SPECIAL REPAIR TO FLOORING, JOINERY,ROOF SHEETING AND ELECTRICAL WORKS IN BLDG NO T-219 (STORE), T-61 (LRW OR LINE),T-62 (CLK LINE) UNDER GE (NORTH) MAMUN AT MAMUN MIL STATION

Amount

Taking down chowkhats or frames of any description not exc 1.50 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware , complete all as specified and directed.

Taking down chowkhats or frames of any description exc. 1.50 Sqm and n.exc 4.00 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware complete all as specified and directed.

M&L for pressed steel frames 125mmx60mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface complete all as specified and directed.

M&L for pressed steel frames 105mmx60mm for door, made out of 1.25 mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate and back filling for chowkats in PCC (1:3:6) type C-0 (using 12.5mm graded crushed stone aggregate) tarring ends incl 02 coats of synthetic enamel paint over a coat of red oxide primer on exposed surface complete all as specified and directed.

M&L for 35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12mm veneered particle board with commercial veneering on both faceS ,The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated, fitted to chowkhats incl 02 coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and directed.

M&L for 35mm thick glazed and skeleton shutters (Factory made) of 2nd class hard wood and prepared to receive glass or gauge etc with rounded, chamfered or mitred sash bars edges of framing plain chamfered or rounded fitted with cut and mitred beads and fitted to chowkats for securing glass/gauge, size of stiles rails and other parts as per clause 8.20 (a) of SSR Part-I 2009 (Larger size to be provided) incl 02 coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and directed.

M&L for Box type Steel windows and ventilators comprised of tubular frame and shutters made out of 1.25mm thick M S sheet tube factory made with double side hung wire gauged shutter & glass/glazed shutter (wire cloth and glass panes only shall be measured and paid separately) with steel handle and steel peg stay dovetailed or welded incl 2 Nos. tower bolts 150mm long for each leaf and 10mm square bar grills at spacing as shown on drg, welded to F I frame work, including other fittings; hinges, handles, tarred hold fasts fixed in PCC blocks all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks, orstainless steel wire staples complete all as specified and directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty or fixed with beads/ glazing pins not .exc 0.5sqm in each pane complete all as specified and directed.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

M&L Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding/ridge to wall, fixed with self tapping screws as specified complete all as specified and directed.

M&L for 300mm aluminium sliding door bolt with hasp & staple (bolt type) (ISI MARKED) and fixing clip of sheets cast or extruded section and fixing sliding bolt of extruded section etc complete all as specified and directed.

M&L for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed. complete all as specified and directed.

M&L for Aluminium anodised handle, extruded section of size 150mm etc complete all as specified and directed.

M&L for False ceiling of 9.5mm thick gypsum tiles (600x600mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film (shade either plain white or crack) in a grid size of 605x605mm from manufacturer M/s Saint Gobain or equivalent of Armstong/Everest including taking down existing ceiling board of any type/pattern with GI frame work with grid size of 605 x 605 mm for seamless ceiling comprising of GI perimeter channel 0.5 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI Hangers 2 mm dia (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3 mm sixe 60mm long and expansion hold fasteners 12.5mm ida, 40mm long incl taking down existing grid complete all as specified. complete all as specified and directed. Note :- Invoice from company’s authorized dealer shall be submitted with material by the contractor along with dealership certificate. Certificate of genuineness from the manufacturer shall also be submitted by the contractor before getting the material passed from the department.

Taking down cement plaster on brick or stone walls,etc including racking out joints , hacjking for keys,scrubing down with water etc, and removal of rubbish out off the permises complete all as specified and directed.

M&L for rendering 10mm thick on brick work or concrete surface in CM (1:6) on wall surfaces finished even and smooth without using extra cement including preparation of new plastered surfaces of wall & applying two coats of distemper oil emulsion (OBD) over a coat of primer as per manufacturer instructions (from same manufacturer of OBD) over and including a layer of wall care putty 2mm thick complete all as specified and directed. complete all as specified and directed.

M&L for Rendering 15mm thick in two layers [base layer 10mm IN CM 1:6 & finishing layer 5mm thick in cement mortar (1:4)] using liquid water proofing compound in IInd layer only on brick work or concrete surfaces of wall, surfaces finished even and smooth without using extra cement including applying two coats of cement base paint over a coat of alkali resistent priming primer/paint as per manufacturer instructions complete all as specified & directed.

Demolition of cement concrete (unreinforced) of any description in any position complete all as specified and directed .

