SPECIAL REPAIRS TO BLDG NO 124E AT HEMRL PUNE

Amount

Demolition of brick work / stone masonry / PCC block masonry built in cement mortar or cement lime mortar including all quoins, pillars, arches etc, but excluding ashlar facings dressed stone work and precast concrete articles complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in soft / disintegrated rock complete all as specified and directed.

Returning filling including spreading, leveling watering & Well ramming in layers n.exc 25 cm thick in soft/disintegrated rock complete all as specified and directed.

Removing excavated Soft/disintegrated rock exc 250m & not exc 500m and depositing where directed at a level n. exc 1.50m above starting point complete all as specified and directed.

M&L PCC (1:3:6) type C-2 using 40 mm graded stone agg as in fdn filling mass concrete complete all as specified and directed.

M & L Pre-cast cement concrete block masonry type C1 1:3:6 (20 mm graded aggregate)with solid blocks, exc. 10 cm in width and setting in mortar (1:6), complete all as specified and directed.

M & L Rendering 10mm thick on brick or concrete surfaces in CM 1:4 & finished even and smooth without using extra cement complete all as specified and directed.

M & L for Providing PCC (1:24) type B1 using 20 mm graded agg as in coping / Channel of drain etc complete all as specified and directed.

Material and labour for Complete removal of existing Roof treatment in any layers including demolition of PCC in roofs unreinforced and disposal of debris to distance exc 250 metre and not exc 500 metre out of MoD land complete all as specified. Note: i) The rates are inclusive of removal for any type old water proofing treatment over to Main RCC slab. Bidders is advised to visit the site and ensure before quoting rates. ii) All the dismantled debris are required to be removed from HEMRL premises right after demolition so that process of user should not get obstructed.

Material and labour for PCC 1:2:4 (Type B0 using 12.5 mm graded crushed stone aggregate) (40mm thick avg) as in levelling course to match the undulations of roof and in coving, roof kerbs including benching etc including necessary formwork and finished rough surface complete all as specified and directed.

Material and labour for PCC 1:2:4 type B1 (using 20 mm graded aggregate) as in benching, coping, kerbs and the likes including weathering slightly rounded or chamfered angles and throating as directed including necessary use and waste of form work complete all as specified and directed.

Material and labour for rendering of 10 mm thick in cement mortar 1:3 mixed with liquid water proofing compound (ISI marked) of approved make as per manufacturer's instructions over RCC roof slab and finished fair and even without using extra cement complete all as specified and directed. NOTE: Liquid water proofing compound shall be measured and paid seperately as 'Supply only'

Material and labour for mechanical cleaning of surface to make it free from any bituminous residue/ dirt, oil , Greece or similar material. There after crack treatment by cutting open cracks and cleaning based sealent including application of PU based primer complete all as specified and directed.

Material and labour for applying water based polyurethane modified dispersion (single component, cold applied, non toxic, VOC complaint) in 03 coats including 01 coat of epoxy primer @ 0.15 Kg per Sqm followed by two coats of polyurethane coating with 1.5 Kg per sqm in two coats etc complete per manufacturer specification complete all as specified and directed.

Notes For Item Nos 13 & 14 : 1. Properties of Polyurethane based chemical shall confirm to following Technical Parameters:- (i) Highly Elastic and shall have crack bridging ability of upto 3mm as per AS NZ 4548 (ii) UV Resistance. (iii) Adhesion to concrete and shall resist 7 bars of hydrostatic pressure. (iv) Tensile strength should not less than 2.0 N/sq.mm for free film & 60 % solid content as per ASTM C 1250 (v) Elongation should not less than 300% as per ASTM D2370 (vi) Solid content by weight should not less than 60%. (vii) Air/water permeability BSEN 12390 AT 5 bar -72 hours should be NIL and minimum dry film thickness of water proofing membrane must be 1.0mm. (viii) Accelerated weathering (ASTM453) should Pass 1000 hours. (ix) Reaction to fire - non inflammable. 2. The work shall be executed thru auth applicator of manufecturer only. Contarctor has to provide manufecturer test certificates for the above mentioned technical parameters and PVs. 3. The conractor has to submit the guarntee for 10 Years against the water proofing treatment. Make:- Bostic, Berger,Fosroc, sika, Asian.

