Mechanical Engineering

Description of Item

Static & Dynamic balancing Apparatus Drive Motor: FHP Motor, variable speed, with speed controller. Balancing weight: 4 Nos. of Stainless Steel with different sized eccentric mass for Varying unbalance. Rotating Shaft: Material Stainless Steel Supplied with Instruction Manual

Cam and Follower Apparatus Cam Shaft : Material Stainless Steel Cams: Tangent, Eccentric, Circular Arc, made of hardened alloy – steel. Followers: Roller, Knife edge, Mushroom, made of hardened alloy – steel. Compression Spring : Provided Weights : 1 kg., 500gm, 200 gm & 100gm Motor : Variable speed DC Motor with speed controller Dial Gauge : Baker & Mercer/Standard Make Supplied with Instruction Manual

Universal Vibration apparatus Exciter Unit : With FHP DC Motor with Speed Control Facility RPM measurement: Digital RPM Indicator with Proximity sensor. Ordinary Chart recorder: For recording Frequency and Amplitude of Vibration. Stop Watch: Electronic Stop Watch. Supplied with Instruction Manual

universal Governor Apparatus Watt governor,porter governor,proell governor and Hartnell governor Spindle : Material Stainless Steel Governor Mechanism Motor: Variable speed, Standard Make, FHP Motor. Control Panel: For speed control of motor. Supplied with Instruction Manual

Single cyliner multi fuel VCR engine with dynamometer testrig with smoke analyser COMPUTERIZED ENGINE TEST SET-UP FOR VARIABLE COMPRESSION RATIO MULTIFUEL ENGINE. ENGINE: Type - Single Cylinder, Four-Stroke, Spark / Compression Ignition Variable Compression Ratio Engine Alternative Fuel Development for S.I. & C.I. engines. MECHNISM –In this engine, the compression ratio is to be varied by a mechanism which involves Raising or lowering the total head assembly including the valves, camshaft etc. The linear movement of the head assembly should be measureable Precisely by a Depth micrometer / Plunger Dial and this reading can be used directly to calculate compression ratio directly by means of Graph & Table provided & also by inputting the value in the software IT SHOULD BE POSSIBLE TO VARY Compression Ratio continuously FROM 5 :1 TO 22:1 Without dismantling or changing the Cylinder Head Technical Specifications: - Bore X Stroke – Approximately 87.5 mm X 110 mm Rated Capacity – 6.5 B.H.P. @ 1500 RPM when using High Speed Diesel @ CR 17.5:1 or Better Compression Ratio Adjustable from – 5:1 to 11:1 FOR SPARK IGNITION MODE & 12:1 to 22:1 FOR COMPRESSION IGNITION MODE Water Cooled engine.Fuel Delivery: - Carburettor for SI Mode & Fuel Injection Pump for CI mode Ignition timing for SI Mode 50º BTDC to 10º ATDC Starting – Thro The Dynamometer Compression is to be adjustable even when the engine is running. The flywheel MUST BE calibrated in Degrees to allow accurate measurement of ignition timing, using stroboscopic light method. An adjustment is provided so that the ignition timing, can be adjusted while the engine is running. B. DYNAMOMETER – Air Cooled AC Regenerative Dynamometer with Load Cell type Weighing Mechanism & Max Torque above 60 N-m Accuracy is < 0.25 % of Full Scale Torque of Dyno. RPM indicator is supplied with the dynamometer. C. Common Base Frame: - The engine and dynamometer are mounted on a Common Rigid Channel Frame, which can be directly mounted on the foundation block D. Cardan Shaft: A Suitable Cardan Shaft for connecting Engine to Dynamometer is provided E. Cardan Shaft Guard for protection from rotating shaft

Hand Held Flue Gas Analyzer For measurement O2,CO, CO2 (cal.), NO, SO2, diff. pressure, Temperature and velocity measurement. With built-in printer and dataloger. Complete with 50cm or 100cm long sampling probe with 3 meter long sampling hose, filter assembly, battery charger, instruction manual datalogging software, carrying case and calibration certificate. with sensors Parameter Measuring range Oxygen : 0 to 21% CO : 0 to 8000 ppm NO : 0 to 5000 ppm SO2 : 0 to 5000 ppm CO2 : 0 to 99% calculated Temp. : 0 to 1250 oC Diff. pressure : ±200 mbar Velocity measurement : 0- 97 m/sec

Fuel supply system model The models displays the fuel supply system on board. All the components are shown separately on the board and connected with a line to show how it works

Cooling system model The models displays the the working and components used in the cooling of an automobile engines.

