CONSTRUCTION OF A- BLOCK, B-BLOCK,YATHIRI NIVAS, COMMERCIAL SHOPS, WORKS COMES UNDER MASTER PLAN III

Amount

Earthwork excavation for all works like column pits, trenches, manholes, inspection chambers etc, in all soils and subsoils including boulder studded soil to the required depth as may be directed except those soil which require chiseling, but including, shoring,strutting and bailing out water with special pumping wherever necessary and refilling the sides of foundation with excavated earth suitable for filling in layers of 150 mm thickness up to the natural ground level, watered, rammed and consolidated and depositing the surplus earth in

Boring, Providing and installing bored cast in situ single bulb under reamed reinforced cement concrete Pile of 450 mm dia and length top of pile cap in cement concrete M-25 {1:1:2 ( one cement one Coarse M.Sand and two Broken stone aggrigate)} using 20mm size

Supplying and filling in foundation, basement, etc with M- sand in layers of not more than 15 cm thick well watered,

Plain cement concrete 1:5:10 mix (one part of cement, five parts of sand and ten parts of 40 mm hard blue granite metal by volume) for leveling course in foundation trenches, manholes, inspection chambers etc., including charges for

Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat

Supplying and FILLING GRAVEL Supplying and filling in 'foundation and basement with filling crushed stone sand in layers

Providing pre - construction Anti-termite treatment by treating bottom surface and sides of excavation, back fill in immediate contact with foundation, top surface of plinth filling (at the rate of 5 litre of an emulsion concentrate of 1% of chloropyriphos 20 EC chemical per sqm of surface area) of approved brand, treatment to the soil along with external perimeter of the building by punching

Damp proof Course with Cement Mortar 1:4 (One cement & four sand) 12mm thick of the following mixed with water proofing compound of approved quality confirming to ISS @ 2% by weight

Supplying and erecting shuttering, necessary supports for plain surfaces such as reinforced cement concrete column footings, raft and raft beams, plinth beams, staircase steps etc.,

Supplying and erecting centering for sides and soffits including supports and strutting for plain surfaces such as reinforced cement concrete columns, pile caps, boxing slabs, fins and sunshades, facias, reinforced cement concrete walls, mullion

Supplying and erecting centering for sides and soffits including supports and strutting for plain surfaces such as reinforced cement concrete slabs, rectangular lintels, beams, T or L beams, reinforced cement concrete brackets, lintels, bed blocks,

Providing and laying in position, standardised concrete Mix M-25 Grade in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670

Foundation & Basement

Ground floor

First Floor

Second Floor

Third floor

Fourth floor

Fifth floor

Sixth floor

Providing & fabricating of reinforcement steel for reinforced cement concrete works in all heights and depths including straightening, cleaning, cutting, bending, placing in position and binding, hoisting and welding if any including cost of power,

Brick work in following Cement Mortar 1:5 using fly ash bricks of size 230 x 110 x 75 mm for foundation and basement

Foundation & Basement

Brick work in following Cement Mortar 1:6 using fly ash bricks of size 230 x 110 x 75 mm for foundation and basement

Ground floor

First Floor

Second Floor

Third floor

Fourth floor

Fifth floor

sixth floor

Brick partition walls of 11.50cm thickness in Cement Mortar 1:3 using Fly ash Bricks 230 x 110 x 70mm including cost and

Ground floor

First Floor

Second Floor

Third floor

Fourth floor

Fifth floor

Ceiling plastering with cement mortar 1:3 (One part of cement, three parts of sand by volume) for 12 mm thickness (average), for all internal/external slabs (flat/slopped/hipped/canopy), sunshades,

Wall plastering for brick work and concrete surfaces using cement mortar 1:5 (One part of cement, five parts of sand by volume) thickness 15 mm (average) for all internal/external

Flooring with following Double Charged Vitrified Tiles 600 x 600 x 10mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter

Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with

Cuddapah slabs of the following thick ness over a Brick partion walls for cubboard and pointed with cement mortar 1:3 ( one cement

