SPL REPAIR TO DRAINAGE SYSTEM FROM REAR GATE TO MAIN GATE AT CSR IN SUKNA MIL STN AND CERTAIN OTHER SANTIONED WORKS UNDER GE SUKNA IN SUKNA MIL STATION

Amount

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Excavation in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning filling in and ramming earth in layers not exceeding 25 cm thick, watering and removing surplus soil to a distance not exceeding 50m and making good in soft/loose soil complete all as specified and directed.

Surface dressing not exc. 15 cm deep as in soft / loose soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M & L for Hardcore of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or broken boulders complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L providing PCC 1:2:4 type B1, (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M&L for Reinforced Cement Concrete Type B-1 1:2:4 (using 20 mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, deck slabs and in shelves and the like complete all as specified and directed.

M&L precast reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) in landing, cover slabs (for manholes etc), chullah hoods, chajja, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar 1:6 complete all as specified and as directed.

M & L for providing reinforced cement concrete 1:2:4, Type B-1, Nominal Mix using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, bases for columns, basement slabs, under-reamed piles and mass concrete complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing Reinforced cement concrete (1:2:4) Nominal Mix using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m span and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing Reinforced cement concrete 1:2:4, Type B-1, Nominal Mix using 20 mm graded stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

Supply only liquid water proofing compound complete all as specified and directed.

M & L for brick work with sub class ‘B’, old size brick straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, old size straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved on plan to any radius, built in CM 1:6 as in half brick except bricks complete all as specified and directed.

M & L for use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exc. 200 mm thick horizontal or slopping in rough finished flat surface of concrete complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in square,rectangular orpolygonal , rough finished surface of concrete complete all as specified and directed.

M&L for rough finished flat Form work to edges of concrete flats, treads, breaks infloors, window cills, concrete railings, openings in concrete walls floor and roofs not exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or slopping and similar work exc 10 cm but n.exc 20 cm wide as rough finished surfaces of concrete complete all as specified and directed.

S & F 30 mm thick First class hard wood (Sheesham) Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. size of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkhats complete all as specified and directed. Species of timber :- Gamari (Gnelina arborea) / Chickerassy (Chukrasia Tabularis) / Siris (Albizzia procera) / Kalasiris (Albizzia Odoratissima)

S&F 30 mm thick medium density fibre (MDF) board flush door shutter, both side laminated of approved colour, interior grade complete all as specified and directed. Make:- Greenply Industries Ltd. / Balaji Action Buildwell / Novapan / National / Kitply

Taking down chowkats or frame n.exc 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frame but exc. 1.5 Sqm but not exc. 4.0 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

S & F of 150 mm long Aluminium anodised barrel tower bolts, of extruded section complete all as specified and directed. Make:- M/s Aluminium Udyog (Global) / M/s Trisul Industries / M/s Argent Industries

S&F 300 mm long mild steel sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed. Make:- M/s Mowjee / M/s Crown / M/s Everite / M/s Harrison

S&F 150 mm Aluminium handles cast type, anodised and fixed complete all as specified and directed. Make:- M/s Aluminium Udyog (Global) / M/s Trisul Industries / M/s Argent Industries

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned stacks, or stainless steel wire staples complete all as specified and directed.

M&L for mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S & F of mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other or screwed both ends, each screwed ends to be fitted with washer and one hexagonal or square nut, exc. 10 cm and not exc. 15 cm long and 11 to 15 mm dia of shank complete all as specified and directed.

S & F of roof trusses (framed), trussed, purlins, crane gantries, rails, fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections), including distance pieces, cleats etc. confirming to Fe – 410 – W(Gde E - 250) quality 'A' including one shop coat of zink chromate primer paint including preparation of surface complete all as specified and directed.

S & F of pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed. Make:- AVA Steel Industries / M/s AGEW Steel manufacturers Pvt Ltd / M/s Ajanta Ispat Pvt Ltd Siliguri

S & F of mild steel framed work such as grills, gratings etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe – 290 Gde E -- 165 complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars but 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S&F rolled mild steel in plates, gusset plate (plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410W (Gde-E-250) quality-A complete all as specified and directed.

S & F of rolled mild steel sections as in framing of cladding, glazing, door or gates and the like fixed with angle cleats and connecting plates etc. confirming to Fe – 410 – W(Gde E - 250) quality 'A' complete all as specified and directed.