Ignition system model The models displays the the working and components used in the ignition system of an automobile

Lubrication system model The models displays the the working and components used in the lubricating system of an automobile engine.

Fuel pump model The models displays the the working and components of fuel pump used in IC engines

Fuel injector model The models displays the the working and components of fuel injector.

Different types of carburetor models : The models displays the the cut section of different carburetors: Single stage single barrel, two stage single barrel or two stage two barrel

Throttling and seperating calorimeter apparatus Separating Chamber :Compatible capacity made of Stainless Steel insulated with Ceramic wool with water level indicator. Throttling Chamber :Compatible capacity provided with gauge to measure in let Pressure before throttling Heat Exchanger : For Condensing steam after throttling chamber Steam Generator : Compatible capacity with digital temperature controller tocontrol the temperature inside the steam generator. Differential pressure : By manometer Measurement Steam pressure measurement: By Pressure gauge An ENGLISH instruction manual consisting of experimental procedures, block diagram etc.will be provided along with the Apparatus The whole set – up is well designed and arranged on a rigid structure painted with Paint.All the temperature should be displayed at one time on 2004 JUMBO GRAPHICAL DISPLAY with assistance of micro-controller.

Models of different types of steam condenser The models displays the the working and components of STEAM CONDENSER

Models of different types of steam nozzeles The models displays the the working and components of STEAM Nozzles. ( FIXED DIA, VARI=YING DIA etc.)

Determination of Cd,Cc and Cv Orifice and Mouthpiece Apparatus : Set of Orifices: Material Acrylic (2 Nos.) Dia. 10mm and 15 mm Set of Mouthpieces: Material Acrylic (3 Nos.) Dia 10 mm (L/D = 1) Dia 10 mm (L/D = 2.5) Dia 10 mm (L/D = 4) Constant Head tank: 35 Ltrs. Pointer Gauge: To measure X-Y co-ordinates of Jet. Water Circulation: FHP Pump, Crompton make. Flow Measurement: Using Measuring Tank with Piezometer, Capacity 25 Ltrs. FLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons. Sump Tank: Capacity 70 Ltrs. Stop Watch: Electronic. Control Panel Comprises of : Standard make On/Off Switch, Mains Indicator, etc. Supplied with Instruction Manual with the Apparatus Tanks will be made of Stainless Steel. The whole set-up is well designed and arranged in a good quality painted structure

Notch Tank Apparatus Channel Test Section: Size 600 x 250 x 180 mm. Notches : Material Brass Rectangular Notch 45° V Notch 60° V Notch Pointer Gauge : With Vernier scale. Water Circulation: FHP Pump Crompton makes. Flow Measurement: Using Measuring Tank with Piezometer, Capacity 25 Ltrs. FLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons. Sump Tank: Capacity 50 Ltrs. Stop Watch: Electronic. Control Panel Comprises of : Standard make On/Off Switch, Mains Indicator, etc. Supplied with Instruction Manual The whole set-up is well designed and arranged in a good quality painted structure

Jet on Vane Appartus Target (2 Nos.) : Flat Plate and Hemispherical Cup Nozzle : Material Brass Jet Enclosure : Made of Acrylic Water Circulation : FHP Pump, Standard make Flow Measurement: Using Measuring Tank with Piezometer, Capacity 25 Ltrs. FLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons. Sump Tank: Capacity 50 Ltrs. Stop watch: Electronic. Control Panel Comprises of :Standard make On/Off Switch, Mains Indicator, etc.Supplied with Instruction Manual Tanks will be made of Stainless Steel. The whole set-up is well designed and arranged in a good quality painted structure