Supply only integral liquid WPC of approved make.

Taking down rolling shutter any type including top covers of size of Shutter area upto 15 Sqm complete all as specified and directed.

Taking down steel collapsible gate of any type and Area of gate n.exc 10 Sqm complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S & F Mild Steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other coveringin Fe 410-W (Gde- E- 250) quality-A . Doors, etc. to be prepared for hanging or sliding with and including either hooks and pintle hinge or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; incl errection and fabrication also fastening and fixing complete all as specified and directed.

Supplied and fix Steel rolling shutters, Thickness of laths in 1mm with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, gear operated type with bevel gear box and crank handle complete all as specified and directed

S & F collapsible steel gates top hung consisting of channel pickets, pivoted flat bars top and bottom runners brass handles etc as specified erected in position and securing runners with holdfasts and brackets complete all as specified and directed.

Taking down rolling shutter any type including hood covers, top covers for carrying out repairs/ replacement of worn out parts such as brackets, guide, shaft, pulleys, gear wheels, gear boxes and straightning partition, side patti, press button, rails, tightening end clips, cleaning and greasing the parts in good condition and refixing for Shutter area upto 15 Sqm complete all as specified and directed.. Note: Spares replaced will be measured and paid separately as "Supply only".

Supply only the following items As per existing ( to be replaced against Ser Item No 23 here -in- before) complete all as specxified and directed

(a) Heavy duty spring n.exc 45 cm long.

(b) Gear box set.

(c) Safety lever lock MS.

(d) Top Cover (18 gauge).

(e) Mild steel flat 18 x 5mm.

S & F in repair projecting type hinges / steel handle/ and steel peg stay/ brackets including necessory fitting and fixtures for steel windows fixed with screw bolts or with welding complete all as specified and directed

S & F in repair any type hinges / steel handl for steel door fixed with screw bolts or with welding complete all as specified and directed by

Taking down cement plaster on brick or stone walls or concrete surfaces etc incld raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for Rendering 15mm thick in two layers on fair faces of brick work or concrete surfaces 10mm in CM 1:6 and top layer in CM 1:4 mixed with integral water proofing compound finished fair and even complete all as specified and directed. NOTE: WPC shall be measured and paid separately.

Material and labour for Rendering 15 mm thick in CM 1:6 on internal surfaces of brick wall finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5 mm thick plastering in CM 1:3 on ceiling and finished even and smooth without using extra cement complete all as specified and directed.

Material and Labour for preparation of newly plastered ceiling surface and applying three coats of white wash, complete all as specified and directed.

Material and labour for preparation of newly plastered wall surface and applying two coats oil bound distemper a coat of 3mm thcik wall interior wall care putty and a coat of primer complete all as specified and directed

Material and labour for preparation of newly plastered wall surface and applying two coats of acryalic weather proof exterior emulsion paint over a coat of 3mm thick exterior wall care putty and a exterior primer on wall complete all as specified and directed

M & L for preparation of old ceiling surfaces and applying two coats of white wash complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for Complete removal of exisiting treatment on wall / ceiling surfaces and preparation of old wall surfaces by filling holes etc and applying two coats of acryalic weather proof exterior emulsion paint over a coat of exterior primer on wall complete all as specified and directed.

M & L for complete removal of existing treatment (Paint / distamper) on walls and applying 3 mm thick wall care putty after that applying two coat of distemper oil emulsion over a coat of alkali resistance primer on wall complete all as specified and directed.

Material and labour for complete removal of existing treatment of Surfaces of any description wood, steel, iron, concrete, brick, stone, etc including preparation and applying of two coat of fire resistance paint over and including a coat of primer complete all as specified and directed.

