REPAIR AND REPLACEMENT TO ROOF TREATMENT, PERIODICAL SERVICES, JOINERY WORK, PLUMBING, SANITARY WORK AND OTHER CONNECTED ITEMS AND MISC B/R ITMES AT PCC WARD, BOYS HOSTEL, NEW OPD COMPLEX AT ZONE B BHDC UNDER GE (EAST) DELHI CANTT-10

Amount

S&F in repair 10 mm thick Toughened glass as in partition/ fixed window including diamond edging all sided , eatching , lining and momnograme area nexc 0.50 Sqm each by sand blasting , including CP " L" or " U" heavy duty clamps suitable for fixing of glass , min 4 Nos per Sqm all as specified and directed.

S&F in repair 10 mm thick toughened frosted glass door shutters of size area exc 1.50 Sqm but not exc 3 Sqm , including necessary floor spring hydraulically regulated , otherside fixed on pivot. CP fittings and fixtures , CP handles , CP locking arrangement , necessary cutting & holes moulding and fixed in complete as specified and directed

Dismantling floor hearth or wall tiling including cement mortar bedding and rubbish off the premises complete all as specified and as directed.

M&L for Vitrified tiles 8-9 mm thick (square/rectengular) polished, size of each tiles is 800x800mm as in floors, over and including 15 mm thick screed bed in CM 1:4 and joint shall be kept as 3mm filled with epoxy to attain the best result 3mm thick tile spacers to be used, Masking tape shall be put before putting the eposy grout & the grout shall be throughly cleaned immediately. complete all as specified and directed.

M&L Vitrified tiles 8-9mm thick (square/ rectangular) polished, area of each tiles not exc 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed.

All as per item No. 5 here-in-before but on vertical surfaces over and including 10 mm thick plaster in cement mortar 1:4 complete all as specified and as directed.

M&L for glazed coloured ceramic tiles in dado/vertical surface (450mm x600mm x 7-8 mm) thick fixed with chemical adhesive Fevi Mate of euivalent and joint shall be kept as 3mm filled with epoxy to attain the best result 3mm thick tile spacers to be used, Masking tape shall be put before putting the eposy grout & the grout shall be throughly cleaned immediately complete all as specified and directed.

M&L for glazed coloured ceramic tiles in dado/vertical surface (450mmx 300mm x 7mm) thick set and jointed in neat cement slurry and pointed in coloured cement to match over including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed

M&L for 900 mm x 300 mm x 12 mm thick glazed exterior tiles fix with neat cement slury over and including 20mm thick screeding in cement mortar 1:4 and and 100 mm thick PCC 1:4:8 type D2 & pointing with epoxy mortar all as specified and directed.

M & L for Coloured Glazed ceramic tiles in vertifical surface 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in colour cement to match over and including 10 mm thick rendering in CM 1:4 complete all as specified and as directed.

M & L for Non-skid Coloured Ceramic tiles 7 to 8 mm thick (Square/rectangular) area of tile exc 0.11 Sqm but not exceeding 0.18 Sqm in floors, set and jointed in neat cement to match the shade over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

Taking down chowkhat or frame without taking off shutters of any description exc 1.5 sqm and n-exc 4 sqm each complete all as specified and directed.

Taking down chowkhat or frame without taking off shutters of any description not exc. 1.5 sqm complete all as specified and directed.

Taking down Shutters of any exc 1 Sqm but n exc 2.0 Sqm complete all as specified and directed.

S & F Pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

S&F Pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

S&F IInd Class HW 35 mm tkick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated

S&F IInd Class HW 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

S&F 35mm thick pre-laminated designer factory made flush shutter of laminate or equivaqlent including necessary hardware and fittings all as specified and directed

S&F 300mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F 150mm long Mild steel pressed handles, oval type, stove enamelled black bolt complete all as specified and directed.

S&F 200mm Mild steel barrel tower bolts, stove enamelled black, with bright boltand fixed complete all as specified and directed.

S&F aluminium powder coated window and ventilator shutter ,side hung type without sash bar, aluminium section weighting 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws , anodised aluminium fitting such as peg stays 150mm long (1 No), hinges tyjpe B-21 100mm long (2 Nos) suitable handle (1 No) complete all as specified.

S & F Aluminium powder coated door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors, windows,ventilators all complete as per architectural drawings and the directions of Engineer-in-Charge.