Supplying and Paving the Paver Block flooring using Rubber mould paver block ( Colour ) of standard size over the M-sand filling of 63mm thick, including laying Compacting with power machine

Supply & fixing of single leaf solid core flush shutters with teak ply on both side with teak wood lipping all round 35mm thick, with necessary adhesives and CP screws complying witj standard

Supplying and fixing of FRP Door Sutter with FRP Door Frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost

UPVC Window Specification: Supplying and fixing UPVC (Un- Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be

UPVC Ventilator Specification: Supplying and fixing UPVC (Un- Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour)

Supplying and fixing of Metal and iron works for Windows And Ventilaters etc., in position. Rate inclusive of cost and conveyance

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for queue using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including

110 mm diameter.

Weathering course on top of roof slab with broken brick jelly of 20 mm gauge mixed with pure slaked lime, the proportion of brick jelly to lime being 32:12.50 by volume, well compacted by

Second Floor

Fourth Floor

Fifth Floor

Finishing the top of roof with one course of machine pressed tiles 20cmx 20cmx20mm of approved quality laid in cm 1:3,12mm thick

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard

Stucco plastering 12mm thick using blue granite chips of size 10mm and below over the existing base plastering with cement mortar 1:5,

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc - Manually Operated (up to 8 sqm. Area)

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and

Supply and fixing PVC water tank etc complete with standard specifications

Supplying and fixing of SS Sink of size 1200 x 550 x 180mm

Supplying and fixing of Brass Chromium Plated Screw Down/swan neck Tap 15 / 12mm dia of approved make conforming to I.S.specifications and quality including cost of shellac , thread

CP Wall Mixture Tap 3 in 1 system with Hand Showers

Pillar Tap

Swan Neck Tap

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) finolex or equivalent make (with ISI monogram) of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC

32mm UPVC pipe

15mm UPVC pipe

40mm UPVC pipe

Supply & Fixing in position of the following UPVC Specials Finolex or equivalent make (working pressure 10kg/sqcm

32mm UPVC Coupling

32mm UPVC elbow

32mm UPVC tee

32mm UPVC bend

15mm UPVC coupling

15mm UPVC elbow

15mm UPVC tee

40mm UPVC coupling

40mm UPVC elbow

40mm UPVC tee

20x15 UPVC reducer

20x15 UPVC reducer tee

32x25 UPVC reducer tee

40x32 UPVC reducer tee

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good

110mm dia. PVC

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to

110mm PVC Bend

110mm PVC elbow

110mm PVC tee

110mm PVC Door elbow

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using

Supplying and fixing in position of Indian make Water closet Oriyya Type of size 580mm x 440mm of approved uality with 'P' or 'S' trap

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 500 x 450 x 5.5mm thick mirror, shelf type with hard board backing of

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete

40mm valve

32mm dia.

15mm valve

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with

Wiring with 3 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin

Supply and fixing of 4’ 20W single LED Batten with LED complete on wall or ceiling with with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 7W / 9W LED bulb (SD 79)

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600mm down rod on the

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall (SD

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan (SD 120)

Supply and fixing of AC / DC 76mm buzzer / call bell suitable for 230 volts 50 c/s single phase AC supply on suitable TW board with

Supply and fixing of 1 no.6A two module 5 pin socket, 1 no. 6A one module switch with module cover plate (plastic) on suitable

Supply and fixing of 2nos.6A two module 5 pin socket, 2 nos. 6A one module switch with module cover plate (plastic) on suitable

Supply and fixing of 1 no. 6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable

Supply and fixing of 25A Flush type Wall Socket 25A DP MCB complete set for AC Plug in flush with wall with earth

Supply and fixing of 1500W automatic electric water heater of 35 litres capacity suitable for 230V 50 c/s AC supply on suitable MS clamps with 3 core flex wire but

Supply and fixing of DP sheet enclosure with 40A30 mA DP RCCB in flush with wall with earth connection

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire

Supply and Run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous

Supply and Run of 4 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous

Supply, Erection, testing and commissioning of 63A capacity dust and vermin proof horizontal type Metering cubical panel made up of 16 SWG CRCA Sheet with supply and fixing of the following 4Pole and 4pole ELCB / RCCB with busbar chamber, cable chambers and provisions for fixing TNEB Meters. For BLOCK A 1. 63A 4 P ELCB / RCCB -9 No. 2. Meter view glass - 9 Nos 3. 63A Fuse units - 27 Nos.

