SPL REPAIR TO MOUNTAINEERING STORE ROOM, VIP GUEST ROOM 1 AND 2 AND ADDN/ALTN TO RAIN WATER DRAINAGE SYSTEM FOR GUEST ROOM AT DGNCC UNDER GE (EAST) DELHI CANTT-10

Amount

Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/mumty/parapet and removal of debris and rubbish out side MoD land complete all as specified and directed.

Demolition of brick work built in cement mortar in any description and position complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) including removal of rubbish out side complex (MOD land), complete all as specified and directed.

Dismantling of cupboards 0.60m to 0.80m in depth, made of powder coated aluminium, fixed to wall, including dismantling of sliding shutter of CBs, partitions etc complete all as specified and directed Note :- Only front face area of CBs will measured for payment purpose

Taking down plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed

Dismantling framed iron trusses,not exc 10 mtr in span in any position complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

Taking down chowkhat or frames of any description exc. 1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames) car complete all as specified and directed.

Taking down chowkhat or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down cement plaster, terrazzo, grit plaster dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc. including removal of rubbish, vegetation etc. outside complex (MOD land) complete all as specified and directed.

S&F Aluminium alloy powder coated standard hollow section for ventilators as per approved sample and as per IS specifications, shutters weighting 0.55 kg/RM, rectangular frames of section 101.6mm x 44.45mm x 3.18mm weighing not less than 2.54Kg/RM including provision of 5.5mm thick tinted glass of superior quality including handles, tower bolt, hinges and all standard fittings complete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with 150mm long MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Make 'Rajshree or equivalent as approved by GE"

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including 3 Nos stainless steel butt hinges of size 100mm, 2 Nos 150mm long stainless steel tower bolt and 01 No 250mm long sliding bolt of all as per direction of Engineer-In-Charge.Make 'Rajshree or equivalent as approved by GE "

M & L for fabrication & fixing to horizontal & vertical shelves/ partitions /sides/ top/ bottom/back/ front sides etc. for cabinet/ wardrobe/ cupboard/drawers made out of 17/18 mm thick WPC boards with white/ coloured laminated on both sides, of approved quality including paste to all exposed edge by Banding Tape including provision of drawers etc. complete all as specified and as directed. (Make : Rajshree or equivalent)

M&L for Brick work with sub class 'B' bricks straight or curved on plan to any radius built in CM 1:6 complete all as specified and directed.

All as per Srl item No 15 here-in-before but except bricks.

Providing and injecting chemical emulsion for Post Constructional Anti termite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per Sqm of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed

M&L for injecting chemical emulsion for Post Constructional Anti termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed

M&L for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed

M&L for sand filling under floors or in foundations including watering and consolidation in layers not exc 25cm thick complete all as specified and directed

M&L for 75mm thick PCC (1:4:8) Ty D-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed

M&L for mild steel TMT bars of 10 mm dia and over cut to length bent to shape required including cranking, bending etc. and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per item No 22 here-in-before but 6-8mm dia as in stirrups.

M&L for providing reinforced cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels complete all as specified and directed

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed

M&L for formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed

M&L for RCC (1:2:4) Ty B-1 using 20mm graded stone aggregate as chajjas complete all as specified and directed

M & L for Machine cut kota stone slab flooring 18-20mm thick over & including15mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding and polishing, complete all as specified and as directed.

M & L for glazed ceramic tiles in vertical surface of size 300x450mm/300mmx600mm and 7-8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl 10mm thick rendering in CM 1:4 after dismantling floor, hearth or wall tiling with cement mortar bedding (but not backing), complete all as specified and as directed.

M & L for Coloured Chequered cement concrete tiles 30cm x 30cm x 20-22mm thick, set, jointed and pointed in neat cement slurry over & including15mm thick screed bed in CM 1:6 complete all as specified & directed

M&L Rendering 12 mm thick in CM1:6 on fair face of brick work/ concrete surfaces and finished even and fair complete all as specified and directed

M&L Rendering 15 mm thick in CM 1:4 on fair face of brick work/ concrete surfaces with water proofing compound finished even and fair complete all as specified & directed. Note :- WPC shall be measured and paid separately under relevant item of this Sch /BOQ as Supply only.