Material and labour for preparation of new Surfaces of any description wood, steel, iron, concrete, brick, stone, etc. exceeding 10cm in width or girth and applying two coats of fire resistance paint over zinc primer complete all as specified and directed.

Taking down Chowkats or frames any type exceeding 1.5 Sqm and n. exc 4 sqm each (Without taking off shutters from the frame) complete all as specified and directed

Taking down Chowkats or frames not exceeding 1.5 Sq. M each (Without taking off shutters from the frame) complete all as specified and directed

Taking down shutters of any description exceeding 1 Sq. M but not exceeding 2 Sq. M each and refixing in the same opening. complete all as specified and directed.

M&L pressed steel frame for doors size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M & L providing cement concrete (1:3:6) type C1 using 20mm graded aggregate for filling in pressed steel frames and other similar items etc complete all as specified and directed.

Supply & Fix solid PVC door frame of size 50mmX47mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube all as specified and directed.

Supply & Fix Factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and directed..

Supply & Fix 125mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply & Fix 100mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

Supply & Fix 125mm long Extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

S&F 35mm thick factory made flush shutters, solid, core construction with block board core and plywood face panals commercial type on both sides complete all as specified and directed.

Supply & Fix 200mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

Supply & Fix 300mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled of drawn brass bolts and fixed complete all as specified and directed.

Supply & Fix 125mm long Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-12 complete all as specified and directed.

Supply & Fix 150mm long Extruded brass handles, fabricated type polished complete all as specified and directed.

Supply & Fix 150mm long Floor door stopper of brass body and tongue, with hard drawn steel spring. Fixed in floor complete all as specified and directed.

Supply & Fix Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of apperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

Material and labour fo preparation of new wooden surfaces of width or girth over 10 cm and applying two coats of synthetic enamel paint over and including a coat of pink primer complete all as specified and directed.

Material and labour fo preparation of new or previo-usly un painted steel surfaces of width or girth over 10 cm and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Taking down chowkhats / frame incl shutterrs or Steel windows / ventilators incl shutterrs (without taking off shutters from the frame) any type and size complete all as specified and directed.

M & L for Aluminium Powder coating section (minimum thickness of powder coating 50 micron) for door/window / Ventilators/partition etc frames & shutters sliding or openable type including necessary joining cleats, Hinges,tower bolts,handles,mullion glazing clips, rubber packing, anodised aluminium snap beading , screws, sliding track,roller etc of standard sections complete all as specified and directed.

S & F side hug Steel windows glazed shutter using rolled steel section including hinges, hold fast, flat latches for locking inclusive of required fittings and fixturees and provision of peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick sorrounds, glazed with oil putty or fixed with beads complete all as specified and directed.

Supplied and fix Rough cast wired glass n exc 0.5 sqm, 6.4mm thick and glazing with oil putty in square complete all as specified and directed.

Scraping loosened/cracked concrete of RCC structure at any location by chiselling etc including removal of debris away from n.exc 500 mtr site all as complete all as specified and directed.

M&L for pressure guniting 25mm thick lath over existing RCC structure with CM (1:3) incorporating with approved acryic polymer agent and 5mm thick plaster CM (1:4) for finished the gunited surfaces even and fair without using extra cement including scaffolding any height from base all as specified and as directed. Note : Acyrlic polymer shall be measured and paid seperately under relevant items of this sch.

Supply only Arcylic polymer agent of approved make of pressure guniting

Supply and fixing for hard down steel wire fabric not exceeding 4 kg/sqm cut to lengths, bent to shape mild steel wire, (annealed) not less than 0.9mm dia as in reinforcement complete all as specified and directed.

Dismantling existing tanks and removing to store of capacity exc 500 ltr n.exc 1000 ltrs complete all as specified and directed.

