TWW Micro Irrigation at NNL District MGarh, by providing and laying DI HDPE pipe line, including construction of TWW balancing reservoir, PH, pumping machinery, (Electro Mechanical components) including running maintenance for a period of 03 years al

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge. All kinds of soil (HSR 4.12.1)

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm. Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth up to 1.5 metre). (HSR 4.16.1.3+4.17)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :450 mm dia. R.C.C. pipe. (HSR 22.168.5)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size). (HSR 6.14.2)

Brick Massonary work in cement motar 1:3 in foundation complete excluding pointing and plastering (HSR item No. 15.16.1)

Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. All works up to Plinth Level : M-15 grade plain cement concrete. (cement content considered @ 240 kg/cum). (HSR 6.22.2.2)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works up to plinth level. Extra for providing richer mixes up to plinth and at all floor levels. Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum). (HSR 6.25.1+6.26.1)

Reinforced cement concrete work in beams, suspended floors,roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). (HSR 6.16)

Brick work with common burnt clay non-modular bricks of class designation 7.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand). (HSR 7.22.1)

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending,placing in position, binding, wastage, overlaps, welded joints,spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level. Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually usedin work , excluding overlaps. Wastage, overlaps, couplings,welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. Cold twisted bars. (HSR 6.33.3)

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies (HSR 6.30.3)

Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. (HSR 6.30.2)

15 mm cement plaster on the rough side of single or half brick wall of mix.1:4 (1 cement: 4 fine sand) (HSR 11.6.1)

12 mm cement plaster of mix : (IN FINE SAND) (HSR 11.5.4)

10 mm cement plaster of mix : (IN FINE SAND) (HSR 11.4.2)

Designing, providing, installing and fixing factory finished custom designed cold form Light Gauge Steel Framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. The steel sheet shall be galvanized (AZ-150gms Aluminium Zinc Alloy coated steel having minimum yield strength 300-550 Mpa) conforming to AISI specifications and IBC 2009 for cold formed steel framing and construction and also as per IS: 875-1987, ISO 800-1984 and IS:801- 1975. The wind load shall be as per provisions of IS 875 (part -III). LGSFS frame shall be designed as per IS: 801 using commercially available software such as Frame CAD Pro-11.7/ STAAD PROV8i/ ArchitekV2.5.16/ Rivet architecture-2011 or equivalent. Proper usage of Connection Accessories like Heavy Duty Tension Ties, Light Duty Hold-ons, Twist Straps (to connect truss with wall frames), Strong Tie, Tie Rod, H-Brackets, Boxing Sections, LShaped Angles for better structural stability. The framing section shall be cold form Ctype having minimum web depth 89 mm x 39mm flange x 1mm lip in required length as per structural design requirement. (HSR 32.9)

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover. (HSR 13.37.1)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. (HSR 13.28)

Providing & fixing steel bar embedded plastic steps of size 263mm x 165mm of orange colour, confirming to specification in pump chambers, manholes etc., having minimum 3mm thick polypropylene polymer confirming to is:10910 encapsulated on 12mm dia ribbed steel bars per IS :1786. The rate include cost of setting the same to correct lines and levels duly embedded in 1:2:4 cement concrete including carriage, loading, uploading, stacking, handling, re-handling etc., complete in all respect to the satisfaction of Engineer-in-charge. (HSR 21.28)

Providing and laying of base course of floors consisting of 100 mm thick cement 1:8:16 and 100 mm sand or stone filling. (HSR 10.1)

Providing and fixing of Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick. (HSR 10.37.1)

Supply and erection of 10.5 cm dia M.S.Fan box including 8 mm dia 30 cm long M.S. Road made into suitable suspension hook and erected in R.C.C. slab for the erection of fan complete with all labour and material required to complete the job. (HSR 23.8.4)

Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe.Group A (HSR item No. 23.4.1.1)

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 4 way ( 2 incoming and 2 outgoing)(HSR No.23.22.4.1)

Providing and fixing Modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Switch 5 amp. 1 way switch. (HSR 23.8.11.1)

Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , includingproviding 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 AmpModular type switch required GI Box ,modular face plate etc complete as required. Group A(HSR No. 23.4.4.1)

Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling ,including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box, Modular face plate etc complete as required. Group A(HSR No. 23.4.5.1)

Providing and fixing Piano type accessories of approved make in existing box and sheet including fixing and making necessary connections, complete in all respect. Bakelite angle/straight button holder large size. (HSR 23.8.1.12)

Providing and fixing Modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Step type Fan Regulator 2 modules 300watt.(HSR 23.8.11.7)

Supply and Fixing 3 mm thick Bakelite sheet cover on existing MS/PVC junction box/tee etc including fixing with brass screws and washers. (HSR 23.8.12)

