ADDITION ALTERATION AND SPECIAL REPAIRS TO BLDGS P 42 P 44 P 46 and P 168 AT SRINAGAR COLONY MINNIEBAY SRI VIJAYA PURAM

Amount

Taking down scrubs/vegitation growth from crevices completely upto any height and applying suitable chemical (herbicide) making good with PCC 1:2:4 or necessary plaster with CM 1:4 wiith WPC complete with all safety equipments etc., complete all as specified and as directed.

Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces including raking out joints, hacking for key etc., complete all as specified and as directed.

M&L for rendering 10mm thick plaster in CM (1:6) on brick/block or concrete surfaces finished even & smooth etc., complete all as specified and as directed.

M&L for rendering 5mm thick ceiling plaster in CM (1:3) on concrete surfaces finished even & smooth (without using extra cement) etc., complete all as specified and as directed.

M&L for rendering 5mm thick plaster in CM (1:4) over a backing coat of 10 mm thick in CM 1:6 (Total 15 mm thick) on concrete or block masonry surfaces including mixing water proofing compound on top layer as per manufactures instructions (or 3% by weight of cement) and finishing the top surfaces even and fair etc., including necessary scaffolding, tools and plants with safety precautions for working in G+3 building. (Note :Water proofing compound shall be measured and paid seperately under relevant item of this schedule as supply only).

Supply only water proofing compound ISI marked etc., complete all as specified and as directed. (Note : WPC may apply as per manufactures instructions or 3% by the wt of cement).

M&L for preparation of new plastered surfaces of wall and applying two coats of Distempering with 1st quality acrylic distemper ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour as per manufacturer's specification etc., Incl a layer of white putty 1mm thick over new plastered surface.complete all as specified and as directed.

M&L for newly plastered surfaces and applying two coats of Acrylic distemper ready mix over a coat of 1mm putty, on plastered surfaces of ceiling etc., complete all as specified and as directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L preparation of new wood/wood based surfaces of exc. 10 cm width or girth of any description and applying two coats of synthetic enamel paint over a coat of pink primer etc., complete all as specified and as directed.

M&L for preparing new steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer etc., complete all as specified and as directed.(on truss work & new pressed steel frame)

M&L for complete removal of existing treatment on wall by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc and applying two coats of Ist quality acrylic distemper over a coat of primer etc., complete all as specified and as directed.

M&L for applying a layer of 1mm thick wall care putty on wall and making surface even and smooth etc., complete all as specified and as directed.

M&L for complete removal of existing treatment and preparation of old surfaces of CEILING and applying two coats of Ist quality acrylic distemper over a coat of primer etc., complete all as specified and as directed.

M&L for complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping with mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean,free from dust, loose paint etc and preparation of old external surface and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, including necessary scaffolding, tool and plants with safety for working in G+3 building complete all as specified and as directed.

M&L for preparation of old painted wooden surface and applying two coats of synthetic enamel paint of any description exc 10 cm width or girth, etc., complete all as specified and as directed.

M&L for preparation of old painted steel surfaces over 10 cm in width or girth and applying two coats of syanthetic enamel paint etc., complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above ground level) etc., complete all as specified and as directed.

M&L for 25mm thick cement concrete type B-1, 1:2:4 (20mm graded agg ) as in flooring finished even and fair for correction of slope etc., complete all as specified and as directed.

M&L for 40mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded aggregate) as in floorings, finished even and smooth without using extra cement etc., complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 Type C-2 (using 40mm crushed stone aggregate) as in plinth protection finished even and fair without using extra cement etc., complete all as specified and as directed.

Demolition of precast concrete work built in cement mortar including all quoins arches pillars etc., complete all as specified and as directed.

M&L for Pre-cast cement concrete block masonry Type C1 1:3:6 (20mm graded aggregate) with solid blocks, exc.10 cm in width and setting in cement mortar 1:6, etc., complete all as specified and as directed.

M&L for precast cement concrete block masonry with solid Type C1 1:3:6 (20mm graded aggregate as per IS 383) of 10 cm in width and setting in CM 1:6 all as specified .

Dismantling floor, hearth or wall tiles including cement mortar bedding (but not backing) and removing serviceable tiles to stores and rubbish off the premises etc., complete all as specified and as directed.

M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor over and including 15mm thick screed bed in CM (1:6) etc., complete all as specified and as directed.

-Ditto all as per item No 26 above but in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile over 10mm thick backing in cement mortar (1:3) etc., complete all as specified and as directed.

M&L for coloured non-skid ceramic tiles 7 to 8 mm thick exc. 0.06 sqm but n.exc 0.11sqm area of each tiles in floor/ steps etc set and jointed in neat cement slurry and pointed in coloured cement to match as in floor over and including 15mm thick screed bed in CM (1:6) etc., complete all as specified and as directed.

M&L for glazed ceramic coloured/printed tiles 450x350x 7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile over 10mm thick backing in cement mortar (1:3) etc., complete all as specified and as directed.

M&L for coloured chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick in floors, steps, risers etc set and jointed neat cement slurry and pointed with mixture of white & grey cement in equal proments & no pigment, over and including 15 mm thick screed bed in CM(1:6) etc., complete all as specified and as directed.

M&L for 75mm thick cement concrete type D2, 1:4:8 (using 40 mm graded stone aggregate)as in sub base of flooring/ hard standing finishing the surface even & smoth without using extra cement etc., complete all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, approns and laid bedded and pointed in any mortar etc., complete all as specified and as directed.

M&L for Endura Vitrified step tiles 300mm x 1200 mm x 12mm thick in stair case thread step set and jointed neat cement slurry and pointed in white or coloured cement to match as in floor over and including 15 mm thick screed bed in CM (1:4) etc., complete all as specified and as directed. Note :- The tiles have embossed tread lines provide extra grip and bull nosed fully vitrified.

M&L for Endura Vitrified step tiles 200mm x 1200 x 12mm thick in stair case Riser set and jointed neat cement slurry and pointed in white or coloured cement to match the shade of tile over 10mm thick backing in cement mortar (1;3) etc., complete all as specified and as directed.

