SPL REPAIR TO TOILET BLOCKS IN OR LINES UNDER GE EAST MATHURA.

Amount

Demolition of reinforced concrete (cutting reinforcement as required to facilitate demolition of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work including removing rubbish off the premises complete all as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thick, including removing rubbish off the premises complete all as directed.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified.

Taking down cement plaster of any description including racking out joints, hacking for key, scrubbing down with water etc complete.

Taking down chowkats or frames with shutters (without taking off shutter from the frames ) not exceeding 1.5 Sqm each.

Taking down chowkats or frames with shutters (without taking off shutter from the frames ) exceeding 1.5 Sqm each but n.exc. 4 sqm each.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar.

M&L for Brickwork with old size fly ash bricks, straight or curved on plan exc 6m mean radius, half brick thick wall built in cement mortar 1:4 complete all as specified.

M&L for Brickwork with old size fly ash bricks, straight or curved on plan exc 6m mean radius, in half brick thick built in cement mortar 1:4 complete all as specified.

M&L rendering 15 mm thick (10mm + 5mm) plaster on brick/concrete surface in CM 1:4 and surface finished even and fair by mixing liquid water proofing compound as per manufacturers instructions complete. Note :- Liquid WPC shall be measured & paid seprately under relevant item of this BOQ.

M&L rendering 15 mm thick on other than fair faces of brick surfaces or concrete surfaces and finished surfaces even & fair in CM 1:6 all as specified.

M&L for rendering 10 mm thick on ceiling surfaces in cement mortar 1:3 finished even & fair all as specified and directed.

Supply only liquid water proofing compound hydroseal-W+ /Dr Fixit or eqivalent (for plaster hardening, to contol efflorescence & fungal growth) as approved by GE.

M&L for use & waste of steel form work (Rough finished flat) to side and soffits of floor or roof beams, lintels, contilevers sheves including supports etc complete all as specified.

M&L for use & waste of steel form work (Rough finished flat) to chajjas, chullah hoods, troughs and similar items including edges complete all as specified.

M&L for use & waste of steel form work (rough finished flat) to sides and soffit of roof slab, shelves etc complete all as specified and as directed

M&L for form work to edges of concrete flat, roof slabs not exceeding 200 mm thick shelves etc for rough finished surfaces..

M&L for 10 mm dia & over TMT bars cut to length bent to shape required incl cranking bending ,spirally for hooping for column ,hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia all as specified.

M&L for 6 to 8 mm dia TMT bars cut to length bent to shape required incl cranking bending ,spirally for hooping for column ,hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia all as specified.

All as per item No. 19 above but 5 mm dia and over upto and including 10 mm dia in stirrups spacers and binders.

M&L for RCC M-25 (Design mix) as in chajjas etc complete.

M&L for RCC M-25 grade (Design mix) as in Beams, cantilevers, bressummers, lintels & similar RCC works all as specified and directed.

M&L for RCC M-25 (Design mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M&L for Non skid Ceramic colour tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exceeding o.11 sqm but not exceeding 0.18 sqm ,in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM 1:4 all as specified and as directed.

M&L for providing glazed ceramic tiles on vertical surface 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 15mm thick rendering as in backing coat in cement mortal 1:4 complete all as specified.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube as per specification & drawings in SSR Part II of 2020.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for style and plain colour PVC sheets for top rail & bottom rail Paneling plain colour PVC sheet to be fitted in MS frame welded/sealed to the stile & rails with suitable PVC sheet beading as per specification & shown on drawing in SSR Pt II of 2020 incl tower bolt Aluminum 150mm – 2 Nos , hinges stainless steel 100 mm size – 3 Nos , handle aluminium 125 mm – 2 Nos for each shutter complete all as specified.

S&F 125x60 mm Pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete, as specified, supplied and fixed all as specified and as directed.

M&L for PCC M-10 grade (Nominal mix) using 12.50 mm graded stone aggregate for filling in pressed steel door frames all as directed.

S&F 40 mm thick, Flush shutters, solid core construction, with block board core and plywood face panels, commercial type both face covered with decorative face veneer with lipping/frame to match on both sides complete as specified.

S&F 30mm thick, glazed and skelton shutters of IInd class hard wood, open rebated and prepared to receive glass/ gauze etc edges or framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc complete all as specified.

M&L for powder coated (power coating shall not be less than 50 microns of approved colour) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified .

M&L for powder coated (powder coating shall not be less than 50 microns of approved colour) aluminium window and ventilators shutters side hung type without sash bar , aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, peg stays 150mm long (1No), hinges type B-21, 100mm long (2Nos), handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified. Note:- Glazing shall be measured & paid separately.

S&F 4mm thick Sheet glass, ordinary quality and glazing in square exc 0.5 sq. m in each pane fixed with window shuttter complete all as specified.

S&F 4 mm thick Figured glass, pin head type and glazing in squares n exc 0.5 sq. m in each pane fixed with ventilator shuttter complete all as specified.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

S&F 100mm Butt hinges, heavy weight, cold rolled mild steel.

S&F 150mm long Aluminium, anodised, barrel tower bolts of extruded section.

S&F 150mm long Aluminium handles, cast type, anodised.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm including including 15 mm Pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure complete all as specified and as directed.

M&L for 20mm thick granite jet black colour (table rubbed and polished) in steps jambs,window cills, cooking platform and like over & including screed bed 20mm thick in CM 1:4 for laying floor & pointing in white cement 1:2 using marbal dust with admixture of pigment to match the colour including rounded/ half rounded edge and hole for gas pipe in pre-cast slab complete all as specified and as directed.

S&F in repair Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including setting the trap and pan in concrete and including 10 ltr capacity PVC valveless syphonic action type low level flushing cistern and 32mm dia PVC Flush pipe complete including jointing to socket of flushing rim all as specified and as directed.

S&F in repair Vitreous China Urinal, Half stall type, white with accessorise including CP urinal spreader for fixing with 15 mm dia pipe complete all as specified.

S&F 32 mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/ cm2 fixed complete to walls for WHB/ Urinal waste pipes.

Dismantling water tanks exc 500 ltrs and n exc 1000 ltrs taking down complete all as specified and as directed.

Supply and fix 1000 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc complete.

S&F 20 mm dia Ball brass valve high pressure with polythene float and fly nuts complete screwed for iron pipes or brass ferrule and fixed.

M&L for Cutting chases pinning in , making good to facing where reqd. and pointing in CM 1:3 to ends or edges of landing , steps, cills, sunshades,selfs lintels etc. and cutting chases for conceled for water tubing or conceled condute wiring etc and making good, cutting n.exc 10cm girth.complete all as specified & as directed

S&F 25 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed

Taking up or down 15 mm bore of dia steel tubing and connections, including cleaning for refixing or removal to store.

Taking up or down 25 mm bore of dia steel tubing and connections, including cleaning for refixing or removal to store.

Supplying & fixing to walls and ceiling 25 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed

Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed

S&F in repair 15 mm bore fancy type Chromium plated Angle stop valve cast copper alloy screwed one ends to iron pipe or for unions and other end to PVC connection all as specified

S&F in repair 15 mm bore fancy type Chromium plated Stop cock (concealed type) cast copper alloy screwed both ends to iron pipe.all as specified.

S&F in repair 15 mm bore bib taps long body fancy type cast copper alloy crutch or butter fly handle screwed doen screwed for iron pipe.

S&F CP chromium plated brass pillar cock suitable for counter top WHB. Make :- Cat Part No OPP-15001PM of Jaquar or equivalent make given under list of makes.

S&F Brass Chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union.

S&F 75 mm dia PVC (SWR) floor trap with CP grating including jointing with solvent cement all as specified.

S&F PVC (SWR) gully trap 125/110 mm,setting and jointing with solvent cement all as specified.

S&F in repair 75mm PVC (SWR) pipes type 'A' single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F in repair 75mm PVC (SWR) pipes type 'A' single socketed, in any length with rubber ring joints, fixed to walls all as specified and as directed.

S&F in repair 110mm bore PVC (SWR) pipes type 'A' single socketed, excluding fittings in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F in repair 110mm bore PVC (SWR) pipes type 'A' single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed.

S&F 110 mm dia PVC (SWR) bends any radius all as specified as directed.

S&F 110mm bore PVC (SWR) junction single, (Single T) with access door all as specified and as directed.

S&F 75mm bore PVC (SWR) bends any radius all as specified and as directed.

S&F 110mm bore PVC (SWR) vent cowl all as specified and as directed.

M&L PVC connections 15mm size with PTMT nuts of length 450 mm complete.

Dismantling brick/ cement concrete tiles any size etc incl existing roof treatment of any thickness.

