SPL REPAIR TO USFM GP AT 509 ABW UNDER GE (EAST) AGRA

Amount

Dismantling asbestos cement (corrugated, semicorrugated sheet/ North light curve, Ridge etc.) sheets in roof coverings complete all as specified and directed.

S&F of Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified complete all as specified and directed.

S&F of Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S&F Plain, galvanised, mild steel sheeting, 1.25 mm thick in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 fixed with self tapping screws as specified complete all as specified and directed.

Dismantling of wrought iron of mild steel work of any description not otherwise poivided.

S&F of Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, wind tie,channel or flat sections) including distance pieces, welding, cutting , cleats etc Fe 410 -W (GdeE- 250) qualityA complete all as specified and directed.

S&F for Mild steel framed work as in chowkhat / frame of doors or gates of angle or other section with gusset plates, rails, braces,hold fast etc., complete all as specified and directed., drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete, quality conforming grade Fe- 290 or E- 165 complete all as specified and directed.

M&L for Preparation of new steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed

M&L for Preparation of old steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for Surfaces of New wood surface of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coat of creosote oil etc complete all as specified and directed.

Dismantling wall and ceiling board or insulation board /slabs/blanket any thickness including cover fillets / frame etc complete all as specified & direted.

S&F 605x605mm snap grid of powder coated galvanized iron of angle of size 23mm x 23mm of 30 gauge (Perimeter), T section of size 23mm x35mm main and 23 mm x 27 mm (intermediate) of 30 gauge suitable for false ceiling including GI wire 2 mm thick @ 1200 mm centre to ceter both ways for hanging arragement complete all as specified and directed

M&L for 4 mm thick non asbestos fibre cement building board designer as in ceiling of size 600 x 600mm fixed to GI snap grid frame work complete all as specified & directed.

Taking down chowkats or frame with shutter (without taking off shutters from the frame) not exc 1.5 Sqm each complete all as specified and directed.

All as per item No 15. before but exc 1.5 Sqm and not exc 4.00 Sqm each complete all as specified and directed.

S&F anodized / Powder Coated aluminium door & frame 0.55 Kg/m incl- 5.00mm thick tinted glass in half portion and in other half portion 12 mm thick prelaminated particle board, exterior grade prelaminated one side with decorative choice lamination & other side balancing white lamination complete and fixed with anodized aluminium snap beading, glazing clips, joining clips, screws and 02 Nos of aluminium handle on each door shutter, aluminium anodized tower bolt 200 mm long 02 Nos on each shutter and martice lock device complete with double keys for each lock, 01 No Floor spring for each shutter complete all as specified and directed with following specifications:- (a) Aluminium door frame = 101.50x44.45mm (b) Aluminium style/top & middle rails of shutter = 83.5x44.45mm (c) Aluminium bottom rail of shutter = 114.50x44.45mm (d) Aluminium door frame with shutters shall be fixed in position in brick wall opening as required according to site conditions including all fastening arrangements & making good of existing surface with obd/whitewash over plaster after fixing door etc complete all as specified and directed

S&F tubular steel framed work as in chowkhat / frame for single door frame of size 100 x 50 mm & thickness of tubular section not be less than 2.5 mm for doors with one or more rebates including necessary fixing lugs, lock, strike plate,hold fast etc complete all as specified and directed.

S&F Factory made flush shutter 35 mm thick solid core construction with block board core and plywood face panels commercial type complete all as specified & directed.

S&F 200 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified & directed.

S&F Aluminium alloy, anodised, 250 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F Mild steel butt hinge medium weight cold rolled of size 100 mm long and fixed with screw/ welding complete all as specified and directed.

S&F 150 mm long aluminium anodized handle cast type complete all as specified and directed.

S&F Floor door stopper 150 mm long of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor complete all specified and directed.

Providing & fixing of windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy-duty stain less steel pivot hinges shall be provided per shutter. The windows should be panelled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self-expanding, screws. Including 10mm square guard bars with 6” (152.4mm) pitch including making good of existing surface with obd/whitewash over plaster after fixing window etc complete for finished item of work including of all taxes etc as specified and directed.

Providing and Fixing of ventilator made of pre-painted steel (Base steel as per IS 513 of 0.58 mm thick “D” Quality galvanized as per IS 277 with Zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 48x50mm, centre mullion should be of 48x50mm, section for shutter should be of 52x 25mm and rebate for Glazed shutter with a 20mm provision for Guard bars/Grills. The sections are to be cut to length metre joined with corner bracket. Centre mullion is to be fixed with mullion cap. Handle, stay, 2 nos. of Stainless Steel heavy duty Pivot hinges shall be provided per shutter the windows fitted with 4 mm thick plain float glass with rubber gaskets including fixing the frames in concrete/masonry wall by means of self expanding screws, Including fixed panel beading section should be of 12x12mm. Outer frame and mullions to have 10mm Square guard bars with 6” (152.4mm) pitch etc.complete for finished item of work.

Hacking out old broken glass (any thickness, size quality or description) from wooden or metal frames, glazed with putty or fixed with beads etc complete all as specified & as directed.

S&F Rough Cast wired Figured glass 6.4 mm thick and glazing with oil putty in squares not exceeding 0.5 Sq. M in each pane complete all as specified and directed.

S&F in repair powder coated aluminium partition of specified aluminium section as per required size & Wt. of section can not be less than 0.55 Kg / Rm including aluminium beads, rubber gasket and 5 mm thick Plain glass in upper portion and 8 mm thick ACP sheet of any colour etc complete all as specified and directed.

S&F in repair steel rolling shutters 1.25 mm lath thickness with ball bearing,as specified including top cover, anchoring rod, hasp and staple,rail and gear operated type with bevel gear box and crank handle to make it fully functionable etc complete all as specified and directed.

Taking down cement or cement lime plaster of any discription on bricks or stone walls/ceiling etc including racking out joints, hacking for kay, scrubbing down with water.

M&L for 15 mm thick plastering in CM 1:6 on brick surfaces of walls & finishing the surface even & smooth complete all as specified and directed.

M&L for 15 mm thick plastering in CM 1:4 on brick surfaces of walls & finishing the surface even & smooth complete all as specified and directed.

M&L for two coats of oil bound distemper over a coat of average 2 mm thick putty on new plastered surfaces including preparation complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over 2 mm thick putty and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on new surfaces complete all as specified and directed

Demolition of brick work built in cement mortar including all quoins arches pillar etc complete all as specified and directed.

M&L for brick work with subclass B bricks old size straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Preparing old plastered or unplastered surfaces of walls by brooming down or by steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts and applying two coats of oil bound distamper over 2 mm thick putty complete all as specified and directed.

Material and Labour for preparation of old plastered or unplastered surfaces of wall including cornices, pilaster etc by brooming down by steel wire brushing, scrapping down smoke Soot, moulds, moss and trading oil and greasy spots etc and apply two coat of white wash complete as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on old surfaces incl. preparation of surfaces over 2 mm thick putty etc complete all as specified and directed.

M&L for preparation of old Surfaces of wall any description over 10cm girth or width, not otherwise described and applying a coat of synthetic enamel paint etc complete all as specified & directed.

Dismantling stone slabs and tiles of any description or thickness in floors / dados, etc laid bedded and pointed in any mortar complete all as specified and directed by the Engineer-in-charge

M&L for Machine cut kota stone slab flooring 20-25 mm thick incl preparation of surface and over cement screed bed 20 mm thick in 1:6 cement and sand mortrar, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L for Kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over and incl 10 mm thick cement plaster 1:4 cement and sand mortrar all as specified and directed.

M&L for Virified Ceramic tiles, light shade 10 mm thick (square/ rectangular) polished, area of each tiles n exc 0.42 sqm but not exc 1 sqm in floors etc white cement and coloured pigment to match the tiles over 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Ditto all as per item no. 46 but in skirting over 10 mm thick rendering in CM 1:4 etc complete all as specified and directed.

Demolition of cement concrete of any description and any position etc all as specified & directed.

M&L for PCC 1:2:4 Type B1 ( using 20 mm graded stone aggregate), in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in eight, copings, kneelers, apex stones bed plates, kerbs chajjas , water troughs, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating, fixing of chain link fencing etcall as directed incl necessary formwork etc complete all as specified and directed.

M&L for Cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 etc complete all as specified and directed.

S&F in repair PVC (SWR) pipes single socketed 200 mm bore, incl bend, shose, Tee, Y, as required, etc in any length with rubber ring joints fixed to walls with MS clamp all as specified and directed.

