ADDITION/ALTERATION CUM SPECIAL REPAIR TO BLDG NO 7/3 AT CARIAPPA ROAD, ADDITION/ALTERATION IN BLDG NO P-33A FAMILY OPD FOR CREATION OF ATTACHED TOILET FACILITIES WITH MO ROOM AND EXTN BLDG AT MH AND PROVISION OF 72 X EXHAUST FAN WITH ALL CONNECTED I

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed

M&L for point wiring with FRLS/FRLSH PVC insulated unsheathed stranded copper conductor cable 1.5 Sqmm (nominal area) 1100 volts grade, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly drawn in and including non metallic PVC rigid, medium grade concealed conduit with all fixing accessories of 20mm dia, and including modular sunken box, cover plate / frame for any module as required at site with all accessories and making good to disturbed conceal surfaces complete all as specified and directed for the following :- Note:(a) Colour code of wire shall be strictly followed , Red for Phase , Black for neutral and green for earth wire. (b) The unit rate quoted is deemed to be inclusive of cost of cutting chases in wall for providing concealed conduit and making good to match with existing finish/surface. (c) Only 04 point shall be allowed is one circuit.

M&L for 80mm thick M-40 grade factory made rubber moulded vaibratory cement concrete coloured interlocking paver block (yellow, red or both in combination) any shape and size conforming to IS 15658-2006 with grey cement and no pigment complete all as specified and directed.

M&L for Vitrified Ceramic coloured tiles double charged stain free 10 mm thick (square/ rectangular) polished, area of each tiles n.exc 0.36sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for Vitrified Ceramic coloured tiles double charged stain free 10 mm thick (square/ rectangular) polished, area of each tiles n.exc 0.36sqm , in skirting, walls(elevation tiles) etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) area exc1.5 but n. exc 4 Sqm each.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) area n exc 1.5 Sqm each.

S & F Solid PVC moulded door frame of size 50mm x 47 mm made out of 5 mm thick single side prelam PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made Solid PVC moulded door shutters 28 to 30 mm thick (stiles) with particle board core, with 2, raised panel design with 2 mm thick moulded Prelam on front face and 2 mm thick prelam PVC sheet on back side completed all aspecifed and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 X 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Schedule of Credit (MINUS) Rs. 29,670.00 B/F from Serial Page No. ____ [Note : Details of items for schedule of credit is given on Srl Page No. ___] This amount shall be automatically deducted to arrive at tendered sum

S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S&F 30mm thick FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company , Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per S:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube.Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in -charge, manufacturer's specification & drawings.

Providing and fixing factory made Upvc white colour Sliding Window Three Track made of extruded profiles with wall thickness of 2.3mm (+-0.2mm) Window profile with hollow section with multi chamber, Frame (108mm* 45mm), sliding Sash (39mm 58mm). Sliding mesh sash (39mm 58mm) Sliding Interlock (One vertical length in each shutters) (45mm 35mm). Glazing bead (20mm 18mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+-0.2mm thick. galvanized steel frame (32mm 13mm), 2 Nos, Sliding Sash (29mm*19mm), Profile to be inserted in required profile, frame will be fixed to the wall with 8mm*100mm long fasteners. Hardware: [Touch Lock of zinc alloyed (White powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. Glass: 5/6mm Toughened glass. Note : The unit rate quoted by contractor excluded cost of glass & includes all other connected accessories net opening will be measured for payment purpose.)

S&F window guard bars, plain let in and fixed independently in any frames L or T section support for shelves etc., or Expanded wire mesh fixed at any height and similar articles conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed

Supply and fix/fabrication in repair kitchen cabinet & wardrobe/ cupboard made out of 16 to 18 mm thick PVC board plain sheet including fixing of cabinet for keeping baskets/ cutlery basket with handles complete.Make : Rajshree or equivalent all as specified and approved by Accepting Officer.

M & L for Non Skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Supply only stainless steel acessories suitable for kitchen cabinets as under:-

Stainless steel basket (plain) of size 50cmx37cmx10cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised

over rollers of approved make Make: Life style Cat part No WA/POB/15204 or equivalent approved

Stainless steel thali basket (11-13 division) of size 50cmx37cmx20cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved Make: Life style Cat part No WA/TB/15208 or equivalent approved

Stainless steel Plate basket (11-13 division) of size 50cmx37cmx16cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved Make: Life style Cat part No WA/PTH/15206 or equivalent approved

Stainless steel Cutlary basket of size 50cmx37cmx10cm made of 4mm th S.S.wire and bottom of S S perforated sheet approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approvedMake: Life style Cat part No WA/CUT/15204 or equivalent approved

Stainless steel basket (plain) of size 50cmx37cmx16cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved Make: Life style Cat part No WA/POB/15206 or equivalent approved

Description same all as per Item No 11 here in above but section of frame 65X125mm complete all as specified and directed.