Combined Pipe Friction Measurement Appartus Pipe Test Section: (i) Dia ½”, Length : 1m, Material G.I. (ii) Dia ¾”, Length: 1.25m, Material G.I. Water Circulation: FHP Pump, Crompton/godrej/G.E makes. Flow Measurement: Using Measuring Tank with Piezometer, Capacity 25 Ltrs. FLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons. Sump Tank: Capacity 50 Ltrs. Stop Watch: Electronic. Control Panel Comprises of : Standard make On/Off Switch, Mains Indicator, etc. Supplied with Instruction Manual with the Apparatus Tanks will be made of Stainless Steel. The whole set-up is well designed and arranged in a good quality painted structure

Venturimeter and Orificemeter Apparatus Venturimeter: Material Clear Acrylic compatible to 1” Dia. Pipe. Orifice meter : Orifice plate made of Stainless Steel and housing made of Clear Acrylic compatible to 1” Dia. Pipe. Pitot tube set up made of stainless steel/Copper of compatible size fitted with vernier scale and housing made of clear Acrylic section compatible to 1” dia. Pipe. Water Circulation: FHP Pump, Crompton make. Flow Measurement: Using Measuring Tank with Piezometer (Capacity 25 Ltrs.) and Electronic Stop Watch FLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons. Sump Tank: Capacity 50 Ltrs. Control Panel Comprises of: Standard make On/Off Switch, Mains Indicator, etc. Supplied with Instruction Manual, Tanks will be made of Stainless Steel. The whole set-up is well designed and arranged in a good quality painted structure

Bernoullis Apparatus Test Section: Material Acrylic (One Piece). Piezometer Tubes: Material P.U. Tubes (7 Nos.) Water Circulation: FHP Pump, Crompton make. Flow Measurement: Using Measuring Tank with Piezometer, Capacity 25 Ltrs. FLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons. Sump Tank: Capacity 70 Ltrs. Inlet Tank: Capacity 20 Ltrs. Stop Watch: Electronic. Control Panel Comprises of: Standard make On/Off Switch, Mains Indicator, etc. Tanks will be made of Stainless Steel. Supplied with Instruction Manual The whole set-up is well designed and arranged in a good quality painted structure

Metacentric Height Apparatus Pontoon: Size 300 x 300 mm (approx.) with a Horizontal Guide Bar for aliding weight and Removable Strips, Graduated Arc with Pointer with moveable hanger and set of weights. Water Tank : Size 550 x 500x 400 mm (approx.) Front Window of Tank : Made of Glass/Perspex. A set of weights is supplied with the apparatus. Supplied with Instruction Manual Tanks will be made of Stainless Steel. The whole set-up is well designed and arranged in a good quality painted structure

Models of different pipe joints The models displays the various type of pipe joints used in the pipelines

Models of different types of water pumps The models displays the various type of Pumps used in water flow system. It could be centrifugal pump, magnetic pump, peristaltic pump etc

Pelton wheel turbine Test Rig Output Power: 1 kW. Discharge: 400 LPM (Approx.) Supply Head: 25 m Speed: 1000 RPM (Approx.) Nozzle: Material Stainless Steel. Spear: Material Stainless Steel. Dynamometer: Rope Brake type. Sump Tank: Capacity 200 Ltrs. Water Circulation: Centrifugal Pump, Standard make, Capacity 5 HP, Three Phase, 2800 RPM Discharge Measurement: Pitot tube with Manometer All pressure and RPM value should be displayed on 2004 JUMBO Graphical Display with assistance of microcontroller. Tanks will be made of Stainless Steel. The whole set-up is well designed and arranged in a good quality painted structure

Models of Piezometer and different types of monometer The models displays the various type of Manometer that can be put into the use for the measurement of pressure change