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

M&L powder coated Aluminium anodised door, window, Cup board and ventilator shutter and frame any type (Sliding or openable ) with frame and other similar work, fabricated aluminium mesh etc. aluminium heavy section favricated incl all necessary roller wheels, cleats, handle, locking arrangement and arrangement to fix wire mesh with aluminium channel beading and stainless steel screw incl cost of rubber gasket ,beading roller wheel etc. ,complete all as specified and directed. Make:- M/s Halco Aluminium Extrusion / M/s Bhagwati Sai Metal Alloys / M/s Argent Industries Note: (a) The weight of rubber gasket beading, roller wheels, etc will not be measured with the weight of aluminium shutters as only aluminium items shall be measure. (b) Wire mesh shall be measured and paid separately. (c) Aluminium hinges shall be included in the unit rate

S&F in replacement 4 mm thick pre-painted E-fibre board Designer/Decorative fixed or laid/ inserted to with and including Anodised aluminium snap grid frame size 605x605 mm work for false ceiling Hangers with 6 mm dia. G.I. (length as required) adjusting level fixed to roof slabs/truss by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long including necessary dimantling of existing unserviceable ceiling boards of any thickness including cover fillets complete all as specified and directed. Make of boards:- Everest / Visaka Industries / Lafarge / Armstrong Make of aluminium snap grid:- M/s Saint-Gobain Gyproc India Pvt Ltd / M/s USG Boral Building Products (India) Pvt Ltd / M/s PR Ceiling Products

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed. Make:- Colour Roof (India) Ltd / TATA Bluescope Steel Ltd / Dyna Roof / Bhushan Power & Steel Ltd / Prestar Infrastructure Projects Ltd.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed. Make:- Colour Roof (India) Ltd / TATA Bluescope Steel Ltd / Dyna Roof / Bhushan Power & Steel Ltd / Prestar Infrastructure Projects Ltd.

M&L machine cut kota stone flooring 20-25 mm (minimum) thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab and including rubbing and polishing and laid over 20 mm thick screed bed in CM 1:6 including dismantling complete all as specified and directed.

M&L for rubbing and polishing of machine cut kota stone slab flooring complete all as specified and directed.

M&L 18 to 20 mm thick marble tiles (makrana white) machine cut as in flooring, over 15 mm thick screed bed in CM 1:6 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

M&L 100 mm thick, PCC 1:2:4, type B-2 (using 40 mm graded crushed stone aggregate) as in sub base, floors, paths, plinth protection, hardstanding etc. finished even and fair without using extra cement complete all as specified and directed.

M&L 75 mm thick, PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub floor, sub base of floor, etc complete all as specified and directed.

S&F 1.5 mm thick and 38 mm wide Aluminium dividing strips as in floors inserted in position, confirm to design complete all as specified and directed.

M&L Bricks, sub class B,laid flat in drain old size brick bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 complete all as specified and directed

M&L Bricks, sub class B,laid flat in drain old size brick bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 but except bricks complete all as specified and directed

M&L Bricks, sub class B,laid on edge, in drain old size brick bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 complete all as specified and directed

M&L Bricks, sub class B,laid on edge, in drain old size brick bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 but except brickscomplete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 complete all as specified and directed. Make:- M/s Asian Granito India Ltd. / M/s Somany Ceramics Limited / M/s Varmora Granito Pvt Ltd / M/s OASIS Vitrified Pvt Ltd / M/s Sunshine Tiles Co (P) Ltd (Tiles) / Orient Bell Ltd / H & R Johnson India Ltd

M&L coloured glazed ceramic tiles 350x250x7 / 450 x 350 x 7 mm thick as in dado / skirting and vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick screed bed in CM 1:3 including roughening of surface complete all as specified and directed. Make :- M/s Asian Granito India Ltd. / M/s Somany Ceramics Limited / M/s Varmora Granito Pvt Ltd / M/s OASIS Vitrified Pvt Ltd / M/s Sunshine Tiles Co (P) Ltd (Tiles) /Orient Bell Ltd / H & R Johnson India Ltd

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in sub base, floors, paths, plinth protection, hardstanding etc. finished even and smooth without using extra cement complete all as specified and directed.

M&L for providing 75mm thick cement concrete 1:3:6 type C-2( using 40mm graded crushed stone aggregate) as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and fair without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

M&L for providing 100 mm thick cement concrete 1:3:6 type- C1 (using 20mm graded crushed stone) as in hardstanding/ path laid in alternate bays not exc. 4 Sqm each and finished even and smooth without using extra cement complete all as specified and directed.