Supply only liquid water proofing compound complete all as specified and directed.

M & L for Washed stone grit plaster on exterior walls in two layers (colour and design as approved by GE), under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern (groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove) complete including scrubbing and washing, the top layer with brushes and water to expose the stone chippings including taking down of existing cement or cement lime plaster of any thickness and any description on brick or stone walls including raking out joints, hacking for key and scrubbing down with water, complete all as specified and as directed.

M&L Cement concrete 1:2:4 type B0(using 12.5mm graded crushed stone agg) as in coping, complete all as specified and directed

M&L for cutting holes of superficial area exc 140 sq cm but not exc 400Sq cm into or through brick walls built in cement mortar and making good in CM 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and directed

M & L for preparation of new plaster external wall and ceiling surfaces of and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over and 2mm thick wall care putty complete all as specified and as directed.

S&F for prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

S & F E-board ceiling of size 600x600x4mm thick white pre-laminated sett embossed reinforced designer ceiling board tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 2mm dia to be fixed by approved rawl plug, level and adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture instruction including taking down the existing false ceiling of any type with frame work complete all as specified and directed.

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed

S&F 1.00mm thick mild steel, plain, black sheet hearths; covering to door shutters; covering to door chowkhat (frames); chullah hoods; water tanks; water troughs; ducts; etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and directed

S&F of steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed

M&L for 2 coat of synthetic enamel paint over a coat of red oxide paint over prepared surface of new steel surface complete all as specified and directed

S&F 0.80m deep Cup board divided in cabinets (area of each cabinet box exc 1.50sqm but not exc 3.50 Sqm) fixed to wall with dash fasteners at suitable intervals, made with powder coated aluminium alloy standard hollow rectangular section frame of section 63.50mm x 38.10mm x 3.18mm weighing not less than 1.79Kg/RM on front , inter connections and backside of Cup board as per approved sample and as per IS specifications, with 2 sliding shutters frames in each cabinet weighting not less than 0.55 kg/RM on suitable sliding rail, including provision of 5.5mm thick plain glass of superior quality in cupboard shutters with powder coated handles, 2 track sliding rail, tower bolt, cleats to fix WPC board, rollers hinges, and all standard powder coated fittings complete all as specified and as directed. Note: The work will be carried out with all power coated sections similar to existing cupboard in store at site and as per direction of Engineer in charge.

Dismantling of PVC water tanks exc 500 litres and n.exc 1000 litres capacity of any condition or type complete all as specified and directed.

Dismantling of Cast Iron pipe 100 mm bore complete all as specified and directed.

Dismantling of Cast Iron pipe 75 mm bore complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) laid bedded and pointed in any mortar and removal of old tiles from premises complete all as specified and directed.

M&L for cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 10cm including making good of disturbed surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate complete all as specified and directed.

Dismantling of Brick tiles or terracing tiles, single layer on roofs, kerbs, aprons, etc. (each layer) and removal of rubbish out of defence land complete all as specified and directed. (Note : All roots of plant on either on wall or roof to be removed and making good the disturbed surfaces. The rate quoted by the contractor shall deemed included in the unit quoted rate.)

Demolition of Mud Phuska in roofs, any thickness including plastering and leeping of any thickness upto 30cm deep and removal outside MoD land complete all as specified and directed.

Taking up or down 15 mm bore GI tubing and connections including cleaning for re-fixing complete all as specified and directed.

All as per item No. 53 here-in-before but 20 mm bore

Dismantling structural steel work including doors, gates, railings, purlins etc, but excluding framed truss etc. complete all as specified and directed

Fabrication and fixing of modular wardrobe/ cupboard made out of 18 /20 mm thick WPC boards with 2 mm thick fabric colour laminated sheet of approved quality and texture on all exposed sides with edge band including providing cabinet for keeping baskets/ drawers etc. completed all is specified and as directed.( Design and pattern as approved by GE) Make:- Rajshree or equivalent.