S&F continues (piano) hinges, mild steel, bright finish width of flap (when open) 30mm complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

M & L for Glazed Ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including screed bed 10mm thick in cement mortar 1:4 finished rough to receive wall tiles etc complete all as spd and directed.

S&F solid PVC wall lining consisting of 5mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications complete all as specified and directed.

S&F in repair 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing with solvent on to wall to make PVC frame as per specifications complete all as specified and directed.

M&L for preparation of old/new painted surface of steel and iron of any discription, not otherwise described, over 10cm in width or girth and applying one coat of synthetic enamel paint, white or tinted complete all as specified and directed.

M&L for preparation of old/new painted surface of wood and wood based materials of any discription, not otherwise described, over 10cm in width or girth and applying one coat of synthetic enamel paint, white or tinted complete all as specified and directed.

S&F 200 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed

S&F magnetic catches with steel body ‘H’ type, fixed to shutter complete all as specified and directed.

S&F 75 mm dia brass handle cast type polished bright finish complete all as specified and directed.

All as per ser item No 29 here in above but 150 mm long complete all as specified and directed.

All as per ser item No 29 here in above but 100 mm long complete all as specified and directed.

S&F MS Butt hinges medium wt cold rolled of size 125 mm complete all as specified and directed.

S&F SS sliding door bolts plate type stove enamelled black with bright bolt not less than 12mm dia with & including a min of 6 bolts & nuts four on bolt plate & two on staple plate & fixed 300 mm long complete all as specified and directed.

S&F SS bow handle,cast type,100mm long complete fixed with steel screws complete all as specified and di

rected.

S&F SS bow handle,cast type,anodised 150mm long complete fixed with steel screws complete all as specified and directed.

S&F in repair rotational moulded,multilayer HDPE water storage tank of 500 (triple layer white colour) ltrs capacity(Cylindrical vertical with closed top) ISI marked fixed in position on existing places complete all as specified including 02 Nos 20mm dia full threaded GI tank niple, 20 mm dia PTMT float valve epoxy coated Aluminium rod with high density plastic float ball( of minium weight 210 gms ) and refixing of inlet, outlet & overflow pipe etc, complete all as specified and as directed.

Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as spd and directed.

S&F 4 mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads in square area exc.n 0.5 Sqm in each pane complete all as specified and directed.

Demolition of brick work built in cement mortar and removing rubbish complete all as specified and directed.

M&L Brick work with fly Ash old size bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

All as per Ser Item No 40 here in above but 20 mm dia bore complete all as specified and directed.

All as per Ser Item No 40 here in above but 25 mm dia bore complete all as specified and directed.

Refixing old steel tubing and connection in new or old position in wall/ceiling/floor etc bore of pipe 15mm dia with new fittings complete all as specified and directed.

S&F for 15mm bore steel tubes “medium grade” galvanised with all fitting and fixed complete in walls ceiling or laid in floors complete all as specified and directed.

Stainless steel bottol full out of size 50cmx40cmx16cm in two tier made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make Make: Life style Cat part No FF/BPO/62018 or equivalent approved

All as per Ser Item No 43 here in above but 20 mm dia bore complete all as specified and directed.

All as per Ser Item No 43 here in above but 25 mm dia bore complete all as specified and directed.

Cutting chases pinning in making good to facing where required for concealed water tubing and making good cutting not exc 10cm girth in brick walls complete all as specified and directed.

S&F in repair for wall mixer with connecting legs and wall flanges with provision for overhead shower with 115 mm 15mm dia chromium plated brass and securing to walls complete all as specified and directed.

S&F in repair 15mm dia Brass CP central hole mixter for mixing hot & cold fancy type screwed down ,high pressure long screwed shanks and fly nuts , screwed for iron pipe complete all as spd and directed.

S&F in repair 15mm dia Brass CP sink mixter for mixing hot & cold fancy type screwed down ,high pressure long screwed shanks and fly nuts , screwed for iron pipe complete all as spd and directed.

S&F in repair brass chromium plated towel rail 20mm dia D type, 60cm long between flanges fixed with screw to wall complete

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F in repairs shower CP fancy type 125 mm including shower arms complete all as specified and directed.

S&F in repair PVC mirror cabinet, coloured of size 300 x 450 mm fixed with screw and PVC gutty on wall complete all as specified and directed.

