PETTY REPAIRS LIKE TILING, PLASTERING, PLUMBING, SANITARY WORKS, CHAJJA REPAIRS, CONNECTED MISC B/R WORKS AND PERIODICAL SERVICES AND DESLUDGING OF SEPTIC TANK, CLEANING OF SEWAGE LINE, MANHOLE, REPAIR/REPLACEMENT OF SEWAGE LINE, MH COVER AND ALLIED

Amount

Attending day to day complaints to carry out petty repairs related to water supply & plumbing work such as leakage of bib cock / pillar cock / stop cock angle valve, wall mixer, shower rose, health faucet/Jet spray, including removal of air lock/blockage of water in GI tubing of any description changing the washers, clearing of air lock in the pipe, leakage of low level or high level flushing cistern by adjusting the float valve including removal and replacement of rubber washer in PVC siphons, adjusting the float valve of over head tanks, leakage of PVC bends/galvanised iron pipes etc., All T&P such as die set, washers of all size etc including necessary form work and scaffolding upto second floor, safety measures to make functional and leak proof, all petty materials like taflon tape, M-seal, screws, nails, cap etc. are deemed to be included in the unit rate quoted by the contractor on all working days from 0900 hrs to 1700 hours complete all as directed.

Attending day to day complaints to carry out petty repairs related to joinery work such as repairs to cupboards, kitchen shelves, pelmet boxes, easing of doors and windows etc as ordered / required on all working days (except Sunday & gazetted holiday) from 0900 hrs to 1700 hours complete all as specified & directed.

Note for Item No. 1 to 2:- (i) Contractor or his supervisor/site Engineer will report daily at 0900 hrs at complaint cell for collection of complaints from the concerned JE in-charge, in case after checking & attending the defects, if it is not possible to rectify the defects within 08 hrs, the facts shall be brought to the notice of JE than after to Engineer in charge by the contractor/ his rep immediately. If Engineer-in-charge is satisfied with contractor's view, no recovery will be made on this account. However complaints related to sewage line blockage /pipe replacement etc whatever is applicable shall be attended on same day whether it is "Sunday" or "Gazetted Holidays" and nothing extra shall be payable to contractor on this account. (ii) Contractor or his supervisor / site engineer will report daily at 0900 hrs at complaint cell for noting of day to day complaints in complaints register, issue of complaints slip to tradesmen and enter after completion in complaint register as instructed by JE,s. In case of absense of contractor rep for noting complaints, a penalty of Rs 500.00 per day will be deducted from the contractor bill. (iii) The complaint shall be attended & defects shall be rectified within 08 hrs i.e from 0900 hrs to 1700 hrs excluding Sunday & gazetted holiday, commencing from date and time of notifying the complaint slip failing which a Penalty @ Rs.500/- Per complaint per day (08 hrs) shall be levied upon / imposed on the contractor and necessary recovery shall be made from his dues on this account. The contractor at the begining of contract will provide printed 30 x complaints slip book as per proforma let wiht 400 leaf each booklet. (iv) The above all aspect shall be deemed to be included in the quoted rate of the respective item.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises etc complete all as specified and directed.

M&L Screed bed or bedding layer of mortar 20 mm thick for laying floor tiles in cement mortar 1:6 finished even and rough.

M&L 20mm thick Granite( of any size) work in cooking plate form and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade .

M&L for glazed ceramic colour designer concept glazed ceramic tiles 450x350x7mm size as in walls set and jointed in neat cement slurry over and including 10mm thick backing coat in cement mortar (1:4) and pointed in coloured cement to match for work on vertical surface such as skirting dado etc complete all as specified & as directed by Engr-in-Charge.

M&L glazed coloured ceramic tiles 300x200x 6 to 7mm thick as in vertical surface such as skirting, dado, etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles incl 10mm thick plastering in CM 1:3 complete all as specified

M & L Non skid coloured ceramic tiles 7 to 8 mm thick matt finish(square/ rectangular) area of ech tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with tile incl screedd bed 15 mm thick in CM (1:6) complete all as directed and specified.

Demolition of cement concrete in ground floor and pavings nexc 15cm thickness (below or above ground level).