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed bed in CM(1:6) etc., complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as specified.

Taking down chowkats or frames (without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4.0 Sqm each.(including Aluminium windows/ventilators) etc., complete all as specified and as directed.

Taking down chowkats or frames (without taking off shutters from the frame) area n.exc 1.5 Sqm each.(including Aluminium windows /ventilators) etc., complete all as specified and as directed.

S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F for Factory made double extruded WPC (Wood Polymer Composite) solid door & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length etc., complete all as specified and as directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F Factory made single 30 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door(decorative type) shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws etc., complete all as specified and as directed. (Note: stainless steel butt hinges and necessary S S screws incl in this item)

S&F for second class hard wood 35 mm thick glazed or guazed and skeleton shutters open rebated and prepared to receive glass, gauge etc divided in to squares with plain, chamfered or rounded, mitred and rebated sash bars fitted with cut and mitred beads for securing glass etc including necessary arrangements to fit with pressed steel frame etc., complete all as specified and as directed.

S&F in repairs Powder coated Aluminium frames for Partition, Door, Windows ,sliding shutters and Ventilators with one or more rebates incl jointing cleat for fixing etc and powder coated aluminium skelton windows & ventilator shutter fixed with glass or gauge, side hung type without sash bars using standard aluminium section incl necessary Aluminium grill, jointing cleats, glazing clips, rubber packing powder coated aluminium snap beadings screws, powder coated aluminium fittings such as handles stainless steel adjustable friction stay hinges etc complete all as specified incl aluminium grills fixed to window frame aluminium anodised wire cloth fixed to aluminium frame all as specified and directed NOTE: (i) Payment under this item will be make only for the cost of aluminium section. However unit rate quoted shall deemed to include cost of rubber beading, fittings such as handles, SS friction stay hinges and fixing of 5mm thick glass etc. (ii) Supply only 5mm thick sheet glass and aluminium wire cloth be measured and paid separately. (iii) Weight of aluminium handle & SS hinges shall not be accounted for payment purpose .

S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 1.77 to 2.00 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). 3 Nos of Stainless steel hinges type B-21 100mm long (2 no.) suitable handle (1 no.) etc., complete all as specified and as directed.

S&F for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening etc., complete all as specified and as directed.

S&F for 4mm thick ordinary quality sheet glass and glazing with oil putty in square n.exc.0.50 sqm in each pane etc., complete all as specified and as directed.

S&F for 4mm thick figured glass pin head type and glazing with oil putty in squares n.exc 0.5 sq.m in each pane etc., complete all as specified and as directed.

S&F for Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples etc., complete all as specified and as directed.

S&F for Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed etc., complete all as specified and as directed.

S&F for factory made single extruded 18/19 mm thick WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws etc., complete all as specified and as directed. NOTE:- All joint should be filled with sealant

S&F for 150 mm long Brass handles, cast type, polished bright etc., complete all as specified and as directed.

S&F for 100 mm size hasp and stable , safety type , brass with mild steel hinges pin including bolt to hinge plate with scrows etc., complete all as specified and as directed.

S&F for contunoius (piano) hinges , mild steel , bright finish or electrogalvanished and width of flaps 30 mm (when open) etc., complete all as specified and as directed.

S&F for solid PVC door frame of size 50mmx47mm made out of 5mm wood grain printed PVC sheet edges will be painted to match with printed sheet reinforced with MS square tube in opening as per specification and drawing etc., complete all as specified and as directed.

S&F for factory made solid panel PVC Door shutter 30mm thick (Style) consisting of frame made out MS frame shall be covered with heat moulded wood grain printed PVC sheet & 5mm thick x 15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90ͦ C) used instead of exposed portion of PVC sheet beading having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail, & bottom rail Panneling of colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement at site as per specification and drawing etc., complete all as specified and as directed.

S&F for 125 mm long Butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11 etc., complete all as specified and as directed.

S&F for 150mm aluminium anodised barrel tower bolts of extruded section and fixed etc., complete all as specified and as directed.

S&F for 100mm aluminium anodised barrel tower bolts of extruded section and fixed etc., complete all as specified and as directed.

S&F for 300mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed etc., complete all as specified and as directed.

S&F for 150mm aluminium handles, cast type , anodised etc., complete all as specified and as directed.

S&F for 100mm aluminium handles, cast type , anodised etc., complete all as specified and as directed.

S&F for anodized aluminum door seals of 32mm (overall size) with standard 1mm thick aluminum sections and bottom brush and provision of counter sunk holes for screws etc., complete all as specified and as directed.

S&F in repair for 150mm Floor door stoper of aluminium alloy and tounge, anodised, with hard drawn steel sring, fixed in door etc., complete all as specified and as directed.

S&F in repair for door helical spring mild steel 300mm, ordinary rat tail rod patteren including roller and roller plate etc., complete all as specified and as directed.

S&F in repair stainless steel curtain rod 25mm dia steel pipe cutting into length as required at site with and incl SS end caps/lobs and SS wall mounting brackets etc., complete all as specified and as directed.

S&F in repair stainless steel curtain rod 15mm dia steel pipe cutting into length as required at site with and incl SS end brackets, fixed in cupboard and similar works etc., complete all as specified and as directed.

Refixing Aluminium windows size exc.1.5 sqm and n.exc 4.0 sqm any description in same/other opening after proper cleaning of tracks serviceable the same by means of repairing defective member, hinges etc and adjustment, greasing as necessary etc complete including taking down etc., complete all as specified and as directed.

Refixing Aluminium windows size n.exc.1.5 sqm any description in same/other opening after proper cleaning of tracks serviceable the same by means of repairing defective member, hinges etc adjustment, greasing as necessary etc complete including taking down etc., complete all as specified and as directed.

Taking down 20mm Steel / CPVC tubing and connections including cleaning for refixing or removal to store etc., complete all as specified and as directed.