Pitot tube apparatus to determine discharge Pitot tube: Material Copper/SS of compatible size fitted with vernies scale. Test Section: Material Clear Acrylic, compatible to 1” Dia. Pipe. Water Circulation: FHP Pump, Crompton make. Flow Measurement: Using Measuring Tank with Piezometer (Capacity 25 Ltrs.) and Electronic Stop Watch FLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons. Sump Tank: Capacity 50 Ltrs. Control Panel Comprises of : Standard make On/Off Switch, Mains Indicator, etc. Supplied with Instruction Manual Tanks will be made of Stainless Steel. The whole set-up is well designed and arranged in a good quality painted structure

Hydraullic Test Bench Top Tray : Size 1000 x700 x 100mm(approx) Water Circulation : 1 HP Pump, Crompton/Kirlo skar make. Flow Measurement : Using Measuring Tank, Capacity 40Ltrs. FLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons Sump Tank : Capacity100Ltrs. StopWatch : Electronic. Control Panel Comprises of : Standard make On/Off Switch, Mains Indicator, etc. Tanks and Top Tray will be made of Stainless Steel. Supplied with Instruction Manual The whole set-up is well designed and arranged on a rigid structure painted with Paint

Kaplan turbine Test Rig Output Power : 1 kW. Discharge : 1000 LPM Supply Head : 5-8 M Normal Speed : 2000 RPM Dynamometer : Rope Brake type. Water Circulation : Centrifugal Pump, CRI/Standard Make, Capacity 5 HP, 3 Phase. Discharge Measurement : Pitot Tube with Manometer All pressure and RPM value should be displayed on 2004 JUMBO Graphical Display with assistance of microcontroller Sump Tank : Capacity 200 Ltrs. Pressure Measurement : Pressure Gauge & Vacuum Gauge Piping & Fittings : Pipes & fittings with flow control valves of suitable size Tanks will be made of Stainless Steel. The whole set-up is well designed and arranged in a good quality painted structure

Francis Turbine Test Rig Output Power : 1 KW Discharge : 1000 LPM (Approx.) Supply Head : 10 m (Approx.) Speed : 1000 RPM (Approx.) Runner: Having Curved Vanes. Dynamometer: Rope Brake type. Sump Tank: Capacity 200 Ltrs. Water Circulation: Centrifugal Pump, Standard Make, Capacity 5 HP Three Phase. Discharge Measurement : Pitot Tube with Manometer All pressure and RPM value should be displayed on 2004 JUMBO Graphical Display with assistance of microcontroller Control Panel Comprises of : L&T make Starter, Mains Indicator, MCB for overload protection. Supplied with Instruction Manual Tanks will be made of Stainless Steel. The whole set-up is well designed and arranged in a good quality painted structure

Link polygon apparatus The apparatus is provided with five linkages and connectors, having hooks to which pans are hung.These are fixed between two pulleys around which rope is run to connect to two extension type spring balances. The unit is very useful for the study of arches, abutments and piers. The wooden rectangular beam is fitted with scale.With weights.

Simple wheel and axle The wheel and axle is a machine consisting of a wheel attached to a smaller axle so that these two parts rotate together in which a force is transferred from one to the other. A hinge or bearing supports the axle, allowing rotation. It can amplify force; a small force applied to the periphery of the large wheel can move a larger load attached to the axle

Screw efficiency apparatus A jackscrew, or screw jack, is a type of jack that is operated by turning a leadscrew. It is commonly used to lift moderately heavy weights, such as vehicles; to raise and lower the horizontal stabilizers of aircraft; and as adjustable supports for heavy loads, such as the foundations of houses

Automotive Lighting This apparatus displays the arrangement of lighting system used in automobiles. All the required accessories are displayed on the panel board for study

Automotive Electrical Circuit The demonstration board which will give a complete idea of the electrical system of maruti car. In this demonstration board the actual wiring with the parts and accessories of a car had been arranged, according to the electrical circuit of the car and terminals are connected to the battery .

Automotive Electronic circuit Electronic ignition system is a working model designed to demonstrate the students operation of a typical electronic system used in the car. The trainer consists of ignition coil, distributor, set of spark plugs and 12 V DC supply.

