Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹7.3 LAccepted-Finance D 2 53 VIBHUTI KHAND GOMTI NAGAR GOMTI NAGAR LUCKNOW UTTAR PRADESH 226010 | LUCKNOW | UTTAR PRADESH | 226010 | L1 | Accepted-Finance Accept | |
| 2 | L2₹7.3 L+₹3,060 (0.42%)Accepted-Finance | L2 | Accepted-Finance Accept |
Tender Value
₹7.3 L
EMD Value
₹36,000
Closing Date
15 Sept 2020, 2:00 pmClosed
PROJECT MANAGER
U.P. Projects Corporation Ltd. Unit-8, 19 Marutipuram Faizabad Road, Lucknow
SUPPLY OF MATERIAL FOR CONSTRUCTION OF TYPE-II RESIDENCE FOR HOMEOPATHIC NIDESHALAYA AT 2 NABIBULLAH ROAD, LUCKNOW
2020_UPPRC_505751_3
33/PCL/PM/UNIT-8/2020-21
Open Tender
Supply of Materials
Item Rate
15 days
LUCKNOW
Please refer Tender documents.
2 documents required · 2 mandatory
₹2,950
PROJECT MANAGER UPPCL UNIT-8
₹36,000
3 Oct 2020
8 Sept 2020
15 Sept 2020
8 Sept 2020
15 Sept 2020
8 Sept 2020
Amount
Laying and Jointing PVC Pipe. Heading
Supply of Pozonolla Portland Cement as per ISI code 1489-2015 (Prism, Birla, ACC. JAYPEE or equivalent) Every bag shall be deemed to contain 50 kg. of cement. The suppliers may liable to submit the test report .
Supply of coarse sand shall be clean sharp and free from clay, loam, organic or any other foreign matter, shall be obtained from approved source. The contractor shall get the sample of coarse sand. approved by the Engineer-in-charge. Sand which in the opinion of the Engineer-in-Charge or his representative is dirty, must be washed to his satisfaction at the cost and expenses of the contractor coarse sand shall pass through a mesh, 4.75 mm. square measured in the clear. Sand shall not be used for concrete works if it contains more than 10% of fine grains passing through a 76 mesh sieve. should the fineness modulus be less than 2.25 unless specific permission is obtained from the Engineer-in-Charge.
Supply of 20mm guage approved stone grit from Stone chips or stone ballast for cement concrete (plain or reinforced) shall be hard, of uniform and fine texture.free form faults or planes of weakness and free from weathered faces. The ballast or chips must be free from loam, clay or any surface coating, free from organic matter or other impurities and screened, free of dust. Stone of black and hard variety as is generally available from quarries in KABRAI areas will be normally used. Stone aggregates from other sources may also be used provided the same is found suitable in the opinion of the Engineer-in-Charge. The opinion of Engineer-in-Charge must be recorded in writing. The ballast or chips shall be obtained by breaking from large blocks and must be more or less cubicle in shape stone grit grading shall be in conformity with the requirements laid down in the Indian Standards Specification IS : 383-1963 as shown below percentage passing for single sized aggregate of nominal size. 40mm Passing 100% 20mm passing 85-100% 10mm passing 0-20% 4.75 mm passing 0 - 5%
Supply of TMT bar different dia, Fe-500 conforming to IS code 1786-2008 including carriage loading unloading complete. 08mm dia
Supply of TMT bar different dia, Fe-500 conforming to IS code 1786-2008 including carriage loading unloading complete. 16mm dia
Supply of TMT bar different dia, Fe-500 conforming to IS code 1786-2008 including carriage loading unloading complete. 20mm dia
GST extra as per rule applicable
Shree Traders And Consultacy Services
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .