KMC/WS/GJKBPS/25-26/08

CHAPTER - VIII SUPPLYING OF MATERIALS 8.8 Ductile iron double flanged manually operated sluice valve generally conforming to IS : 14846, having body, door, dome, gland in graded ductile iron to IS 1865, four faces and spindle nut of gun metal to IS : 318, inside screw non- rising stainless steel AISI-410 spindle valves suitable formaximum working pressure of 10 kg/cm... and body tested 15 kg/cm..., flanges flat faced and drilled to IS: 1538 :1993. Valves tested by closed end method only. 350mm and above valves are complete with enclosed gear box with anti friction device.Diameter in mm 400

CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.1.6 Flange joint to C.l./D.l/MS. pipes and specials including supply of rubber gasket. nuts. bolts. washers etc. of best quality to make the joint watertight at required hydraulic pressure all complete as per specification & direction of the Engineer-in-Charge. Diameter in mm 400mm dia.

CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.4Valves 2.4.1 Lowering, fitting and fixing of all types of valves in proper position and alignment using chain pully block or crane(for diameter above 250 mm) by providing temporary support,as required,gaskets,nuts& bolts etc.all cornplete as per specification and direction of the Engineer-in-Charge.[The rate Includes cost of flange joints]400mm dia.

CHAPTER - VIII SUPPLYING OF MATERIALS M.S. blank Flange as per IS-6392 TABLE 20 for 50 mm to size & for 200mm & above as IS -6329 Table-14)thickness 20mm-22mm NB Diameter in mm 400

CHAPTER - VIII SUPPLYING OF MATERIALS Supply of M.S. Flange (slipper type) as per IS-6392 TABLE 17 Thickness - 20mm -22mm NB Diameter in mm 400

REMOVAL OF ACTUATOR FROM THE EXISTING VALVE AFTER DISCONNECTION OF 415 V, 50 HZ , 3 -PHASE POWER SUPPLY CABLE FROM THE CONTROL CIRCUIT, EARTHING CABLE ETC WITH PROPER CARE AND PLACING IT IN A SUITABLE PLACE USING DEPARTMENTAL OVER HEAD CRANE ETC COMPLETE AS PER DIRECTION OF EIC.( RATE ANALYSIS APPROVED BY DG WS DATED 02/1/2019)

SUPPLY & DELIVERY OF SYNCROPACK ELECTRICAL MOTORISED ACTUATOR (WITH F14 MOUNTING) WITH INTEGRAL CONTROL AND STARTER, SYNCHRO PHASE PROTECTION ANTI HAMMER PROTECTION, SINGLE PHASE PROTECTION , JAMMED VALVE MOTOR PROTECTION, 2 NO. TORQUE/UNIT SWITCHES (SPARE 1 NO/1 NC CHANGEOVER CANTACTS) 4 NO AUXILERY LIMIT SWITCHES (SPARE 1 NO/1 NC CHANGEOVER CONTACTS) AND CONTINUOUS POSITION INDICATOR (MECHANICAL AND ELECTRICAL) WITH HAND WHEEL DRIVE AND HAND AUTO LEVER, AUTO LEVER SUITABLE FOR BUTTERFLY VALVE.(INCLUDING DIGITAL POTENTIOMETER) O/P TORQUE 600 NM O/P SPEED 12 RPM (FAIR RATE HAS BEEN APPROVED BY DG WS DTD. 01.08.2025)

RE-INSTALL THE COMPLETE ACTUATOR ON THE VALVE GEAR BOX , RECONNECTION OF POWER LINE AND CONTROL CIRCUIT WITH PROPER CABLE GLANDS AND EARTHING CONNECTION AND COMPLETE SWITCH SETTING BOTH OPEN & CLOSE WITH PROPER SYNCHRONIZATION OF ELECTRICAL OPERATION FROM OPERATING PANEL / CONTROL DISK ETC COMPLETE AND COMMISSIONING AS PER DIRECTION OF EIC.( RATE ANALYSIS APPROVED BY DG WS DATED 02/1/2019)

CHAPTER - VII MISCELLANEOUS ITEMS Dewatering by pumps including all leads, lifts and making all arrangements of disposal. where continuous flow of water from a source other than natural or ground water is encountered in case of emergency maintenance works related to leakage. breakage and making wet connections. [Note ;- In case of any other situation demanding such emergency dewatering. use of this item is to be approved by the Superintending Engineer/Tender Accepting Authority. This item shall be executed on the specific direction duly supported by proper clarification of the E.I.C. who will be satisfied in absolute discretion that such work has not been necessitated due to any natural source of water or any fault of the Contractor]

BUILDING WORKS (F) STRUCTURAL STEEL WORKS, GRILLS, GATES ETC. A. ORIGINAL WORKS 1. M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length,fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. Payment for gusset, bracket, cleat, rivets, bolts and nuts may be make by adding the actual weight of such items with the weight of finished structural members or 7% of weight for finished structural members weighing not less than 22.5 Kg. / m. or 15 % of weight for finished structal members weighing less than 22.5 Kg. / m. may be increased allow for bracket, cleat, rivet, bolts and nuts etc. and no seperate payment being made for these items, as per direction of Engineer In Charge. The rates are considered for a height of erection 8m. / 2nd floor level from the ground. Add 1.5% extra over the rate for each additional floor or 4m. beyond initiial 8m. or part thereof. I) For structural members of specified sections weighing less than 22.5 Kg./m

BUILDING WORKS (F) STRUCTURAL STEEL WORKS, GRILLS, GATES ETC. B. REPAIRING 2. Welding in M.S. structural work with gas or electric: (a) Tack weld

BUILDING WORKS (F) STRUCTURAL STEEL WORKS, GRILLS, GATES ETC. B. REPAIRING 2. Welding in M.S. structural work with gas or electric: (b) Continuous weld.

Sub Total

Please Enable Macros to View BoQ information