S & F rotational moulded polyethylene water storage tanks (cylindrical verticla with closed top) hoised and fixed in position all as specified in SSR Part I of capacity 1000 ltrs complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Providing & fixing of Armstrong Soft Fibre Acoustical Suspended Ceiling System with fine fisuured bev 600 x 600 x 16mm with suprafine 15mm grid with Armstrong 15mm exposed grid. The tiles should have Humidity Resistance (RH) of 95%, NRC 0.9 - 1.0, light reflectance >85%, colour white, fire performance UK Class 0 / Class 1 (BS 476 Pt-6&7) in module size of 600 x 600 x 15mm suitable for green building application, with recycled content of 66% GW & 74$ RW. The tile shall be laid to Silhouette 15cm face exposed grid, colour white having rotary stitching on all T sections i.e. the main runner, 1200mm & 600mm cross tees with a web height of 32mm and a load carrying capacity of 7.5Kgs/M2 with a minimum pull out strength of 100 kgs. The T sections have a galvanizing of 90 grams per M2 and need to be installed with suspension system complete all as specified and directed. The tile & grid system used together should carry a 10 year warranty. Note: The work shall be executed through authorised applicator of manufacturer.

Supply and fix Welding in repairs thikness of metal exc 6mm but n exc 9mm, exc 2.5cm but n exc 5cm in lengthcomplete all as specified and directed.

Supply & Fix 20mm gun metal gate valves with iron wheel head, screwed both ends for iron pipe and fixed in reapairs complete all as specified and directed.

Supply & Fix in repairs 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (Min wt 210 grams) complete all as specified and directed.

Taking up or down 15 mm dia steel tubing and connections, including cleaning for refixing or removal to store .complete all as specified and directed

Supply and Fix 15mm bore GI pipe Medium grade with all fittings and fixed to wall and ceiling or laid in floor complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connections, including cleaning for refixing or removal to store .complete all as specified and directed

Supply and Fix 20 mm bore GI pipe Medium grade galvanised with all fittings and fixed complete to wall and ceiling or laid in floor complete all as specified and directed.

Cutting chases, pinning in, making good to facings of stone / brick wall where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified and directed

Dismantling of cast iron or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches, if required.

M & L for 100mm dia cast iron sand cast waste and vent pipes in any length with or without ears with cement jointed fixed to wall complete all as specified and directed.

M & L for 100mm dia cast iron Bends complete all as specified and directed..

Taking down eaves gutters and rainwater pipes,PVC (SWR) pipes ( any size or pattern ) including all fittings heads ,shoes, bends, and removal to storecomplete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bend complete all as specified and directed.

Salt glazed stone ware gully trap 150mm square type 'P' includng MS gratings suitable to 150 x 150 mm gully trap and including PCC chamber 10 cm thick and RCC cover set in CM 1:6 complete all as specified and as directed.

Supply & Fix in repairs Vitreous China wash basin, white, flat back, size 580x450mm including brackets, including cutting for and pinning in ends of brackets or erecting stand and including 32mm bore waste coupling of PTMT (half or full threaded) Minimum weight 32mm-45gms/40mm-60 gms) complete all as specified and directed.

Supply and fix in repair long body 15mm bore chromium plated Bib taps, cast copper alloy fancy type, screwed down, screwed for iron pipe or for brass ferrule (minimum weight 550 grams) complete all as specified and directed

Supply & Fix in repair 15mm bore fancy type long (swan) neck Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed (Min wt 650 grams) complete all as specified and directed.

Supply & Fix in repair soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

Supply & Fix in repairs brass chromium plated tabular towel rail 20mm dia complete all as specified and directed.

Supply & Fix in repairs angular stop cock copper alloy, screwed down, high pressure, screwed both ends fancy type chromium plated for 15mm bore Min wt 400 grams complete all as specified and directed.

Supply & Fix in repair Vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) add fixed in repairs including pan cover complete all as specified and directed.

Supply & Fix in repairs white vitreous china squatting pan orissa pattern of size 580mm x 440 mm, with integral foot rest and P or S trap connection to trap and to flushing pipe front or back inlet including, trap and taking out old WC & connections etc complete all as specified and directed.

