PROVN OF IRON REMOVAL PLANT AT PUMP HOUSE NO. 06, 10 AND 15 AND UG SUMPS FOR PUMP HOUSE NO. 19, 16 AND B PARK AREA AT PANAGARH

Amount

B/R PORTION

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft/loose soil, complete all as specified and as directed by Engr-in-Charge.

Surface dressing n exc 15 cm deep and getting out in soft/loose soil, complete all as specified and as directed by Engr-in-Charge.

Excavation in trenches in soft/loose soil n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out, complete all as specified and as directed by Engr-in-Charge.

Excavation in trenches in soft/loose soil n exc 1.5 m wide and exc 1.5 m but n.exc 3.0 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out, complete all as specified and as directed by Engr-in-Charge.

Removing surplus excavated soil/earth to a distance not exc 50 M and deposited where directed at a level not exc.1.5 M above the starting point, complete all as specified and as directed by Engr-in-Charge.

Returning filling in soft /loose excavated soil including spreading leveling watering and well ramming in layers not exceeding 25 CM and all as specified and as directed.

M&L for sand filling in floors or pavings, laid in layers n exc 15 cm thick, spread, levelled and blinded with earth and rammed incl watering complete all as specified and directed.

Supply only unslaked (fat or magnesium) lime.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc 15 cm thick, spread, levelled and blinded with earth and rammed incl watering, complete all as specified and as directed.

M&L for hardcore of broken stone or boulder of gauge exc 63mm but n.exc 75 mm deposited, spread & leveled in layers n.exc 15 cm thick watered & rammed to a true surface, complete all as specified and as directed.

M & L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) as foundation and mass filling, complete all as specified and as directed.

M&L for M-25 Design mix using 20mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and as directed.

M&L for M-25 Design mix using 20mm graded stone aggregate Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed.

M&L for M-25 Design mix using 20mm graded stone aggregate as in chajjas, complete all as specified and as directed.

M&L for M-25 Design mix using 20mm graded stone aggregate Beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and as directed.

M&L for M-25 Design mix using 20mm graded stone aggregate Columns, pillars, piers, posts and struts, complete all as specified and as directed.

M&L for M-25 Design mix using 20mm graded stone aggregate as in fins/fascia, complete all as specified and as directed.

M&L for brick work with flyash bricks old size straight or curved on plan to any radius exc 6m mean radius build in CM 1:6, complete all as specified and as directed.

M&L for brick work with fly ash bricks old size straight or curved on plan to any radius exc 6m mean radius build in CM 1:4, complete all as specified and as directed.

M&L for 25mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in Damp proof course to horizontal or vertical surfaces including necessary formwork, complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surface of concrete, complete all as specified and as directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surface of concrete, complete all as specified and as directed.

Formwork to chullah hoods, chajjas, troughs and similar items including ege for rough finished surface of concreted, complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunch?ings, girders, bressummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc. also splays between floors and beams, etc for rough finished surface of concrete, complete all as specified and as directed.

Formwork to fins, louvers, fascia for rough finished surfaces of concrete, complete all as specified and as directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surface of concrete, complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel moulded both side Prelam PVC sheet strip of 20mm width stuck inside with solvent cement for stiles prelam PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of both side Prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing, complete all as specified and as directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm single side prelam PVC sheet & edges will be painted to match with prelam sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing, complete all as specified and as directed.

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and as directed.

S&F 150mm long Extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and as directed.

S&F 150mm long extruded Aluminium anodized barrel tower bolt of extruded section and fixed, complete all as specified and as directed.

S&F Aluminium alloy, 250mm long anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed.

S&F aluminium anodised tubular towel rail 20mm dia "D" type 60 cm long between flange fixed in repair, complete all as specified and as directed.

S&F Aluminum hat coat hooks , solid body, 175mm to 250mm all as specified and as directed.

S&F Wire netting of stainless steel wire 0.36mm dia fixed with tinned tacks of stainless steel wire staples, complete all as specified and as directed.

M&L for TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

M&L for TMT steel bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

M&L for TMT steel bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

S&F Steel rolling shutters, lath thickness 1.25 mm with out ball bearing, as specified including top cover, an?choring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type,complete all as specified and as directed.

Safety lever locks mild steel with 4 levers for rolling shutters, complete all as specified and as directed.

Ball bearing for rolling shutters, complete all as specified and as directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and as directed.

S&F Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch sp, complete all as specified and as directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded aggregate to receive tiles, complete all as specified and as directed.

