Development of Interior works for INCENT LGD at IIT-M Research park

Amount

CIVIL WORKS :

200MM THICK HOLLOW TERRACOTA BLOCKS

Providing and laying Block work 400X200X200 with adhesive mixed as per Manufacturer specification with waterproofing compound Dr.Fixit or equivalent approved by architects in superstructure at all heights The rate to be quoted will include cost of scaffolding and to include all tools and plants, materials all required for first quality work and all external wall surface to be exposed and to be finished as directed by the architect.

150MM THICK HOLLOW TERRACOTA BLOCKS

Providing and laying Block work 400X150X200 with adhesive mixed as per Manufacturer specification with waterproofing compound Dr.Fixit or equivalent approved by architects in superstructure at all heights The rate to be quoted will include cost of scaffolding and to include all tools and plants, materials all required for first quality work and all external wall surface to be exposed and to be finished as directed by the architect.

SCREED CONCRETE

Providing and laying in position cement concrete of specified grade including the cost of shuttering-at all floors. The ratio of CM 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 6mm size blue metal – upto varying thickness 40mm to 75mm. All areas to be finished with same level as per Engineer-in-Charge.

WALL PLASTERING

Prepare surface and plaster the inner surfaces of walls, R.C.C surfaces contiguous to masonry with cement mortar 1 : 4, 12mm thick using good river sand, including patch plaster etc. The rate to include apart from the above the cost of scaffolding, curing, tools and plants etc. Complete. - At all levels

AAC BLOCKS 200 MM THICK

AUTOCLAVED AERATED CONCRETE BLOCKS - Providing and laying autoclaved aerated cement blocks masonry with 200 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 sand ).

AAC BLOCKS 150MM THICK

AUTOCLAVED AERATED CONCRETE BLOCKS - Providing and laying autoclaved aerated cement blocks masonry with 150 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work

BRICK TILE CLADDING

Supplying & Laying of 230x75x20mm using Suitable adhesive .The rate to include apart from the above the cost of scaffolding, curing, tools and plants etc. Complete. - At all levels

INTERIOR WORKS

PARTITIONS / PANELING WORKS

SOLID PARTITION

Providing and fixing rigidly in position a partition using 50 x 50mm x 1.5mm Aluminium framework running both horizontally and vertically at not more than 600mm c/c both ways. The framework alternative vertical member to touch the true ceiling height from the finished floor level and fixed rigidly to the ceiling, flooring, walls or partitions. All vertical framework members shall be of a single piece without any joint as directed by the Architects The framework to be concealed with 12 mm thick MDF Board. The MDF Board will be camouflaged with 1.0mm thick laminate of approved colour and make and shade and make and grooves to be provided as shown in the drawing. MDF to Extend 100mm above the False ceiling Level. Measurement for Billing will be taken from FFL to bottom of False Ceiling Level. The rate quoted to include grouting and fixing and making up the flooring to its original condition as well as making provisions for laying conduits, switch boxes and light fittings etc. Basic Cost of Laminate : Rs. 750 /- Sqm.

SINGLE GLAZED TOUGHENED GLASS PARTITIONS

Supply and Fixing of Slim Glass partition of 10mm Toughened Glass using DORMAKABA Alterra Lite System-45 Frames OR EQUIVALENT to a height of maximum 3m or as per drawing. The Fixed glass to be fixed using DORMAKABA Alterra Lite BP45 OR EQUIVALENT Profiles at Top & Bottom & Alterra Lite SP45 OR EQUIVALENT at sides. The profile size to be 45x25MM to be fixed on to the floor/wall/ ceiling as per the architect design. DORMAKABA Alterra Lite H Junction OR EQUIVALENT profile to be used at all Glass to Glass vertical joints, 90 Deg L Junction Profiles and T Junction profiles necessary as per design. In case of Glass overall panel Alterra Lite MP45 & BP45 Overpanel OR EQUIVALENT Profile to be used. In case of Open glass edges EP45 OR EQUIVALENT End Profile to be used. The Alterra Lite profiles shall be suitable for Glass thickness of 10/12/13.52mm.The Profile shall be matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 2 mm Gauge thickness Excluding 20 Micron of Anodizing. The glazing will be taped with 3M Scotchcal 7725SE-324 Frosted crystal film OR EQUIVALENT the details shown in the relevant drawings. The Frosted crystal film is to be supplied to the correct size and shape as indicated in the relevant drawing and the film is to be precut digitally with a plotter, brought to site and pasted over the glass. Any additional details required for shaping the film is to be obtained from the Architects in advance before precut the film. Measurement for Billing will be taken from FFL to bottom of False Ceiling Level.

CLEAN ROOM GLASS PARTITION

Supplying & Fixing of Progressive type Double Glazed Clean Room Partition with 5mm thk toughened Glass and Frame in Powder Coated Finish on G.I Sheet and necessary arrangements as per manufacture specifications for clean room applications. Measurement for Billing will be taken from FFL to bottom of False Ceiling Level.

COLUMN PANELLING

Providing and fixing in position of the column panelling in a rectangular shape, circumscribing the R.C.C. Column with 50 x 50mm x 1.5mm aluminium framework as per the pattern shown in the drawing and embedded in the RCC Column. The framework is concealed with 12mm thick MDF board and camouflaged with 1.0mm thick laminate of approved shade and brand and grooves. The size and shape of the panelling as per the drawing given.The top and bottom portion of the column panelling abutting the false ceiling and flooring. The concealed faces of the MDF board is to be treated against borer / termite / deterioration and painted with one coat of primer and two coats of paint. The work is to be carried out in a first class workmanship manner all as per details shown in the drawing and as directed at site etc., complete. The rate quoted to include all the above apart from all leads lifts, transport and scaffolding etc. complete and as directed by the Engineer at site. The work is to be carried out in a first class workmanship manner all as per details shown in the drawing and as directed at site etc., complete. Basic Cost of Laminate : Rs. 750 /- Sqm

WALL PANELING

Providing and fixing of laminate paneling in walls as per the following:The Aluminium frame work comprising 50x25x1.5mm frame work at 600mm c/c in both ways on the wall(after drilling with pneumatic driller)at required locations.12mm thick MDF board is fixed to the framework as specified above and the MDF is camouflaged with 1.0 mm thick laminate of approved shade and all as per the drawing. The rate quoted to include all the above apart from all leads lifts,transport and scaffolding etc.,completed and as per directed by the Engineer at site. The work is to be carried out in a first class workman ship manner all as per details shown in the drawing and as directed at site etc., Measurement for Billing will be taken from FFL to bottom of False Ceiling Level. Basic Cost of Laminate : Rs. 750 /- Sqm

CLEAN ROOM PARTITION & PANELING

Supplying & Fixing of Progressive type Double skin modular 75mm thick Solid wall panel for partitions and wall paneling, made of 0.5 mm thick Powder coated sheets on both sides with PUF as infill of density 40 ± 2 kg /m3, GI Profiles for reinforcement along the periphery with bottom track, and necessary arrangements, All Joints shall be sealed with cleanroom compatible Neutral Grade Silicon Sealant. Measurement for Billing will be taken from FFL to bottom of False Ceiling Level

ACOUSTIC WALL PANELING

ACOUSTIC INSULATION IN SOLID PARTITIONS

Acoustic Insulation Using Anutone Synth PF or Equivalent having thickness 50mm, width 600mm, density 1000gsm filled between the aluminium framework and held in position by using chicken wire mesh/cross bracings/pasting on one side of the boards. Measurement for Billing will be taken from FFL to bottom of False Ceiling Level

VITRIFIED TILE WALL DADO (Above Counter Slab)

Providing and fixing Ist quality Vitrified glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make fixing using Approved Tile Adhesive , in all colours, shades as approved by Architect. (The tile to be pasted on MDF partition wall) Basic Cost of Tile Rs 700/-Sqm

LACQUERED GLASS SOLID PARTITION/ WALL PANELLING

Lacquered Glass - Directly fixed over Solid partition. Providing & fixing Wall Panelling as per Drawings, in general, with 6mmthick lacquered glass of approved make and shade as per pattern and details given in drawing directly over the MDF partition. The lacquered glass shall be fixed using 3M or Equivalent double-sided tape / clear neutral Silicone sealant /SS Stud as per architectural drawing. The edges shall be chamfered so as to get 'V'-Groove with the adjoining glass panel. The panelling with the required cut-outs for the electrical switchplates and LCD TV, etc all complete as directed and to the satisfaction of the Architect / Client. Rate to include all wastages, hardware, necessary supports & backing to ensure rigidity, levels & plumb, etc complete. Basic Cost of Lacquered Glass Rs . 1200/Sqm

INTERIOR EMULSION PAINT

Preparing the surface and applying POP Punning using Birla Putty or equivalent make approved by Architect Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour Two coats including primer 1 coat .

MELAMINE POLISH

Sand papering the surface with specified quality sand paper, applying 2 coats of sealer and applying 3 coats of glossy / matt finish melamine polish in required shade by spray for new work including rubbing with wax to desired finish.

VENEER FINISH

CARPENTRY PROVIDING AND FIXING VENEER . Providing and fixing 4mm thick veneer of approved make including making grooves as per the design, necessary hardware, adhesives etc. complete. Basic Cost of Veneer sheet Rs. 1000 per Sqm

LAMINATE FINISH

CARPENTRY LAMINATE Providing and fixing laminate of approved make, colour and pattern as directed using approved adhesive. Item includes surface preparation by scrapping and removing existing paint, if any. 1.0 mm thickness. Basic Cost of Laminate Rs. 750 per Sqm

WALL PAPER

Providing and fixing wall paper of approved make, shade, texture as directed. 100% washable, scratch resistance, peel proof, and fire retardant properties fixed with adhesive as per manufacturers specification. The wall paper should give a seamless finish. Basic Cost of wallpaper Rs.1000 per Sqm.