S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete

S & F 12mm mm thick PVC moulded solid board both side prelaminated for door and partition complete all as specified and as directed.

S&Fin repair Vinyl Floor seamless antistatic conductive ESD, anti fungal vinyl flooring system, 2 mm thick , with perfectly curved flush covings and copper strips for earthing, all joints welded properly including wall scatting. Flooring in operation theater room will be seamless with perfectly curved flash covings, resistance to mechanical stress and dynamic loads and having ESD/EMI (Conductive) protection characteristics, 2mm thick, washable vinyl. The condictive carbon coated PVC pellets create the permanent static conductive properties. It complies with EN 649. Before laying the Flooring inside the Operation theater a copper strip of width of 25 mm and thickness of 0.05mm is placed in such a way the each flooring tiles get cunnected to earthing complete all as specified and as directed. ( Make - MHS, Gerflor, Tarkett or Equivalent)

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying & fixing in opening as per specification.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site all specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded

S&F 150 mm Aluminium handles, cast type anodised complete all as specified and directed.

S&F 100mm butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21 complete all as specified.

S&F 200mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified.

S&F Galvanised mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staple complete all as specified and directed.

S&F in repair Galvanised mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staple complete all as specified and directed.

Hacking out old broken glass (any thickness) from metal frame/aluminium frames including punching or drilling out old galzing pins complete all as specified & directed.

S & F 4.0mm thick ordinary glass and glazing with oil putty in square n exc 0.5 Sqm in each pane or rubber beading /putty as required complete all as specified & directed.

S & F 4.0mm thick Frosted glass and glazing with oil putty in square n exc 0.5 Sqm in each pane or rubber beading/putty as required complete all as specified & directed.

S & F in repair Stainless steel glass door handle 600mm long with screw complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc

M&L rendering 15mm thick in Cement Mortar 1:4 on fair faces of brick or concrete, external surfaces of walls finished and even & fair without using extra cement complete all as specifed & as directed.

M&L rendering 15mm thick in Cement Mortar 1:6 on other than fair faces of brick surfaces of walls finished the surface even & fair without using extra cement complete all as specifed & as directed.

M&L 10 mm thick plastering in Cement Mortar 1:3 finished even & fair w/o using extra cement on ceilings complete all as specifed & as directed.

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 white cement: 1/2 coarse sand : 2 white marble stone chipping 10mm nominal size with colour compound) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and as directed. (Note: Payment for providing grooves shall be made separately).

M&L forming groove of uniform size 15 mm wide and 15 mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete all as specified and directed.

M&L for preparing the newly plastered wall surface, applying 2mm thick wall care putty followed by two coat of oil bound distemper over one coat of interior primer complete all as specified and directed.

All same as per srl item No 47 but on ceiling over 1mm thick, wall care putty.

M & L for preparing the newly plastered wall surface and applying two coat of cement base pant over one coat of cement primer complete all as specified and directed.

Dismantling of Stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floor, aprons etc.

M&L for 20 mm thick Granite work in platforms, partitions and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite & half curving the edges of granite over and including 20 mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L for 60 mm thick Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006, M-40 Grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete including dismantling of existing paver tile block all as specified and directed.

SF in repair Kerb stone of 300x300x100mm thick precast plain cement concrete type B0 , 1:2:4, using 12.5mm graded crushed stone aggregate incl earth work for laying kerb stones.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

M & L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed alusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F in replacement Aluminium extruded section body door closer, hydraulically regulated, design No 2, universal type, suitable for door shutter 701 mm to 850 mm in width and of weight 36 to 60 Kg each complete all as specified and as directed.

S & F in repair Double action floor spring, hydraulically regulated, made out of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel, heavy duty and fixed complete for glass/aluminium door complete all as specified and as directed.

S & F in repair brass mortice lock 65 mm 4 lever vertical type with duplicate key and handle set complete all as specified and as directed.

S & F in repair brass mortice lock 100 mm, 4 lever, vertical type, with duplicate key complete all as specified and as directed.

S & F in repair 150mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified.

S & F in repair 150 mm Aluminium handles, cast type anodised complete all as specified and directed.

S & F in repair stainless steel butt hinges medium weight 100 mm long fixed to frame as required complete all as specified.

S & F in repair aluminium alloy,anodised,sliding door bolt plate type 250 mm long and fixing clips of sheet ,cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified .

S&F in repair 20 mm dia decorative drapary curtain road with finials & brackets & internal funnels. complete all as specified.

S & F in repair of polished Bottom lock of glass door complete al as specified and directed.

S & F in repair brass drawer lock, 65 mm, 2 lever, with duplicate key complete all as specified and as directed.

S & F in repair Stainless steel drawer channel, 300mm length complete all as specified and as directed.

S & F in repair Stainless steel drawer channel, 450mm length complete all as specified and as directed.

S & F in repair Brass drawer handles, projection drop (50mm to 65mm) on screwed platecomplete all as specified and as directed.

S & F in repair Vitreous china wash down water closet pan (pedestal pattern), floor mounted with inbuilt P trap in white colour, including connection to trap and to flushing pipe including provn of cement concret beading complete all as specified and directed.

S&F in repair vitreous china Squatting pan "Orissa pattern" size 580x440xmm white, with integral foot rest incl p trap and necessary connection to trap and flushing pipe etc complete all as specified and directed.

S&F in repair Table top wash basin, white, flat back size 525x415x140mm of make -Jaquar cat part No JDS-WHM-25907N or equivalent excluding tap, chain, plug but including brackets, waste fitting 32mm dia ,brass chromimium plated for glazed ware sink, basin,with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified.

S&F in repair white Wash Basin of size 560 x 415 x 820 mm including braket complete all as specified and directed. Make : Prayag Cat No : 4602 or equivalent in Cera/ Parryware.

S & F in repair plastic water closet seat cover white, closed pattern with flat bottom and mild steel chromium plated hinging device complete all as directed and as specified.

S&F in repair Vitreous China half stall urinals, (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. incl of fixing supply pipe to flushing cistern, trap and waste pipe)

S&F in repair white, vitreous china, battery based, infrared sensor operated urinal of approx size 710x 485x310mm having pre & post flushing with water, including fixing to walls complete all as specified & as directed. Make : Jaquar Cat No URS-WHT-13255 & SNR-CHR-51097 or Equivalent model of GROHE/KEROVIT (Kajaria)

S&F in repair Urinal Spreader of CP White colour fixing to 15 mm bore pipe.

S & F in repair 15mm bore Pillar cock Swan neck spoout and aertor for WHB complete all as specified & directed. Make : Cera Cat No.: F1099104 or equivalent in Marc/ Jaquar/ Kohler.

S & F in repair of PVC low level flushing cistern 10 ltrs capacity incl PVC float valves, PVC connection and out let pipes complete.

S & F in repair 15 mm Quarter turn basin mixer without Popup waste system with 357mm Long braded hoses of make Jaquar cat part No-ALI-85001 or equvalent in Marc/ Kohler for fixing hot & cold waterscrewed down for iron pipe and fixed all as specified and as directed.

S & F in repair of repair fancy type stop valve make of jaquar or equivalent in Marc/ Kohler copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions chromium plated of size 15 mm. all as specified

S & F in repair of Quarter turn Bib tap make of jaquar cat part No ALI-85037 with wall flange or equvalent in Marc/ Kohler for iron pipe of size 15mm bore chromium plated. all as specified

S & F in repair of Gun metal globe of gate valve with iron wheel head, screwed both ends of size 15mm

S & F in repair of Gun metal globe of gate valve with iron wheel head, screwed both ends of size 20mm

S & F in repair 2 in 1 Angle Valve 15 mm CP fancy pattern type cast copper alloy make of jaquar or equivalent in Marc/ Kohler screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S & F in repair Angle Valve 15 mm CP fancy type cast copper alloy make of jaquar or equivalent in Marc/ Kohler screwed for iron pipe or forbrass ferrule and fixed all as specified

S & F in repair CP hand spray (health facucet with 1.5 M long easy flex tube in chrome finish and wall hook) make of jaquar or equivalent in Marc/ Kohler complete all as specified and directed.

S & F in repair of chromium plated jet for WC with 1.00 M long pipe including necessary fittings complete all as specified and directed.

Dismantling water tanks exc 250 & n exc 500 ltr capacity and removing to store

S&F 500 ltr Rotational moulded Polyethylene water storag tank (Cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed.

S&F in repair 20mm bore dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwedfor iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./ 25mm-455gms/ 40mm - 690 gms)

S&F in repair Corrugated Waste Pipe 32 mm dia for WHB//Sinkcomplete all as specified and directed.Make : Prayag Cat No 327.

