Construction of Inspection Hut Bhoranj, Distt Hamirpur

Amount

Excavation in foundation trenches etc. in all kinds of soil such as pick work,jumper work blasting work in soft or hard rook or by cum chiselling soft/ hard rock where blasting is prchibited in all leads and lif-ts including trimming and dewatering where ever required dressing of sides and bed stacking the excavated soil clear from the edge of excavaton and then returning the excavated soil after completion of work in 15cm layers when required into plinths, side of foundation etc. Consolidating each deposited layers by remming and watering and then disposing of all surplus excavated earth as per directions and to the entire satisfaction of Engineer in charge within all leads and lifts.

Providing and laying cement concrete 1:4:8( 1 cement:4 sand :8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth.

Providing and laying cement concrete work 1:1.5:3( 1 cement :1.5 sand :3 graded stone agg. 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:-

Foundation , footing , basis of column and the like and mass concrete

Wall any thickness but not less than 0.10 mtrs thickness attached pillaster butresses, plinth and strin courses from ktop of foundation up to floor two level as per direction and to the entire satisfaction of Engineer- in -charge.

Column, Pillar, posts, struts, upto floor two level. as per direction and to the entire satisfaction of the Engineer-in-Charge.

Suspended floors, roofs, landings, shelves and their support balconies , beams girders, bressumers, and cantilever upto floor two leval as per direction and to the entire satisfaction of the Engineer-in-charge.

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto floor two level.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring blow supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in following item including carriage of material in all leads & lifts..

Foundation, footings basis of columns etc. and mass concrete.

Flat surface such as soffits of suspended floors, roofs, landings and like floors etc. upto 200mm in thickness

Vertical surfaces such as wall (any thickness) partitions and the like including attached pilasters, butresses, plinth and string courses and the like complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Beams, cantilever, girders and lintels.

Columns, pillars, posts and struts Square, rectangular or polygonal in plan.

Edges of slabs and breaks in floors and walls: Under 20 cm. wide.

Providing Tor steel reinforcement for RCC work I/c bending ,binding and placing in position complete upto floor two level as per direction and to the entire satisfaction of Engineer-in-charge upto all lead and lifts.

Providing and laying 20 cm thick composit ASHLAR stone masonry with stone facing of chisel dressed stones one line dressed in cement mortar 1:6 (1cement :6 sand) and concrete backing with cement concrete1:3:6 (1 cement: 3 sand: 6graded stone aggregate 20 mm.nominal size) on inner face of walls including centring, shuttering and propping complete up to ALL heights /floors (EXTERIOR WALLS)

Brick work using common burnt building bricks in supper structurs in cement mortar 1:6 (1 cement :6 sand)2nd class as per direction and to the entire satisfaction of Engineer-in-charge upto all lead and lifts.(1st class brick )

Half brick masonary in common burent clay building bricks in super structure above plinth level up to floor two level in CM 1:3 ( 1 Cement, 3 Sand ) (1st class brick )

Providing wood work in frame of door and window and clerestory window and other frames wrought framed and fixed in position complete 2nd class Indian Teak wood.

Providing and fixing panalled glazed or panelled and glazed shutters for door, windows and clerestory windows including black emamelled iron butt hinges with necessary screws 40 mm thick using 2nd class Indian Teak wood.

Providing and fixing wire gauge shutter using galvanised MS wire gauge of IS gauge desigation 85 G with entire dia of .56 mm for door windows and clerestory window I/C bright finished black enamelled butt hinges necessary screws complete 40 mm thick 2nd class Indian Teak wood.

15mm thick cement plaster in single coat on rough sides of brick /stone /concrete walls for interior plastering upto floor two level I/c arrises, internal rounded angles, chambers and/or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar1:6 (1 cement :6 sand)

20mm Cement plaster in single coat on rough side of interior plastering upto floor two level ncluding arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:4 including carriage of material in all leads & lifts.

6mm cement plaster to ceiling in cement mortar 1:3 (1 cement :3 sand) in all leads and lifts.

Boulder filling under floors as per direction and to the entire satisfaction of Engineer-in-charge.