FLOORING

VITRIFIED TILE FLOORING

Providing and laying Glazed Vitrified floor tiles in different sizes (Minimum thickness of tile 10mm) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 sand), including grouting the joints with white cement and matching pigments etc., complete with spacer of 5mm. Supply and lay one coat of First quality POP layer over plastic sheet. for protecting the tiles from scratches and oil stains etc complete as directed. And same removing before handing over the work. Basic Cost of Tile Rs.1200 per sqm

LAMINATED WOODEN FLOORING

Providing and fixing of minimum 8mm thick Laminated wooden flooring, with surface finish with class AC4 (average 4550 cycles), impact resistance of 9N ,resistance to cigarette burn with a rating of 4(EN 438-2:05), swelling after 24 hrs in water of 8.22%, Modulus of rupture of 53.3 Newton/mm2, Internal bond 1.78 newton/mm2, surface soundness 2.0 newton/mm2(EN 13329:2000) with a 0.2 mm thick wear layer on top of a High Density Fiber-substrate core (density ~ 948.3 Kgs/M3) of plank size 1214 mm X 141.5 mm having locking arrangement (lock strength > 670 lbs/ft) with an underlayment made of natural colour foam , with accessories like End profile, Transition profile etc. complete. It is important to ensure the sub floor on which the laminate is being laid is smooth, flat & hard & free from moisture, grease, etc. In case of uneven sub floor the same should be leveled by self leveling compound. The moisture level present in the sub floor should be less than 8% before installation of the floor. The laminate shall have Armalock locking system. It is recommended to use a water barrier of minimum of 250 microns and 2mm polyethylene foam under the planks. The installation shall be undertaken as per the manufacturers installation instructions. The work should be carried out as per patterns / design all as shown in the relevant drawings. The rate to include the cost of all leads, lifts, wastages, tools and plants, design pattern etc complete as directed by the Architects. Basic cost of Laminated wooden Floor -Rs 1200 per sqm

PATTERNED POLISHED GRANITE FLOORING

Providing and laying 20mm thick polished Granite slab as per architectural design over cement mortar 1:4 using one part of cement and four parts of sand, joints are mitrated, the quality of stoned should be approved by the engineer in charge of the work. The rate to include the cost of all leads, lifts, wastages, tools and plants, curing, transport, taxes necessary bull nosing, 3M anti-skid tape for steps, grooves etc complete as directed by the engineer-in-charge. Basic Cost of Granite Rs .1800 per sqm

GRANITE COUNTER TOP

GRANITE WORK FIXING Mirror polished, 18 mm Providing and fixing 18 mm thick gang saw cut mirror polished (pre-moulded and pre polished);machine cut for dry pantry counter and similar locations of required size of approved shade; colour and texture laid using suitable Tile adhesive including moulding and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any color and shade, upto 0.5 sqm. Job to be done as per specifications and directions of site engineer. Basic Cost of Granite Rs .1800 per sqm

FOR WET LAB COUNTER

- Providing and fixing of Custom Built lab table 600mm width and 760mm Height of varying Length as per the site requirements. Unit to be made of 18mm thick MDF board for all vertical and horizontal members inclusive of the openable shutters except the rear vertical surface which is of 6mm thickness. All exposed MDF board surfaces to be finished in 1.0mm thk Laminate of approved colour and shade. Rear external surfaces of unit to be finished in 1.0mm thk Laminate so as the internal surfaces of the storage unit. All inside faces are to be finished with 0.8mm thk Laminate . All exposed MDF board edges to be finished with PVC edge banding. Unit to have necessary locking arrangements (efficient gadgets or equivalent) handles, hardwares, tower bolt, hinges etc.

GRANITE TOP FIXING Over MDF Surfaces – Mirror polished, 18 mm Providing and fixing 18 mm thick gang saw cut mirror polished (pre-moulded and pre polished);machine cut for kitchen platforms; vanity counters, window sills, facia sand similar locations of required size of approved shade; colour and texture laid using Suitable Tile Adhesive including moulding and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any color and shade, upto 0.5 sqm. Job to be done as per specifications and directions of site engineer. Basic Cost of Granite Rs .1800 per sqm

RAISED ACCESS FLOORING IN SERVER ROOM

Uniformly distributed load - Panels shall be able to withstand Uniformly Distributed Load of 1350 Kg/sqm with capability to carry a uniform load of 200Kg on one square feet area at any location of the panel with maximum top surface deflection of 1.5mm. Permanent deformation of the panel should not exceed 0.25 after removal of load. Concentrated load - Panels shall be able to withstand Concentrated load of 450 Kgs placed on one square inch area using a round or square indentor at any location on the panel. Maximum top surface deflection not to exceed 2.54mm and permanent deformation not to exceed 0.25mm after removal of load. The panel shall be capable of withstanding the same concentrated load with maximum panel cutout of size 200mm dia. Ultimate load - Panel shall be capable of withstanding a concentrated load of 1500Kgs applied to one square inch at any location on the panel without failure.

ELECTRO STATIC DISCHARGE EPOXY FLOORING

Substrate Requirements : Concrete or screed substrate should be a minimum of 25N/ mm2, free from laitance, dust and other contamination. The substrate should be dry upto 75% RH, as per BS8204 and free from rising damp and ground water pressure.

Surface preparation : Removing the existing ESD Vinyl Sheet/flooring, followed by grinding the adhesive layer and ensure the concrete surface is exposed before the commencement of ANTISTATIC ESD FLOORING.

Antistatic System Application sequences :

1st Stage - Providing mixing and applying one coat of a Flowprime or Equivalent to seal the pin hole and to received the Scratch Coat / Underlay.

2nd Stage - Providing mixing and laying Epoxy Underlay with Flowshield SL UL or Equivalent at 2.0 mm thick to receive the subsequent tape and the conductive primer.

3rd Stage - Fixing the Copper tape of 12 mm wide, self-adhesive, conductive copper tape is always recommended in combination with any Flowcrete antistatic flooring system. The copper tape must be applied directly onto the cured Flowprime / Scratch Coat/Underlay, maximum 1 metre in from the perimeter of the application. Further, strips of tape should be applied within this area every 3 metres. Special attention should be paid to tape areas passing over expansion or bay joints to ensure permanent electrical continuity. The applied tape should be secure and fully bonded to a confirmed earth point. or as per the consultant requirement.(Under Civil Contrator scope)

4th Stage - Providing mixing and applying a conductive primer with Flowprime ESD Conductive or Equivalent prior to the commencement of the Epoxy Topping of Flowshield or Equivalent EDS SL 1000 Conductive.

5th Stage - Providing mixing and laying an ESD epoxy topping with Flowshield ESD SL 1000 Conductive or Equivalent, the ESD system is an Antistatic Epoxy Resin topping a hard-wearing, self-smoothing epoxy resin floor finish that complies with BS2050. finishing flooring using appropriate notch and spike roller to release the entraped air, the cured ESD topping shall exbihit the following properties ,following manufacturer's methodology and complete.

Typical properties

Fire Resistance EN 13501-1 Bfl - s1 Slip Resistance Dry>40, Wet depends on specification (in accordance with HSE and UKSRG guidelines). Temperature Resistance : Softens over 60 degree celcius Water Permeability Nil – Karsten test (impermeable) Hardness : 70 (Shore D) Abrasion Resistance Taber Abrader: 80 mg loss per 1000 cycles (1 kg load using CS17 wheels) Compressive Strength : 60 N/mm2 (BS6319) Flexural Strength : 40 N/mm2 (BS6319) Tensile Strength : 25 N/mm2 (BS6319) Bond Strength : Greater than cohesive strength of 25 N/mm2 concrete. >1.5MPa. Electrical Resistance :5.0 x 10^4 – 1.0 x 10^8 Ohms (BS2050

ELECTRO STATIC DISCHARGE VINYL TILE FLOORING

Supply & Installation of ESD Floors – PVC 2mm thick and the electro static dissipative will be homogeneous constructed product sliced from a pressed vinyl block to assure a highly flexible tile of dense construction, dimensionally stable, extremely hard wearing, with a completely non-directional pattern. Copper tape shall be layed at 900 mm grids. Copper strip grid to be formed in wall and floor at 900mm c/c bothways the joints to be rivited and connected to the earth strip & earthing. (Earthstrip paid separately)

COVING

Construction of Coving 75x75mm radial dimensions,Layering of the coving with resin rich putty. Over coated with recommended Epoxy Coating to match the floor finish all material and labour complete.

SS SHEETING - GROUND PLANE & WALL PLANE (EMI LAB)

Supply & Installation of minimum 2mm thick Stainless Steel material all as per technical requirement and manufacturer specification. The rates are inclusive of 2" floor to be raised with wooden platform required. Copper strip grid to be formed in wall and floor at 900mm c/c bothways the joints to be rivited with SS sheeting and connected to the earth strip & earthing. (Earthstrip paid separately)

FARADAY CAGE - WALL PLANE (RF LAB)

Supply & Installation of 2mm thick Aluminium Grade sheet for wall Cladding as per Faraday cage technical requirement manufacturer specification and to provide faraday cage required specification. Copper strip grid to be formed in wall at 900mm c/c bothways the joints to be rivited and connected to the earth strip & earthing. (Earthstrip paid separately)

FALSE CEILING

GYPSUM BOARD FALSE CEILING

CARPENTRY FALSE CEILING/ CORNICE Providing and fixing false-ceiling P/F gypsum false ceiling system using 12.5mm thick gypsum board and GI framework suspension system as per detailed specifications given below Providing and fixing seamless ceiling with gyp board of 12.5 mm thick, fixed to the underside of the suspended grid formed of GI ceiling section of 80 x 26 x 51 mm, perimeter channel of size 20 x 28 x 30 mm fixed along the wall by using wood screws and metal expansion rawl plugs. The GI intermediate channel of size 45 x 15 x 15 mm shall be fixed to the suspended strap hanger / GI ceiling angle at intervals not more than 1200 mm. The suspended GI ceiling angle / Strap hanger is tobe connected with GI soffit cleat and it should be fixed on the roof slab / beam, by using metal expansion fasteners (wt. Type) of approx.12.5 mm dia. The gyp board shall be fixed to the under side of the suspended grid by using 25 mm long dry wall screws. The joints shall be finished with joint fiber tape by using jointing compound as per manufacturers specification and applying over it 3 layers of the filler compound to provide a smooth surface. The ceiling surface shall be finished with one coat of primer, 2 coats of putty, three coats of acrylic emulsion etc. complete. The final coat shall be with roller finish. The rate shall include making cutouts for tube lights, spot lights, duct doors, for specified size, grills etc. for which no extra will be paid separately. Rate shall include providing additional trimming around cutouts for light fittings etc. and grills also for providing additional supports from ceiling where main / cross members are cut for light fittings etc. Rate shall include vertical as well as horizontal surfaces as per detailed drawing. Measurements shall be made on the basis of area calculated as per OBSERVABLE plan surface (horizontal or vertical). The finishes to the requirement of Tender Drawings / As per the approvals of BPCL Officer In-charge. Rate includes of necessaries hardwares , accessories, transportation, labour etc.,

MINERAL FIBRE BOARD FALSE CEILING

Providing & Fixing of Mineral Fibre Acoustical Suspended Ceiling System or Equivalent with Armstrong Dune Edge Tiles With Armstrong 15mm Exposed GRID. The tiles should have Humidity Resistance (RH) of 99%, NRC 0.5, Light Reflectance ≥85%, Thermal Conductivity k = 0.052 - 0.057 W/mK Colour White, Fire Performance Euro Class 0/ Class 1 as per BS 476 Pt - 6 & 7 Class A as per ASTM E-84 in module size of 600 x 600 x 15mm , suitable for Green Building application, with Recycled content of 38%. The tile shall be laid on Knauf(Armstrong) Silhouette profile grid system with 15mm white flanges incorporating a 6mm central reveal in black colour and with a web height of 38mm and a load carrying capacity of minimum 11.25 Kgs/M2 & pull out strength of 100kgs.. Silhouette, Main Runners & Cross Tees to have mitred ends & “birdsmouth” notches to provide mitred cruciform junctions. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with suspension system of Knauf(Armstrong) make. The Tile & Grid system used together should carry a 30 year warranty.INSTALLATION: To comprise main runner spaced at 1200mm centres securely fixed to the structural soffit using Commercial suspension system (specifications below) at 1200mm maximum centre. The First/Last Commercial suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall.Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees.Perimeter trim to be Knauf (Armstrong) wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centres.Commercial SUSPENSION SYSTEM - 2.5mm dia Gi wire for suspending, 6mm tie anchor & J hook waser nut level Adjusting. The measurement will be taken in flat / horizontal / linear alignment.

