SPECIAL REPAIR OF TOILETS/BATHROOMS AND ROOF IN ADMINISTRATIVE BLOCK OF RAJ AT MILITARY STATION JAIPUR

Amount

Taking down cement plaster including raking out joints, hacking for key scrubbing down with water etc built in CM

M&L rendering 15 mm thick in CM(1:6) on brick walls or concrete surface, surface finished even and smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surface other than fair face of brick work of walls, finished fair & even.

M&L for rendering 10mm thick in cement mortar 1:3 on concrete surfaces including finished even & smooth without using extra cement on ceiling.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper of approved shade/tint over a coat of 1mm thick Birla wall care putty on walls all as specified & directed by Engineer-in-Charge

M&L for Two coats of Oil Bound Distemper on newly plastered surfaces of Ceiling over a coat of 1mm thick Birla wall care putty including preparation of surfaces.

M&L for preparation of new plastered surfaces and applying two coats of apex paint of approved shade over a coat of 1mm thick birla wall care putty on walls all as specified & directed by Engineer-in-Charge

M & L for preperation of old painted surfaces of wall and applying two coats of oil bound distemper on wall complete all as specified and directed by engineer in charge

M & L for complete removal of existing treatement from surfaces of ceiling and applying two coats of oil bound distemper over a coat of 1mm thick birla wall care putty on ceiling complete all as specified and directed by engineer in charge

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for.

M & L for PCC 1:2:4 type B1 using 20mm graded stone aggregates as in sub-base to floor or in sunken portion complete

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing)

S&F Coloured Glazed ceramic tiles size 300x450mm x 7mm thick edge cut/ joint free , on walls etc in the combination of light and dark shed concept . set & jointed in neat cement slurry & pointed in white/coloured cement to match over 15mm thick plaster in cement mortar (1:4)

S&F Coloured Non Skid ceramic tiles 7 to 8mm thick edge cut/ joint free (squares/ rectangular) area of each tile exc. 0.11 sqm but not exc. 0.18 sqm, in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match over 10 mm thick cement rendering in CM ( 1:4) finished fair and even .

M&L CP cast copper alloy bib taps two way with wall flange and areator fancy type of 15 mm bore quarter turn (Make-CERA CAT PART NO CQ 606or equivalent of MARC, JAQUAR) fixed in repair.

S&F PVC connection 15mm bore with 2 Nos PTMT nuts, 45cm long fixed with one end to pillar tap & the other end to stop cock or iron pipe all as directed by Engineer-in-charge.

M&L CP fancy Type center hole basin mixer 15mm bore cast copper alloy with 450 mm copper hose /braided hose without Popup waste system quarter turn (Make-CERA CAT PART NO CQ 615 or equivalent of MARC, JAQUAR)

M&L CP wall Mixer with flange & 115 mm long bend pipe forover head shower non Telephonictype with connecting legs wall flanges and crutch etc quarter turn ( Make-CERA CAT PART NO CQ 612 or equivalent of MARC, JAQUAR) 15mm bore for mixing hot & cold w

M&L Towel ring of brass CP Squar flange (Make-CERA CAT PART NO CQ 102 or equivalent of MARC, JAQUAR) and fixed in repairs

M&L Chromium plated Overhead Rain shower with relvoling joint and 115mmlong shower arm with wall flange 15 mm bore fancy type any colour (Make-CERA CAT PART NO CP 140 or equivalent of MARC, JAQUAR) and fixed in repair

M&L Chromium plated angle stop cock with wall flange fancy type cast copper alloy 15 mm bore any colour (Make-CERA CAT PART NO CQ 608 or equivalent of MARC, JAQUAR) fixed in repair

S&F in repairs Vitreous China wash basin, coloured oval sape , (COUNTER TOP), coupling and waste pipe fitted in granite counter slab of size 600mmx900mm, with pedestal stand compete all specified and directed by Engr-in-Charge ( Make-MARC CAT PART NO MAC 3020 etc)

Demolition of old existing unserviceable EWC seat and S & F Vitreous China coloured EWC wall mounted with flushing cistern incl PVC coloured sheet cover complete all specified by Engr-in-Charge .( Make-CERA CAT PART NO CQ 606or equivalent of MARC, JAQUAR etc)

S&F Waste fittings 32mm bore, brass, CP for glazed ware sinks, basins, etc. with long screwed shanks & fly-nuts, flange end bedded in red lead cement & other end fixed(Make-MARC CAT PART NO MAC 3020 or equivalentof CERA JAQUAR) fixed in repair

S&F CP bottle trap with internal partition 32 mm size with 300 mm X 190 mm long wall connection pipe and wall flange for WHB (Make-Make-CERA CAT PART NO CM 104 B or equivalent of MARC, JAQUAR) fixed in repair

S&F in repair stop valve 15mm, . copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F in repair Stop valves 20 mm bore, . copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions

S&F of CP pressure JET for EWC including flexible pipe for 15 mmdia bore

Dismantling of old U/S grating and M&L of PVC Nahani / floor trap and square in size of 100X100 mm including MS chromium plated grating 125mm dia of weight not less than 50gm for floor trap / Nahani trap.