Kota stone slab flooring 20 mm (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing complete including carriage of material in all lieads and lifts 30mm thiick (13540200)

Providing and laying granite stone in flooring 20mm(average)thickness base of cement mortar 1: 3 (1cement:3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete including carriage of material in all lieads and lifts 20mm thiick

Providing and fixing 10mm thick polished/satin/matt/ antiskid water proof stain and impect resistent heavy duty vetrified tiles degital/ full body of Simpolo/KaJARIA/ Nitco or equivalant 60X60 OR600x120mm OR 80X120 x10mm manufactured of approved shade and colour inflooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) ointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of material in all leads & lifts. (13680000)(fixed with 5mm spacer,filled with epoxy)

Providing and laying spartic ceremic tiles 10mm.thick in flooring (600 x600mm/required. size) treads of steps laid on a bed of 12mm. thick cement mortar 1:3(1cement:3 sand) finished with flush pointing in white cement including carriage of material in all leads & lifts. (13600000)

White glazed tiles 8 to 10 mm thick in flooring, treads of steps and landing laid on a bed of 12 mm thick cement mortar 1:3(1 cement :3sand) finished with flush pointing in white cement complete in all respect including carriage of material in all leads & lifts.(13210000).(size of tile=30x60 or 30x120 cms

Providing and fixing 10mm thick antiskid water proof stain and impect resistent heavy duty vetrified tiles degital/ full body of Simpolo/KaJARIA/ Nitco or equivalant 60X60 OR600x120mm OR 80X120 x10mm manufactured of approved shade and colour inflooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) ointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of material in all leads & lifts. (fixed with 5mm spacer,filled with epoxy)

Providing and fixing plaster of paris (POP.) false ceiling 12 mm thick plaster, fixed over GI Mesh 5x5mm size, weight min. 0.70kg/sqmt ,GI sections (Min.0.350kg/mtr and wire mesh,:L-connectors, rawl plugs, complete as per Arhitectural drawings complete) all material chetak, Jindal make), fross and main section, grid sixe 45x90cms maximum complete as per directios of Architect/Engineer-in-Charge.

Providing and laying heavy duty precast cement conrete inter locking paver blocks vibro compacted upto M-50 grade ( NTC make) i/c border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for 60mm thick inter locking blocks complete in all respect including carriage of material in all leads & lifts.

Polishing two coats with PU(poly utherene) polish of required shade on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt, dust and sand papered smooth and including a coat of wood filler complete in all restpect including carriage of material in all leads and lifts.

Painting two coat (excluding Priming coat )on new wood and wood based surface with ready mixed paint brushing to give an even shade I/c cleaning of all dirt dust and other foreign matter, sand papering and stopping with while enamel paint as per direction and to the entire satisfaciton of Engineer-in-charge upto all lead and lifts.

Applying one coat for wood preservetive on previously treated wood and wood based surface after and I/c preparing the surface by thoroughly cleaning oil, grease,dirt and other foreign matter sand papering complete in all respect including carriage of material in all leads & lifts. with

Applying spirit or oil stains any colour on wood and wood based surfaces(sirca-light wall nut shade) to give an even surface including cleaning the surface of all dirt/dust required for PU. Poliosh finish,sand papering stopping and knotting complete.

Filling in plinth with sand under floors including watering ramming consolidating and dressing complete under flooring complete in all respect including carriage of material in all leads & lifts.

Applying spirit or oil stains any colour on wood and wood based surfaces(sirca-light wall nut shade) to give an even surface including cleaning the surface of all dirt/dust required for PU. Poliosh finish,sand papering stopping and knotting complete.

Providing and fixing 19mm thick water proof commercial board in shutter of cub board (Bhuttan make)with butt joints & fixing with nails & screws etc complete in all respect including carriage of material in all leads & lifts.

Providing and fixing 40mm thick burl ply of standard quality and of approved shade & design wall lining i/c fixing with approved adhesive, butt jointing and nails & screws complete (Base frame work to be measured & paid for separately) complete in all respect including carriage of material in all leads & lifts.