S&F in repair CP brass, soap dish, superior quality complete all as specified and directed.

M&L in repair 15mm angle valves/ stop cock, fancy type, chromium plated , cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair, two way angle valve chromium plated, brass 15mm bore complete all as specified and directed.

S&F in repair CP brass toilet paper holder, superior quality complete all as specified and directed.

S&F Health foucet including PVC pipe 1.20m long with brass nuts for EWC, fixed in repairs complete all as specified and directed.

S&F in repair corner glass self assembly complete all as specified and directed.

S&F in repair Stainless steel towel rack 600mm long with lower hangers complete all as specified and directed.

Demolition and breaking up (salt glazed ware, AC, PVC) drain pipes of any dia set in cement mortar complete.

S&F 75 mm bore PVC (SWR) pipe single socket in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repair Towel ring chromium plated complete all as specified and directed.

S&F in repair vitreous china wash down water closet (single piece with attached cistern) pan pedestal pattern white including connection in drain and in flushing pipe complete including 'P' or 'S' trap and plastic water closet seat cover complete all as specified and directed.

S&F PVC (SWR) Bend 110mm dia with access door complete all as specified and directed.

S&F in repair vitreous china table top wash basin, white, of size 480 X 370mm fixed on granite including cutting for and pinning in ends in CM 1:3 including 32mm dia chromium plated waste coupling complete all as specified and directed. Make: Hindware or Equivalent

S&F in repair stainless steel sink with or without drainage board, made out of 1.00 mm thick stainless steel sheet conforming to AISI 304 with plug, washers, waste pipe, cast iron cantilever brackets, connecting union over all size 950 mm X 510 mm with bowl size 410 mm x 410mm x 230 mm complete all as specified and directed. Make: Nirali/ Blue Star/ Jayna/ Nilkanth.

S&F in repair PVC connection 15 mm bore, 450 mm long complete with both ends unions complete all as specified and directed.

S&F in repair Brass chromium plated bottle traps 32mm for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified and directed.

Taking down existing cement plaster including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on other fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

S&F in repair PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls, 110mm bore complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of wall and applying two coat of exterior emulsion paint (Apex/Weather coat) white or tinted as approved complete all as specified and directed.

Material & labour for preparation of new plastered surfaces of wall with 1-2mm thick wall care putty and applying two coats of Oil bound distemper over a coat of alkali resistant primer complete .

M&L for complete removal of existing finishes of wall including cornices etc by scraping out, washing, rubbing down and stopping of existing plastered or unplastered surfaces surfaces and applying Two coats of oil emulsion distemper white or tinted of approved shade over a coat of white cement based putty 1-2 mm thick complete all as specified and directed.

S&F PVC (SWR) Bend 75mm dia with access door complete all as specified and directed.

S&F in repair Stainless steel plate rack (utensil rack) of size 900 mm x 750 mmx250mm made with 0.63 mm thick stainless steel sheet provided with brass screw including necessary fittings, nut/bolts complete all as specified and directed.

Demolition of cement concrete reinforced of any description and in any position not otherwise specifically provided for incl removing rubbish off the premises complete all as specified and directed.

M&L for Rendering 10 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified and directed.

M&L for Preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for Preparing old plastered or unplastered surfaces of ceiling and applying one coats of white wash complete all as specified and directed.

M&L for RCC nominal mix type B1 1:2:4 (using 20 mm graded aggregates) in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

S&F in repair 15mm bore, CP Bib taps fancy type long body , half / full turn , screwed down for iron pipes complete all as specified and directed. Make: Jaguar or Equivalent

M&L for RCC nominal mix type B-1 1:2:4 (using 20 mm graded crushed stone aggregates) Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for preparing old plastered decorated surfaces of wall and applying two coat of exterior emulsion paint (Apex/Weather coat) white or tinted as approved complete all as specified and directed.

S&F in repair 25mm dia stainless steel Drapry rod fixed with decorated brackets and with end knobs complete all as directed and specified

M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent ot shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Description same all as per Item No 87 here in above, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L Marble work Udaipur Green or any approved colour 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 10mm thick rendering in CM 1:4 complete all as specified and directed by Engr-in-charge.

M&L for applying two coat of Dr Fixit sure ceal damproof chemical on plaster/unplastered surfaces complete all as specified by the manufacture . Make- pedilite and equivalent of johnson.

M&L for Forming jambs in CM 1:6, etc. To openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete all as specified and directed.