FALSE CEILING BOXING

Providing and fixing of 12mm thick MDF with 1mm thick Laminate of approved patterns and grooves as per the drawing over the ceiling grids (beam soffits & sides) sturdly fixed to RCC beams with necessary suitable size screws and as directed by Engineer-in charge.

CLEAN ROOM CEILING

Supplying & Fixing of Progressive type Double skin modular 50 mm thick Ceiling wall panel made of 0.5 mm thick Powder coated sheets on both sides with PUF as infill of density 40 ± 2 kg /m3, GI Profiles for reinforcement along the periphery with bottom Aluminium track, and necessary arrangements, All Joints shall be sealed with clean room compatible Neutral Grade Silicon Sealant.

STRETCH FALSE CEILING

Providing and fixing of approved make demountable curved/flat false ceiling made of Polyester knitted fabric coated with polyurethane 309 T Translucent white with printing as per Architect design, Weight: From 200g to 250g / m2. Fire Rating:B s1 d0 (Ex M1) / Flame retardant. Fabric has trans lucid fabric for back lighting purpose with CE (Complies with European Union norms), stretch on self supporting frame Profile. The rates should be inclusive with the necessary frame works for the fixing arrangement of approved make stretched fabric panels and the LED Light. The Shop Drawing to be submitted by the Contractor for approval.

ACOUSTIC SUSPENDED FALSE CEILING PANELS

Supply and installation of Anutone Subtex Shapes or Equivalent 30mm thk of 1200mm diameter,which are having glassfibre core, textured finish and are fully encapsulated. Panels are having density 100-120 kgs/m3 and weight 3-3.6kg/m2. Each panel is provided with 4 sets of accessories containing spring hooks, levelling clip and hanger wires. Springs to be rotated and anchored at back of each panel at four points to hold the panel stable. Supplied hanger wires to be first dropped from the beam/slab/truss to desired height with suitable cleats/anchor bolts. Anutone Subtex Shapes Hexagonal Nubby panels are then suspended using spring hooks and hanger wires and levelled into position with supplied levelling clips. The rate to include Cleats and anchor bolts. Technical Parameters: Fire (Class) – 1 & P, Acoustics – NRC upto 0.9, Thermal conductivity (W/mk)– 0.07, Climate (°C, RH) – 45, 95, Light reflectance (%) – 85, Green (VoC, RC %) – Low, 35.

CEILING PAINT

Providing and applying of Acrylic Emulsion paint on ceiling. Rate to include one coat of primer and 2 coats of black paint of approved shade.

JOINERIES

PATCH FITTING GLASS DOOR

Providing and fixing of fixed glass door with openable shutters using 12mm thick toughened glass. The fixed glass shall be fixed in position using PT patch fittings like PT 90/ PT 92 of Dorma make. The openable doors shall be fixed using top pivot PT 24, Top patch PT 20, bottom patch PT 10, corner lock US 10 with SS cover plates. The doors shall be fixed on floor spring model BTS 75V with SS cover plate. Pull handle shall be of size 600mm height x 32mm dia TGDI H 600. Necessary holes cutouts. etc to be provided as required. Cost to include drilling, cutting, necessary sealants, transportation etc in complete. The rate to be quoted will be inclusive of all the above including the cost of scaffolding, cost of floor springs and fixing cost for supply and erection of all hardware fittings such as S.S. handle two pairs, Equivalent for each door, all as directed by the Engineer in charge of the work and concreted civil works including chipping the floor, fixing the floor springs, making good the disturbed floor, all leads and lifts transport etc., complete. The glazing will be taped with 3M Scotchcal 7725SE-324 Frosted crystal film the details shown in the relevant drawings. The Frosted crystal film is to be supplied to the correct size and shape as indicated in the relevant drawing and the film is to be precut digitally with a plotter, brought to site and pasted over the glass. Any additional details required for shaping the film is to be obtained from the Architects in advance before precut the film.

SOLID FLUSH DOOR WITH VISION PANELS

Flush Doors With Vision Panel Providing and fixing in position Factory-finished Flush Doors of size as per Drawing with WALL LINE / approved equivalent make of Aluminium door frames of size 40x92mm. The frame finish shall be natural Anodized of 20 microns. Rate shall be inclusive of providing and fixing 35mm thick Factory-made Flush Door Shutters single leaf or two leaves solid core bonded with phenol formaldehyde synthetic resin thermo pressed with 8mm thick teak wood external lipping. The construction procedure of the shutter should be as per clause no.6 of IS 2202 (latest issue). The shutter shall be shop prepared for taking mortice lock or latches. Suitable lock block of wood may be provided for fixing the hardware. The size of block, shall perfectly correspond to the maximum size of lock covered in IS 2209 (latest issue). All the four edges of the door shutter shall be square. The shutter shall be free from twist or warp in its plane and of required size etc. complete as directed. Shutter to be finished with 1mm laminate of approved shade on both sides.The shutter will have vision panel of 8mm thick toughened glass of size, shape shown in the drawing will be fixed to the shutter frames and sides with 10 x 10mm wooden beading on all the sides as per shown in the drawing in required door Door shutters are to be fitted with the following hardware:- * 3 Nos. of S.S butt hinges - 125 mm * Door set mortice lock with S.S plate - 6 levers - 1 No. * Nylon door buffer of 35 mm dia - 1 No. * S.S 'H' handle of 600 mm height - 1 No. * S.S Door closer - 1 No. (slim pelmet arm type and of suitable load capacity)

MANUAL SLIDING GLASS DOOR

Supply and Installation of Manual Sliding Frameless glass door, MUTO Comfort L80 or Equivalent -Track with Wall Fixing having a Length of 3 mtr, Finish 157 - 1 PCE, MUTO Comfort L80 Cover Profile 3M,Finish 157 - 1 PCE, MUTO Comfort L80 M+L Cover Clip, 10 PC - 1 SET, MUTO Comfort L 80, set end caps, Finish 157 - 2 NOS., MUTO Comfort L 80, accessory set, Finish 157 - 1 SET, Flush Pull Knob for 8/10/12mm glass thickness- Finish : EV1- 1 PCE. Dimensions: Track width= 71mm, Track height= 58mm. Maximum door height is 3000mm. Maximum width is 1500mm. Class 4 Corrosion resistant according to EN 1670. Tested for 100,000 cycles. Compliant to DIN EN 1527. Max. door weight/double door is 80kg. Make : Dormakaba or Equivalent.Supply and Installation of Manual Single Sliding Frameless Glass Door MUTO comfort L80 with Door width of 1 mtr and Height of 2.4 mtr with a Glass thickness of 10mm

SLIDING CLEAN ROOM DOOR

Supply & Fixing of 60mm jam, Sliding door to fit flush into the blockwall/partition on both sides . Shutter sheet thk shall be 0.8mm and frame thk shall be 1.2 mm .Shutter with GI Sheet on both sides with powder coatinng in approved color with PUF as infill. Hardware include are Double Glazed view glass 300*300,Roller,lock,Sliding Rail, Guiding Pin ,Flush Handle.

CLEAN ROOM DOORS

Non-fire rated clean room doors Non Fire rated Clean Room Doors are made up of 0.8 mm sheet thickness for leaf and frame sheet thickness will be 1.2mm. Leaf thickness will be 40mm. Insulating material will be Honeycomb. Finish will be GI Powder Coated of approved colour. Jamb size will be 50-100 MM. The rate to include SS Hinges,Door Closer STD Arm,Dead Lock,B To B Handle Or Push Plate One Side,Drop Seal,Flush Bolt for Double Door only,Double Glazed Vision of Toughened Glass (5mm) Size (350x700 mm) with Black Ceramic Border with all fixing Accessories,Kick Plate - One sided(Made from SS-304, provided with all fixing Accessories)

Double Door (1800x2400)

Double Door (1500x2400)

Single Door (1000x2400)

Single Door (1200x2400)

FALSE CEILING TRAP DOORS

Providing and Fixing trap Doors for accessing the services and utilities in marine plywood 12 mm thick, with necessary sized Al/Hardwood framework, suspended from true ceiling bolted by anchor fasteners. Doors to be finished with 1 mm thick laminate/ paint as per site on both sides, edged with PVC transparent seal to prevent smells being sucked into the trap door space. The trap doors to be locked with Allen Keylocks with safety chain stays as directed complete Details, Design, Color, location & Pattern will as per the Architect Drawing/Engineer in Charge. Size as per site needs.

MODULAR FURNITURE

WORKSTATION LINEAR TABLE – TYPE A

Supply and Erection of Linear Workstation Dimension : 1200mm x 600mm x750mm Model No: Feather lite-Synergy or Equivalent Linear workstation Size: 1200 x 600D x 750Ht mm System: Desking - Synergy Specification Table top : 25mm thick Pre-laminate particle board E1 norms finished with 2mm PVC edge banding. Main Screen : 1050L x 450HT - 8mm thick Colored Glass Screen supported on studs Return Screen : 525L X 450HT - 8mm thick Colored Glass Screen supported on studs. Modesty : Considered SQ Perforated Metal modesty of 450mm HT only for End Legs for open passage areas and not for wall areas. Under-structure : Supported on MS powder coated Colors leg with supporting beams. Wire Management : 250mm Ht Raceway with 65mm Dia Wire Manager Grommet Specifications Vertical Raceway with built in separator for power and data of size 250H X 70mm thick with provision to mount switches and sockets on laminate facia with Vertical Wire Entry cover for wire uptake from floor to raceway with 65mm Dia Wire Manager Grommet. PEDESTAL (2D+1F) SIZE: 400L X 450D X 600HT Specifications: Table Top: 18mm thick pre laminated particle board ,Shutters: 18mm thick pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping Handle: Finger groove handle Lock: Regular lock * CPU trolley *ABS keyboard tray with mouse pad

WORKSTATION -TYPE B (L TYPE)

Supply and Erection of Linear Workstation Dimension : 1500mm x 1200mm x750mm Model No: Feather lite-Synergy or Equivalent Partition : Height – 1200mm frame with to pand sides in Aluminium trims and junctions with diecast caps. Table Top: 25mm thick Pre laminate particle board with 2mm PVC edge lipping on all exposed edges. Support: 18mm thick pre laminated gable ends. Wiremanagement: One metal raceway tile to mount switches below table top level for power and skirting tile for data Tile Finishes : Above table top Level: Fabric Tiles, one glass marker tile & one magnetic tile per workstation. Below table Top level: Pre-Laminated tiles and metal skirting tile on Main spine towards user.

CABIN TABLE – TYPE A

Supply and Erection of Cabin Table Dimension : 1500mm x 1500mm x750mm Model No: Featherlite -Senate HT -528 or Equivalent Specifications Table Top: 25mm thick pre laminated particle board Modesty storage panel 18mm thick Shutters: 18mm thick pre laminated particle board Edge: 25mm gable end Handle: in built handle Lock: Regular lock

CABIN TABLE – TYPE B

Supply and Erection of Cabin Table Dimension : 2100mm x 750mm x750mm Specifications Table Top : 25mm thick pre laminated particle board with 2mm PVC edge lipping in all exposed edges. Support : End Legs : MS powder Coated 50*50 PERFORM Legs Intermediate Legs : MS powder coated 60x40 mm legs and supporting MS Cross Beams (40x20mm) Wire management : * Continuous PVC Cable tray with provision to mount sockets & switches as per client requirement. * Vertical wire entry cover for wire uotake from floor to cable tray and 450mm Aluminium Flip up for switch access. Basic Cost : Rs.27000 or Equivalent

DISCUSSION TABLE – TYPE A

Supply,Fabrication & Fixing of 1500x750x900mm Discussion Table as per Architects Design. The 12mm thk Acrylic table top to be laid over 25mm MDF board with 6mm thk thermoformed acrylic drops over MDF backing. The table to be fixed onto wall/Partition on side. V shape Vertical Support to be fabricated from SS304 in the shape indicated by architectural Drawing. The rate to include snake wire manager,pop-up switch box and other accessories (SOLID ACRYLIC MAKE: CORIAN / MERINO HANEX/ LG HAUSYS) BASIC COST OF ACRYLIC SHEET- 6500/SQM

DISCUSSION TABLE – TYPE B

Supply,Fabrication & Fixing of 1500x600x750mm Discussion Table as per Architects Design. The 12mm thk Acrylic table top to be laid over 25mm MDF board with 6mm thk thermoformed acrylic drops over MDF backing. The table to be fixed onto wall/Partition on side. V shape Vertical Support to be fabricated from SS304 in the shape indicated by architectural Drawing. The rate to include snake wire manager,pop-up switch box and other accessories (SOLID ACRYLIC MAKE: CORIAN / MERINO HANEX/ LG HAUSYS) BASIC COST OF ACRYLIC SHEET- 6500/SQM

COFFEE TABLE

Providing and fixing Coffee table of size as per the drawing

The Table height will be 900mm as per the drawing. The table top and support to the table will be of 18mm thick MDF board finished with 12mm thick solid acrylic top of approved colour and shade. The Vertical Support and edges of the table will be 6mm thk Solid acrylic Surface with 3x6mm thk flexiply backing all as per the drawing and manufacturer specification for fixing. Additional support to be provided if required. The table will also have SS supports and snake wire manager to be provided as per the drawing. The rates are inclusive of Thermoforming application and necessary fittings etc., (SOLID ACRYLIC MAKE: CORIAN / MERINO HANEX/ LG HAUSYS) BASIC COST OF ACRYLIC SHEET- 6500/SQM

RECEPTION TABLE

Providing and fixing Reception table as per shape and size as shown in drawing. The Reception table top will be 18mm thick MDF finished with 1.0mm thick laminate and table will be made of 12mm toughened glass with bevelled edges and vertical support with 18mm thick MDF finished with 1.0mm thick laminate. The curved portion of the support will have 3 layers of 6mm thick flexible MDF finished with 1.0mm thick laminate as per size and shape etc. complete as per drawing. The table will have 12mm thick frosted glass fixed over the table fixed using 25mm dia SS Studs as shown in the drawing.

The table will also have wire manager. (basic cost Rs. 150 per each).The table is provided with storage unit of size 400 x 450 x 600mm height made out of 12mm & 18mm thick MDF and finished with necessary PVC banding, telescopic drawer sides, locking arrangement, 100mm long brush finish SS handles, rollers etc. complete all as per drawing. A trunking box and footrest to be provided made of 18mm thick MDF board as per the drawing to allow electrical and data cable to be concealed within.

All the exposed faces of the MDF finished with 1.0mm thick laminate. The concealed faces of the MDF is to be finished with 0.80mm thick laminate. The work is to be carried out in a first class workmanship manner all as per details shown in the drawing and as directed at site etc., complete. The rate to be include all the above. Note: All exposed MDF edges to be finished in PVC Edge banding as shown in the drawing. All steam beach timber members to be polished and finished in melamine. The rate to include the cost of back lighting for the Reception table. (Make for strip light: Philips, Sky cove) Samples of the Studs, SS Handles to be submitted for approval by Contractor. (Make for Laminate: Greenlam) (Make of sliders/ handles : Godrej/ EBCO/ Haffle)

CHAIRS

HIGH BACK CHAIR

High back chairs with synchronized tilt mechanism,gas lift,high back with fabricated tubular frame,powder coated and upholstered with "Flex XS" mesh fabric and cushion seat with two way adjustable arms,5prongs pedestal assembly of chrome base, twin wheel caster with nylon and seat finished with approved fabric Model: Featherlite -Astro HB or Equivalent ASTRO MBGS ADJ ARMS WITH HEADREST * Astro Medium Back Mesh Chair * Headrest * AC 60 Mesh * Fabric Upholstered Cushion Seat * Single Lock Synchro Mechanism * Adjustable Lumbar Support * One Way Adjustable Arms (Height) * Nylon Base Basic Cost : Rs.8800.00 or Equivalent

MEDIUM BACK CHAIR

Medium back chairs with synchronized tilt mechanism,gas lift,medium back with fabricated tubular frame,powder coated and up-holstered with "Flex XS" mesh fabric and cushion seat with two way adjustable arms,5prongs pedestal assembly, twin caster with nylon. * Contact Project Medium Mesh Back Chair * AN 70 Mesh * Fabric Upholstered Cushion Seat * Single Lock Synchro Mechanism * Adjustable Lumbar Support * One Way Adjustable Arms (Height) * Nylon Base Basic Cost : Rs.6000.00 or Equivalent

Providing of 1 Seater Sofa of approved type and size all as Directed by the Engineer-in-Charge. Single Seater sofa Pearl - Single seater sofa * Leatherette/ Fabric Basic Cost : Rs.20000.00 or Equivalent

LOW HEIGHT STORAGE

Supply and Erection of Low Height Storage Unit Model No: Featherlite – Executive serious SC-3 or Equivalent PRODUCT: Low Height Storage with Openable Shutter Specifications: 900x450x750mm Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed edges with 2mm thick PVC edge lipping Handle: Finger groove handle Lock: Regular lock Basic Cost : Rs.9300.00 or Equivalent

MEDIUM HEIGHT STORAGE

Supply and Erection of Medium Height Storage Unit Model No: Featherlite – Executive serious SC-3 or Equivalent PRODUCT: Medium Height Storage with Openable Shutter Specifications: 900x450x1200 Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed edges with 2mm thick PVC edge lipping Handle: Finger groove handle Lock: Regular lock Basic Cost : Rs.9800.00 or Equivalent

FULL HEIGHT STORAGE -TYPE 1

Supply and Erection of Full Height Storage Unit Dimension : 750*450*2100mm Model No: Featherlite – Executive serious SC-3 or Equivalent PRODUCT: Full Height Storage with Openable Shutter Specifications: 750x450x2100 Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed edges with 2mm thick PVC edge lipping Handle: Finger groove handle Lock: Regular lock

FULL HEIGHT STORAGE -TYPE 2

Supply and Erection of Full Height Storage Unit Dimension : 750*450*2100mm Model No: Featherlite – Executive serious SC-3 or Equivalent PRODUCT: Full Height Storage with Openable Shutter Specifications: 750x450x2100 Table Top: 18mm Thk pre laminated particle board Back: 9mm Thk pre laminated particle board with 2mm PVC edge lipping Shutters: 18mm Thk pre laminated particle board Edge: All exposed area with 2mm thick PVC edge lipping Handle: Finger groove handle Lock: Regular lock

OVER HEAD STORAGE

Providing and fixing Over Head storage to detail of drawing about 450mm wide and 600mm high comprising.

18mm thick MDF board fixed at top, rear sides and bottom at 75mm and one intermediate with necessary TW reepers and 10 x 37 mm steam beach moulding,along the edges.

Side hung shutters in 2 leaves with 18mm thick MDF board and on top finished with 1mm thick laminate of approved colour and shade,including necessary grooves, box type hinges,locking arrangements,100mm long S.S brush finish handles, Tower bolt, Ball catch etc. Complete.

Exposed faces of MDF board at top and sides of unit,finished with 1mm laminate of approved colour and shade.

All concealed faces of MDF board finished with 0.8mm thick laminate . All Exposed Edges to be finished with 2mm thick PVC Edge banding with suitable adhesive to the satisfaction of the client / Architect.

CROSSOVER BENCH

Supply,Fabrication & Fixing of Cross Over Bench of Dimension 1825x300x450mm. The Cross over Bench Will Be Finished with 1.50 mm thk Stainless Steel 304 Grade Sheet on all sides over MS Frame. The Cross Over table to Comply with relevant Clean room standards.

BOX FILE COMPACTOR(MOBILE SHELVING SYSTEM)

Manually operated and mechanically assisted mobile storage unit sliding smoothly & effortlessly on a pair of rails and providing maximum storage by compaction. Base Frame (Trolley) fabricated in channel type in 3 mm thick M.S. Sheet. TRACK: Trolley seating upon 30 mm square bar placed on 1.6mm thick M.S. plate which will be above the floor with multiples bends. For Five bay Three track. GUIDE RAILS: For movable unit we are providing guiderail bearing on base frame which closely move with trolley and the track as per the international standard of safety. SUPER STRUCTURE: Super structure of mobile storage systems 0.8mm thick C.R.C.A made TATA JSW. prime quality consist of knock down type panels. All the components such as shelves, front panel, end panel, vertical rear panel, centre partition etc., will act as an integral member of the unit. SHELVES: Shelves made of 0.8mm thick prime quality C.R.C.A having 8 folds each will be provided each design to carry a U.D.L. of 80-100 kgs and providing stiffener at the bottom of the each shelves. DRIVER COVER PANEL: Made out of 0.8mm C.R.C.A. thick prime quality cover the entire drive mechanism.

DRIVE MECHANISM AND HANDLE: Drive mechanism will be provided externally supported on special grade anti-friction bearing to have smooth and effortless movement. Entire mechanism or gear & sprockets (1/2’’) shall be incorporated within the front panel provided in the front of the unit. We are providing three spoke drive handles. POWDER COATING: Seven tank process powder coated, finishing up to 60 microns. Colour customized Standard colour RAL 7035 Structure. WHEEL: Made by MS Iron wheel OD 100MM.

Accounts room (1500x1680x2100)

CENTER TABLE FOR RECEPTION AREA– 550mmx550mm

Central Table with 18mm PLB Top and PC Swage Leg

Size : 550L x 550B

1. Everest White 2. Graphite Grey 3. Thanasu Maple 4. Classic Walnut

LOCKER

Providing of Lockers of compartment sizes 300x450x1200 (2 Compartments)

The lockers will be fully welded single unit of 18 gauge G.I Construction. The G.I. Sheets (TATA/JSW/ Equivalent) should have 120 gsm of Zinc coating and powder coating thickness should be minimum 80-100 microns. The cabinets must be completely welded for better strength & load bearing capacity. The loading partitions should be 16 gauge G.I. construction, welded to the carcass & should have necessary stiffeners.

The shutters & Drawers fronts will be made out of 18 gauge electro galvanized sheet with epoxy polyester powder coating. The G.I. sheets(TATA/JSW) should have 120 gsm of Zinc coating and powder coating thickness should be minimum 80-100 microns. The shutters & drawer fronts will have half round radius profile in order to avoid sharp edges

SPECIFICATION OF HARDWARE FITTING A) HINGES The hinges will be of nickel coated, self closing type with opening angle upto 90 degree, (Hettich / Hafele / Equivalent) fitted to the shutter with stainless steel screws/nuts & bolts.Special coating for hinges: The hinges will be of CED finish (Cathode Electrode Deposition) for enhanced chemical resistance.

B) ROLLER CATCH: A two-piece chemically inert nylon roller catch shall be provided on all base cupboard doors and shall be positioned near the pivoting edge of door to provide a clean unobstructed opening. Main body of the catch shall be confined within an integral cabinet divider rail, while latching post shall be mounted on the hinge side of door.

D) LOCKS : Square type multipurpose locks with 2 sets of keys, will be provided (Godrej/Equivalent)

Aluminium Skirting: providing and fixing aluminium skirting 100mm high and 1mm thick of approved make aluminium profile with natural color anodizing fixing at bottom of the partition (Approved Make : Wall line / Bottomline )

PELMET for glazing & pull down screen: Fabricating and installing the pelmet made out of 18MM thk plywood as per the required size and in line with external glazing as per architect's detail. Rates to include finishing exposed surfaces of the pelmet with enamel paint of approved shade and providing 50mm dia drills in the pelmet for return air if required. Pelmets should be ready to receive the Blinds.

Providing and fixing of 18 mm thick MDF MR 303 Ledge onto wall/Partition .Top & Sides of the Ledge to be Finished with 1.0mm thick laminate.

MISCELLANEOUS

PINUP BOARDS

Providing & fixing Fabric paneling or Soft boards with 12 mm MDF backing with P.E. Foam 2-4mm thick. Soft board to be provided with TW lipping. Soft board is covered with fabric of approved make, shade and then is fixed over the MDF board using headless nails as directed.

VINYL WALL GRAPHICS

Providing and fixing graphic vinyl complete with lamination to be applied on walls / partitions, of 3M/LG make (Code No. 180X series or approved equivalent) as per approved design and at specified locations as directed by Architect / Client. The rate shall be inclusive of preparing the base surface with 2 coats putty, and 1 coat oil primer with smooth finish, all complete and as directed. Rate shall be inclusive of all wastages, etc. Rate shall be inclusive of all wastages , Artwork design, download charges etc. Note : Only the actual installed area shall be measured for payment. Note:including image cost

DRY PANTRY COUNTER

Pantry Counter: providing and fixing of 12mm thick BWR plywood finished all as per the drawing. The rate to include the cost of opening for 6 Module flip up box(basic cost will be 700 each) as shown in the drawing. The shades & Sizes as mentioned in the Architectural drawing as approved by the Architect-in-charge.

FROSTED FILM FOR GLASS PARTITIONS/DOORS

Providing and Fixing of 3M Transparent Vinyl Film (optically cleared)/3M 1 Way Mesh Vinyl (with 3M Edge Sealer)/ 3 Frosted Vinyl printed with Colour Digital Print with UV Inks of approved shade and design. Basic Cost of Frosted Film Rs- 1600 per sqm

FLOOR MATS: Main Entrance

Providing and Fixing of Floor Mats at Main reception entrance of 3M Heavy Duty Nomad or approved equivalent.

Supply and installation of Wall clocks digital/ analogue of designer series. Basic Cost of Clock: Rs. 3750/Piece

PLANTER BOX

Providing & Fixing of 18mm thick MDF board finished with 1mm thick Laminate finish of Approved colour and Shade. The size and shape of the Planter Box as per architectural drawing.

Plant Pot : Pot made up of clay/ceramic along with the fertile sand/pebbles as per requirement of the BPCL in-charge

Artificial Plants Supply & installation of Artificial Indoor plants of approved design, inclusive of suitable light-weight soil mixture / equivalent medium to fix the same, etc complete and as directed.

Dust bins : Supply of 10 ltrs capacity perforated stainless steel dust bins for staffs . Make : Godrej, Nilkamal or approved make and specification.

Roller Blinds

Supplying & fixing approved shade and make Effective Optimized System Roller blinds Shade consists of sanitized treated, resilient and approved sample color polyester base fabric with high tear strength, Roller Tube, Control Chain, Control Set Left Hand, Control Set Right Hand, Bracket Cover, Chain Connector, O-C Bottom Rail String for conversion Spring, Bottom End Plug, Bottom End Plug Circular, Open Bottom Rail, Tube Bearing Plug etc.

Bunk Beds

Fabrication,Supply & Fixing of 950mm x 3785mm Bunk Bed over Workstations. Vertical Support will be fabricated with MS Pipe Supports from Floor & wall. 18mm MDF Board Finish with 1mm thick laminate to be laid over Horizontal MS Frame. Guard rail of 200mm Height to be provided. Additional Bracing to be provided as required. Rate to include: 1. Epoxy Painting on all the MS Sections. 2. Telescopic /Foldable Aluminium ladder.

PLUMBING WORKS

PART A: SANITARY FIXTURES AND CP FITTINGS

SS Sink with single bowl & Drain Board: Providing and fixing of Stainless steel sink(in weight) i/c waste pipe/bent etc. Complete with all respect. Make : Nirali/Franke or equivalent.

CP Sink Cock: Supplying and fixing of 15mm dia 'J' type CP sink cock with swinging spout (wall mounted model) for kitchen sink with CP wall flange etc. Notes: Conditions mentioned in item no.1 shall be applicable. Make : Kohler or Equivalent

Angle Stop Cock: Supplying and fixing of 15mm dia CP angle stop cock with wall flange etc.(for aqua guard point in Kitchen) Make : Kohler or Equivalent

PART B: UPVC PIPES AND FITTNGS (INTERNAL WATER SUPPLY):

Providing & fixing of UPVC schdule-40 pipes confirming to ASTM standard including all UPVC fittings like tees, elbows, bends, unions, coupling, reducer tees, collars etc. The work shall include cutting jointing with solvent cement pressure testing the joints / pipeline for 10 kg/sq.cm hydraulic pressure, for 2 hours hours etc., fixed on to the wall in vertical shafts / terrace with fabricated MS brackets of suitable size with GI 'U' clamps, bolts, nuts and GI washers including MS brackets including making good the walls and floors.

25mm dia

PART – C: PVC SOIL,WASTE,VENT PIPES AND FITTINGS ( INTERNAL )

Providing, fixing, testing and commissioning of PVC soil, waste and vent pipe confirming to IS 13592 of SWR quality( Type - B ) or 6 kg / sq.cm pressure rated including all fittings, like Bends, Tees, Elbows, Collars, junction, offsets, access pipes, jointing with solvent cement followed by application of leak proof adhesive like FRP paste & laid as ceiling hung system of inside the toilets, kitchen and utility to the required slope including necessary Clamp support & making necessary bores in walls as applicable, making good the bores with CM 1:3 or cement concrete as applicable, curing etc., complete.-75mm dia ( 6kg/sq.cm )

Providing, fixing, testing and commissioning of PVC Floor Trap of self cleansing design moulded or fabricated, if not available in size mentioned below, with or without vent arm jointing with rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste including PVC extension pipe for PVC / floor trap for with surface preparation with finishing etc., complete size: 100 mm dia x 400 mm length. Making good the floors.

Note: Rate is inclusive of bore hole packing and necessary support for the floor trap.

110mm dia x 75mm dia

Supply and fixing of 1 Hp motor for water supply . Rates are inclusive of testing & commissioning of motor

ELECTRICAL WORKS

Wiring of light, fan, 6A sockets and exhaust fan points

Supply and wiring for light points with 2 runs of 1.5 Sqmm FRLS, single core, multistrand copper wire ( For phase and neutral ) with one run of 1.5 Sqmm PVC insulated, single core, stranded, copper wire for earthing ( green colour ) in 20mm dia MS conduit, 16 Swg thick ( ISI marked ) with necessary accessories including supplying and fixing 6A single pole modular switch housed in manufacturers zinc passivated MS box with cover plate.

1 light controlled by 1 switch

2 lights controlled by 1 switch

3 lights controlled by one switch+external light points

Same item 1.1, but for 6A switched sockets including supply and fixing of switched sockets in independent locations ( Raw power ), excluding the work stations

Same as item no1.4, but socket and switch mounted in light control switch box

Call bell point with call button, rest button, buzzer and display

Supply and laying of 3 R 2.5 Sqmm FRLS stranded copper wire ( one for earth, green colour ) in 20mm dia MS conduit, 16 Swg thick ( ISI marked ) concealed in wall by chase cutting for circuit mains from LDBs to switch boxes

Supply and laying of 3 R 2.5 Sqmm FRLS stranded copper wire ( one for earth, green colour ) in 20mm dia MS conduit, 16 Swg thick ( ISI marked ) concealed in wall by chase cutting for circuit mains from ELDB 1,2 to Emergency switch boxes

Wiring for UPS sockets

Supply and laying of 3 R 2.5 Sqmm FRLS stranded copper wire ( one for earth, green colour ) in 20mm dia MS conduit, 16 Swg thick ( ISI marked ) concealed in wall by chase cutting and laying through partitions for UPS power sockets complete with all accessories ( 3 set of 3 nos 6A sockets to be connected to one circuit )

Supply and installation of 4 nos 6A switched sockets ,modular type housed in a single manufacturers zinc passivated MS box with cover plates. The boxes to be fixed either in wall or partitions/ work stations

Supply and laying of 3 R 4 Sqmm FRLS stranded copper wire ( one for earth, green colour ) in 20mm dia MS conduit, 16 Swg thick ( ISI marked ) concealed in wall by chase cutting and laying through partitions for UPS power sockets complete with all accessories ( 1 set of 2 nos 16A switched sockets to be connected to one circuit )

Supply and installation of 2 nos 6/16A switched sockets ,modular type housed in a single manufacturers zinc passivated MS box with cover plates. The boxes to be fixed either in wall or partitions/ work stations

Supply and installation of 16A DP switch housed in manufactures zinc passivated MS box (Work station master control) to be fixed in partitions for group control of 4 nos 6A switched sockets

Supply and installation of 1 nos 6/16A switched sockets ,modular type housed in a single manufacturers zinc passivated MS box with cover plates. The boxes to be fixed either in wall or partitions/ work stations

Supply and laying of 3 R 2.5 Sqmm FRLS stranded copper wire ( one for earth, green colour ) in 20mm dia MS conduit, 16 Swg thick ( ISI marked ) concealed in wall by chase cutting and laying through partitions for UPS power sockets complete with all accessories ( 1 set of 1 nos 16A switched sockets to be connected to one circuit )

Supply and laying of 3 R 4 Sqmm FRLS stranded copper wire ( one for earth, green colour ) in 20mm dia MS conduit, 16 Swg thick ( ISI marked ) concealed in wall by chase cutting and laying through partitions for UPS power sockets complete with all accessories ( 1 set of 5 nos 16A Combo switched sockets to be connected to one circuit )

Same as item no 2.2, but 5 nos 6/16A combo plug sockets ,modular type housed in a single manufacturers zinc passivated MS box with cover plates. The boxes to be fixed either in wall or partitions/ work stations

Raw power socket wiring

Supply and laying of 3 R 2.5 Sqmm FRLS stranded copper wire ( one for earth, green colour ) in 20mm dia MS conduit, 16 Swg thick ( ISI marked ) concealed in wall by chase cutting and laying through partitions for Raw power sockets complete with all accessories ( 4 or 5 set of 1 no 6A socket to be connected to one circuit )- For work stations

Supply and installation of 1 no 6A switched socket modular type housed in a single manufacturers zinc passivated MS box with cover plates. The boxes to be fixed either in wall or partitions/ work stations

Supply and laying of 3 R 4 Sqmm FRLS stranded copper wire ( one for earth, green colour ) in 20mm dia MS conduit, 16 Swg thick ( ISI marked ) concealed in wall by chase cutting and laying through partitions for UPS power sockets complete with all accessories ( 1 set of 4 nos 16A Combo switched sockets to be connected to one circuit )

Same as item no 2.2, but 4 nos 6/16A combo switched sockets ,modular type housed in a single manufacturers zinc passivated MS box with cover plates. The boxes to be fixed either in wall or partitions/ work stations

Supply and installation of 63A 4P mcb 10KA, for IEC connector with M.S enclosure

Supply and installation of 40A 4P mcb 10KA, for IEC connector with M.S enclosure

Supply and installation of 63A 3PH Meta clad socket with 63A 4P mcb 10KA, with M.S enclosure for SEM

Telephone / Data cables/ WIFI

Supply and installation of 25 mm dia PVC conduit, ISI marked medium grade to be laid on wall, and partitions from main Hub to all work stations as marked in the drawing.

Supply and installation of 20 mm dia PVC conduit, ISI marked medium grade to be laid on wall, and partitions from main Hub to all work stations as marked in the drawing.

Supply and installation of 25 mm dia PVC conduit, ISI marked medium grade to be laid on wall, and partitions from main tel junction to all work stations as marked in the drawing.

Supply and installation of 20 mm dia PVC conduit, ISI marked medium grade to be laid on wall, and partitions from main tel junction to all work stations as marked in the drawing.

Supply and installation of 2-pair telephone tinned copper cable 0.5mm dia copper conductor PVC insulated through the above mentioned conduit and terminations at both ends

Supply and installation of RJ-11 telephone socket mounted in manufacturers zinc passivated MS box

Supply and installation of 2xRJ-11 telephone socket mounted in manufacturers zinc passivated MS box

Supply and installation of 100-pair tel krone block housed in engineering plastic box with hinged and lockable transparent cover

Supply and installation of RJ-45 data socket mounted in GI anodized enclosure with cover plates

Supply and installation of Ee cat-6 network cable

Supply and installation of 24 port hub switch

Supply and installation of 24 port Loaded jack panel

Supply and installation of cat -6 1 mtr fly lead

Supply and installation of cat -6 2 mtr fly lead

Supply and installation of 24U hub rack-Floor mounted. Size – 1267mm High;600mm width;1000mm depth

I/O Point with box

Supply and wifi router with two LAN output with antenna type. D-Link DIR- 825 AC 1200 Wifi Dual-Band Gigabit (3LAN/1WAN) Router AC-1200 with 1.2 Gbps of speed/ 802.11a,802.11b,802.11g,802.11n,802.11AC.Dynamic IP(DHCP) : Yes WEP,WPA/WPA-2 (Personal/Enterprise),WPS ,Easy network management at your fingertips with D-Link Wi-F-APP.Dual band with 2.4 GHz band.

Supply of 4 port 10/100/1000 gigabit switch with 2 unink output

Light fittings

Supply , Installation including assembling, testing and commissioning of 600x600mm modular recess mounted with 38W LED (PHILIPS (PHILIPS RC380 LED 34S6500L60 PSU ODS1 ) and suspended from ceiling either with 20mm dia 16 Swg thick MS conduit ( ISI marked ) down rods( 0.8mt long approx: ) and heavy duty ball and sockets, sealing plate, check nuts etc or with 8 Swg GI chain and giving connections .

Supply,Installation testing and commissioning of 15W LED down lighter ( PHILIPS DN192B LED 95-6500PSU ) to be mounted on false ceiling

Supply , Installation including assembling, testing and commissioning of LED STRIP LIGHT-Phiips make

M.S Fabrication metrials

Supply and Erection of MS metrials

of cable tray supports,panel,etc

Distribution Boards

LDB -1,2, ELDB-1 & ELDB-2

Supply and installation of double door IP:43 6-way TPN MCB 7 segment type DB with following. The same shall be concealed to the wall

1 no main incomer feeder fitted with 40 A 4-pole MCB,10ka

3 nos incomer feeder fitted with 40 A 2-pole RCBO with 30ma sensitivity for phase incomer

18 nos of 6 A ,10kA SP MCBs as outgoing feeders ( 6 nos per phase)

Supply and installation of double door IP:43 6-way TPN MCB 7 segment type DB with following. The same shall be concealed to the wall

1 no main incomer feeder fitted with 63 A 4-pole MCB,10 Ka

3 nos incomer feeder fitted with 63 A 2-pole RCBO with 100mA sensitivity for phase incomer

18 nos of 16/20 A ( 6 nos per phase ) SP MCBs as outgoing feedrs

UPS DB-1,2

Supply and installation of double door IP:43 8-way TPN MCB 7 segment type DB with following. The same shall be concealed to the wall

1 no main incomer feeder fitted with 63 A 4-pole MCB,10 KA

3 nos incomer feeder fitted with 63 A 2-pole RCBO with 100mA sensitivity for phase incomer

18 nos of 20/16 A,10 KA (8 nos per phase ) SP MCBs as outgoing feedrs

Supply and installation of 40A FP MCB, 10 KA with M.S enclosure

Supply and installation of 63A FP MCB, 10 KA with M.S enclosure

Supply and installation of 125A TPN MCCB ,25 KA with M.S enclosure for UPS unit control

Supply and installation of 20A FP MCB 10 ka and DOL startor with M.S enclosure for Exhaust motor unit control

Supply and installation of 20A FP MCB, 10 KA with M.S enclosure

Supply and installation of 320A TPN MCCB ,25 KA with M.S enclosure for UPS unit control

Switch boards

Supply, erection, testing and commissioing of cubicle type switch board Floor mounted, fabricted with 16 Swg CRCA sheets with the following

Bus bar chamber consisting of 630A electrolytic quality CU busbars supported on SMC for phases and 400A for neutral. The busbars shall have colour coded PVC sleeving.The fault level shall be 36 Ka for 1 second.

Metering cubicle consisting of 1 no microprocessor controlled meter for reading all the electrical parameters like voltage, current, Kw, etc ( Socomec EM-VIFP ), LED type RYB indication lamps, 3 nos of resin cast CTs of ratio 630/5A class-1, 15 Va

1 no incomer feeder fitted with 1 no 630 A TP+N MCCB, 36 ka

1 no400A , 2nos 320 1no 160A TP+N MCCB, 25 KA, 3 no 125 A TP+N MCCB 25 ka as outgoing feeders

Panel will have a ring main earth bus with copper strip of size 25x3mm. All the switch frames and cubicles shall be connected to this earth which will be finally interconnected to external earth grid. .The panel shall be powder coated to siemens grey shade. .All internal wiring shall be carried out with adequate size copper wires.A detachable gland plate shall be fixed on the top of the cable alley for cable terminations. All MCCBs shall be fitted with front operating handle with door interlock

Supply, erection, testing and commissioing of cubicle type switch board Floor mounted, fabricted with 16 Swg CRCA sheets with the following

Bus bar chamber consisting of 160A electrolytic quality CU busbars supported on SMC for phases and 100A for neutral. The busbars shall have colour coded PVC sleeving.The fault level shall be 25 Ka for 1 second.