S & F in repairs stainless steel curtain Rod 25 mm dia with holders fixed to wall with finials and bracket etc complete all as specified and as directed.

S & F Continuous (piano) hinges, stainless steel, width of flap 30mm complete all as specified and as directed.

S & F150mm long Brass handles, cast type, polished bright complete all as specified and as directed.

S&F brass 4 lever locks, drawer, grade I, size 75mm complete all as specified and directed.

S&F 125mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

M&L Rendering 5mm thick in CM 1:3 as in ceiling finished even and fair complete all as specified and directed.

M & L for Non-Skid coloured ceramic tiles 7-8mm thick (square/rectangular) of size 300mmx300mm or 400mmx400mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M & L for glazed Vitrified coloured tiles 8-10mm thick (square/rectangular) polished, area of each tile exc 0.42 sqm but n exc 1.00 sqm each in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

All as per Srl item No 66 here-in-before but as in skirting over 10mm thick rendering in CM (1:4) complete

M & L for glazed ceramic tiles in vertical surface of size 300mmx450mm x 7-8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl 10mm thick screed bed in CM 1:4 after dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and as directed.

S&F 15mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete all as specified and directed.

All as per item No 69 here-in-before but 20 mm bore.

S&F white colour Rotational moulded polyethylene water storage tank 1000 litres capacity, white triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittings complete all as specified and as directed.

S & F in repairs Vitreous china single Piece floor mounted WC With PP Soft Close Seat Cover, Hinges, with cistern & Dual Flush Cistern Fitting, Fixing Accessories and Accessories Set, Size: 360x730x740 mm, S Trap- 300 mm including connection to drain pipe with all fitting and fixture complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. SLS-WHT-6851S300PP or equivalent in Marc / Kohler )

S & F in repairs ready made floor/wall mounted Vanity box made of HDHMR board, both side laminated consisting of the following combination :- (a) Wash Hand Basin 810mm x 500mm with CP grating and CP bottle trap. (b) Base Cabinet 780mm x 485mm x 460mm. (c) Side Cabinet 300mm x 250mm x 1800mm. (d) Mirror cabinet size 780mm x 160mm x 800mm. Make : Hindware - Cat Part No. 70089 or 70084. Make : Kohler : Cat Part No. K-31602IN-E63

S&F in repair 15 mm dia brass chromium plated central hole wash basin mixture, fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut capstan head screwed for 15mm dia pipe fixed in repair. (Make Jaquar Florentine FLR-CHR 5273UPR or equivalent in MARC/Kohler)

S&F in repairs of CP towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 190 gms) fixed on walls, complete all as specified. (Make: Jaquar/ Marc/ Kohler)

S&F Hat and coat hooks, set of six, solid body of brass, 175mm to 250 mm complete all as specified and directed.

S&F in repair 15 mm dia stop cock/angle cock cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle, flinch screwed both ends for iron or for union. (make: Jaquar cat no CON-CHR-053 KN or equivalent in MARC/Kohler )

S&F in repair, wall mixer with provision of over head shower chromium plated for mixing hot and cold water screwed for iron pipe suitable for 15mm bore pipes complete all as specified and directed. (Make Jaquar Florentine FLR-CHR-5273 UPR or equivalent in MARC/Kohler)

S&F in repair bib taps brass chromium plated 15 mm bore size screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed (make: Jaquar cat no continental CON-CHR-047 KN or equivalent in MARC/Kohler )

S&F in repair Brass chromium plated shower rose 125mm size all as specified and directed (make: Jaquar/MARC/Kohler)

S&F in repair Stainless steel grating 100mm dia with centre hole of best quality as approved by GE including fixing in CM 1:4 to floor/nahani traps etc complete all as specified and directed.

S&F in repair Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron complete all as specified and directed.

S&F 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms) complete all as specified and directed.

S & F in repairs Designer type high quality fancy type looking mirror of size as approved by Engr-in-Charge 8-10mm thick, fixed to wall with stainless steel studs, screws, brackets and washers etc complete all as specified and as directed.