Excavation in trenches in soft/loose soil n.exc 1.5m depth and n.exc 1.5m in width for foundation etc and getting out all as specified

Returning filling in, including spreading, levelling, watering and well ramming in layers n exc 25 cm soft/ loose soil complete all as specified and as directed.

Spreading and levelling of soil in layers not exc 25cm thick with watering including well remming as required for filling under floor complete

Removing of surplus excavated soil to a distance not exceeding 50M and deposited where directed at a level not exceeding 1.5M above the starting point all as specified.

M &L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate in foundation, filling and mass concrete. Complete all as specified and directed

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed .

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

M&L for Making good under cills or over arches, lintels and bressummers. including allpinning in CM 1:6 when necessary complete all as specified and directed.

Surface dressing n exc 15 cm deep in soft / loose soil and getting out exceeding 50 Mtr in soil complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in chajjas, shelves etc and the like, complete all as specified and directed.

All as per serial item No 97 here in above for each additional 1.5m or part thereof in depth beyond the first 1.5 mtr complete all as specified and directed.

M&L M-25 (Design mix) Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and directed

M&L for 75 mm thick cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate in plinth protection finished even and smooth without using extra cement including necessary formwork and cutting of joints complete all as specified.

Use and waste for formwork to sides of foundation incl rough finished surfaces of concrete complete all as specified and directed by Engineer-in-charge.

Use and waste for formwork to sides of column incl rough finished surfaces of concrete complete all as specified and directed by Engineer-in-charge.

Use and waste for formwork to sides of slab incl rough finished surfaces of concrete complete all as specified and directed.

Use and waste for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams, etc complete all as specified and directed.

Use and waste for formwork to sides of Chajja incl rough finished surfaces of concrete complete all as

M&L 38 mm width & 3 mm thick glass dividing strips for laying in floor in panels complete as all spfd and directed.

Supply and fixing 1100 volts grade heavy duty cable PVC insulated copper conductor for submain wiring alongwith earth wire with 4x4 sqmm+1x4sqmm earth wire sizes of FRLS is PVC insulated copper conductor, single core cable insurface/recessed as required with 25mm PVC conduit pipe, surface conduit/concealed etc complete all as specified and directed.

Material and labour for making circular holes suitable for fixing of 450mm sweep Exhaust fans by cutting the wall any thickness /required circumstance for exhaust of air and including grouting of rag bolts and nuts complete including finishing of disturbed surfaces by using cement mortar 1:3 complete all as required at site and directed by Engineer-in-Charge.

specified and directed.

Use and waste for formwork to edges of rough finished surface of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M&L for 5 mm thick rendering in cement mortar (1:3), finished even and fair without using extra cement on brick or concrete surfaces of ceiling complete all as specified and directed.

M&L for 10mm thick plaster in (1:4) cement mortar on green concrete surfaces of roof with WPC (WPC should be measured and paid separately) complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) in floor complete all as specified and directed.

M&L for preparation of new plastered surafces of wall and applying two coats of water based preimum acrylic smooth exterior emulsion of approved colour complete all as specified and directed

Supply only liquid water proofing compound ISI marked all as specified and as directed.

S&F for Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam PVC Sheet on the front face & 2mm prelam PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F for solid PVC door frame of size 50mm x 95mm made out of 5mm single side prelam PVC sheet reinforced with MS tube in opening as per specification and shown in drg in SSR Part -II 2010 complete all as specified and directed.

Supply and fixing factory made uPVC any approved colour Three track three panels sliding window with net/grill alongwith fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window not exceeding 2.0 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. Note -1. Glazed shutters float glass thickness not less than 5.00 mm and wiremes shutter with Stainless steel wire mesh 0.36 mm dia with aparture 1.4 mm shall also be deemed included in quoted rates and No extra payment will be made separately. 2. for UPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F for 200 mm long Stainless steel tower bolt complete all as specified and directed

S&F for stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & directed.

S&F for stainless steel handle 200mm long complete fixed with steel screws complete all as specified and directed.

S&F for 250 mm long stainless steel sliding door bolt plate type with bright bolt not less than 12mm dia with & including a min of 6 bolts & nuts four on bolt plate & two on staple plate & fixed complete all as specified and directed.

S&F for 100mm size stainless steel butt hinges complete all as specified and directed.

S&F for rotational moulded,multilayer HDPE water storage tank of 1000 ltrs capacity (Cylindrical vertical with closed top) ISI marked fixed in position on existing places complete all as specified including 02 Nos 20mm dia full threaded GI tank niple, 20 mm dia PTMT float valve epoxy coated Aluminium rod with high density plastic float ball (of minium weight 210 gms) etc complete all as specified and as directed.

