SPECIAL REPAIR TO EXISTING EXPANDABLE STORE SHED BUILDING OF MMG AT R AND DE DIHGI AND CERTAIN MINOR WORK INCLUDING REVENUE WORKS AT R AND D DE DIGHI PUNE

Amount

SPECIAL REPAIRS TO EXISTING EXPANDABLE STORE SHED BUILDING OF MMG AT R&DE (E) DIGHI, PUNE-15 (B&R PORTION) Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of Cement Concrete Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground out side the MD land initial lead, for all leads including all lifts involved complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for 75mm thick Cement concrete type B- 2, 1:2:4 (using 40mm graded stone aggregate) as in flooring/ Hardstanding and finishing the surface even and smooth without using extra cement complete all as specified and directed.

S&F 38mm width Glass dividing strips, 3 mm thick and inserted in position, conform to design complete all as specified and directed.

M&L for 75mm thick Cement concrete type C- 2, 1:3:6 (using 40mm graded stone aggregate) as in plinth protection complete all as specified and directed.

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound of grade A quality complete all as specified and directed.

M&L for Cement concrete type B- 1, 1:2:4 (using 20mm graded stone aggregate) as in coping, string course, sesmic bands, Holdfast etc and similar positions including necessary for work complete all as specified and directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe-290 (Gde E-165) complete all as specified and directed.

S&F Steel rolling shutters, with ball bearing, as specified including top cover, an?choring rod, hasp and staple and one shop coat of primer; erected in position as indi?cated, complete: gearoperated type with bevel gear box and crank handle (Thickness of laths 1.0mm) complete all as specified and directed.

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces of any description in CM 1:6 and finishing the surface even & smooth w/o using extra cement complete all as specifiied and directed.

M&L rendering 10mm thick in cm 1:4 on brick or concrete of any description mixed with WPC @3% by weight of cement and finishing the surface even and fair without using extra cement complete etc all as specified and directed. Note: WPC will be measured and paid seperately

Supply only integral water proofing compound of approved make complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of exterior acrylic emulsion over a coat of exterior acrylic primer after preparation of surfaces at any height including necessary scafolding etc complete all as specified and as directed by Engineer-in-Charge. Make : Asian/ Appex ultima' or equilant.

M&L for complete removal of existing treatment on wall surfaces, fins, fascias etc by scrubing, sand papering and applying two coats of weather proof exterior paint white or tinted over a coat of acrylic exterior primer incl nescessary scafolding all as specified and directed. Make : Asian/ Appex ultima' or equilant.

M&L for preparation of newly plastered wall surface and applying three coats of white wash complete all as specified and directed.

M&L for complete removal of existing treatment including Washing, rubbing down and stopping etc. and applying two coats white wash on walls complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old painted surfaces of steel & iron of any description over 10cm width or girth and applying one coat of synthetic enamel paint (1st quality) etc all as specified and directed.

S&F for Pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified including corrugated ridge sheeting complete all as specified and directed.

All as per Item No 23 here in before but except sheeting complete all as specified and directed.

M&L Preparation of new or previosly untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Provision of 02 Nos Temporary roof toilet facility near married colony entrance at R&DE (Engrs) Dighi, Pune (B&R PORTION) M&L for surface dressing n exc 15 cm deep in soft/ loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in hard/ dense soil complete all as specified and directed.

M&L for Cement concrete 1:2:4 type B2 (using 40mm graded stone aggregate) as in foundation, mass concrete complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry with solid blocks 1:3:6 type C1 using 20mm graded stone arregate, exc. 10 cm in width and setting in cement mortar 1:4, complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggrgate) as in copings, damp proof coarse, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and directed.

M&l for Moorum/red bajri filling in floors or pavings, laid in layers n exc.15 cm thick spread, levelled and rammed including watering complete all as specified and directed.

M&L for broken stone Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick Cement concrete type D2, 1:4:8 (using 40mm graded stone aggregate) as in floor complete all as specified and directed.

M&L for 30mm thick Cement concrete type B1, 1:2:4 (using 20mm graded stone aggregate) complete all as specified and directed.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth w/o using extra cement complete all as specified and directed.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 in two layers (10mm + 5mm) using WPC @3% by weight of cement finished even & fair w/o using extra cment all as specified and directed and finishing the surface fair Note : WPC shall be measured and paid seperatly as supply only under relevent item of this BOQ Schedule.

M&L for preparation of newly plastered wall surface and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered wall surface and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and directed.