Supply and erection of suitable MS/GI Box covered with 5 mm thick Bakelite sheet as below. 180 mm X 100 mm X 60 mm deep M.S. Box (HSR 23.8.3.3)

Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole. (HSR 23.22.5.1)

Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. (HSR NO. 23.7.6.1)

Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete. (HSR 11.58)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer (HSR 11.67.1)

Distempering with dry distemper of approved brand and manufacture (one or more coats) and of required shade on old work to give an even shade. (HSR 30.24)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). (HSR 11.96.1)

Dressing bed and preparation of sub grade for lining by mechanical/ mannual means. (HSR 14.1)

Dressing side slopes and preparation of sub grade for lining by mechanical/ mannual means. (HSR 14.2)

Putting 1:3 Cement sand slurry, 6mm thick on prepared bed and side slopes before laying concrete on bed and side slopes. (HSR 14.13)

Extra allowance for providing templates in curved portion of lining. ((HSR 14.15)

Extra allowance for form work in concrete lining in Bed. (HSR 14.16.1)

Extra allowance for form work in concrete lining On sides slopes. (HSR 14.16.2)

Extra allowance for scaffolding, in tile and concrete lining for side slopes. (HSR 14.17)

providing and placing in horizontal layers filtering media screened washed and cleaned as described below - Broken stone, screened, washed and graded from 50 mm to 75 mm (from Ghaggar or approved equivalent quarry). (HSR 20.52.5)

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. 600mm dia RCC pipe. (HSR 22.169.2)

Providing, lowering, laying, aligning, fixing in position and jointing at all level/ depths ISi marked HDPE pipes of PE-100 grade and PN- 8 for sewer application as per IS 14333-1996 (amended up to date) in trenches in complete including cost of HDPE 'Specials, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer. Note: E/w to be measured and paid separately. Rate includes cost of all specials like bends, tees required during laying of pipe line along required alignment. 560 outside dia (HSR Item No. 21.98.10)

Providing, lowering, laying, aligning, fixing in position and jointing at all level/ depths ISi marked HDPE pipe of PE-100 grade and PN-6 for sewer. application as per IS 14333-1996 (amended up to date) in trenches in complete induding cost of HDPE Specials, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer. Note: E/w to be measured and paid separately. Rate includes cost of all specials like bends, tees required during laying of pipe line along required alignment 560 outside dia (HSR Item No. 21.97.10)

Providing, lowering, laying, aligning, fixing in position and jointing at all level/ depths ISi marked HDPE pipe of PE-80 grade and PN - 4 for sewer application as per IS 14333-1996 (amended up to date) in trenches in complete including cost of HDPE Specials, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer. Note: E/w to be measured and paid separately. Rate includes cost of all specials like bends , tees required during laying of pipe line along required alignment. 560outside dia (HSR Item No. 21.96.10)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size). (HSR 6.1.6)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size). (HSR 6.1.2)

Brick work with common burnt clay non-modular bricks of class designation 7.5 in super structure above plinth level up to floor IV level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) . (HSR 7.22.2)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone agg . (6.14.1)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete (HSR 6.30.1)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor four level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). (HSR 6.15)

Providing and laying damp-proof course with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) 40mm thick. (HSR 6.8.2)

Brick work with common burnt clay non-modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand). (HSR 7.21.1)

10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: With common burnt clay non-modular brick tile of class designation 10 (HSR 9.11.1)

Making Khurra 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone ggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, inished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. (HSR 9.18)

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter (HSR 9.57.2)

Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS :13592 Type A, including jointing with seal ring conforming to IS : 5382,leaving 10 mm gap for thermal expansion. 110 mm bend. (HSR 9.58.5.2)

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. (HSR 10.42)

Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre.(HSR 10.43)

Providing and fixing of Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. (HSR 10.38)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (HSR 11.78)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). (HSR 13.41)

Supply & fixing Windows frames (Chowkhats) including mullions consisting frame fabricated from sheet roll formed out of 1.2mm thick galvanized sheet as per IS:277 (Base steel as per IS 513) with zinc of 120 gm/sqm & Powder coated with pure Polyester powder up to 50 microns (as per approved colour) Door Frame of size 80mm x 50mm with 37mm wide single rebate for 35mm door shutter. (HSR 13.21.1)

Providing and fixing 1 mm thick M.S. sheet sliding-shutters, with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm M.S. gusset plates at the junctions and corners, 25 mm dia pulley, 40x40x6 mm angle and T- iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer. (HSR 13.36)

Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required. Extra for charcoal or coke and salt for G.I. plate or copper plate earth electrode. (HSR 24.1.3 + 24.1.5)