M&L cement concrete chequered tiles 300 x 300 x 25 mm thick as in floors, set and jointed over and including 15 mm thick screed bed in CM 1:6 and pointed in grey cement and pigments to match the colour of tile complete all as specified and directed. Make : Lovely / Anjali / Ultra / Bansal / Nitco / Multiwyn

Taking down cement plaster on brick or concrete surfaces / ceiling, racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or stone masonry or on one side of lathing surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M & L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick work or stone masonry or on one side of lathing surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L for prepration of new plastered surfaces of wall applying two coats of oil emulsion distemper over a coat of alkali resistant cement primer over a thin layer of wall care putty to obtained smoothness of plastered surfaces complete all as specified and directed. Make of oil bound distemper :- Apcolite Premium Emulsion (Asian Paints ltd)/ Rangoli (Berger) / No. 1 Premium Acrylic Distemper(Shalimar) Make of primer/ wall care putty:- Asian Paints/ Berger / Shalimar Paints

M&L for prepration of new plastered surfaces of wall applying two coats of oil emulsion distemper over a coat of cement primer over a thin layer of wall care putty to obtained smoothness of plastered surfaces complete all as specified and directed. Make of oil bound distemper :- Apcolite Premium Emulsion (Asian Paints ltd)/ Rangoli (Berger) / No. 1 Premium Acrylic Distemper(Shalimar)

M & L for preparing newly plastered walls surfaces and applying two coats of cement base paint complete all as specified and directed. Make of cement base paint: Durocem Neo(Berger)/ Utsavcem (Asian Paints Ltd)/ Cemkote plus water proof cement paint(Shalimar)

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil emulsion distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed. Make of oil bound distemper :- Apcolite Premium Emulsion (Asian Paints ltd)/ Rangoli (Berger) / No. 1 Premium Acrylic Distemper(Shalimar) Make of primer/ wall care putty:- Asian Paints/ Berger / Shalimar Paints

M&L complete removal of existing treatment of old plastered or previously untreated walls surfaces and applying two coats of cement base paint over a thin layer of wall care putty complete all as specified and directed. Make of cement base paint: Durocem Neo(Berger)/ Utsavcem (Asian Paints Ltd)/ Cemkote plus water proof cement paint(Shalimar) Make of primer/ wall care putty:- Asian Paints/ Berger / Shalimar Paints

M&L for filling the gaps at the junction of roof sheet and vertical wall any thickness, any position and on height upto 10m from G.L using cement concrete type C1, 1:3:6 (using 20mm graded aggregate) and finish both side of wall by 15 mm rendering in cement mortar 1:6 and applying two coats of cement base paint to match with existing surface to match including necessary scaffolding complete all as specified and directed.

S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed. Make:- Asahi India Glass Ltd. / Saint Gobain / Modiguard / Triveni Float / IAG / Hindustan Pilkington

S & F Sheet glass 4.00 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed. Make:- Asahi India Glass Ltd. / Saint Gobain / Modiguard / Triveni Float / IAG / Hindustan Pilkington

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. Make of synthetic enamel paint:- Apcolite Premium Gloss Enamel (Asian) / Luxol High Gloss Enamel (Berger) / Superlac Premium High Glass Enamel (Shalimar Paints Ltd) Make of primer/ wall care putty:- Asian Paints/ Berger / Shalimar Paints

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc.) and fixed to wall / ceiling or laid in / on floor and including taking up/ down of old pipes complete all as specified and directed. Make - Tata / Jindal Steel / Surya Roshni Ltd. / Bhushan Power & Steel Ltd. / M/s APL Apollo Tubes Ltd

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc.) and fixed to wall / ceiling or laid in / on floor and including taking up/ down of old pipes complete all as specified and directed. Make - Tata / Jindal Steel / Surya Roshni Ltd. / Bhushan Power & Steel Ltd. / M/s APL Apollo Tubes Ltd

S&F rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank including dismantling of old tank complete all as specified and directed. Make of tank:- Sintex / Polycon / Polywell Make of ball valve:- Prayag Cat No. 152 or equivalent in Polytuf

M & L for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 450 mm bore pipe complete all as specified and directed.