Dismantling and taking up or down the existing unserviceable GI pipe and M&L for new galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors of following sizes :-

15 mm bore

20 mm bore

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 500 Ltrs Capacity including Dismantling water tanks.

S&F Ball brass valves 20mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule and fixed in repair

M&L for providing circular, raised platform of height 20 cm below the tank and base 15cm more than the external dia of thank of PVC cylindrical water tank of capacity 500/1000 liters using PCC 1:3:6 type c1 using 20mm graded stone aggregate with smooth finish

S&F vitreous china bowl urinal flat back,large size of 590 x 390 x 375 mm (minimum) white, with grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia.Make HINDWARE/Jaquar/Parryware or equivalent

S&F in repairs elegent mirror PVC cabinet with towel rail of size 475 x 600 x 150 mm all as specified

S&F Soap dish brass CP ((Make-CERA CAT PART NO CA 103 or equivalent of MARC, JAQUAR) fixed in repair

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors including dismantling of old pipe

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors including dismantling of old pipe

S&F PVC (SWR) bends any radius 75mm dia

S&F PVC (SWR) bends any radius 110mm dia

S&F PVC (SWR), junction single, (Single T) equal or unequal 75mm dia

S&F PVC (SWR), junction single, (Single T) equal or unequal 110mm dia

S&F PVC (SWR) vent cowl 110mm dia

M&L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement

M&L PVC (SWR) gully trap 125/110 mm, setting & jointing with solvent cement

M&L Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws(Make-CERA CAT PART NO CA 106 or equivalent of MARC, JAQUAR) fixed in repair

S&F bathroom Glass corner of best quality (as per sample)

M&L for Fancy type MS bracket suitable for curtain rod fixed in repair

M&L of 20 mm dia Drapery Fancy type curtain rod fixed in repair

M&L for Fancy type caps/ side Bulbs PVC powder coated suitable for curtain rod fixed in repair

Taking down Chowkats or frames exc 1.5 sq. m but n exc 4 sq m each with shutters (without taking off shutters from the frames)

All as per item No 52 above but area n exc 1.50 Sqm each.

Providing and fixing 28mm thick factory made PVC Supreme Door Shutter consisting of frame made out of m.S. tubes of 19 gauge thickness nd size of 40mmx20mm for stiles, top and bottom rails having a coat of steel primers of approved make and manufacture. M.S. Frame covered with 4mm thick heat moulded Prelam PVC 'C' Channel of size 28mm thickness,75mm width out of which 60mm shall be flat and 15mm shall be tapered in 45dgree angle on either sides forming stiles, top and bottom rail and 100mm wide Rajshri Prelam PVC sheet out of which 100mm shall be be flat and 15mm shall be tapered An additional of 5mm thick PVC sheet of 20mm width is to be stuck on the interior side of 'C' Channel using PVC solvent adhesive etc. complete on both sides to form lock rail.Lock rail shall be provided on either side of panel. Panelling of 4mm thick PVC sheet to be fitted in the MS Frame welded/sealed to the stiles with 8mm (4mm + 4mm) x 12mm wide PVC sheet as beading on inner side and 8mm (4mm + 4mm) x 20mm wide PVC sheet as beading on the inner tapered side of lock rails joined together with solvent cement adhesive. An additional of 4mm thick PVC sheet of 20mm width is to be stuck on the interior side of 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification and drawing.

Providing and Fixing Factory made Adjustable (PVC) Doorframe the size 65mm x 60mm with a wall thicknes of 4mm, made out of extruded 4mm PVC foam sheet, metre cut at two corners and joined with 2nos. of 150mm long brackets of 15 x 15mm M.S. Square tube. The two vertical door profile are to be reinforced with 40 x 20mm M.S. tube of 19 guage through out the frame. The doorframe shall be fixed to the wall using 65/100mm long M.S. Screw through the frame by using PVC fastners. A minimum of 4 nos. of screws to be provided for each vertical member & minimum 2 nos. for horizontal member etc. complete as per manufacturers specification and direction of Engineer-in-Charge.

S&F Pressed steel frames 105x60mm sieze for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position.

Cutting holes in stone / brick walls built in CM for inserting hold fast & making good dismantled portion in CM (1:3) depth of embaded portion of holdfast n. exc half brick

M&L of 35 mm thick of seconed class hard wood Plain framed panelled shutters (any numbers of panels ) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density wood particle board with comercial face veneers supplied and fitted and fitted to chowkates

S&F 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkats including welding complete.

S&F Aluminium, anodised, barrel tower bolts 150mm long of extruded section.

S&F Aluminium handles 125 mm size, . type, anodised

S&F MS spring hinges 300 mm, ordinary rat tail rod pattern including roller and roller plate complete fixed to wooden/ angle iron chowkats .

Demolition of PCC in roof covering, kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing treatment of any type all as directed by Engineer-in-charge.

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 25mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with WPC @ 3% weight of cement.