Supply, erection, testing of Ceiling fans IS marked (as per IS code 374) with suitable GI pipe complete in all respects complete as per directions of Engineer-in-charge. (48" or 1200 mm) ceiling Fan. (HSR 20.71.1)

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia. (HSR 4.16.1.2)

Providing laying fixing and jointing of ISI marked HDPE pipes as per ISI 4984-1995 casting along the trenches to correct alignment and gradients, cutting, jointing and testing complete as per specifications (CSR 28.15 D (h)) 160mm dia

Providing & fixing cast iron double flanged swing check type reflux (non return) valves PN-1.6 marked with IS:5312 including nuts & bolts marked with IS:1363, rubber sheet marked with IS:638 etc., carriage loading, unloading, stacking, handling, re-handling etc. Complete in all respect to the satisfaction of Engineer-in-charge (HSR 20.11.10) 500mm

Providing, lowering, laying, aligning, fixing in position and jointing at all level/depths ISI marked HDPE pipe of PE-100 grade and PN-6 for sewer application as per IS 14333-1996 (amended up to date) in trenches in complete including cost of HDPE Specials, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer. Note: E/w to be measured and paid separately. Rate includes cost of all specials like bends, tees required during laying of pipe line along required alignment..225 mm Outside Dia. (HSR 21.97.2)

Providing, lowering, laying, aligning, fixing in position and jointing at all level/depths ISI marked HDPE pipe of PE-100 grade and PN-6 for sewer application as per IS 14333-1996 (amended up to date) in trenches in complete including cost of HDPE Specials, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer. Note: E/w to be measured and paid separately. Rate includes cost of all specials like bends, tees required during laying of pipe line along required alignment..250 mm Outside Dia. (HSR 21.97.3)

Providing & fixing cast iron double flanged swing check type reflux (non return) valves PN-1.6 marked with IS:5312 including nuts & bolts marked with IS:1363, rubber sheet marked with IS:638 etc., carriage loading, unloading, stacking, handling, re-handling etc. Complete in all respect to the satisfaction of Engineer-in-charge(HSR 20.11.6) 300mm

Providing & fixing cast iron double flanged swing check type reflux (non return) valves PN-1.6 marked with IS:5312 including nuts & bolts marked with IS:1363, rubber sheet marked with IS:638 etc., carriage loading, unloading, stacking, handling, re-handling etc. Complete in all respect to the satisfaction of Engineer-in-charge(HSR 20.11.5) 250mm

Providing & fixing cast iron double flanged swing check type reflux (non return) valves PN-1.6 marked with IS:5312 including nuts & bolts marked with IS:1363, rubber sheet marked with IS:638 etc., carriage loading, unloading, stacking, handling, re-handling etc. Complete in all respect to the satisfaction of Engineer-in-charge(HSR 20.11.4) 200mm

G.I Barbed Wire Fencing 1.2 Metre High :Providing and fixing 1.2 metres high GI barbed wire fencing with 1.8 m angle iron posts 40 mm x 40 mm x 6 mm placed every 3 metres centre to centre founded in M15 grade cement concrete, 0.6 metre below ground level, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with 9 horizontal lines and 2 diagonals interwoven with horizontal wires, fixed with GI staples, turn buckles etc complete as per clause 807. (HSR 34.29.1)

Providing and laying Double Flanged (screwed / welded) Centrifugally (Spun) Cast Iron, Class B (IS : 1536) :300 mm dia C.I. Double Flanged Pipe. (HSR 22.159.5)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level:1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size) (HSR 6.1.4)

Brick work with common burnt clay non-modular bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)(HSR 7.21.2)

12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) (HSR 11.5.3)

Supplying, errection, testing of Exhaust fan (as per IS code 374) having a capacity of 45 cubic metre per minute complete with suitable G.I sheet ducting in structure confirming to latest IS specifications complete in all respect to satisfaction of Engineer-in-charge.(HSR 20.72)

Providing and laying 80mm thick factory made cement concrete interlocking paver block of M -35 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over (BIS 15658:2006) and including 60mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.(HSR 10.77)

Providing and laying Double Flanged (screwed / welded) Centrifugally (Spun) Cast Iron, Class B (IS : 1536) :200 mm dia C.I. Double Flanged Pipe. (HSR 22.159.3)

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :200 mm diameter Class I(HSR 22.162.4.1)

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :300 mm diameter Class I(HSR 22.162.6.1)

Providing and laying flanged C.I. standard specials such as tees, bends, collars, tapers, caps etc., suitable for flanged jointing as per IS : 1538 :Up to 300 mm dia (HSR 22.151.1)

Providing & fixing cast iron single air valves marked with IS:14845 including carriage, loading, uploading stacking, handling, re-handling etc. drilling, tapping, screwing etc. in valves connections complete in all respects to the satisfaction of Engineer-in-charge. (Rate is same for 40mm/50mm i/d pipes)50 mm i/d (HSR 20.13.2)