The busbar chamber shall consist of 4 Nos 25mm x 3mm copper flat for three phases and neutral. The 4 sqmm copper wire for interconnection between buses to 17 No 3 phase meter and FP ELCBs respectively. The copper flat buses shall be mounted on SMC busbar insulator at proper and sufficient interval as per IE rules. The busbar chamber shall be segregated from the adjacent chamber. The heat shrinkable sleeves shall be provided for busbar with colour code. The 25mm x 3mm copper flat for earth bus shall be provided all round the panel and 4 sqmm copper wire for Double earth connection for all outgoing

Supply and Laying of 3 1/2 x 70 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a

Supply and clamping of 3½ x 70 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and clamping of 3½ x 70 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and frxing of brass cable gland for 3-1/2 x 70 sq.mm. PVC armoured LTUG cable with earth connection (SD

Supply and providing cable end termination of 3-1/2 x 70 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32

Design, Manufacture, supply, erection, testing and commissioning of Passenger Lift with M/C room, Speed 1.5 m/s with Stainless Steel Panels, Disable friendly, microprocessor based controller, VVVF drive, Fire rated doors and ARD. with the following specifications: 10 Persons capacity (680 Kgs) Location of Lifts : Inside the building (Stilt + G +3 floors) (Data H) Location of Lifts : Inside the building i) Speed : 1.0 MPS ii) Floors : 1 floors (GF+FF) iii) Travel : 8.00 Mtrs (approx.) iv) Stops & opening 2 stops & 2 openings v) Controller: A.C. variable voltage & variable frequency vi) Automatic rescue device complete with dry maintenance free batteries as required. vii) Operation: Microprocessor based single automatic push

xi) Type of signal system a) Digital floor position indicator

xii) inside the car (lift should not start on overload)

d) Battery operated alarm bell and emergency light.

e) Car operating panel with fade proof luminous

xiii) Buttons in car and with intercom.

f) Luminous hall buttons at all landings.

g) Fireman’s switch at ground floor

xiv) Landing entrance

a) Location of landing entrance in central opening sliding

b) Number 1 No. at each floor

c) Size To suit the size of car door

d) Type of doors Horizontal sliding – centre opening-

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with

Supply and Run of 1 of No.8 SWG copper wire in suitable

Supply and fixing of 3 nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (Set plug) (SD 389)

Supply and laying of 2 x 10 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (SD 194)

Supply and clamping of 2 x 10 sq.mm PVC LTUG armoured Alu cable in on post or on wall with MS Clamps. (SD 180)

Supply of Duraline HDPE 90mm / 76mm DWC duct as per IS 16205 Part 2 for wherever necessary. (M- 1642)

Supply, Erection, testing and commissioning of 63A capacity dust and vermin proof horizontal type Metering cubical panel made up of 16 SWG CRCA Sheet with supply and fixing of the following 4Pole and 4pole ELCB / RCCB with busbar chamber, cable chambers and provisions for fixing TNEB Meters. For Block B1 & Block B2 1. 63A 4 P ELCB / RCCB -11 Nos. 2. Meter view glass - 11 Nos 3. 63A Fuse units - 33 Nos. 4. 63A neutral Link - 11 nos