S&F 15mm bore GI tubing medium grade with all fittings and fixed complete to walls and ceilling or laid in floors complete all as specified and directed.

S&F 20mm bore GI tubing medium grade with all fittings and fixed complete to walls and ceilling or laid in floors complete all as specified and directed.

S&F in repairs Vitreous China wash basin, white, flat back, size 580x450mm including brackets, including cutting for and pinning in ends of brackets or erecting stand and including 15mm bore CP fancy type pillar tap, 32mm bore waste coupling of PTMT (half or full threaded) Minimum weight 32mm-45gms/40mm-60 gms) with waste pipe of required length and PVC connections 15mm size with brass nuts of length 450mm etc complete all as specified and directed.

S&F in repairs 10 litres capacity PVC low level flushing cistern valve less syphonic action type, white with inlet, ball valve, float and handle, bracket, etc including flush pipe of PVC 32 mm bore of suitable length and connecting to water closet complete all as specified and directed.

S&F in repairs vitreous china squatting pan Orrisa Pattern, WC white, of size 580 x 440mm with integral foot rests,including ' P' or ' S' trap complete including lime concrete bedding complete all as specified and directed.

S&F 110mm bore single socket PVC (SWR) pipe, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F PVC (SWR) bends any radius of 110mm bore complete all as specified and directed.

S&F 75mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

M&L non skid coloured ceramic tlies 7 to 8 mm thick (Square/rectangular ) area of each tile exceeding 0.06 sqm but n.exceeding 0.11 sqm in floors etc. set and jointed in net cement slurry and pointed in white coloured cement to match coloured tiles with and over 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for glazed, coloured (including desiner tiles as approved by GE) ceramic tiles in verticle surface of size 300 x 450/ 600 x 7 to 8mm thick set and joined in neat cement slurry and pointed in cement slurry and pointed in white or coloured cement to match over 20mm thick cement plaster in CM 1:4 complete all as specified and directed.

S&F Vitreous China urinals, half stall type, complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F 15mm bore Conclussive push button taps of cast copper alloy, screwed for iron pipe and fixed complete all as specified and directed.

S&F 15mm bore Stop valves, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 300mm complete all as specified and directed.

S&F CP Tabular towel rail 20mm dia 'D' type 60 cm long between flanges all as directed complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F 3mm thick Figured glass, pin head type and glazing with oil putty in squares in n.exc 0.5 sq.m in each pane complete all as specified and directed.

S&F PVC double door frame of size 50mm X 95mm made out of 5mm wood grain printed PVC sheet reinforced with MS tube complete all as specified and directed.

Supply and Fixing of factory made solid panel PVC door 30 mm thick consisting of frame made out of MS tube for top & bottom rail MS frame shall be covered with wood grained PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail , lock rail & bottom rail on either side & as gap insert for top & bottom rail . Panelling of wire gauged wood grained PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails as suitable. The wire gauge shall be wrapped on additional square 8mm MS solid tube and this tube shall be welded to MS tubes. The wire gauge shall be streched and tighten firmly complete all as specified and directed.

S&F Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified, supplied and fixed complete all as specified and directed.

M&L for PCC 1:3:6 Type C0 (using 12.5mm graded stone aggregate) for filling in presssed steel door frames complete all as specified and directed.

S&F MS hold fasts conforming to Fe -410 all as directed by Engineer In Charge

M&L for cement concrete Type B0 1:2:4 (using 12.5mm graded stone aggregate) as in bed plates complete all as specified and directed.

M&L for treating small articles such as hold fasts with tar or coal tar black paint incl preparation complete all as specified and directed.

S&F 30mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 100mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F 300mm long aluminum alloy anodised sliding door bolt with hasp & stapple (bolt type) and fixing clips ofsheet, cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type anodised 150 mm size complete all as specified and directed.

S&F 150mm long floor door stopper of brass body and tongue with hard drawn steel spring complete all as specified and directed.

M&L for preparation of newly or untreated wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer of girth or width exc 10cm complete all as specified and directed.

M&L 75mm thick for Cement concrete type C-2, 1:3:6 (using 40mm graded stone aggregate) as in plinth protection complete all as specified and directed.

M&L for Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Gde A complete all as specified and directed.

Supply only Liquid water proofing compound of approved make complete all as specified and directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Conforming to GDE Fe-410-W (Grade E-250) complete all as specified and directed.