M&L 75 mm thick PCC 1:3:6 type C2 using 40mm graded stone aggeragate as in plinth protection and paving finishing surface even and smooth without using extra cement

M&L for repairing of 40mm thick flooring in patches with PCC (1:2:4) 20mm graded stone agg. & finished even & smooth w/o using extra cement. . The rates include demolition of existing concrete complete all as specified and directed by Engr-in-Charge.

Blank

Taking down cement plaster from walls of any description all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight of curved on plan exc 6M mean radius built in CM 1:6 complete incl demolition of brick work built in cement mortar all as specified & directed by Engr-in-charge.

M/L 15 mm thick cement plaster in CM (1:6) including finished even and smooth (without using extra lime or cement).

M&L 10mm thick cement plaster in CM 1:6 on brick work or concrete surfaces rendering is to be even & smooth without using extra cement on internal walls

M&L for applying two coats of distemper (OBD) including Preparation to the new surfaces of wall, all as specified and as directed

M&L for Preparation of newly plastered surfaces and applying two coats of cement base paint on walls incl priming surfaces with alkali resistant priming paint etc complete all as specified and directed.

Dismantling of old Ceiling boards (Fibre,pulp,insulation,etc) or insulation boards /slabs blankets,including cover fillets and frame work.

S&F of Armstrong Board 12mm thick in ceiling all complete as per manufacturer’s instructions .

S&F Anodized aluminium snap grid of size 605mmx605mm (Powder coated) frame work for false ceiling, including 4mm dia GI wire for hanging all as specified in SSR and as directed by Eng-in-charge.

Taking down door chowkats or frames not exceeding 1.5 sqm with shutters (without taking off shutters from the frame) of any description

All as per item No 23 above but exceeding 1.5 sqm but not exceeding 4 sqm

Taking down shutters of any description exc 1sqm and n.exc 2sqm each

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue, pinned at joints complete all as specified and directed.

S& F flush door 30mm thick membrane doors decorative finish on one side duly finished and polished and other side all as per manufacturers directions as per tint / colour including necessary teak wood lippings of necessary all as directed by Engr - In Charge. (Note; manufacture MAXON,)

S&F 30 mm thick flush shutter, soild core construction, with particle board core and plywood face panels, (membrane doors of any colour any Code/model name of Maxon doors only)all specified and directed.

S&F second class hard wood glazed and skeleton shutter for doors open rebated and prepared to receive glass, gauge etc divided into squares with plain chamfered or mitered and rebated sash bars any number, edges or framing, plain chamfered or rounded fitted with beads for securing glass gauge size of members of shutters as specified in SSR part I factory made shutters of 35 mm thick all as specified and as directed by Engineer-in-Charge.

S&F Solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with 19mmx19mm MS square tube. EPDM rubber gasket weather seal to be provided throughout the frame. The profile shall be mitre cut at two corners and joined by inserting 2mm of 150mm long brackets of 15x15mm MS square tube inside the 19mmx19mm MS square tube and suitably screwed. The door frame shall be fixed to the wall using 65x100mm long cdium plated screws through the frame by using PVC fasterness. A minimum of 06 Nos screws to be provided for each frame supplying & fixing in opening as per specified and directed Note : Cuting holes, providing cement concrete for holdfast finishing all disturbed surfaces (CM 1:4) around door frame etc are deamed in this item

S&F factory made Moulded solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for Top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lack rail & bottom rail on either side & as far insert for top rail & bottom rail ; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beating and joined together with solvent cement supplied and fixing in the frame at site including all fixture & fittings etc all as specified and as directed.

M&L preparing new or previously untreated wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

S&F 100 mm Stainless steel hinges of any colour all as specified & directed by Engr-in-chargeas fixed in repairs.

S&F for aluminium handle 150mm cast type anodised.

S&F for aluminium anodised, barrel tower bolt 200mm of extruded section.

S&F aluminium alloy anodised, sliding door bolt 250 mm long with hasp, staple (bolt type) and fixing clips of sheets , cast or extracted section and fixing bolt and sliding bolts of extracted section.

S&F in repair 100 mm Stainless steel hinges of any colour all as specified & directed by Engr-in-charge

S&F in repair Stainless steel barrel tower bolt 200mm of extruded section

S&F in repair Stainless steel handle 150mm all as specified and directed by the engineer -in -charge.

S&F in repair Stainless steel handle 100mm all as specified and directed by the engineer -in -charge.

