PROVISION OF OVER HEAD RAIN SHED FROM P-310A TO P-311 SENTRY AT TCP I AND FROM 108 MTN BDE CAMP TO JCOs SINGLE LIVING ACCN AT BRICHGUNJ MIL STN PORTBLAIR UNDER GE BRICHGUNJ

Amount

Surface dressing n exc 15 cm deep and getting out hard/Dense Soil complete all as specified and as directed.

Excavating over areas, n exc 1.5 m deep and getting out Hard/Dense Soil complete all as specified and as directed.

All as per item No 2 here in before but over 1.5m depth and not exc 3m

Excavation in trenches not exceeding 1.5M wide and not exceeding 1.5M in depth for laying pipe line, replacing sluice valve etc and getting out in hard / dense soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5M wide and not exceeding 1.5M in depth for laying pipe line, replacing sluice valve etc and getting out in soft / loose soil complete all as specified and as directed.

Material and labour for Excavating in post holes (or similar holes) each n exc 0.5cu. m, getting out in Hard/Dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, all as specified and as directed

Material and labour Filling under floors or in foundations including watering and consolidation all as specified and as directed. Note: Approved soil obtained from excavation shall be re used.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft / loose soil including making good of disturbed surfaces complete all as specified and directed.

Removal of extra excavated soil not exc 50m and depositing where directed at level not exc 1.5m above the starting point all as specified and as directed

Material and labour for Forming embankments incl raising or lowering etc not exc 30cm thick, watering, ramming/rolling etc not exc 1.5m high from base all as specified and as directed

Material and labour for Hard Core 150mm thick (compacted thickness), with coarse aggregates of grading 3 (50 to 20 mm size), spread, rolled and consolidated to gradient and camber required all as specified and as directed

Material and labour Hard core of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 10cm thick, watered and rammed to a true surface complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Material and labour for Plain cement concrete 1:4:8, Type D2, (using 40mm graded stone aggregate), 100 mm thick in sub-base concrete to pavement all as directed by Engineer-in-Charge

Material and labour 75 mm thick PCC 1:4:8 Type D-2 (using 40mm graded stone aggregate) as in sub base for floors all as directed by Engineer-in-Charge

Material and labour 75 mm thick PCC 1:3:6 Type C-2 (using 40mm graded stone aggregate) as in sub base for floors all as directed by Engineer-in-Charge

Material and labour 40mm thick Cement concrete 1:2:4 Type B-1, (using 20mm graded aggregate) as in plinth protection all as directed by Engineer-in-Charge

Material and labour for 40mm thick Damp proof course in cement concrete 1:2:4 type B-0 (using 12.5mm graded aggregate) to horizontal or vertical surface including necessary formwork complete all as specified and as directed

Material and labour Cement concrete 1:4:8 Type D-2 (40mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

Material and labour for Plain cement concrete 1:2:4, Type B0, (using 12.50mm graded stone aggregate) for Kerbs, cover slabs etc including weathering slightly chamfered angles all as directed by Engineer-in-Charge

Material and labour for Cement concrete (1:3:6) Type C2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed

Use and waste for formwork flat or curved to sides of concrete foundations, footings, bases of columns, and plinth beams and similar work vertical or to batter complete all as specified and as directed

Use and waste for formwork flat or curved to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed

Use and waste for formwork flat or curved to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

Use and waste for formwork for walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings, etc. complete all as specified and as directed

Material and labour Reinforced cement concrete M-30 (design mix) as in Foundations footings, plinth beams, bases for columns, etc and mass concrete complete all as specified and as directed

Material and labour Reinforced cement concrete M-30 (design mix) Columns, pillars, piers, posts and struts complete all as specified and as directed

Material and labour Reinforced cement concrete M-30 (design mix) Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed

Material and labour RCC type B1 1:2:4 (using 20 mm aggregate) on Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses complete all as specified and as directed

Material and labour 8mm dia TMT bars, cut to length and bent to shape required, including cranking and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed

Material and labour for TMT bars 10mm dia and over as in reinforcement, cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing clips etc, complete all as specified and as directed.

