Special repair to Bldg No. 302, addn/altn to certain bldg at Air Force Station Jaisalmer

Amount

Taking down chowkhats or frame with shutters (without taking off shutters from the frames), area exceeding 1.50sqm but not exceeding 4.00sqm each complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frames), area not exceeding 1.5 Sqm each complete all as specified.

Taking down cement plaster or cement lime plaster of any discription on brick wall or stone wall or ceiling etc. including raking out joints hacking for key scrubbing down with water etc. complete all as specified and directed.

Demolition of brick work or stone/boulder/PCC block masonry built in cement mortar including all quoins, arches, pillars, etc. and including ashlar facings, dressed stone work and precast concrete articles like paver blocks laid dry manhole cover and removing rubbish off the premises etc. complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) as in ground floors, copings and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

Dismantling AC sheet (Corrugated, Semi corrugated etc) as in roof coverings etc complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

Excavating in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation etc or for shafts, wells cesspits, manholes, pier holes etc or not exceeding 10 sqm on plan and not exceeding 1.5m in depth and getting out in any type of soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick etc. complete all as specified and directed.

Earth filling under floors with available approved soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removal of excavated soil/ material/surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.50m above the starting point complete all as specified and directed.

Excavating in post holes (or similar holes) each not exceeding 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance not exceeding 50 m and making good surface in soft/ loose soil complete all as specified.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall below concrete apron using chemical emulsion at the rate of 2.25 litres per linear metre including drilling and plugging holes etc in apron complete all as specified and directed.

Post construction anti termite treatment soil under chemical existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortor 1:2 to match the existing floors complete all as specified and directed. Note:- Measurements to be paid shall be portions of area where holes are drilled and treated only.

Anti termite treatment at points of contact of wood work by chemical emulsion (in oil or Kerosene based solution) @ 0.50 litre per hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

Hardcore of guage not exceeding 63mm deposited spread and leveled in layers not exceeding 15 cm thick watered and rammed to a true surface complete all as specified and directed.

Plain cement concrete (1:4:8) Type D-2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

Plain cement concrete (1:2:4) Type B-1 (using 20 mm graded stone aggregate) as in surface channels and drains and other similar items, including necessary formwork complete all as specified and directed.

Providing plain/reinforcement cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) cast-in-situ as in coping, plinth courses, kneelers, apex, stones, bed plates, water through, kerbs and the likes including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

Squared rubble walling Jodhpur type brought upto courses, well bonded, bedded and solidly hearted, built in cement and sand mortar (1:6) complete all as specified and directed.

Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted stone masonry built in cement and sand mortar 1:6 but except stone complete all as specified and directed.

Extra over stone walling for hammer dressing with maximum dipression on face from sraight edge not exc 20mm and dressing to face stones, face beds and joints as specified to squared rubble walling, jodhpur type, brought upto courses complete all as specified and directed.

Keyed pointing in cement mortar 1:4 to random or polygonal rubble walling, uncoursed or brought upto course stone masonry all as specified & directed.

Precast cement concrete (1:3:6), type C-1 (using 20 mm graded stone aggregate) as in solid block masonary exceeding 10cm and setting in cement and sand mortar (1:6) complete all as specified and directed.

Precast RCC 1:2:4 type B1 using 20mm graded stone aggregate as in cover slabs of drains, manholes, chajjahs water troughs, mangers, shelves and similar articles with plain faces including use and waste of formwork and and setting in cement and sand mortar (1:6) complete all as specified and directed.

50mm thick Precast cement concrete (1:2:4 type B0 using 12.5mm graded crushed stone aggregate) as in decorative shaped and intricate design as approved by users louvers and jallies, including all mouldings but excluding frame, setting in cement and sand mortar 1:6 including dismantling of old unserviceable jallies all as specified & as directed.

20mm thick granite (or any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

Factory made Second class hard wood 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) etc complete all as specified and directed.

Factory made 30mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

Butt hinges of size 100mm, heavy weight, cold rolled mild steel ISI marked complete all as specified and directed.

125mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

Extruded aluminium alloy handle, D type, 150mm size, fabricated type, anodized (ISI marked) complete all as specified.

Mortice lock brass, vertical type, size 100mm 4 lever complete all as specified and directed.

Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, with & including replacement of floor tiles if any broken during repair work and making good surfaces matching to the existing surfaces in repair complete all as directed.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium snap beading complete all as specified and directed.

Dismantling mild steel work of any description as in covers to cable ducts, rafters, purlins etc complete all as specified and directed.

Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, flat iron fillets (for securing wire mesh) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Gde E-165 (Fe-290) complete all as specified and directed.