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :100 mm diameter Class I(HSR 22.162.1.1)

Providing, lowering, laying, aligning, fixing in position and jointing at all level/depths ISI marked HDPE pipe of PE-100 grade and PN-6 for sewer application as per IS 14333-1996 (amended up to date) in trenches in complete including cost of HDPE Specials, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer. Note: E/w to be measured and paid separately. Rate includes cost of all specials like bends, tees required during laying of pipe line along required alignment.280 mm Outside Dia. (HSR 21.97.4)

Providing, lowering, laying, aligning, fixing in position and jointing at all level/depths ISI marked HDPE pipe of PE-100 grade and PN-6 for sewer application as per IS 14333-1996 (amended up to date) in trenches in complete including cost of HDPE Specials, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer. Note: E/w to be measured and paid separately. Rate includes cost of all specials like bends, tees required during laying of pipe line along required alignment.315 mm Outside Dia. (HSR 21.97.5)

Supply and installation of 50mm i/d hydraulic pressure relief valve of polemeride with accessories for pressure regulation of irrigation system as per B IS standard.

Supply and fixing of Gantry with chain pulley block (tested for 1.5 times therated capacity) with travelling trolley of appropriate lifting capacity as per IS code 3177:1999 with up to date amendments for handling of pumping sets capable of moving along the girders including cost of suitable sized RCC pillars to be provided in pump house complete in all respects as per directions of Engineer-in-charge(1.5 tonne capacity) (HSR 20.73.2)

Design, Supply & erection of transformer of standard make Required 25 KVA 11/0.433 KVA rating outdoor type 11 KVA V.C.B, panel, G.O. switch, H. Pole , H.T metering panel, APFC panel, battery charges, 11 KVA substation, entire cable network from G.O. switch to H.T metering equipment and from H.T metering to Transformer. From transformer to main to L.T, panel earthling, safety equipment, fenced enclosure for transformer, and any other contingent thereto complete in all respect as per approved make and directions of Engineer-in-charge as per respective capacity. (HSR 20.76.14) 700KVA

Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :150 to 185 sqmm (HSR 24.3.3.2)Indoor

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:150 to 185 sqmm (HSR 24.3.4.2)Outdoor

Supply and erection of XLPE (E)11 KV HT aluminum conductor armoured cable ISI mark laid in existing pipe /tranches/surface with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-Charge of the work. 50 sqmm 3 core XLPE Cable. ( OLD HSR No. 31.71 (ii))

Supply, erection, testing & commissioning of G.O. Switch two poles, with blade, pin 6 insulators operating handle with GI pipe 25 mm class B complete in all respects. (HSR 20.86)

Supply, erection, testing and commissioning of CT meter of standard make with cubical meter box as per HVPNL specifications including 3 phase electrical meter 100/5 of standard make approved by HVPNL including CT/PT of suitable rating complete in all respect as per directions of Engineer-in-charge(HSR 20.88)

Erection of RCC/ PCC pole of following length in brick ballast and ramming the foundation, finishing with 150mm thick cement concrete (1:3:6) layer on top with including excavation and refilling etc as required.Above 6 metre and up to 8.0 metre(HSR 24.4.10.3)

Supply and erection of XLPE (E)11 KV HT aluminum conductor armoured cable ISI mark laid in existing pipe /tranches/surface with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-Charge of the work. 70 sqmm 3 core XLPE Cable. ( OLD HSR No. 31.71 (iii))

Supplying and fixing of Automatic DI Air valve single chamber type on DI Rising main consisting two Orifice venting system with 3 functions (Supply and release of air as well as automatic venting during operation) of IVC/VAG make as conforming to IS 14865 as amended upto date with ISI mark incluidng drilling, taping, screwing with 150 mm i/d D.I. pipe upto height of 3.00 mtr. within casing/cover of RCC Coluumn of size 200 mm x 200 mm including construction of RCC Plateform including all required T&P, supply & fixing of D.I. specials & sluice valve complete in all respect specification as described in Schedule No. II. (Rate already approved in the estiamte of raw water arrangement for proposed Multimodel Logistic Hub at Narnaul, sanctioned vide worthy EIC, IWRD letter No.- 1833/5LCU/521/2021/Vol-II, Dated: 02-04-2021.)

Supply erection testing and commissioning of Pressure gauge with glistening immersed complete in all respect with all fittings etc. (Rate already approved in the estiamte of raw water arrangement for proposed Multimodel Logistic Hub at Narnaul, sanctioned vide worthy EIC, IWRD letter No.- 1833/5LCU/521/2021/Vol-II, Dated: 02-04-2021.)