M&L Painting surface with one coat of polymeric primer @ 0.30 Kg per sqm, conforming to IS : 3384. A layer of APP based polymeric membrane, 3 mm thick (min), weighing not less than 3.5 Kg/m2 reinforced with polyster non woven fabric ( weighing not less than 150 gms/ Sqm). Application of polymeric membrane shall be by torch application all as per manufacturer instructions. and finally applying one coat of bitumen @ 1.2 kg/sqm on APP membrane before application of aluminium paint

M&L one coat of aluminium paint over APP Membrane all as specified and directed by Engineer -in - chage

Supply only integral water proofing compound.

M&L PCC 1:2:4 mix type B-0(using 12.5mm graded aggregates) as in roof kerbs rounded or chambered on edge.

Demolition of Stone slabs in roofs, suspended floors, chajjas, landings, etc. any thickness, jointed in any mortar

M&L for screed bed or bedding layer of cement mortar (1:4), 10mm thick for laying floor finishes.

M&L Granite 16 to 18 mm thick (of any tpe) work (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like in CM(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite

Cutting holes into or through cement concrete slabs, chajjas, etc. reinforced or otherwise superficial area N exc 100 sq cm

M&L Aluminium anodised frame fixed type of aluminium section weighing not less than 0.55 Kg/Mtr including necessary joining, cleats, glazing clips, rubber packing anodised aluminium snap beading, screws etc complete all as specified.

M&L Aluminium anodised window shutter openable type with aluminium section weighing not less than 0.55 Kg/ Mtr incl. necessary joining, cleats, glazing clips, rubber packing anodised aluminium snap beading, screws, handle, hinges & tower bolt etc complete all as specified

S&F 4mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq.m in each pane

Taking down carefully copper/ aluminum point wiring (light, fan, socket or power) complete including all fittings such as switches, ceiling roses, pendants, sockets, lamp holder, fan regulator brackets light fittings tube light fitting, bell/ buzzer etc (excluding fans) and making good disturbed surfaces of wall floors, ceiling etc complete all as specified and as directed by Engr-in-Charge to match with existing surface.

M&L Point wiring using approved colour coding as per IS, with stranded copper conductor 1.5 Sq. mm (nominal area), single core, FRLS insulated, PVC insulated and unsheathed stranded cable 1100 volts grade, confirming to IS-694/ISI marked in and including PVC casing caping, medium grade, ISI marked, with mild steel sunken boxes with earth dolly zink coated and including mounting frame and over cover plate, including PVC insulated stranded copper conductor 1.5 Sqmm (nominal area) single core cable as earth continuity conductor to common earth and connected FRLS cable 1100 V grade as continuous earth wire to earth dolly for followings.

One light/fan/ bell point controlled by one, one way switch.

One 3 pin 5 Amp socket outlet on the same board with other switches.

All as per Item No 78 above but with 2.5 Sqmm copper cable for 3 pin 15 Amps socket outlet on independent board, complete all as specified & directed by Engr-in Charge.

S&F switch, piano type 230/250 volts for the following:-

Single pole, one way 5 Amp rating

(b) Single pole, one way 15 Amp rating

S&F Socket outlet 3 pin 5 Amp 2 in 1 flush type, 230/250 Volts grade on top covers (catered in point wiring above)

S&F Socket outlet 3 pin 15 Amp flush type, 230/250 Volts grade on top covers (catered in point wiring above)

M&L Ceiling rose surface bakelite 65x50mm, three terminals. Make Anchor/Legrand/Crabtree

S&F Lamp holder insulated body with back plate for batten fitting. Make Anchor/bajaj/philips

M & L for exhaust fan 380 mm weep, metal body with louvers complete all as specified and directed Make : Crompton Ventilier or wquivalent in Bajaj, Havells, Usha

S&F LED retrofit lamp (Size-4 feet), Battern for LED tube, universal batten for T-5 lamps surface/ wall mounting IP 20 with twin core twisted flexible copper conductor cable with suitable size. Make:- Havells Cat No. REGALBATTENT5UPTO1X18WDSBSWH or equivalent

Supply & Fixing mirror surface mounted LED fitting 10 W (2 Feet) provided with a high outout PMMA diffuser for glare free light, IP 20 with high brightness LEDs complete iwth all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size.

S&F in repair factory made, sheet distribution boards, SP&N 8 ways, double door protection class IP-42 double door type suitable for mounting MCB/ MCCB, confirming to IS-13032, IS-8623, BS-5484 with minimum 200 amps, copper bus bar of the under mentioned rating :-

S&F in repair MCB 10 KA confirming to IS-8828 : 1996, IEC-898 : 1995 rupturing capacity of the under mentioned type and rating :-

(a) SP 5 to 32 amps

(b) SPN 32 to 63 amps.

M & L Sub main wiring complete with 2 runs of 6 Sqmm single core PVC insulated unsheathed cable 1100 V grade with multistranded copper conductor ISI marked drawn throughn and including PVC rigid conduit/casing capping and conduit accessories fixed on surface/wall celing etc including provision of 1 run of 6 Sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity.

MSR INFRATECH

UNIVERSAL INFRAPROJECT PVT LTD

M/S ROHIT CONSTRUCTION

JAGDAMBA CONSTRUCTION COMPANY

Baradwal Construction Company