For Providing Electrification Work 1st Call. P. A. C. 2807367.00 on Electrical SOR 01-01-2024, Completion period 365 Days (i/c rainy season)

For Providing Electrification Work for RR/SR/ Deposit/MOW /OW in Non Residential Building Kanha Guest House, Kshipra Guest House at (Section Lok Bhawan) Under PWD E/M Sub Division M-1, Bhopal. (Detail Schedule Attached)

SECTION 4

BILL OF QUANTITIES (BOQ)

General Description of work: For Providing Electrification Work for RR/SR/ Deposit/MOW /OW in Non Residential Building Kanha Guest House, Kshipra Guest House at (Section Lok Bhawan) Under PWD E/M Sub Division M-1, Bhopal. 1st Call. P. A. C. 2807367.00 on Electrical SOR 01-01-2024, Completion period 365 Days (i/c rainy season)

Probable Amount of Contract :

(Rs. In Figure) :-

(Rs. In Words) :-

SOR.No

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size and 1.5sq. mm. PVC FRLS insulated copper earth continuity conductor of green colour inside conduit etc. as required as per specification for :-

Light point/fan points.

Primary short point

Primary medium point

Primary long point

(Light point/fan points) looping point

Secondary short point

Secondary medium point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Twin control light points

Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets) for 3 pin 6 Amp. Socket outlet point with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit with required materials as per specification on same board.

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size and 1.5sq. mm. PVC FRLS insulated copper earth continuity conductor of green colour inside conduit etc. as required as per specification for :-

Light point/fan points.

Primary short point

Primary medium point

Primary long point

(Light point/fan points) looping point

Secondary short point

Secondary medium point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Twin control light points

Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets) for 3 pin 6 Amp. Socket outlet point with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit with required materials as per specification on same board.

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints etc. as required as per specification for :-

Light point/fan points.

Primary short point

Primary medium point

Primary long point

(Light point/fan points) looping point

Secondary short point

Secondary medium point

Secondary long point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Medium point

Long point

Twin control light points

Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets) for 3 pin 6 Amp. socket outlet point with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size and 1.5sq. mm. PVC insulated copper earth continuity conductor of green colour inside conduit with required materials as per specification on same board.

Wiring for circuit wiring with PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) of ISI marked suitable size etc. as required as per specification

2x2.5 Sq.mm.

4x2.5 Sq.mm.

6x2.5 Sq.mm.

8x2.5 Sq.mm.

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in Surface rigid P.V.C. casing and caping ISI marked of suitable size and 1.5sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside casing & capping screwless connector for joints etc. as required as per specification for :-

Light point/fan points.

Primary short point

Primary medium point

Primary long point

(Light point/fan points) looping point

Secondary short point

Secondary medium point

Secondary long point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Twin control light points

Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets) for 3 pin 6 Amp. socket outlet point with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in Surface rigid P.V.C. casing and caping ISI marked of suitable size and 1.5sq. mm. PVC insulated copper earth continuity conductor of green colour inside casing & capping with required materials as per specification on same board.

Wiring for circuit wiring with PVC insulated cable FRLS with copper multi strand conductor ISI marked in Surface rigid P.V.C. casing and caping of ISI marked suitable size etc. as required as per specification

2x2.5 Sq.mm.

4x2.5 Sq.mm.

6x2.5 Sq.mm.

8x2.5 Sq.mm.

Point wiring (excluding metallic switch box & sheet) for 3 Pin 16 Amp. socket outlet point with 4sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size etc. with 20/16 Amp. F.T. switch & socket/S.S. combined 20/16/6 Amp. of ISI marked and 4sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints as per specification for :-

On separate board

Short point

Medium point

Long point

Extra long -I

Extra long -II

Extra long -III

Same board switch & socket 16 Amp./S.S. combined 20/16/6 Amp

Point wiring (excluding metallic switch box & sheet) for 3 Pin 16 Amp. socket outlet point with 4sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size etc. with 20/16 Amp. F.T. switch & socket/S.S. combined 20/16/6 Amp. of ISI marked and 4sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints as per specification for :-

On separate board

Short point

Medium point

Long point

Extra long -I

Extra long -II

Extra long -III

Same board switch & socket 16 Amp./S.S. combined 20/16/6 Amp

Point wiring (excluding metallic switch box & sheet) for 3 Pin 16 Amp. socket outlet point with 4sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) ISI marked of suitable size etc. with 20/16 Amp. F.T. switch & socket/S.S. combined 20/16/6 Amp. of ISI marked and 4sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints as per specification for :-

On separate board

Short point

Medium point

Long point

Extra long-I

Extra long-II

Extra long-III

Same board switch & socket 16 Amp./S.S. combined 20/16/6 Amp

Point wiring (excluding metallic switch box & sheet) for 3 Pin 16 Amp. socket outlet point with 4sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. casing and caping ISI marked of suitable size etc. with 20/16 Amp. F.T. switch & socket/S.S. combined 20/16/6 Amp. of ISI marked and 4sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside capping, screwless connector for joints as per specification for :-

On separate board

Short point

Medium point

Long point

Extra long-I

Extra long-II

Extra long-III

Same board switch & socket 16 Amp./S.S. combined 20/16/6 Amp

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in existing concealed rigid conduit ISI marked of suitable size with PVC insulated FRLS copper earth continuity conductor of green colour, screwless connector for joints as per specification including earthing of regulator etc as required for :-

Light point/fan/ex-fan points.