S&F for vitreous china wash down water closet pan pedestal pattern white including connection in drain and in flushing pipe complete including 'P' or 'S' trap complete all as specified and directed.

S&F for Plastic water closet seat cover white closed pattern with flat bottom and cover with MS Chromium plated hinge twice ISI marked as approved complete all as specified and directed.

S&F for vitreous china urinal, half stall type (flat back), of size 635x395x420mm, white, with grating and union for discharge pipe (excluding flushing cistern) including 32mm dia PTMT coupling and waste pipe, CP spreader providing and fixing plugs, bedding urinal against wall in CM 1:2, complete all as specified and directed.

S&F for two way bib tap with flange 15mm bore, fancy type, quarter turn, cast copper alloy, chromium plated with long shank and cup screwed down, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F for 15mm dia health faucet ABS body with 08mm dia , 01 mtr long flexible tube & wall hook complete all as specified and directed.

S&F for CP toilet paper holder fixed to walls with chromium plated brass screws complete all as specified and directed.

Supply and fix/fabrication in repair kitchen cabinet & wardrobe/ cupboard made out of 16 to 18 mm thick PVC board laminated sheet complete. Make : Rajshree or equivalent all as specified and approved by Accepting Officer.

S&F for 20mm dia Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F for 15mm bore angle valve CP wall with quarter turn flange, brass chromium plated fancy type complete all as specified and directed.

S&F for 10 litre capacity PVC low level cistern ‘ white’ with inlet, float valve including bracket with 32mm dia PVC pipe 600 mm long complete all as specified and directed.

S&F for PVC connection 450mm long and15 mm dia with brass fly nut at both ends complete all as specified and directed.

S&F for 5mm thick looking mirror with bevelled edges including suitable SS studs complete all as specified and directed

S & F CP bottle trap (with internal partition 32 mm Size with 300 mm & 190 mm long wall connection pipe and wll flange complete all as specified and directed.

S&F for Tubular towel rail of brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flanges complete all as specified and directed.

S&F for PVC (SWR) 110mm bore pipes single socketed, in any length with rubber ring joints, laid in tranches or in floors complete all as specified and directed.

S&F for PVC (SWR) 110mm bore bend, any radius complete all as specified and directed.

M&L for hardcore of gauge n exc. 63 mm,of broken stone deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

S&F for PVC (SWR) junction single (single T), equal or unequal, 110 mm bore, provided with access door complete all as specified and directed.

M&L for Glazed ceramic coloured tiles 6 to 7 mm thick area of tile 300mm x 400mm / 300mm x 600mm in skirting, dados, risers to steps, etc se and jointed in neat cement slurry, and pointed in coloured cement to match tiles over and including 10mm thick rendering or backing layer in cement mortar 1:4 complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls/ceiling and applying white cement based wall care putty (Birla/JK white) on the surfaces with minimum 1 to 2 mm uniform thickness making surface absolutely smooth by grinding with sand paper and applying two coats of oil emulsion distemper complete all as specified and directed.

M&L for PCC (1:4:8), type D-2 (using 40mm graded stone aggregate) as in sub base 100mm thick complete all as specified and directed.

M&L for 75mm thick PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate in sub base of floor complete all as specified and directed.

M&L for sand cushion for paver blocks complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B-1 (using 20mm graded crushed stone agg) in floor complete all as specified and directed.

M&L for joint free non skid, ceramic “coloured” tiles 7 to 8 mm thick area of each tile of size 300mm x 300mm in floor, shelves etc, set and jointed in nea

t cement slurry & pointed in coloured cement to match the shade of tiles over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft/loose soil complete all as specified and directed.

M&L for rubber moulded chequered cement concrete coloured tile 30cm X 30cm X 25 mm thick with grey cement and pigment set jointed and pointed in neat cement siurry over screed bed or bedding layer 15 mm thick in CM (1:6) in floor complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L Cement concrete as in foundations/ drains & channels Type C-2 1:3:6 (using 40 mm graded crushed stone aggregate) complete all as specified and directed.

M&L for cement concrete type B-1 1:2:4 (using 20mm graded crushed stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified and directed.

M&L for Fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

M&L for Fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc, (Exceeding 30cm) complete all as specified and directed.