Providing and fixing 1.00mm thick coloured or plain lamination sheet (sunmica) on oards/ ply wood sheets with approved adhesive and nails etc complete in all respect including carriage of material in all leads & lifts.

Steel work welded in built up section Trusses and framed work i/c cutting houisting fixing in position and applying a priming Coat of red lead paint in beam joists channel angle tes flates with connection plate complete in all leads and lifts.

Providing and fixing modular hand rail of MS hollow pipe 50 mm dia welded in st length over M.flat at top of vertical blusters include i.e on coat of red oxide priming coat complete.

Providing and fixing Prepainted steel sheet roofing fixed with galvanised iron J & L hooks bolts ,nuts 8mm diameter with bitumen and GI washer field with white lead complete and rafter and trussed 0.60mm thickness sheet in all leads and lift.

Providing and fixing ridges of hips 60 cm over all in plain with galvanised iron GI sheet fixed J & L hooks in all leads and lifts.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops,dust and other foreign matters sand papered smooth to give final matt finish to the surface complete.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface complet in all respect including carriage of material in all leads and lifts (16105000).

Providing under layer for plinth protection of 75 mm thick (unconsolidated) bed dry brick/stone aggregated 40 mm nominal size will rammed and consolidated and grouted with fine sand including preperation of ground.

Painting two coat (excluding Priming coat )on new wood and wood based surface with ready mixed paint brushing to give an even shade I/c cleaning of all dirt dust and other foreign matter, sand papering and stopping with while enamel paint as per direction and to the entire satisfaciton of Engineer-in-charge upto all lead and lifts.

Providing and fixing bright finished aluminium sliding door bolts with nuts and screws etc. 200X16mm

P/F bright finished brass tower bolts (barrel type) with nuts and screws atc. Complete. 250X10mm

P/F bright finished brass handles with nuts and screws atc. Complete. 150mm

Proviing and fixing 40X3 mm iron hold fast 40cm long i.e fixing to frames with nut and screw etc. complete 150MM

Providng and fixing 12 mm thick and 100mmm vwide pelment with 25mm dia steel curtain rod and bracket i.e all fixtures.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1cement: 5sand:10graded stone aggegate) of 10mm nominal size) and 7.5cm cement concrete 1:2:4 (1cement : 2Sand : 4 graded stone aggregate of 20mm nominal size) and finished with a floating coat of neat cement complete as per standard design including of material in all leads and lifts

Providing and laying cement concrete 1:5:10(1cement:5Sand:10 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth in all leads and lifts (floor of storafe tank).

Providing and laying cement concrete 1:3:6(1cement:3sand:6 graded stone aggregate 40mm nominal size) with 15% plum and curing complete excluding cost of form work in foundation and plinth in all leads and lifts.

Providing and fixing SFRC Main hole cover with frame having frames size of 500mm internal dia should not be less than 100kg within all leads and lifts as per entire satisfaction of Engineer in charge.

Providing laying and jointing of PVC pipe of 110mm dia complete in all respect as per the direction of Engineer in charge.

Providing and fixing vent opening including cowl with I the top of the i.e. carriage all leads and lifts as per the direction of Engineer in charge.

Providing in RCC smoth finishing of the not exposed surface with cement mortar 1:3 (1cement: 3Sand) in all all leads & lifts as per direction and to the entire satisfacion of Engineer-in-Charge.

Providing and Laying in trenches GMS/MS tubes (L/M class) tube fitrting (earth work in trenches to be measured and paid for separately).

Scour pipe 65mm

Inlet, outlet pipe and overflow pipe 65mm .

Providing and fixing of double flanged cast iron sluic valve of following dia leader/kirloskar make and capable of withstanding the normal sheet pressure as per 14846 PN 1.0 with upto date ammenment upto all leads and lifts.

65mm dia (inlet, outlet pipe, overflow pipe and scour pipe).

Providing and fixing PVC pipe 100mm dia from roof to ground level

ELECTRICAL WIRING Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. Group-C

Wiring for light plug with 2x1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Supplying & fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required:-

4 modules(140mmx78mmx50mm)

6 modules(205mmx78mmx50mm)

8 modules (120mmx135mmx60mm)

12 modules (205mmx135mmx60mm)

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2x1.5 Sq. mm.