Short point

Medium point

Long point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable copper stranded conductor ISI marked FRLS in existing surface rigid conduit ISI marked of suitable size with PVC insulated FRLS copper earth continuity conductor of green colour as per specification including earthing of regulator etc as required for :-

Light point/fan /ex-fan points.

Short point

Medium point

Long point

3 Pin 6 Amp socket outlet on separate board

Short point

Medium point

Long point

Call bell/buzzer points

Short point

Medium point

Long point

Supplying and fixing PVC conduit ISI marked FRLS along with accessories on surface etc. as required

PVC conduit 20 mm. (MMS)

PVC conduit 25 mm. (MMS)

PVC conduit 32 mm. (MMS)

Supply and fixing PVC conduit ISI marked FRLS along with the accessories in concealed system etc. as required

PVC. conduit 20 mm (HMS)

PVC. conduit 25 mm (HMS)

Supplying and fixing PVC casing and capping (double fold) ISI marked along with accessories on surface etc. as required

PVC casing and capping (double fold) 20 mm x 12mm

PVC casing and capping (double fold) 25 mm x 12mm

Supplying and fixing factory fabricated hot dip galvanized switch box for normal flush type accessories of minimum 1.2 mm thickness for up to 200mmx250mm size boxes and 1.6mm minimum thickness for higher size boxes, earth terminal stud with nut and washer, including 3 mm thick synthetic phenolic resin bonded laminated sheet conforming to grade P-I of IS:2036-1974 on surface/concealed including all necessary accessories, painting etc. as required as per specification:

MS box 100 mm X 100 mm X 60mm

MS box 200 mm X 150 mm X 60 mm

MS box 180 mm X 100 mm X 60 mm

MS box 125 mm X 300 mm X 60 mm

MS box 200 mm X 250 mm X 60 mm

MS box 250 mm X 300 mm X 60 mm

MS box 300mm X 380 mm X 60 mm

Supplying and fixing of approved make modular type G.I. metal box 1.2mm minimum thick and depth 50mm for single row boxes and 60mm depth for two/three row boxes earth terminal stud with nut and washer with modular base and cover plate including fixing in concealed etc. as required for:-

1Or 2 Module metal box

3 Module metal box

6 Module metal box

8/9 Module metal box

12 Module metal box

16 Module metal box

18 Module metal box

Supplying and fixing of approved make modular type PVC box minimum depth 40mm and minimum thickness 2mm with modular base and cover plate including fixing on surface etc. as required for:-

1 Or 2 Module PVC box

3 Module PVC box

6 Module PVC box

8/9 Module PVC box

12 Module PVC box

Supplying and drawing single core PVC insulated cable FRLS with copper multi strand conductor ISI marked in existing rigid PVC casing and capping/conduit in surface or concealed as per specification.

1.5 sq. mm. wire

1 X 1.5 sq. mm.

2 X 1.5 sq. mm.

3 X 1.5 sq. mm.

2.5 sq. mm. wire

1 X 2.5 sq. mm.

2 X 2.5 sq. mm.

3 X 2.5 sq. mm.

4.00 sq. mm. wire

1 X 4.00 sq. mm.

2 X 4.00 sq. mm.

3 X 4.00 sq. mm.

6.00 sq. mm. wire

1 X 6.00 sq. mm.

10.00 sq. mm. cable

1 X 10.00 sq. mm.

16.00 sq. mm. cable

1 X 16.00 sq. mm.

Supply of ISI Marked On-Load Change over switches panel mouniting type confirming to IS : 13947 (part I & III ) with front operated 4 pole, 415 V with two earthing terminals if required.

Supply of ISI Marked Switch Disconnector Fuse (SDF), in sheet steel enclosure (Panel mounting cubicle type) confirming to IS:13947 (part I & III ) 3 pole and neutral , AC -23A ,50 Hz , 415 Volt with 3 HBC fuses complete.

Supply of ISI Marked Direct On-Line Starters confirming to IS : 13947-4 with suitable over load relay range and contactor size, 415 V , 3 -Phase with two earthing terminals

Supply & fixing of High Breaking Capacity (HBC) Fuse Links bolted connection type as per IS : 13703 : 1993 & IEC : 60269 :1986 with 80 kA breaking capacity of approved make

80 Amp to 125 Amp

160 Amp to 250 Amp

Supply & fixing of High Breaking Capacity (HBC) Fuse Links knife (DIN) type as per IS : 13703 : 1993 & IEC : 60269 :1986 with 80 kA breaking capacity of approved make

20 Amp. to 100 Amp

125 Amp to 160 Amp

200 Amp to 315 Amp

Supply & fixing of I.S.I.marked Porecelain Rewireable fuse unit of approved make or confirming to I.S.S. 2086-1982

32 Amps /415 Volts

63 Amps /415 Volts

100 Amps /415 Volts

Supplying of metal clad ISI marked busbar chamber made of heavy gauge iron sheet complete with copper strip and busbar supports as per specification conforming to IS -4064