S&F in repair 150mm floor door stopper of Stainless steel body ,fixed in floor all as specified and directed by Engr-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone concrete glazed with oil putty or fixed with beeds.

S&F sheet glass ordinary quality 4mm thick and glazing with oil putty in square n.exc 0.50 Sqm in each pane all as directed by Engineer-in-Charge

All as item 43 above but figured glass pin head type.

S&F sheet glass ordinary quality 4.80 mm thick as in doors, showcase alum frame work & similar work with or without glass roller area exc 0.50 Sqm including neoprime gasket all as directed by Engineer-in-Charge

Easing of aluminium doors including taking out door shutters and changing of certain parts if required like pilots,hinges,rubber beadings etc as required and re-fixing in same position and size of doors n.exc 4 sqm each.

All as per item no 46 but for windows.

S&F powder coated aluminium annodised frame for door/window/ventilator with one or more rebates including jointing cleats for fixing etc complete all as specified and directed.

S&F aluminium annodised door/Windows/ventiliator shutters aluminium section weighing 0.55kg/m including necessary joining, fixed type, cleats, glazing clips, rubber neoprene packing, handles 02 nos in each door, hinges, anodised alumnium snap beading, screw etc, complete all as spd.

S & F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width or aperture 1.40 mm all as specified and directed.

S& F Stainless steel wire cloth. 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples .

S&F in repairs ISI marked hydraulically regulated door closer designation no.03 universal type,suitable for door shutters of 851 to 1000 mm in width and weight betwwen 61 to 80 kg width upto 1.50 mm mtr and weight between 61 to 80 kg complete all as specified and directed by Engr-in-Charge..

Easing of wooden window shutters/CB shutters (One unit shall comprising of one window/ CB/ Showcase/ irrespective of number of leaves) for properly closing/ opening tightening of hinges or changing the position of hinges adjustment of tower bolts sliding bolt etc complete all as specified & directed by Engr-in-charge.

All as per srl item No 53 above but door shutter.

M&L for replacement of wooden glazing beading of 2nd class hard wood straight (any size) finished wrought for glazing or gauged joinery for fixing wire gauge/ securing glass pane complete all as specified and directed by Engr-in-Charge.

S&F in repair MS 180mm( Powder coated), ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engr-in-Charge.

M&L for Running welding in repairs on metal to be welded of thickness exc. 6mm but n.exc. 9mm including preparation of surface, etc complete all as specified and directed by Engr-in-charge.

Taking up or down 15mm bore steel tubing and connections including cleaning for refixing or removal to store.

Taking up or down 20mm bore steel tubing and connections including cleaning for refixing or removal to store.

S&F CPVC pipes 20 mm SDR 11 & Plain VPVC SDR 11 on walls, ceiling orf laying including fitting in floors all as specified and as directed by Engr in Charge.

S&F in CPVC pipes 25 mm SDR 11 & Plain VPVC SDR 11 on walls, ceiling orf laying including fitting in floors all as specified and as directed by Engr in Charge.

Taking down and re-fixing of old steel tubing connection in new or old position (wall etc) including cleaning for re-fixing bore of pipe 15mm/20mm dia complete all as specified and directed by Engr-in-Charge. Note: - New GI fittings such as elbow, socket, Tee, Union, Nipple are included in rates required for re-fixing of pipe.

Demolition and breaking up drain pipes ( salt glazed ware , AC, PVC or reinforced conc ) set in cement mortar of internal dia 75-100mm incl any earth work and demolition of PCC, complete all as specified.

S&F in repairs PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall (110 mm bore) including flat iron claim for proper fixing complete all as specified & directed by Engr-in-charge.

S&F in repair PVC(SWR) bends 110mm dia complete all as specified & directed by Engr-in-Charge.

S&F in repairs PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall (75 mm bore) including flat iron claim for proper fixing complete all as specified & directed by Engr-in-charge.

S&F in repair PVC(SWR) bends 75mm dia complete all as specified & directed by Engr-in-Charge.

M&L for 75mm dia of outlet PVC Nahani trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engr-in-Charge.

S&F in repairs vitreous China squatting pan 'orrisa' pattern white colour of size 580x440mm with integral foot rests including p' trap and provision of cement concrete complete all as specified & directed by Engr-in-charge .Makle Cera or equivalent as approved by GE.