M&L for joint free non skid coloured ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.06 Sqm but not exc 0.11 sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match the shade using coloured tiles incl 15mm thick screed bed in cement mortar 1:6, complete all as specified and as directed.

M&L for joint free Glazed ceramic coloured tiles in vertical surfaces (450 x 350mm) 7mm/ 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement or match, with backing coat 10mm thick in CM 1:3, complete all as specified and as directed.

M&L for 75 mm thick, Cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base, complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over screed bed or bedding layer 15mm thick in cement mortar 1:6, complete all as specified and as directed.

All as per Item No. 1.48 here-in-before but in skirting with backing coat 10mm thick in CM 1:3.

M&L for 75mm thick PCC 1:3:6 type C1 using 20mm stone aggregate as in plinth protection finished even and smooth with out using extra cement, complete all as specified and as directed.

M&L for 15mm thick in CM 1:4 rendering on brick or concrete surfaces finished even and smooth with integral water proofing compound on wall, complete all as specified and as directed. Note : WPC Measured and paid seperately.

Supply only intergral water proofing compound, complete all as specified and as directed. (liquid admixture)

M&L for 10mm thick in cement plaster CM 1:6 on brick or concrete surfaces finished even and smooth without using extra cement on wall, complete all as specified and as directed.

M&L for rendering 5 mm thick in CM 1:3 on ceiling finished even and smooth without using extra cement etc., complete all as specified and as directed.

M&L for 10mm thick in cement plaster CM 1:4 on brick or concrete surfaces finished even and fair with using water proofing compound, complete all as specified and as directed.

M&L for preparation new surface of roof and applying two coat of polyurethene (PU) acrylic based water proofing liquid compound over & including one coat of self priming primer @one litre per ten sqm with reinforcing fabric sheet as per manufactures instruction to stop leakage /seepage from roof/wall, complete all as specified and directed by the Engineer-in-Charge. Notes : 1. As per description of the items minimum two coats of polyurethene (PU) acrylic based water proofing liquid compound over one coat of primer shall be carried out by the as per manufacture instruction. Pl note no price adjustment shall be made, if more coats of (PU) acrylic based water proofing liquid compound & primer are required for roof treatment. 2. Quoted rate shall be deemed to be included for work in building/structure of any height.

M&L for three coats of white wash as in ceilings on newly plastered surfaces including preperation, complete all as specified and as directed.

M&L for three coats of white wash as on walls on newly plastered surfaces including preperation, complete all as specified and as directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including Preparation of new plastered surfaces, complete all as specified and as directed.

S&F Sheet glass, 4.0 mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane, complete all as specified and as directed.

S&F Sheet glass, 3.0mm thick pin headed quality and glazing with oil putty in square n exc 0.5 sqm in each pane, complete all as specified and as directed.

M&L for Preparation of new surfaces of steel and applying two coat synthetic enamel paint over a coat of redoxide primer to steel surfaces of any description not otherwise described over 10cm width or girth, complete all as specified and as directed.

S&F 15mm dia Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed.

S&F 20mm dia Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed.

S&F 25mm dia Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed.

S&F 15mm CP angular stop cock with flange, complete all as specified and as directed.

S&F 15 dia fancy type chromium plated bib taps cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe, complete all as specified and as directed.

S&F pillar taps, cast copper alloy, fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe and fixed, complete all as specified and as directed.

S&F Vitreous china Squatting pan Orissa pattern of size 580m x 440mm white with integral foot rests (excluding flushing cistern and flush pipe) complete including concrete bedding, complete all as specified and as directed.

S&F PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe, complete all as specified and as directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and as directed.

S&F vitreous china wash basin, white, flat back size 550x400mm, incl cutting for and pinning in ends of brackets or erecting stand but excl taps, pvc conections but incl brackets, waste pipe, waste coupling, complete all as specified and as directed.

S&F 500 litre capacity rotational moulded polythylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as per specified in SSR Part-I.

S&F PVC ball valves high pressure with polythene float and fly nut complete, screwed for iron pipe of 20mm bore, complete all as specified and as directed.

S&F brass chromium plated shower rose 125 mm size fixed in repair, complete all as specified and as directed.

S&F PVC grating doom 100 mm dia, complete all as specified and as directed.

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement of dia of out let 75mm, complete all as specified and as directed.

S&F PVC (SWR) pipes of 75mm dia double socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and as directed.

S&F PVC (SWR) pipes of 110 mm dia double socketed, in any length with rubber ring joints laid in floors, complete all as specified and as directed.

S&F PVC (SWR) door bends any radius for 75 mm bore dia, complete all as specified and as directed.