S&F in repair, 10 ltr capacity low level PVC valveless, syphonic action type flushing cistern (dual system), white, with inlet, ball valve, flush pipe, PVC connection 15 mm dia and 450 mm long float and handle including bracket complete all as specified and directed.

Supply and Fix in repairs PVC connection pipe 15mm dia and 450mm long.complete all as specified and directed

Supply and Fix in repairs 40 mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm ² fixed complete to walls, ceilings or in floors etc. including all pipe fittings. complete all as specified and directed

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) of n exc 15 cm thickness (unreinforced)

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Dismantling of stone slabs and tiles of any description or thickness in floors aprons etc, laid, bedded and pointed in any mortor complete all as specified and directed

M & L Granite slab 20mm thick machine cut, in cooking platform laid over and including cement screed bed 20mm thick in CM 1:4 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types as in urinal partition etc complete all as specified and directed.

M & L Rounding to edges of Granite slab 20 mm thick on one edge, such as in cills, cooking platform, etc and other similar situations complete all as specified and directed.

M & L Machine cut kota stone slab flooring 18-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing including 15mm of screed bed in CM 1:6 complete all as specified and directed.

M & L machine cut kota stone slab flooring 18-25mm thick Except Kota stone over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing including 15mm of screed bed in CM 1:6.complete.

M&L for Mirror polishing on Kota stone / stone work where ever required to give high gloss finish complete all as specified and directed.

M & L 450mm x 300mm x 7 mm thick glazed ceramic coloured tiles as in vertical sufaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles and over 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M & L Non- skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles andover 15mm thick screed or bedding layer in CM 1:6 complete all as specified and directed.

M & L 75 mm thick cement concrete type D2, 1:4:8 (Using 40mm graded stone aggregate) filling sub base as in floors, sub floor etc finished even and smooth all as specified and directed.

M & L 25mm thick cement concrete flooring type B0, 1:2:4 using 12.5 mm graded aggregate finished even and fair complete all as specified and directed.

S & F Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-35 Grade with grey cement and pigment to match the tiles shade all as specified and as directed by engineer in charge

M & L for grit cushioning below interlocking paver block including spreading and levelling complete all as specified and directed.

Material and labour for Cement concrete type B -1, 1:2:4 (20mm graded aggregate) 100 mm thick as in flooring finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for Providing and applying 3 to 3.5mm thick, anti-static, self smoothening flooring on concrete surface having moisture content less than 5%, Electrical resistance of floor surface to earth between 50 Kilo Ohms to 2 Mega Ohms measured with wet electrode. Surface preparation includes grinding of concrete surface, proper cleaning, removing of loose mortar, paint residuals, curing compound residues and existing joints shall be open & joint edges shall be repaired by Epoxy putty followed by application of NITOPRIME 25/ APCOFLOR HFP 130- Epoxy Resin Based Primer for concrete surface using brush or Rooller and allow curing for 8-10 hours (Depending upon Temperature). Mixing of base, hardner, and filler components of NITOFLOOR EU5 / APCOFLOR ESD SL- High stength sel smoothening Epoxy underlay using slow speed Drill and poured on prepared surface at 1.5mm DFT all as specified over copper strip grid work made out of using 25mmx0.5mm thick. copper strips forming One Square Metre grid jointly of surface by pasting suitable adhesive and connect the same to earthing point complete all as specified and directed.

Taking down copper/aluminium flame proof point wiring including Steel conduit pipe (light, fan, socket or power) complete for any height, including switches, sockets etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surface of walls, floors, etc. complete all as specified and directed.

Taking down copper/aluminium flame proof sub main wiring in Steel conduit pipe any type complete for any height removing materials to store for keeping in safe custody for taking credit and making good disturbed surface of walls, floors, etc. complete all as specified and directed.

Taking down unservicable FLP tube light fitting / wellglass fittings complete all as specified and directed.

Taking down flameproof SSC single phase / three phase complete all as directed by Engineer-in-charge

Taking down Unserivecable FLP DB any size

Supply and fix PVC FR-LSH Armoured Copper cable of 1.5 sqmmx 3 core including saddling on wall / surface at any height complete all as specified and directed.