Mild steel work in framed work such as grills, gratings, framed guard bars etc. with ends of bars shouldered and/ or riveted, or forged into spikes, and in ladders, railings, frame of water tank etc.and similar work confirming to Fe- 290 Grade E-165 for framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc. complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exceeding 5cm long and dia of neck 5 to 10mm complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild steel rolled sections as in column, vertical posts, main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle iron cleats or other connecting plates etc. conforming to Gde E-250 (Fe 410-W) quality `A’ complete all as specified and directed.

Anodised aluminium extruded sections as in frames for doors, windows, ventilators, partitions, expanded metal mesh, with one or more rebates including necessary joining cleats, glazing clips, rubber neoprene packing for fixing, anodised aluminium snap beading screws etc complete all as specified and directed.

Anodized aluminium sections as in window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and as directed.

Mild steel work in butular trusses, tubular rafters, stanchions and purlins trusses, tubular pipe sections as in main and cross beams, hip and jack rafters, purlins including special shaped washer etc complete using ERW or induction butt welded tubes necessary welding, bolting, special shaped washer, clamps, cleats Fe-290 (Gde E-165) complete all as specified and directed.

12mm thick medium density fibre board, exterior grade, fixed to wall of required size with screws as in wall linings as in repair complete all as specified and directed.

0.90mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed to MDF boards in required sizes with approved adhesive as per manufacturer's instructions complete all as specified and directed.

6mm thick PVC Pre laminated Gypsum Board/tiles of size 600mmx600mm for ceiling including Gl snap grid frame work powder coated for false ceiling including dismantling and taking down old unserviceable false ceiling complete all as specified and directed/manufancturers specifications. Note: Rates for GI snap grid frame work powder coated included in unit rate in this item. No extra cost shall be admissible for GI frame work.

Machine cut kota stone flooring 20-25mm thick laid in floors in squares or rectangular pattern over and including 15mm thick cement screed bed in cement and sand mortar (1:6) set and jointed neat cement slurry and pointed in coloured cement to match the shade of the slab including rubbing and polishing complete all as specified and directed.

75mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection and flooring complete all as specified and directed).

75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

100mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of flooring/ hard standing/paving finishing cement concrete surface fair and even complete all as specified and directed.

100mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in flooring, finished even and smooth with using extra cement complete all as specified and directed).

1.50mm thick 38mm wide plastic dividing strips fixed in concrete floors etc complete all as directed and specified. complete all as specified and directed).

Dismantling of floor, hearth or wall tiling, stone partitions including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

Coloured anti Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc over 15mm thick in cement and mortar (1:6) bedding set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed

Coloured glazed ceramic tiles in dado/skirting 450x300x7mm thick on vertical surfaces, dado and skirting over and including 10mm thick cement and sand mortar (1:4) backing coat set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tile complete all as specified and directed

Vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed

Vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved) on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and directed

Machine pressed factory made coloured rubber moulded precast concrete inter locking paver block, 60mm thick, M-35 grade any shape and size with grey cement with pigment wih ISI Marked conforming to IS-15658-2006 and including 25mm thick machanicaly compacted thickness of sand bedding below pavar tiles laid to required level & slope complete all as specified and directed.

15mm thick plaster in cement and sand mortar (1:6) on other than or fair face of brick work or concrete surfaces or stone masonry surfaces of wall, finished even and smooth without using extra cement complete all as specified and directed.

15mm thick plaster in cement and sand mortar (1:4) on stone masonary surface or fair face of concrete surfaces of wall, finished even and smooth without using extra cement complete all as specified and directed.

10mm thick plaster in cement and sand mortar (1:6) on stone masonary surface on fair face of concrete surfaces of wall complete all as specified and directed.

10mm thick ceiling plaster in cement and sand mortar (1:3) on uneven faces of concrete surfaces, on fair of ceiling and finished even and smooth without using extra cement complete all as specified and directed.

Preparation of old decorated surfaces of ceilings of any description and applying one coat of white wash complete all as specified and directed.

Preparation of old painted plastered or unplastered wall surfaces of any description and applying one coat of oil bound distemper paint complete all as specified and directed.

Preparation of old painted plastered or unplastered surfaces on wall and applying one coat of cement based paint complete all as specified and directed.

Preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed.

Prepariation of newly or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Complete removal of existing treatment, filling up undulation and applying one layer of ready mixed wall putty on entire surface of wall/ceiling to smooth finish surfaces with appropriate sand paper and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

Preparation of newly plastered surfaces and applying one layers ready mixed wall putty on entire surface of wall/ceiling to smooth finish surfaces with appropriate sand paper and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

Preparation of newly plastered or unplastered of wall surfaces and applying two coats of cement based paint as approved complete all as specified and directed.

4mm thick sheet glass ordinary quality and glazing with oil putty not exceeding 0.50 sqm in each pane including Hacking out broken glass (any thickness, size, quality or description) from wooden/steel or stone, concrete or brick surrounds, glazed with putty or fixed with beads and fixing new ones complete all as specified and directed.