M&L for 25 mm average thick PCC M-15 grade (Nominal mix) (using 12.5 mm grade stone aggregate) in floors/padding finishing the surface even and smooth with out using extra cement.

M&L APP based polymeric membrane not less than 3 mm thick, weighing not less then 3.5 kg / Sqm, reinforeced with polyster non-woven fabric (weighing not less than 150 gm/sqm) and upper side of membrane thermally insulated with white mineral gravel finish, uniformly embeded during manufacturing process, shall be used. It shall be laid by torch application. Side overlaps shall be 75 mm and the ends shall be 100 mm and all overlaps and jointed shall also be sealed by torch application. For parapets, membrane shall be taken to a height of minimum 30cm and then inserted inside the parapet in a grooves.The same shall be finished by a membrane flashing over a coat of cold applied bituminous primer confiming to IS:3384. @ 0.40kg per Sqm complete all as specified and directed.

M &L for Cement concrete tiles 25cm x 25cm x 22mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished over and including 20 mm screed bedding layer in CM 1:4 complete with white cement and pigment complete all as specified and directed.

M & L for 50mm thick in PCC M-10 grade (Nominal mix) as in plinth protection surface finished even and smooth without using extra cement all as specified.

M&L for preparation of newly plastered surface of walls and applying two coat of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for preparing newly plastered surface of wall and applying three coats of white wash including prepration of wall complete all as specified.

M&L for preparing newly plastered surface of ceiling and applying three coats of white wash including prepration of ceiling complete all as specified.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth, for foundation etc or for shafts, wells cessipts, manholes, pier holes, sewage line, laying cables etc and getting out in soft/loose soil.

M&L 100 mm thick cement concrete M-7.5 grade (Nominal mix) using 40mm graded stone aggregate as in sub base all as specified and as directed.

M&L for 25 mm thick Sand filling under floors including consolidation for laying paver block complete.

M&L for Machine pressed precast concrete interlocking paver block(with grey cement and pigment) any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade complete all as specified by Engr-in-charge.

M&L for PCC M-10 grade (Nominal mix) using 20mm graded stone aggregate as in bed to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested for 100mm bore all as specified.

M&L salt glazed stone ware drain pipe 150 mm bore grade 'A' laid in trenches and jointed with CM 1:1 complete all as specified

M&L PCC M-15 grade (Nominal mix) using 20mm graded stone aggregate as in coping etc. complete all as specified and directed.

Returning filling in soil including spreading levelling watering and well ramming in layers not exc 25 mm thick complete.

Spreading and levelling excavated earth in layers n exc. 25 cm thick and well ramming including watering as required below flooring.

Removing excavated material to a distance n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed

Taking down aluminium/copper point wiring (light, fan, socket or power) complete, such as switches, ceiling roses, pendent, regulators, sockets etc, removing materials to store for keeping in safe custody or for taking credit and making good to the disturbed surfaces of walls, ceilings and floors etc complete all as directed.

Taking out existing copper/aluminium sub main wiring of any size and making good the disturbed surfaces complete all as specified and directed

Material and labour for point wiring with 1.5 sq mm PVC insulated unsheathed single core multi-stranded copper conductor cable 1100 Volts grade (FRLS), drawn through and including 20 mm dia rigid non-metallic PVC concealed conduit (medium grade) along with 1.5 sq mm continuous PVC insulated unsheathed solid/stranded copper conductor cable for earth continuity wire, connected to earth dolly and to be terminated in modular flush metal boxes and suitable for modular fittings, concealed type, covered with modular plates for mounting modular switches, sockets, regulators etc including,cutting chasing and testing on completion complete all as specified and as directed by the Engineer-in-Charge for the followings:-

One light point controlled by one switch

One exhaust fan point controlled by one switch

All as per item No 94 here-in-above but for one 15 Amp 3 pin / 6 pin switch socket outlet, independent, with 2.5 sq mm single core multi-stranded copper conductor along with 2.5 sq mm continuous PVC insulated unsheathed solid copper conductor cable for earth continuity wire, all as specified .

S & F switch modular type 6 Amps 1 module all as specified

S&F switch modular type, single pole one module 16 Amps 230v

S&F socket modular type 2-in-1, 5 Pin, 6/16 Amps 2 module.

Supply and Fixing ceiling rose surface bakelite 65mm x 50mm three terminals complete all as specified.

Supply and fixing LED lights fitting 1x 20W, 220V AC decorative type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make Surya Cat Part No SLE BT 20 IL or equvalent make given under list of makes.