S&F in repair wash down water closet (pedestal pattern) of any colour including fixing of bolts complete all as specified and directed by Engr-in-Charge.Make - Cera or equivalent as approved by GE.

S&F in repairs plastic EWC seat cover of white colour pedestal pan , closed pattern withg flat bottom & cover including MS chromium plated ,alum hinging devices complete all as specified and directed by Engr-in-Charge.Make Cera or equivalent as approved by GE.

S&F in repairs 10ltr capacity PVC valve less syphonic action type flushing cistern low level white with inlet ball valve ,float & handle including brackets complete all as specified and directed by Engr-in-Charge(.Make- Cera or equivalent as approved by GE.)

S&F in repair PVC syphon kit for low level flushing cistern (Make cera)or equivalent as approved by GE.

M&L in replacement of brass face spindle of existing 15mm dia bore bib cock, stop cock, angle valve, C P Pillar cock, Wash basin mixture and valve mixture of any description fixed in repairs complete all as specified and directed by Engr-in-Charge.(Suitable for make Jagur,Cera,Sieko and Zollota etc)or equivalent as approved by GE.

S&F in repair for vitreous china wash basin white flat back size 550x400 including cutting for and pinning in ends of brackets including of fixing of 32mm low density polylethyne pipes (LDPE)of pressure rating 6kg/cm2,coupling, PVC connection with 15 mm PTMT cheknuts, brackets all complete as directed by Engr in Charge.

S&F in repairs CP Towel rail including fiitings of neccessary screws etc complete all as specified and directed by the Engr-in-Charge.Make : Cera/Jaguar/Ess Ess

S&F in repairs CP health fauccet of including neccessary holding arrangements with screws etc all as specified and directed by the Engineer -in -charge.

S&F in repair PVC Cabinet mirror (size 500x400mm) all as specified directed by engr in charge. Make: Prayag Cat No.556 or equivalent as approved by GE.

S&Fin repairs Basin mixer 15 mm dia Fancy type

S&F in repairs swan neck Pillar cock CP 15 mm dia model

S&F in repair Waste coupling of CP ( half or full threaded) of 40 mm dia.

S&F as in repair 15mm dia PVC connection 450/600 mm long all as specified.

S&F in repairs PVC waste pipe 32/40 mm dia for urinal

S&F in repairs PVC waste pipe 32/40 mm dia for WHB/Sink

S&F Vitreous china urinals, bowl type of size 465x355x265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern and waste pipe),complete including poviding and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with flushing cistern with brackets, flush pipe, waste pipe grating and union for discharge pipe fixed in repair, complete all as specified.

Taking down the existing bottle traps of wash hand basin refixing the same after cleaning including replacement of washers, packing etc if required complete all as specified & directed by Engr-in-charge.

S&F brass chromium plated bottle trap 32mm bore for wash hand basin with inlet and outlet and screwed for pipe or all as specified, fixed as in repairs complete all as specified and directed by Engr-in-Charge.

M&L in replacement of existing chromium plated grating of size 125mm dia (with hole or without hole) complete for Nahani/Floor traps and fixed as in repairs complete all as specified & directed by Engr-in-charge.

S&F in repair 70 mm dia fancy type shower roses brass chromium plated with CP arms for 15mm bore GI pipe with 235 mm long shower arm complete all as specified & directed by Engr-in-ChargeMake : Cera/Jaguar/Ess Ess

S&F in repair 15 mm dia two way bib taps (fancy type), cast copper alloy with with crutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule complete with check nut 15mm bore complete all as specified and directed by Engr-in-Charge.Make : Cera/Jaguar/Ess Ess

S&F in repair 15 mm dia bib taps (fancy type), cast copper alloy with with crutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule complete with check nut 15mm bore complete all as specified and directed by Engr-in-Charge.. Make : Cera/Jaguar/Ess Ess

S&F in repair bib tap of PTMT any colour 15mm dia (Prayag or equivalent ) in repairs all as specified.

S&F in repair stop valve of PTMT any colour screwed for iron pipe and fixed 15mm bore (Prayag or equivalent ) all as specified.

S&F in repair gun metal globe gate valve 20 mm bore.