S&F in repair Waste coupling 32mm bore dia of PTMT half threaded for WHB/Sink complete all as specified and directed.

S & F in repair of Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges aluminium anodized, fixed with rawl plugs. all as specified. Make: Jaquar/ Marc/ Kohler.

S & F in repair 600mm Long PVC connection suitable for 15mm bore pipes complete all as specified and as directed.

Disconnecting existing tanks, setting aside for repairs including cleaning and removing all scale and dirt, etc from tanks and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

S&F in repair Full Glass Shelf 450 mm (with brass brackets) complete all as specified and directed. Make : Prayag Cat No : BEA-55 or equivalent in as approved by GE.

S&F in repair corner Glass Shelf 300mm (with brass brackets) complete all as specified and directed. Make : Prayag Cat No : BEA-44 or equivalent in as approved by GE.

S&F in repair CP Soap Dish including chromium plated brass screws and plastic cleats complete all as specified and directed. Make : Prayag Cat No : BA-05 or equivalent in as approved by GE.

Dismantling of Brick tiles or terracing tiles, single layer on roofs complete all as specified and directed.

Demolition Mud in roofs, any thickness, including plastering,PCC pedding including sweeping clean and washing down with water to remove dust, etc and disposal of all bldg Materials to out side MOD land as per NGT guide line complete all as specified & directed.

Digging out plant roots from roof/wall, removing unserviceable material and cleaning site and making good distrubed portion in CM 1:4 or cement concrete 1:2:4 type B1 as required complete all as specified and directed.

Demolition of PCC of any description and in any position and disposal of all debries to out side MOD land as per NGT guide line complete all as specified and directed..

M&L for Cutting grooves in brick wall, 75 mm wide and 65mm deep and shaping horizontal face of grove with cement mortar 1:3 complete all as specified and directed.

M&L for providing plain cement concrete, type B-1, 1:2:4 (using 12.5 mm graded stone agg) as in levelling course , roof kerbs, padding, Gola, rounded or chamfered on edges complete all as specified and directed.

M&L for 20 mm thick rendering on concrete surface of roof with cement mortar 1:4 finished even and fair including mixing of water proofing compound as per manufacturer's instructions complete all as specified and directed. (Note : Water proofing compound shall be measured and paid separately)

Supply only water proofing compound.

M&L for roof treatment with polymeric membrance (APP based) with non woven polyster mat as reinforcement with following:- (a) M&L for cleaning the new plastered surface and providing & laying a coat of cold applied bitumen 85/25 based primer on entire surface @ 0.40 Ltr/Sqm on dry and clean surface. (b) M&L for providing & laying APP based polymeric membrane of 3 mm thickness of weight of 4.0 Kg/Sqm with non woven polyster fibre as reinforcement on primed surface by torch application with 15 cm end over laps & 10 cm side over laps (overlaps to be thermo fused by flame) and applying one coat of hot blown bitumen 85/25 @ 0.70 Kg/Sqm all as directed. Make : STP & IWL.

S & F fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 10 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid over and including 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

M&L for Two coat of Aluminium paint over a coat of primer on APP membrance of any description, over 10cm in width or girth,not otherwise described complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed.

M&L for One coats of synthetic enamel paint on old wooden Surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of Red oxide primer on new Steel Surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed.

M&L for One coats of synthetic enamel paint on old Steel Surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed.

M & L for complete removal of existing treatment from old decorated wall surface by scrapping by electrically operated grinder machine/electric regmal machine and applying one coat of wall care putty then scrubbing by sand paper to prepare a even surface and applying interior primer followed by applying two coats of OBD of any colour washing down with water complete all as directed. (Asian Paints,Berger)

M & L for preparing the old surface of ceiling by washing down and rubbing and removing all loose layers of old treatment, efflorescence , soot and moss by wire brush and filling all nail holes and patches with cement wall putty and applying one or more coat of oil bound distemper on patches to bring the whole surface at par and applying one coat of oil bound distemper on ceiling complete all as specified and directed.

M & L for complete removal of existing treatment from old decorated wall surface by scrapping by electrically operated grinder machine/electric regmal machine and applying one coat of cement primer followed by two coats of cement based paint on old plastered surfaces complete all as specified and as directed (Note: Quoted rates shall deemed to be included painting at any height including scaffolding work, as required. )

Taking up or down 25mm bore steel tubing and connections, including cleaning for refixing or removal to store

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store

Refixing old 25mm bore steel tubing and connections in new or old position (Walls, ceiling, floors, etc.complete.

