REPAIR/ MAINT OF JOINERY, ROOF TREATMENT CHAJJA, TANK AND CLEANING OF SEWAGE LINE AT AKASH VIHAR, 12 AFH,274 SU, 756 SU AND MES UNDER GE AF GORAKHPUR

Amount

Demolition of cement concrete (unreinforced) in ground floors and roof and paving not exceeding 15 cm thickness (below or above ground level) .complete all as specified and directed at site.

Ditto here in above but in RCC ( reinforcement cut as required to facilitate demolition) complete all as specified and directed at site.

M&L for PCC (1:4:8) type D-2, (using 40mm graded stone aggregate) as in foundation, mass fillings,sub base etc. complete all as specified & directed.

M&L for Precast RCC 1: 2:4 type B1 (nominal mix ) using 20mm graded stone aggregates as in drain/MH cover slab etc complete all as specifide and directed .

M&L plain cement concrete (1:2:4) type B-2 using 40mm graded stone aggregate in surface channels and drains complete all as specified and directed.

M&L plain cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as in coping complete all as specified and directed.

S&F 10mm & over diaTMT bars cut to legth, bent to shape required including cranking bending spirally for hooping for slab for manhole etc complete all as directed.

S&F 6mm to 8mm diaTMT bars cut to legth, bent to shape required including cranking bending spirally for hooping for slab for manhole etc complete all as directed.

Extra for forming fair finished drain or channel up to 30 cm inner girth in cement concrete using extra cement incl forms, moulds, mitred/stopped ends etc complete all as specified and directed at site.

Demolition of brick work built in cement mortar or cement lime mortar .complete all as specified and directed at site.

M&L Brick work with sub class B bricks straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and directed at site.

All as per Item No- 11 here in above but except bricks..complete all as specified and directed at site.

M&L for brickwork with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed at site.

Taking down cement or cement lime plaster any description on brick or stone walls, etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed

M&L Rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed

M&L for preparation of new plaster surfaces of wall and applying two coats of cement base paint with one coat of white cement primer on new surface complete all as specified as directed. Note - (Steel Grey Shade and tint shall be decided by the GE).

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises .

M&L Non skid joint less colour Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick cement mortar 1:6 bedding .complete all as specified and directed at site.

S&F Glazed ceramic coloured tiles 300x450x7mm thick in skirting dados risers to steps etc set and jointed in neat cement slurry and pointed in coloured cement to match tiles over 10mm thick rcement plaster in cm 1:4 complete all as specified as directed..

S&F in repair Vitreous China wash down water closet pan (pedestal pattern, with EWC including p or s trap ,seat cover , including connection to trap /drain and to flushing pipe anti syphonage pipe etc complete including making good floorcomplete all as specified as directed.

S&F in repair vitreous chaina squating pan orissa pattern size 580X 440mm white with intregal foot rest complete including lime concrete(excl flushing cistern and flush pipe) but connecting to flushing pipe, anti-symphonage pipe etc complete fixed in repair complete all as specified as directed.

Dismantling mild steel work of any description not otherwise provided for any position complete all specified by Engineer-in-Charge.

S&F framed work such as grills, gate etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conf to Fe 290 Gde E 165 complete all as specified and directed.

M&L preparation of new painted steel surfaces of any description, over 10cm width or girth and apply two coat of synthetic enamel paint over a coat of red oxide complete all as specified and as directed .

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repairs 10 Litre capacity PVC low level flushing cistern with ball valve and handle/push button 32mm dia PVC flush pipe including taking down unserviceable cistern complete all as specified and directed.

S&F in repairs 15 mm bore PVC connection 60cm long with brass nuts and washers on both ends all as in repairs specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

S&F for 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches as in floors, all as specified & directed .

S&F for 110mm bore PVC (SWR) bends provided with access door all as specified & directed .

S&F for 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches as in floors, all as specified & directed .

S&F for 75mm bore PVC (SWR) bends provided with access door all as specified & directed .

S&Fin repair PVC (SWR) P or S trap 125/110 mm,setting and jointing with solventcement complete all specified and directed.