Supplying and applying High build elastomeric waterproofing coating based on pure, hydrophobic polyurethane, cold applied of spray / brush applied, SmartCare PU Magnum membrane with an elongation of 550% and tensile strength of 2.5 N/mm2 as per ASTM D 2370, crack bridging ability of 3mm as per ASTM C1305, no leakage upto 7 bars of water pressure as per DIN 1048, shore A Hardness of min. 45 as per ASTM D 2240. The system includes final base preparation, epoxy primer application and applying SmartCare PU Magnum or approved equivalent in two coats with a consumption of 1.5 Kg per SQM on a primed surface with SmartCare Primer and a 40 GSM geo textile cloth sandwiched in between, etc., complete as per Manufacturer's specifications

M&L for removing excavated material n exc. 500m and depositing where directed at a level n exc. 1.5 Km above the starting point complete all as specified and directed.

M&L for Providing precast cement concrete in landings, perforated cover slabs (for man holes etc.) Type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) complete all as specified and directed.

S&F for Mild steel TMT bars 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for brick work with fly ash brick built in cement mortar (1:4) straight or curved on plan exc 6m mean radius for man holes complete all as specified and directed.

M&L for concrete bed to drain pipes in PCC (1:3:6) type C-2 using 40mm graded stone aggregate including packing under and haunching against the sides of pipes after are laid in step and tested for 150 mm bore sewer line (excavation and earth work for sewer pipe line measured and paid separately complete all as specified and directed.

Taking down carefully aluminium / copper point wiring any type for one light , fan, socket power point or buzzer controlled by one switch complete including fitting / fixtures such as switches, ceiling roses, holder, socket, light fitting etc, for credit and making good disturbed surfaces of walls, ceilings etc complete all as specified and directed.

M&L for point wiring with concealed in wall 2.5 sqmm (nominal area) FRLSH PVC insulated stranded copper conductor single core including non metalic PVC conduit medium grade of appropriate size concealed in wall and modular sunken box, cover plate/frame any module as required at site with all accessories as specified including 2.5 Sqmm FRLSH PVC insulated unsheathed multistranded copper earth conductor to common earth and connected to earth dolly for fan / light / exjaust fan/ bell point controlled by one switch and single conduit shall be used for each circuit complete all as specified and directed. Note :- 1. Cost of PVC conduit, with connected item to be included in the quoted rate. 2. M&L for cutting chases on walls / ceiling and making good disturbed surfaces including finishing with cement mortar (1:3) etc; are deemed to be included in the quoted rate. 3. Modular metal box, cover plate & frame for any module to be included in the quoted rate.

All as per item No. 174 here-in- above but for 3 pin 5 Amps switch socket on independent board with 2.5 sq mm copper cable complete all as specified and directed.

All as per item No. 174 here-in- before but for 3 pin 15 Amps switch socket n on independent board with 4 sq mm copper cable including 4 Sqmm FR PVC insulated unsheathed multistranded copper earth conductor to common earth complete all as specified and directed.

All as per item No. 174 here-in- before but for 3 pin 15 Amps switch socket on independent board with 2.5 sq mm copper cable including 2.5 Sqmm FR PVC insulated unsheathed multistranded copper earth conductor to common earth complete all as specified and directed.

All as per item No. 174 here - in - before but for 5 Amps socket point on the same board controlled by one switch complete all as specified and directed.

S&F for modular switch 1 way, 6 amps, 230V AC, one way complete all as specified & directed.

S&F for modular socket out let 2-in-1, 3 pin, 6 amp flush type 2 module complete all as specified & directed.

S&F for modular socket out let 2-in-1, 3 pin, 5 & 16 amp flush type 2 module complete all as specified and directed.

S&F for modular switch flush type 16 amps, 230V AC single pole one way complete all as specified and directed.

Supply & fixing energy efficient LED light of 10 Watt of length - 02 Feet long, wide voltage protection range 140-270 Volt AC housed in extruded aluminum housing (enhances safety) with high quality polycarbonate diffuser including making connection with two core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed.

S&F for modular bell push flush type 6 amp, 1 module SP , 230V AC complete all as specified & directed.

S&F for ceiling rose surface backelite three terminals complete all as specified and directed.

S&F for call bell Dingdong type AC 230 Volts single pole complete all as specified and directed.

S&F for modular fan regulator, 5 stepped, electronic type, single phase, 120 watt, socket size incl connection complete complete all as specified & directed.

S&F 4mm thick E-boards tiles (Make: Everest) false ceiling with powder coated GI snap grid frame work (Make : Armstrong/metacil or equivalent as approved) complete all as specified and directed including all necessary drilling, cutting, making good and necessary arrangement to fix electrical items as under:- (a) 25x25x1.5mm thick GI angle powder coated plugged @ 600mm centre to centre along perimeter of wall. (b) 25x25x1.5mm thick GI tee powder coated as main and cross runners suspended with 1.6mm dia GI wire suspenders with adjustable clamps and dash free fastners plugging in RCC slab placed @ 600mm centre to centre from perimeter of wall. (c) Fixing of 4mm thick E-boards tiles of size 595x595mm of approved texure and finished complete with two coats of oil emulsion distemper on ceiling.