Taking down 25/32mm Steel / CPVC tubing and connections including cleaning for refixing or removal to store etc., complete all as specified and as directed.

Supply and laying of CPVC pipes 25 mm dia outer bore SDR 11 &plain CPVC SDR 11 fittings (Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor etc) on walls /ceilings or laying in floors etc., complete all as specified and as directed.

Supply and laying of CPVC pipes 32 mm dia outer bore SDR 11 &plain CPVC SDR 11 fittings (Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor etc) on walls /ceilings or laying in floors complete all as specified.

Cutting chases in concrete block walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing etc., and making good, cutting not exceeding 10 cm girth etc., complete all as specified and as directed.

Taking down eaves gutter and rain / waste water pipes including all fittings any size and pattern etc., complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in treanches incuding necessary clamps etc to fixing as required etc., complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) bends of any radius with access door etc., complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) branch piece,single (single Y) equal or unequal with access door etc., complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) branch piece,double (double Y) equal or unequal with access door etc., complete all as specified and as directed.

S&F for 110mm bore PVC (SWR) junction single, (single T) equal or unequal with access door etc., complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) junction double ,(double T) equal or unequal with access door etc., complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) couplers etc., complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) vent cowl fixed on top etc., complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in treanches incuding necessary clamps etc to fixing on walls as required etc., complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) bends of any radius with access door etc., complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) branch piece,single (single Y) equal or unequal with access door etc., complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) branch piece,double (double Y) equal or unequal with access door etc., complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) junction single, (single T) equal or unequal with access door etc., complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) junction double, (double T) equal or unequal with accessa door etc., complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) couplers etc., complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) vent cowl fixed on top etc., complete all as specified and as directed.

M&L for PVC (SWR) floor traps 75mm bore with stainless steel grating (measured seperately) including jointing to waste pipe and in cement concrete 1:2:4 type B-1 etc., complete all as specified and as directed.

S&F for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement etc., complete all as specified and as directed.

S&F in repair of 1st quality vitreous china ware European type WC of size 540x375x415mm 'P' trap or 'S' Trap (pedestal pattern), any colour including necessary fittings (excluding flushing cistern and flush pipe) etc., complete all as specified and as directed.

S&F in repair of 1st quality vitreous china squatting pan Orissa pattern of size 580x440 mm, white colour with integral foot rests water closet including flush pipe but exluding flushing cistern, duly fixed in lime concrete bedding and making good of floor surface etc., complete all as specified and as directed.

S&F in repairs 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, any colour , with inlet, ball valve, float and handle including brackets, and necessary connections to pipes with PVC connections 20mm size with PTMT nuts of length 600mm etc., complete all as specified and as directed.

S&F in repairs PVC water closet seat cover (any description and any colour), closed pattern and mild steel chromium plated or aluminised hinging device etc., complete all as specified and as directed.

S&F in repair Heavy Duty Flexible Braided PVC waste pipe for sink and wash basin 32mm dia with length not less than 1000mm i/c PVC waste fittings of Approved make etc., complete all as specified and as directed.

S&F in repair Heavy Duty Flexible Braided PVC waste pipe for sink and wash basin 40mm dia with length not less than 1000mm i/c PVC waste fittings of Approved make etc., complete all as specified and as directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position etc., complete all as specified and as directed.

S&F in repair Vitreous China wash basin, white, flat back, size 450x300mm fixed on MS brackets including 32 mm bore CP waste coupling and PVC connections 15mm size with PTMT nuts of length 600mm etc., complete all as specified and as directed.

S&F in repair Pillar taps,heavy duty chromium plated, swan neck fancy type 15 mm dia cast copper alloy, with capstan heads, ,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed etc., complete all as specified and as directed.

S&F in repair CP Towel Ring fixed with and including Chromium plated brass screws and wall plugs (Minimum weight 90gms) etc., complete all as specified and as directed.

S&F in repairs 600 mm long CP Brass Towel Rail 20 mm dia fixed to wall with necessary chromium plated screws and wall plugs etc., complete all as specified and as directed.

S&F in repair brass chromium plated over head shower rose with arm 125 mm size with long body with swivel joint including fixing to CPVC/ steel pipe or union etc., complete all as specified and as directed.

S&F in repair Angular stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore etc., complete all as specified and as directed.

S&F in repair to Bib Taps, cast copper alloy heavy duty, 15 mm dia, Chromium Plated, long body Fancy Type screwed down for iron pipe and fixed etc., complete all as specified and as directed.

S&F in repair two way bib tap cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore etc., complete all as specified and as directed.

S&F in repairs 15 mm dia Stop cock chromium plated fancy type with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe/CPVC pipe or for unions and fixed etc., complete all as specified and as directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long etc., complete all as specified and as directed.

S&F in repair soap dish, brass, chromium plated fixed to wall with brass chromium plated screw etc., complete all as specified and as directed.

S&F in repair 125 mm dia CP grating incl joints with solvent cement etc., complete all as specified and as directed.

S&F in repair Kitchen sinks with drainage board made of stainless steel l.00mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including waste fittings like 40mm CP waste couplings etc., complete all as specified and as directed.

S&F in repair stainless steel plate rack of size 900x 750 x 250 mm made of 1.00mm thick stainless steel fixed into wall with necessary brass screws and plugs etc., complete all as specified and as directed.

S&F in repair Peg set (6 Pin) stainless steel cloth hanger for door / wall / Cupboards including fixing arrangements etc., complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description and any position as directed . (MS Gates and MS railing only taken)

M&L for stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories &stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement. etc., complete all as specified and as directed. (considered for Railing on balcony /staircase portion at any postition)

M&L for Special treatment of sunken portion of WCs, Bathroom, size of floor exc 0.75 Sqm n exc 1.75 Sqm as per following stages including taking down previously treated materials :- Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surface of existing sunken portion of WCs with wire brush to remove all loose dirt, oil grease etc . Stage 2:- Providing 10mm thick plaster in CM 1:4 with chemical of Dr. Fixit Pidicrete URP or plaster seal of STP Ltd Stage 3:- Applying Dr Fixit Primseal primer or STP Ltd(and allow to dry for 8 hours) under touch dry condition

Stage 4:- Applying two coats of water proofing decorative elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP(The surface after painting one coats shall be allowed to dry of 6 hours before next coats) all as per manufactutrer instruction. Stage 5:-Again rendering 10mm thick in CM 1:4 mixed with Dr Fixit Pidicrete URP or plaster seal of STP Ltd. Stage 6. All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URP. Stage 7:- Making holes in wall and fixing 600mm long 20mm dia GI spout for draining the surplus water if any.