Vehicle Displays Principles systems Trainer This trainer is designed to teach students principles of Vehicle Display System and warning systems through comprehensive practical activities. The activities include instrument cluster, fuel system warning system, engine sensor warning system, automotive lighting instrumentation, passenger safety warning system, ABS failure warning system and engine failure warning system

Ignition and charging system This apparatus displays the spark plug used for ignition and the related accessories. Also the Charging system is also explained in the model

Digital Multimeter 3 ¾ Digit, 3100 Counts, Auto Power Off, Auto / Manual Ranging, Continuity, Diode Check, Warning for Blown Fuse & Overload Condition, Automatic Terminal Blocking System, Min / Max Value Storage, Data Hold, Digital cum Analog Bar graph Indication, Bat low Indication AC Voltage: 30 mV – 1000 V, DC Voltage: 3 V – 1000 V, AC Current: 300 uA – 10 A, DC Current: 3 mA – 10 A, Resistance: 30 Ohm – 30 MOhm, Capacitance: 30 nF – 30 uF, Frequency: 300 Hz – 100 kHz, Temperature: -200 to +850 Deg C (Pt 100/ Pt1000 input) Basic Accuracy: 0.1 %/ 0.25 % Operable with 9 V battery Holster of Soft Rubber for shock & drop protection, Electromagnetic Compatibility ( EMC ), IP 50 & IP 20 Protections, Supplied with set of lead, user manual, test & Calibration certificate, Rubber Holster, Carrying belt, ,

Tungsten Inert Gas Welding Machine(TIG). voltage 415 volt,frequency 50Hz,range output:5-35 Amp,DC max 74 volt,Adjustable clean ratio for perfect perfect aluminium welding,spot welding digital display,5 different ac waveform output synchronous mutual arc feature optimal water cooled,water cooling machine.1 power source,product type AC/DC with electrode holder,pulse TIG.,TIG torch,input current 20 Amp & output current 315 amp,cable length 3 metre.

CNC turning trainer machine Swing over bed: more than 110 mm Swing over carriage: more than 60 mm Distance between centers: more than 420 mm Hole through spindle: 10 mm Spindle nose thread: 3/4"-16 T.P.I . Spindle nose taper: #1 Morse Travel of crosslide: more than 100 mm Taper of tailstock spindle: #0 Morse. Protractor graduations: 0° to 45° by 5° Handwheel graduations: .0.01 mm Motor: 90 Volt DC with electronic speed control, input 220V/50Hz. Spindle speed range: 70-2800 RPM continuously variable by electronic eed control CNC stepper motor holding torque: 136 oz-in Rapid travel speed, X and Z: 22 inches/min The system enclosed in a metallic enclosure , openable front door, acrylic front and side cover and display panel. Having coolant system with removable collector. System Having mechanical storage system on the bottom for Computer system, Controller and for Electrical wiring. The system shall be supplied withPC, Optical Mouse, 17” TFT Monitor & Keyboard.

Impact Testing Machine. Pendulum drop Angle:(140 degree for Charpy test)& (90 degree for Izod test),Pendulum Impact energy:300J (Charpy test) & 168J for Izod test,striking velocity of pendulum:2.45m/sec. for charpy test & 3.857 m/sec. for Izod test.,Scale graduation:2J,Max. permissible less by friction :0.50% of Impact energy.

Radial Drilling Machine. Heavy Duty, Radial Drilling Machine - 25mm Cap / 8 Speed / 200mm Travel with FINE FEED Attachment Column, arm, work head & gears made out of closed grain, spindle ram is made out of alloy steel & main spindle & pinon are made of EN forged steel drilling capacity : 25 mm, column dia : 127 mm, Spindle nose : MT-3, Spindle travel : 200 mm, speed : 110-2880 RPM, Ram dia : 72 mm, drilling radius : 660 mm, drillling head motor : 1 hp (1440 rpm), lifting of arm motor : 0.5 HP, Dist. from spindle to base : 810/130, Dist. from column to spindle : 620/350, supplied with Electrical such as 1 HP 1440 RPM 3 phase Ele. Motor for Drilling 0.5 HP 1440 RPM 3 phase Ele. Motor for Lifting R/F switch 2 Nos. V-Belt 2 Nos. with Fitting… : 1 No. Box Table [250x205x205mm] , ½” Drill Chuck , ½” Arbour , 2/3” Sleeve , 6” Drill Vice