15mm bore fancy type chromium plated two way angle cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Galvanized steel water tubing medium grade of 15mm bore with & including all fittings and complete to walls and ceiling or laid in floors, including taking up or down old unserviceable steel water tubing and connections of 15mm bore, complete all as specified and directed.

Galvanized steel water tubing medium grade of 20mm bore with & including all fittings and complete to walls and ceiling or laid in floors, including taking up or down old unserviceable steel water tubing and connections of 20mm bore, complete all as specified and directed.

15mm bore fancy type chromium plated Bib taps, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed and including taking down old unserviceable complete all as specified

15mm bore fancy type chromium plated swan neck pillar taps with capstan heads, screwed down high pressure with long screwed sharks and fly nuts screwed down for iron pipes in repair complete all as specified and directed.

15mm bore fancy type chromium plated Stop valves/angle cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and directed.

15mm bore fancy type chromium plated push valves/angle cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and directed.

15mm bore stop valve fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union and including taking down old unserviceable valve complete all as specified and directed.

20mm bore Gun-metal globe or gate valves (ISI marked), with iron wheel head, screwed both ends for iron pipe and fixed in repair complete all as specified.

Chromium plated Hand Shower (Health Faucet) with 1.0 to 1.50 metre long flexible tube & wall hook and anodised hanging device complete all as specified and directed.

Chromium plated Jet spray with flexible tube 1.0 to 1.50m length complete all as specified and directed.

PVC (SWR) floor trap dia of outlet 75mm, with grating including jointing with solvent cement for trap in repair complete all as specified and directed.

110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls in repair complete all as specified.

75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls in repair complete all as specified and directed.

110mm bore PVC (SWR) bend any radius provided with access door in repair complete all as specified and directed.

75mm bore PVC (SWR) bend any radius provided with access door in repair complete all as specified and directed.

110mm bore PVC (SWR) Junction single (Single T) equal or unequal provided with access door in repair complete all as specified and directed.

PVC connection suitable for 15mm bore with PTMT nuts of 600mm length and including taking down old unserviceable complete all as specified and directed.

100mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, laid in trenches or floors including taking down old unserviceable pipe complete all as specified and directed.

100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door including taking down old unserviceable complete all as specified and directed.

100mm cast iron Nahani trap, grating including jointing to waste pipes with lead joint fixed in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate complete all as specified and directed.

PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150mm bore pipe complete all as specified and directed.

Salt glazed stone ware drain pipes of 150mm bore, (ISI marked), laid and jointed with collars and including demolition and beaking up 150mm bore drain pipes set in cement mortar including PCC haunching and bedding complete all as specified and directed.

Cutting into existing manholes/septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 (using 20mm stone aggregates) smooth finished and reforming benching as required for 150mm bore pipe complete all as specified and directed.

Cutting holes into or through brick/stone masonry wall built in cement mortar and making good in cement and sand mortar 1:3 or PCC 1:2:4 type B0 as required for superficial area exceeding 400 sqcm but not exceeding 0.25 sqm complete all as specified and directed

Sinks with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm, bowl size 410mmx330mmx160mm including taking down old unserviceable complete all as specified and directed.

Vitreous china wash down water closet pan (Pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic water closet seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device in repair complete all as specified and as directed.

Vitreous china wash hand basin white flat back of size 580x450mm with including a pair of cast iron brackets embedded in PCC 1:3:6 type C-1 blocks of size 10x7.5x15 cm with and including 32mm size brass chromium plated waste coupling with long screwed shanks and fly nuts flange fixed including taking down old unserviceable complete all as specified and directed.

Vitreous china urinal, full stall type, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60mm long brass screws, pointing around urinal back in cement, with & including grating and union for discharge pipe and including dismantling and taking down old unserviceable complete all as specified.

Vitreous china wash oval type hand basin white under top of size 550x400mm including PVC discharge pipe and 32mm size brass chromium plated waste coupling with long screwed shanks and fly nuts flange fixed complete all as specified.

High/low level flushing cistern of syphonic action type 10 ltrs capacity PVC valve less fixed to wall with bracket and screwed including PVC flush pipe, white with inlet, ball valve float and handle including brackets complete all as specified and directed.

Jodhpur/Jaisalmer stone slabs as in drain covers to existing storm water drain self faces 7.5cm to 10cm thick and of drain width hoisted and set jointed and grouted in cement mortar 1:6 complete all as specified and directed.