M & L preparation of new steel surfaces and applying two coats synthetic enamel paint over a coat of red oxide primer of any description over 10cm in width or girth not otherwise described complete all as specified and directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for RCC lintel band (nominal mix) type B1 1:2:4 (using 20mm graded stone aggregate) including necessary formwork all as specified and directed.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per Item No. 80.00 here in before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for reinforced cement concrete type B1 1:2:4 (using 20mm graded stone aggregate) as in Foundations, including rafts footings, foundation beams; plinth beams; bases for columns, etc basement slabs under-reamed piles and mass concrete complete all as specified and directed.

M&L for rough finished flat surface Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

S&F 15mm bore Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

Provision of covered shed for 22KV RMU at technical area at R&DE (Engrs) Dighi, Pune M&L for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard / dense soil complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard / dense soil complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry with solid blocks 1:3:6 type C1 (using 20mm graded stone aggregate) exc. 10 cm in width and setting in cement mortar 1:4, complete all as specified and directed.

M&L for broken stone Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100mm thick Cement concrete type B2, 1:2:4 (using 40mm graded stone aggregate) as in hard standing/ flooring and finishing the surface even and smooth withou using extra cement complete all as specified and directed.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth w/o using extra cement complete all as specified and directed.

M&L for preparation of newly plastered wall surface and applying two coats of cement based paint complete all as specified and directed.

M&L for Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Gde A complete all as specified and directed.

M&L for cement concrete Type C2 1:3:6 (using 20mm graded stone aggregate) as in post holes, mass concrete, etc complete all as specified and directed.

M&L for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Conforming to .Fe-290 E( Gde E-165) complete all as specified and directed.

S&F for Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.Fe-290 E( Gde E-165) complete all as specified and directed.

M & L for preparation of new steel surfaces and applying two coats synthetic enamel paint over a coat of red oxide primer of any description over 10cm in width or girth not otherwise described complete all as specified and directed.

M&L for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including noth curve sections in end slides complete all as specified and directed.

M&L for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

SPECIAL REPAIRS TO EXISTING EXPANDABLE STORE SHED BUILDING OF MMG AT R&DE (E) DIGHI, PUNE-15 (E&M PORTION, INTERNAL ELECTRIFICATION) Taking down carefully unserviceable sub main wiring including conduit from ground etc complete all as specified and directed.

Taking down unserviceable DBs/MCB SP/SPN/Isolator of any rating & size carefully disconnecting and making good disturbed surfaces complete all as directed.

Taking down Copper/ aluminium point wiring (light/ fan/socket or power) complete including fixture and fittings such as switches, sockets, ceiling roses pendent / brackets holders, regulators, unsv light fittings, etc removing material for taking credit and making good disturbed surfaces of walls, floors etc all as directed.

M & L Point wiring complete with 1.5 sqmm single core PVC insulated and unsheathed cable 1100 volts, FRLS grade with multistranded copper conductor ISI marked drawn through PVC concealed conduit fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm stranded copper conductor cable as earth continuity conductor and connected to common earth dolly, including modular cover plates with frame and modular flush boxes for mounting for housing the switches, socket outlets, fan regulators etc, all as specified and directed. Note :- Contractor's quoted rate shall deemed to be inclusive the cost of cutting chases to the extent required and making good the surface as per existing finish etc complete all as specified and directed.

(a) One light point controlled by one switch complete all as specified and directed.

(b) One fan / Exhaust fan point controlled by one switch and one regulator complete all as specified and directed.

(c) One 3 pin switch socket outlet point 5 Amps on independent board complete all as specified and directed.

(d) One 3 pin switch socket outlet point 5 Amps on same board with other switch complete all as specified and directed.

All as per item above here in before but with copper conductor cable for one 3 pin socket outlet, 15 amp independent, with cable 2.5 sqmm size complete all as specified and directed.

S & Fix modular switch 1 way 6A, 1 module complete all as specified and directed.

S & Fix modular switch1 way 16A, 1 module complete all as specified and directed.

S & Fix modular socket out let 6A 2/3 on combined 2 module complete all as specified and directed.

S & Fix modular socket out let 6A/16A-2/3 pin combined 2 module complete all as specified and directed.

S & Fix ceiling rose surface backlite 65x50 mm 3 terminals complete all as specified and directed.

Supply and fixing in replacement of existing unserviceable T/L fitting 36/40 W on existing pole/wall with LED light fitting 18/20 watts with LED tube rod, ready to use pack with necessary braket,clamps ,incl. bolts, nuts & washers for fixing arrangement etc complete all as specifed and directed by Engineer-in-charge. Make :- Halonix Cat No HLB-03-18CW-AL-SQ-HL2 or equivalent in Wipro/philips/Havells/Jaguar as approved.

