COMPREHENSIVE MAINT AND CERTAIN OTHER MISC BR AND EM WORKS AT ZONE A AREA AND CAMP AREA UNDER AGE BR II OF GE SUKNA

Amount

M&L PCC 1:2:4 type B-1 (using 12.5 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M&L for 25 mm thick (measured solid) Jallies or louvers Precast Reinforced Cement concrete 1:2:4 type B0 (Using 12.5 mm graded stone aggregate) in including all mouldings set jointed in CM 1:4 but excluding frame including demolition of existing cement concrete complete all as specified and directed.

M & L for providing Reinforced cement concrete (1:1.5:3) A-1 Nominal Mix using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m span and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately.)

Supply only integral water proofing compound complete all as specified.

M&L PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in gap between roof sheets and brick wall, thickness of concrete bed exc. 5 cm and not exc.10 cm thick & width not exc. width of one brick thick wall including necessary scaffolding and formwork ht up to 7 m complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like laid over and including screed bed 15 mm thick in CM 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and complete all as specified and directed.

M&L 18 to 20 mm thick granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including making rebate for fixing second shutter as per site requirement complete all as specified and directed.

S & F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F 30 mm thick flush door shutters solid core construction, with block board core and plywood face fanels, commercial type on both side with decorative face veneer with liping/frame to match complete all as specified and directed.

S&F 30 mm thick flush door shutters solid core construction, with MDF board exterior grade, commercial type on both side and covered on both side with decorative face veneer with liping/frame to match complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down and refixing in the same opening shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc complete all as specified and directed.

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of wire gauze in lieu of plain colour PVC sheet. The wire gauze shall be wrapped on an additional square 8mm MS Solid tube and this tube shall be welded to MS tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

M&L for 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining,Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site as per specification and drawing given on MES schedule standard of rate 2020 complete all as per specified and as directed by Engr-in-charge.

S&F 5 mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 5 mm thick PVC insulation panel with EPS stuck to 1 mm plain PVC sheet suitably placed in false ceiling including GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (n. exc. 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel at 457 mm centre to centre and necessary hangers 6 mm dia GI fixed to roof complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S & F in repairs MS Helical door spring 150 mm size including roller and roller plate fixed to wooden or steel frames with welding etc complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repairs mortice locks suitable for aluminium door of 100 mm size 4 lever aluminium body vertical type as per existing or sample complete all as specified and directed.

S&F in repairs Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width of and of weight between 61 to 80 Kg. (extruded section) complete all as specified and directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

Supply and fix in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S & F Mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tank and similar work confirming to Fe-290 Gde E-165 Complete all as specified and as directed by Engr-in-Charge.

M&L for mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 5 mm to 10 mm dia.,cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S & F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Structural steel work of angle, channel etc., confirming to Fe 410 -W (Gde- E- 250)complete all as specified and directed.

S & F of structural steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 including fabrication complete all as specified and directed.

S&F in repair steel rolling shutters without ball bearing, with thickness of laths 1.00 mm push and pull or mannual type including top cover, anchoring rod, hasp and staple with one shop coat of red oxide or zinc chrome primer and fixed in position complete all as specified and directed.

S&F Safety lever locks mild steel with 4 levers including locking plate for rolling shutter complete all as directed.

S&F Ball bearing of suitable sizes complete for rollong shutter complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dove-tailed or welded complete all as specified and directed.

S&F steel ventilator with top hung shutter and including hinges steel peg stay complete all as specified and directed.

S&F 150 mm floor door stopper of brass body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F Powder coated aluminium frame (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

S&F in replacement 4 mm thick E-board (designer pattern) celing of size 60x60 cm, fixed or laid / inserted to with and including aluminium framework with screws in false ceiling (flat or sloping) of grid size 605 x 605 mm and with and including anodised aluminium snap grid with 25x25x1.5 mm thick Tee section and 38x25x2 mm thick angle for false ceiling Hangers with 6 mm dia. G.I. (length as required) adjusting level fixed to roof slabs/truss by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed including necessary dismantling of existing unserviceable ceiling boards of any thickness incl cover fillets complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

M&L machine cut kota stone slab 20-25 mm thick as in slab flooring, laid over and including 15 mm thick screed bed in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the stone complete all as specified and directed.