60/63 Amp 415 VOLTS, 4 way

100 Amp 415 VOLTS, 4 way

200 Amp 415 VOLTS, 4 way

Supply of ISI marked and approved make of moulded case circuit breaker (MCCB) suitable for 3 phase,3 pole, 50 Hz, 415 Volts, AC supply with respective interrupting capacity (KA) at 415 Volts cited against their range standard conforming to IS – 8828

Supplying of ISI marked and approved make of moulded case circuit breaker (MCCB) suitable for 3 phase,3 pole, 50 Hz, 415 Volts, (Ics=100%Icu) AC supply with thermal - magnetic release having respective breaking capacity (KA) at 415 Volts cited against their range standard conforming to IS/IEC 60947-2

Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'C' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10 kA/15 kA Value AC supply conforming to IS : 8828 : 1996, IEC : 60898 :2002 & 60947-2 but without enclosures :-

Single pole

MCB SP 0.5Amp to 5Amp 10kA rating

MCB SP 6Amp to 32Amp 10kA rating

Double pole

MCB DP 6Amp to 32Amp 10kA rating

MCB DP For 40Amp 10kA rating

MCB DP 50Amp to 63Amp 10kA rating

For Triple pole

MCB TP 6Amp to 32Amp 10kA rating

MCB TP For 40Amp 10kA rating

MCB TP 50Amp to 63Amp 10kA rating

Four pole

MCB FP 6Amp to 32Amp 10kA rating

MCB FP For 40Amp 10kA rating

MCB FP 50Amp to 63 Amp 10kA rating

Supply of approved make powder coated sheet steel encloser SPN MCB DB inclusive of busbar, neutral bar, earth bar, connection copper wire not less than 16 sq.mm & two earth terminals etc. complete as per IS:13032(exclusive of MCB & isolator)-

4 Way double door IP 43 protection

6 Way double door IP 43 protection

8 Way double door IP 43 protection

12 Way double door IP 43 protection

Supplying of approved make TPN MCB DB metal double door IP 43 protection with provision for FP MCB/ Isolator/ RCCB/ RCBO as incomer and SP MCBs as outgoing inclusive of busbar, neutral bar, earth bar, connection copper wire not less than 16 sq.mm & two earth terminals etc. complete as per IS:13032(exclusive of MCB & isolator):

Supplying of approved make, powder coated metal double door vertical TPN MCB DB IP 43 protection with provision for MCCB upto160A TP/FP 36kA as incomer and space for SP/TP MCBs as outgoing (without MCCB/MCBs) inclusive of busbar & connections etc

4 Way without MCCB

6 Way without MCCB

Supplying & fixing of approved make Industrial type metal plug & socket DBs (without MCB) SPN sheet encloser (dust protected) inclusive of 2 pole and earth metal plug and socket and space to incorporate SP MCB complete as per specification as required.

Supply & fixing of approved make Industrial type metal plug & socket, 3 pin (2P + E) conforming to IEC : 60309 -1&3 complete as per specification

20Amp Plug only

20Amp socket only

Supplying and installing of RCBOs (Residual current circuit breaker with overload and short circuit protection) ISI marked complete as per I.S. standard conforming to IEC:61009-1 & IS:12640-2, 240/415V 50 Hz with 10 kA short circuit withstand capacity for earth leakage, overload & short circuit protection including connection in existing enclosure in approved manner as per specification.

DP (4 module)

2 pole 40Amp, 30mA sensitivity

FP (8module)

4 pole 40Amp, 30mA sensitivity

4 pole 63Amp, 30mA sensitivity

Fixing of MCB/MCCB/Isolator in sheet steel enclosure as required as per accepted practice, including mounting on busbar and cable connection etc. complete (labour only)

MCB/Isolator SP/DP

MCB/MCCB Isolator TP/TPN/FP

Labour charges for fixing sheet steel enclosure, MCB DB surface mounting type, as per accepted practice on 25x5mm flat iron clamp duly embedded in wall, cable connection etc. complete.

For item no :-

Labour charges for fixing sheet steel enclosures, MCB DB surface mounting type, as per accepted practice on 25x25x 5 mm angle iron clamp, including supplying and fixing of clamp duly embedded in wall, cable connection etc. complete :-

For item no :-

27.11.6 & 27.11.7; 27.12.5 ; 27.13.2 to 27.13.4 & 27.14.1 to 27.14.4 ; 27.15.1 to 27.15.4

Labour charges for fixing sheet steel enclosures, MCCB DB surface mounting type, as per accepted practice on 35x35x 5 mm angle iron clamp, including supplying and fixing of clamp duly embedded in wall, cable connection etc. complete :-

Labour charges for fixing sheet steel enclosures, MCB/MCCBDB flush mounting type, as per accepted practice, duly embedded and end plate completely flushed in wall, cable connection etc. complete :-

For item no :-

27.12.4 & 27.12.5 ; 27.13.2 to 27.13.4 ; 27.14.1 to 27.14.4 & 27.15.1 to 27.15.4

Supply and fixing as per specification pendent holder of approved make including flexible cord up to 3 metre length with necessary materials complete

Supply and fixing as per specification polycarbonate batten holder/angle holder of approved make with necessary materials complete

Supply and fixing as per specification call bell/buzzer of approved make with necessary materials complete.