The busbar chamber shall consist of 4 Nos 25mm x 3mm copper flat for three phases and neutral. The 4 sqmm copper wire for interconnection between buses to 17 No 3 phase meter and FP ELCBs respectively. The copper flat buses shall be mounted on SMC busbar insulator at proper and sufficient interval as per IE rules. The busbar chamber shall be segregated from the adjacent chamber. The heat shrinkable sleeves shall be provided for busbar with colour code. The 25mm x 3mm copper flat for earth bus shall be provided all round the panel and 4 sqmm copper wire for Double earth connection for all outgoing meters. The panel shall have powder coated painting of approved colours. The danger board shall be fixed at front of panel board. The panel shall be mounted on MS base channel provided all round at the bottom of the panel. The whole arrangements shall be erected on a masonary pedestal to be constructed with suitable foundation. The lowest metering chamber shall be a height of 0.75m from the ground level. (note: ELCBs / RCCBs shall be of L&T / Siemens / Legrand / Eql make). (Data G2)

Supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal wit suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour (SD 456)

Supply and fixing of single phase timer control for street light with 1 no. 32A DP MCB, 230V operated L&T 32A - 4 Pole Contactor (MCX-3) in suitable enclosure box with necessary accessories, painting and with required inter connections complete. (Data H)

xi) Type of signal system a) Digital floor position indicator in the car and at each floor

xii) inside the car (lift should not start on overload)

d) Battery operated alarm bell and emergency light.

e) Car operating panel with fade proof luminous

xiii) Buttons in car and with intercom.

f) Luminous hall buttons at all landings.

g) Fireman’s switch at ground floor

xiv) Landing entrance

a) Location of landing entrance in central opening sliding door-stainless steel

b) Number 1 No. at each floor

c) Size To suit the size of car door

d) Type of doors Horizontal sliding – centre opening- Automatic

Supply and fixing of 4’ 36W single LED Battern with LED complete on wall or ceiling with with round block PVC unsheathed Copper leads from terminals to the fitting. (Data J)

supply and fixing of 24W LED 2x2 square type fitting with LED (Higher end) on ceiling with suitable support on ceiling with PVC unsheathed copper leads from terminals to the fitting. (SD 439)

Supply and fixing of 1 no. RJ-11 (Telephone) socket with 1 module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (Data K)

Supply and fixing of 11W LED square type Surface fitting with LED (Higher end) on Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. (Data L)

supply and fixing of 18W LED square type fitting with LED (Higher end) on Ceiling with suitable support on ceiling with PVC unsheathed copper leads from terminals to the fitting. (SD 441)

Supply and fixing of 2' 6W LED battern type fitting with LED (Higher end) on wall with necessary accessories with PVC unsheathed copper leads from terminals to the fitting. (Data G)

Supply and fixing of 3M LED foot lamp with LED (Higher end) suitable to be fixed on 3M flush type (GI) box inflush with wall with necessary accessories with PVC unsheathed copper leads from terminals to the fitting. (Data N)

Supply and fixing of 10W façade light with IP 65 dust proof and water resistant on wall with necessary accessories and electriccal connections complete.(Data I)

Supply and fixing of decorative wall fitting with fancy glass shade with 7W LED bulh on wall with necessary accessories and electriccal connections complete. (Data P)

Supply and fixing of 1400mm (56") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600mm down rod on the existing fan clamp (SD 504)

Supply and fixing of 1 no. 20A 2M Key fab on suitable module concealed Box (GI) in flush with wall with connections. Higher End (Data Q)

Supply and fixing of 1.5 TR Split AC with 4 KVA stabilizer with copper coils 5 star rated of reputed make with required accessories and as directed by the departmental officers. (Data R)

Supply and Run of CAT 6 in suitable PVC rigid pipe Concealed in wall and ceiling with continuous and making good of the concealed portion (For CCTV and Telephone) (Data S)

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (SD 573)

Supply and fixing of 6 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100A 4P MCB as incoming and 18 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (Data T)

xi) Type of signal system a) Digital floor position indicator in the car and at each floor

xii) inside the car (lift should not start on overload)

d) Battery operated alarm bell and emergency light.

e) Car operating panel with fade proof luminous

xiii) Buttons in car and with intercom.

f) Luminous hall buttons at all landings.

g) Fireman’s switch at ground floor

xiv) Landing entrance

a) Location of landing entrance in central opening sliding door- stainless steel

b) Number 1 No. at each floor (Total 2 floors)

c) Size To suit the size of car door

d) Type of doors Horizontal sliding – centre opening- Automatic

Supply and laying of 2 x 10 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (SD 176)