S & Fix LED street light 30 W building security light pressure die cast aluminium housing with high power LEDs, lens, & toughened glass, with IP 66 and bracket, nut,bolt,clamp etc complete all accessories and fixing arrengenment all as specified and directed by Engr-in-charge. Make - Halonix / Havells/ Bajaj as approved

M & L Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required complete all as specified and directed.

(a) 2 x 1.5 sqmm + 1 x 1.5 sqmm earth wire

S&F Exhaust fan AC single phase 240 V, 300 mm sweep, Heavy Duty with louvers, including connected with 3 core 1.5 sq mm copper conductor cable from ceiling rose to exhaust fan fixed on cutting hole of suitable size in masonary wall and making good surface in 1:3 CM and fixing arrangement complete all as specified & directed. Make - Usha aroclean plus or equivalant in Havells/Crompton/ Bajas as approved.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required and all as directed

Supplying and fixing 12 way, Double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) as directed.

S&Fix sheet metal enclosure distribution board SPN, 2 ways 240 volts, with 100 amps rated bus bar, with IP 43 protection and double door, suitable for mounting MCBs including taking down old MCB DB complete as directed.

S & Fix MCB, single pole, 240 volts, 6 to 32 Amps, all as specified and as directed.

S & Fix MCB single pole & neutral, 240 volts, 6 to 40 Amps, all as specified and as directed.

(EXTERNAL ELECTRIFICATION ) Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 3 including excavation & earthwork, returning filling & removal of surplus soil etc complete all as specified & directed.

Supplying and embedding 32 mm dia G.I. pipe (medium grade) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required and all as directed.

Supply & Laying 40 mm outside dia double wall corrugated pipe (DWC) of HDPE ISI Mark for enclosing cable below ground / road surface, to a required depth, including suitable size coplers for jointing of pipe all as per site requirement and as directed.

M & L for galvanised steel earthing complete with 60 cm x 60 cm x 6 mm thick galvanised steel earth electrode and 04 mm dia galvanised earth lead wire burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to earth lead 4.0 mm dia GI wire protected by 15 mm bore light grade galvanised iron pipe and other and connected to test point as directed including funnel with watering pipe 20 mm bore light grade galvanised iron wire mesh, charcoal and common salt in alternater of 15 cm complete thickness all around the GI plate electrode complete with earth pit PCC 1:3:6 type CI and RCC 1:2:4 type B1 as in cover 50 mm thick with & including reinforcement with 8mm dia TMT bar at 75 mm spacing both ways and necesary excavation and earth work in hard/dense soil and disposal of spoil to a distance not exc 50 mtr and necessary testing complete all as shown in electorical plate No 03 connected to earthing test point including taking out old U/S earthing material all as directed. Note. Cost of earth lead and protection pipe upto 7.5m shall deemed to be included in quoted rate.

Material and labour for cutting of bituminous road / floor / culvert / PCC hard standing for laying of pipe / cables not exceeding 1.5 meter wide and not exceeding 1.5 meter deep including refilling / with material and , watering well ramming / compacting and making good with PCC 1;2;4,type B-1, 100 mm thick complete all as specified and directed by Engr-in-Charge.

PROVISION OF 02 NOS TEMPORARY ROOF TOILET FACITLITY NEAR MARRIED COLONY ENTRANCE AT R&DE (ENGRS) DIGHI, PUNE (E&M PORTION, INTERNAL ELECTRIFICATION) S&F Exhaust fan AC single phase 240 V, 250 mm sweep, PVC Body with louvers, including connected with 3 core 1.5 sq mm copper conductor cable from ceiling rose to exhaust fan fixed on ventilator and fixing arrangement complete all as specified & directed. Make- Havells ventil Air DX or equivalant in USHA/Crompton/Bajaj as approved.

M & L Point wiring complete with 1.5 sqmm single core PVC insulated and unsheathed cable 1100 volts, FRLS grade with multistranded copper conductor ISI marked drawn through PVC concealed conduit fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm stranded copper conductor cable as earth continuity conductor and connected to common earth dolly, including modular cover plates with frame and modular flush boxes for mounting for housing the switches, socket outlets, fan regulators etc, all as specified and directed . Note. Contractor's quoted rate shall deemed to be inclusive the cost of cutting chases to the extent required and making good the surface as per existing finish etc complete all as specified and directed.