M& L industrial tile not less than 10mm thick as in flooring over and including 15mm thick screed base or bedding in cement morter (1:6) laid and joint with grey cement slurry mixed with pigment to match the shade of the tile including 25mm thick PCC 1:2:4 type B1 (20mm graded crushed stone aggregate) as in sub base of flooring complete all as specified and directed.

M& L industrial tile not less than 10mm thick as in riser/dado (vertical surface) over and including 10mm thick screed base or bedding in cement morter (1:3) laid and joint with grey cement slurry mixed with pigment to match the shade of the tile complete all as specified and directed.

M&L for Brick work with Fly Ash Brick (Non-Modular) Class 7.5, straight or curved on plan exceeding 6m mean radius built in CM (1:6) including demolition of old existing brick work complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description in any position not otherwise specifically provided for cement concrete (reinforcement cut as required to faciliate demolition) complete all as specified and directed.

M&L for RCC( 1:1.5:3) type A-1 (using 20mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary formwork complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for 60mm thick factory made rubberised coloured (laminated) interlocking paver block (using vibro compaction method) (topping thickness not less than 5mm) in white cement and non fadable glossy pigment of approved shade of any shape and size conforming to IS-15658-2006 of M-35 grade over and including 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in coping, including nessasary form work etc complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection laid in panels and joints filled with mix of bitumen 85/25 grade and sand (1:2) by weight, finished the surface even and smooth without using extra cement etc complete all as specified and directed.

M & L for sand filling under floors or in foundation including watering and consolidation as required on the site complete all as specified and directed by the Engr-in-Charge.

Dismantling of existing framed trusses of Span exc 10 m (Steel work in tubular trusses) fixed with special shaped washer including refixing of trusses on the base plate anchor with holding down screw including two coats of synethic enamel paint after prepartion etc. complete all as specified and directed.

Dismantling of structural steel work (rolled mild steel work) including framed truss as in tubular purlins, rafter etc including refixing of tubular purlins, rafter on trusses with nessasary cleats including two coats of synethic enamel paint after prepartion on complete structural steel work complete all as specified and directed.

S&F in repair Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

M&L for G.I., round flat washers for 16mm bolts or screws complete all as specified and directed.

M&L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 45.0cm long & 16 mm diameter of neck complete all as specified and directed.

M&L for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410 -W (Gde- E- 250) quality - A complete all as specified and directed.

S&F in repair for 25mm bore anodised aluminium alloy, single curtain rod (wall thickness not less than 1mm) including fancy type PVC brackets of approved design/pattern, funnels etc suitable for single curtain rod complete all as specified and approved by GE.

M&L for Hard core, Broken stone aggregate to gauge n exc 63 mm as in plinth protection / sub bases etc deposited , spreaded and levelled in layers not exceeding 15 cm thick well watered and rammered to true surface complete all as specified and directed.

M&L for Floor door stopper of aluminium alloy body and tongue with Overall length of cover plate 150mm, anodised, with hard drawn steel spring,fixed in floor complete all as specified and directed.

M&L for Rolled sections as in framing FOR COOLER STAND for cladding, glazing and the like fixed with angle cleats and connecting plates, etc conforming to Fe 410 -W (Gde- E- 250) quality - B, including dismantling of old frame work complete all as specified & directed.

M&L for Mild steel 300mm long , ordinary rat tail rod pattern springs for doors including roller and roller plate complete all as specified and directed.

M&L for Aluminium Wardrobe hooks (single) of size 50mm to 60mm long complete all as specified and directed.

Taking down carefully unserviciable/ damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets, Bracket /sketch fitting etc ) and removing material from site and making good to the disturbed surface to match with existing finish complete all as specified and directed.

M&L for Modular Point wiring using FRLS PVC insulated unsheathed /multi stranded copper conductor cable 1.5 sqmm including 1.5 Sqmm FRLS PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box and approved make sunken metal flush gang box and suitable support frame and cover plate (inner/outer) of required modules for mounting modular switches/ sockets etc, one light point controlled by one switch, 5 Amps SP, one way, 240 watts connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for light/fan/bell point complete all as specified and directed. Make of cable : Finolex, Anchor, Polycab (Note : Modular switch/bell push/fan regulator etc shall be measured and paid separately under respective items.)

All as per Srl item No.46 above but for one multipin socket (5 pin) controlled by one switch, single pole, 5 Amp, 240 volts on the same board etc complete all as specified and directed.

All as per Srl item No.46 above but for one multipin socket (5 pin) controlled by one switch, single pole, 5 Amp, 240 volts on independent board etc complete all as specified and directed.