Supply and Laying of 3½ x 120 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (SD 664)

Supply and clamping of 3½ x 120 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (SD 205)

Supply and fixing of brass cable gland for 3½ x 120 sqmm PVC armoured LTUG cable with earth connection. (SD 169)

Supply and providing cable end termination of 3½ x 120 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 218)

Supply and Laying of 3½ x 25 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (SD 659)

Supply and clamping of 3½ x 25 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (SD 182)

Supply and fixing of brass cable gland for 3½ x 25 sqmm PVC armoured LTUG cable with earth connection. (SD 164)

Supply and providing cable end termination of 3½ x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 213)

Supply and fixing of single phase timer control for street light with 1 no. 32A DP MCB, 230V operated L&T 32A - 4 Pole Contactor (MCX-3) in suitable enclosure box with necessary accessories, painting and with required inter connections complete. (Data U)

Supply, Erection, testing and commissioning of 250 A capacity dust and vermin proof horizontal type cubical panel board made up of 16 SWG CRCA Sheet with supply and fixing of the following interior switches with HRC fuse links arranged horizontally with horizontal busbar chamber and cable chambers. 1. 250A TPN switch disconnector fuse unit interior only with HRC fuses double break-1 No. 2. 32A TPN switch disconnector fuse unit interior only with HRC fuses double break-2 Nos. 3. 63A TPN switch disconnector fuse unit interior only with HRC fuses double break - 4 Nos. 4. 100A TPN switch disconnector fuse unit interior only with HRC fuses double break - 4 Nos.

The busbar chamber shall consist of 4 Nos 33mm x 6mm copper flat for phases and neutral and interconnection between incoming switch and buses. The 38mm x 6mm copper flat for interconnection between TPN switches and buses. 38mm x 6mm copper flat buses shall be mounted on SMC busbar insulator at proper and sufficient interval as per IE rules. The busbar chamber shall be segregated from the adjacent chamber. The heat shrinkable sleeves shall be provided for busbar with colour code. The 25mm x 3mm copper flat for double earth connection for all incoming and outgoing switches are to be provided in this panel. The panel shall have powder coated painting of approved colours, approved by the department officers. The danger board shall be fixed at front of panel board.

The panel shall be mounted on MS base channel provided all round at the bottom of the panel. The whole arrangements shall be erected on a Masonary pedestal to be constructed with suitable foundation with bolts and nuts such that the lowest SDF unit fuse handle is at a height of 0.75m from the ground level. (Note: All SDF unit shall be of L&T / Siemens make). (Data V)

Supply and Fixing of 250A 3 Phase LTCT size (3' x 4' x 1') 3 tier Panel comprising 300A, 500V Fuse Units and Neutral Link, Test block with required accessories and 250/5A CT coils for Meter Reading in a separate compartment with bus bar arrangement with 33mm x 6mm copper bus bar R,Y,B,N connection and Earth bus copper 25mm x 3mm for Earth connection on suitable angle iron frame work, erection charges with suitable foundation bolts and nuts, washers and grouting with cement concrete, testing and commissioning with complete wiring from CT meter to energy meter. (Data X)

Supply, erection, commissioning and testing of 125 KVA Diesel generator set with acoustic arrangements in accordance with CPCB norms, water / coolant oil cooled type engine with not less than 158 BHP for 125 KVA generator at 1500 rpm under NTP conditions with following specifications

The engine should have turbo charged, should be provided with air cleaner, base frame, crank case, lubricating oil, fan and fan drive, fuel and oil filters, flexible fittings, exhaust governor, hydro mechanical gauges for fuel pressure and oil pressure, tachometer, digital water temperature gauge, charging arms, muffler, exhaust pump for fuel priming, fuel transfer, jacket with radiator engine oil, safety set ups with engine shutdown system for LLOP including the set of tools, spares as supplied by the manufacturer along with the Engine. The alternator should have brushless self- excited we connected, self-regulated of continuous rating, developing an output 100 KW capacity at 0.8 power factor lagging, 415 V, 3 phase, 50 Hz at 1500 rpm with a voltage regulation of ±1 % under steady state condition with over speed capacity of 10% for 5 minutes withstanding capacity with class H insulation, ingression protection of IP23 with topicalization. The alternator is to be designed, built & tested to IS, BS, IEC or any other equivalent Indian or International Standards.