Supply and fixing LED lights fitting 1x 9W, 220V AC decorative type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make Surya Cat Part No SLE BT 10 or equvalent make given under list of makes.

S&F environmental friendly, ultra modern, energy saving, surface mounted, Bulk Head fitting of 10 Watt complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of complete all as specified and as directed. Make :- Surya Cat Part No SLE BH 10w or equivalent make in philips/Havells.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed incl depositing the old one in MES store yard complete.

M&L for submain wiring with two runs of FRLS single core 4 sqmm for main wire and one run of single core 4 sqmm as earth wire of stranded copper conductor FRLS PVC insulated unsheathed cables conforming to IS : 694 drawn through and including concealed in wall rigid medium duty unplasticised PVC conduit conforming to IS : 9537 ( Part-3) and ISI marked not less than 20 mm dia and accessorie all conforming to IS specification complete. Note :- Two runs of 4 Sqmm single core cable, one run of 4 Sqmm earth wire & One run of PVC conduit shall be measured as one unit length.

S & F factory made epoxy powder coated Distribution Board SPN 4 ways ( SPN MCB DB ) with metal door ( IP-43 protection ) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removeable gland plates with Knockouts complete all as specified

S&F Single pole and neutral (SPN) MCB 40 Amps, 240 V, 50Hz, 10KA breaking capacity complete.

S&F Single pole (SP) MCB 6-40 Amps, 240 V, 50Hz,10KA breaking capacity all as specified.

S&F in replacement of building street light fitting, IP66 powder coated pressure die cast aluminium with heat resistant toughened glass complete of 36 Watt capacity including fixing arrangement complete with all accessories including connecting up with twin core copper conductor cable with suitable size all as directed. Make : Surya Cat Part No SLE UL 36W IP66 (LXN) or equivalent makes given under list of makes.

S&F GI Pipe brackets made out of 40 mm dia GI pipe, medium grade, 1.5 mtr length, bent to shape , fixed with two Nos 50 x 6 mm size flat mild steel clamps made to shape and size and suitable nuts bolts and washers etc compete all as specified and directed by Engineer-in-Charge.

Supply and fix electric water heater storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate NRV, connection pipe etc. incl depositing the old one in MES store yard complete.

Supply and fixing LT XLPE insulated heavy duty electric cables with aluminium condudctor, 1100 volts grade, 16 Sqmm 4 core complete all as specified

Supply and fixing LT XLPE insulated heavy duty electric cables with aluminium condudctor, 1100 volts grade, 10 Sqmm 2 core complete all as specified

M&L for sand cushioning to under ground cable in trenches in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as specified and directed by Engr in charge. Note:- Measurement shall be taken after gentling puning of sand.

M&L for laying in trenches un-reinforced precast cement concrete cable cover, class LV type 1, flat, size 250mmx150mmx40mm for cable protection laid adjacent to each other length wise perpendicular to the central axis of cable complete all as specified.

M&L for fabrication of cubical LT panel board outdoor type with double door made out of 3.15 mm thick MS sheet, dust, vermin and water proof duly supported on 40 x 40 x 6 mm angle iron frame, having locking arrangement at front and opening arrangement from front & rear both duly fitted with compression cable glands for entry & exit of cables, powder coated with two coats and having minimun clearance of 450 mm above ground level complete comprising of the following :-(a)Panel mounted Multi-function for voltage, current, frequency, power factor and power Type EM-VIFP -01 set. (b) Al bus bar --- 03 Nos. For phase of capacity 200 Amp and 1 Nos 200 Amps for neutral, duly taped in colour coded FRP sleeves. (c) Indicating lamps Red, Yellow and blue in colour, LED type complete with lamp holders, 220 volts AC.- 01 Set of 3 (d) Panel wiring with 2.5 Sqmm PVC Sheathed, PVC insulated FR-HR stranded copper conductor cable through MCB DP 10 A mounted on DIN rail. (e) 4 Pole TPN 63 Amp , 415 V , 16 KA - 01 Nos (f) SPN MCB 40 Amp - 4 Nos

S&F GI pipe Light grade 40 mm dia Complete all as specified

Material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete.

BHARDWAJ CONSTRUCTIONS

M/S YATENDRA SINGH

shyam construction

Ms Kamal Kant Agarwal

Sham Sunder Bansal

ARCHI ENGINEERS