Material and labour Fe 410 -W (GdeE- 250) quality "A" Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated)

Supply and fix Mild Steel work in tubular trusses and tubular posts/ purlins including special shaped washers etc., complete using ERW or induction butt welded tubes conforming to IS :1161-1979 grade st-240 including notching, drilling, fitting, riveting and/or welding or connecting with bed plate, bolt and nuts complete all as specified and as directed by Engineer -in-Charge

Supply and fix for wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directe

Supply and fix Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed by Engineer -in-Charge

Material and labour Fe 410-W(Gde-E-250) quality -A , roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc

Material and labour for preparation of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer -in-Charge.

Supply and fix of 0.63mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 as specified

Supply and fix pre painted galvalume aluminium zinc coating GI based semi-corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self-tapping screws etc complete all as specified and as directed

All as per item No 40 here in before but plain sheet as in ridge, valley gutter etc.

Material and labour pre-cast cement concrete masonry in PCC 1:3:6 type C1 using 20mm graded aggregate with solid block, exceeding 10cm in width setting in CM 1:6 complete all as specified and as directed

Material and labour for 15mm thick external rendering in two layers of 5mm thick in CM (1:4) mixed with water proofing compound (water proofing compound shall be @3% weight of cement) over and including a coat of 10mm thick in CM (1:6) over brick or concrete surfaces finished even and fair. Note: Rate inclusive of supply of WPC.

Material and labour for 10mm thick rendering in CM 1:6 on bric or concrete surfaces all as specified and as directed by Engg-in-Charge

Material and labour for Rendering in CM 1:6, 15mm thick on fair faces of brick masonry, finished even and smooth using extra cement

Material and labour for two coat of weather proof exterior acrylic emulsion paint with anti-fungal property over a coat of primer on newly plastered wall surfaces including preparation of surfaces etc complete all as specified and as directed.

Material and labour for applying two coats of oil bound distemper over a coat of alkali resistant primer on newly plastered surfaces of wall including preparation of surfaces complete all as specified and as directed

Material and labour for polished kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including screed bed of 15 mm thick in CM 1:6 complete all as specified and directed.

Material and labour for polished kota stone slab 20-25 mm thick in vertical surfaces as in steps, riser, dado etc laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including backing coat of 10 mm thick in CM 1:4 complete all as specified and directed.

Material and labour for Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed of 15 mm thick in CM 1:6 complete all as specified and directed.

Material and labour for Glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick backing coat in CM 1:4 all as specified and as directed by Engg-in-Charge

Material and labour for Machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35Grade with grey cement and pigment over and including 50mm thick Sand filling under floors including watering and consolidation all as specified and as directed

Material and labour for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments over and inclduig 15mm thick screed bed in CM 1:6 all as specified and as directed by Engg-in-Charge

Supply and fix Aluminium powder coated (minimum thickness is 50 microns) Door / window / Ventilator/partition frames and shutters (02 Nos glazed & gauzed), side hung type, without sash bars, standard aluminium grills, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, locking arrangements etc., complete with standard aluminium sections, complete all as specified and as directed by Engineer-in-charge.(Aluminium section shall be of make Jindal/Hindalco/ Indalco). (Note:- Weight of various Aluminium sections handles and locking arrangements shall only be considered for measurement for payment. However cost of rubber packing given in the item shall be deemed to be included in the rate quoted. Glass panels, prelaminated particle boards, aluminium wire cloth as applicable will be measured and paid separately as supplied only).

Supply and fix Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing.

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC `C' channel having at PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

Supply and fix 150mm long extruded aluminium alloy anodised handles fabricated type all as specified and as directed

Supply and fix 100mm long extruded aluminium alloy anodised handles fabricated type all as specified and as directed

Supply and fix Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing clips to sheet cast or extruded sections and fixing bolt or cast aluminium alloy all as specified and as directed

Supply and fix Aluminium anodised barrel tower bolt of extruded section of size 150mm long all as specified and as directed

Supply and fix Aluminium anodised barrel tower bolt of extruded section of size 100mm long all as specified and as directed

Supply and fix Aluminum anodised butt hings 100 mm long extruded alluminum, alloy with galvanised mild steel hinge pin, type C-21

Supply and fix Aluminum anodised butt hings 75mm long extruded alluminum, alloy with galvanised mild steel hinge pin, type C-22

Supply only 4mm thick sheet glass ordinary quality and glazing with rubber packing around the glass, in squares n. exc 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-charge.