Metering cubicle consisting of 1 no microprocessor controlled meter for reading all the electrical parameters like voltage, current, Kw, etc ( Socomec EM-VIFP ), LED type RYB indication lamps, 3 nos of resin cast CTs of ratio 160/5A class-1, 15 Va

1 no incomer feeder fitted with 1 no 160 A TP+N MCCB, 25 ka

5 nos 63 A, 3 nos 40 A ,6 no 32A TP+N MCCB 25 ka as outgoing feeders

Panel will have a ring main earth bus with copper strip of size 25x3mm. All the switch frames and cubicles shall be connected to this earth which will be finally interconnected to external earth grid. .The panel shall be powder coated to siemens grey shade. .All internal wiring shall be carried out with adequate size copper wires.A detachable gland plate shall be fixed on the top of the cable alley for cable terminations. All MCCBs shall be fitted with front operating handle with door interlock

Supply, erection, testing and commissioing of cubicle type switch board Floor mounted, fabricted with 16 Swg CRCA sheets with the following

Bus bar chamber consisting of 400A electrolytic quality CU busbars supported on SMC for phases and 200A for neutral. The busbars shall have colour coded PVC sleeving.The fault level shall be 36 Ka for 1 second.

Metering cubicle consisting of 1 no microprocessor controlled meter for reading all the electrical parameters like voltage, current, Kw, etc ( Socomec EM-VIFP ), LED type RYB indication lamps, 3 nos of resin cast CTs of ratio 400/5A class-1, 15 Va

1 no incomer feeder fitted with 1 no 400 A TP+N MCCB, 25 ka

2 nos 125A ,3 nos 63A ,11 nos 40A TP+N MCCB 25 ka as outgoing feeders

Panel will have a ring main earth bus with copper strip of size 25x3mm. All the switch frames and cubicles shall be connected to this earth which will be finally interconnected to external earth grid. .The panel shall be powder coated to siemens grey shade. .All internal wiring shall be carried out with adequate size copper wires.A detachable gland plate shall be fixed on the top of the cable alley for cable terminations. All MCCBs shall be fitted with front operating handle with door interlock

UPS MAIN PANEL-1

Supply, erection, testing and commissioing of cubicle type switch board Floor mounted, fabricted with 16 Swg CRCA sheets with the following

Bus bar chamber consisting of 125A electrolytic quality CU busbars supported on SMC for phases and 100A for neutral. The busbars shall have colour coded PVC sleeving.The fault level shall be 25 Ka for 1 second.

Metering cubicle consisting of 1 no microprocessor controlled meter for reading all the electrical parameters like voltage, current, Kw, etc ( Socomec EM-VIFP ), LED type RYB indication lamps, 3 nos of resin cast CTs of ratio 125/5A class-1, 15 Va

1 no incomer feeder fitted with 1 no 125 A TP+N MCCB, 25 ka

6 nos 63 A TP+N MCCB 25 ka as outgoing feeders

Panel will have a ring main earth bus with copper strip of size 25x3mm. All the switch frames and cubicles shall be connected to this earth which will be finally interconnected to external earth grid. .The panel shall be powder coated to siemens grey shade. .All internal wiring shall be carried out with adequate size copper wires.A detachable gland plate shall be fixed on the top of the cable alley for cable terminations. All MCCBs shall be fitted with front operating handle with door interlock

UPS MAIN PANEL-2

Supply, erection, testing and commissioing of cubicle type switch board Floor mounted, fabricted with 16 Swg CRCA sheets with the following

Bus bar chamber consisting of 320A electrolytic quality CU busbars supported on SMC for phases and 200A for neutral. The busbars shall have colour coded PVC sleeving.The fault level shall be 25 Ka for 1 second.

Metering cubicle consisting of 1 no microprocessor controlled meter for reading all the electrical parameters like voltage, current, Kw, etc ( Socomec EM-VIFP ), LED type RYB indication lamps, 3 nos of resin cast CTs of ratio 320/5A class-1, 15 Va

1 no incomer feeder fitted with 1 no 320 A TP+N MCCB, 25 ka

10 nos 63 A TP+N MCCB 25 ka as outgoing feeders

Panel will have a ring main earth bus with copper strip of size 25x3mm. All the switch frames and cubicles shall be connected to this earth which will be finally interconnected to external earth grid. .The panel shall be powder coated to siemens grey shade. .All internal wiring shall be carried out with adequate size copper wires.A detachable gland plate shall be fixed on the top of the cable alley for cable terminations. All MCCBs shall be fitted with front operating handle with door interlock

UPS Main wiring

Supply, installation, testing and commissioining of 4R 35 Sqmm FRLS multistranded copper wire in 40mm dia 16 swg thick MS conduit ( ISI marked ) from ups , to ups interlocking panel

Supply, installation, testing and commissioining of 4R 150 Sqmm FRLS multistranded copper wire in 4R 50MM mm dia 16 swg thick MS conduit ( ISI marked ) from ups , to ups interlocking panel

Power wiring

Supply and installation of 6/16A modular type switched socket housed in manufacturers zinc passivated MS box to be concealed on the wall

Supply, installation, testing and commissioining of 3R 2.5 Sqmm FRLS multistranded copper wire in 20mm dia 16 swg thick MS conduit ( ISI marked ) from PDB and UPS DB , to 16A switched socket power circuits

Supply and installation of 20A Metal Clad socket housed in manufacturers zinc passivated MS box to be concealed on the wall

Supply, installation, testing and commissioining of 3R 4 Sqmm FRLS multistranded copper wire in 20mm dia 16 swg thick MS conduit ( ISI marked ) from PDB a/c power circuits for server room

UG cable

Supply and laying of 3.5x 300 Sqmm AL AR XLPE cable to be clamped on wall with GI clamps/ laid in excavated trenches etc ( Main cable for MSB and ups panel -2 )

Supply and laying of 3.5x 150 Sqmm AL AR XLPE cable to be clamped on wall with GI clamps/ laid in excavated trenches etc ( Main cable for UPS PANEL-2 )

Supply and laying of 3.5 x 95 Sqmm AL AR cable to be clamped on wall with GI clamps/ laid in excavated trenches etc ( for SSB-1 )

Supply and laying of 3.5 x 70 Sqmm AL AR cable to be clamped on wall with GI clamps/ laid in excavated trenches etc ( for CHILLER )

Same as item no 11.1, but 4x10 Sqmm CU AR cable along with 2R 10 SWG copper wire

Same as item no 11.1, but 3x6 Sqmm CU AR cable

Same as item no 11.1, but 4x6 Sqmm CU AR cable along with 2R 10 SWG copper wire

Same as item no 11.1, but 4x4 Sqmm CU AR cable along with 2R 12 SWG copper wire

Terminations of following cable with SIBG glands and copper crimping sockets and earthing of glands with copper clip and connecting the same to earth grid with 14 Swg copper wire. (Single Compression)

3.5x300 Sqmm

3.5x150 Sqmm

3.5x95 Sqmm

3.5x70 Sqmm

4x10 Sqmm

4x6 Sqmm

4x4 Sqmm

Earthing

Supply, installation, testing and commissioing of CU pipe electrode 40mm dia 3 Mt long, 3MM Thick as per IS-3043 complete with all accessories like watering funnel, clamps etc.The same to be installed in a pit 3 Mt deep and filled with alternate layers of charcoal, salt mixed with river sand. A brick work masonary shall be constructed of size 450x450x150mm and cement plasted at both inside and outside walls. A 3mm thick cast iron plate with frame work shall be placed over the chamber ( 12 nos for general earthing )

Supply and installation of 25x3 mm copper strip to interconnect the earth pits with SSB and other equipments

Supply and installation of 10 Sqmm multi strand copper wire FRLS insulated to be drawn in 25mm dia PVC conduit 2mm thick and to be clamped partially on wall with GI clamps and partially burried in ground and terminations at both ends with copper crimping sockets ( For lab earthing )

Public address system wiring

Supply and installation of 2 core 24/0.2mm dia twin twisted copper conductor PVC insulated cable drawn in 20mm dia medium grade PVC conduit ( ISI marked ) including clamping the same with GI clamps on ceiling, wall, through partitions etc and chase cutting of wall wherever required

Supply and installation of 6W ceiling mounted ring speaker in plastic mould with built in transformer

Supply and installation of volume control housed in GI box

CCTV Cables & Camera

Supply and installation of 25 mm dia PVC conduit, ISI marked medium grade to be laid on wall, and partitions

Supply and installation of 20 mm dia PVC conduit, ISI marked medium grade to be laid on wall, and partitions

Supply and installation of 16 channel DVR TURBO(Hikvision)

Supply and installation of 2 MP Camera Bult TURBO (Hikvision)

Supply and installation of 2 MP Dome TURBO (Hikvision)

Supply and installation of 8 channel Adapter

Supply and installation of 1 TB Hard disk (seagate/wd)

Supply and installation of 1+3 CCTV cable

Supply and installation of 2U Rack.Size = 150mm Height,550mm Width,350mm Depth.

Supply and installation of BNC Enclosure (pvc box) & INC

Supply and installation of 24" Monitor

Supply and installation of 42" TV

Safety Items

Supply and installation of 2.5 Kg capacity dry powder filled fire extinguisher to be mounted on wall with suitable supports ( UPS room and panel room )

Supply and installation of enamelled type danger board

Supply and installation of fire buckets complete with floor mounting stand ( 2 buckets in one stand ) buckets to be filled with dry sand ( 1 no in panel room )

Supply and installation of shock treatment chart with glass frame to be mounted on wall ( panel room and kitchen )

Supply and installation of 1200 mmx600mmx10mm size corrugated rubber mat to be spread in front of all ,LT panels and the same shall be tested for 1.1 Kv voltage.

Rubber hand gloves tested for 12 Kv

First aid box with necessary medicines, bandages, cotton etc

Cable tray

GI perforated tray-jindal / tata. (all accessories is your scope)- Note : Galvanisation to be Pre-Galvanised.

Supply, installation, testing and commissioing of GI perforated tray width-600mm hight-50mm

Supply, installation, testing and commissioing of GI perforated tray width-450mm hight-50mm

Supply, installation, testing and commissioing of GI perforated tray width-300mm hight-50mm

Supply, installation, testing and commissioing of GI perforated tray width-100mm hight-50mm

HVAC SYSTEM

Supply, Installation, Testing and Commissioning of AHU ceiling suspended AHU as under:

- Modular AHU panels with GI sheet of 0.60 mm thick for both inner & outer casing with 25 mm insulation sand witched in between. The outer panel shall have pre coating for corrosion resistance as also to provide a very good finish.

- Blower section with forward curved centrifugal fan with TEFC motor (IP 55 and Class F insulation).

- Drain section with 1.2mm SS drain pan.