(a) One light point controlled by one switch.

(b) One fan / Exhaust fan point controlled by one switch and one regulator.

(c) One 3 pin switch socket outlet point 5 Amps on independent board.

(d) One 3 pin switch socket outlet point 5 Amps on same board with other switch.

S & Fix modular switch 1 way 6A, 1 module all as specified and directed.

S & Fix modular socket out let 6A 2/3 on combined 2 module all as specified and directed.

S & Fix ceiling rose surface backlite 65x50 mm 3 terminals complete all as specified and directed.

Supply and fixing in replacement of existing unserviceable T/L fitting 36/40 W on existing pole/wall with LED light fitting 18/20 watts with LED tube rod, ready to use pack with necessary braket,clamps ,incl. bolts, nuts & washers for fixing arrangement etc complete all as specifed and directed by Engineer-in-charge. Make :- Halonix /Wipro/philips/Bajaj/Havells as approved.

Supply and fixing in replacement of existing unserviceable T/L fitting 10 W on existing pole/wall with LED light fitting 10 watts with LED tube rod, ready to use pack with necessary braket,clamps ,incl. bolts, nuts & washers for fixing arrangement etc complete all as specifed and directed by Engineer-in-charge. Make :- Halonix/ Wipro/philips/Havells/Bajaj as approved.

Supplying and fixing 8 way, Double door single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) all as directed.

S & Fix MCB single pole, 240 volts, 6 to 40 Amps, all as specified and as directed.

S & Fix MCB single pole & neutral, 240 volts, 6 to 40 Amps, all as specified and as directed.

S & Fix LED street light 30 W CUB type building security light pressure die cast aluminium housing LED street light lumaniries with IP 65 and bracket, nut,bolt,clamp etc complete all accessories and fixing arrengenment all as specified and directed by Engr-in-charge. Make - Havells/Holonix/ Bajaj/ Crompton/Wipro as approved.

PROVISION OF 02 NOS TEMPORARY ROOF TOILET FACITLITY NEAR MARRIED COLONY ENTRANCE AT R&DE (ENGRS) DIGHI, PUNE (E&M PORTION, EXTERNAL ELECTRIFICATION) Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 3 core including excavation & earthwork, returning filling & removal of surplus soil etc complete all as specified and directed.

Supply & Laying 50 mm outside dia double wall corrugated pipe (DWC) of HDPE ISI Mark for enclosing cable below ground / road surface, to a required depth, including suitable size coplers for jointing of pipe all as per site requirement and as directed.

Supplying and embedding 32 mm dia G.I. pipe (medium grade) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required & all as directed.

M & L for galvanised steel earthing complete with 60 cm x 60 cm x 6 mm thick galvanised steel earth electrode and 04 mm dia galvanised earth lead wire burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to earth lead 4.0 mm dia GI wire protected by 15 mm bore light grade galvanised iron pipe and other and connected to test point as directed including funnel with watering pipe 20 mm bore light grade galvanised iron wire mesh, charcoal and common salt in alternater of 15 cm complete thickness all around the GI plate electrode complete with earth pit PCC 1:3:6 type CI and RCC 1:2:4 type B1 as in cover 50 mm thick with & including reinforcement with 8mm dia TMT bar at 75 mm spacing both ways and necesary excavation and earth work in hard/dense soil and disposal of spoil to a distance not exc 50 mtr and necessary testing complete all as shown in electorical plate No 03 connected to earthing test point including taking out old U/S earthing material . Note. Cost of earth lead & protection pipe upto 7.5m shall deemed to be included in quoted rate.

Material and labour for cutting of bituminous road / floor / culvert / PCC hard standing for laying of pipe / cables not exceeding 1.5 meter wide and not exceeding 1.5 meter deep including refilling / with material and , watering well ramming / compacting and making good with PCC 1;2;4,type B-1, 100 mm thick complete all as specified and directed by Engr-in-Charge.

PROVN OF LEX GARDEN LIGHT, LED POST TOP, LED FLOOD LIGHT, LED STREET LIGHT, LED BLDG SECURITY LIGHT AT SURROUNDING OF OFFICER MESS, SPORTS MESS, SPORTS COMPLEX AT R&DE (E) DIGHI, PUNE-15 Supply & fix LED 8W decorative garden light LED bollard in round shaped victorian design with opel acrylic diffuser and IP 65 protection, resistance to impact and corrosion, glare free and better uniformity includes necessary PCC foundation for fixing of light fitting with suitable type junction box, connecting wires etc. all as directed and specified. Make- Havells Cat No- CONE LED BOLLARD or equivalent in Bajaj/Halonix/Crompton/Wipro as approved.