M & L hard core of broken stone or boulder having gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thk, watered and rammed to a true surface, complete all as specified and as directed.

M&L for Cement concrete type B-1, 1:2:4 (20mm graded aggregate) 40 mm thick including even and smooth finish etc complete all as specified and directed.

M&L 75 mm thick PCC (1:3:6) type C1 using 40 mm graded stone agg as in plinth protection / Path /Sub base/ paving surface / Hard Standing etc even and smooth and and exposed edges fair or rounding or chamfering laid in panels with and including all necessary form work and filling the joints with mastic filling of one part of hot bitumen 85/25 grade and three part of fine sand (all by weight) complete all as specified and directed.

Demolition of Reinforcement Concrete of any description and in any position etc all as specified & directed.

M&L providing precast cement concrete Type B1 1:2:4 (20mm graded aggregate) (nominal mix) for cover slab for manhole, drain and similar articals with plane faces complete all as specified and directed by engineer-in-charge.

S&F TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified & directed.

M&L for 1.00 mm thick mild steel black sheet as in steel gate and similar works cut to size, holes punched including round headed screw welded etc including Two coats of synthetic enamel paint (Ordinary tint) over a coat of red oxide primer including preparation of new or previously untreated surfaces of steel complete as specified and as directed.

M&L RCC M-25 (20 mm graded stone aggregate) as in roof beams, chajja lintle etc complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, in fair finished etc. all as specified and directed

S&F mild steel bars 5 mm dia and over up to 10 mm dia in stirrups space and binders. (TMT) cut to length bent to shape required including cracking,bending spirally for hooping ends and binding with and including mild steel wire not less than 0.90 mm dia quality of steel etc complete all as specified and directed.

Taking down copper / aluminum point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, fan regulators, sockets, lamp holder, bell push, call bell, LED bulb, light fitting etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L point wiring with 1.5 sqmm multi stranded copper conductor 1100 volts. grade FRLSH PVC insulated unsheathed cable with proper colour coding drawn in including PVC concealed conduit medium grade not less than 20 mm dia with all accessories and FRLSH PVC insulated 1.5 Sqmm multi standard unsheathed copper wire for continues earth, GI sunken boxes 60 mm deep & 1.6 mm thick duly painted with aluminium inside and anticorrosive paint out side, including 3 mm thick plastic laminated sheet for mounting switches, socket, fan regulators etc connecting earth and making good to the disturbed surface of wall / floor and matching with existing specifications, connection of cable with MCB's or bus bar shall be done through proper size copper / brass thimbles. Note :- Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit is not feasible at no extra cost for the following (a) One light /fan point controlled by one switch.

(b) One 5 pin socket outlet 5 Amps on same board

All as per item No.58 above but one 3 pin socket outlet, 5 Amps on independent board with cables 2.5 sqmm copper conductor complete all as specified and directed.

All as per item No.58 above but with 4 sqmm multi stranded copper conductor 1100 volts grade FRLSH PVC insulated sheathed cable with FSLSH PVC 4 Sqmm multi stranded insulated unsheathed copper wire for continues earth on independent board complete all as specified and directed.

Supply and fix switch piano flush button single pole one way 5 amp 240 volts with polycarbonate body complete all as specified and directed.

Supply and fix switch piano flush button single pole one way 15 amp 230 volts with polycarbonate body complete all as specified and directed.

Supply and fix socket 5 amp 5 pin flush type, 240 volt with polycarbonate body complete all as specified and directed.

Supply and fix socket out let, 6 pin 5 and 15 amps multi purpose 2 in 1 flush type, 230 volts with polycarbonate body complete all as specified and directed.

Supply and fix stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc as required complete all as specified and directed.

Supply and fix ceiling rose, PVC / polycarbonate, insulated body surface bakelite 65 mm dia three terminals complete all as specified and directed.

Supply and fixing LED luminaire 595 mm x 595 mm, 40 watt, 220 V AC, 6500 K recessed type with igh efficiency PMMA diffuser soft glare free light complete with driver, holder & LED lamp suitable for roof ceiling including connecting up with driver and connecting the same to eletric source with & using PVC sheathed and insulated three core copper conductor cables of size 0.75 sqmm and fixing arrangement for fixing the light fitting complete all as specified and directed.