Gong bell

Buzzer

Ding dong bell

Multi sound bell

Remote/cordless bell

Supply and fixing as per specification modular call bell indicator 230Volt A.C. including reset and buzzer of approved make with necessary materials complete.

Bell indicator with reset(1 Module) 250Volt

Supply and fixing of multi core round FRLSH PVC insulated copper (flexible) conductor & PVC sheathed cables 1100Volts as per IS:694-1990 of approved make

(16/0.2 mm)Three core 0.5 sq.mm.

(30/0.25 mm) Three core 1.5 sq.mm.

(50/0.25 mm) Three core 2.5 sq.mm.

(56/0.3 mm) Three core 4.0 sq.mm.

Supply and fixing in position LED lamp of approved make

3 Watt250Volt

5 Watt250Volt

9 Watt250Volt

15 Watt250Volt

18 Watt250Volt

Supply and fixing as per specification Switch of approved make ISI marked with necessary material complete.

6Amp SP 250 Volt deluxe (piano key type)

16/20Amp SP 250 Volt deluxe (piano key type)

6Amp SP 250 Volt two way F/T

6/10Amp SP 250 Volt modular switch

16/20Amp SP 250 Volt modular switch

10Amp SP 250 Volt modular switch 2 way

32 Amps D.P.250 Volt modular switch with indicator LED 2 Module

Blank plate 1 module

Surface switch 6Amp

Supply and fixing as per specification socket outlet of approved make & ISI marked with necessary material complete

6Amp 250 Volt 3 Pin flush type

16Amp 250 Volt 3 Pin flush type

10Amp 250 Volt 3 Pin modular type

10/16/20Amp 250 Volt 3 Pin modular type

Supply and fixing as per specification switch socket combined of approved make & ISI marked with necessary material complete

20/10Amp 250Volt 3/6 Pin flush type

Supply and fixing as per specification polycarbonate ceiling rose 3 plate of approved make ISI marked with necessary material complete.

Supply and fixing of approved make 3 pin plug top ISI marked

6Amp 250Volt 3 Pin top

16Amp 250Volt 3 Pin top

Supply and fixing of MPP condenser 440 Volt single phase of approved make as required as per specification

Condenser 2.5 mfd 440Volt

Condenser 3.15 mfd 440Volt

Condenser 4.00 mfd 440Volt

Supply and fixing of MPP condenser 250Volt single phase of approved make as required as per specification

Condenser 4 mfd 250Volt

Condenser 8 mfd 250Volt

Condenser 10 mfd 250Volt

Condenser 15 mfd 250Volt

Supply and fixing of ball bearing of approved make as required as per specification

Supply and fixing of approved make flush type step type electronic fan regulator including connection etc. as required on existing board

Supply and fixing of approved make electronic dimmer/regulator including connection etc. as required on existing board

Supply and fixing of approved make step type modular electronic fan regulator including connection etc. as required on existing board

100 Watt (1 module)

100 Watt(2 module)

Supply and fixing of LT panel accessories of approved make in existing LT panel including connections etc. as required as per specification.

Frequency Metre

Supplying, erection and testing of approved make electric Ceiling fan of double ball bearing complete with standard down rod, canopy, hanging shackle, Aluminium blades, without regulator, A.C. 230-250 volts including connections with all necessary material complete of approved as required confirming to IS :374/2019 with upto date amendments.

Ceiling fan - 900 mm sweep

Ceiling Fan (ISI marked)-1200 mm Sweep, with minimum air delivery 210 m³/min and service value ≥ 4.00 as per BEE..

Ceiling Fan ( ISI marked )-1400 mm Sweep, minimum air delivery 245 m³/min and service value ≥ 4.10 as per BEE.

Supplying, erection and testing of approved make wall mounting fan oscillating type with base, blades, guard, speed regulator etc. AC 230-250 volts with connections and including raw bolt/anchor hole fastener etc. complete finished and as required.

300 mm sweep

400 mm sweep

Supplying, erection and testing of approved make cabin fan oscillating type with base, blades, guard, speed regulator etc. AC 230-250 volts with connections and including raw bolt/anchor hole fastener etc. complete finished and as required.

300 mm sweep

Supplying, erection and testing of approved make 'Fresh air fan' AC 230-250 volts with connection and including frame bolt/anchor hole fasteners etc. complete finished and as required.

150 mm sweep bush type

225 mm sweep double ball bearing

300 mm sweep double ball bearing

Supplying and fixing of deluxe fresh air fan with louvers (ventilating fan) with self-closing louvers of decorative PVC blades mounting square frame of approved make complete with all necessary material as required

200mm RPM1300/1400

250mm RPM1300/1400

Supplying, erecting and testing of approved make exhaust fan heavy duty with mounting frame, blades AC 230-250 complete connection and including, frame bolt/anchor hole fasteners etc. complete finished and as required.