Supply, erection, testing of single core copper wire with ISI marked for making connection with LT Panel Board to electric motor and other electric appliances with underground system in PVC/flexible pipes/ Cable tray with all required accessories like thimble etc. as directed by Engineer-in-Charge complete in all respect specification as described in Schedule No. II(i) 95 Sq. mm single core copper wire. (Rate already approved in the estiamte of raw water arrangement for proposed Multimodel Logistic Hub at Narnaul, sanctioned vide worthy EIC, IWRD letter No.- 1833/5LCU/521/2021/Vol-II, Dated: 02-04-2021.)

Supply erection, testing & commissioning of Vacuum Ciruit Breaker (VCB) for 11 KV HT Panel having degree of protection not less than IP-42, indoor, metal clad, free floor standing vertical cubicle, deadfront, removal, back cover, facricated with CRCA sheet suitable for 11 KV, 400 A, 3 Phase, 50 Hz, 350 MVA repturing capacity Vacuum Ciruit Breaker (VCBs), Horizontal draw out type spring charger mechanism, 110 V AC Triping coils, indicating lamps, anti pumping contactor, standard multi core terminals, standard wiring and earthing arrangement push buttons, standard paint electrolytic copper busbar mechanical interlocking arrangement indication arrangement closed/ open, spring, charges/ discharged as well as DC trip history tripped/ healthy, cable boxed and all standard fitting & accessories complete in all respect specification as described in Schedule No. II. (Including third party inspection from CEIL) (Rate already approved in the estiamte of raw water arrangement for proposed Multimodel Logistic Hub at Narnaul, sanctioned vide worthy EIC, IWRD letter No.- 1833/5LCU/521/2021/Vol-II, Dated: 02-04-2021.)

Providing, installing, testing, and commisioning of vertical Turbine pumps having discharge of 578 cum /hr at 45 mtr head with anti- friction, thrust bearing, column pipes, including motors 170HP suitable for treated waste water having discharge 5.67 Cs, stool, strainer etc. including carriage, loading, unloading, painting etc. complete in all respects (Make : Kirloskar/ Mather & Platt/ WPIL/ Jyoti/ KSB(Including third party inspection from Govt. Agency) suitable for Treated waste water. Note: The pump & motor should be suitable for treated waste water. (Rate already approved in the estimate of Extension of Nimbhera Minor from Km. 0.00 to 20.880)

Supply & erection of Horizontal centrifugal spilt casing type pumps conforming to all respect IS 1520-1972 of following duties directly coupled to AC squirrel cage induction type electric motor conforming to IS 325-1978 with accessories complete in all respect (the make shall be of Kirloskar, Crompton, ABB, Siemens, NGFE/ GEC)(Including third party inspection from Govt. Agency)suitable for Treated waste water discharge of 205 cum /hr at 50 mtr head with 50 HP motor having discharge 2.0 Cs. Note: The pump & motor should be suitable for treated waste water. (Rate already approved vide worthy EIC, IWRD, Pkl letter no.- 296/NABARD/2021, Dated: 19/02/2021.

Supply & erection of Horizontal centrifugal spilt casing type pumps conforming to all respect IS 1520-1972 of following duties directly coupled to AC squirrel cage induction type electric motor conforming to IS 325-1978 with accessories complete in all respect (the make shall be of Kirloskar, Crompton, ABB, Siemens, NGFE/ GEC)(Including third party inspection from Govt. Agency)suitable for Treated waste water discharge of 171 cum /hr at 50 mtr head with 50 HP motor having discharge 1.67 Cs. Note: The pump & motor should be suitable for treated waste water.

Supply erection, testing & commisioning of equipment on HT metering panel 11 KV consisting of one no G.O switch, one No. Electric Trivector meter 3 phase 4 wire 0.5 class of accuracy on KW hour point Basis complete with HT CTs of 50/5 amp /110 VA burden and class of 0.5 accuracy and H.T.PT 11 KV - 50/5 Amp./ 110V burden and class of 0.5 accuracy including metering panel with complete accessories in all respects specification as described in Schedule No. II. (Rate already approved in the estiamte of raw water arrangement for proposed Multimodel Logistic Hub at Narnaul, sanctioned vide worthy EIC, IWRD letter No.- 1833/5LCU/521/2021/Vol-II, Dated: 02-04-2021.)

