Special repairs to Bldg No T-104 and T-105 at Mil Stn Beas under GE Kapurthala

Amount

Demolition of cement concrete in ground floor and paving n. exc. 15cm thickness (below or above ground level) complete all as specified and directed.

Material & labour for 75mm thick PCC (1:3:6) type C-1 ( using 20mm graded stone aggregate) as in plinth protections and path etc finishing the concrete surfaces even and smooth without using extra cement & joint filled with bitumen sand mixer 1:2 complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work & precast concrete articles complete all as specified and directed.

Material & labour for brick work with sub class 'B' bricks, old size, straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar (1:6) complete all as specified and directed.

Taking down cement plaster/ terrazzo cast in situ of any description thickness including racking out joints hacking for key, scrubbing down with water etc. and removing rubbish complete all as specified and directed.

M&L for 10mm thick cement plastering in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick cement plastering in cement mortar (1:6) of brick work or concrete surfaces with using water proofing compound finished even & smooth without using extra cement complete all as specified and directed. Note: WPC will be measured and paid separately

M&L for applying two coats of cement base paint on newly plastered or unplastered surfaces including preparation of surfaces complete all as specified and directed.

Material & labour for preparation of newly plastered surface of walls and applying two coat of oil emulsion distemper over one coat of alkali resistant primer complete all as specified and directed.

Dismantling of AC roof covering sheets complete all as specified and directed.

Supply & fix pre painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

Supply & fix pre painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) of any thickness incl cover fillets etc complete all as specified and directed.

Material & labour for ceiling using 9 mm thick gypsum based ceiling tiles with weather resistance face on back side and vinyl finish on the front fixed in 24mm GI frame work of grid 600mm x 600mm size, members of snap grid frame work of GI/Steel section of 24 mm wide with T flanges, channels etc of white colour having rotary stitching on all members i.e. main runner, 1200mmx600mm cross tee galvanised with minimum thickness of 120 gms/sqm passed through 500 hrs test and hanging the same with existing roof members such as rafters, purlins or other wooden members particularly provided for hanging purpose using 8 mm dia mild steel bar of required length fixed with nut bolt 50 mm long and 10mm dia of neck with washer flat iron 50x6mm thick clamps etc to wooden members complete all as specified and directed.

Dismantling framed trusses of span not exc. 10m complete all as specified and directed.

Dismantling mild steel work of any description complete all as specified and directed.

Erection and fixing only mild steel work in tubular trusses/purlins /rafters with special shaped washer etc.complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St.-240 complete all as specified and directed.

Erection and fixing mild steel rolled section as in roof trusses (framed), trussed, purlins, crane grantries, rails and fastening and heavy brackets framing (Beam, tee, channel or flat section) includng distance pieces cleats etc conforming to Fe-410-W. Gde-E-250 including one shop coat of zinc chromate primer paint a (incl preparation of surface) before fabrication all as specified and directed.

Supply and fix rolled MS work as in angle, joist, channel or tee sections fixed independently,without connecting plates (cut to ordinary lenghths i.e. within 20mm of length indicated) Fe-410 Gde- E-250) complete all as specified and directed.

Material & labour for preparation of old steel surfaces of any description, over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed.

Material & labour for preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply and fix mild steel work in tubular trusses/purlins /rafters including provn of new nut bolts special shaped washer etc.complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St.-240 complete all as specified and directed.

Supply and fix rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes with riveted, bolted or welded attachment etc conforming to Fe 410-W (Gde E-250) quality - A complete all as specified and directed.

Material & labour for welding in repair not exc.2.5 cm in length for thickness of metal not exc.6 mm thick complete all as specified.

Material & labour for cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) as in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands plinth cources, roof kerbs or mud stops, benching, coping, bed plates, parapets, water throughs and the like etc including weathering, slightly rounded or chamfered angles throating etc complete all as specified and directed.

Material & labour for mild steel high yield strength TMT bars 10 mm dia and over cut to length bent to shape required, including cranking, hooking ends, bending and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Material & labour for mild steel high yield strength TMT bars 6 to 8 mm dia cut to length bent to shape required, including cranking, hooking ends, bending and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Taking down chowkhats or frame with shutter (with or without taking off shutter from the frame) area exc 1.5 Sqm but n. exc 4 sqm each for doors and windows complete all as specified and directed.