M&L in repair 75mm dia PVC (SWR) floor trap, plane with grating including jointing with solvent cement complete all specified and directed.

Excavation in trenches n.exc 1.5M wide and n.exc 1.5M depth and n.exc 10 Sqm on plan and getting out in any type of soil (for manholes and sewage lines, drain etc.) .complete all as specified and directed at site.

Returning filling in including spreading watering and well raming in layer . Exc 25 cm each in loose/soft soil complete all as specified and directed.

Removing excavated material to a distance not exc 50 m and depositing where directed, complete all as specified and directed

Demolition and breaking up 150mm dia drain pipes ( salt glazed ware, AC or reinforced Concrete ) set in cement mortar complete all as specified.

Concrete bed to drain pipes in PCC 1:4:8 type D2 using 40mm grade stone aggregate including packing under and haunching against the sides of pipe after they are laid and tested for the following 150mm bore pipe.

S&F Reinforced conctrete 150mm bore of pipes class NP2, laid and jointed complete with collars all as specified and directed.

Demolition and breaking up 200mm dia drain pipes ( salt glazed ware, AC or reinforced Concrete ) set in cement mortar complete all as specified.

Concrete bed to drain pipes in PCC 1:4:8 type D2 using 40mm grade stone aggregate including packing under and haunching against the sides of pipe after they are laid and tested for the following 200mm bore pipe complete all as specified and directed at site.

S&F Reinforced conctrete 200mm bore of pipes class NP2, laid and jointed complete with collars all as specified and directed.

Cutting into existing manholes for connecting new drains and making good to pipe and rendering cutting out existing bending for and forming branch channel in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for pipe 150mm bore complete all as specified and directed.

De-silting of sewer line 150/200mm dia with mechanical device like super sucker machine, high pressure jetting machine/gantry machine or any other mechanical device & cleaning site all as specified and directed by Engineer-in-Charge.

Material and labour for Cleaning/removal of blockage from bathroom,EWC/IWC (any type), kitchen, WHB and urinals including connected Nahani traps / gully traps/floor traps, grating of trap, waste pipes, pipe in any length upto first manhole etc choked with mud / other accumulated sludge and getting out, washing thoroughly at any location, at any floor by rodding/choke remover/Pressure technique/manually or otherwise to clear blockage upto entire satisfaction of users,including refixing of oval assess door covers with new nuts & washers and refixing manhole covers, including removing of all wastes, solid or liquid sludge and depositing the sludge in a pit (at empty/open area) of suitable size at a distance exceeding 50 metres from the building where directed and covering the same with the soil obtained from excavation of pit after treating the sludge by spreading the bleaching powder as directed to reduce the foul gases including all excavations and earthwork complete all as specified andas directed .(a) Contractor must employ Minimum 3 Nos labourers daily deployed i.e. 1 No in 12 AFH, 01 No in 274 SU and 1 No for 756SU area, complete all as specified and as directed . (b) Contractor or his representative shall report daily at 09.00 AM except on Sunday/ National holidays in the office of Engineer-in-Charge/ Complaint cell to receive complaint slip and necessary directions. Complaints received through telephonic message from JE/ Engineer-in-Charge shall also be attended on the same day and the completion of work shall be reported by 05.00 PM of every working day to JE/ Engineer-in-Charge. (c) In case of non attedence of complaints against BOQ above by the contractor on the same day, a penalty of Rs 200/- per day will be recovered from the contractor complete all as specified and as directed . (d) The cost for all necessary T&P such as green female bamboo strips, iron rods, sewage rodding machine, buckets, rope, ladder, safety mask, bleaching powder etc and all other other materials for execution of the work shall be included in the unit rate complete all as specified and as directed . (e) A complaint register shall be maintained by JE and proper record of complaints received and attended with date and time shall be recorded and shall be signed daily by both the parties. Complaint register shall be kept on record of Engineer-in-Charge after completion of work complete all as specified and as directed .