Supply and fix PVC FR-LSH Armoured Copper cable of 2.5 sqmmx 3 core including saddling on wall / surface at any height complete all as specified and directed.

Supply and fix PVC FR-LSH Armoured Copper cable of 4 sqmm x4 core including saddling on wall / surface at any height complete all as specified and directed.

Supply and fix PVC FR-LSH Armoured Copper cable of 6 sqmmx 4 core including saddling on wall / surface at any height complete all as specified and directed.

Supply and fix PVC FR-LSH Armoured Copper cable of 10 sqmmx 4 core including saddling on wall / surface at any height complete all as specified and directed.

S & F Flame proof switch of LM 6 body, rotary switch, SP, 16 Amps for ON / OFF light / fan point to operate on single phase 230 Volts, AC CMRI certified IS-2145 complete all as specified and directed. Make:- Shyam Switchgear Cat Part No-SSPL/2C/1010 or techno commercially equavalent in Flexpro or Baliga

M & L flame proof switch socket combination suitable for 2P+E 16 Amps, 250 volts including plug and top, LM-6 body, CMRI certified, ISI marked complete all as specified and directed. Make:- Shyam Switchgear Cat Part No-SSPL/2C/1010 or techno commercially equavalent in Flexpro or Baliga

S & F flameproof switch socket combination 4P+E (5 Pin) suitable for 32 Amps, 415 volts including plug and top, LM-6 body, certified by CIMFR and PESO , ISI marked complete all as specified and directed. Make:- Shyaam Switchgear Cat Part No SSPL/2C/1010 or techno commercially equavalent in Flexpro or Baliga

Supply and fix flameproof 63 A TPN rotory switch with cable termination box in LM 6 body, CMRI certified, ISI marked complete all as specified and directed. Make:- Shyaam Switchgear Cat Part No SSPL/MCDB/186 or techno commercially equavalent in Flexpro or Baliga

S & F Flameproof LED Well Glass Light Fitting suitable for 90 Watt at any height, product in Aluminum Die casted alloy LM6 IP rating - IP66 of Gas Gr. IIA, IIB Certified by CIMFR Dhanbad with ISI marking with and including all accessories, Led chip, lamp, Driver holders Heat Resistant Clear Toughened ‘Type‐ A’ Glass etc internally prewired complete all as specified and directed. Make: Shyaam Cat no SSPL/1251 or techno commercially equavalent in Flexpro or Baliga

Supply and fixing LED light fitting 2x20 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum housing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etcat any height complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed.complete all as specified and directed. Make: Shyaam Cat no SSPL/FF/1271 or techno commercially equavalent in Flexpro or Baliga

S & F Flameproof LED bulk head 15 watt complete all as specified and directed. Make: Shyaam / Flexpro / Baliga

S & F for taking down flame proof exhaust fan of 300 / 350 mm sweep and repair/rewinding /servicing and refixing at same place after painting of exhaust fans complete in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust and pasting soft stickers indicating MES No of 25 mm size each letter with black synthetic enamel paint etc. complete all as specified and directed.

Supply and fix flame proof bus bar chamber made out LM6 material and high stencil stell hinges and nuts suitable for 415 volts, 3 phase 4 wire 50 Hz AC supply system having 3 Nos aluminium bus bars of 100 amps and Neutral bus bar of 100 amps capacity with necessary insulated bus bar arrangement of 4 strips, cable glands and lugs for incomming and out going cable etc, complete all as specified and directed.

Supply and fix Flame proof Distrubution board made out LM6 material and high stainless steel hignges and nuts Incomer 160 Amps 4 Pole MCCB 25 KA and out going MCB TP 63 A 10 KA- 3 Nos, MCB TP 32 Amps 10 KA-2 Nos with complete inetrnal busbar & wiring upto terminals complete all as specified and directed. Make: Shyaam Switchgear Cat Part No SSPL/RCP/109 or techno commercially equavalent in Flexpro or Baliga.