Impact Testing Machine. Impact Testing M/C (Charpy/Izod) Works on pendulum principle, Difference between heights of drop of pendulum before Rupture & Height of rise after Rupture of specimen is directly proportional to impact energy absorbed. Direct indication of impact energy absorbed by specimen on large dial. Confirms to BS 131 part IV-1972 & BSEN 10045-2:1993 Max. capacity: 300 Joule Min. scale graduation: 2 Joule

Metal Arc Welding Machine Three phase,380 V,IGBT technology based,cooling mode: Air cooled,output current:300-400 A,invertor based,stainless steel material,Galvanised surface.

Hydraulic Power Hacksaw Perfectly toothed to cut metal sheets,Continous hydraulic system for facilating and lifting operation,optimal floor space.No. of stroke per minute:80,Electric motor:1 HP,Capacity of round bar:8'',Capacity of square bar:6''Blade size:16*1.25",Stroke:5.75"size:8"

Universal Testing Machine.(40 /100 tonnes) Capacity: 400/1000 KN Mechanical Model Loading accuracy as high as ±1%. Training roll autographic recorder supplied as standard to enable study of the behavior of materials, High reading accuracy due to large size and design of dial.Wide range of standard and special accessories, including load stabilizer. Easy change from plain to threaded and screwed specimens. Motorised loading and unloading cycle. Large effective clearance between columns enables testing of standard specimens as well as structures. Simple controls for ease of operation. Safe operation ensured by means of safety devices. Fully enclosed and protected pendulum.

Universal Testing Machine.(100 tonnes) Capacity: 1000 KN Mechanical Model Loading accuracy as high as ±1%. Training roll autographic recorder supplied as standard to enable study of the behavior of materials, High reading accuracy due to large size and design of dial.Wide range of standard and special accessories, including load stabilizer. Easy change from plain to threaded and screwed specimens. Motorised loading and unloading cycle. Large effective clearance between columns enables testing of standard specimens as well as structures. Simple controls for ease of operation. Safe operation ensured by means of safety devices. Fully enclosed and protected pendulum.

Multi Cylinder Four Stroke Water Cooled Diesel Engine Test Rig Four cylinder, four stroke engine, vertical water cooled, self start, diesel engine. Eddy Current Dynamometer The engine coupled with Eddy Current Dynamometer with resistance loading arrangement. Digital voltmeter ,digital ammeter are provided.Digital techometer also provided. weighing gear, control gear, a dead weight in Kg unit suitable for testing the engine at different speeds. The engine and dynamometer are directly coupled on a substantial base plate. Fuel measuring system of a fuel tank, a burette and a three way cock arrangement. Air tank with orifice and water manometer. Measurement of Heat carried Inlet outlet piping with flow control valve, water away by Cooling water meter. Thermometers are provided to measure the inlet outlet temperature of water. Common Base Frame: - The engine and dynamometer are mounted on a Common Rigid Channel Frame, which can be directly mounted on the foundation block .

CNC milling trainer machine Stepping Resolution: 0.003mm Mechanical repeatability : 0.01mm Spindle Speed : 1100 - 11000 RPM Travel: X = 300mm, Y = 146mm, Z = 153mm Rapid Travel of 30 in/min. Universal Standard G-Code import. Plugs directly into computer printer port. Precision Mechanics. Box way Z-axis assembly with ground steel plate and tapered brass gib. Adjustable tapered brass gib on X-axis. Ground steel sliding ways with adjustable brass gib. Hard anodized aluminum table. 1/2" (12.7mm) 20 pitch Cr-Mo lead dscrews with adjustable split bronze nuts on all axes. The system should be installed in a metallic enclosure with at least 5' height, openable front door, acrylic front and side cover and display panel.Having coolant system with removable collector. System having mechanical storage system on the bottom for Computer system, Controller and for Electrical wiring. The system supplied with PC Optical Mouse, 17” TFT Monitor & Keyboard. The complete system included with: MicroMill with Powerful 1/4 HP spindle motor, Pulley set with drive belt, 1/8" (3mm) or 3/16" (4mm) or 1/4" (6mm) collet with collet closer, Electronic Chopper Driver Unit, Custom Win 7 Mach 3 control software interface, 4th Axis Amplifier and Port Included, Input/Output Port Included, 200 oz-in. stepping motors, Printer cable, power cable etc.