Supplying and fixing LED battan Tube light 20 watt surface / wall mounted with specially designed powder coated aluminum housing, high optically efficient polycarbonate diffuser, in built electronic driver duly wired upto terminal block, power consumption < 20W, luminaire lumens > 2000 lm, system efficiency of > 120 lumens / W, with LED binning as per AMSI Bin C 78.377A, photo biological safety report as per IEC 624718 & electrical insulation class I, ingress protection IP 20, colour rendering index CRI > 80, temp range 0 to 450C, driver efficency > 85%, power factor > 0.9, THD <20% as per IEC 61000-3-2, colour temp 6500K, surge protection 2.5 KV, 50000 burning hrs (min) as per L70 criteria, two stages isolated constant current operated driver with range 150 - 270V AC and seafty extra low voltage safe level < V DC as per IEC standard with LM 70 & LM 80 certification complete all as specified and directed.

Supply & fixing LED building security light fitting 35 watt 230 V AC out door type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, fixed to pole or wall of building and including suitable bracket made out of 25 mm dia GI light grade pipe, 1.00 m long bent to shape by cutting & welding as required & directed and fixed with tow Nos of FI clamp 35 x 6 mm to tightened with suitable size of botls, nut and washer and including painted with two coat of aluminium paint over a coat of red oxide primer and including connecting the fitting to eletric source with & including twin twisted copper flexible wire of size 0.75 sqmm three core with suitable size flexible PVC conduit including all accessories and fixing arrangement for fixing the light fitting and writing the date of fixing on security light with permt marker complete all as specified & directed.

Supply and fixing LED High Bay light fitting 50 watts with necessary hanging arrangement including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single phase 230 V, heavy duty (copper winding) of size 450 m sweep, 1400 RPM with, blades and frame and louvers incliding cutting of round hole of suitable size as per size of exhaust fan and make in good to the disturbed surface MS bolts, grouted to wall and connecting up including provision in cable from connector to fan with flexible cable 24/0.2 mm with copper conductor and necessary fitting arrangement complete all as specified and directed.

Dismantling taking down existing ceiling fan and re-fixing & connecting up including provision of cable from ceiling r ose or connector to fan complete all as specified and directed.

S&F sheet metal enclosure with socket plug top and MCB single pole and neutral with two pin and earth plug top with one SP MCB 20 Amp 240 volt incl cutting / Chasing of wall and making in good to the disturbed surface complete all as specified and directed.

Supply & fix of sheet metal enclosure vertical TPN DB 4 way double door, suitable for flush mounting and surface mounting, with 250 A copper busbar for each phase with 2 Neutral bar, 2 Earth bar and cable ties for cable management, fully insulated busbar & shrouded neutral bars, improved pan assembly for ease of installation, prefitted masking sheet, reversible door for IP 43 DB with provision for 160 Amp MCCB as incomer and SP / TP MCB as outgoing including taking down of old unsv MCB DB, cutting / chasing of wall and make in good to the disturbed surface complete all as specified and directed.

Supply & fix sheet metal enclosure MCB distribution board, TPN 415 volt 6 way with IP-43 protection double door complete with appropriate size bus bar and neutral link fixed flush in wall including chases wall for fixing DB and taking down of old MCB DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

Supply & fix sheet metal enclosure MCB distribution board, single pole & neutral 240 volts 12 way with IP-43 protection double door complete with appropriate size bus bar and neutral link incl taking down of old unsv MCB DB, cutting / chasing of wall and make in good to the disturbed surface complete all as specified and directed.

Supply & fix sheet metal enclosure MCB distribution board, single pole & neutral 240 volts 8 way with IP-43 protection double door complete with appropriate size bus bar and neutral link incl taking down of old unsv MCB DB, cutting / chasing of wall and make in good to the disturbed surface complete all as specified and directed.

Supply & fix sheet metal enclosure MCB distribution board, single pole & neutral 240 volts 4 way with IP-43 protection double door complete with appropriate size bus bar and neutral link incl taking down of old unsv MCB DB, cutting / chasing of wall and make in good to the disturbed surface complete all as specified and directed.

Supply and fixing in repair one way sheet metal enclosure suitable for MCCB, 4 pole, 250 Amps, As per IEC 61439-3 complete all as specified and directed.