M&L for Modular Point wiring using FRLS PVC insulated unsheathed /multi stranded copper conductor cable 2.5 sqmm including 2.5 Sqmm FRLS PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box and approved make sunken metal flush gang box and suitable support frame and cover plate (inner/outer) of required modules for mounting modular switches/ sockets etc, for one modular 6 pin socket outlet 15 amps multi purpose independent point controlled by 15 Amp switch Single pole , one way , 240 volts l connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for light/fan/bell point complete all as specified and directed. Make of cable : Finolex, Anchor, Polycab (Note : Modular switch/bell push/fan regulator etc shall be measured and paid separately under respective items.)

S&F Modular Socket outlet, 6/16 pin, 2-in-1, multi purpose 2 module 16 Amps, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKSWW065 or equivalent of Legrand/Siemens/Schenider/Anchor Roma.

Supply only Modular Socket outlet, 6/16 pin, 2-in-1, multi purpose 2 module 16 Amps, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKSWW065 or equivalent of Legrand/Siemens/Schenider/Anchor Roma.

S & F modular switch piano type flush button 16 Amp one module, complete all as specified and directed. Make : Legrand Cat Part No 673009/Crabtree Cat Part No ACMSXXW102/Anchor Roma Cat Part No 66104.

Supply only modular switch piano type flush button 16 Amp one module, complete all as specified and directed. Make : Legrand Cat Part No 673009/Crabtree Cat Part No ACMSXXW102/Anchor Roma Cat Part No 66104.

S & F modular switch piano type flush button, single pole, 10 Amp, one module, front operated, complete all as specified and directed. Make : Legrand /Crabtree /Anchor ( Roma) .

Supply only modular switch piano type flush button, single pole, 10 Amp, one module, front operated, complete all as specified and directed. Make : Legrand /Crabtree /Anchor ( Roma) .

S&F Modular Socket outlet, 5 pin, multi purpose, 2-in-1, 2 module 6 Amp, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKCWW163 or equivalent of Legrand/Siemens/Schenider/Anchor Roma

Supply only Modular Socket outlet, 5 pin, multi purpose, 2-in-1, 2 module 6 Amp, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKCWW163 or equivalent of Legrand/Siemens/Schenider/Anchor Roma

M&L for Sub main wiring with FRLS PVC insulated unsheathed 2X6 sqmm multistranded copper conductor cable 1100 V with 1X6 sqmm FRLS PVC insulated green multistranded copper cable for continuous earth drawn through & including concealed PVC conduit of appropriate size not less than 20 mm dia & 1.8mm wall thickness with all accessories including cutting grooves and making good disturbed surface to match existing including taking down existing surface sub main wiring complete all as specified and directed. (Note: Two runs of FRLS PVC cable with one run of earth conductor and conduit shall be measured as one RM.) Make for wiring : Polycab/Anchor/Finolex

S&F Ceiling rose polycarbonate isolated body surface Bakelite, not less than 65 x 50 mm, three terminals, AC 230 volts etc, complete all as specified and directed. Make : Havells Cat Part No Reo/Cona Cat Part No 9246/GM Cat Part No 8224

S&F taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed. Note : Old ceiling fan as obtained from the site shall be deposited in the store yard of GE (N) Mamun as applicable.

Taking down including refixing of ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan Painting of ceiling fans complete, including minor repair such as replacement of locking pin, reel insulators, bolts, nuts on the site including spraying with one coat of synthetic enamel paint including filling cavities with filler, after cleaning all dust etc complete all as specifeid and directed.

S & F, testing and connecting ceiling fan of size 1200mm sweep, 5 star rated, single phase, 230 volts comprises of double ball bearing type with down rod, canopy cover (Both up and down) including writing of MES fan No with black enamelled paint and connected with insulated and overall sheathed flexible copper conductor cable and including 3 core 0.50 Sqmm complete all as specified and directed. Make : Havells/Orient/Bajaj/Crompton Greaves

S&F Fan regulator modular step type suitable for 1200/1400mm sweep ceiling fan hum free, 100W- 2 module including necessary connections complete all as specified and directed. Make : Legrand Cat Part No 673028/Crabtree Cat Part No ACARFHW005/Anchor Roma Cat Part No 66502.

Supply only Fan regulator modular step type suitable for 1200/1400mm sweep ceiling fan hum free, 100W- 2 module including necessary connections complete all as specified and directed. Make : Legrand Cat Part No 673028/Crabtree Cat Part No ACARFHW005/Anchor Roma Cat Part No 66502.

S &F Street light fitting LED type 20 watt complete with 20 watt LED and having (IP-66 protection) made up of pressure die cast housing with toughned glass and individual high power LED with secondary optics and impact resistance of rating IK-07 and fixing on pole/ceiling complete with all accessories and including connecting up with ceiling rose with & including PVC insulated and overall sheathed flexible copper conductor cable and including 3 core 0.50 Sqmm complete all as specified and directed.