Design, supply, installation, testing & commissioning of cubical type L.T. panel suitable for 415 Volt, 3 phase, 4 wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel of 16 SWG thick for frame work & covers, 3 mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for approved shades, having 800 Amp. Capacity extensible type TPN Aluminium Alloy Bus bar for high conductivity, DMC/SMC bus bar supports, Panel Manufacturer shall have CPRI test certificate for short circuit with stand capacity of 31 MVA for 1 Sec. bottom based channel of MS section not less than 100 mm x 50 mm x 5 mm thick of 1 feet height from floor level, entire panel shall have a common tinned copper earth bar of size 25 mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of copper bus bar and control wiring with 2.5 sq. mm FRLS insulated copper conductor S/C Cable, Cable alleys, Cable gland plates in two half, i/c providing following switch gears etc. as required. Including separate 2 No. chemical earthing as per specification approved by technical committee and including supply & fixing of 6 No. Bimetallic clamp with nut & bolt , washers for LT cable connection of size 3.5 x 400 square mm as per specification. The design and drawing of panel board will be approved from Engineer-in-Charge before installation at site. For running of pump set through ATS starters of suitable capacity as per pump capacity (1 No. Pump + 1 No. Pump stand by) and including supply & fixing of following items : (a). Incomer : i. 1 No. 4 Pole ACB 630amp, breaking capacity 50 KA, Icu for 1 Second as per IS code Make : L&T or equivalent in ABB/Siemens/Schneider. ii. 1 Set. 3 Phase Volt Meter with SS, Amp. meter with SS including suitable size of CT digital type, RYB indicator set. Make : L&T/ABB/C&S/Schneider. iii. 1.1 KV UE 3.5 x 400 Sqmm XLPE Insulated cable, stranded compacted circular shaped aluminium conductor, overall PVC Sheathed cable confirming to IS 7098 Part-2, 2011 with latest amendments. = 150 Mtr. (Make: Havells /Polycab / Finolex) iv. 1.1 KV UE Core 3.5 x 400 Sqmm XLPE Insulated cable, stranded compacted circular shaped aluminium conductor, overall PVC Sheathed cable confirming to IS 7098 Part-2, 2011 with latest amendments. = 40 Mtr. (Make: Havells/PolyCab/Finolex) (b). Outgoing Feeder i. 3 No. TP MCCB of 400 Amps, 36KA (Ics = 100%), for connection to ATS Starter each outgoing should also have a separate enclosure with one no. TP MCCB of 400 Amps, 36KA (Ics = 100%). Make : L&T / ABB / Siemens/Schneider/BCH. ii. 2 Nos. fully automatic transformer type starter 170 HP, 3 Phase, 415 volt, 50 Hz Starter with Air cooled including contactors, phase indicator & other auxiliary protection circuit, connections and small items i.e. thimbles, nut/bolt, etc with degree of protection IP 55 with allied accessories as per make : Andrewyule/AE/BCH/Schneider/Kilburn. iii. 2 Set. 3 Phase Volt Meter with SS, Amp. meter with SS including suitable size of CT digital type, RYB indicator set. Make : L&T/ABB/C&S/Schneider. Makes of Capacitor/ contactor/ MCCB/ APFC Controller : L&T/ Siemens/ ABB/BCH/Epcos/Shreem/Unistar. iv. 3x 185 sqmm LT cable 1.1 KV 120 Mtr. LT capacitor bank for electric motor of cap. 170HP, 1440RPM , 3 phase-415 V supply of size 180 KVAR. (capacitor bank shall be designed commenly for running of 1 No. Pumps at a time of each capacity 170 HP + 1 No. Pump is Ideal as standby operation) Note : For run 1 Nos. Motors at a time the squirrel cage induction electric motor of each capacity 170 HP, to run the raw water pump having discharge578 cum/Hr with 40 mtr. Head) (Including third party inspection from govt. agency).

Supplying & fixing of C.I. Double flanged pipeline conforming to IS-7181 and amended upto date with ISI marked including cost of earth work, stringing out, layng, Jointing & testing including required jointing in position as directed by Engineer-in-Charge complete in all respect specification as described in Schedule No. II. (400mm). (Rate already approved in the estiamte of raw water arrangement for proposed Multimodel Logistic Hub at Narnaul, sanctioned vide worthy EIC, IWRD letter No.- 1833/5LCU/521/2021/Vol-II, Dated: 02-04-2021.)

Providing, installing, testing and commisioning of manually operated Double flanged DI Sluice valve PN 1.0 as per IS 14846 including cost of nut bolts, insertion sheet, carriage, loading , unloading, painting etc. (Make: IVC/ Kirloskar/ VAG / AVK /Bermad/ Dorot) 300 mm i/d(Rate already approved in the estiamte of Extension of Nimbhera Minor from Km. 0.00 to 20.880)

Providing, installing, testing and commisioning of manually operated Double flanged DI Sluice valve PN 1.0 as per IS 14846 including cost of nut bolts, insertion sheet, carriage, loading , unloading, painting etc. (Make: IVC/ Kirloskar/ VAG / AVK /Bermad/ Dorot) 400 mm i/d(Rate already approved in the estiamte of Extension of Nimbhera Minor from Km. 0.00 to 20.880)