S & F repair Wall mixer non telephonic Shower arrangement with connecting legs & Wall flanges, fixed in repairs. Make : Cera/Jaguar/Ess Ess

S&F in repair 15 mm dia CP Pillar taps (fancy type), cast copper alloy with capstan heads, chromium plated, handle screwed down high pressure, with or without lettered HOt or cold with long screwed shanks and fly nuts ,screwewd for crewed for iron pipe and fixed complete with check nut 15mm bore complete all as specified and directed by Engr-in-Charge.

S&F in repairs Angle cock with wall flange 15 mm dia Fancy type

S&F in repairs stop valves, chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed 15mm bore dia.

S&F in repairs stop valve 15mm dia fancy type chromium plated long shank and cup (concealed type)

S&F Paper holder with Flap Recessed Type (Stainless steel), in repairs, all as spd and directed by Engr-in-Charge.

S&F in repair Waste coupling for sink of 125mm dia complete all as specified

S&F Corner Glass shelf with bracket, in repairs, all as spd and directed by Engr-in-Charge. Make : Jaguar (Code No CAN-1173) or equivalent as approved by GE.

S&F in repair Sink with drainage board made of stain less steel 1mm thick kitchen or laboratories with plugs, washer and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915x 460x bowl size 410x330x160mm complete all as approved by Engr-in-Charge.

S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes;including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm omplete all as approved by Engr-in-Charge.

S&F in repair Stainless steel Plate Rack 0.75 Mtr x 0.78 Mtr .

S&F in repairs Decorative wooden finished curtain rod mild steel chromium plated of 20 mm dia all as directed and specified by Engr in charge.

S&F decorative wooden finished type chromium plated double brackets supports for holding curtain rods and Knobs of suitable colour and corners piece to be fixed to ends of curtain with screws complete.

M&L 12mm thick block boards grade 2 quality, interior grade decorative type with decovative face veneer on one face, fixed with screws to timber frame work all as specified and as directed fixed in repairs

M&L 19/20mm thick block boards grade 2 quality, interior grade decorative type with decovative face veneer on one face, fixed with screws to timber frame work all as specified and as directed fixed in repairs

S&F continuous (Piano) hinges mild steel, powder coated, width of flaps 30mm

Taking down steel rolling shutters push & pull type not exc 14 Sqm area of clear opening each including cover & cleaning the sides of shutter, suspension shaft and guide channel and greasing of the moving parts of rolling shutter and strainghtening of rolling shaft and tightening/replacement of ball bearing,bolts, nuts and any other defective parts as required for smooth functioning of shutter & refixing in same opening complete all as directed.

Removal and cleaning of vegetation, fungus, moss small trees etc from the roof top, chajja and removing spoils to a distance n.exc 100 m from the periphery of the single/Double story building.

M & L for Removing the existing unserviceable tar felt or any type of felt of any description from roof slab alongwith screed bed, including cleaning the surface & removing the debris to a distance exc 250m and n.exc 500m, etc complete all as specified & directed.

Material and labour for rendering 15mm thick (average) in cement mortar 1:4 on roof surfaces mixed with water proofing compound as per manufacturer's instructions, finished even and smooth without using extra cement. Note:- supply only of water proofing compound will be measured and paid seperately under relevant item

Supply only approved integral water proofing compound, Make : conplast x 421 IC of M/s Foroc Chemical (Inida) Ltd or its equivalent of make Dr Fixit/ STP Ltd.

M&L Applying oil bounded bitumen primer @ 0.20 Kg/Sqm, and providing 4mm thick APP modified water proofing membrane weighing not less then 4.0 Kg/Sqm, reinforced with non woven polyester matt weighing not less then 160 gm/sqm having softening point not less then 150 degree centigrade, having tensile strength of 650 N/5 cm and 350 N/5cm in longitudinal and transverse directions respectively of the reinforcement, trearing strength of 180 N by torch- on application including min 10cm side over lap & 15 cm end laps. Applying a coat of blown grade hot bitumen 90/15 over the membrane @ 1.2 Kg/sqm as per the detailed specifications. Note : The laying/ applying of APP membrane and other connected work shall be carried out by the approved applicator of the manufacturing company of APP membrane.

M & L for providing and injecting chemical emultion for post construction antitermite along the external of wall below concret or masonary apron using chemical emultion at the rate of 2.25 litre per linear meter including drilling and pluging holes etc complete all as specified and directed.