S &F as in repair the bulk head light fitting LED type 10 watt complete with 10 watt LED and having IP-63 protection and fixing on wall/ceiling complete with all accessories and including connecting up with ceiling rose with & including PVC insulated and overall sheathed flexible copper conductor cable and including 3 core 0.50 Sqmm complete all as specified and directed.

S &F as in repair decorative wall mounting bed side light fitting LED type of 3 watt with having flexible neck for smooth swing complete with all accesories internally prewired and including connecting up with three core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

S &F as in repair wall mounted 1x9 watt type fancy light fitting suitable for retrofit LED lamp B 22 with decorative diffuser and mounting clips, lamp holder with wall mounting arrangement including 9 watt LED bulb complete with all accesories internally prewired and including connecting up with three core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

S &F as in repair 1x 20 watts , white powder coated CRCA box type LED batten with decorative end cap including polycarbonate LED tube light fitting / energy efficient fixture 230 volts, wall mounted complete with and including all accesories internally prewired and including connecting up with three core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

S & F mirror light 1x7 watt LED type with all accessories including inbuilt lamp connecting electrically to ceiling rose including cord flexible 3core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm complete all as specified and directed. Notes for Srl Item Nos 65 to 70 :- 1. Driver shall be potted antivibration type. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be povided. 3. CRI (Colou Rendring Index) of fixture shall be > 70. 4. CCT (Colout Correlated Temprature of fixture shall be 5700K ± 300 K. 5. System Lumen Efficacy shall be > 100Lm/W 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 5 years gurantee shall be provided by contractor suppoted by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the Contractor shall replace / repair the defective fitting within 07 Days after handing over to Contractor for replacement / repair 11. CA No shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintaince required, if any can be carried out from Top cover.

S&F for MCB single pole (SP) 240 volts, 6 to 32 Amps, 10KA (C-series) , complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole neutral (SPN) 240 volts, 40 to 63 Amps, 10KA (C-series) complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB triple pole neutral (TPN) 415 volts, 50 Hz 32 Amps, 10KA (C-series) complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F Double door MCB DB TPN, 240 Volts, 04 Way made out of 18 SWG CRCA powder coated sheets, (IP43 protection) (phosphates powder coated with copper bus bar), earth stud, din rail, polyamid terminal blocks for incoming and outgoing circuits, inbuilt loose wire box, ground terminal blocks, duly prewired with thimble flame retardent copper conductors and polylayer for protection including 200 Amp rated bus bar, 4 way, double door openable including taking out old unsv DB any size/type, complete all as specified and directed. Make: Legrand or equivalent in performance in other makes L&T/Hager/SCHNEIDER

Supply , laying, testing and commissioning for 1100 volt grade XLPE insulated heavy duty cable, 16 sqmm 4 core, strip armoured with aluminium stranded conductor overall PVC sheathed laid in trenches including taking down existing cable & bricks complete all as specified and directed. Note : Excavation & Earthwork shall be measured and paid separately.

M & L for well burnt bricks , laid flat ( old size) sub class B designation 75 for cable protection complete all as specifed and directed.

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation etc (for cable, pole stay manhole etc), in any type of soil and getting out, complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25cm thick, etc complete all as specified and directed.

Removing excavation material n exc. 50m & deposited where directed at a level n exc. 1.5m above the starting point etc complete all as specified and directed.

M&L for Sand filling in trenches dry and clean sand unwashed including punning around cable for protection of under ground cable duly compected and rammed with a layer of sand of 8 cm depth for the purpose of cushioning.and after laying cable the same shall be covered with sand to a depth of 15 cm (with overall 23cm of depth of sand cushioning punned down to 18cm) complete all as specified & directed. Note : Punned thickness shall be measured and paid accordingly]

S&F for GI tubing 40 mm bore light grade laid in trenches/floors/ fixed to wall/poles for protection of cable with necessary fittings and FI clamps duly painted complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, HDPE pipe 15mm bore as protection pipe, GI watering pipe 20mm bore light grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC (1:2:4) type B-0 (Nominal mix) cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as directed. Notes: 1. Earth lead & protection pipes length upto & including 7.50 metre is deemed included in unit rate quoted by the contractor. 2. Earth filling shall be done by vegitable soil. 3. Soil shall be free from stone, boulders, aggregate, gravels .

dadwal engineers

naresh kumar sharma

GANDOTRA CONSTRUCTION CO

RD Engineers

M/S J N TRADERS

M/S INDIAN ELECTRICAL

A V BUILDERS

M/s Rajeev Vashist