S&F PVC (SWR) bends any radius for 110 mm bore dia, complete all as specified and as directed.

M&L for 50mm thick PCC 1:2:4 type B1 using 20mm stone aggregate as in Ramp finished even and smooth with out using extra cement and making impression with XPM, complete all as specified and as directed.

Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and as directed.

E/M PORTION

M&L point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLS PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and as directed. Note : Quoted rate deemed to be included for necessary chasing/cutting and making good the surface.

All as per Item No. 2.01 here-in-before but One 3 pin 5 Amps socket out let points on independent board, complete all as specified and as directed.

All as per Item No. 2.01 here-in-before but 5 Amp socket on same board with other switches, complete all as specified and as directed.

Material and labour wiring for 15 Amps socket out let on independent Boards controlled by one, one way switch using 4.0 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLS cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and as directed. Note : Quoted rate deemed to be included for necessary chasing/cutting and making good the surface.

S&F switch piano flush type, single pole , 6 Amps, one way complete all as specified and as directed.

S&F switch socket combination 2 in 1 multipurpose 5 pin , (6 Amps ) flush type controlled by one switch complete all as specified and as directed.

S&F socket outlets 2 in 1, 5/6 Amps flush type230/240 V complete all as specified and as directed. (For Same Board only)

S&F switch socket combination 2 in 1 , 6 pin , (16 Amps ) flush type controlled by one switch complete all as specified and as directed.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps, complete all as specified and as directed.

S&F lamp holder, PVC/polycarbonate type with back plate straight or angular suitable for batten fittings, complete all as specified and as directed.

S&F stepped type electronic fan regulator flush type 240 Volts ISI marked, complete all as specified and as directed.

S&F 18 W LED light fitting wall mounted batten 4'ft , minimumm lumen output 100 lumen/Wat, extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 18 watt, 6000K including necessary connection, complete all as specified and as directed.

Supply and fixing 25 watt LED Bldg light fittings complete all as described here-in-below:- (i) Total system lumen not less than 2750 lumens. (ii) High pressure die cast aluminium. (iii) IP rating :- IP 66 (iv) Front cover : Toughened Clear glass. (v) Mounting :- Suitable for bracket arm 25 mm dia 1.0 m long (vi) Finish :- Epoxy powder coated with any additional treatment for smooth and anti corrisive finish. (vii) Lamp :- High bright LED with Lens. (viii) System efficacy (lm/W) of the luminaries :- Not less than 110 lm/watt. (ix) Colour temperature :- Not less than 5700K (x) Colour rendering Index (CRI) Not less than 74 (xi) Life : Not less than 50000 Hrs of opreation (xii) Optices :- Spread (Beam angle along the driveway)- 120degree, Through( Beam angle across the drive wat)- 60 degree, Beam pattern - Asymmetical driveway (xiii) Control gear:- Inbuilt electronic driver, PF not less than 0.90 and TDH less than 20% with operating voltage 140-270V AC, 50 Hz. (xiv) Surge protection :- Inbuilt surge protection minimum 5 KV (xv) Heat Sink :- As per OEMs design.

S&F epoxy powder coated sheet metal enclosure for DBs, double door, Single pole and neutral 230 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact, complete all as specified and as directed.

S&F MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection, complete all as specified and as directed.

S&F MCB SPN 6 to 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection, complete all as specified and as directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth wire electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth wire encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I, complete all as specified and as directed and testing on completion.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC), complete all as specified and as directed.

S&F metallic Exhaust ventilation fan of sweep 300 mm sweep, 230volt AC complete with louver and all asssesories including cutting hole of suitable size, making good surface by doing plaster and applying two coat of distemper complete with fixing connected with rwin core twisted flexible copper conductor (23/0.0076) of size, complete all as specified and as directed by Engr-in-Charge.

S&F LED Bulb 15 watt, ISI marked, suitable for batten holder, complete all as specified and as directed.

Supply, fixing, connecting, testing and commissioning of 6 Sqmm 2 core LT under ground cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cable (heavy duty) with multistranded aluminium conductor,1100 Volts grade in trenches/on wall/poles laid in ducts/inside protection pipe of the following cross sectional area including cable glands,lugs and suitable size of MS saddle clips (where ever cable laid in ceilings / walls without cable duct) all as directed by the Engr-in-Charge.

UNIVERSAL TRADING

MS ROYAL CONSTRUCTION INDEX NO 158 2010 BKP

SARASWATI ENTERPRISE (INDEX NO CEEC D-81)

M/S JK TRADING