve size of door magnate fitted to shutters complete all as per specified and directed.

Supply and fixed second class hardwood bedding as in cornices / picture rails and the like sectional area in square cm not exc 6 complete all as specified and directed.

Supply and Fix, factory made rigid lam PVC door frame of size 125 mm x 50 mm, double rebated with wall thickness of extruded 5mm PVC sheet of density 600 kgs/cum , made by joining 3 Nos. heat bent PVC sheet 'C' channel of 5mm PVC foam sheet of size 35mm x 35mm x 25mm & 40mm x 55mm x 40 mm & 25 mm x 35 mm x 35 mm using solvent cement, the two side 'C' channel shall be reinforced with 19mm x 19 mm MS square tube of 19 SWG with all three 'C' ed to flat base of 5mm PVC sheet with solvent cement. The profile shall be mitred cut at two corners and jointed by inserting 4 Nos. 150 mm long brackets of 15mm x15 mm MS square tube inside the 19 mm square tubes. The two vertical members of door frame shall be reinforced with 40mm x 20 mm MS tubes of 19 SWG duly filled with 2nd class hardwood throughout the frame. The door frame shall be fixed to the wall using 100 mm long nikel coated dry wheet screws through the frame by using PVC fastener. Minimum 08 Nos. of screws shall be provided for each vertical member and minimum 04 Nos.for horizontal members etc. as per manufacturers specifications, fixed in opening, complete all as specified and directed.

Supply and Fix, factory made rigid lam PVC door frame of size 100 mm x 50 mm, double rebated with wall thickness of extruded 5mm PVC sheet of density 600 kgs/cum , made by joining 3 Nos. heat bent PVC sheet sections. The inside section of size 90mm x 30 mm shall be made from colour PVC sheet of 5 mm thickness.The inside section shall be covered by sticking two sections of size 35mm and 6 x 45 mm made from 5mm thick plain sheet. The frame shall be mitred cut at two corners and jointed by inserting 4 Nos. 150 mm long brackets of 15mm x15 mm MS square tube. The two vertical members of door frame shall be reinforced with 40mm x 20 mm MS tubes of 19 SWG duly filled with 2nd class hardwood throughout the frame. The door frame shall be fixed to the wall using 100 mm long nikel coated dry wheet screws through the frame by using PVC fastener. Minimum 04 Nos. of screws shall be provided for each vertical member and minimum 02 Nos.for horizontal members etc. as per manufacturers specifications, fixed in opening, complete all as specified and directed.

Supply and fix solid PVC door frame of size 50 mm X 47 mm made out of 5 mm single side prelam PVC sheet with edges painted to match with prelam sheet, reinforced with MS square tube, fixed in opening, complete all as specified and directed.

Supply and Fix, factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail: Panelling of both sides prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed to door frame complete all as specified and directed.

S & F 30mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a); fitted to chowkats

Supply and Fix, factory made wire gauzed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

Supply and Fix, 35mm thick factory Made Solid PVC Moulded Door Shutter with particle board core, 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam PVC Sheet on the front face & 2 mm prelam PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed.

Supply and Fix, factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed.

Supply and Fix,IS marked Stainless steel butt hinges, medium weight, cold rolled 100 mm size complete all as specified and directed

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 200 mm long complete all as specified and directed.

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 150 mm long complete all as specified and directed.

Supply and Fix, extruded aluminium alloy handles, fabricated type, anodized, 100 mm size, complete all as specified and directed.

Supply and Fix, aluminium handles, cast type, anodized, 150 mm size, complete all as specified and directed.

Supply and Fix, brass chromium plated, towel rail, 20mm dia, D type, 60cm long between flanges, including taking down existing one complete all as specified and directed

S & F 600mm long towel rail of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 190gms

Supply and Fix, in repair decorative drapery curtain rod 25 mm dia chromium plated with including fancy side ,brackets complete all as specified and directed.

Supply and Fix, floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring and with overall length of cover plate 150 mm, fixed in floor, complete all as specified and directed.

Supply and Fix, Aluminium Alloy, anodised, sliding door bolt, length of bolt 300 mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Supply and Fix, stainless steel wire cloth, 0.36mm nominal dia. of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Supply and fix mild steel TMT bars 10 mm dia. and over, cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed

Materials and Labour for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Grade E-165 complete all as specified and directed.

Supply and Fix,steel ventilator with top hung shutter including hinges, steel peg stay, complete without glazing bars, dovetailed or welded, including taking down existing unserviceable one including making good disturbed surfaces as per existing specfication complete all as specified and directed.

Supply and fix Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, including taking down existing unserviceable one including making good disturbed surfaces as per existing specfication complete all as specified and directed.

Supply and fix Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, including taking down existing unserviceable one including making good disturbed surfaces as per existing specfication complete all as specified and directed.