M&L for Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc capacity in exceeding 250 Ltrs n exc 500 ltr PVC/RCC water storage tank without dismantling the tank all as specified and directed by Engr -in-charge.

All as per item No.119 but capacity exceeding 500 Ltrs and not exceeding 1000 Ltrs.

All as per item No.119 but capacity exceeding 1000 Ltrs and not exceeding 2000 Ltrs.

S&F in repair PTMT Nipple 25 mm suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm- 45gms /25mm- 65gms) .

S&F in repair 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass in repair .

S&F in repair 25 mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass in repair.

S&F in repair rotational moulded polyethylene water storage tank 500 ltr capacity hoisted and fixed in position all as specified in SSR Pt - I including dismantling old tank.

S&F in repair rotational moulded polyethylene water storage tank 1000 ltr capacity hoisted and fixed in position all as specified in SSR Pt - I including dismantling old tank.

S&F in repair gun metal globe gate valve 25 mm bore.

Dismantling of plain or corrrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F prepainted galvalume alu zinc coating based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/claddding to wall, fix with self tapping screws with necessary washers/welding all as specified and directed. (The profile of the sheet as specifed and directed by Engr-in-Charge).

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. complete butt welded tubes conforming to IS 1161-1979 grade st-240 .

M&L for applying two coats of synthetic enamel paint over a coat of red oxide on new steel surfaces of any description cover 10cm in width of girth not Otherwise described.

M&L for one coat of synthetic enamel paint (1st grade quality) to old decorated wooden surfaces of any description ,not otherwise described over 10 cm width or girth incl preparation of surface complete.

M&L for one coat of synthetic enamel paint (1st grade quality) to old decorated steel surfaces of any description ,not otherwise described over 10 cm width or girth incl preparation of surface complete.

M&L for one coat of synthetic enamel paint (1st grade quality) to old decorated plastered surfaces of wall of any description ,not otherwise described over 10 cm width or girth incl preparation of surface complete.

M&L for one coat of white wash on old decorated surface of internal /External walls incl preparation of surface by scrubbing down on steel wire brushing scrubbing down smokes spots moulds, moss and efflorescent salts and treating oil and greasy spots all as specified and directed.

M&L one coat of white washing on old decorated ceiling surfaces incl preparation of surfaces.

M&L for two coat of white wash on old decorated surface of internal /External walls incl preparation of surface by scrubbing down on steel wire brushing scrubbing down smokes spots moulds, moss and efflorescent salts and treating oil and greasy spots all as specified and directed.

M&L for one coat of cement base paint to old decorated surfaces of wall incl preparation of surfaces complete all as specified and directed.

M&L for two coat of cement base paint to old decorated surfaces of wall incl preparation of surface & curing complete after complete removal/scarpping of existing treatment.

M&L old painted surfaces of wall washing rubbing down and stopping of distembered surfaces on walls,removing nails making good holes cracks etc and applying one coat of oil bound distempering on walls incl preparation of surfaces. All as speified and directed

M&L old plastered surfaces of wall washing rubbing down and stopping of distembered surfaces on walls,removing nails making good holes cracks etc and applying two coat of oil bound distempering on wallsincl preparation of surfaces. All as specified and directed.

M&L old painted surfaces of wall at one coat of oil bound distempering incl preparation of surfaces as in ceiling .

M&L for Complete removal of existing surface finish and applying 1-2 mm thick wall care putty at wall and ceiling surfaces all as specified and directed.

M&L for one coat of exterior paint to old decorated surfaces of wall ,floor, interlocking & chequred tile or incl preparation of surfaces complete all as specified and directed.

M&L for two coat of acrylic emulsion exterior paint all weather and water proof paint suitable for wall /concrete surface incl preparation of surfaces and over one coat of primer complete all as specified and directed.

M&L French polishing on surfaces of any description width or girth incl cleaning and preparation and polishing surface with one or more coat on old work, complete all as specified and directed.

Preparation of old painted concrete/plastered surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of plastic emulsion paint complete all as specified and directed.

M&L for Water based Road marking paint Viz., lines, Dashes etc on bituminous/ concrete surfaces not exceeding 10cm width or girth .