Heat pump Apparatus Compressor: Hermitically sealed compressor. Capacity 1/3 Ton, Condenser: Water cooled type shell and coil condenser with refrigerant inside the tube. Water flow measurement: Provided with individual rota meters and four temperature Sensor for both condenser and evaporator. Expansion Valve: Capillary Tube, Compatible Capacity. Safety Control: Overload and over current protectors for compressor and Time Delay circuit. Evaporator: Water cooled Compatible capacity. Temperature Sensor: RTD PT-100 Type. Control Panel comprises of: Digital Voltmeter: 0-300 V Digital Ammeter: 0-5 Amp. Temperature Measurement: Digital Temperature Indicator with multi-channel switch.Supplied with Instruction Manual All the accessories will be mounted on a rigid base frame made of M.S. and it will be powder coated.  All the temperature should be displayed at one time on 2004 JUMBO GRAPHICAL DISPLAY with assistance of micro-controller

Rockwell cum Brinell Hardness Testing Machine (Digital) (Hardness tester for Metal like steel, copper, brass, aluminum etc) (Readings on Digital screen in HRC or HRB Scale—For Rockwell Test ) (For Brinell Test -Manually measure the indentation diameter by using Brinell Microscope and Brinell hardness table). Major Loads :-Rockwell Loads :60,100,150 kgf Brinell Load : 187.5 , 250 kgf Minor load for Rockwell : 10 kgf Indentor : Diamond and 1/16’’ ball indentor For Rockwell test and 2.5 and 5 mm Ball Indentor for Brinell Test Maximum test height : 230 mm Depth of throat : 133 mm 50MM Flat table and 35mm vee groove table HRC /HRB/ HBW Test block---1 no Each According to IS:1586:2000

ROBOTIC ARM TRAINER WITH PC INTERFACE The robotic arm interface kit connects Robotic Arm Trainer to a personal computer,.The software for the interface permits real time control and contains a built-in interactive script writer. A user may write a script that contains up to 99 individual robotic arm functions (including pauses) into a single script file. Script files may be saved and loaded from disk just like any other standard computer file. Script files may be replayed automatically up to 99 times for demonstrating computer controlled automation and animatronics. The Robotic Arm PC Interface provide learning and experimenting with computer automation and animatronics.

Lathe Machine. 5.5 Feet bed length High Precision Medium Duty Double V-Belt Drive Lathe Machine complete with all standards Accessories such as Chuck Plate, Gear Set, Center Adaptor, Dead Center, Dial Indicator, Square Tool Post, Tool Post Key with HARDENED BED Length of Bed : 5 ¼ ' , Height of Centre : 212 mm, Width of Bed. : 280 mm, Spindle Hollow : 52 mm, Admit Between Centers. : 725 mm Extra accessories: Electrical such as 2 HP 1440 RPM 3 Phase Electric Motor, Switch, V-Belt & Fittings, 8” x 3 Jaw Precision True Chuck with chuck plate, 12’ x 4 Jaw Dog Chuck with chuck plate, Face Plate , Follow Rest, Steady Rest

Power pipe cutter CUT OFF MACHINE 14” CUT – OFF Machine with 2 HP. 3 Phase Electric Motor, V - Belt, Fitting with Abrasive Wheel – 1 No.