Supply and fix Flame proof Distrubution board made out LM6 material and high stencil stell hignges and nuts Incomer 32 amps 4P MCB 10 KA and out going MCB SP 6 A 10 KA-15 Nos with complete inetrnal busbar & wiring upto terminals complete all as specified and directed. Make:- Shyaam Switchgear Cat Part No SSPL/RCP/109 or techno commercially equavalent in Flexpro or Baliga

Supply and fix Flame proof Distrubution board made out LM6 material and high stencil stell hignges and nuts Incomer 63 amps 4P MCB 10 KA and out going MCB 4P 32 A 10 KA-04 Nos and MCB SP 16 A- 06 Nos (MCB-L&T / Schneider Make) with complete inetrnal busbar & wiring upto terminals complete all as specified and directed. Make:- Shyaam Switchgear Cat Part No SSPL/RCP/109 or techno commercially equavalent in Flexpro or Baliga

Supply and fix flameproof / weather proof brass nickel plated Double compression cable gland of 3/4 inch (18 mm) size complete all as specified and directed.

Supply and fix flameproof / weather proof brass nickel plated Double compression cable gland of 1 inch (23 mm) size complete all as specified and directed.

Supply and fix flameproof / weather proof brass nickel plated Double compression cable gland of 30 mm size complete all as specified and directed.

Supply and fix 16 SWG HOT DIPPED GALVANISED / POWDER COATED with coupler plates cable tray size 100x 50mm of 2 RM Each length including with nuts, bolts, washers (9G1) and all accessories for mounting and supporting the cable tray system, alongwith vertical bends, bends, if required through wall cutting and making good surface of disturbed area all as specified and directed. Note: Cost of fittings such as vertical supports, tees, elbows, nut bolts and supporting clamps / angle channel etc is deemed to be included in the quoted rates.

Supply and fix 16 SWG HOT DIPPED GALVANISED / POWDER COATED with coupler plates cable tray size 150 x 75mm of 2 RM Each length including with nuts, bolts, washers (9G1) and all accessories for mounting and supporting the cable tray system, alongwith vertical bends, bends, if required through wall cutting and making good surface of disturbed area all as specified and directed. Note: Cost of fittings such as vertical supports, tees, elbows, nut bolts and supporting clamps / angle channel etc is deemed to be included in the quoted rates.

Material & labour for passing through duct/ fixing on wall LT UG cable XLPE Aluminium 1100 Volt 95 Sqmm x3.5 core

Material & labour for Earth contunity conductor or main earthing lead fixed to wall on recessed or burried in ground or drawn in conduit/pipe fixed to poles or any other indicated situation for loop earthing as required 32x6 mm size galvanised strip complete all as specified and directed.

S & F Flameproof 100 mm dia Junction Box 4 way complete all as specified and directed. Make:- Shyaam Switchgear Cat Part No SSPL/JB/105 or techno commercially equavalent in Flexpro or Baliga

S & F FLP flexible metalic hose conduit 20 mm dia 300 mm long for exhaust fan complete all as specified and directed. Make:- Shyaam Switchgear Cat Part No SSPL/FH/145 or techno commercially equavalent in Flexpro or Baliga

Supply & fix Aluminium strip 25mm x 3 mm with saddles and fixing screws etc. for roof conductors and down conductors above ground level fixed on walls / roof with all necessary fixing arrangements complete all as specified and directed including dismantling and taking out old aluminium strip. Note :- Epoxy base insulator and PCC block only will be measured and paid seperately.

S & F Test point terminal block made of gun metal or phosphorus bronze size 75mmx75mmx25mm, drilled and screwed including, 3 NOS, 8mm dia 25mm long hex, head screw complete all as specified and directed including dismantling taking out old inspection box.

Supply & fix galvanised iron of strip 32mm x 6 mm burried in ground or fixed on wall with all necessary fixing arrangements complete all as specified and directed including dismantling taking out old galvanised iron strip. Note :- 1) Epoxy base insulator only will be measured and paid seperately. 2) All GI strip joints should be butt welded atleast 50 mm long.