Supply & fix LED 35W decorative post top lantern for 360 degree indirect light, made in cast aluminium with decorative opal polycarbonate diffuser with IP 65 protection, resistance to impact and corrosion, glare free and better uniformity all as directed and specified. Make- Havells Cat No - RUBY LED POST TOP or equivalent in Crompton/Wipro as approved.

Supply and fixing in replacement of existing unserviceable HPSV/metal hallied lamp fitting of any wattage on existing pole with 150 watts Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP66 flood light, suitable for highlighting architectural facade and general purpose lighting. with necessary braket ,clamps duly painted with two coats of aluminium paint over a coat of red oxide primer including 3 core 6 Sqmm PVC copper cable with PVC upto 7.5m for connection, bolts, nuts & washers for fixing arrangement etc complete all as specifed and directed by Engineer-in-charge. Make- Havels Cat No JETA IRIS or equivalent in Bajaj/Holonix/Crompton/Wipro as approved.

Supply and fixing in replacement of existing unserviceable HPSV/CFL/LED lamp fitting of any wattage on existing pole with LED light fitting 70 watts IP 66 with necessary braket ,clamps duly painted with two coats of aluminium paint over a coat of red oxide primer,incl. bolts, nuts & washers for fixing arrangement etc complete all as specifed and directed by Engineer-in-charge. Make:- Havells or equivalent in Crompton/Wipro/Bajaj as appoved.

Supply and Fix New generation energy saving and environmental friendly long life 30w LED street light made up of pressure diecast aluminium housing with highly efficient LEDs as Lighting Source and PC cover with integrated lens with IP66 protection and impact resistance of IK07 complete all as specifed and directed by Engineer-in-charge. Make: Havells or equivalant in Crompton/Wipro/ Bajaj as approved.

Supply and Laying and testing cable XLPE insulated heavy duty electric cables with multistanded aluminium conductor, 1100 volts grade, of following cross sectional area including connecting lugs, glands,jointing materials etc, laid on surface,wall, floors, roof, ducts trenches and fixing using clamps, saddle complete all as directed by Eng-in-charge.

(a) 6 Sqmm, 2 core

(b) 10 sq mm 4 core

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr depth and getting out in Hard / dense or any type of soil including forming bottom surface etc complete all as specified and directed.

Returning, filling in including spreading, levelling ,watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

Removing excavated material not exceeding 50 mtr and depositing where directed at a level not exceeding 50 mtr above the starting point complete all as specified and directed.

Supply & Laying 50 mm outside dia double wall corrugated pipe (DWC) of HDPE ISI Mark for enclosing cable below ground / road surface, to a required depth, including suitable size coplers for jointing of pipe all as per site requirement complete all as specified and directed.

Supply &Fix 3 core 2.5 Sqmm PVC insulated sheathed multicore copper flexible cable connected with existing point as directed by Engineer-in-charge.

M&L for submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable , multistranded on the surface recess through and including suitable size of PVC casing and capping/PVC conduit with its accessories all as specified and directed for the size 2x1.5 sqmm + 1x1.5 sqmm earth wire

Supply and fix PVC sintex junction box with one SP 6 amps MCB & terminals including proper fixing arrangements etc complete all as specified and directed.

PROVISIONING OF ELECTRIC GEYSERS (10 Nos) & EXHAUST FANS (10 Nos) IN 180 B DSC MARRIED ACCOMODATION AND DSC SINGLE ACCOMMODATION AT R&DE(ENGRS) DIGHI PUNE S&F exhaust fan, AC, single phase, 240 V, 230 mm sweep, metal body with metal blades metal louvers, including connected with 3 core 1.5 sq mm copper conductor cable from ceiling rose to exhaust fan all as specified and as directed. Make : Havells ventilair DS or equivalant in USHA/Crompton/Bajaj as approved.

M& L for Making hole/cutting/drilling in the existing wall including plastering and making the wall matching with the existing wall suitable for fixing the exhaust fan and louvers all as directed.

S & Fix water heater storage type, electric capacity 25 liters BEE 5 Star rated and bracket, nut,bolt,clamp, fasner, shock safe plug etc, complete all accessories and fixing arrengenment with 02 feet hot cum cold water connections, stop cock, nececeesary CPVC pipe line work with one steel water tap to be cutting and tapping from existing cold water line all other necessary fixing and functiong complete arrangemens including masonary work and all other required works all as specified and directed by Engr-in-charge. Make: Havells PURO EX or equivalant in Racold/Crompton as approved.