Providing, installing, testing and commisioning of manually operated Double flanged DI Sluice valve PN 1.0 as per IS 14846 including cost of nut bolts, insertion sheet, carriage, loading , unloading, painting etc. (Make: IVC/ Kirloskar/ VAG / AVK /Bermad/ Dorot) 600 mm i/d (With byepass pressure release valves arrangement)(Rate already approved in the estimate of raw water arrangement for Logistic Hub in Narnaul)

Supplying, Installing and Testing of 75 Cu. Pipe filled with Crystalline conductive mixture with Copper Strip of size 40mm x 6mm of length 2 mtr with eco friendly backfill compound 50Kg. Makes- Genus/Ashok/GMAXX, (Rate already approved in the estiamte of Extension of Nimbhera Minor from Km. 0.00 to 20.880)

Earth pit chamber (300mm x 300mm) with CI cover for the above

Providing and fixing 50mm x 6mm copper strip in 80mm dia GI pipe FRL earth Electrode including connection with Brass nut, bolt, spring, washer, excavation and reflling etc. as required. (Rate already approved in the estiamte of Extension of Nimbhera Minor from Km. 0.00 to 20.880)

Supplying, Installing and Testing of 100mm GI Pipe filled with Crystalline conductive mixture with Copper Strip of size 40mm x 6mm of length 2 mtr with eco friendly backfill compound 50Kg. Makes- Genus/Ashok/Shree Electrodes (Rate already approved in the estiamte of Extension of Nimbhera Minor from Km. 0.00 to 20.880)

Earth pit chamber (300mm x 300mm) with CI cover for the above

Supply, transport, unloading, shifting, installation & laying of GI earth Conductor bar/flexible wire /strop of following sizes along the cable trenches or cable trays or fixing to walls or structures or below the slab, burries individually in paved/ unpaved areas including supply of earthing stripst and minor civil works finishing after laying of earthing stripts etc. The installation shall include drilling of holes, connection & crimping of adequate lugs, clamping, hardware material etc. All Hardware shall be as per the MOC of earthing strip. (Rate already approved in the estiamte of Extension of Nimbhera Minor from Km. 0.00 to 20.880) Supply, transport, unloading, shifting, installation & laying of GI earth Conductor bar/flexible wire /strop of following sizes along the cable trenches or cable trays or fixing to walls or 32 x 6 mm GI Earthing strip

Supply, transport, unloading, shifting, installation & laying of GI earth Conductor bar/flexible wire /strop of following sizes along the cable trenches or cable trays or fixing to walls or structures or below the slab, burries individually in paved/ unpaved areas including supply of earthing stripst and minor civil works finishing after laying of earthing stripts etc. The installation shall include drilling of holes, connection & crimping of adequate lugs, clamping, hardware material etc. All Hardware shall be as per the MOC of earthing strip. (Rate already approved in the estiamte of Extension of Nimbhera Minor from Km. 0.00 to 20.880) Supply, transport, unloading, shifting, installation & laying of GI earth Conductor bar/flexible wire /strop of following sizes along the cable trenches or cable trays or fixing to walls or 25 x 5 mm GI Earthing strip