- Coil section with 6 row chilled water coil, Slimseal BF valves at inlet/ outlet, drain and purge connections.

a. Flexible connection the outlet.

b. AHU sub panel with isolator and starter (Star/ Delta) with lockable OFF pushbutton.

c. Fresh air cowl with screen and damper.

d. Masonry Blocks of 150 mm height placed below the AHUs.

e. Power wiring with 3 C x 16 sqmm. PVC armoured copper cable with end terminations and two runs of 6 SWG copper earth rods (approx length - 20 M)

f. Inlet and outlet isolating valves of 65 mm dia:

g. 3-way mixing valve with all connections and control wiring

h. Pressure gauges and thermometers at inlet and outlet

i. Dehumidification heater banks to be provided for RH control within range of 40-60% RH (for the 12 TR and 14 TR units)

NOTE: The AHU will be provided by the builder. Only the above mentioned accessories are to be provided by the successful bidder

Ceiling suspended AHU, 30 mm SP:

a. 7 TR CSU, 2800 CFM, 30 mm SP (with pre filter only) for the general office area:

b. 12 TR CSU, 4800 CFM, 110 mm SP with pre and microvee filter for SSMG & Analytical lab. This will be connected to terminal hepa filter.

c. 14 TR CSU, 5600 CFM, 110 mm SP with pre and microvee filter for RF and EMI lab. This will be connected to terminal hepa filter.

Accessories for floor mounted AHU Complete as under:

- Microvee filter section

- Flexible connection the outlet.

- VFD driven AHU panel controlled by the temperature and ON/OFF controller at each individual lab area

- Fresh air cowl with screen and damper.

- Differential pressure switch for indicating the hepa filter condition (one each for SSMG, Analytical, RF, EMI, Development room, MPCVD)

- One digital thermometer and humidity indicator for each lab (one each for SSMG, Analytical, RF, EMI, Development room, MPCVD)

- UV lamp

- Dehumidification heater banks to be provided for RH control within range of 40-60% RH

- Masonry Blocks of 150 mm height placed below the AHUs.

- 3-way mixing valve with all connections and control wiring

All the above and capacities as under:

Floor mounted AHU accessories for:

35 TR, 60 mm SP floor mounted AHU

NOTE: The above AHU will be connected to terminal fan filter unit for HEPA filtration in the development lab & MPCVD labs

NOTE: One floor mounted 35 TR, 14000 CFM floor mounted AHU compatible to VFD drive shall be provided by the building owner

Supply, Laying, Pressure testing and insulating of chilled water piping, complete with fittings, supports and insulation. Insulation of 50 mm thick TF quality thermocole with 22 G Aluminium cladding. Insulations shall be as under/as per IS 1239, Mild Steel heavy (Class C) class pipe:

a. 100 mm dia:

a. 80 mm dia:

a. 65 mm dia:

b. 50 mm dia:

Drain piping from the AHU with PVC piping and insulated as required:

- 50 mm dia:

- 32 mm dia:

- 50 mm dia drain valve:

- 32 mm dia drain valve:

Supply and laying of aluminium ducting, complete with anchor fasteners and MS supports, angle bracings as required, nut, bolt & gasket etc

22 G ducting:

20 G ducting:

Supply and laying of galvanized sheet steel ducting with class VIII quality of zinc coating, complete with anchor fasteners and MS supports, angle bracings as required, nut, bolt & gasket etc

a. 24 G ducting:

b. 22 G ducting:

c. 20 G ducting:

Supply and laying of aluminium spiral ducting, complete with anchor fasteners and MS supports, angle bracings as required, nut, bolt & gasket etc

22 G ducting:

20 G ducting:

Acceptable makes: GI sheets: Jindal/ Nippon/ SAIL/JS or equivalent

Supply and fixing of volume control dampers -20G,22G

Supply and installation of powder coated Al. Supply air grills and return air outlets: (Note : Quote to be in Sqm.Final payment will be made on actuals)

a. Supply air grille with damper

b. Return air grille w/o damper.

c. Supply air diffuser with damper (circular/square)

d. Return air diffuser without damper (circular/square)

e. Ceiling suspended laminar flow SS plenum for labs comprising as standard feature with HEPA filter efficiency not less than 99.97% at 0.3 Microns (Factory DOP tested). with air flow at approx. 90-100 Fpm velocity. Each HEPA filter - 2 ft x 2 ft This is to be mounted only for the ceiling suspended units 14 TR and 12 TR for the RF/EMI & SSMG/Analytical labs

f. Ceiling suspended fan filter unit of SS construction complete with independent fan with HEPA filter efficiency not less than 99.97% at 0.3 Microns (Factory DOP tested). with air flow at approx. 90-100 Fpm velocity. Each HEPA filter to take care of 750 CFM capacity. These units are only for the development lab and MPCVD labs

Fan filter units, 750 CFM capacity

Acceptable makes: Air Master/ Air Breeze/System Air/AAF or equivalent.

g. Floor/wall mounted fan filter unit of SS construction complete with independent fan with HEPA filter efficiency not less than 99.97% at 0.3 Microns (Factory DOP tested). with air flow at approx. 90-100 Fpm velocity. Each HEPA filter to take care of 750 CFM capacity. These units are only for the development lab and MPCVD labs

Fan filter units, 750 CFM capacity

Supply and installation of fusible link type fire damper. (Note : Quote to be in Sqm.Final payment will be made on actuals)

Supply and laying of thermal insulation of ducting with 15 mm thick nitrile rubber, laminated with Aluminium foil

Acceptable makes: Armaflex, Armacell, A-flex, k-flex or equivalent

Supplying and installation of acoustic insulation of ducting with 19 mm thick armasound or equivalent material.

Acceptable makes: Armasound or equivalent

Supply and installation of acoustic insulation for the walls of the AHU room with 25 mm thick armasound or equivalent material.

Charges for air balancing the system as per specification. (Note : Air balancing is a simple task . No further specification required).

Individual temperature & ON/OFF controller in each lab which controls the VFD drive of the AHU. This is to be wall mounted and complete with control wiring to the damper & VFD control of the AHU. (Note: Standard accessory available)

VAV damper box with electric actuator controlled by the individual room thermostats. (Note : Quote to be in Sqm.Final payment will be made on actuals)

Pressure sensor - duct mounted

SITC of chilled water compact cassette unit (1 TR capacity) complete with all fittings and accessories for the UPS and server room with a 24 hour auto timer

EXHAUST SYSTEM

SITC of 1000 CFM centrifugal online exhaust fan for the rework station to be connected to the toilet exhaust like. 20 mm SP complete with base frame, TEFC squirrel gauge class F IP 55 motor, drive set, inlet and outlet flexible connections, etc with DOL starter panel along with 3 C x 4 sqmm. PVC armoured copper power cabling Acceptable makeS: Almonard/Kruger/Nadi/Nicotra/Lau or equivalent

- Supply and laying of galvanized sheet steel ducting with class VIII quality of zinc coating, complete with anchor fasteners and MS supports, angle bracings as required, nut, bolt & gasket etc - 24 G for exhaust system Acceptable makes: GI sheets: Jindal/ Nippon/ SAIL/JS or equivalent

- Supply and installation of powder coated Al. exhaust air outlet grille without damper for exhaust system Acceptable makes: Air Master/ Air Breeze/System Air or equivalent

b. All fixing fasteners shall be of corrosion resistant material like brass/GI.

FIRE PROTECTION SYSTEM

PART - A: SPRINKLER SYSTEM

Providing and fixing of MS ‘C’ class heavy duty sprinkler piping with welded joints including all fittings, fixed on the ceiling with MS brackets at every 2500 mm. The entire piping system shall be pressure tested to a pressure of 15 Kg/ sq.cm and held for 4 hours. The pipe and supports, after pressure testing, are to be applied with one coat of zinc chromate primer paint and two coats of PO red synthetic enamel paint. The piping system shall be done as per the directions of engineer in charge.

a) 300 mm dia:

b) 200 mm dia:

c) 150 mm dia:

d) 100 mm dia:

e) 80 mm dia:

f) 65 mm dia:

g) 50 mm dia:

h) 40 mm dia:

i) 32 mm dia:

j) 25 mm dia:

Supply, erection and commissioning of brass, quick response sprinklers of 68 deg C fire rating, complete with fixing to the sprinkler pipe as under:

a. Pendant type sprinkler

b. Side wall sprinkler

Supply and laying of metallic flexible hose of suitable dia and about 1500 mm long for fixing the sprinklers to the main pipe wherever false ceilings are provided. (Note : Dia will be determined in detailed engineering)

Water flow switch.(Note : Size will be determined in detailed engineering)

SITC of water motor alarm gong complete with all isolation and drain valves with fittings

Providing and fixing of heavy duty CI isolating valve for the sprinkler piping (without valve chamber)

100 mm dia:

80 mm dia:

50 mm dia (Drain valve):

(Make of valve – Audco, butterfly type)

Supply and fixing of GI perforated cable tray, size as under, for support/ concealment of small bore sprinkler pipes running in the hospital corridor and areas without false ceiling. The GI sheet shall be 1.5 mm thick and supported from the ceiling slab/ beam by means of GI threaded 12 mm rod at suitable intervals. (Note : Galvanisation to be of Pregalvanised)

Size 300 mm:

Size 450 mm:

Submission of drawings to the concerned Fire Officer for the entire fire system, getting approval for the drawings, arranging inspection and getting safety certificate for the entire installation from the concerned fire officer.

PART B - Fire Extinguishers

Supply and fixing of portable fire extinguishers manufactured as per IS with ISI marked suitable for wall mounting / floor mounting / trolley types with all accessories.( Note : ISI Approved makes )

Fire extinguishers of DCP type 4.5 kgs

Fire extinguishers of CO2 type 4.5 kgs

Fire extinguishers of ABC type 4 kgs

PART B - FIRE ALARM SYSTEM

Supply, Installation, Testing and Commissioning (SITC) of a Standalone micro processor based addressable type fire alarm panel, of 1 loop, complete with battery back up for 8 hours of operation of the panel with 30% of the detectors in operation.This panel is to be interlinked with the main building fire alarm panel

SITC of Multicriteria smoke cum heat detectors below the false ceiling

SITC of Multicriteria smoke cum heat detectors above the false ceiling

SITC of manual call point near exits

SITC of dual tone electronic hooter

SITC of 24 V power supply

SITC of response indicators

SITC of Heat Detector for electrical and communication rooms

Supplying and laying of interconnecting copper cabling of 2 x 1.5 sqmm FRLS cable

Other accessories like end of line resistance etc as required.(Note : Contractor to be determined during detailed engineering.)

Providing Air conditioning trip module within the panel as required

Perforated PVC trunking channel 25 mm x 25 mm for covering the electrical cable

Input module for flow switch

Short circuit isolators. (Note : Ratings are N/A)

Note : FAS is to be compatible to the building FAS Provided