Taking down chowkhats or frame with shutter (with or without taking off shutter from the frame) area n exc. 1.5 Sqm each for doors and windows complete all as specified and directed.

Supply and fix mild steel framed work as in doors chowkats or frames, cooler stand or other section with gusset plates, rails, braces, etc. using steel conforming to Fe-410 Gde-E-310 complete including drilled for fixing of steel sheeting or other covering; doors, door frames, chowkhats etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing including necessary cutting drilling and welding etc complete all as specified and directed.

Supply and fix 35mm thick 2nd class hardwood factory made plain framed, panelled shutters (any no. of panels), with lock rail and panels of 9mm thick BWP commercial ply or of venered particle board 12mm thick with commercial veneering on both faces with rails and style of 2nd class hard wood. The size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fix 2nd class hard wood factory made glazed and skeleton shutters 30mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in clause 8.24 (a) of SSR Part-I; supplied and fitted to chowkhats complete all as specified and directed.

Supply & fix MS pressed handles, oval type, stove enameled black 150mm size complete all as specified and directed.

Supply & fix MS barrel tower bolt ISI marked 200mm long stove enameled black with bright bolt and fixed complete all as specified and directed.

Supply & fix 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed.

Supply & fix mild steel sliding door bolts 250mm long stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

Supply & fix mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply & fix Steel windows 1.25 mm thick Box type (primer coated) ERW hollow ‘P’ section of size 60mm x 25mm single rebated comprises of glazed skeleton shutter EWR Sec 50mmx20mm and 1mm thick and two open able leaf consisting two Nos sash bar of ‘T’ section 20mm x 3mm complete welded to frame with one vertical mullion of EWR box type ‘T’ section of size 60mmx25mm and 1.25mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B1 using 20mm graded stone aggregate including following fittings welded to framed shutter :- (a) Holdfasts 150mm long 12mmx3mm made to shape per window -04 Nos, (b) Handle of Z Sec 20mmx25mm, 100mm long per leaf-01 No, (c) MS tower bolt 150mm long per leaf -02 Nos, (d) ‘Z’ sec 20mm x 25mm, 100 long stopper per leaf -01 No, (e) Cleat 55 mm long of hollow square 15mmx20mmx63mm welded to hinges per leaf -01 No, (f) MS pintal hinges of size 75mmx12mm per leaf -02 Nos, (g) Fabrication and fixing arrangement as per drawing No CEJZ/TD/1019, Sh 1/3 to 3/3 and No. CEJZ/TD/1020, Sh 1/3 to 3/3. Note : Glass, grills & painting shall be measured & paid for separately and irrespective of whatever shown on drgs, MS grills shall be of 12 mm dia MS square bar.

All as per srl item No. 38 here in before but of gauged shutter. Note for item No. 38 & 39 :- Drg No. CEJZ/TD-1019 & 1020 are not being uploaded and the same can be seen in office of CWEJRC on any working day. Wire gauge, grill & painting shall be measured and paid for separately

Supply and fix 4 mm thick sheet glass ordinary quality, pinhead type and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and avarage width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-charge.

Material & labour for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Supply & fix floor door stopper 140mm long aluminium alloy body anodized with hard drawn steel spring complete all as specified.

Dismantling floor, hearth or wall tiling/ china moisac including cement mortar bedding (but not backing), removing rubbish off outside MD land complete all as specified and directed.

Material & labour for 100mm thick PCC (1:2:4) type B-2 (using 40 mm graded stone aggregate), as in leveling concrete in floor finished even & rough to receive top floor layer/finish complete all as specified & directed.

Material & labour for 20-25 mm thick machine cut kota stone slab 550mmx550mm/600mmx600mm laid in floors, slabs and steps etc jointed with grey cement slurry mixed with pigments to match the shade of the slab including cutting, rubbuing and polishing over and including screed bed 20mm thick in cement mortar (1:6) complete all as specified and directed. Note - Kota stone for step shall be in single piece.

Material & labour for 20-25mm thick machine cut kota stone slab as in vertical surfaces such as dado/ skirting/pillars/risers of stair case etc jointed with grey cement slurry mixed with pigments to match the shade of the slab including cutting, rubbuing and polishing over and including rendering 15mm thick in cement mortar (1:4) complete all as specified and directed. Note - Kota stone for risers of step shall be in single piece.