300mm sweep RPM 900 / 1400

450mm sweep RPM 900 / 1400

Supplying and testing of approved make Pedestal fan A.C. 230-250 volts with blades speed regulator 'pedestal etc duly wired with all necessary material complete as required

400 mm Sweep

Supplying, erection and testing of approved make air circulator fan A.C. 230-250 volts with blades speed regulator etc duly wired with all necessary material complete as required

Air circulator wall mounting fan

450 mm sweep

Supplying and replacement of cooler fan 500 mm (20") ISI marked with all necessary material including connection complete of approved as required

Supply and replacement of ISI marked cooler submersible water pump complete with all necessary material including connection of approved make as required

Supplying and fixing of cooler/A.C. M.S. angle iron stand including flat iron supports, grouting in wall if required, welding, painting with primer and two coat of superior quality paint complete.

Supply and fixing M.S. down rod 14 SWG (2mm) thick for ceiling fan including threading, painting, making holes etc. as required complete. Note: For new works difference of installed & standard down rod length shall be paid.

Supply, fixing & testing of approved make globe type polycarbonate post top lantern, consisting of cast aluminium spigot complete with all accessories, lamp holder, (without lamp) including fixing on gate pillars/exiting G.I. pipe, pole with connection & all required materials on existing required size of G.I. pipe, suitable for CFL/LED lamp for mentioned below sizes :-

Supply and fixing Led tube rod comprising of LED tube with non- integral/integral driver, upto 6500K color temp having 40000 burning hrs life with minimum @ L 70, system lumen output should be minimum with system efficacy> 100 lm/Watt. LED driver PF> 0.95 & THD < 20%. The colour rendering index of LED light should be more than 70. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.

Tube light LED 1 X 8/10Watt Integral i/c batten aluminium body, PC diffuser.

Tube light LED 1 X 18Watt, Integral i/c batten aluminium body, PC diffuser.

Tube light LED 1 X 20/22Watt, Integral i/c batten aluminium body, PC diffuser.

LED retrofit glass tube i/c driver only 20/22Watt,color temp 3000 - 6000K without box suitable for replacing existing 36/40Watt FTL

Supply and fixing of recessed mounting type Led light fixture, LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver PF> 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.

LED luminiare 2' X 2', 36Watt, color temp 3000-6500k as required.

LED luminiare 2' X 2', 42/45Watt, color temp 3000-6500k as required.

Supply and fixing of surface mounting type LED light fixture, LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs. life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver, PF> 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.

LED luminiare 2' X 2', 36Watt, color temp 3000-6500k as required.

Supply and fixing recessed mounting LED down lighter, LED of 1 to 3 Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs. life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver PF > 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of pressure die cast aluminium/CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79- 08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job..

3 Watt, color temp 3000-6500k as required.

5/6 Watt, color temp 3000-6500k as required.

12 Watt, color temp 3000-6500k as required.

14/15 Watt, color temp 3000-6500k as required.

18/20Watt, color temp 3000-6500k as required.

22/24Watt, color temp 3000-6500k as required.

Supply and fixing surface mounting LED down lighter, LED of 1 to 3Watt each assembled on single MCPCB, having color temp upto 6500K & having 50000 burning hrs. life with minimum @ L 70, system lumen output should be minimum with efficacy>100 lm/Watt. LED driver PF > 0.95, THD < 20% & surge protection 4KV. The colour rendering index of LED light should be more than 70. Housing made of pressure die cast aluminium/CRCA powder coated frame with glare free diffused polycarbonate cover. Submission LM 79- 08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job..

14/15 Watt, color temp 3000-6500k as required.

18/20 Watt, color temp 3000-6500k as required.

21/22/24Watt, color temp 3000-6500k as required.

Supply and fixing of recessed mounting LED swivel type COB downlighter, having color temp upto 6500K & having 20000 burning hrs life with minimum @ L 70, system lumen output should be minimum with efficacy>80lm/W. LED driver PF > 0.9, THD < 20% & surge protection 5KV. The colour rendering index of LED light should be more than 70. Housing made of pressure die cast aluminium / CRCA powder coated frame with glare free diffused polycorbonate cover. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106 from NABL approved lab. Manufacturer manadatory. i/c connection wire, testing etc. to complete the job. Guarantee as per tender agreement condition.

Supply and fixing of Linear profile suspended LED lumanaire, having color temp upto 6500K & having 20000 burning hrs life with minimum @ L 70, system lumen output should be minimum with efficacy>80lm/W. LED driver PF > 0.9, THD < 20% & surge protection 5KV. The colour rendering index of LED light should be more than 80. Housing made of pressure die cast aluminium / CRCA powder coated frame with high transmission diffuser. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106 from NABL approved lab. Manufacturer manadatory. i/c mounting arrangment, connection wire, testing etc. to complete the job. Guarantee as per tender agreement condition.

Supply and fixing street light with high power LED of 3 to 6 Watt each on existing bracket assembled on single MCPCB and additional unique peanut lens on each LED, system lumens output with efficacy>120 lm/Watt. luminiare having color temp upto 6500K & 50000 hrs. burning life with minimum @ L 70, The colour rendering index of LED light should be more than 70. Luminiare comprises of driver, PF> 0.95 & surge protection 10KV. Housing made of pressure die cast aluminium with heat resistant flat glass, IP65 protection. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347 i/c connection wire, testing etc. to complete the job.

40Watt to 48Watt, color temp 3000-6500k as required.

60Watt, color temp 3000-6500k as required.

90Watt, color temp 3000-6500k as required.

120Watt, color temp 3000-6500k as required.