M &L for Point wiring complete with 1.5 Sqmm single core unsheathed PVC insulated, FRLS grade with multistranded copper conductor ISI marked drawn through PVC Conduit recess/surface fixed modular cover plates and modular flush boxes for mounting of switches, sockets regulators etc including 1.5 Sqmm PVC insulted unsheathed cable multistranded with copper conductor and connecting to earth dolly for light, fan, plug and bell and making good the distributed surfacess completely matched and finished with existing surfacess all as directed and specified by Engr-in-charge.

(a) Exhaust Fan point controlled by one 6 Amps switch.

All as per above item No-156.00 above but with 2.5 Sqmm cable for 16 Amp switch socket out let point on independent board including 2.5 Sqmm PVC insulated unsheathed cable multistranded with copper conductor earthing continuity conductor all as specified and directed.

Supply and fixing modular switch 6 Amps all as specified and directed. .

Supply and fixing modular switch 16 Ampsall as specified and directed.

Supply and fixing switch socket out let 2 / 3 pin 6 and 16 Amps 2 modular type all as specified and directed.

Supply and fixing ceiling rose ,3 phase ,PVC polycarbonate ,insulated body all as specified and directed.

PROVISION OF LED LIGHT AT SURROUNDING OF 4 Nos Bldg (ETH,CTF,MMG and Saranga),MAJOR QTRS.(P-145,P-194,P-193) AND CAPTAINS QTRS.(P35) AT R&DE ( E) DIGHI, PUNE-15 Supply and Fix New generation energy saving and environmental friendly long life 30w LED street light made up of pressure diecast aluminium housing with highly efficient LEDs as Lighting Source and PC cover with integrated lens with IP66 protection and impact resistance of IK07 all as directed. Make: Havells or equivalant in Wipro/Philips/Bajaj as approved.

Supplying and fixing of 32 mm dia X 1.2 metres long G.I. pipe (medium grade) bracket for mounting of LED street light fitting on pole including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint,etc. as required & directed.

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required & directed.

M&L for submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable , multistranded on the surface recess through and including suitable size of PVC casing and capping/PVC conduit with its accessories all as specified and directed for the following

(a) 2x1.5 sq mm and 1x1.5 sq mm as earth wire

(b) 2x2.5 sq mm and 1x2.5 sq mm as earth wire

PROVISION OF COVERED SHED FOR OFFICE PURPOSE IN ICTG BLDG NO. P-226 AT R&DE (E) DIGHI PUNE (B&R PORTION). Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid and bedded and pointed in any mortor complete all as specified and directed.

M&L 75 mm thick cement concrete type D2 1:4:8 ( using 40mm graded stone aggregate) as in sub base concrete all as specified and as directed.

M&L 25 mm thick cement concrete type B1 1:2:4 ( using 20mm graded stone aggregate) as in sub base concrete all as specified and as directed.

M&L for double charged Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and over 15mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per Item No 169.00 here in before but for skirting/ dado tiles with and over 10mm thick plaster in CM 1:3 complete all as specified and directed.

Taking down cement mortor plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6 including sagol finishing on plastered surface and preparation of newly plastered wall surface and applying two coats of water based emulsion paint over a coat of interior primer complete all as specified and directed.

Complete removal of existing decorated surface (of any type) and M&L for preparation of old decorated wall surface and applying two coat of oil bound distemper over chalk whiting over a coat of primer complete all as specified and directed.

M&L for applying 3mm thick (2mm +1mm ) interior wall care putty of approved make after preparation of surface complete all as specified and directed.

S & F plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases, splices, angle brackets, cleats and other connections. Conforming to GDE Fe-410-W (Grade E-250) complete all as specified and directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Conforming to GDE Fe-410-W (Grade E-250) complete all as specified and directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment GDE Fe-410-W (Grade E-250) complete all as specified and directed.

M & L preparation of new steel surfaces and applying two coats synthetic enamel paint over a coat of red oxide primer of any description over 10cm in width or girth not otherwise described complete, all as specified and directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm long but n exc 10cm and dia of neck exc 16mm complete all as specified and directed.