Refixing old 20 mm bore steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete.

S&F 25 mm dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc

S& 20 mm dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc

S&F 16 mm dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc

S&F in repair PEG Set 6 (Zinc) complete all as specified and directed.

S&F in replacement 125mm dia chromium plated gratings over nahani / floor traps including embedded the same in white cement to match complete all as specified and directed.

Dismantling of CI pipes & fitting of any description & position up to 100 mm dia complete all as specified & directed.

S&F PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints to walls

S&F PVC (SWR) 75 mm bore pipe single socketed, in any length with rubber ring jointes , laid in trenches or in floor complete all as specified and directed.

S&F PVC (SWR) 110 bore pipe single socketed, in any length with rubber ring jointes , laid in trenches or in floor complete all as specified and directed.

S&F PVC (SWR) 110 bore pipe single socketed, in any length with rubber ring joints to wall complete all as specified and directed.

S&F PVC (SWR) floor trap 75 mm dia, plain with grating including jointing with solvent cement complete

S & F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

S&F 75mm bore PVC (SWR) vent cowl

S & F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays for 75 mm bore pipe, including bolts and nuts and securing ends of stays to wall or roof .

S & F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays for 100mm bore pipe, including bolts and nuts and securing ends of stays to wall or roof .

S&F 75mm PVC (SWR) junction single,(Single T) equal or unequal with acces door.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified and directed.

Demolition of brick work built in cement mortar complete all as specified and directed

M & L for brick work with sub-class B brick straight or curved on plan built in cement mortar 1 : 6 complete all as specified and directed

Demolation of PCC of any description and in any position not otherwise specifically provided for drain etc.

M&L 75 mm thick PCC 1:3:6, type C1, using (20mm graded aggregate) as in Plinth protection and finished the surface fair & even without using extra cement, laid in panel , including filling the joints with sand mixed with bitumen in 1:1 ration complete all as specified and directed.

M&L cement concrete 1:2:4 type B0 (using 12.5mm g raded aggregate) as in copings apex stones, bed plates kerbstone in benching all as specified and as directed.

M & L PCC type D2 1:4:8 Using 40mm graded stone aggregate as in sub base complete all as specified and as directed

M/L PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as in surfaces channels,drains etc.

S& F in repair 75mm thick factory made SFRC manhole/ drain covers of approved shape & size complete all as specified and as directed. Make : Polycrete or equivalent as approved by GE.

M&L for guniting of spalled/corroded reinforced cement concrete surface,i.e column, beam, slab, chajja, comprising of chipping of spalled and loose concrete, cleaning rust form reinforcement by sand blasting, scrubbing down concrete surface with wire brushes, cleaning with water; allowed to dry and applying a layer antirust chemical of fosroc or equivalent on all exposed reinforcment followed by a layer of bonding coat of approved epoxy adhesive on complete exposed surfaces of concrete to be gunited; applying two layers of guniting over steel welded wire mesh having 5mm dia of wire and aparture 50mm, total thickness of gunite not exceeding 60mm thick (average thickness) in cement mortar 1:2 using OPC 43 grade weight cement duly mixed with polycrete admixture @2%by weight of cement or as per manufacturer's instruction and finally applying cement plaster over guinite surface of required thickness to give even uniform and smooth finish conforming to proper geometrics in cement mortar 1:3 to match with the existing suface as in sides and soffits etc of slabs, chajjas,fins. fascias, parapets,lintels,columns& beams etc with and including necessary scaffolding, shuttering, chases to brick work or RCC members etc, complete all as specifed and all as directed. Note - GI wire shall be insert into RCC member by doing hole then inject HILTIHIT RE 500 into the hole before guniting.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets

S & F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

M&L for 6mm th Non asbestos fibre cement building boards fixed to GI frame work in ceiling surface.

M&L for One coats of synthetic enamel paint on old Concrete Surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed.

M/s Shubh Enterprises

friends associeates

M/S Rohit Enterprises

Gaurav India Corporations

M/s Sree Baba Traders

MAA SANTOSHI ENTERPRISES

S GOURAV PRAKASH ENTERPRISES

R R Associates