Cleaning of septic tanks / Manholes including bailing out water, from it and removing sludge and blockages from inlet and outlet of sewer lines including taking out the excavated sludge and carting away the same to a distance far away from residential/office area and cover the same with fresh earth and recommissioning the septic tank including site clearance to a distance of 3 Metre around septic tank complete all as specified and directed for the following capacity :- (a) For Manhole n. exc 1.50m deep complete all as specified and directed at site.

(b) For Manhole exc 1.50m but n.exc 3m deep complete all as specified and directed at site.

(c) For septic tank of 25 to 50 user capacity complete all as specified and directed at site.

Dewatering of septic tank, sump wells including bailing out water, from it and removing sludge and blockages from inlet and outlet of sewer lines including taking out the excavated sludge and carting away the same to a distance far away from residential/office area and cover the same with fresh earth and recommissioning the same including site clearance to a distance of 3 metre around complete all as specified and directed.

Cleaning of soil pipe lines of any type of 100mm dia by roding from man hole to man hole cleaning eyes and flushing with water for the cleaning incl removal of sludge and re-setting of man holes cover complete.

Ditto all as per item No 51 above but for 150mm dia pipe complete all as specified and directed at site.

Ditto all as per item No 51 above but for 200mm dia pipe complete all as specified and directed at site.

S&F in repair CP Grating 125 mm size complete all as specified as directed.

S&F in repair vitreous china urinal half stall type white complete including providing and fixing plugs,etc all fittings including spreader (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F in repair PVC waste pipe 32/40mm dia for wash basin/sink/urinal ISI marked complete all as specified and directed at site.

M&L Rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces with liquid WPC @ 200 ml per 50 kg of cement or as per manufacturer instructions ( WPC will be measured and paid separately), finished even and smooth without using extra cement complete all as specified as directed.

M&L Rendering 5mm thick in CM 1:3 on celing, finished even and smooth without using extra cement complete all as specified as directed.

M& L prepaation of new plastered surface of wall and applying two coat of cement base paint over a coat ofalkali resistant primer primer and 2 mm tick wall care putty complete all as specified and directed

M & L for Preparing new plastered or unplastered surfaces of wall and applying two coats of distemper oil emulsion, white or tinted over & over a coat of alkali priming coat and 2 mm thick wall care putty, complete all specified and directed

M & L for preparation of new plastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed.

Dismantling Brick tiles or terracing tiles, single layer on roofs including thatching any type, demolition of mud phuska etc including cleaning the surface by water/air pressure and removal of debrish beyond MOD land complete all as specified and directed

Roughening cleaning to RCC roof surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and brushing neat cement slurry with 3.Kg of cement per sqm complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B-I 20mm graded stone aggregate for level course complete all as specified and directed.

M&L for rendering 15mm thick cement mortar 1:4 on fair face of brick work or concrete surface with liquid WPC @ 200 ml per 50 kg of cement, (WPC will be measured and paid seperately), complete all as specified and as directed.

Supply only Liquid water proofing compound ISI Marked complete all as specified and directed at site.

M&L for Water proofing treatment on "Non approachable / non accessible roof" surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer all as specified and directed . (i) Applying approved bituminous based primer conforming to IS : 3384-1995 @ 0.3kg/Sqm to be applied on top surface of prepared surface till the surface is properly impregnated. (ii) Laying APP (Atactic polypropylene Polymer Modified preffabricated membrane) waterr proofing membrane of weight not less than 3 kg/sqm with minimum 100mm side overlap along the length from downward to upward completely sealed with torch application/hot blown lamps. (iii) Applying two cots of bituminous based aluminium paint @ 0.3 kg/Sqm complete all as specified and as directed.

M&L for roof treatment in repair after complete removel of existing old treatment and treated with following specifications :- (a) Priming plastered surface of roof by applying oil based bitumen primer @ 0.30 ltr/Sqm on plastered surface till the surface is properly impregnated. (b) Applying APP based polymeric membrane 3mm thick and weight should not less than 3 kg/sqm and sealed the joint with torch application. (c) Applying a coat of hot air blown grade bitumen of grade 85/25 @ 1.2 Kg/ Sqm.