Writing letters or figures (Block, Roman, italic or Indian) n exc 30 cms height.

Writing stops, commas, short lines dashes, hyphens, brackets, etc.

S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165.

Cleaning of blocked / chocked Nahani trap / floor trap/WC/ Wash basin/, including drain / sewer / sewage line of any description (SGSW / RCC / CI pipe/SWR Pipe) of 75mm/100 mm / 150 mm / 200 mm dia and any depth by rodding or by mechanical means and well flushing the complete drain / sewer line upto first manhole to the entire satisfaction of Engineer – in - charge with and including taking out and re-fixing of manhole covers where required complete all as specified and directed.

Cleaning of manhole to manhole, using high pressure water jetting machine, including cleaning/ clearing blockages with all tools and labours as per the site requirement pipe size 150 mm and over including man holes through chasis mounted Diesel run vehicles mounted hydraulic operated high pressure suction cum geting sewer cleaning machine KAMBI-10 LCHB fitted with imported international standard pumps having minimum of 3000 litres to 4500 litres sucking capacity including skilled operator supervising engineer for cleaning/partial desiliting of manholes and sewer line as per guide lines laid in IS -11972 (1987) and complete cleaning of site all as directed by Engineer in charge -Note :- (a) Jetting of sewer line by high pressure jetting system of 2200w PSI/Suction. (b) The complaint has to be rectified with in 24 hrs from the complaint assign to the contractor failing which penalty will be imposed @500/- per complaint per day.

M&L for de-watering /de sluding of sewge well and septic tank of any size & approx 2 to 3 metre depth ,excavation of waste water from collection tank using 4500 litres to 5000 litres vaccum suction tanker, De watering of liquid or semi liquid waste by water sucking hydraulic pressure machine including cleaning of all sludge silt residue of both organic nature by manual labour or by mechanical scrappers etc in any position & disposal off all the waste outside the defeneland the de-sludging of sewage sump is to be carried out upto the bottom slab of sewage sump/ sewage well complete. The sewage well wall & bottom slab to be cleaned by water with high presurre up to entire satisfaction of Engr-incharge , neccessary safety precaution to be adhere during working. Note :- (a) Jetting of sewer line by high pressure jetting system of 2200w PSI/Suction. (b) The complaint has to be rectified with in 24 hrs from the complaint assign to the contracor failing which penalty will be imposed @500/- per complaint per day.

Taking off existing manholes covers & cleaning of manholes depth not exceeding 1 metre by de-watering and taking off the rubbish / sludge etc., removing the same up to 50 m distance and put into newly excavated pits of suitable size and covering with excavated earth and placing back in position the removed covers complete all as specified and directed.

Taking off existing manholes covers & cleaning of manholes depth exceeding 1 metre but n exc 2 metre by de-watering and taking off the rubbish / sludge etc., removing the same up to 50 m distance and put into newly excavated pits of suitable size and covering with excavated earth and placing back in position the removed covers complete all as specified and directed.

Taking off existing manholes covers & cleaning of grease pit (any type) not exceeding 1 metre depth by de-watering and taking off the rubbish / sludge etc., removing the same up to 50 m distance and put into newly excavated pits of suitable size and covering with excavated earth and placing back in position the removed covers complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime moratr including all quoins, arches, pillars, etc but excluding ashlar facings dressed stone work and prcast concrete articles complete all as specified and directed.

M&L Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar, 1:6 type C1 1:3:6 (20 mm grared aggregate) complete all as specified.

Brickwork with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in CM 1:4.

All as per item No 162 abvoe but as in one and half brick thick honey comb walling in cm (1:4) .

M&L old broken brick bats/aggregates of size 80 to 150 mm in soakage pits, soakage wells.

M&L for loose filling with broken bricks aggregats or gauge 80 to 150 mm in soakage pits, soakage wells.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed.

Demolition of reinforced cement concrete in any position and any description including cutting of reinforcement bars to facilitate demolition complete all as specified and directed.

M & L for providing pre-cast cement concrete landing, cover slabs for manholes, chullah hoods, chajjas, shelves and similar items with plain faces in cement concrete 1:2:4 type B-1, using 20 mm graded crushed stone aggregate and setting in cement mortar 1:6 including necessary form work complete all as specified and directed.