S&F pull-it 5 feet x 4 pipe Pulley Operated Clothes Drying Systems consisting of anodized Aluminium pipes, each of outer dia 22 mm and inner dia 19.8 mm Pulleys made up of Deinn with rope guide mounted on channel pair of length 24 inches (distance between two pipes is adjustable), locking system to hide rope knot. Channel to be mounted or fixed with self-tapping screws provided in kit, Rope will be Polyester braided undyed of 3 - 4 mm dia etc., complete all as specified and as directed.

Providing and injecting chemical emulsion for post constructional anti-termite Treatment of at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same. Note: The same shall be carried out through authorised agency having valid licence.

Providing and injecting chemical emulsion for post constructional anti-termite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.®Note: The same shall be carried out through authorised agency having valid licence.

Providing and injecting chemical emulsion for post constructional anti-termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed.Note: The same shall be carried out through authorised agency having valid licence.

Demolition of existing water proofing treatment by brushing with wire brush, cleaning of terracing by taking down , existing plaster etc, cleaning of all foreign material such as fungus mass dust etc, roughing surface of corner to roof by wire brush etc., complete all as specified and as directed.

M&L for Average 40mm thick in slope plain cement concrete type B-1 1:2:4 (nominal mix) using 20mm graded stone aggregate for correction of roof slab / roof padding making necessary slope etc., complete all as specified and as directed.

M&L for 10mm thick rendering/screed on terrace or concrete surfaces in cement mortar 1:4 finished even and fair and apply WPC (WPC @3% by wt of cement measured and paid seperately) etc., complete all as specified and as directed.

M&L for laying APP modified water proofing treatment over existing RCC roof slab with following specification including brushing off the surface to receive the treatment obtain the required surface :- (a) Applying bituminous primer @ 1.2 kg/Sqm on the prepared dry roof surface. (b) Laying min 3mm thick APP membrane Plain finish weight not less than 3 to 4 kg per sqm by torch application with minimum 10cm side lap and 15cm end lap. (c) Applying two coat of aluminium paint incl preparartion of surface. Note :Laying of APP membrane shall be got done through an authorized applicator of manufacturer.

Removing loose and broken concrete by chiseling/ mechanically etc from the roof slab, column, beam and similar structural members cutting edges, cleaning the dismantled portion with wire brush etc to make the reinforcement naked and remove dust, dirt and other foreign particle etc and washing with clean water with pressure and removing rubbish off the premises to a distance not exceeding 50 mtrs and including necessary safety precautions and scaffolding up to a height of 15 mtrs etc., complete all as specified and as directed.

S&F for Hard drawn steel wire fabric weight not exceeding 4 kg per square metre, cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia welding to existing reinforcement etc., complete all as specified and as directed.

M&L for applying one coat of epoxy bonding coat as per manufacture's instruction to bind old concrete surfaces of soffit of slab, column, beam and similar structural members for new gunited / cement surface. Make : IPH 21 EB of Harjas Coatings & Polymers / Nitobond EP of FOSROC or equivalent make in Dr. Fix it of Pidilite Industries / MC Bauchemie / BASF

M&L for pressure gunniting 40 mm average thickness at a pressure not less than 6kg/ sqcm to all affected RCC structures in cement mortar 1:3 duly modifying with mixture of Nitobond SBR of FOSROC @ 7 litres per 50 kg of cement or IPH-CC resin and IPC-CC hardner of make Harjas Coating & polymers in equal proportion @ 5% of weight of cement or equivalent in Pidilite industries Ltd (Rate included ) and including necessary safety precautions and scaffolding, Tools and plants complete all as per manufacturer's instructions etc., complete all as specified and as directed.

M&L for non shrink, cementatious Micro concrete using Renderoc RG manufactured by M/s. Fosroc Chemicals India [P] Ltd. or its equivalent in Dr. Fixit or IPH-411 of M/s Harjas Coatings & Polymers modified with 12.5mm graded crushed stone aggregate in the ratio by weight (18kg aggregate: 25kg micro concrete) respectively duly modifying with mixture of Nitobond SBR of FOSROC @ 7 litres per 50 kg of cement or IPH-CC resin and IPC-CC hardner of make Harjas Coating & polymers in equal proportion @ 5% of weight of cement or equivalent in Pidilite industries Ltd (Rate included) as per manufacturer's instructions, as in sides and soffits of beams,jacketing of columns, ,roof slab and similar structural members including necessary form work for fair finished surfaces use and waste of water tight form work to facilitate pouring of micro concrete, including necessary demolition of RCC any description complete all as per manufacturer's instructions etc., complete all as specified and as directed.

M&L for applying polymer modified cement mortar rendering 15mm average thick in CM 1:3 on gunnited surfaces duly mixing polymer modifier 'Nitobond AR' of make: M/s Fosroc Chemicals India (P) Ltd. @ 10 Ltr per bag of cement or IPH-CC resin and IPC-CC hardner of make Harjas Coating & polymers in equal proportion @ 5% of weight of cement or equivalent in Pidilite industries Ltd (IPH CC resin measured and paid seperately)complete finished even and smooth without using extra cement all as specified and as per manufacturer's instructions.

M&L for applying curing compound of approved make as specified [Concure WB of M/s. Fosroc Chemicals India [P] Ltd. or its equivalent in Dr. Fixit or Harjas Coatings] on newly polymer modified cement mortar as in newly gunited and micro concreted surfaces complete all as per manufacturer's instructions etc., complete all as specified and as directed.