M&L for cutting groove in brick wall 75mm wide and 65mm deep and shaping horiaontal face of groove with cement Mortar 1:3 for fixing of APP membrane and filling the groove with PCC 1:2:4 type B0 using 12.5mm graded stoen aggregate after inserting membrane complete all as specified and directed.

M&L for Cement concrete tiles 20cm x 20cm x 22mm thick, with grey cement and pigment machine pressed; set jointed and pointed in neat cement slurry , and cut and polished with 15 mm Screed 1:4 bed complete all as specified and directed.

Taking down wooden chowkhat without taking of shutter not exc 1.5 Sqm each complete all as specified and directed at site.

Taking down wooden chowkhat without taking of shutter exc 1.5 but not exc 4 Sqm each complete all as specified and directed at site.

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed by Engr-in-Charge.

S&F 2nd class HW plain solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed at site.

S&F factory made pressed steel frames section 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed.

S&F factory made pressed steel frames section 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed.

M & L factory made IInd Class hard wood 30mm thickness Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed at site.

M&L factory made 30mm thick factory made flush door shutters solid core construction with block board core and ply wood face panels commercial type on both faces complete all as specified and as directed.

S&F factory made 30mm thick 2nd class HW glazed skeleton shutters open rebated and prepared to receive glass gazed etc but divided into squares with plain chamfered or rounded mitred and rebated sash bar any numbers edges of framing plain chamfered or rounded fitted with cut and mittered beads for sceuring glass guage etc. size of members as specified in SSR pt-I section 8 clause 8.24(a) fitted to chowkhats.

S&F factory made steel windows with side hung shutters incl box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete

ditto all as per item above but without glazing bars complete all as specified and directed at site.

S&F factory made steel window, ventilators, fixed type, with glazing bars complete all as specified and directed at site.

S&F framed work as in doors or gates of angle or other section with guesset plates complete doors etc to be prepared to hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging, also fastening and fixing complete.

S&F framed work such as grills gratings etc with ends of bars shouldered and /or riveted or forged into spikes, framed guard bars, barred iron doors, ladders framed, baluster walk ways, railings, framework of water tanks & similar wk conforming to Fe410-0 or Fe310-0 .

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

S&F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed at site.

S&F factorymade solid pannel PVC door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with neat moulded plan colour PVC 'C' channel having a PVC sheet strips of 20mm width stuck in side with solvent cement for styles and plain colour PVC sheets for top rails, lock rail and bottom rail on eithor side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheets to be fitted in the MS frame welded/sealed to the stiles, and rails with suitable PVC sheet bedding and jointed together with solvenet cement, supply and fixing in the frame at site complete all as specified and directed at site.

S&F butt hinges medium weight cold rolled mild steel 100mm complete all as specified and directed at site.

S&F in repair butt hinges medium weight cold rolled mild steel 100mm complete all as specified and directed at site.

S&F 125mm aluminium anodised of extruded section barrel tower bolts complete all as specified and directed at site.

S&F in repair 125mm aluminium anodised of extruded section barrel tower boltscomplete all as specified and directed at site.

S&F 150mm long alumiunium handles cast type anodised complete all as specified and directed at site.

S&F in repairs 150mm long alumiunium handles cast type anodised complete all as specified and directed at site.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed 300mm long complete all as specified and directed.

S&F in repairs aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed 300mm long complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue with hard drawn steel spring with 140mm overall length of cover plate.

S&F mild steel 300mm, ordinary rat tail rod pattern spring, including roller and roller plate complete.

M&L in repairs anodised aluminium (sliding/hanging type) windows/ventilator with frame size 60x40x2.00mm thick and shutter with section bearing bottom 25x18x1.50, top 39.4x17.7 X1.50 mm ( suitable for moving over three track fixed over top of frame work , top and side section of size 61.6 x 31.75x1.5mm and bearing bottom track of size 61.6x 31.75x1.5mm or fixing with hinges including necessary aluminium jointing cleats, glazing cleats, rubber packing anodised snape beading, screws etc with 4 mm thick tinted/ plain glass in panels incl all fitting and fixture complete all as specified and directed.