2x2.5 Sq. mm.

2x4.0 Sq. mm.

Wiring for circuit / sub-main with 4x6 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.6 Sq.mm. (4x6+2x6) HRFRLS/PVC insulated single core copper conductor cable for earthing wire from MCB box to main pannel board.

Wiring for circuit / sub-main with 4x10 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.10 Sq.mm. (4x10+2x10) HRFRLS/PVC insulated single core copper conductor cable for earthing three phase wiring in main pannel board for busbar.

Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

S.P. 5/ 6 Amps one way Modular switch.

5 pin, 5/ 6 Amps Modular socket outlet.

Bell push, Modular.

Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

S.P. 15/ 16 Amps one way Modular switch

6 pin,15/16 Amps Modular socket outlet.

Supplying and fixing TV. Socket outlet, modular rating switch /socket in the existing switch box / cover plate including connections etc. as required.

Supplying and fixing Telephone socket outlet, modular rating switch /socket in the existing switch box / cover plate including connections etc. as required.

Supplying and fixing ceiling rose on the existing junction box /wooden block including connections etc. as required.

Supplying and fixing of Double door-12 way single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper busbar, wireset, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required.

Supplying and fixing 63 Amps. Cat-A rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing sheet metal busbar chamber suitable for 200 Amp. 415 volts capacity with 4 No. copper strip bus-bars each of length 450mm & cross-sectional area(25.4mmx4.75mm), enclosure made from 1.6 mm thick M.S. sheet having overall dimensions (530mmx450mmx 150mm) nominal with all accessories including connections, earthing the body etc. as required.

Providing and fixing TP&N switch disconnector fuse unit cubical type, 415/500 volts with 3 No. HBC/HRC fuses, in sheet steel enclosure including drilling holes on the board, connections, earthing the body etc. as required. 100 Amp. Category-A

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of Single pole & neutral. Cat-B in the existing MCB DB complete with connections etc. as required:-

Supplying and erection of wall mounted metal boards for switch gear mounting of suitable size, with permissible variation in size of plus minus 5mm, welded frame work made of M.S. angle iron 35mm x 35 mm x 6 mm thick duly welded complete with 2.80mm thick M.S. sheet fixed with hinges as open able front, complete with locking arrangement including painting and bonding to the existing earth as required:-

Supplying and erection of 40/50/63 amps rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of Double pole. Cat-B in the existing MCB DB complete with connections etc. as required:-

Supplying and fixing 40 Amps. Cat-B rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 Amps, 240 volts, SPN industrial socket outlet, 2-pole & earth, metal enclosed plug top, sheet steel enclosure, suitable to accommodate a 20 Amp SPN-MCB/DP, on surface or in recess, with chained metal cover for the socket outlet, complete with connections, testing and commissioning etc. as required.

Providing and fixing TP&N switch disconnector fuse unit panel mounting, 415/500 volts with 3 No. HBC/HRC fuses, open execution, including drilling holes in the cubical, making connections, etc. as required. 200 Amp. Category-A

Earthing with copper earth plate 600 mmx600 mmx 3 mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt ) complete as required.

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia. 300 mm long copper tube, having single prong at top, with 85 mm dia 3 mm thick copper base plate including holes etc. complete as required.

Supplying and fixing copper tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required ( for vertical run)

Supplying and fixing copper tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required ( for horizontal run)

Providing and fixing M.V.danger notice plate of 200 mm x 150 mm made of mild steel at least 2 mm thick, and vitreous enameled white on both sides and with inscription in signal red color on front side as required.

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, rmoured/ XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1 meter below the ground level including excavation sand cushioning, protective covering and refilling the trench etc. of the Armoured cable 4 sq. mm (twin core) for Yard lights.

Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and fixing of Nonreturn valve, Dead weight safety valve, 2 No C.P. connection rods 18" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. 25 Liter capacity water heater (Cat-A)

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. Ceiling Fan 1400 mm sweep, Category-A

Providing and installation of Exhaust Fan, Light duty, (Domestic) 225 mm sweep in the existing opening, including taking the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc.