M&L for cutting out existing cracks in concrete surfaces / masonry wall / RCC slab, forming a 'V' Groove of 25mmx40mm size, cleaning the groove thoroughly with air blower, priming the groove with mixture of IPH-CC Resin & Hardener manufactured by Harjas Coatings & Polymers or equivalent proportions using spray gun/brush, filling the groove with putty of IPH-CC Resin, Hardener & admixture manufactured by Harjas Coatings & Polymers or equivalent in M/s Fosroc Chemicals India [P] Ltd. or Dr. Fixit, mixed in 1:1:4 ratio, and finally applying a seal coat of same as of primer coat with brush complete all as per manufacturer's instructions etc., complete all as specified and as directed.

M&L for drilling required size upto 16mm dia holes in to RCC slab / wall / Column /beams to a depth of 100 to 150mm & provide shear connector of 12mm dia rod of length of 150mm bent to "L" shape with 75mm to be embedded in hole & 75mm to be used as dowel, fixed with polyster resin grout mixed mechanically and pour the same into the hole and insert the shear connector and finish the top; allow the same to set complete all as per manufacturer's instructions etc., complete all as specified and as directed. [Make of grout : 'Lokfix S' of make : M/s Fosroc chemicals India (P) Ltd. or equivalent

M&L for Drilling of holes required size upto 16 mm dia and upto 100 mm depth in concrete surface/ crack surfaces using rotary cum hammer drill and fixing PVC/ brass nozzles with IPH 21 epoxy based sealent to facilates grouting. The spacing of nozzles shall be as decided by Engr-in-Charge etc., complete all as specified and as directed.

M&L IPH 21 (G) high strength epoxy based for grouting over the concrete surface by injecting through the nozzles to strength the weak concrete. The system should have suitable viscosity which will enable it to soak into weak concrete and on subsequent polymerisation bind the loose and weak concrete. The minimum requirements of epoxy based grout material are as under:1.Compressive strength @ 7 days : 60 N/sqmm. 2 Tensile strength @ 7 days: 20 N/sqmm. 3. Pot life : 30 to 45 min

M&L for applying IPH RB -107 polymer based rust-remover (pH value –12 ) and applying IPH RB -167 Polymer based rust preventive (pH value-9) to all exposed reinforced bars etc., complete all as specified and as directed.

Note for sl. no. 127 to 138:- (i)All the structural strengthening items from above shall be executed by the authorized applicator only. The certificate in this regard shall be held in records of GE. (ii) To carryout NDT tests at the relevant locations and in relevant numbers to assess the strength of structural members after the completion of repairs under structural rehabilitation i.e. Rebound hammer test to be carried out in each floor of buildings and checked for target strength of M-25 concrete. Testing will be done by any local firm with approved and calibrated T&P in the presence of Engg-in-charge payment of structural repair items be released only after tests on repair surfaces and approval of GE, Minniebay. Firms for the same as per availability be approved by GE Minnie Bay. Firm will take only test readings in the presence of Engr-in-charga. Calculations will be carried out by concerned AGE/JE in-charge payments for the taking reading is deemed to be included in his quoted rates and no extra payment be claimed on this account.

M&L for MS TMT bars 10mm dia and over cut to length bent to shape reqd including cranking, bending spirally for hooking for columns, hooking ends and and binding with and including mild steel wire (annealed) not less than 0.9mm dia etc., complete all as specified and as directed.

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Fe.290.Gde-E-165 etc., complete all as specified and as directed.

M&L for MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment confirming to Fe 410 -W (Gde- E- 250) quality- A etc., complete all as specified and as directed.

S&F Mild steel screw bolts (machine made) 5 to 10 mm dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n.exc. 10 cm long etc., complete all as specified and as directed.

S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.(Note : Height of the bldg up to G+3 storey including necessary safety arrangements) etc., complete all as specified and as directed.

S&F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley gutter, drip, and straight flashing all as specified and as directed.(Note : Height of the bldg up to G+3 storey including necessary safety arrangements) etc., complete all as specified and as directed.

S&F Aluminium flat iron work in wind ties 40x6mm size fixed with 50mm/ 75 mm aluminium self staging screws with integral EPDM washer screwed in roof covering all as directed.(Note :- Height of the bldg up to 15 mtrs including necessary safety arrangements) etc., complete all as specified and as directed.

S&F for Mild steel, plain, black sheet 1.25 mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles as required etc., complete all as specified and as directed.

Demolition of Reinforced Concrete of any description and in any position not otherwise specifically provided for RCC overhead tank, parapet, railing, facia etc complete all as specified and as directed

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation, complete all as specified and directed.

S&F for CPVC pipe outer diameter of 25mm Tank Adaptor as a connecting niple for water tank storage complete all as specified and directed

S&F for CPVC pipe outer diameter of 25mm connecting nipple for ball valve fixing for water tank storage complete all as specified and directed

S&F in repair Bore dia of pipe in 25 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./ 25mm-455gms/ 40mm - 690 gms)

S&F in repair Vitreous China wash basin, white, flat back, size 630x450mm fixed on MS brackets including 32 mm bore CP waste coupling and PVC connections 15mm size with PTMT nuts of length 600mm etc., complete all as specified and as directed.

Excavation in trenches in hard / dense soil n.exc. 1.5M wide and n.exc. 1.5M deep and getting out all as specified and directed

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5M complete all as specified and as directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified and as directed.

M&L PCC (1:4:8) Type D2 using 40 mm graded stone aggregate in foundations, filling and mass-concrete all as specified

M&L for PCC (1:3:6) Type C2 ( using 40 mm graded stone aggregate) in surface channels and PCC drains complete all as specified and directed.