Supply only 4mm thick figured glass ordinary quality and glazing with rubber packing around the glass, in squares n. exc 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-charge.

Supply only 12 mm thick Prelaminatd particle board, exterior grade, prelaminated exterior grade on both sides with decorative choice lamination and fixed to aluminium frames complete all as specified and as directed by Engineer -in-Charge.

Supply and fix rotational moulded polyethylene water storage tanks 500 ltrs capacity (cylindrical or vertical with closed top) hoisted and fixed in position, complete all as specified and directed by Engineer-in-Charge

Supply and fix 20mm dia nipple of PTMT, suitable for HDPE water tank, min weight 45 gms, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, minimum weight 142 gms, complete all as specified and directed by Engineer-in-Charge

Supply and fix gun metal globe or gate valve, 20mm dia, screwed down high pressure with iron wheel head, screwed both ends for iron pipes or for union complete all as specified and as directed by Engineer-in-Charge

Supply and fix vitreous china water closet, pedestal type, white including flush pipe, seat cover etc, including connection to drain (or out going pipe) and to flushing pipe anti syphonage pipes etc complete all as specified and as directed by Engineer-in-Charge

Supply and fix vitreous China wash hand basin, 'OVAL TYPE' 550 mm including with single tap hole CP pillar cock of 15 mm dia brass CP chain and rubber plug , waste pipe and PVC connection.

Supply and fix PVC low level flushing cistern,10 litres capacity, including PVC flush pipe of required length, 15 mm bore ball valve and PVC connection 300 mm and other accessories, complete all as specified and directed.

Supply and fix 110 mm dia PVC (SWR) Pipe single socketed in any length with rubber ring joint laid in trenches/fixed on floor/walls including jointing with solvent cement all as specified and directed by Engineer -In-Charge.

Supply and fix PVC waste pipe, 32mm dia, for WHB, complete all as specified and as directed by Engineer-in-Charge.

Material and labour PVC (SWR) multi floor trap with grating including jointing with solvent cement with 75 mm outer dia

Material and labour for UPVC 75 mm dia Nahani trap/floor trap with PVC grating complete all as specified and directed.

Supply and fix Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms)

Supply and fix for Soap dish, vitreous China white, approximate size 160x 160x90mm embedded in the wall all as specified and as directed

Supply and fix for 20mm bore UPVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe all as specified and as directed

Supply and fix 15 mm bore pillar tap cast copper alloy with capstan heads chromium plated screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes all as specified and directed.

Supply and fix 15 mm bore Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

Supply and fix 15 mm bore fancy type, chromium plated with long shank and cupe (concealed type) Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

Supply and fix in PVC connections 15mm size with PTMT nuts of length 600mm all as specified and as directed

Material and labour PCC 1:3:6, Type C2 (using 40mm graded stone aggregate), concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested all as specified and as directed

Material and labour Salt-Glazed stone ware drain pipes, 150mm dia (internal dia) laid in trenches and jointed as specified

Material and labour PCC 1:2:4, Type B1, (using 20mm graded stone aggregates) for Coping and haunching concrete all as specified and as directed

Material and labour Point wiring complete with 1.5 sqmm single core FRLS PVC insulated and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC conduit and all accessories fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm copper cable green in colour as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls, with 3mm thick laminated sheet top cover for housing the switches, socket outlets, fan regulators etc., for One light point controlled by one switch.

All as per item No 89 here in before but One fan point controlled by one switch and one regulator

All as per item No 89 here in before but One three pin 5 Amp switch socket cum on same board

All as per item No 89 here in before but One three pin 5 amp switch socket outlet multipurpose on independent board

Supply and fix switch piano flush button single pole one way 5 amp.

Supply and fix switch socket outlet 3 & 2 pin (mult pin) 5 amps flush/box type, complete all as specified and as directed by Engineer-in-Charge

Material and labour for ceiling rose surface Bakelite 65 x 50mm 3 terminal complete all as specified and directed.

Supply and fixing energy efficient LED Smart bright batten 22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core sheathed cable from fitting to ceiling rose all as specified and as directed. Make : Philips Cat No BN021C LED20S PSU CDL/NW GR or eqvt in make of Bajaj/Wipro.

Supply and fix Street light New generation energy saving & environmental friendly long life versatile pressure dia cast aluminium IP65 road way luminaire with high power LEDs 25 w as light and electronic driver complete all as per Philips Cat No BRP020 LED HP/ CW 240 v or equivalent model of Wipro / Bajaj/Crompton with necessary brackets (made out of 25 mm bore GI light grade pipe approx. 0.6 M long) nuts, bolts etc to be fixed as on walls complete as directed.

Supply and fix exhaust fan suitable for on working of AC 230 V ,50 Hz 300 mm sweep 1400 RPM, with heavy duty motor ,incl louvers complete all as specified Make: Havells/Crompton/Orient

Supply and fix ceiling fan suitable for working on AC 230 volts, 50 Hz,1200 mm sweep 5 star rating with down rod and canopy colour of milky white including suitable fan hook anchor flasher for fixing of fan on ceiling complete all as specified and as directed. Make:Havells or equivalent Crompton/Usha

Supply and fix metal enclosure distribution board SPN, 4 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs, including taking down old MCB/DB, complete all as as specified and as directed by Engineer-in-Charge Make :Legrand/C&S/L&T Note:- Incoming & Outgoing connections from the DB shall be provided with proper lugs/thimbles etc...

Supply and fix metal enclosure distribution board SPN, 2 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs, Complete all as as specified and as directed by Engineer-in-Charge Make :Legrand/C&S/L&T Note:- Incoming & Outgoing connections from the DB shall be provided with proper lugs/thimbles etc...

Supply and fix MCB single pole 240 volts, 0.5 to 32 amps complete all as specified and as directed by Engineer-in-Charge Make : Legrand/C&S/L&T

Supply and fix MCB SPN, 240 volts, 6 to 32 amps C series complete all as specified and as directed by Engineer-in-Charge Make : Legrand/C&S/L&T

Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers, bends etc of size 50 mm OD and 38mm ID conforming to IS 14930 -II and ISI Marked all specified and directed.

Supply, lay, test and commissioning underground XLPE insulated and PVC sheathed, armoured heavy duty underground cable, suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminium stranded conductor 1100 volt grade of cross section area 2 Core 6 sq mm

Material and laboour for sub main wiring complete with two runs of 1.5Sqmm FRLS single core PVC insulated unsheathed single core cable 1100 volts grade, multi-stranded with copper conductor (ISI Marked) drawn through and including PVC Conduit and all accessories fixed to wall/ roofs/ floors etc with one run of 1.5sqmm FRLS single core multi-stranded copper conductor as earth continuity conductor, including dismantling unserviceable sub main wiring including accessories, complete all as specified and as directed by Engineer-in-Charge. Note : (1) Two runs of cable one run of PVC Conduit & one run of earth continuity conductor shall be measured as one running metre.

Material and labour for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less thab 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I

Supply and fix 25 mm bore GI tubing medium grade laid in trenches / floor or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing, washing out complete all as specified and directed

Supply and fix 25 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, complete all as specified and as directed

Material and labour for cutting existing 50mm GI line and making branch connection of 40 mm dia GI line complete all as specified and directed

Supply and fix 25 mm bore Gun Metal gate valve with iron wheel head ISI Marked screwed both ends suitable for GI tubing complete all as specified and directed

Sree Tirumala Enterprises

M/s JAS Construction

T.THIYAGARAJAN

B S Grewal

M/s Kamal Electrical

Ravi Enterprises

Hindustan Traders

Bharat Udyog