Supplying and fixing flood light with high power LED of 3 to 6 Watt each assembled on single MCPCB and additional unique peanut lens on each LED, system lumens output with efficacy>120 lm/Watt. luminiare having color temp upto 6500K & 50000 hrs. burning life with minimum @ L 70, The colour rendering index of LED light should be more than 70. Luminiare comprises of driver, PF > 0.95 & surge protection 10KV. Housing made of pressure die cast aluminium with heat resistant flat glass, IP65 protection. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.

60Watt, color temp 3000-6500k as required.

90/100Watt, color temp 3000-6500k as required.

Supplying, fixing & testing of approved make flexible LED strip comprising of 60 LED per meter W/O driver for direct mounting complete with all accessories including connection lead, fixing, connection as required. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire, testing etc. to complete the job.

Flexible LED strip 24Watt/25Watt - 5 M indoor cove light W/O Driver IP 20 -33

Flexible LED strip 24Watt/25Watt - 5 M outdoor cove light W/O driver IP65

Supplying, fixing & testing of approved make Power supply for LED strip

Power supply 25Watt/30Watt for LED strip IP25/IP33

Power supply 48Watt for LED strip IP33

Power supply 25Watt/30Watt for LED strip IP65

Power supply 48Watt for LED strip IP65

Supplying Fixing and testing of approved and suitable make LED driver for an existing LED luminary panel.

LED Luminiare 1'x1', 24W Panel Driver

LED Luminiare 2'x2', 36W Panel Driver

Supplying fixing and testing of approved and suitable make LED driver for an existing LED street light.

24Watt to 25Watt, color temp 3000-6500k

40Watt to 48Watt, color temp 3000-6500k

60Watt, color temp 3000-6500k

90Watt, color temp 3000-6500k

120Watt, color temp 3000-6500k

Supplying, fixing and testing of approved and suitable make LED driver for an existing LED Flood light.

60Watt, color temp 3000-6500k

90Watt, color temp 3000-6500k

Fixing of fluorescent tube fitting with pendent arrangement of two pieces of approved chrome plated metallic chain with necessary material including connection 3 core flexible wire etc. complete as required.

For pendent length upto 1.5 Metre

Add additional pendent length in excess of 1.5 Metre

Providing and fixing circular/hexagonal cast iron or M.S. sheet box for ceiling fan clamp of internal dia 140mm, 73mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/M.S. sheet box by mean of 3.3mm dia. round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape as per standard drawing.

Supplying and fixing fan clamp of 12 mm dia steel bar as per specification complete.

For stone slab roof "J" Type hook

For R.C.C. slabs/beams

For existing R.C.C. slabs/beams

Erection of ceiling fan in position with regulator on existing switch board including wiring, testing etc. with necessary material complete as required.

Erection of fan regulator in position with necessary material connection etc. complete as required.

Erection of exhaust fan in position with required PVC sheathed cable, frame bolts etc. complete including connections.

Numbering of ceiling fans or fitting with approved paint including all labour material etc. as required.

Letter upto 5 CM height

Letter above 7 CM but upto 15 CM height

Providing and fixing T.W. board of suitable size (maximum 12" X 18") for fixing of house service Metre with necessary materials and connection testing etc. complete as per specification :

Single phase Metre

Three phase Metre

Providing & fixing of wood wool/khas pads of normal size desert/room cooler panels set of 3 nos including fixing wire mesh on pads.

Servicing & overhauling of cooler fan motor, pump including replacement of distribution, delivery pipes, PVC elbows, painting etc. as reqd. complete with necessary material & labour.

Rewinding of fans by copper enameled wire of suitable gauge including all required material, insulation, varnishing, connection leads, oiling .greasing etc complete with testing including dismantling & refitting of fan at site. Scrap old material is not returnable to the department.

Ceiling fan 1400 mm sweep old model/exhaust fan 450 mm sweep

Ceiling fan 1400 mm sweep new model/exhaust fan 380 mm sweep

Ceiling fan 1200 mm sweep old model/cooler fan 500 mm (20")sweep

Ceiling fan 1200 mm sweep new model/exhaust fan 300 mm sweep

Fresh air fan up to 300 mm sweep/wall bracket/cabin fan 400 mm sweep

Cleaning, overhauling, servicing of ceiling/exhaust/wall bracket fan by applying grease & oil, including testing with mounting/hanging arrangement including replacement of safety pins, check nuts, lock nut, nut bolts etc. making perfect alignment & refitting at site as required.

Painting of water cooler including scraping of old paint making surface even, prima paint coat and spray painting of body, etc. with two coat of required shade complete with material and labour.

Painting of poles

Removing of old paint from steel and other metallic surface and making surface even.

Prima coat over new steel and other metallic surface with red oxide zinc chromide paint complete with supply of material labour etc. including preparation of surface.

Prima coat with aluminium paint, brushing complete with material and labour including preparation of surface

Dismantling of existing light/fan/ bell/socket out let point on separate board/wiring and circuit with insulated wire in casing/conduit/ batten complete with fitting and accessories

Making the site clear of the dismantled installation by refilling the hole with cement mortar & finished with paint gitties and replacing to match the colour& wall ceiling.