S&F in repairs mild steel 300mm, ordinary rat tail rod pattern spring, including roller and roller plate complete all as specified and directed at site.

S&F in repairs door seal brush to provide safety from snakes/incests complete all as specified and directed.

M&L for preparation of new painted wooden based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S&F in repair stainless steel harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers but of anodised aluminium alloy etc complete al as specified and directed.

M&L in repairs for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc. 0.5 Sqm in each pane complete all specified and as directed.

S&F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed.

S&F in repairs Steel rolling shutters, 1.25 mm thickness of laths, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complet all as specified and directed.

M&L in repairs anodised aluminium doors (sliding/hanging type) with frame size 101.60X44.45X 2.00 mm thick and shutter aluminium anodised and top rail 47.62X 44.45 X 1.50mm and style 47.5 x 44.5 x1.5 mm , lock rail 83.50X 44.45 X 1.50 mm and bottom rail150.00X 44.50 X 2.50 mm incl necessary aluminium fittings like aluminium butt hinges 04 Nos , aluminium handles 150mm 02 Nos,aluminium tower bolts 200mm 01No, mortice lock 4 lever MS, hydraulic door closer of suitable capacity 01 No, aluminium door stoper 01 Nos, jointing cleats,glazing cleats,rubber packing , anodised aluminium shape beading, screws etc with panelling in two parts with 12mm thick prelaminated partical board in lower panel and 5mm thick tinted glass in upper panels incl all fittings& fixture complete all as specified and directed.

M&L in repairs powder coated aluminium (sliding/ hanging type) windows/ventilator with frame size 60x40x2.00mm thick and shutter with section bearing bottom 25x18x1.50, top 39.4x17.7 X1.50 mm ( suitable for moving over three track fixed over top of frame work , top and side section of size 61.6 x 31.75x1.5mm and bearing bottom track of size 61.6x 31.75x1.5mm or fixing with hinges steel wire cloth 0.36mm nominal dia of wire and average width of aperture1.4 mm including necessary aluminium jointing cleats, glazing cleats, rubber packing anodised shape beading, screws etc with 4 mm thick tinted/ plain glass in panels incl anodised aluminium grill with all fittings & fixture complete all as specified and directed .

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for Joist, channel, angle, or tee sections, Fe 410 -W (Gde E- 250) quality A fixed independently, with or without connecting plates, etc complete all as specified and directed.

M&L for hot rolled steel flat Framed work of water tanks mesh welded and similar work conforming Fe 410 -W (Gde E- 250) quality A complete all as specified and directed at site.

S&F 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as spcified and directed.

M&L preparation of new painted steel surfaces of any description, over 10cm width or girth and apply two coat of synthetic enamel paint over a coat of red oxide complete all as specified and as directed .

S&F in repairs rotational moulded polethylene water tank of 1000 ltrs capacity, ISI Marked (cylindrical vertical with closed top with suitable size of M S Tasla with suitable locking system) hoisted and fixed in position SSR Part- I complete all as specified and directed.

S&F in repairs rotational moulded polethylene water tank of 500 ltrs capacity, ISI Marked (cylindrical vertical with closed top with suitable size of M S Tasla with suitable locking system) hoisted and fixed in position Part- I complete all as specified and directed.

S & F in repairs 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed at site.

S&F in repairs 20 mm bore GI tubes, medium grade galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors or concealed including taking up or down steel tubing and connections including cleaning for re-fixing or removal to store complete all as specified and directed.

S&F in repairs PVC ball valve 20mm dia with epoxy coateed aluminium rod and high density ball (minium weight 210 gms) complete as directed .

S&F in repairs Door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters fixed complete all as specified and directed.

M/s Vivek Traders (BID ID -3319520)

M/s Ishwarchand Traders (BID ID -3316827)

M/S SHRI RC YADAV (BID ID -3319890)

H AND Y GROUP (BID ID -3327689)

GANGA TRADERS (BID ID -3320027)

SANDHYA ENTERPRISES (BID ID -3327886)