S&F Anodised aluminium (powder coated min 50 micron) frame for doors and windows with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F fixed type (only for provision of 5.5mm thick glass) Anodised aluminium (powder coated min 50 micron) window shutters (min 16 gauge sections) including joining cleat for fixing, rubber neoprene packing, standared rollers etc and necccesary fittings and fixtures etc. all as specified and directed Note for item No. 181.00 & 182.00 above : Plain glass as required will be measured and paid seperately.

S&F 5.5mm thick Sheet glass, ordinary quality and glazing in aluminium frame work in square n exc 0.5 sq. m in each pane complete, all as specified and directed.

S&F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete, all as specified and directed.

S&F two track Anodised aluminium (powder coated min 50 micron) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, rollers, etc anodised aluminum snap beading screws etc. including aluminium anodised body 100mm, 4 levers mortice lock complete, all as specified and directed. Note : Plain glass as required will be measured and paid seperately under relevant item of this schedule.

S&F Collapsible steel gates, top hung, consisting for channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets complete all as specified and directed.

S&F 110mm bore single socket PVC (SWR) pipe, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F PVC (SWR) bends any radius of 110mm bore with door complete, all as specified and directed.

All as per Item No 188.00 here in before but Tee complete all as specified and directed.

M&L for preparation of old cement conctere tiles surface and applying two coats of weather proof paint on floors with ready mixed paint, for use on floors over a coat of primer complete all as specified and directed.

M & L for granite 18-20mm (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms shall be moulded and like incl and over 20mm cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade complete, all as specified and directed.

Cutting channels, grooves or rebates n exc 15cm girth, and trimming surface in brick masonry or cencrete works with or without reinforcement complete all as specified and directed.

M&L for cement concrete 1:2:4 in roof kerbs or mud stops, rounded or chamfered on edges Type B0 1:2:4 (using 40mm graded stone aggregate) complete all as specified and directed.

S&F Anodised aluminium snap grid frame work 605 x 605mm for false ceiling complete all as specified and directed.

S&F 12mm thick Perforated particle board/ tiles for insula-tion and accoustic purposes, 60cm x 60cm in size, fixed with nails to timber frame work or with staples on snap grid complete all as specified and directed.

PROVISION OF COVERED SHED FOR OFFICE PURPOSE IN ICTG BLDG NO. P-226 AT R&DE (E) DIGHI PUNE (E&M PORTION). S&F LED efficient LED recessed mounting fitting 2' X 2' luminaire to enhance the delight of occupents with comfortable experience through its classic design & glare free soft illumination all as specified & directed Make - Havells Cat Part No - PLANO2X2PLR36WLED857S or eqvt in Wipro/Bajaj/Crompton as approved.

M&L Point wiring complete with 1.5 sqmm single core PVC insulated and unsheathed cable 1100 volts, FRLS grade with multistranded copper conductor ISI marked drawn through heavy duty PVC casing capping fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm stranded copper conductor cable as earth continuity conductor and connected to common earth dolly including concealed modular flush boxes including modular cover plates with frame mounting for housing the switches, socket outlets etc, all as specified and directed.

(a) One light point controlled by one switch.

(b) One fan point controlled by one switch and one regulator.

(c) One 3 pin switch socket outlet point 6 Amps on independent board.

(d) One 3 pin switch socket outlet point 6 Amps on same board with other switch.

All as per item above here in before but with copper conductor cable for one 3 pin socket outlet, 15 amp independent, with cable 2.5 sqmm size complete all as specified and directed.

S & Fix modular switch 1 way 6A, 1 module complete all as specified and directed.

S & Fix modular switch1 way 16A, 1 module complete all as specified and directed.

S & Fix modular socket out let 6A 2/3 on combined 2 module complete all as specified and directed.

S & Fix modular socket out let 6A/16A-2/3 pin combined 2 module complete all as specified and directed.

S & Fix Ceiling rose surface backlite 65x50mm 3 terminals complete all as specified and directed.

M&L Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required complete all as specified and directed. (a) 2x6.0 sqmm + 1x4.0 sqmm earth wire

S & F following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, inter connections, powder painted including earthing etc. complete all as specified and directed. (But without MCB/RCCB/Isolator). (a) 8 way, Double door

S & Fix MCB single pole, 240 volts,10 KA 'C' 6 to 32 Amps, all as specified and as directed.

S & Fix MCB single pole & neutral, 240 volts, 10K 'C' 6 to 32 Amps, all as specified and as directed.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete all as specified and directed.

vishalconstruction

M/S SANDEEP CONSTRUCTION COMPANY

AJINKYA VIKRAM GAIKWAD