Dismantling of existing socket outlet point on same board in any system of wiring

Dismantling the existing armoured/unarmoured cable or 2/3/4 wires of submain, main, in any system of wiring including recoiling.

Dismantling of existing underground cable safely with its accessories and refilling the trench to ground level including recoiling of dismantled cable.

Dismantling of D.F. board, D.P. switch, T.P. & T.P.N. switch or D.B. of any size only

Dismantling the existing ceiling/exhaust/cabin fan with complete accessories and making the site clear.

Dismantling of existing steel pole, R.S. Joist, girder with bracket clamp insulator or stay from the cement concrete foundation and making the site clear by refilling the pit to ground level i/c transportation to required destination within township.

Providing recess in brick wall suitable for erecting of exhaust fan up to 450 sweep complete with grouting of nut bolts, plastering and colour wash to match the colour of wall.

For wall thickness upto 9"

For wall thickness upto 15"

Earthing with G.I. earth pipe 4.5 metre long and 40 mm dia with masonry encloser in cement mortar, cover plate having locking arrangement on the top etc. (but without charcoal or coke and salt) complete as required

Add extra for using salt and charcoal/coke for pipe earth electrode as required including excavation & refilling

Excavation 4.5 m by manual labour

Excavation by making hole with auger

Earthing with copper earth plate 600mm X 600mm X 3mm thick including accessories and providing masonry encloser in cement mortar, cover plate having locking arrangement on the top and G.I. watering pipe 20mm dia 2.7 metre long etc. (but without charcoal or coke and salt) complete as required

Add extra for using salt and charcoal/coke for G.I. plate or copper plate earth electrode as required including excavation and refilling the pit in all type of soil, murrum

Add extra for using salt and charcoal/coke for G.I. plate or copper plate earth electrode as required including excavation in hard rock and refilling the pit with black soil.

Supply and laying 4mm dia. copper wire at 0.5 metre below ground level as conductor earth electrode including soldering etc. as required.

Supply and laying 4.87mm 6 SWG G.I. wire at 0.5 metre below ground level as conductor earth electrode including jointing etc. as required.

Supply and laying 25mm X 5mm G.I. strip at 0.5 metre below ground level as strip earth electrode including jointing etc. as required.

Supply and erection of approved make safe earthing electrode consisting pipe-in-pipe technology as per IS 3043-1987 made of corrosion free G.I. pipes with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for effective and maintenance free earthing in earth pit of minimum bore dia. 150mm size, as mentioned below :

With 2 metre G.I. pipes having outer pipe dia of 50mm having 80-200 micron galvanizing, Inner pipe dia. of 25mm having 200-250 micron galvanizing, connection terminal dia. of 12mm in nominal soil with 25 kg (one Bag) back filling bentonite compound UL listed and confirm to relevant International/Indian standards around electrode upto ground level.

With 3 metre G.I. pipes having outer pipe dia of 50mm having 80-200 micron galvanizing, Inner pipe dia. of 25mm having 200-250 Micron galvanizing, connection terminal dia. of 12mm in nominal soil with 50 kg (two bag) back filling bentonite compound UL listed and confirm to relevant International/Indian standards around electrode upto ground level.

Providing back filling bentonite compound suitable for safe earthing device. The product should be UL listed and confirm to relevant International/Indian standards.

Supply, installation testing and commissioning RJ - 45 computer jack cat 6 with shutter modular (1Module)

RJ - 45 computer socket cat 6 with shutter modular (1Module)

RJ - 45 computer socket cat 6 tool less connection (1Module)

Supplying and drawing 4 pair un-shielded twisted pair (UTP), 0.5 mm PVC insulated copper conductor un-armoured Cat-6 computer cable FRLS in existing surface/concealed, steel/PVC. conduit/ casing-n-capping as required.

Supplying and drawing 4 pair shielded twisted pair (STP), 0.5 mm PVC insulated copper conductor un-armoured Cat-6 computer cable FRLS in existing surface/concealed, steel/PVC. conduit/ casing-n-capping as required.

Supply of XLPE insulated power cable (conforming IS-7098 Part-I) 1100 Volt grade, 1 core/2 core/3½ core/4 core ISI marked with alu. stranded /solid conductor

Unarmoured 2 core

Armoured 2 core

3½ core armoured

4 core armoured

Brass compression gland

Supplying and fixing heavy duty cable gland for P.V.C. insulated armoured cable with brass washer, rubber ring complete erected with cable and lead connection etc. as per specification complete.

Gland size 32 mm for 2/3, 3½, 4 x 25 sq. mm OR 2/3, 3½ x 35 sq. mm or 2/3/3½ x 50 sq. mm.

Gland size 38 mm 3½ x 70 sq. mm, 3x95 sq. mm

Gland size 45 mm 3/3½ x 120 sq. mm, 3½ x 95 sq. mm, 3 x 150 sq. mm.

Gland size 50 mm ,3½ x 150 sq. mm,3 x 185 sq. mm

Gland size 57 mm, 3 x 225 sq. mm, 3 ½ x 185 sq. mm

Supplying and fixing crimping type alum. lugs as per I.S.S. specification suitable for following size of cable with alu./copper solid/stranded conductor evenly crimped with high/pressure tool and connected to switch gear/bus/M.C.C.B./M.C.B. etc. as required complete.