M&L Reinforced cement concrete Type B1 1:2:4 ( 20 mm graded aggregate) Slabs supported on walls, beams and columns in floors,roofs,andings,balconies,canopies, deck slabs and in shelves and the like.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work: not exceeding 200mm thick (Horizontal or sloping & Flat) rough finished surfaces .

M & L for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 6 to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Demolition and breaking up drain pipes internal dia of pipe in 150mm (salt glazed ware, AC or reinforced concrete ) set in cement mortar complete.

Demolition and breaking up drain pipes internal dia of pipe in 200mm (salt glazed ware, AC or reinforced concrete ) set in cement mortar complete.

M&L for 150mm dia reinforced concrete pipes class NP-2 for following dia of pipe laid and jointed complete with collars all as specified and directed.

M&L for 200mm dia reinforced concrete pipes class NP-2 for following dia of pipe laid and jointed complete with collars all as specified and directed.

M & L for cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) for 150mm dia pipe concrete bed to drain pipes of including packing under and haunching against the sides of pipe after they are laid and tested including necessary form work for the following bore of drain complete all as specified and directed.

M & L for cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) for 200mm dia pipe concrete bed to drain pipes of including packing under and haunching against the sides of pipe after they are laid and tested including necessary form work for the following bore of drain complete all as specified and directed.

M & L for providing plain cement concrete, type D-2, 1:4:8 (using 40 mm graded crushed stone aggregate) as in sub base of floor, foundation, filling and mass concrete complete all as specified and directed.

M & L for providing plain cement concrete type B-1, 1:2:4, (using 20 mm graded crushed stone aggregate), as in benching, coping, channel of manholes and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M&L 100 mm thick PCC type B-2, 1:2:4 (using 40 mm graded aggregate) as in path, hardstanding, bed Complete all as specified and directed.

M&L for 50mm thick Plain Cement concrete 1:3:6, type C2 (using 40 mm graded stone aggregate) as sub base of floor .

M&L for 75mm thick Plain Cement concrete 1:3:6, type C2 (using 40 mm graded stone aggregate) as sub base of floor .

M&L for sand filling under floors or in foundation including watering and consolidation.

M&L for Machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658 - 2006 of 60 mm thickness, M - 35 Grade with grey cement and no pigment.

M&L for 15mm thick Screed bed or bedding layer of mortar in CM 1:6 for laying floor finish.

M&L for chequered tiles of size 300x300x 25 mm thick, set and jointed in neat cement slurry in floors and pointed in white or coloured cement to match with grey cement and no pigment all as specified and directed.

M&L for heavy duty tiles of size 300x300x 10 mm thick, in floors/ wall/ skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and directed. (Make:Somany/Johnson/Equivalent).

M & L for cutting into existing manhole for connecting new drain, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150 mm dia pipe complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed.

M&L High dencity polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to wall,ceiling or floors etc.50 mm bore pipe.

S&F PVC (SWR) gully trap size 125/110 mm setting and jointing with solvent cement in repair.

S&F PVC (SWR) vent cowl 75mm dia including taking down old unsuitable vent cowl as in repairs.

S&F PVC (SWR) vent cowl 110 mm dia including taking down old unsuitable vent cowl as in repairs.

S&F PVC waste pipes 32/40 mm dia for urinal, WHB or sink, 600 mm long.in repairs.

S&F PVC (SWR) 110mm dia bend any radius in repairs.

S&F PVC 75mm dia (SWR) bends any radius in repairs.

S & F PVC(SWR)110 mm singleT in repairs.

S&F PVC(SWR) 75 mm single T in repairs.

S&F PVC(SWR) 110mm dia branch pieces single (Single Y) equal or unequal in repairs.

S&F PVC(SWR) 75 mm dia branch pieces single (Single Y) equal or unequal in repairs.

M&L 75 MM PVC (SWR) floor trap, plain with grating including jointing with solvent cement as in repairs.

S&F in repairs Grating dome 100 mm dia stainless steel with or with out hole all as specified.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation etc. or for manholes, cesspits, shafts etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

All as item No 206 above but depth exceeding 1.50 metre but not exceeding 3.00 metre and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soft / loose soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

chowdeshwariconstructionco

SRI MAHALAKSHMI CONSTRUCTIONS

P K CONSTRUCTIONS