Renovation of Tea Tribe Rest House at Shillong

Amount

Civil Works

PLAIN CEMENT CONCRETE WORKS

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).

REINFORCED CEMENT CONCRETE WORKS

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately)

(A) In substructure up to plinth level

b) M20 grade concrete or Prop. 1:1.5:3

(B) In super structure from plinth level up to 1st floor level.

b) M20 grade concrete or Prop. 1:1.5:3

TIMBER SHUTTERING (FORMWORK)

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in:

(a) Using 38mm thick plank

Staircase with sloping or stepped soffits including risers and stringers but excluding Landing. (Using 38mm thick plank)

Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.

(b).Brick on edge soling

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.

(I) In Sub-structure upto plinth level including dewatering if necessary

(a) In proportion 1:3.

230mm thick brick wall in cement morter with 1st class brick including racking out joints and curing complete as directed in structure

(I) In Sub-structure upto plinth level including dewatering if necessary

(a). In proportion 1:3.

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately)

(A) 112mm thick brick wall

(a) In cement mortar in proportion 1:4. (1 cement:4 sand)

Providing SUN ROCK HIGH CTS/ DEVI paver block/tiles of concrete grade M30 or above of approved quality, size, shape of specified thickness over a leveling bedding layer of 30mm compacted sand over a base course of WBM or PCC (Base course to be paid separatly) including cutting where necessary finished with spreading , sweeping jointing sand and compacting the pavers using vibrating compactor as specified and directed.

SUN ROCK HIGH CTS/ Devi Tiles (Pavers)

(a) 80 mm thick

STONE MASONARY WORK

Stone masonary work in retaining wall, wing wall, abutment, foundation, steps, plinth etc. in cement mortar in prop 1:6 with levelling course of 1:6:12 with both faces hammer dressed including bonding, providing face stone, through stone and centering including racking of joints, curing and supplying and all carriage of stone as directed including payment of forest royalty and sales tax and carriage.

(a) Random Rubble Masonry

65 mm thick cement concrete floor consisting of 50 mm under layer of cement concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 25mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement :1 coarse sand : 2 coarse aggregate of size 10mm down) laid in panels and finished with a floating coat of neat cement finish (using cement slurry for bond @ 2.75 kg. per square metre of floor area) including curing etc. complete as directed.

20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed.

A) On rough side (backing coat 15 mm and finishing coat 5mm thick)

a) In cement mortar 1:3

B) On fair side (backing coat 10 mm and finishing coat 10mm thick)

a) In cement mortar 1:3

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level)

a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL

(i) TMT Corrosion resistant steel (CRS) reiforcement bar

Construction of Granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per Clause 401 of MoRTH specifications (with an initial lead of 5 km) (including cost of testing of materials at site and laboratory as directed by the deptt.)

(a)Using Grading I material

Providing and laying of inter locking concrete block pavement (ICBP) with cement concrete paver blocks as per IS 15658-2006 of thickness 80mm and 28 days compressive strength not less than 40 N/m over a layer of bedding sand of compacted thickness 30mm, laid either in stretcher/ running/ herringbone pattern of bonds as directed by the engineer and in proper level and grade and compacted with appropriate equipment such as plat vibrator along with spreading of a thin layer of joint filling sand to fill up the gaps between blocks including construction of edge restraint wherever required complete as per drawings and Technical specification clause 1504 of MORD.

Providing drain with brick work in cement mortar in proportion 1:5 with half brick thick side walls and 100mm thick C.C (1:3:6) base over one brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified.

ii). 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

Supplying and planting of house plants in required size of pot including filling the pot to the top surface with appropriate soil media of garden soil, river sand, cow-dung, leaf mould, fertilizer, pesticides as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed . (Mixing of different ingredients of soil media to be made in presence of Deptt. official / Specialist concerned)

(A) With Fancy leaf caladium/Coleus

(ii) Using earthen pot of 60 cm dia.

(B) With Indian rubber plant / Prayer plant

(iii) Using concrete pot of 60 cm dia.

Supplying and planting of palms with required size of pot including filling the pot to the top surface with appropriate soil media made of garden soil, river sand, cow-dung, leaf mould, fertilizer, pesticides as per specification...........................

(A) With Bottle palm

(II) Using earthen pot of 60 cm dia.

Supplying and planting of seasonal flower in required size of pot including filling the pot to the top surface with appropriate soil media made of garden soil, river sand, cow-dung, leaf mould, fertilizer, pesticides as per specification ..............................

(II) Using earthen pot of 60 cm dia.

Supplying and planting of Dahlia / Chrysanthemum / Gladiolus on the ground ( bed planting, bed size 45 cm x 45 cm x 45 cm) including the preparation of the soil, providing .......................... as specified and directed .

Supplying and planting of ornamental trees (1'-0" height sapling) including pit making ( 60 cm x 60 cm x 60 cm ), filling the pit with appropriate ......................... as specified and directed .

SHADE TREE

(A) Neem / Mahaneem / Beef wood / Bakul / Acacia / Siris / Devils tree / Kadam / Palash / Pink Cassia / peepal / Silver oak / Simalu / Ajar

Providing and fixing Stainless Steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i.e. fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in-charge. (For payment, only weight of Stainless Steel member is to be considered. No extra payment for fixing accessories such as nuts, bolts, fasteners etc. will be considered)

PWD Roads Schedule 2018-19

Excavation in ordinary Rock by

a)Excavation in ordinary Rock using manual means including loading in a truck

Electrical Works:

Dsupplying & laying of 25x4 mmsize copper strips…………………………………………..by the dept

Supply fitting and fixing of lighting final Arrestor……………………….by the dept.

Supply with installatipon and commissioning of ……………………………….chemical earthing ……………..by the dept

Supplying including fitting and fixing of the following Oil filled/ heat convertor/halogen heater completed as directed and specified by the deptt. (Bajaj or equivalent)

Halogen room heater RHX 3T

Supplying and installation and commissioning…………….panel board…………………electrical items

0-40 Amp electro-mechanical counter display 3 Phase 4 wire electronic hybrid energy meter

Supply with fitting & fixing 60 mm dia 3050 mm height single arm DECORATIVE tubular pole………………………….equivalent

Supplying and fitting fixing of electric storage water heater (Geyser)…………………as directed by the department.

10 ltrs Capacity

Supplying with fitting fixing ………………………..high power LED ………………..By the deptt.

Wiring for drawing sub main line with P.V.C insulated single core…………………….wiring system

With 2 x 2.5 sq.mm + earth continuity with 1 x 1.5 sq.cable in 20 mm dia rigid steel conduit

Supply and laying of the following sixe Solid Aluminium conductor

25.00 Sq mm 3&1/2 core U.G cable in 40 mm dia medium duty G.I pipe

90 mm to 45 mm size stone aggregate

Supplying with fitting and fixing panel mounting 25 KA 415V 50 Hz 4P MCCB ……………….by the deptt.

Supplying with fitting and fixing DP 10 KA 240/415 V 50 Hz MCB of the following capacity complete with making necessary connections as approaved, specified and directed by the deptt.

Supplying fitting and fixing 700 ltrs refridgerator (Samsung/ Whirpool) make

Supplying fitting and fixing 32 litre microoven (L.G/ panasonic make)