Providing and fixing 1 x36 watt-LED Panel surface mounting /recessed type light fixture 60x60cms size syska/jaquar make.

Providing and fixing 6 watt recessed down light round shape for falce ceiling complete.

Supplying and fixing of fancy wall bracket containing thread type LED lamp holder (s) of all sizes and shapes, complete with all accessories but excluding LED lamp including making connections, testing etc. as required. Fixed type wall bracket 150 dia, single lamp.(Category-A)

Providing, Installation, testing and commissioning of prewired flourecent tube fitting 1x20W LED coplete in all respect.

Providing and fixing mirror light 60cms long 6 watt LED fixture.

Supplying and fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required

Supplying and fixing LED BULBS 9 watt suitable for D.C./A.C. single phase,230 volts complete as required

Supplying and drawing co-axial TV cable, RG-6 grade,0.7mm (75 Ohms) copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed, steel / PVC conduit as required.

Supplying and fixing bakelite batten/angle holder including connections etc. as required.

Supplying and fixing of integral LED Post Top Lantern of following capacity, cast aluminium spigot, spun aluminium canopy, opal acrylic diffuser, complete with all accessories but excluding CFL lamp including making connections, testing etc. as required. Gate post top lantern - CLED 22 watt.

Supplying and fixing of integral LED Boundary wall lights over G.I. pipe poll 1.20 mtr ht. 50mm dia 9 watt LED lamp with 200mm dia globe made of acrylic sheet complete.

Supplying and fixing stepped type Modular fan regulator on the existing modular box including making connections etc. as required.

Supplying and fixing of INTERCOME exchange of reputed brand having 20 connections with sets

Supplying and fixing of split type air conditioner Blue star/havells/carrier make having two stars features auto clean filter four wayu swing all copper pipes including making provision of draining of back moisture water through GI pipe 20mm dia electronic voltage stabilizer, cutting holes for conduits in wall, unit bracket set fixed on outer wall complete as required

2.00 Tonne capacity

Supplying & fixing of LED 32" Sony/Samsung/LG make

Supplying & fixing inverter with dual batteries of make Luminious

Supplying & fixing water purifier with container 25 ltrs capacity (Aquaguard Model MAGNA HD RO+UV)

Supplying & fixing washing machiner semi automatic double container 8.5KG capacity make kLoyd/Samsung/Whirpool/LG

Supplying and fixing Microwave Oven 23 ltrs make IFB.

Supplying and fixing Refrigator 320 ltrs capacity make Hairer/godrej/samsung/LG energy saving

WATER SUPPLY AND SANITARY Providing and fixing high pressure spigot and socket waste ventilating pipe of following daimeter i/c entire carriage of material within all leads and lifts.

75mm dia

100mm dia

Providing and fixing PVC plain bend of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

100mm dia

Providing and fixing PVC door bend of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

100mm dia

Providing and fixing PVC collar/ socket of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

100mm dia

Providing and fixing PVC Single equal brach of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

100mm dia

Providing and fixing PVC Single equal brach with oval access of following diameter i/c entire carriage of material within all leads and lifts.

75mm dia

100mm dia

Providing and fixing PVC Floor traps 110x75mm i/c entire carriage of material within all leads and lifts.

Providing and fixing viterous China wash down water closet (European Type WC pan) with intergral S” trap including jointing the trap with soil pipe in cement mortar 1:1 (1cement: 1 sand) including entire carriage of material within all leads and lifts.

Supplying and fixing single piece WC 300mm wall distance JaQUAR/CERA MAKE

Providing and fixing viterous China wash basin with single hole for mixure tap with C.I or MS brackets painted white i/c cutting holes and making good the same but excluding fitting i.c entire carriage of material within all leads and lifts CERAMake concord 630x450mm size.

Providing and fixing viterous China pedestal for wash basin complete recessesed at the back for the reception of pipes and fitting i/c entire carriage of material within all leads and lifts.

Providing and fixing of MI union for wash basin 32mm dia i/c carriage of material within all leads and lifts.

Providing and fixing 32mm dia PVC waste pipes for wash basin i/c brass check nut i/c entire carriage of material within all leads and lifts.