S&F in repair PVC connection 15 mm bore and 45cm long with washers complete all as specified and directed.

S&F Hubless CI pipes of 100 mm bore ( single socketed in any length with rubber ring joints and clamps including all fittings/fixtures fixed on wall or in trenches or in floor complete all as specified and directed.

All as per item No. 86 here-in-before but 75mm bore.

S&F Hubless CI 100mm bore (single T) or unequal provided with access door complete all as specified and directed.

S&F 100 mm bore CI hubless bends/shoes any radius complete all as specified and directed

All as per item No. 89 here-in-before but 75 mm bore.

S&F in repair UPVC (SWR) 110 mm Nahani trap with grating including jointing to waste pipe in cement concrete complete all as specified and directed.

S&F in repair UPVC (SWR) floor trap, 75mm dia plain including jointing with solvent cement with grating including jointing to waste pipe in cement concrete complete all as specified and directed.

S&F in repair 100 mm bore pipe, stack clamps out of 50mmx 5 mm flat iron and 16 mm dia round iron stamp including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

S&F Framed bracket of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L Cement concrete 1:2:4 type B0 (using 12.5mm graded crushed stone agg) as in roof levelling complete all as specified and directed.

Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 150mm dia pipes complete all as specified and directed.

M&L for complete removal of existing membrane, cleaning of concrete or plastered surfaces of roof and applying priming coat using with bituminous primer @ 0.30kg per Sqm followed evenly by a tack coat @ 1.20 kg per Sqm using 85/25 grade industrial hot blown bitumen, over it laid with 3mm thick APP modified polymeric water proofing membrane minimum weight 3.6 Kg per Sqm reinforced with non-woven polyester fabric (weight not less than 160 Gm per Sqm) unrolled & bonded to substrate with side and end laps 75mm & 100mm as per manufacturer’s instruction and finally finished the top of polymeric water proofing membrane with a coat of bituminous aluminium paint @ 0.20 kg per Sqm as per manufacturer’s instructions over, complete all as specified & directed. Notes- 1. The Work Shall be executed through authorized applicator of manufacturer. 2. Authorized applicator shall be approved by GE before starting of work. 3. All material shall be procured directly. 4. Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of ten years in favour of the GE. A sum equivalent to 2.5% (Two point Five Percent) of the cost of item shall be retained by the Govt from the contractor’s dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer.

M&L Cement concrete type B1-1:2:4 (using 20 mm graded crushed stone agg) in roof kerbs or mud stop rounded or chamfered on edge etc complete all as specified and directed

M & L for preparation of new plastered surfaces of internal wall/ceiling and applying 2 coats of Internal acrylic paint of Dr. Fixit Sureseal or equivalent of Asian Paints or Berger over and including 2mm thick wall care putty and coat of primer complete all as specified and as directed.

M & L for preparation of new plastered surfaces of internal wall and applying 1 coat of texture paint with one coat Internal acrylic paint of Dr. Fixit Sureseal or equivalent of Asian Paints or Berger over & including 2mm wall care putty and coat of primer complete all as specified and as directed.

S&F glass corner shelf fancy type made sheet glass of size fixed with chromium plated brackets complete all as specified and directed. Make : Jaquar ACN-CHR-1173 or equivalent in MARC/Kohler

S&F in repair toilet paper holder of brass, chromium plated fixed to walls with chromium plated(CP) brass screws complete all as specified & directed Make : Jaquar / MARC/Kohler

Taking down old existing water proofing treatment from the top of RCC / arch slab, including taking down existing PCC padding or plaster and hacking the top of RCC slab, cleaning with water and disposal of rubbish off the premises complete all as specified and directed

M&L for 20mm thick cement plaster in CM 1:4 mixed with WPC as per manufacturer's instruction cement finished even and fair without using extra cement on roof surface and wall complete all as specified and directed (Note :- WPC will be measured and paid separately as supply only)