M&L machine cut kota stone slab 20-25 mm thick as in skirting, dado, riser of steps, plinth, etc, laid over and including 20 mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the stone complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as plinth protection Construction joints to be given at every 3M interval and Corners of buildings and filled with bituminous mastic or equivalent filler complete all as specified and directed.

M&L 75 mm thick, PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub floor, sub base of floor, etc complete all as specified and directed.

M&L rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in skirting/dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick backing in CM 1:3 complete all as specified and directed.

M&L Coloured glazed ceramic tiles 350x 250x 7 mm/ 450X 350X 7mm thick in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick backing with cm 1:3 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 finish even and rough complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, as in skirting/dado on vertical surfaces over etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:4 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.18 sqm but n. exc. 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm in cement mortar 1:4 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.18 sqm but n. exc. 0.36 sqm, as in skirting/dado on vertical surfaces over etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including backing 10 mm in cement mortar 1:3 complete all as specified and directed.

M&L 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour,design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra Sand complete all as specified and directed.

M&L cement concrete chequered tiles 300 x 300 x 25 mm thick with grey cement with pigment, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces as in floors laid over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished the surface even and smooth without using extra cement complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or stone masonry or on one side of lathing surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M & L for preparation of newly plastered or previously untreated surfaces of walls and applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty complete all as specified and directed.

M&L preparation of old decorated wall surface and including applying one coat of oil bound distemper complete all as specified and directed.

M&L preparation of old plastered wall surfaces and inlcuding applying one coat of weather coat exterior paint complete all as specified and directed.

M&L for preparation of new plastered wall surfaces and including applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed.

S & F 4 mm thick Frosted / Pin headed glass, ordinary type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane fixed to steel frame including steel pin complete all as specified and directed.

S&F 4 mm thick glass including tinted/dark film exc 0.5 sqm each pane complete fixed to aluminium frame work including rubber beading complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from steel/wooden frames or stones, concrete or brick surrounds glazed with oil putty or fixed with beads complete all as specified and directed.

M&L preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) complete all as specified and directed.

M&L preparation of old decorated steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor and including taking down of existing pipe complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor and including taking down of existing pipe complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 500 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), including 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of 500 ltr to 1000 ltr capacity PVC water storage tank without dismantling the tank incl writting the item "Tank Cleaning on ____" indication the date, month & year of cleaning on external wall of tanks walls with synthetic enamel paint all as specified and directed by Engr -in-charge.

S&F in replacement 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

Dismantling wall and ceiling boards, partitions of any description or in any position (fibre, pulp, insulation etc.) any thickness, or insulation boards/ slabs/ blankets of any thickness including cover fillets complete all as specified and directed.

Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed by Engr-in-Charge.

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, modular plate and frame on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch, all necessary cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. Note :- (i) Making good to match with the adjoining surface shall be included in the unit rate. (ii) Cutting chases shall be included in the unit rate.

All as per Sl. item No. 98.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on same board.

All as per Sl. item No. 98.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on independent board.

All as per Sl. item No. 98.00 above but for one light point controlled by two, 2 - way switches complete all as specified and directed

All as per item No. 98.00 here-in-before but one 3 pin socket outlet / 15 amps on the independent board with other switches, with cables 2.5 sqmm size complete all as specified and directed

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including PVC casing caping (double lock pattern) and accessories on wall / ceiling surfaces etc. with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc including all other fixing accessories for one light / fan / exhaust fan point controlled by one 5 / 6 Amps switch complete all as specified and directed.

All as per Sl. item No. 103.00 above but for one 3 / 5 Amps socket outlet point on the same board.

All as per Sl. item No. 103 above but for one 3 / 5 Amps socket outlet point on independent board.