M&L for providing cement concrete type B-1, 1:2:4 (using 20mm graded aggregate) as in coping, benching, and similar works slightly rounded or chamfered angles and throating including necessary form work as directed

M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone agg as in cover slab and set in cement mortor 1:6 complete incl necessary form work.(Reinforcement shall be measured and paid seperately )

M& L for Cutting into existing manholes for connecting new drains internal dia of pipe 150mm , making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required

Demolition and breaking up drain pipes of internal dia 150mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as spd and directed

M&L for DWCE Pipe 150/175 mm (ID/OD) complete laid in trenches including testing alongwith necessary jointing material tees/ union / socket etc complete all as spd and directed by Engr-In-Charge

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground Concrete, brick work, masonry, etc.

Dismantling fencing wire mesh any type.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in & raming earth/ broken rubble mixed with earth around, in layers n. exc. 25cm, watering, & removing surplus soil to a distance n exc 50m & making good surface in soft/loose soil.

S&F MS framed work such as fencing post including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified

M&L Stainless steeI chain link fencing 3.5mm dia with 50mm x 50mm mesh including fixing of MS line wire / rod, flat iron & machine made hexagonal or square head bolts to fencing posts complete all as specified.(supply only of MS rod and bolts will be measured and paid seperately) all as specified

S&F for only stainless steel screw bolts n exc 12 mm dia machine made with hexagonal or square head at one end and screwed the other or screwed both ends for fixing of chain link fencing all as specified and directed.

Supply only 10 mm dia Round bars for support to chain link fencing confirming to Fe-290 (Gde E-165) complete all as specified and as directed.

M&L for taking down carefully existing aluminium point wiring (light, fan, socket or power) complete fittings fixture such as switches Ceiling roses, pendents,regulators, sockets etc to be measured separately)unscrewing from Board/outlet boxes, fittings & fixtures such as switches, sockets, ceiling rose lamp holder tube/ceiling fitting, bulk head fittings, tube lights & regulator etc and making good disturbed surfaces of walls, floors etc. complete all as specified and as directed.

M&L for taking down unserviceable submain wiring alongwith batten/PVC/steel conduits etc and making good disturbed surfaces of walls/ floors to match the existing surfaces all as specified and as directed. Note: Three runs of cable with one run of PVC conduit/ PVC casing & capping will be measured as one RM.

M&L for taking down carefully existing old DBs any type and making good disturbed surfaces of walls to match the existing surfaces complete all as specified and as directed

M&L for point wiring with two run of PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm (FRLSH), PVC conduit medium grade/PVC casing caping and pressed steel terminal boxes (for mounting modular switches /modular sockets/ modular regulators etc) complete and drawing one run of 1.5 sqmm PVC insulated unsheathed multistranded copper conductor cable (FRLSH) as earth continuity wire in green colour connected to common earth and each terminal box/fitting all as specified and as directed Note: The quoted rate inclusive for the following :- (a) GI metal flush box and Modular cover plate with frame of any module complete. (b) Proper colour coding is to be followed as per IS Specification. (c) wiring shall be concealed/ on surface with rigid PVC conduit medium grade/PVC casing caping as per site requirement.(d) Electric Wiring test sheet after completion of wiring to be submitted before claiming payment.(e) Cutting chases/making good disturbed surfaces of wall for fixing concealed conduit wherever required will be measured and paid separately.

One light point controlled by one one way switch

One light point controlled by two 2-way switches

One ceiling fan point controlled by one switch and regulator

One exhaust fan point controlled by one switch

One 3 pin socket outlet 5/6 Amps independent.

One 3 pin socket outlet 5 Amps on the same board with other switches

One bell/ buzzer point controlled by one push button independent

All as per item No 173 above but cable with 4.0 sqmm size for socket outlet 15 amps, independent.

S&F modular switch one way 6 Amps, 1 module complete all as specified and as directed

Supply & fixing modular switch two way, 6 Amps, 1 module, 240 volts complete all as specified and as directed

S&F modular switch one way 16 Amps, 1 module complete all as specified and as directed.

Supply & fixing modular bell push one way, 6 Amps, 1 module, 240 volts complete all as specified and as directed

S&F modular socket, 2/3 pin 6 amps, 2 module complete all as specified and as directed.

S&F modular socket, 2/3 pin 6/16 amps, 2 module complete all as specified and as directed.

S&F ceiling Rose, 3 terminal polycarbonate isolated body complete all as specified and as directed.

Supply and fix Bell Ding Dong complete complete all as specified and as directed

Supply and fix Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

S&F LED inverter bulb 12 watt, 230 volts,50 Hz, lumen 1200 lm, Charging time 8 to 10 Hours, backup time 04 Hrs, operating temperature -10 to 50 degree celcius,back time 04 Hours, complete all as specififed and direccted.

M&L for submain wiring with two single core PVC insulated unsheathed multistranded copper conductor cable of size 6 sqmm (FRLSH) and one single core PVC insulated unsheathed multistranded copper conductor cable green colour of size 6 Sqmm (FRLSH) as earth lead in and including concealed with PVC conduit medium grade of suitable size or surface wiring with PVC casing caping of suitable size and making good the disturbed wall surfaces to match with existing specification including takind down unserviceable submain wiring complete all as specified and as directed. Note : (i) Three run of cable with one run of PVC conduit/PVC casing and caping will be measured as one length. (ii) Wiring shall be concealed/ on surface with rigid PVC conduit medium grade/PVC casing caping as per site requirement. (iii) Cutting chases/ making good disturbed surfaces of wall for fixing concealed conduit wherever required will be measured and paid separately

All as per item No. 186 here-in-before but with 4.0 sqmm cable complete all as specified and as directed.

All as per item No. 186 here-in-before but with 1.5 sqmm cable complete all as specified and as directed.

S&F LED lights fitting 20W, >120lm/watt, CCT value 6500K, surge protection of 2 KV, 4 feet 220V, AC IP-20, aluminium housing with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F LED 20W inverter batten type fitting 3/4 feet long aluminium extruded housing, charging time 10-12 Hrs with min battery capacity for 04 Hrs backup, IP-20 ,rated voltage 230 V, 50 hz, system wattage 20W +/- 10%, system current less than 102 mA, power factor more than 0.95, system lumen efficiency 100lm/watt, CCT 6500K, CRI more than 80, THD less than 30%, driver efficiency more than 85%, complete all accessories prewired and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt, >120lm/watt, IP-20, with CCT 6500K, 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing round LED surface downlighter 15 watt, 1200lm, IP-20, CDL with CCT 3000K (warm white) for ceiling complete all as specified and as directed.