S&F in replacement 450 mm bore Reinforced concrete pipes, class NP-2, laid in trenches and jointed with collars in cement and sand mortar 1:1, including demolition and breaking up unserviceable drain pipes (Salt glazed ware, AC or Reinforced concrete), set in cement mortar, complete all as specified and directed. Note :- Excavation & earth work shall be measured separately

S&F in repairs vitreous china wash hand basin white flat back of size not less than 550 x 400 mm with and including PVC waste pipe 32 mm bore, CP waste fitting and cutting for and pinning in ends of brackets etc, complete all as specified and directed. Make of wash hand basin:- Hindware, Cat No. - 10010 (Starwhite) or equivalent in Cera (Med Range) / M/s Jaquar & Company Pvt Ltd (Essco) Make of waste fitting - Prayag Cat No.- BEA-10 or equivalent in M/s Jaquar & Company Pvt Ltd (Essco) / Hindware (Less Italian Collection ) / Cera (Med Range) Make of PVC waste pipe - Prayag / M/s Pearl Precision Products Pvt Ltd / Polytuf

S & F in repair of 15 mm bore bib tap long body, chromium plated, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make:- Essco, Cat No. - SQT-511KN or equivalent in Hindware (Less Italian Collection) / Cera (Med Range) / Prayag (7000 & 8000 Series)

S&F in repairs pillar tap 15 mm bore,fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered “hot" or “cold” with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. Make:- M/s Jaquar & Company Pvt Ltd (Essco), Cat No. - SQT-507KN or equivalent in Hindware (Less Italian Collection) / Cera (Med Range) / Prayag (7000 & 8000 Series)

S&F in repairs sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 x 460mm bowl size 405 x 355 x 178 mm and including 32 mm waste pipe & coupling complete all as specified and directed. Make:- M/s Prabhat Sanitary Pvt Ltd (Brand IDOOS) / M/s Bluestar Sanitary Industries Pvt Ltd / M/s JMD International (Brand D-sons)

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Dismantling bricks (laid flat or on edge) in channels or brick tiles in floors, kerbs, aprons, etc. (each layer) Laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling Unframed timber scantlings 40 Sqcm and over in section and in any position in framed work complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including nainital or similar pattern in roof and wall covering omplete all as specified and directed.

Taking down copper / aluminium concealed point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc., removing materials to store for keeping in safe custody or for taking credit, cutting chasing as required and making good the disturbed surfaces including finishes to match with adjacent surfaces of walls, floors, etc. complete all as specified and as directed.

Taking down copper / aluminium concealed sub main wiring complete with all fixture and fittings including cutting chasing as required and making good the disturbed surfaces including finishes to match with adjacent surfaces of walls, floors, etc. complete all as specified and as directed.

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch and including cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. Make of cable:- Havells /MESCAB/ Polycab /Phinolex/RR Kabel Make of PVC Conduit:- Richa Cables / AKG Industries / Harsh Electro Systems / Panasonic (Anchor)

All as per Sl. item No. 96.00 above but for one 5 / 6 Amps socket outlet point on independent board.

All as per Sl. item No. 96.00 above but for one 16 Amps socket outlet point on independent board with 2.5 sqmm cable and 2.5 sqmm earth wire

M & L concealed sub main wiring with 2 runs of 2.5 sqmm main wire along with 1 run of 2.5 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length. Make of cable:- Havells / KEI / Polycab / RR Kabel Ltd. / HPL Make of PVC Conduit:- Richa Cables / AKG Industries / Harsh Electro Systems / Panasonic (Anchor)

M & L concealed sub main wiring with 2 runs of 4 sqmm main wire along with 1 run of 4 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length. Make of cable:- Havells / KEI / Polycab / RR Kabel Ltd. / HPL Make of PVC Conduit:- Richa Cables / AKG Industries / Harsh Electro Systems / Panasonic (Anchor)

M & L concealed sub main wiring with 2 runs of 6 sqmm main wire along with 1 run of 6 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length. Make of cable:- Havells / KEI / Polycab / RR Kabel Ltd. / HPL Make of PVC Conduit:- Richa Cables / AKG Industries / Harsh Electro Systems / Panasonic (Anchor)

S&F in repair switch piano, single pole, one way, 5 / 6 Amps, 240 volt complete all as specified and directed. Make :- Anchor / Havells/ C&S

S&F in repair switch socket combination 3 pin 15 Amp, flush type universal complete all as specified and directed. Make :- Havells / Anchor / C&S

S&F in repair switch socket combination 3 pin 5 Amp, flush type universal complete all as specified and directed. Make :- Havells / Anchor / C&S

S&F ceiling rose, 3 phase /PVC/ polycarbonate isolated body incluing taking down old unsv ones complete all as specified and directed. Make :- Anchor / Havells/ C&S