Jodhpur/Jaisalmer stone slabs 20-30mm thick dressed true and square laid as in paths jointed and pointed in cement mortar 1:6 with and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Jodhpur/Jaisalmer stone slabs 15-20mm thick dressed true and square/rectangular tiles of approved sizes as in wall/column cladding/linings jointed and recess pointed in coloured cement mortar 1:6 with and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Point wiring for one light point controlled by one, one way 5/6 Amp switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including non metalic rigid PVC conduit 20mm dia with accessories fixed to cutting chases in walls by cutter and making good surface in cement and sand mortar 1:3 and to the original specification and PVC conduit on ceiling for steel structure/surfaces conduit with clamps, gutties etc for RCC ceiling with including cast iron/pressed steel/wooden terminal boxes (as per site requirement) including providing new 3mm thick plastic laminated sheet cover (Hylem) and including taking down old unserviceable point wiring complete all as specified and directed. Note : (i) Unit rates quoted by contractor shall be deemed to included for cutting chases in walls, ceilings and making good surfaces in cement and sand mortar (1:3) and finishing the surfaces to match with existing surfaces. (Make : Hylem/Anchor/Formica including machine screws and washer etc for fixing switches sockets etc including 1.5 sqmm copper conductor, standard (green colour earth), PVC insulated unsheathed earth wire to commen earth and connected to earth dolly as specified and directed.

All as per serial item No. 115.00 here-in-before but for one fan point controlled by one switch and regulator.

All as per serial item No. 115.00 here-in-before but for one 3 Pin, 5/6 Amps, socket outlet controlled by one 5/6 Amps switch on independent board.

All as per serial item No. 115.00 here-in-before but for one 3 Pin, 5/6 Amps, socket outlet controlled by one 5/6 Amps switch on same board.

Switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts (ISI Marked) in repair complete all as specified and directed.

Socket outlet, 2 in 1, 3 pin, 5/6 Amp, flush type, (ISI Marked), 240 Volts in repair complete all as specified and directed.

Ceiling rose surface bakelite 65mmx17.5mm with two or three terminal PVC/Polycarbonate, isolated body (ISI Marked) in repair complete all as specified and directed.

Lamp holder, PVC / Polycarbonate type (angle/batten) with back plate suitable for batten fittings, in repair complete all as specified and directed.

Prewired Distribution Board factory made sheet metal enclosure double door distribution board class IP-43 IK 09 with 200 Amps rated copper bus bar 240 Volts, 8 way, SPN DB, suitable for fixing MCB as outgoing and MCCB Triple Pole 100 Amp, rupturing capacity 25 kA as main incoming duly painted including fixing of lugs in main incoming and outgoing line and fixing of cable glands of suitable size including grouting the same in wall by means of nut bolts, angle iron and making good distrurbed surfaces including taking down old unserviceable complete all as specified and directed.

Sub main wiring with 2x4.00 sqmm, single core, PVC insulated unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) 1100 volts grade conforming to IS 694 including and 4.00 Sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke (FRLS) cable 1100 Volt grade as continuous earth wire in green colour including drawn through in 25mm dia PVC conduit including taking down old unserviceable submain wiring complete all as specified and directed. Note : Two run of 4.00 sqmm cable and one run of 4.00 sqmm cable as earth wire continuity conductor and one run 25mm dia PVC conduit shall be measured & paid as one unit.

Ceiling Fan 1200mm sweep, Single Phase, AC supply, 240 Volt, including canopies, three number blades, down rod, double ball bearing with capacitor of 2.5 mfd, and including PVC insulated PVC sheathed copper conductor flexible 3 core cable 23/0.0076 from ceiling rose or connector to fan including marking of MES number including taking down old unserviceable fan complete all as specified and as directed. (Note : Length of suspension rod shall be adjusted by cutting, threading as directed and its cost is deemed to be included in rate of hanging of ceiling fan).

Exhaust Fan 300mm sweep, BEE approved, ISI Marked with mounted in suitable opening arrangement with louvers and shutters suitable for operation on 240 volts, Single Phase, AC supply and connecting upto including three core PVC insulated PVC sheathed copper conductor flexible cable 23/0.0076 from ceiling rose or connector block including marking of MES number including taking down old unserviceable fan complete all as specified.

Supply, installation and testing desert cooler electric driven single phase having normal air flow capacity 4000 Cum per Hour made out of GI plain sheet of 20 SWG and side panels of 22 SWG, front grill heavy duty having minimum weight 3.0 Kgs made out of GI sheet, wood wool pads (set of three) weight not less than 500 gms superior quality, including suitable motor, water pump, PVC pipe, PVC elbow, PVC distributor three way superior quality for desert complete all as specified and directed.

9 Watt LED bulb in repair complete all as specified and directed.

Surface and wall mounted LED tube light fittings of capacity 18 watt, basic all purpose decorative ultra slim square profile LED fighting fixture with extruded polycarbonate environmental friendly, energy efficient ready in repair complete all as specified and directed.

M/s Shree Construction Company