Supply and fixing MCCB 4 pole, 250 Amps, 50 Hz, Icu=35 KA at 415 volts with thermal magnetic alongwith adjustable magnetic protection for current setting Icu = Ics=100% with adjustable over load setting (minimum 70% to 100%) value from 10 to 15 times of related capacity standard complete all as specified and directed.

Supply and fixing MCCB 4 pole, 160 Amps, 50 Hz, Icu=35 KA at 415 volts with thermal magnetic alongwith adjustable magnetic protection for current setting Icu = Ics=100% with adjustable over load setting (minimum 70% to 100%) value from 10 to 15 times of related capacity standard complete all as specified and directed.

Supply and fixing MCB SP-5 to 32 Amp rating 240V, 10 KA 'C' curve and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing MCB SPN 40 to 63 Amp rating 240 V, 10 KA 'C' curve and current carrying capacity in the MCB DB complete with connection testing and commissioning Complete all as specified and directed.

Supply and fixing MCB TPN 100 Amps, 415V 10KA 'C' curve and current carrying capacity in the DB complete with connection testing and commissioning. complete all as specified and directed.

S&F sub main wiring with two single core FRLS PVC insulated unsheathed multistranded flexible copper conductor cable of size 2.5 sqmm and one single core PVC insulated multistranded unsheathed flexible copper conductor 2.5 sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in PVC conduit heavy grade not less 20 mm dia including dismantling of old unsv submain wiring complete all as specified and directed by Engr in charge including taking down existing un serviceable sub main wiring complete Note :- (i) The work should be executed at the top of appx 25 m height of building. (ii) Two run of single core PVC cable with one run of earth conductor and conduit / batten shall be measured as one unit.

S&F sub main wiring with two single core FRLS PVC insulated unsheathed multistranded flexible copper conductor cable of size 4 sqmm and one single core PVC insulated multistranded unsheathed flexible copper conductor 4 sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in PVC conduit medium grade not less 20 mm dia including dismantling of old unsv submain wiring complete all as specified and directed by Engr in charge including taking down existing un serviceable sub main wiring complete Note :- Two run of single core PVC cable with one run of earth conductor and conduit / batten shall be measured as one unit.

S&F sub main wiring with two single core FRLS PVC insulated unsheathed multistranded flexible copper conductor cable of size 6 sqmm and one single core PVC insulated multistranded unsheathed flexible copper conductor 6 sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in PVC conduit medium grade not less 25 mm dia including dismantling of old unsv submain wiring complete all as specified and directed by Engr in charge including taking down of existing un serviceable sub main wiring complete Note :- Two run of single core PVC cable with one run of earth conductor and conduit / batten shall be measured as one unit.

S&F sub main wiring with four single core FRLS PVC insulated unsheathed multistranded flexible copper conductor cable of size 10 sqmm and two single core PVC insulated multistranded unsheathed flexible copper conductor 10 sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in PVC conduit medium grade not less 25 mm dia including dismantling of old unsv submain wiring complete all as specified and directed by Engr in charge including taking down of existing un serviceable sub main wiring complete Note :- Four run of single core PVC cable with two run of earth conductor and conduit / batten shall be measured as one unit.

S&F sub main wiring with four single core FRLS PVC insulated unsheathed multistranded flexible copper conductor cable of size 16 sqmm and two single core PVC insulated multistranded unsheathed flexible copper conductor 1x16 sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in PVC conduit medium grade not less 32 mm dia including dismantling of old unsv submain wiring complete all as specified and directed by Engr in charge including taking down existing un serviceable sub main wiring complete Note :- Four run of single core PVC cable with two run of earth conductor and conduit / batten shall be measured as one unit.

Supply & Fix Air circulator fans 230 volts single phase oscillating 600 mm sweep, min 1440 RPM suitable for wall mounting complete all as specified and directed.

S&F wall mounting fan, electric driven single phase 230 volts, oscillating type, 400 mm sweep, high quality ABS base with high speed motor and balanced blades with three leafed and 3 core copper cable of suitable size complete all as specified and directed.

Supply, fixing, connecting & testing BLDC ceiling fans operated with remote control complete with blades, down rods 3 mtr length, remote control and accessories, 230 V, 1200 mm sweep, min air delivery 210 CFM with service value 6.00 BEE five star rated with brushless direct current motor (BLDE) and including connecting wire with new 3 core 0.50 Sqm PVC insulated and sheathed copper conductor cable from ceiling rose and also wiriting MES No with black paint complete all as specified and directed.