S&F lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings including taking down old unserviceable ones complete all as specified and as directed. Make :- Havells / Anchor / C&S

S&F in repairs LED battery backup inverter bulb of Lamp wattage: - 9 to 12 Watts, Battery: - Not less than 2200mAh or not less than 4 hrs backup,Efficeacy: - Not less than 110 Lm/Watt including taking down old unsv ones complete all as specified and directed. Make:- Crompton / Havells / Phillips

S & F in repair Surface and wall mounted LED batten 20 watt 4ft long with Aluminum extruded housing , high quality polycarbonate diffuser & integrated Electronic Driver with IP20, PF 0.95, Efficiency not less than 110 lm/W color temp 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V complete all as specified and directed. Make:- Crompton / Havells / Phillips

S & F in repair LED Bulk Head fitting 10 watt with Injection molded polycarbonate housing IP66, IK10, 3.5kV inbuilt surge protection, PF ≥0.95, total System Lumens not less than 1100 lm, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V. complete all as specified and as directed. ake:- Crompton / Havells / Phillips

S & F in repair LED Bldg Security Light 30 watt made up of pressure die cast aluminiun housing with highly efficient LEDs and PC cover with integrated lens with IP66, IK07, System Lumen Efficasy ≥120 Lm/W, having unique air vent technology which keeps temperature low, 5 kV Surge Voltage Protection,Operating Voltage range 140 V - 270 V and bracket suitable for street light made out of GI pipe light grade of 25 mm bore & 0.75 mtr length (minimum), bend to shape including 2 pairs of MS flat iron clamps made out of 40 x 5 mm MS flat, nuts, bolts & washers etc, & painting the bracket with two coat of aluminium paint over a coat of red oxide primer complete all as specified and as directed. ake:- Crompton / Havells/ Phillips

S&F MCB SPN 63 Amps 240V ,50 Hz ,breaking capacity 10 KA," C " series, including dismantling taking down unsvericeable ones complete all as specified and directed. Make :- L&T / ABB / Hager

S&F MCB SP,10KA, 230V, C-curve, 6-32 amps including dismantling taking down unsvericeable ones complete all as specified and directed. Make :- L&T / ABB / Hager

S&F MCB ,SPN DB, 8 ways double door,Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces including dismantling taking down unsvericeable ones complete all as specified and directed. Make :- L&T / Hager / ABB

M &L of Earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick, buried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connected using galvanised iron earth lead wire 4 Sq mm as earthing electrode by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe (medium grade) and other end connected to earthing test point as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C both ways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth up to a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 5 of MES Schedule Part-I complete including testing on completion. On testing after completion if the desired earth resistance is not obtained the earthing will be made again by the contractor at no additional cost and including dimantling complete all as specified and directed.

S&F in replacement earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4 mm dia galvanised iron or steel wire complete all as specified and directed.

S&F exhaust fan 300 mm sweep, heavy duty, metal body, 1400 RPM (minimum), AC single phase, 230 V, 50Hz along with louwer Shutter / bird guard, nuts, screws, bolts including electrical connection, writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole and making good the disturbed surface to match the existing surface complete all as specified and directed. Make :- Havells, Model - Turbo Force SF NEO or equivalent in or equivalent in Crompton /BAJAJ/Usha Note: Old unsv fans retrived from site deposited to the AGE EM Fan section and rate for the same is deemed to be included in the quotated rate.

M&L for cutting and making and enlarging existing hole for fixing of exhaust fan, nuts, bolts washer including plastering and make good the disturbed surface with the existing all as specified and directed.

S&F geyser of 2KW of capacity 25 Litres, 230V, 50Hz, vertical, wall mounted type, BEE 5 star rated, steel outer body and copper inner tank with, incoloy glass coated heating element, adjustable thermostat for temperature regulation, multifunctional safety valve with & including 3 core copper cable of 1 to 2 metre length with 3-pin plug of 16A capacity, fixing arrangement such as. bracket, nuts, bolts washers etc. complete all as specified and directed. Make:- Havells Manza slim Cat Part No.- GHWBMDSWH 025 or equivalent in V-Guard / Bajaj / Usha / Crompton Greaves / Jaquar & Company Pvt. Ltd.

SHRI N.DAS

M/S G S ASSOCIATES

A K ENTERPRISES

Janata Enterprises

KARMIBRINDA

MS ESSCON

D K SARKAR