Supply and fixing LED oval shape single head wall light 12 Watt max, metal body, bronze colour including lamp with CCT 3000K (warm white) complete all as specified and as directed.

Note for item No 189 to 193 : (i) Driver efficiency more than 85% (Constant current driver) (ii) Non isolated type driver (iii) THD less than 20% (iv) LED driver current less than 60 mA (v) Efficiency of LED Chip more than 130 lm/watt (vi) Efficiency of LED Fixture 100 lm/watt (vii) Surge protection 2.0 KV & above as per IEC standard (viii) working humidity 95%RH (ix) Life 50000 Hrs at 70% lumens (x) CRI more than 80 (xi) Working temp -10 degree to 50 degree C (xii) Heat Sink extruded aluminum (xiii) junction temperature 85 degree C (xiv) Body of fitting Extruded Aluminum (xv) impact code Min IK 03 or more ( xvi) LM79 report from third party (instead of company in house lab) NABL/UL accredited lab (xvii) LM 80 report from LED manufacturer (xviii) Low/High voltage, reverse polarity, overload and short circuit protection inbuilt in fixture (xviiii) IP-20 .(xx) Test certificates to be submitted before commencement of work/ claiming for payment .(xxi) Warranty certificate for minimum 2 years to be submitted from OEM.

Supply & fixing BLDC ceiling fan 1200mm sweep with blades, suitable electronic remote as per OEM design, down rods and connected accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM, 5 star rated, equipped with brushless direct current motor (BLDC) of wattage < 28W including provision of cable from ceiling rose/connector to fan including taking down unserviceable ceiling fan and deposited to MES store yard complete all as specified and as directed.

Supply & fixing exhaust fan made of metallic body complete with louvers, voltage 230V, 50 HZ, RPM 900, sweep 300mm and exhaust fan shall be fixed with suitable size of buzzer bolt/hold fastner including making hole to the wall surface of any type/girth and at any height for fixing of exhaust fan and provision of cable from ceiling rose/connector to fan complete all as specified and as directed.

Supply & fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 HZ, RPM 1200, Copper winding of sweep 250mm and exhaust fan shall be fixed with suitable size of buzzer bolt/hold fastner including making arrangement to the window of any type and at any height for fixing of exhaust fan and provision of cable from ceiling rose/connector to fan complete all as specified and as directed.

Supply & fixing electric water heater, storage type, electro plated steel body as per OEM design with element free induction heat transfer technology through induction coil capacity 25 litre, BEE 5 star rated with reduction heating time 10-12 mins and with digital temperature display, live temperature with smart mode, automatic operation of water heater for on and off time complete with all accessories such as safety valve, thermostat, NRV, connection piece fastner bolts including stainless steel hose pipe complete all as specified and as directed.

Supply ,Installation ,Testing & Commissioning as in repair Microprocessor based Single phase tamper proof electronic smart energy meter( pre paid/ postpaid)rating with 2 wire 240 Volts, 50 HZ, of range 5-60 Amps, confirming to IS 16444 with DLMS protocol , LED/LCD display and parameters like Voltage, Current, Frequency, Power, Power factor, KWh/ KVA,Network work topology GPRS/LONG RANGE RF compatible for smart energy billing system both post paid and prepaid all as specified and as directed by Engr- in- Charge Note : (i) Old unserviceable meter will be deposited to MES store yard. (ii) The scope of integration of digital smart meter with server/software is not included in quoted rate and it will be considered separately.

Supply and fixing Thermoplastic/ Polycarbonate/ sealed moulded meter box, IP-43, weather proof & water proof single door with locking arrangement, transparent meter viewing window glass suitable for smart single phase meter complete all as specified and as directed.

Supply and fixing MCCB DB VTPN 4 way IP-54, IK-09 made of sheet steel phos phatised, powder painted, neutral link, earth bar and Din rail 415 Volts with double door, suitable for MCCB 4 Pole 100 Amps, 16KA as incomer and MCB Single Pole as outgoing complete all as specified and as directed.

Supply & fixing MCB DB's SPN 12 way, IP-54, IK-09 double door, sheet metal enclosure, 240V including suitable size of copper ferrules for fixing of cable complete all as specified and as directed. Note for item srl No 200 & 201 : (i) MCCB and MCB will be measured and paid separately. (ii) The cost for flushing of Distribution box in any type of wall and making good disturbed surfaces with existing colour shall be deemed to be included in the quoted rate

Supply & fixing Single pole and neutral enclosure with a two pin and earth plug and socket suitable for RCBO 2 pole, 20 to 40 amps rated complete all as specified and as directed. Note : RCBO will be measured and paid separately.

S&F RCBO 40 Amps, double pole 240V, AC type, 30 mA complete all as specified and as directed.

S&F RCBO 25 Amps, double pole 240V, AC type, 30 mA with sheet metal enclosure complete all as specified and as directed.

Supply and fixing MCB SP 6-32 Amps ,10 KA, 'C' Curve, 230 Volts ,50 HZ complete all as specified and as directed.

Supply & fixing MCCB 100-160 Amps, thermal adjustable, 16 KA , ICS = 100% ICU, AC 415 Volts, four pole including providing aluminium lugs for incoming and out going cables complete all as specified and as directed.

Supply and fixing LED building security light fittings comprising of epoxy powder coated housing, enclosed with glass cover in frame with lumen output not less than 2500 lumens suitable wattage for efficiency not less than 120 lumens/watt having secondary optics min wattage 25 watt with ingress protection IP 65/66 and potted electronic driver of minimum IP 67 with THD less than 10% CRI>80, P.F>0.95, CCT 3000K (warm white), IK>08 SPD of capacity 5 KV and testing on completion complete all as specified and as directed. complete all as specified and as directed.