Design, supply, installation, testing & commissioning of cubical type L.T. panel suitable for 415 Volt, 3 phase, 4 wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel of 16 SWG thick for frame work & covers, 3 mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for approved shades, having 400 Amp. Capacity extensible type TPN Aluminium Alloy Bus bar for high conductivity, DMC/SMC bus bar supports, Panel Manufacturer shall have CPRI test certificate for short circuit with stand capacity of 31 MVA for 1 Sec. bottom based channel of MS section not less than 100 mm x 50 mm x 5 mm thick of 1 feet height from floor level, entire panel shall have a common tinned copper earth bar of size 25 mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of copper bus bar and control wiring with 2.5 sq. mm FRLS insulated copper conductor S/C Cable, Cable alleys, Cable gland plates in two half, i/c providing following switch gears etc. as required. Including separate 2 No. chemical earthing as per specification approved by technical committee and including supply & fixing of 6 No. Bimetallic clamp with nut & bolt , washers for LT cable connection of size 3 x 185 square mm as per specification. The design and drawing of panel board will be approved from Engineer-in-Charge before installation at site. For running of pump set through ATS starters of each capacity 50 HP (3 No. Pump + 1 No. Pump stand by) and including supply & fixing of following items : (a). Incomer : i. 1 No. 4 Pole ACB 630amp, breaking capacity 50 KA, Icu for 1 Second as per IS code Make : L&T or equivalent in ABB/Siemens/Schneider. ii. 1 Set. 3 Phase Volt Meter with SS, Amp. meter with SS including suitable size of CT digital type, RYB indicator set. Make : L&T/ABB/C&S/Schneider. iii. 1.1 KV UE 3.5 X 240 Sqmm XLPE Insulated cable, stranded compacted circular shaped aluminium conductor, overall PVC Sheathed cable confirming to IS 7098 Part-2, 2011 with latest amendments. = 120 Mtr. (Make: Havells /Polycab / Finolex) iv. 1.1 KV UE 3.5 x 185 Sqmm XLPE Insulated cable, stranded compacted circular shaped aluminium conductor, overall PVC Sheathed cable confirming to IS 7098 Part-2, 2011 with latest amendments. = 60 Mtr. (Make: Havells/PolyCab/Finolex) (b). Outgoing Feeder i. 5 No. TP MCCB of 400 Amps, 36KA (Ics = 100%), for connection to ATS Starter each outgoing should also have a separate enclosure with one no. TP MCCB of 400 Amps, 36KA (Ics = 100%). Make : L&T/ABB/Siemens/Schneider/BCH. ii. 4 Nos. fully automatic transformer type starter 50 HP, 3 Phase, 415 volt, 50 Hz Starter with Air cooled including contactors, phase indicator & other auxiliary protection circuit, connections and small items i.e. thimbles, nut/bolt, etc with degree of protection IP 55 with allied accessories as per make : Andrewyule/AE/BCH/Schneider/Kilburn. iii. 4 Set. 3 Phase Volt Meter with SS, Amp. meter with SS including suitable size of CT digital type, RYB indicator set. Make : L&T/ABB/C&S/Schneider. Makes of Capacitor/ contactor/ MCCB/ APFC Controller : L&T/ Siemens/ ABB/BCH/Epcos/Shreem/Unistar. iv. 3x 95 sqmm LT cable 1.1 KV 120 Mtr. v. LT capacitor bank for electric motor of capacity 50 HP , 3 phase-415 V supply of size 120 KVAR. (capacitor bank shall be designed commenly for running of 3 No. Pumps at a time of each capacity 50 HP + 1 No. Pump is Ideal as standby operation) Note : For run 1 Nos. Motors at a time the squirrel cage induction electric motor of each capacity 150 HP, to run the raw water pump having discharge 581 cum/Hr with 36 mtr. Head) (Including third party inspection from govt. agency).

Supply, installation testing & commissioning of HDPE pipes including all accessories, specials, valves, hydrant assembly complete filtration unit from outlet to field hydrant. Providing, lowering, laying, aligning, fixing in position and jointing at all level/ depths ISI marked HDPE pipe of PE-80 grade and PN- 4 for sewer application as per IS 14333-1996 (amended up to date) in trenches in complete including cost of HDPE Specials, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer. Note: E/w to be measured and paid separately. Rate includes cost of all specials like bends, tees required during laying of pipe line along required alignment.110mm dia(292.58+20% for HDPE Specials, Hydro Testing. including all other fitting & accessories.)(CSR 28.15 D(e))

Supply, installation testing & commissioning of HDPE pipes including all accessories, specials, valves, hydrant assembly complete filtration unit from outlet to field hydrant. Providing, lowering, laying, aligning, fixing in position and jointing at all level/ depths ISI marked HDPE pipe of PE-80 grade and PN- 4 for sewer application as per IS 14333-1996 (amended up to date) in trenches in complete including cost of HDPE Specials, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer. Note: E/w to be measured and paid separately. Rate includes cost of all specials like bends, tees required during laying of pipe line along required alignment.140mm dia(459.76+20% for HDPE Specials, Hydro Testing. including all other fitting & accessories)(CSR 28.15 D(g))

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia. (HSR 4.16.1.2)

Hydrant Assembly complete 4"(5176.77+26.8% price escalation+12% GST component extra liable now)

Hydro cyclone filter 192.67 cum/Hr (174971.55+26.8% price escalation+12% GST component extra liable now)

Separator 192.67 cum/Hr(64063.73+26.8% price escalation+12% GST component extra liable now)

Air valve 2" with complete assembly(2679.58+26.8% price escalation+12% GST component extra liable now)

CI Non return valve 100mm (10Kg/Sqcm)(9108.45+26.8% price escalation+12% GST component extra liable now)

Pressure relief valve plastic 3" threaded(14549.96+26.8% price escalation+12% GST component extra liable now)

Scope of hydro analysis of the complete piping system and adequacy of the electro mechanical equipments

Complete operation of the project for 03 years including operation of pump houses, pipelines & accessories, electro mechanical items, micro system and complete in all respect (25 workers per month of different category i.e. plumber, electrician, fitter, supervisor & helper for 36 months)

Complete maintenance of the project for 3 years. (Take 2% of the total project cost)

M/S SHREE BALAJI BUILDERS