Supply and Fix, 0.80 mm thick, plain, galvanised, mild steel sheeting in stepped flashings (measured as the minimum rectangle from which the pieces can be cut),grade of coating 275, with minimum zinc coating of 275 gms. /Sq m,complete all as specified and directed.

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based plain steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed

Materials and Labour for exposed metal frame ceiling with 6mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid with and including exposed metal frame using hot dip galvanised steel, exposed pre-coated ceiling suspension system of grid size 600 mm X 600 mm, with main runner ‘T’ section 24 mm (W) X 38 mm (H) X 0.60 mm (T), cross ‘T’ section 24 mm (W) X 28 mm (H) X 0.30 mm (T) , wall angle 24 mm X 24 mm X 5 mm (T) and suspended with 4 mm dia. GI hangers/wire fixed with steel dash fasteners from purlins/soffits spaced at 1200 mm centre to centre with butterfly clips, hold down clips, providing provisions for light fixtures, air conditioning diffuser and ducts, sprinklers, smoke detectors etc., complete all as specified and directed.Make of boards by Ramco industries Ltd and GI grid by Gabson eternity /Armstrong

Materials and Labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded aggregates as in plinth protection including finishing surface even and smooth without using extra cement complete all as specified and directed.

Filling joints in plinth protection, 30 mm deep x 10 mm wide, filled solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and directed.

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11sqm,conforming to IS 15622, ISO 13006, EN 14411 Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed.

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,conforming to IS 15622, ISO 13006, EN 14411 Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and MAKE:- (Johnson/Kajaria or equivalent make ) directed.

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,conforming to IS 15622, Grade B II, on vertical surfaces of wall such as dados, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.MAKE:- (Johnson/Kajaria or equivalent make )

Materials and Labour for, digital Glazed ceramic coloured tiles, 450 X 350 X 8 mm thick, conforming to ISO 13006, EN 14411 , Group B III, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match with over and including 10mm thick rendering CM 1:3 complete all as specified and directed. MAKE:- (Johnson/Regency/Kajaria)

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,conforming to IS 15622, ISO 13006, EN 14411 Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed.MAKE:- (Johnson/Kajaria or equivalent make )

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,conforming to IS 15622, Grade B II, on vertical surfaces of wall such as dados, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.MAKE:- (Johnson/Kajaria or equivalent make )

Materials and Labour for Granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, over and including 20 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and directed.

Materials and Labour for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and including 15mm thick rendering complete all as specified and directed.

Material and Labour for Machine Pressed Precast Concrete Interlocking Paver Block ,with grey cement and pigment, any shape and size conforming to IS 15658-2006, of 60 mm thickness, M-35 Grade,laid on pavements, complete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded aggregate as in sub base/paving/hardstanding , complete all as specified and directed.

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed.

Materials and Labour for rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed. Note: - (Water proofing compound will be measured and paid separately)

Material and Labour for applying two coats of white wash to old surfaces on walls including preparation of surfaces complete all as specified and directed.

Materials and Labour for applying applying two coats of oil bound distemper, white or tinted, to new plastered surfaces on walls, over and including 1mm thick wall care putty premium quality over priming with alkali resistant priming paint and including preparation of surfaces, complete all as specified and directed.

Material and Labour for complete removal of existing treatment and applying two coats of oil bound distemper,white or tinted over 3mm thick wall care putty, to old plastered or unplastered surfaces on walls including preparation of surfaces, complete all as specified and directed.

M&L for preparation existing treatment from pillar, beam, , wall s etc including cornices, abraded to remove all laitance, paints, mark/spot etc by washing rubbing down and stopping and applying one coat of acrylic base weather coat (exterior grade Ist quality ) painting with one or more approved shades complete all as specified and directed.

M&L for removal of complete existing treatment from pillar, beam, , wall s etc including cornices, abraded to remove all laitance, paints, mark/spot etc by washing rubbing down and stopping and applying two coat of acrylic base weather coat (exterior grade Ist quality ) painting with one or more approved shades over a coat of primer as per manufacturers instruction complete all as specified and directed.(Note : Second coat will be done after complete dried up of 1st coat as and when ordered and approval of 1st coat as directed

Supply and Fix,3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

Supply and Fix,4 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

Material and Labour for applying one coat of synthetic enamel paint on old painted steel and iron surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for applying one coat of synthetic enamel paint on old painted wood or wood based surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Materials and Labour for galvanized steel tubing, medium grade, 15 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

Fixing Only, galvanized steel tubing, medium grade,15 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed. Note:- Steel tubing obtained from Serial Item No.15 here in before shall be re-fixed.