All as per Sl. item No. 103.00 above but for one light point controlled by two, 2 - way switches complete all as specified and directed

All as per item No. 103.00 here-in-before but one 3 pin socket outlet / 15 amps on the independent board with other switches, with cables 2.5 sqmm size complete all as specified and directed

M & L concealed sub main wiring with 2 runs of 2.5 sqmm main wire along with 1 run of 2.5 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces and including taking down complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L concealed sub main wiring with 2 runs of 4.00 sqmm main wire along with 1 run of 4.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces and including taking down complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L concealed sub main wiring with 2 runs of 6.00 sqmm main wire along with 1 run of 6.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces and including taking down complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L concealed sub main wiring with 4 runs of 10.00 sqmm main wire along with 1 run of 10.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces and including taking down complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

S&F switch piano flush type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano flush type one way, 15 / 16 Amps, 240 volt complete all as specified and directed.

S&F Switch piano flush type 5 Amps single pole two way complete all as specified and directed.

S&F switch piano modular type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano modular type two way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano modular type one way, 15 /16 Amps independent, 240 volt complete all as specified and directed.

S & F Socket outlet 5 Amps 3 pin flush type complete all as specified and as directed.

S&F switch socket outlet 3 pin 15 Amp, flush type universal complete all as specified and directed.

S&F socket outlet modular type 3 pin 5 / 6 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F socket outlet modular type 3 pin 15/16 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F switch socket combination 3 pin 15 Amp, flush type universal complete all as specified and directed.

S&F switch socket combination 5 pin 6 Amp, flush type universal complete all as specified and directed.

S&F ceiling rose, surface bakelite 65 x 50 mm three terminal complete all as specified and directed.

S&F lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and as directed.

S&F in repair stepped type electronic fan regulator 450 watt, two module, with 5 step, AC 50 Hz 240 Volts grade complete all as specified and directed.

S&F in repair electronic modular fan regulator, stepped type, white 120 W - 2 module complete all as specified and directed.

S & F Bell push, flush type, 5 Amps single pole complete all as specified and as directed.

S & F Bell, AC 230 Volts single pole complete all as specified and as directed.

S & F Bell multi music type, AC. 230 volts, single pole completed all as specified and directed.

S&F modular type Bell push 6 A , 1 module complete all as specified and directed.

S &F Bell buzzer, Ding Dong AC. 230 volts, single pole completed all as specified and directed.

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 6 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver including all fixing arrangement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- ZIVAFLRDDLR6WLED840S or equivalent Make of Philips / Crompton .

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 9 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- ZIVAFLRDDLR9WLED857S or equivalent Make of Philips / Crompton .

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 15 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- ZIVAFLRDDLR15WLED840S or equivalent Make of Philips / Crompton .

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 18 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- edgeprorddlr18WLED840SG2 or equivalent Make of Philips / Crompton .

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 24 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- ZIVAFLRDDLR24WLED857S or equivalent Make of Philips / Crompton ..

S&F in replacement Recessed Mounted Square (2'x2') LED Panel light 36 watt with CRCA powder coated housing & high transmittance Opal diffuser for glare free with Electronic LED Driver. IP20, PF =0.95, System Lumens =120 lm/W, 5700k CRI = 80, Operating Voltage range 140 V - 270 V.complete all as specified and directed.

S & F in repairs Surface and wall mounted LED batten 10 watt 2ft long with Aluminum extruded housing , high quality polycarbonate diffuser & integrated Electronic Driver with IP20, PF 0.90, Efficiency not less than 110 lm/W color temp 6500k CRI = 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed.

S & F in repairs Surface and wall mounted LED batten 20 watt 4ft long with Aluminum extruded housing , high quality polycarbonate diffuser & integrated Electronic Driver with IP20, PF 0.90, Efficiency not less than 110 lm/W color temp 6500k CRI = 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed.

S & F in repairs LED Bulk Head fitting 10 watt with Injection molded polycarbonate housing IP66, IK10, 3.5kV inbuilt surge protection, PF =0.95, total System Lumens not less than 1100 lm, 6500k CRI = 80, Operating Voltage range 140 V - 270 V. complete all as specified and as directed.