M&L for earthing complete with galvanized earth plate electrode 600 x 600 x6mm thick burried directly in ground vertically to a depth not less than 2.25 M below normal ground level with top edge of the plate not less than 1.50 M below normal ground level , connected to and including galvanized steel wire 4mm dia as earth lead soldered and riveted to earth plate by means of nuts, bolts, check nuts & washers of galvanized iron or steel with connected to test point and testing on completion including 15mm GI light grade pipe for earth lead protection from earth point to earth plate, including provn adequate quantity of charcoal dust mixed with 35 % common salt to a packed thickness of not less than 15 cm in alternate layers of charcoal and salt on all sides of earth plate with 20mm bore medium grade GI Pipe for watering,GI check nut, funnel and wire mesh with and including all necessary excavation & earth work in soft/loose soil, returning filling in, removal of surplus soil to a distance 50 metre,,PCC 1:3:6 type C-1 as in earth pit, 40 mm thick RCC cover using cement concrete 1:2:4 type B-1 reinforced with & including 8 mm dia mild steel TMT bar @ 100 mm c/c Both way with suitable handle for lifting arrangement & including form work complete all as specified and shown in electrical plate No 3 of MES SSR Part I 2009 and complete all as specified and directed. NOTES:- (i) On testing, after completion of Job, if desired earth resistance is not obtained, the earthing shall be redone at without any extra cost by contractor.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc as required 4 mm dia galvanized iron or steel wire complete all as specified and directed.

Excavation in trenches in soft / loose soil n.exc. 1.5 m wide and n.exc. 1.5 m depth for laying of cable, errection of poles, stay and pipe line and getting out complete all as specified and directed.

Returning and filling including spreading, leveling watering and wall ramming in layers n.exc. 25 cm thick in soft / loose of soil complete all as specified and directed.

Removal of excavated soil to a distance n.exc. 50 m above the starting point complete all as specified and directed.

S&F in repair of doule wall corrugated pipes as per IS 16025 part 24 of following sizes

(a) DWC pipe (6 mtr length) of 63 mm of outer dia and 50 mm inner dia with connecting accessories complete

(b) DWC pipe (6 mtr length) of 120 mm of outer dia and 102.5 mm inner with connecting accessories complete.

Supply, laying and testing in replacement cable XLPE insulated, screened, PVC bedded, galvanized steel stirp or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 240 sqmm 3.5 core complete all as specified and directed.

Supply, laying and testing in replacement cable XLPE insulated, screened, PVC bedded, galvanized steel stirp or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 150 sqmm 3.5 core complete all as specified and directed.

Supply and fixing cable tray of size 100 mm, 14 SWG with tray cover including all fittings for fixing on wall / truss complete all as specified and directed.

Supply, laying and testing in replacement cable XLPE insulated, screened, PVC bedded, galvanized steel stirp or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 50 sqmm 3.5 core complete all as specified and directed.

Demolition of PCC / Black bitumin road of any description and in any position not otherwise specially provided etc complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 using 20 mm graded stone aggregate for coping of poles, panel board etc complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x6mm thick burried directly in ground vertically to a depth not less than 3.25 M below normal ground level with top edge of earth plate at a depth not less than 2.50 M below normal ground level , earth plate surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using galvanized iron strip of 32 x 6 mm as earthing lead (pto the body of the equipment) by means of bolts, nut, check nuts, and washers made of galvanized iron and thimbles and protected by medium 40 mm dia GI pipe connected to main switch board or main control board of equipment nad GI pipe medium grade 20 mm bore for watering and including funnel, wire mesh, 40 mm thick RCC pit cover reinforced with 8 mm dia TMT bar at 75 c/c/\ both ways and lifting arrangement by providing handles (02 Nos) of 12 mm dia MS round bar and PCC chamber pit with PCC (1:3:6) type C-1 (using 20 mm graded stone aggregate) including excavation and earth work in soft / loose soil, returning, filling in with excavated soil and disposal of surplus soil to a distance not exceeding 50 m and shown in electrical plate No.3 of SSR-2009 (Part-I) complete all as specified and directed.