Materials and Labour for galvanized steel tubing, medium grade, 20 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

Fixing Only, galvanized steel tubing, medium grade,20 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed. Note:- Steel tubing obtained from Serial Item No.16 here in before shall be re-fixed.

Material and Labour for 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part – I complete, all as specified and directed.

Materials and Labour for, Ball valves high pressure of PTMT (Minimum weight 210 gms) with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe, 20 mm bore and fixed complete all as specified and directed.

Supply and Fix, in repair bib tap, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, complete all as specified and directed.

Supply and Fix, in repair stop valves/Angle cock, cast copper alloy, fancy type, chromium plated,screwed down, high pressure with crutch or butterfly handle, screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.

Supply and Fix, stop valves, cast copper alloy , fancy type, chromium plated, screwed down, high pressure with long shank and cup (concealed type), screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.

Supply and Fix, pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, 15 mm bore, including taking down existing unserviceable one complete all as specified and directed.

Supply and Fix, brass CP fancy wall mixer with L bends (including provision of O/H shower & hand shower) for mixing hot & cold water screwed down for iron pipe 15 mm bore and fixed, with including hand shower and tube inlcuding taking out unserviceable existing one complete all as specified and directed. (Make Hand shower cat part no. HSH-CHR-1717 and wall mixer cat part no. QQT-7281 of Jaquar or equivalent make Kohler/Marc)

S&F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm as in repair complete all as specified and directed.

Supply and Fix, in repair kitchen dish rack made of stainless steel sheet,1.00 mm thick, overall size 600 mm (H) x 600 mm (W) X 250 mm (D), complete all as specified and directed.

S&F vitreous chaina wash hand basin 550x400mm (flat back type) including cutting for and pinning in ends of brackets with and including waste fittings, CP pillar tap with capstan head, and waste water pipe complite all as specified and as directed.

Supply and Fix vitreous China Squatting pan ‘Orissa’ pattern, size 580 X 440 mm, white, with integral foot rests and with ‘P’ or ‘S” trap, (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and including provision of lime concrete bedding, complete all as specified and directed. (Make Cat part no.20042 of Hindware or equivalent make of parryware/Cera

Supply and Fix in repair PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle, of capacity 10 Litres, including brackets, flush pipe, complete all as specified and directed.

Supply and Fix, in repair soap dish, fixed in wall, complete all as specified and directed.Make Catpart no.AQN-7731 of Jaquar or equivalent make of Kohler/Marc

Supply and Fix, waste coupling of PTMT (half or full threaded) (Minimum weight 45gms), for 32 mm bore discharge pipe,complete all as specified and directed.

Supply and fix PVC connections 15 mm size with PTMT nuts of length 450 mm,complete all as specified and directed.

S&F PVC waste pipe 32mm dia 800mm long with socket sutable for WHB/Sink complete all as directed

Supply and fix, as in repairs, grating square 150 mm size of PTMT with grating square fitting of size 150 mm made in two part for smell and mosquito proofing with minimum 25 mm water seal of PTMT (Minimum weight 85 gms) all as specified and directed.

Supply and Fix, in repairs 110 mm bore UPVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

Supply and Fix, in repairs 110 mm bore UPVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in treches or in floor , complete all as specified and directed.

Supply and Fix, 110 mm bore PVC (SWR) bends any radius,with oval access door,complete all as specified and directed.

Supply and Fix, 75 mm bore PVC (SWR) bends any radius,with oval access door,complete all as specified and directed.

Supply and Fix, in repairs PVC (SWR) floor trap, plain with grating including jointing with solvent cement with dia. of out let 75 mm, complete all as specified and directed.

Supply and Fix, PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete all as specified and directed.

S&F 110mm dia PVC(SWR) junction single, (single T) equal or unequal with access door complete all as specified and as directed.

Supply and Fix, brass chromium plated shower rose 125mm size,with swivel joints, fixed to steel pipe or union 15 mm bore, including 460mm long CP arm complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down copper/aluminium sub main wiring complete and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for concealed type wiring using approved colour coding as per IS for one light/ fan/ bell point controlled by one switch with1.5 Sqmm (Nominal area) PVC insulated, unsheathed, multistranded copper, conductor cable FRLSH (1100Volts grade) drawn in and including PVC rigid conduits of 20/25 mm dia with all fittings and accessories alongwith PVC insulated standard copper conductor of size 1.5 Sqmm as earth continuity conductor including fixing of 1. 22mm thick MS sunk terminal box duly flushed to wall with 3mm thick plastic laminated/ebonite sheet cover fixed with brass screws,cap and washers complete all as specified and as directed. Note:- (i) The chases in the wall shall be cut with elect cutter (ii) The disturbed surfaces of wall shall be made good with cement plaster 1:4 including matching the surfaces with as per existing finishes and to the entire satisfaction of Engineer in Charge

All as per item No-136 as above but for one 3/5 pin socket outlet 5 Amps on the same board with other switches.