S & F plain gypsum board panel 12 mm thick on false ceiling ( including any design/ cob design as required & pattern as approved by GE) with and including necessary GI frame work for seamless ceiling used with ' T ' , channel or any section including screws , cleats ,fasteners, clips and all required accessories , hangers etc. of galvanized steel all as per manufacturer design conforming to IS-2095 and 2542(1981) the weight of the board shall be not less than 7 kg per sqm and including dismantling of walls and ceiling existing old board (fibre pulp. Insulation etc)or insulation boards/slabs/blanks any thickness including cover fillets etc including two coat of OBD over a coat of putty including dismantling of walls and ceiling existing old board (fibre pulp. Insulation etc.)or insulation boards/slabs/blanks any thickness including cover fillets etc. complete all as specified and directed.

S&F mortice night latch of size 75 mm, 4 levers of mild steel etc. complete all as specified and as directed.

S & F for Magnetic catches with steel body ‘H’ type, fixed to shutter, complete all as specified.

S&F for Its class soft wood moulding of cross sectional area exc 13 sqcm but not exc 25 sqcm fixed with screw as in cornices, picture rails and the like complete all as specified and directed

S & F for Factory made UPVC (white/Off White colour casement (Openable) Door made of extruded profile members with wall thickness of 2.3mm (1-0.2mm). Door profile members with hollow section with multi chamber. Frame (60mm x 60mm), sash bars (60mm x 110mm). T-profile (One vertical length in between two shutters 60mmx 74mm). Glazing head (35mmx 20mm) will be mitered cut and fusion welded at all corners, including making of holes for fixing hardware and drainage of water etc, making arrangement for fixing of hardware EPDM gasket 1.2 to 0.02mm thick galvanised steel frame (28mmx21.50mm), sash bars (31mmx27mm). T-profile (27x17mm) to be inserted in required profile frame and will be fixed to wall 8mm x 100mm long fasteners. Hardware: casement door handle made of zinc alloy (white powder coated), Corner striker, Secondary Strikers, Cylinder, Door transmission gear made of mild steel with multi point locking system with striker, Hinges of zinc alloy (white powder coated) and S.S wire mesh 0.36mm nominal dia of wire and average width of aperture 1.40mm, complete all as specified and as directed. (Note: The unit rate quoted by contractor includes cost of glass, hydraulic door closure, lock and includes all other connected accessories. Net opening will be measured for payment purpose.)

Demolition of cement concrete (reinforced) in any position and paving not exc. 15 cm thick (below or above ground level) complete all as specified and as directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) of internal dia 300mm to 600mm, set in cement mortar and remove from site as directed by Engr in charge.

Excavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation exc on for walls, shafts, manholes not exc 10 Sqm on plan or for laying pipes/cables etc and getting out in soft/ loose soil complete all as specified and directed

M & L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation, filling and mass concrete all as specified and directed.

M & L for brick work in CM 1:4 using Sub class "B" bricks straight or curved on plan exc. 6mmean radius complete all as specified and as directed.

All as per item No 114 here-in-before but except bricks

S&F for 600mm dia reinforced concrete pipes, class NP2, laid and jointed with collars laid in trenches and tested complete all as specified and directed

M&L for PCC (1:3:6) Ty C-2 using 40mm graded stone aggregate as in bed to drain pipes of 600mm bore including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified and directed

Returning filling in incl spreading levelling watering and well ramming in layers not exceeding 25cm in soft or loose soil complete all as specified and as directed.

Removing excavated materials to a distance exc 250m but n exc 500m and depositing where directed at a level not exc 1.5m above the starting point in soils complete all as specified and as directed.

M & L for 15mm thick rendering in cement mortar 1:4 on other than fair face of brick walls/ concrete surfaces and finished even and fair in any position incl scaffolding etc, complete all as specified and as directed.

M & L for coloured rubber moulded coloured chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment over 15mm thick screed bed in CM 1:6 complete after dismantling of existing chequered tiles of any type all as specified and as directed.

S & F for Precast RCC manhole covers 75 mm thick medium duty conforming to IS-12592, including demolition of existing MH cover of any type complete all as specified and as directed.