Providing and fixing 90x60cms. bevelled edge mirror of superior glass mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washer including carriage of materials within all leads and lifts.

Providing and fixing C.P. brass towel rail complete with C.P.brass brackets fixed to wooden plugs with C.P. brass screws including carriage of materials within all leads and lifts 600 x 20mm.

Providing and fixing 600x120mm glass shelf i/c entire carriage of material within all leads and lifts.

Providing and fixing CP toilet paper holder i/c entire carriage of material within all leads and lifts.

Providing and fixing CP brass soap dish i/c entire carriage of material within all leads and lifts.

Providing and fixing Tooth brush and tumbler holder i/c entire carriage of material within all leads and lifts.

Providing and fixing CP brass shower 300mm dia,with 60 cms long rod, i/c entire carriage of material within all leads and lifts.

Providing and fixing brass bib tap long nose 15 mm dia (Heavy duty) i/c entire carriage of material within all leads and lifts.

Providing and fixing CP brass wall mixture for bathing area within all leads and lifts.

Providing and fixing brass angle valve 15 mm dia without nut and pipe i/c entire carriage of material within all leads and lifts.

Providing and fixing CP concealed stop cock 15 mm dia without nut and pipe i/c entire carriage of material within all leads and lifts.

Providing and fixing single hole single lever wash basin mixture i/c entire carriage of material within all leads and lifts.

Providing and fixing PVC connection 15mm dia i/c entire carriage of material within all leads and lifts.

Providing and fixing 100mm dia, C.P. brass grating including carriage of material within all leads and lifts.

Providing and fixing Jet connection ,health facut ,fixed for WC seat i/c entire carriage of material within all leads and lifts.Jaquar.

Providing and fixing CP towel ring i/c entire carriage of material within all leads and lifts.

Providing and fixing CP towel rack 600x250mm for VIP toilet i/c entire carriage of material within all leads and lifts.

Providing and fixing wall to ceiling and floor galvanised mild steel tubes light grade), tube fittings and clamps i/c making good wall ceiling & floor of following diameter i/c entire carriage of material within all leads and lifts

15mm dia

20mm dia(ALL INTERNAL FITTING OF TOILETS)

25mm dia

Providing & fixing Brass full way wheel valve i/c entire carriage of material within all leads & lifts

15mm dia

20mm dia

25mm dia

Providing and fixing 115x50x25cms size double bowl of approved make stainless steel kitchen sink i/c entire carriage of material within all leads and lifts.

Providing and fixing 1000 ltrs. Double layer sintex make water storage reservoir with top lid and making connection complete in all respect including all leads and lefts.

Constructing manhole with RCC top slab in 1:2:4 mix ( 1 cement :2 sand:4 graded stone aggregate 20 mm nominal size) foundation concrete 1:4:8 ( 1cement:4sand :8graded stone aggregate 20 mm nominal size),inside plastering 15 mm thick with cement mortor 1:3 (1cement:3sand),finished with a floating coat of neat cement & making channels in cement concrete 1:2:4 (1cement:2 sand:4 graded stone aggregate 20mm nominal size) finished smooth complete i/c curing & testing (i) inside size 1200 x 900 x 1000 mm deep i/c c.i. cover with frame (m. duty) with single pattern 455 x 610 mm internal dimensions (total wt.of cover & frame to be not less than 38 kg) 23 cms. thick brick masonry walls using 2nd class brick in cm 1:3 (icement : 3 sand)

Providing & fixing stone ware gully trap grade 'A' complete with CI grating, B/Masonry chamber in cement mortor 1:5 & water tight CI cover with frame of 300 mm x 300 mm size (inside). The wt.of cover to be not less than 4.53 Kg & frame to be not less 2.72 Kg. (Square mouth traps 100 x 100 mm size)

Supply four sets of structural design and drawing of village water sanitation committee center duly vetted from reputed institution i.e. NIT Hamirpur/PEC Chandigarh etc. alongwith soil bearing capacity report complete in all respect .

Dinesh Kumar Sharma

Subham Mahajan

PAWAN KUMAR RANA

SANJAY VERMA GOVT. CONTRACTOR