Redevelopment of Adarsh Nagar, Faridabad with Defect liability period of two years and including maintenance for 5 years under Smart City Mission. Recall

Providing and fixing of reinforced Ferro-Cement drain covers designed for `A` class loading duly marked on cover with adequate steel reinforcement having thickness 75mm to 150mm anti corrosive bitumen painted M.S. plate , Rim and M.S. lifting hooks, Admixtures like plasticizer, bond improving compound, shrinkage, resistance compound, abrasion resistant complete as per approved design etc Standard Size 1500x600mm (125mm thick) for span 701 to 1200mm

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work : 25 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 50 mm dia. nominal bore

MAIN CUBICAL PANEL / STREET LIGHT CONTROL PANELP/F testing and commissioning of kiosk type weather proof out door main cubical panel size 750 mm X 1250 mm X 500 mm (app.) made out of 14 gauge MS sheet front and back both side openable duly hinged door with locking arrangement by providing both side held draft and all required hard wares. The cubical should be dust and vermin proof followed by coat of zimpholite primer and finally two coats of enamal gray paint. The cubical should be mounted with hard ware on angle iron frame size 50 X 50 X 6 mm and 1500 legs duly painted framed be grouted 750 mm below ground level with cement concrete 1:3:6 in 1000 X 500 X 600 mm and providing brick masonary along angle iron frame above G.L. They shall be in two section comprising as follows: (i) Providing and Fixing 415 V ,TP combination double break HRC switch fuse unit .100 Amp. rating for incoming supply with HRC fuse 100 Amp rating and of BCH/LandT/EE/ Siemens/ ABB make. (ii) Providing fixing timer switch TSQ 100 series 240 Volts, and full running service standred mounting with base of L and T or equivalent make including the cost of contactor 63 amp. 50 Hz. 440/400 volt. (iii) P/F open busbars 25mmX3mm of required length duly covered by heat shrinkable sleeves with busbar supporters (iv) Provision for residual current operated 63 Amp. 1 Pole ELCB of 30MA to 300 MA sensitively as required including making connections etc.(EE/Load stop make) (v) P/F 2 Nos. 415 Volts TPN combination double break switch fuse unit,63 Amp. Rating with HRC fuses (EE/mds/ SCHNEIDER bch/Siemens )for outgoing cable and making connection etc. also to have a provision for two nos. above switchs. (vi) P/F of 3 nos. RYB phase indicator resitance type complete with lamp P/F of HT danger plate of size 200 X 150 mm made of aluminium sheet 20 gauge. (vii) P/F cable glands double compression type and Al. lugs duly crimped for incoming cable and out going Cables. (viii) Providing 2 Nos. earth terminals including lugs and H/W duly inter connected with 8 SWG copper wire . (ix)Inter connection of main busbar to each out going switch and cable terminal shall be with 4 sqmm PVC copper conductor duly crimped with AL lugs. (x) Cable termination shall be fixed at backside of the panel with H/W and spring washers (xi) Light control switch with photo senser complete unit as required

P/ F IP-65/ IP-66 protected street light luminaries on existing bracket. Fixture made from powder coated single piece pressure die cast aluminum housing with heat dissipation fins on housing with high power LEDs . Diffuser / glass cover for ensuring IP-65 protection for lamp and control gear compartment, system lumen output of 100 lum/watt high power LED. Integrated driver shall be high efficiency having efficiency more than 85 % and in compliance to IEC standards. System life of 50000 burning hours with 70 % of initial lumens maintained. Fixture shall be in CE compliance. LED street light fixture 80-90 watt

Supply and erection of Octagonal pole of following length and dimension as per table-3 with base plate on the cement concrete foundation of M-15 /M-20 grade (1:1.5:3) with the help of anchor bolts of grade 6.8 (IS 1367 P III ). The pole shall be made of S-355JO grade steel sheet , folded lengthwise to obtained Octagonal shape, having single longitudinal seam weld and hot dipped galvanised internally and externally in accordance with IS 2629. The pole shall have a weatherproof flush door and locking arrangements. The complete work shall be supervised and certified by the manufacturers for satisfactory supply, erection, testing and commissioning. Single arm overhang

Supply and installation of maintenance free Earthing with all alied material

Supply and erection of 25 mm x 6 mm 9 mtr for earthing Wt. 10.80 Kg (Tata/ Sail make)

Erection of G.I. Wire GI Strip 25x6mm 9 mtr for earthing

Providing and fixing 6 SWG dia GI wire on surface or in recess for loop earthing as required