M&L Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

Taking down/ out carefully copper/aluminium point wiring for light/fan/bell/ sockets 5/15 Amps complete without accessories as switches, Sockets, holders, ceiling roses, light fitting regulators etc (to be measured and paid separately under relevent item of this Sch as S&F in repair and credit for these item given in credit schedule here-in-after) and making good the disturbed surface all as directed.

M&L of point wiring complete with 1.5 Sq mm (nominal area) FRLS PVC insulated sheathed and multistranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and fittings such as tees, bends, elbow, and FRLS PVC insulated unsheathed 1.5 Sqmm copper conductor mulistranded earth wire, connecting to common earth dolly including Metal Flush Box, Cover plate with frame, cutting chases and making good disturbed surface in CM 1:3 to match with existing surface for one light point exhaust fan point controlled by one 1-way switch complete all as directed. (a) one light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push.

(b) one socket outlet point 5 amps on the same board.

(c) one socket outlet point 5 amps on the independent board.

(d) All as per Srl Item No 125 here-in-before but with 4 sq mm FRLS copper wire with 4 Sqmm FRLS copper earth wire for independent point.

S&F in replacement Modular switch 6 Amp, 1 way, 1 module size complete all as directed.,Make-Indoasian shynora,Anchor Roma,Legrand Arteor or equivalent.

S&F in replacement Modular socket 6 Amp, 2/3 pin, universal type, 2 module size complete all as directed.,Make-Indoasian shynora,Anchor Roma,Legrand Arteor or equivalent.

S&F in replacement Modular switch 16 Amp, 1 way, 1 module size complete all as directed.,Make-Indoasian shynora,Anchor Roma,Legrand Arteor or equivalent.

S&F in replacement Modular socket 16 Amp multipurpose shuttered type, 2 module size with indicator lamp complete all as directed.,Make-Indoasian shynora,Anchor Roma,Legrand Arteor or equivalent.

S&F in replacement Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as directed.

S&F in replacement Modular Step Fan regulator, 120 watts single / double module, fixed in repairs, complete all as specifed and as directed.

S& F in replacement LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed

S & F in replacement surface and wall mounted LED tube light fitting with Aluminium housing & interated electronic driver with tube rod of 20 Watt. slim elegant design.and including connected with 3 core 23/0.0076 insulated copper wire from celing rose to fittting connector all as specified and directed.

Taking down ceiling fan any size sealing cable end, dismentling blades and deposited MES store yard. complete all as specified and as directed.

S & F ceiling fan(BLDC) 1200 mm sweep, 5 star rating regulator operated, service value not less than 6.0, 240 volts, 240 Volts. 50 Hz complete all as specified and directed .

S & F MCB DB confirming to IP 43 - IK 09 with double door , SPN 12 way complete with din rail Neutral and earthing bar after taking out the old unserviceable DBs connection and making good the disturbed surfaces complete all as specified and as directed.

S&F in replacement MCB SP, B Curve type, 10 KA, 10 to 32 Amp, with over load and short circuit protection complete all as directed.

S&F in replacement MCB SPN B Curve type, 10 KA,63 Amp, with over load and short circuit protection complete all as directed.

M&L earthing with galvanised steel plate electrode 600 x 600 x 6 mm thick, buried directly in ground( earth pit not less than 2.25m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level , connected to and including galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, washers of galvanised steel earth strip protected by and including 20 mm bore “light grade” and connected to main test point as directed and including concrete pit in PCC(1:3:6) type C1 precast RCC M-25 (design mix) precast cover slab (54 x 54 x 5 cm) duly reinforced with and including 8 mm dia TMT steel bars @ 150 mm C/C both way, one lifting handle made of 8 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI medium grade pipe for watering, charcoal and salt in alternate layers, including necessary excavation and earth work any type of soil complete all as specified and shown in electrical plate No. 5 of SSR Part –I including testing on completion complete all as specified and directed.

S & F in replacement energy efficicent LED fittings 45W LED 6K suitable for builing security light pressure die cast aluminium roadway luminaire with high power LEDs and HF electronic driver complete all as directed.