Supply & fix Air termination, single pointed aluminium rod 12mm dia and 300mm long including dismantling taking out old air termination complete all as specified and directed.

M & L for PCC block of size 150mm x 150mm x 150mm in PCC (1:3:6) type C-1 using with 20mm stone graded aggregate for fixing on roof conductor / air termination rod / GI strip etc. complete all as directed including dismantling taking out old PCC block.

M&L for earthing with galvanised steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground earth pit not less than 2.25 M deep below ground level with top edge of the plate not less than 1.5 M below normal ground level connected to galvanised strip 32mm x 6 mm by means of nuts, bolts, check nuts, washers of galvanised iron or steel all as shown in electrical plate No. 03 of SSR Part I connected to earthing test point including excavation/ earth work in any type of strata, removal of surplus excavated material, GI pipe for watering and funnel, PCC 1:3:6 type C1 chamber including necessary formwork / mould for fair and even surfaces, precast RCC 1:2:4 type B0 chamber cover slab, GI funnel, with GI watering pipe 20 mm bore med gde, wire mesh,with protection pipe 40 mm bore GI pipe light gde for earth lead upto 7.50 m long including testing complete all as specified and directed . Note:- GI earth strip beyond 7.5 mtr in length shall be measured & paid seperately.

S & F earth pit indicator made out of MS sheet of 16 SWG of size 30cm x 20 cm welded to angle of size 25mm x 25mm x 3 mm at a height of 1 M above ground complete all as specified and directed including dismantling taking out old earth pit indicator.

M & L epoxy base insulator of suitable size, 35mm height fixed on PCC blocks/ wall or MS angle/ Pipe or on towers with and including nut bolts and washers etc complete all as specified and directed by Engineer-in-Charge including dismantling taking out old insulator.

S & F inspection boxes / test point boxes 250mm x 150mm x 100 mm made out of 16 gauge MS sheet with top cover including provision of fixing of 2 Nos epoxy insulator with and including insulating PVC sheet for incoming and outgoing copper strip for proper insulation etc complete all as specified and directed.

S & F copper strip 20mmx3 mm as earth countinuity conductor fixed with saddels and fixing screws etc as on wall complete all as specified and directed.

S & F Epoxy based insulator of size 40 mm height fixed on walls/PCC blocks/on floor/on MS angle/on towers etc complete all as specified and directed.

S & F copper plate 150mmx150mmx3mm thick with 1 No. round soild copper bar 20 mm dia & 150 mm long brazed or threaded & fixed in the centre of the plate for manual electrostatic discharge & fixed on existing wall at height of 1.5 mtr complete all as specified and directed.

Material and labour for Earthing in repairs with copper earth plate electrode of 600 x 600 x 3.15 mm thick burried directly in ground, earth pit not less than 2.25mtr deep below ground level with top edge of the plate not less than 1.5mtr below normal ground level connected to 20 x 3.15 mm copper strip by means of nuts, bolts, checking nuts, washers of galvanised iron or steel all as shown in electrical plate No.3 of MES SSR part-I connected to earthing test point including excavation / earth work in any type of strata, watering pipe with funnel, PCC chamber with PCC cover slab without GI protection pipe all as specified and directed by Engineer-in-Charge. Note:- Strip/wire beyond 7.5 mtr in length shall be measured & paid seperately.

S&F copper plate 600mmx600mmx3 mm thick fixed to floor by means of brass nuts / bolts and duly connected to ESDS system complete all as specified and directed.

S & F indicator for electrostatic discharge(ESD) earthing made out of 300x300x3 mm MS sheet fixed on and including 25x25x3 mm angle iron post with PCC 1:2:4 type B1 foundation block and painting exposed surface with two coats of syenthetic enamel paint over coat of red oxide primer and writing letters for indication of ESD earthing complete all as specified and directed.

Mourya Construction

Mehta Construction Co.

VIRENDRA FABRICATORS