S&F for LED tube light fittings (inverter type) decorative ultra slim linear fixture,20 Watt, efficiancy 120 Lm/watt ,4 feet,surface mounting type extruded pvc, snap on installers and domestic electronic Driver ,connector block ect.with all assoceries intenallt prewired & includingconeecting up with 2 core flexible cppper conductor cable with sutable size & suitable for and mounting clamps complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F for Lamp holder insulated body PVC/polycarbonate with back plate and 9 W LED bulb inverter type suitable for batten fitting complete all as specified and directed

Supply & fixing wall mounted fitting fancy type (City-2 type) with 9 watt LED bult inverter type including making connection with two core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed.

S&F on wall building security light luminaire for 1x35 w LED with deep drawn housing complete with and including cable for connection from ceiling rose with 3 core 1.5 Sqmm PVC insulated stranded copper conductor including bracket made out of 32 mm bore GI Light grade 1.20 M long to required shape as in bracket for to shape fixed on wall/pole with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers including painting complete and taking down unserviceable one complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louver

M&L in replacment of two single core (submain) FRLS PVC insulated cable of 6.00 Sqmm nominal dia and one single core green PVC insulated copper conductor earth continuity cable of 6.00 sqmm nomianal dia as mentioned below is drawn in and including non metallic, medium duty, rigid PVC conduit not less than 20 /25mm dia concealed in wall including all conduit and fixing accessories including cutting chases & making good to disturbed surfaces with cement mortar ratio of 1:4 and colour wash complete all as directed. Note :- (I) The cost for cutting, chases required and suitable lugs shall deemed to be included in the quoted unit rate. (II) Two run of submain wire, one run of earth wire and one run of PVC conduit shall be measured one RM

s including antidust painting complete including cutting holes on wall, making good and finishing of disturbed surfaces matching with the exisitng surfaces, necessary fixing arrangements such as fastener bolts, nuts, washers etc of appropriate size complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron wire 4mm dia as earth lead wire by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in Electrical plate No. 3, MES SSR Part I- 2009 with 15 mm dia medium grade GI pipe as a protection to earthing lead and 20 mm dia medium grade GI pipe for watering purpose including excavation & earth work in any type of soil, funnel, wire mesh, RCC pit with cover, cast iron frame complete and connected to earthing test point all as specified or indicated including testing on completion. Note : (i) The concrete pit shall be PCC (1:3:6) type C-1, 40mm thick precast cover slab of RCC with suitable Mild steel handle in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I (ii) PCC pit shall be provide at least 500 mm away from the earth pit and not on just on the eath pit and extra cost of additional length of water pipes and fittings junction etc shall be deemed to be included in the rate. (iii) Item includes the cost of 7.5 metre earth lead wire and GI pipe for protection of earth wire. Any varriation in quantity shall be adjusted.

S&F for 60cm auto clean wall mounted chimeny with stainless steel baffle filters, push button control, exhaust flexible pipe as per site requirement complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m including including cutting holes on wall, making good and finishing of disturbed surfaces matching with the exisitng surfaces, necessary fixing arrangements such as fastener bolts, nuts, washers etc of appropriate size complete all as specified and directed.

S&F ventilators with net and grill, single or multi shutters turn window and made out of upvc multi-cavity frame sections of 60x60x2.5mm suitable reinforced and double multi shutters division are made by using sash mullion having 50x64x2.5mm multi cavity upvc section, suitable and reinforced and GI and shutters are made out of 50x85x2.5mm upvc section,reinforced and welded in corner with EDPM gasket provision for glass and for air tight at frames and outer side of shutter with single glazed window and adjusting suitable glass bead with perfect hardware like hinges,handles,stays etc complete mosquito mesh shutters is made out of UPVC extruded section of 61x27x2mm with GI channel of 1.20mm thick welded in corner mosquito net of GI is fitted in shutters with proper required accessarry like,hinge MS grill of 12mm round pipe are inserted in main frame and screw by hidden screwing system with powder coating etc complete all as specified and directed. Note:Glazed shutters glass thickness not less than 3.00mm and wire mesh shutters with SS wire mesh as approved by Engr-in-Charge is also included and no payment will be paid separately.