For conductor size-

6mm to 16 sq. mm

Providing &making cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for 33 KV/11 KV single core XLPE alum. conductor cable as required as per specification and as per accepted standard including connection testing complete.

Heat shrinkable jointing kit 1.1 KV XLPE/HD cable straight through jointing kit (I.D../O.D.)

10-16 sq. mm. 3½/4core

25-50 sq. mm. 3½/4core

70 -150 sq. mm. 3½/4core

Supplying & installing G.I. pipe for protection of underground cable fixed on wall/support/in trench/fixed between two rigid existing support of wall/beam for erection of ceiling Fan/down rod for stiff pendent for light luminaries /fan/protective for earthing, lightening conductor down strip/overhead service line/for submersible cable or centrifugal pump for water supply with necessary iron clamp coupler, bend, tee, elbow, nuts and bolts etc. complete in an approved manner as required to complete excluding cost of excavation/dismantling & other finished masonry Item complete.

For 'B' class pipe ISI marked (IS-1161- 68)

Supplying and installing double wall corrugated pipes (DWC) of HDPE (IS 14930 Part II -marked) for cable laid underground with necessary material and at required depth upto 90cm. below road/ground surface, including excavation, back filling with excavated material, ramming and making the surface good.

50.00mm outside dia.

63.00mm outside dia.

90.00mm outside dia.

110.00mm outside dia.

120.00mm outside dia.

Laying of one number armoured / unarmoured power cable 1.1KV grade of size not exceeding 25 sq. mm direct in ground including excavation in all soil/ murrum /soft rock, sand cushioning, protective covering and refilling the pit etc. as required.

Laying of one number armoured / unarmoured power cable 1.1.KV grade of size exceeding 25sq. mm but not exceeding 120 sq. mm direct in ground including excavation in all soil/ murrum /soft rock, sand cushioning, protective covering and refilling the pit etc. as required.

Laying of one number armoured / unarmoured cable 1.1.KV grade of size exceeding 120 sq. mm. but not exceeding 400 sq. mm direct in ground including excavation in all soil/ murrum /soft rock, and sand cushioning protective covering and refilling the pit etc. as required.

Laying of one number additional armoured / unarmoured power cable 1.1KV grade of size exceeding 25 sq. mm but not exceeding 120 sq. mm direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the pit etc. as required.

Laying of one number armoured / unarmoured power cable 1:1 KV grade of size not exceeding 25 sq. mm in the existing RCC hume/stone ware/G.I. pipe/surface in existing trench as required.

Laying of one number armoured / unarmoured power cable 1.1 KV grade of size exceeding 25 sq. mm but not exceeding 120 sq. mm. in the existing RCC Hume /Stone ware/G.I. Pipe/surface in existing trench as required.

Laying of one number armoured / unarmoured power cable 1.1 KV grade of size exceeding 120 sq. mm but not exceeding 400 sq. mm. in the existing RCC Hume /Stone ware/G.I. Pipe/surface in existing trench as required.

Laying of one number armoured / unarmoured power cable 1.1 KV grade of size not exceeding 25 sq. mm in the existing masonry open duct as required.

Laying of one number armoured/unarmoured power cable 1.1KV grade of size exceeding 25sq. mm but not exceeding 120 sq. mm in the existing masonry open duct as required.

Laying of one number armoured/unarmoured power cable 1.1KV grade of size exceeding 120sq. mm but not exceeding 400 sq. mm in the existing masonry open duct as required.

Laying of one number armoured/unarmoured cable 1.1KV grade of size not exceeding 25 sq. mm on wall/truss with approved type of iron clamp etc. as required.

Laying ofone number armoured/unarmoured cable 1.1KV grade of size exceeding 25 sq. mm but not exceeding 120 sq. mm on wall/truss with approved type of iron clamp etc. as required.

Laying of one number armoured/unarmoured cable 1.1KV grade of size exceeding 120 sq. mm but not exceeding 400 sq. mm on wall/truss with approved type of iron clamp etc. as required.

Supplying and erection of water tight terminal box made of 16 SWG M.S. Sheet (1.6mm thick) i/c rubber gasket of required size suitable for kit kat/MCB/switch including 2 nos. pole clamp of M.S. flat iron size 32x3mm, nut and bolts, 4 Pole epoxy connector nut & bolt type, 30Amp, 500Volt. The box shall be powder coated excluding the cost of the kit kat/MCB/Switch complete as per specification.

20x15x10 Cms.

30x20x10 Cms.

Supplying and fixing of 4 Pole epoxy connector nut & bolt type, 30Amp. 500Volt. in existing box as required as per specification:

Supplying and fixing of hot water storage water heatervertical with required safety, ABS body including connection pipe, foundation bolt and nut, connection pipe, stop cock, testing etc. to complete the job.

15 Ltr. (5 Star rating- standing losses ≤0.419 kWh/24 hrs/45°C)

25 Ltr. (5 Star rating- standing losses ≤0.511 kWh/24 hrs/45°C)

35 Ltr. (5 Star rating- standing losses ≤0.584 kWh/24 hrs/45°C)

Schedule Amount :- Rs.

Executive Engineer PWD E/M Division No. 1, Bhopal