All as per item No-136 here-in-before but for switch socket combination 5 Amps 2/3/5 Pin point on independent board.

All as per item No-136 here-in-before but for switch socket combination 15 Amps 3/6 Pin on independent board with 2.5 Sqmm (Nominal area) PVC insulated unsheathed, multistranded copper conductor FRLSH cable (1100Volts grade) complete.

M & L wiring for circuit/Sub main wiring concealed type with two single core cable PVC insulated cable with 4.00 Sqmm (Nominal area) multi stranded copper conductor FRLSH cable 1100 volts grade including earth continuity conductor using PVC insulated cable of stranded copper conductor of size 2.5 Sqmm connected to common earth dolly and drawing into and including steel conduits of size 20/25 mm dia medium grade including making good the disturbed surfaces to match with existing surfaces complete all as specified and as directed.

Supply and Fix, switch piano, flush button, single pole, one way, 5 Amps, complete all as specified and directed.

Supply and Fix, bell push, flush type, 5 Amps, complete all as specified and directed.

Supply and Fix, ceiling rose, three terminal, PVC/ Polycarbonate insulated body, complete all as specified and directed.

Supply and Fix stepped type electronic fan regulator, flush type, on existing phenolic laminated sheet etc. as required , complete all as specified and directed.

Supply and Fix lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings,complete all as specified and directed.

Supply and Fix, switch socket combination, 2 in 1, 5 Amp, flush type , complete all as specified and directed.

Supply and Fix, switch socket combination 2 in 1, 5 pin, 15 Amp, flush type universal, complete all as specified and directed.

M&L for Ding dong bell, AC, 240Volts, complete all as directed. (Make - Anchor Cat No 46090 / Gold Medal, Ding Dong Door bell Cat No 203048).

Supply and Fix,decorative wall light fixture made up of polycarbonate, suitable for 10/15 W retrofit LED lamp (Spiral B-22 base), all as per Cat No LHDL02160099 ‘CITY1 NEW’ of Make “Havells” or equivalent Model of Make ‘Bajaj/Philips including LED lamp, 10 Watts, lumen output 1100 lm, colour temp 6500 K, lamp current 0.055 amp, lamp base cap B22,, complete all as specified and directed.

Supply and Fix, LED tube light fitting, 20 Watts, lumen output 2000 lm, colour temp 6500 K, lamp base cap G13, all as per Cat No. LHLDDBXEML6X020 of Make ‘Havells’ or Equivalent Model of Make Bajaj/Philips and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet, complete all as specified and directed.

S & F 25 Watt 230 volt 50 Hz LED type new generation energy saving building security light luminiries housing is of versatile pressure die cast aluminium IP 66 with high power LED light complete with suitable capacity integrated electronic driver including of all accessories prewired including connecting up with 2.5 sqmm multi stranded aluminium conductor 2 core cables not less than 2 m of length fixed to pole/wall etc and testing with and including 1.5mtr GI pipe 40mm dia light grade bracket bend to shape ,clamps,nuts,bolts and washer complete all as specified and directed. Make: Wipro/philips/CG.

Supply and Fix, double door, sheet metal enclosure for DBs rating IK09 ,IP42 for mounting of MCB for 240 Volts, 4 way, with 200 Amps rated bus bar, Single Pole & Neutral, including dismantling taking down unserv. DB complete all as specified and directed. [ Make L&T / Legrand/Siemens]

Supply and Fix, double door, sheet metal enclosure for DBs for mounting of MCB for 415 Volts, 8 way, with 200 Amps rated bus bar, Triple Pole & Neutral, including dismantling taking down unserv. DB complete all as specified and directed [ L&T / Legrand/Siemens]

Supply and Fix, miniature circuit breaker (MCBs), single pole, 240 Volts,10KA, 6-32 Amps C series complete all as specified and directed.

Supply and Fix, miniature circuit breaker (MCBs), single pole and neutral, 240 Volts,10KA, 40 Amps "C" series complete all as specified and directed.

Supply and Fix, miniature circuit breaker (MCBs) three pole and neutral, 415 Volts, 10KA, 63 Amps complete all as specified and directed.

Supply,laying, jointing and testing of LT, XLPE insulated, PVC sheathed, armoured, heavy duty electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 25 sq. mm, 3 ½ core, including with suitable size of lugs including taking out existing one complete all as specified and directed.

Materials and Labour for earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanised steel earth lead wire 4 mm dia. by means of bolts, nuts check nuts and washers of galvanised steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia. MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown on electrical plate No 3 of SSR Part –I (2009)

A M CHOUDHURY AND CO

M/S RK SAHA AND CO

M/S N M TRADERS