Hand grinder Wheel Diameter (inch) 1"/ 25mm Collet Chuck Size (mm) 6 mm Power Consumption (Watt) 520 W No Load Speed (rpm) 23000 to 30000 Spindle Size 5/32"- 14

Pedestral Grinding Machine 1 HP 3 Phase 2800 RPM PEDESTAL GRINDER with Grinding Wheels Size 10” x 1", 2 No. Wheel (one fine & one coarse) at each end, fitted with wheel guard, tool rest & cast iron leg

Shaper Machine. 18'' Heavy Duty ALL GEARED Type SHAPING MACHINE Machine Size: 18", Maximum Stroke: 20", Len of Ram: 36" Max. dist. of Table to Ram: 15" Min. dist. of table to Ram: 2" Max. vertical travel to tool slide: 4" Length & width of table top.: 18" x 12" Length & width of table slide: 30" x 11" Length of cross slide: 30" Width of Ram: 10" No of speeds: 3 Main Motor Power: 2 HP, Fitted with Vice, Motor Pulley, Handle, Ram Back Tray & Automatic Lubrication Arrangement , Accessories : Electrical such as 2 HP 3 Phase 960 RPM Electric Motor, Starter, V-Belt & Fittings, Key way cutting attachment

Forge Furnance Maximum Temp.950°C, work on 220/230 v or 440 V AC, 3 phase supply

Carpentry shop Carpentry Vices

Rules

Straight edge

Try square

Mitre square

Bevel square

Combination square

Marking Knife

Mortise Gauge

Cutting gauge

Wing compass

Trammel

Divider

Calliper

Spirit level

Plumb bob

Rip saw

Cross-cut saw

Panel saw

Tenon or back saw

Dovetail saw

Bow saw

Coping saw

Compass saw

Pad or keyhole saw

Firmer chisel

beveled edge chisel

Paring chisel

Morise chisel

gouges chisel

Jack Plane

trying Plane

Smoothing plane

Rebate plane

Plough plane

Spokeshave

Metal jack plane

Router

Gilmet

Bradawl

Ratchet Brace

Wheel Brace

Drill bit

twist bit

Expansion bit

Centre bit

Forstner bit

Countersink bit

Warrington Hammer

Claw Hammmer

Ball pin Hammer

Straight hammer

Mallet

Bench hold fast

Sash cramp

G-cramp

Hand screw

Rasps

files

Scraper

Oil stone

Glass paper

Pincer

Cabinet Screw driver

Ratchet screw driver

Woodworking Lathe machine Operated with 1 HP motor & mounted on table top

Sheet Metal Shop Different snips

shears

stacks

latter

figure pucnh

solid pucnh

hollow pucnh

soft hammer

channel

square bars

standard sheet gauges

Mallet

Smithy shop Anvil

Swage block

Hand hammer

Ball peen hammer

Straigt peen hammer

cross pin Hammer

Flat tongs

Rivet or ring tongs

Straight-lip fluted tong

Gad tongs

Flat tongs

Flatter

fuller

Rivet header

Punch

Hot chisel

size plate or bush

cupping tool

different types and different size of dice and taps

Fitting Shop Fitting bench vice

leg vice

pipe vice

hand vice

pin wice

tool makers vice

hand hammer

ball peen hammer

cross peen hammer

straight peen hammer

soft hammer

flat chisel

cross cut chisel

half round chisel

diamond point chisel

side chisel

flat file

hand file

square file

pillar file

round file

triangular file

half round file

knife edge file

flat single cut and double cut file

triangulargle cut and double cut file

half round file

care off scraper

surface plate

scriber

punch,

v block angle plate

try square

hand reamer

machine reamer,

expanding reamer

Different sizes Hacksaw

Welding Shop Apron

Hand gloves

safety goggles

shoes

welding torch

pressure regulator

spark lighter

electrode for gas welding

electrode holder

cable lung

chipping hammer

earthing clamps

wire brush

Helmet

Sleeves

Arc Welding Machine with Trasformer,cables,Electrode holder,cables,connecter etc.

Gas Welding Machine.(oxyacctylene) with oxygen and acetelene cylinder ,pipes,welding torch etc.

Plastic moulding shop Bench moulding machine