S&F in replacement of street light fitting bracket, 1.0 mtr long bent to shape made out of galvanized iron pipe of 25 mm dia size light grade complete with nut, bolts, washer, clamps etc inclusive of one primer coat, one under coat and one finishing coat of silver paint complete all as directed.

S&F of Flexible LED tubelar light cool/warm white and making all electric connection complete all as directed. Make - Eveready or equivalent.

S&F of adopter AC to DC sutable for tubelar LED light complete all as directed.

S & F in replacement LED energy efficient integrated battens fittings, Aluminium extruded heat sink with shatter proof opal shell of Aluminium housing, 10 Watts, cool/warm white as per site requirement, complete all as specified and as directed.

M&L Sub main wiring with 2 run of 6.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, PVC concealed conduit 25 mm dia with all fittings and including 6.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire including cutting chases and making good in CM 1:3 and making good disturbed surface to match with the exisitng surface, connected with thimble from main DB to sub main DB complete all as directed.

M&L Sub main wiring with 2 run of 10.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, PVC concealed conduit 25 mm dia with all fittings and including 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire including cutting chases and making good in CM 1:3 and making good disturbed surface to match with the exisitng surface, connected with thimble from main DB to sub main DB complete all as directed.

S&F in replacement exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm and depositing the old U/s item to MES store yard complete all as specified and directed

S & F of rigid non metallic PVC conduit 25mm dia inclusive of all tees, bends, elbow, reducers, bell mouth tube ends and fixing accessories such as couplers lock nuts saddles, pipe hook etc. complete including cutting chasis in wall and making good the surface complete all as specified and as directed.

S&F in replacement of MCCB incommer Distribution Board ( Vertical Load line DB) double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, VTPN 04 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB as incommer and MCB as outgoing and making all necessary connections and taking out the old unserviceable DB complete all as directed. Note:- MCCB & MCBs will be measured and paid separately

S&F in replacement MCCB 3 Pole, 160 Amp with breaking capacity 16 KA suitable for 415 volts AC supply, with over load and short circuit protection complete all as specified.

S&F in replacement of Modular AC 25 Amp SP mini MCB, 230 Volts, 50 Hz suitable for module sheet complete all as specified and as directed.

S&F Automatic Hand drier hot air dispenser with infrared sensor metal body with all accessories including all electrical connection complete all as specified and as directed.Make-Euroforce or equivalent.

Taking down water heater (Geyser) 25 ltre capacity, and depositing to MES store yard.complete all as specified and as directed.

S&F electric water heater of capacity 25 litre, vertical storage type, steel inner tank with glass linen 5 star rating, withstand 8 bar pressure complete with all accessories such as heating element, pressure relief check safety valve, thermostat, connection piece, 3 core wire with plug etc all as specified and as directed.

S&F Steel fastner of 4" long and 8mm dia with Nuts & washer complete all as specified and as directed.

S&F of steel wired connection 600mm long and C P brass adopter 15 mm dia with washer for hot and cold water from geyser and to withstand 8 bar pressure of water complete all as specified and as directed.

S&F of LED bulk head fitting 10W with inbuilt driver complete all as specified and directed.

S&F in replacement of LED bed side light, 5/6 Watts, wall mounted type and making all electric connections complete all as specified and directed. Make Eveready,Crompton,Havell or equivalent.

S&F in replacement round shape 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.Make Eveready,Crompton,Havell or equivalent.

S&F in replacement round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.Make Eveready,Crompton,Havell or equivalent.

S&F of light grade Galvanised mild steel pipe 50 mm bore complete with all fittings, laid under roads, drain, paths, fixed to poles/ walls with suitable mild steel clamps , bolts , nuts and washers complete all as specified and directed as for cable proction .

S&F in replacement decorative Fancy wall light made up of high grade engineering plastic material suitable for 9 Watt LED lamp B22 base. Make Eveready,Crompton,Havell or equivalent.

garnet engineers contractors (BID ID -3375999)

THE LOTUS BUILDTECH (BID ID -3372876)

Atish Builders LLP (BID ID -3376279)

M/s Shubh Enterprises (BID ID -3376039)