S&F in repair VTPN DB,MCCB incomer,4 ways double door,Metal door ,IP-54 IK 09 in 250A rated copper bus bars,earth bar,neutral links, no. of module DPX 160 complete including blanking plates as required & fixed flush to wall and making good the disturbed surfaces including taking down old unsv ones complete all as specified and as direct. Make: Cat ref 507750 of Legrend/L&T or equivalent.

S&F in replacement Double door TPN DBs 4 Way, of powder coated DB's suitable for MCB's fitted with bus bar, neutral link, earth bar and Din ral & DB's will be fitted concealed in wall / surface as per site required complete all as specified and directed.

S&F MCCB 4 pole 125 Amps breaking capacity 25 KA, Ics = 100% Icu including spreader link complete all as specified and directed.

S&F MCB TPN 40 to 63 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F in replacements MCB ,SPN DB, 08 ways double door, Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete including. blanking plates as required & fixed flush to wall and making good the disturbed surfaces complete all as specified and as directed

S&F in replacements MCB ,SPN DB, 12 ways double door,Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces complete all as specified and as directed

S&F MCB SP 6 to 32 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB SPN 40 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F in repair Metal Plug Socket DB with sheet metal enclosures with two pin and earth plug and socket one double pole MCB 20 Amps,240V for Geysor connenction complete all as specified and as directed.

S&F ventilation fan 200 mm sweep, non metallic plastic body, AC single phase, 230 V, 50Hz with & including self closing louvres, nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to exhaust fan and writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole and making good the disturbed surface to match the existing surface complete all as specified and directed. (Note-Old fan shall be deposited to MES storeyard without any extra cost.)

S&F ventilation fan 250 mm sweep, non metallic plastic body, AC single phase, 230 V, 50Hz with & including self closing louvres, nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to exhaust fan and writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole and making good the disturbed surface to match the existing surface complete all as specified and directed. (Note-Old fan shall be deposited to MES storeyard without any extra cost.)

S&F wall mounted fan 400 mm sweep, non metallic plastic body, AC single phase, 230 V, 50Hz with & including nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to fan and writing MES number in 2 cm height with synthetic enamel paint and fixing on wall and making good the disturbed surface to match the existing surface complete all as specified and directed. (Note-Old fan shall be deposited to MES storeyard without any extra cost.)

M &L in replacements Earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick, buried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connected using galvanised iron earth lead wire 4 Sqmm as earthing electrode by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe (medium grade) and other end connected to earthing test point as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C both ways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth up to a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 5 of MES Schedule Part-I complete including testing on completion. On testing after completion if the desired earth resistance is not obtained the earthing will be made again by the contractor at no additional cost complete all as specified and directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 12W complete all as specified and directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 15W complete all as specified and directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 18W complete all as specified and directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 24W complete all as specified and directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 36W complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 100mm x 100mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 175mm x 100mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 200mm x 150mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 250mm x 200mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 350mm x 300mm x 50mm size complete all as specified and directed.

S & F in repair wall light of single head of with 9 watt LED lamp of base B-22 inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Philips / Havells/ Crompton .

Supply Installation and commissioning in repairs of single phase, 2 wire LCD display energy meter of rating 5-30 amps, 240 volts, 50 Hzaccurecy class 1.0 with optical port including box energy meter of rating 5-60A, 240 volts, 50 Hz accuracy class 1.0 including all fixing arragnement and electrically connecting complete all as specified and directed. Note : - The quoted rate is including for taking down and depositing old meter to MES Store Make :- L&T Cat No – WM101BC5DDHBOX or equivalent

D K SARKAR (BID ID -3487274)

M/S B B CONSTRUCTION (BID ID -3489119)

ELECTRO WIR WAY (BID ID -3490067)

DEBABROTA ROY CHOWDHURY (BID ID -3491035)

MS ESSCON (BID ID -3489978)

M/S GLORIOUS CONSTRUCTION (BID ID -3490570)

R K UDYOG (BID ID -3490657)

Janata Enterprises (BID ID -3488692)