Supply and providing electrical safety & firefighting accessories complete as detailed below. (Data U)

2m x 1m Rubber Mat (5 sets) suitable for 11 KV installation confirming to IS - 2 Nos.

First Aid Box complete with all First Aid Medicines - 2 Nos.

Shock Treatment Chart fixed in glass frame - 2 Nos.

Fire Buckets - 4 nos. with MS Angle frame stand - 2 Nos.

4.5Kg CO2fire extinguisher confirming to TAC norms - 6 Nos.

Metallic Danger Board as required by the Electrical Authorities - 2 Nos.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection (SD 76)

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD 211)

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection (SD 371)

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (SD 514)

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (SD 660)

Supply and Laying of 3½ x 50 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (SD 661)

Supply and clamping of 3½ x 50 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps. (SD 184)

Supply and fixing of brass cable gland for 3½ x 50 sqmm PVC armoured LTUG cable with earth connection. (SD 166)

Supply and providing cable end termination of 3½ x 50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD 215)

Supply, Erection, testing and commissioning of dust and vermin proof horizontal type Metering cubical panel made up of 16 SWG CRCA Sheet with supply and fixing of the following 4Pole and 2pole ELCB / RCCB with horizontal busbar chamber, cable chambers and provisions for fixing TNEB Meters. 1. 63A 4 P ELCB / RCCB -1 No. 2. 40A DP ELCB / RCCB - 15 Nos. 3. Meter view glass - 16 Nos

Supply, Erection, testing and commissioning of dust and vermin proof horizontal type Metering cubical panel made up of 16 SWG CRCA Sheet with supply and fixing of the following 4Pole and 2pole ELCB / RCCB with horizontal busbar chamber, cable chambers and provisions for fixing TNEB Meters. 1. 63A 4 P ELCB / RCCB -1 No. 2. 40A DP ELCB / RCCB - 15 Nos. 3. Meter view glass - 16 Nos

The busbar chamber shall consist of 4 Nos 25mm x 3mm copper flat for three phases and neutral. The 10sqmm copper wire for interconnection between buese to 1 No 3 phase meter and 10 nos single phase meters to 4P and DP ELCBs respectively. The copper flat buses shall be mounted on SMC busbar insulator at proper and sufficient interval as per IE rules. The busbar chamber shall be segregated from the adjacent chamber. The heat shrinkable sleeves shall be provided for busbar with colour code. The 25mm x 3mm copper flat for earth bus shall be provided all round the panel and 10 sqmm copper wire for Double earth connection for all outgoing meters. The panel shall have powder coated painting of approved colours. The danger board shall be fixed at front of panel board. The panel shall be mounted on MS base channel provided all round at the bottom of the panel. The whole arrangements shall be erected on a masonary pedestal to be constructed with suitable foundation. The lowest metering chamber shall be a height of 0.75m from the ground level. (note: ELCBs / RCCBs shall be of L&T / Siemens make). (Data C)

xi) Type of signal system a) Digital floor position indicator in the car and at each floor

xii) inside the car (lift should not start on overload)

d) Battery operated alarm bell and emergency light.

e) Car operating panel with fade proof luminous

xiii) Buttons in car and with intercom.

f) Luminous hall buttons at all landings.

g) Fireman’s switch at ground floor

xiv) Landing entrance

a) Location of landing entrance in central opening sliding door- stainless steel

b) Number 1 No. at each floor (Total 2 floors)

c) Size To suit the size of car door

d) Type of doors Horizontal sliding – centre opening- Automatic

GST 18 % in Figures

M/s. Kousic & Co (BID ID -1278539)

kadal constructions (BID ID -1275892)