Per Point

One light/fan/bell point controlled by one switch

One point for socket outlet 5 amps on independent board

Supply and fixing in replacement of factory made epoxy polyester powder coated distribution board VTP & N 4 way (vertical load line distribution board) with metal double door (IP-43 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates including 4 pole MCCB 100Amp 25 KA - 01 fixed type Nos and SP MCB 63 Amps 'C' curve 10 KA - 12 Nos outgoings complete all as specified and conforming to IS: 8623 along with cable end box for above DB complete all as specified and directed. NOTE :-(a) MCB and MCCB cost shall be included under respetive item of sch. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F in replacment of factory made, sheet metal enclosure distribution boards, double door type, protection class ( IP-42), suitable for mounting MCBs confirming to IS-13032, IS-8623, BS-5484 with min 200 Amps rating copper bus bar ,SP&N 8 ways ,220 volts complete all as specified and directed. Note: MCB/ shall be measured and paid seperatly under respective item of this schedule

Supply and fixing in replacment of 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing in replacment of 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and neutral current carrying capacity 40/63 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

M&L in replacment of four single core (submain) FRLS PVC insulated cable of 10.00 Sqmm nominal dia and one single core green PVC insulated copper conductor earth continuity cable of 10.00 sqmm nomianal dia as mentioned below is drawn in and including non metallic, medium duty, rigid PVC conduit not less than 20 /25mm dia concealed in wall including all conduit and fixing accessories including cutting chases & making good to disturbed surfaces with cement mortar ratio of 1:4 and colour wash complete all as directed. Note :- (I) The cost for cutting, chases required and suitable lugs shall deemed to be included in the quoted unit rate. (II) Two run of submain wire, one run of earth wire and one run of PVC conduit shall be measured one RM

Supply and fix electric water heater, storage type steel body with inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed.

One point for socket outlet 5 amp same board

Supply and fixing wall mounting fan 400mm, 230 V. Five star rated complete as specified and directed.

M&L for Shifting and refixing of split type AC (Indoor and Outdoor units) of any make and any type after servicing and charging of gas (M410a/R134a/R-22/R32) by testing the leakage in system by filling of Nitrogen gas upto 300 PSIG and repairing of leaking spot/joints with gas welding work, cleaning and flushing out the complete system with gas, supply and replacing of drier/filter, copper pipe with insulation, making the complete system leak proof, vacuuming the system as existing and testing etc complete all as specified & directed. Note :(a) Dismantling and refixing of split AC are including in quoted rate. (b)Drier capillary,copper tubing,refrigernt gas,Insulation and LDPE pipe are inclusive in quoted rate.(c) (i) Quoted rates deem to be included cost of drain pipe, copper tubing and 2.5 sqmm multi standard copper cable (all 3 mtr length) etc (d) making hole and filling the hole on wall with PCC (1:2:4) type BO (Using 12.5mm graded stone aggregade, 15mm thick rendereing in cement mortar (1:3) good the disturbed surface with existing colour matching are inclusive in quoted rate.

M&L for energy saver LED battan fitting 20 watt,120 Lumen /watt, 230 Volts, single tube mounting including with electronic driver LED Printed board, end cover, connector box etc and accessories, prewired, LED including required fixing arrangements and electrical connection two core copper cable from ceiling rose to

All as per Item No 205 here in above but for one socket outlet 16 Amp on independent board with 4.0 Sq mm cable and 4.0 Sq mm earth wire complete all as specified and directed.

M&L for energy saver LED battan fitting 10 watt, 230 Volts, single tube mounting including with electronic driver LED Printed board, end cover, connector box etc and accessories, prewired, LED including required fixing arrangements and electrical connection two core copper cable from ceiling rose to led light fitting all as directed . Make Philips/Wipro/ Havells or equivalent as approved by GE

One 3/5 pin socket outlet, 6 Amp on the same board with other switches complete all as specified and directed.

Each Job

S&F for sheet metal enclosure for MCB's 240 volt 8 way single pole and neutral with rated bus bar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S&F for sheet metal enclosure for MCB's 240 volt 4 way single pole and neutral with rated bus bar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

M&L for single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps 240 volt capacity complete all as specified and directed.

Supply & fixing ISI marked switch piano flush button type, single pole, one way, 6 Amps, 240 volts for point wiring complete all as specified and directed .

S&F in repair vitreous china counter top sunk type wash basin, white, oval shape of size 600x400x185mm fixed on granite including cutting for and pinning in ends in CM 1:3 including 32mm dia cp waste coupling including fixing of swan neck pillar tap, waste fitting etc complete all as specified and directed.