Supply, installation and testing and commissioning in replacement of feeder pillar box, kisok indoor type floor mounted factory fabricated weather and vermin proof protection class IP 43 made out of 2.0 mm thick, MS sheet CRCA sheet on angle iron 50 x 50 x 6 mm frame of size suitable to incorporate following accessories with front and rear opening doors, fully compartment wire, having seven tank treatment process with thickness not less than 60 microns with paint shade RAL 7035 provided with suitable gasket to make it dust / vermin proof, handle type locking arrangement powder coated internally and externally shall have channel base of approriate size and mounted on PCC foundation of size as required or approved by manufacturers in PCC 1:3:6 tpe C-2 using 40 mm graded crushed stone aggregate as recommended by manufacturer or directed by Engr in charge including taking down of old panel completion comprising of following :

INCOMING :- (a) Changeover capacity 400 Amp, 4 pole, 415 V, 36 KA, Ics=Icu=100% Thermal magnetic adjustable type - 1 No. (b) MCCB capacity 400 Amp, 4 pole, 415 V, 36 KA Ics=Icu=100% Thermal magnetic adjustable type - 1 No. (c) Busbar chamber comprising 4 Nos made of aluminium strip of capacity 600 Amps with PVC insulated & PVC sheathed with colour coding. (d) Multifunction digital panel meter with LCD display flush mounting type of size 96 x 96 mm, accuracy class, 1 suitable for CTs with secondary current 5A-01 No. (e) Indicator lamp LED based (RYB) - 01 No. OUTGOING : (a) MCCB capacity 160 amp, 4 pole, 415V, 25 KA Thermal magnetic adjustable type complete with spreader links - 03 Nos (b) MCCB cpacity 125 amp, 4 pole, 415 V, 16 KA Thermal magnetic adjustable type complete with spreader links - 01 No.All accessories pre-wired with suitable size PVC insulated copper conductor cables for control wiring and PVC insulated copper strips of appropriate size for circuits as per standard engineering practice and required at site.

Supply, installation and testing and commissioning in replacement of feeder pillar box, kisok indoor type floor mounted factory fabricated weather and vermin proof protection class IP 43 made out of 2.0 mm thick, MS sheet CRCA sheet on angle iron 50 x 50 x 6 mm frame of size suitable to incorporate following accessories with front and rear opening doors, fully compartment wire, having seven tank treatment process with thickness not less than 60 microns with paint shade RAL 7035 provided with suitable gasket to make it dust / vermin proof, handle type locking arrangement powder coated internally and externally shall have channel base of approriate size and mounted on PCC foundation of size as required or approved by manufacturers in PCC 1:3:6 tpe C-2 using 40 mm graded crushed stone aggregate as recommended by manufacturer or directed by Engr in charge including taking down of old panel completion comprising of following :

INCOMING :- (a) MCCB capacity 320 Amp, 4 pole, 415 V, 36 KA Ics=Icu=100% Thermal magnetic adjustable type - 1 No. (b) Busbar chamber comprising 4 Nos made of aluminium strip of capacity 500 Amps with PVC insulated & PVC sheathed with colour coding. (c) Multifunction digital panel meter with LCD display flush mounting type of size 96 x 96 mm, accuracy class, 1 suitable for CTs with secondary current 5A-01 No. (d) Indicator lamp LED based (RYB) - 01 No. OUTGOING : (a) MCCB capacity 160 amp, 4 pole, 415V, 25 KA Thermal magnetic adjustable type complete with spreader links - 02 Nos (b) MCCB cpacity 100 amp, 4 pole, 415 V, 16 KA Thermal magnetic adjustable type complete with spreader links - 02 No. All accessories pre-wired with suitable size PVC insulated copper conductor cables for control wiring and PVC insulated copper strips of appropriate size for circuits as per standard engineering practice and required at site.

M/s J S & SONS (BID ID -3329304)

Yohan Engineers and Contractors (BID ID -3338875)

Lachman Das Govind Ram (BID ID -3330589)

CREATIVE CONSTRUCTION (BID ID -3330216)

M/S DEVENDRA KUMAR GUPTA (BID ID -3331000)

Gupta Automobiles (BID ID -3330479)

garg construction company (BID ID -3330929)

R.C. Magla and Co. (BID ID -3330590)

M/s SCHOLASTIC ENTERPRISES (BID ID -3338749)