Material & labour for granite (of any type) work, 20mm thick machine cut (table rubbed and polished) in steps jambs, pillars, window cills, cooking platforms, shelves in cupboard, handwash places and like including necessary cutting and grooving to walls and making good including 15mm thick in cement mortar (1:3) screed bed or bedding layer and pointing with cement mortar (1:2) with admixture of pigment to match with shade of granite complete all as specified and directed.

Material & labour for hard core of broken stone or boulder of gauge n. exc. 63mm, deposited, spread and levelled in layers n.exc. 15cm thick, watered and well rammed to a true surface complete all as specified and directed.

Material & labour for 100 mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in sub base of footpath surface channels etc complete all as specified.

Material & Labour for 60mm thick machine pressed precast concrete interlocking paver block and shape and size confirming to IS 15658-2006 of M-35 Grade with grey cement and pigment over sand cushioning complete all as specified and directed. The Interlocking Paver blocks shall be procured directly from one of the Manufacturers specified. Note:-The sample shall be got approved from the GE before bulk procurement and lots shall be got tested independently by the GE.

Material & labour for sand filling under floors, paver blocks including watering and consolidation complete all as specified and directed.

Material & labour for 25mm dia mild steel pipe curtain rod, powder coated fixed with & including MS powder coated hooks/ brackets and decorative finials (at both side), curtain rings (minimum 5 Nos rings per running mtr of curtain rod) shade as approved by GE complete all as specified includng fixing of long size rawl plugs in wall for MS hook including taking out the existing old pelmet box along with old curtain rods complete all as specified and directed.

Taking down carefully existing point wiring of any type (i.e. wooden surface conduit casing capping or concealed conduit) complete for light or fan or socket or power etc on wooden batten or in conduit including fittings and accessories like switches, sockets, wooden board and making good disturbed portion to match with existing complete all as specified and directed.

Material & labour for concealed point wiring complete with single core 1.5 Sqmm (nominal area) PVC insulated and unsheathed cable 1100 volts multistranded, copper conductor cable (FRLS) drawn through and including PVC concealed conduit not less than 20mm dia bore medium grade (ISI marked) and accessories like bends, tees, junction boxes etc, fix on wall or ceiling surfaces all as specified including 1.5 sqmm , FRLS, copper multistranded cable as earth wire including sunken pressed steel terminal boxes and bakelite white/ coloured top sheet cover 3.0 mm thick , for One light point / fan point controlled by one way switch complete all as specified and directed.

All as per item No. 55 above but for 3 pin socket out, 5 amps on same board complete all as specified.

All as per item No. 55 above but for 3 pin socket out, 5 amps on independent board complete all as specified.

All as per description of srl item No 55 here in before but using 2.5 sqmm (nominal area) PVC unsheathed cable independent including PVC cable copper conductor with 2.5 Sqmm PVC insulated copper cable for continuous earth continuity conductor and connecting for earth dolly for 3 pin socket out let 15 Amps on independent board. complete all as specified and directed

S&F switch piano flush type 5 amp single pole one way complete all as specified and directed.

S&F switch piano flush type 15 amps single pole one way complete all as specified and directed.

Supply and fix socket out let multi purpose, 5 pin, 5 amps flush type complete all as specified.

Supply and fix socket out let multi purpose 2 in one, 3 pin, 5 & 15 amps flush type complete all as specified.

Taking down old unserviceable FTL fittinng 36/40 watt and Supply and fixing surface mounting energy saving LED tube light fitting/batten with LED T8 tubelight with PC body, 1x20W, 230V , light distribution lumen output should be at least 1800 lumen with a CCT of 6500K, power factor should be greater than 0.9 with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 all as specified and directed. Make: Crompton battencat part No. DMLN1LT8-16 & LED cat part No. LT8-20-865-2 or equivalent make as mentioned in group 1 of Appx "B"

Taking down old unserviceable MCBs and supply and fixing MCB 6 to 32 amps, SP 240 volts, B series complete all as specified and directed. Make: C&S electric product code CSMBS1B6 to CSMBS1B32 or equivalent make as mentioned in grp 1 of Appx "B"

Taking down unserviceable MCBs and S&F MCB single pole & neutal, 6 to 32 Amps 240 volts complete all as specified and directed. Make: C&S electric product code CSMBS1B6N to CSMBS1B32N or equivalent make as mentioned in grp 1 of Appx "B"

Supply and fix in repairs sheet metal enclosures for DB's, detachable gland plates flush mounting for MCBs fitted with bus bar double door earth wire and neutral link, 8 ways 240 volts complete all as specified and directed.