M&L for GI bracket for street light fitting made out of 25 mm bore pipe ISI marked light grade GI tube bent to shape required not less than 1.20m long fixed with and including MS flat iron clamps made out of 25x3 mm GI flat, bolts, nuts and washer etc., complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3½ core including taking down old unserviceable cable complete all as specified and as directed.

Supply and laying Double wall corrugated HDPE pipe ISI marked of size inner dia 32mm including specials such as couplers, bends with smooth internal and corrugated external surface for non presuure under ground cable etc., complete all as specified and as directed.

M&L for cutting chases in concrete block walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed PVC Conduit etc., and making good, cutting not exceeding 10 cm girth etc., including making good disturbed surfaces with existing wall colour complete all as specified and as directed.

M&L for earthing complete with Galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below GL) with top edge of earth plate not less than 1.5 Mtr below normal ground level, earth plate surrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanised earth strip 25x4mm connected by means of bolts, nuts, check nuts and washer of galvanised iron or steel, provision of 40 mm dia GI pipe medium grade for protection of GI earth strip and 20mm dia GI pipe medium grade for watering arrangement and PCC (1:3:6) , type C1 chamber, MS funnel, wire gauge, 50 mm thick RCC 1:2:4, type B1 earth pit cover with 6 Nos, 8 mm dia high strength deformed steel TMT bars on both ways including necessary excavation in any type of soil, returning, filling in, removal of surplus soil to distance n exc 50 mtr, provision of charcoal and salt complete all as shown in electrical plate No 3 of schedule Part-I. Note: (i) Cost of GI earth strip and GI protection pipe upto 7.5mtr length shall be deemed to be included in the rate quoted for this item (ii) The unit rate shall also includes for Wire mesh, funnel, excavation, PCC chamber pit and test point complete. (iii) Quoted rate deemed to be inclusive of connecting incomer DB of bldg with suitable size of single core aluminium conductor cable or copper cable and CPVC pipe complete.

Supply and fixing in replacement CPVC ball valve for the following sizes of CPVC pipes :-

(a) 20 mm bore

(b) 25 mm bore

(c) 50 mm bore

Taking down old unsv CI/GI water tubing with all fittings, laid in trenches/fixed on wall/on roof etc of the folloing sizes :-

(a) 20mm bore

(b) 25mm bore

(c) 50mm bore

Taking down old unsv CI/GI water tubing with all fittings, laid in trenches/fixed on wall/on roof etc of the folloing sizes :-

(e) 100mm bore

(f) 150mm bore

S&F in replacement CPVC pipes SDR-11 including fittings, brass threaded special, Nipples for fixing gun metal valves/CPVC of following sizes as specified and directed incl necessary scaffolding for fixing rising mains upto G+3 floors:-

(a) 25mm Outer Dia

(b) 32mm Outer Dia

(c) 63mm Outer Dia

Note :- All CPVC/GI tube fixing on wall / roof should be fixed with clamp and in slab CPVC/GI tube passing through PVC pipe of suitable size by fixing with PCC and plastering in cement mortar and make surface as existing condition so that no water is leaking through pipes hole.

Supply, Laying, jointing and testing Ductile Iron pipes with spigot and socket ends centrifugally class K-9 , as in trenches of following bore in new or old locations. (Joints & DI specials shall be measured and paid separately).

(a) 100mm bore

(b) 150mm bore

S&F in replacement of CI Bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch. "Y" junction, double branch, cross (all sockets or socket and spigot or flanged) collars, caps and plugs upto 200mm bore. make Electro steel or equivalent ISI Marked all as specified and directed by Engr-in-Charge.

Cutting cast iron pipes and reducing to required length before laying for DI pipe of size 100 mm bore all as specified and as directed at site

Cutting cast iron pipes and reducing to required length before laying for DI pipe of size 150 mm bore all as specified and as directed at site

S&F in replacement rubber gasket joint for CI/DI for 100 mm suitable for spigot and socket pipes and fittings all as specified and directed by Engr-in-charge

S&F in replacement rubber gasket joint for CI/DI for 150 mm suitable for spigot and socket pipes and fittings all as specified and directed by Engr-in-charge

Supply and fix sluice valve 100 mm bore class PN1.6 including flange screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed all as specified and directed by Engr-in-Charge.Make :-Kirlosker or equivalent.

Supply and fix sluice valve 150 mm bore class PN1.6 including flange screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed all as specified and directed by Engr-in-Charge.Make :-Kirlosker or equivalent.

M & L for construction of valve chamber of internal size 1500x1500x1000 mm with block masonry in cement mortar 1:6 , with Plain Cement Concrete (Nominal mix) 1:3:6 type C2 sub base plaster internally and exposed external surface in cement mortar 1:4 (15 mm thick and provision of valve chamber cover made out of MS sheet 3.15 mm thick welded to angle iron frame 40 x 40 x 5 mm made out to double / single door type with hinges and providing proper locking arrangement duly painted with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and all as directed by Engr-in-Charge.

Excavation in trenches for taking out, laying of pipes not exc 1.5 mtr wide and not exc 1.5 mtr in depth and getting out in soft/loose soil complete all as specified and directed.

M & L for cutting of existing bitumenous road for laying of GI / CI / DI pipe lines of size all as speciefied and as directed by Engr in charge

M&L for structural steel for pipe support of any size/thickness consisting of bends,straps,supports,angle iron,MS pipes,chennels,plates,clamps,nut bolt etc,complete of grade Fe 290 Gde E 165 including painting with 2 coats of synthetic enamel paint over a coat of red oxide primer complete.

M&L for cement concrete in foundations for supportts to pipe supports/pedestals of type 1:2:4 type B2 (40 mm graded) aggregate

City Constructie Pvt Ltd (BID ID -3337083)

Hindustan Traders (BID ID -3339605)

M/s Sriya Enterprises (BID ID -3339939)