Supply and fix in repair ceiling rose surface type bakelite 65 x 50 mm three terminal PVC / Polycarbonate isolated body(ISI marked) complete all as specified.

S&F in repair angular lamp holders, with PVC insulated body with back plate suitable for batten fittings including 01 No. of LED 1 x 09 Watt, 230 Volts suitable for 230 volt AC complete all as specified and directed. Make : Havells LED cat part No. LHLDEUHEMC8R009 or equivalent make as mentioned in grp 1 of Appx "B"

Taking down ad refixing ceiling fan of any sweep including connecting up incl provision of twin core twisted flexible copper conductor cable of suitable sizefrom ceiling rose/connector to fan and GI pipe of suitable size/Steel rod, clamps, hooks, nut bolts etc as reqd on site complete all as specified.

Supply and fix fan regulator, electronic step type, five steps socket type single phase, including connection complete all as specified and directed.

Material and labour for earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr deep below normal ground level connected to GI earth wire 4 mm dia connected to earth plate by means of nut, bolts, check nut & washer of galvanized iron or of steel, GI earth wire will be protected by 15 mm dia GI pipe 'light grade', watering pipe 20 mm dia GI 'light grade', GI wire meshed funnel, alternate layer of char coal and salt on all side to earth plate upto thickness of 150 mm, filling of black cotton soil in earth pit upto ground level, PCC chamber recessed for and including RCC cover including all necessary excavation & earth work, earth wire connected to O/H continuous earth wire on pole, testing the earthing after completion including taking out old earthings complete all as specified and directed. Note :- (I) Earth pit shall be constructed 50cm from the side of excavation to avoid sinking of pit (II) PCC chamber shall be (1:3:6) using 20mm graded stone aggregate and 50mm thick RCC (1:2:4) type B-1 cover slab reinforced with 8mm dia TMT steel bars @ 100mm c/c both ways complete all as specified and directed. .

Disconnecting and taking out old u/s cable of service connection/submain of any size and type from pole to DBs/main switch complete all as specified and directed.

Supply and fixing in replacement sub main wiring with two single core PVC insulated cable with copper conductor stranded and sheathed of size 6 sqmm, two runs in and including PVC concealed conduct medium grade of size not less than 25mm dia including PVC accessories complete incl cutting and chasing and making good etc incl one run of 6 sqmm PVC insulated unsheathed multi stranded copper conductor cable to common earth and connected to earth dolly complete all as specified and directed. Note: Two runs of 6 sqmm & one run of 6 sqmm cable with 25 mm PVC conduit shall be measured as one unit

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth in soft/loose soil for laying of cable/GI pipe and getting out complete all as specified and directed.

Returning filling in including spreading,levelling,watering, well ramming in layers not exc 25 cm each complete all as specified and directed.

Removal of surplus soil to a distance not exc 50 m and deposited where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

M&L for brick protection using old size sub class 'B' bricks, laid flat dry but adjoining to each other laid length wise perpendicular to the axis of cable complete all as directed and directed

Supply and spread river sand in trenches as cable cushioning 8 cm below the cables and 15 cm above the cables complete all as directed and directed. Note : Punned down thickness shall be measured.

Supply, laying and testing LT cable XLPE/PVC insulated armoured and with aluminium conductor 1100 volt grade 16 sqmm 2 core laid in trenches in floor, in ducts, through pipe or fixed along the pole complete all as specified and directed. Note:- 1. Excavation, earth work, sand cushioning, and brick protection shall be measured and paid for separately. 2. Rate of necessary lugs, thimbles and jointing material shall be included in unit rate.

Supply and fix LED building security light fitting 15 watt, powder coated pressure die cast aluminium compact LED security light including 1.5 mtr long 40mm dia GI pipe mounting bracket made to shape for fixing on wall with 40mm x 6mm flat iron clamp 02 numbers with 16 mm dia bolts, nuts and washer and Contractor shall provide 2 years written manufacturer's warranty for the LED fixture complete including driver from the certified date of completion complete all as directed and directed. Make: Crompton cat part No. LSTS-15-CDL or equivalent makes as in group 1 of Appx 'B'

Supply and fixing in repairs GI pipe 40mm dia light grade galvanised with all fittinng laid in trenches/on pole/road crossing etc for cable protection complete all as specified and directed.

G M BUILDERS 36

DUGGAL CONSTRUCTION CO

M/s Rajmani Engineers