SPECIAL REPAIR TO BOREWELL AND CERTAIN BUILDINGS INCLUDING PROVISION OF SHEDS ETC AT SEVOKE ROAD MIL STN UNDER GE SEVOKE ROAD

Amount

Schedule 'A'

Taking down cement plaster or lime plaster on walls / ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retrieved debris from the site of work etc complete all as specified and directed.

Taking down chowkats or frames , exc 1.5 sqm but not exc 4 sqm each with shutters (without taking off shutters from the frame) and removing from site of work complete all as specified and directed.

All as per item No 2.00 here-in-above but n. exc 1.50sqm each -ditto-

Demolition of cement concrete in ground floors (un-reinforced) and paving not ex, 15cm thickness (bellow or above ground level) including removing debris site of work complete all as specified and directed.

Demolition brick work built in cement mortar including disposal of debris, from site of work, complete all specified and directed.

M&L for brick work with sub class B old size bricks straight or curved on plan exc. 6mtr mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with sub class 'B' old size bricks straight or curved on plain to any radius, as in half brick thick wall built in CM (1:4) complete all as specified and directed,

M&L for rendering 15mm thick in cement mortar (1:6) on surfaces of walls including finishing the surfaces even and fair (without using extra cement) etc complete all as specified and directed.

M&L for rendering 20mm thick in cement mortar 1:4 in two layers 10mm thick each mixed with water proofing compound as per manufacturer's instruction , surfaces of top layer finished even and smooth (without using extra cement) complete all as specified and directed. Note : WPC shall be measured and paid separately as supply only)

M&L for rendering 5mm thick in cement mortar (1:3) to ceiling and finishing the surfaces even and fair without using extra cement, complete all as specified and directed.

Supply only integral water proofing compound of approved quality (ISI marked )complete all as specified and directed.

S&F second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints etc complete all as specified and directed.

S&F factory made 35mm thick plain, framed paneled shutter (two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12mm veneered particle board with commercial veneering in both faces. The size of rails and stiles shall be as per IS:1003 (Part-I) kiln seasoned and chemically pressure treated of 2nd class hard wood complete all as specified and directed,

S&F factory made 35mm thick 2nd class hard wood kiln seasoned and chemically pressure threated, glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edges, of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part-I (section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified and directed ,

S&F factory made solid Panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for sites and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet shall be fitted in the M.S frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed.

S&F MS hold fasts etc and similar small articles made out of mild steel flat etc of grade Fe-290 Gde-E-165 etc complete all as specified and directed.

M&L for PCC 1:2:4 type B1 cement concrete using 20mm graded aggregate as in bed blocks etc for hold fasts etc including provision of necessary from work, complete all as specified and directed.

Preparing surfaces of wood and wood based materials, steel and iron work, new or old of any description and girth not otherwise described and treated with tar or coal tar black paint, complete ass as specified and directed.

S&F standard aluminium section powder coded in partition / frame and door shutter, sliding windows / ventilators and places otherwise not specified cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass or wire cloth or bakelite sheet and all necessary fittings, hinges, screws, plugs, locking arrangements for windows, Nylon ball bearing etc complete all specified and directed Note : Weight of aluminium sections for frames and shutters shall be only considered for payment. Cost of other consumables required for the item shall be deemed to be included in the quoted rate. However glass panes ? Bakelite sheet / wire cloth / mortice lock / locking stay / floor spring / floor door stopper only will be measured and paid separately under respective items as supply only and fixing by element of these items shall be deemed to be included in quoted rate.

Supply only 4mm thick figured glass / pin headed type ordinary quality fixed in aluminium ventilator complete all as specified and directed.

M&L for kota stone slab flooring 20-25mm thick including 20mm thick screed bed in cement morta 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing polishing complete all as specified and directed.

M&L kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar, in single piece, with round nosing with three numbers of separation as in treads of steps for staircase laid over 10mm thick CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade or the slab including rubbing and polishing complete all as specified and directed.

Supply only stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm, fixed in aluminium windows complete all as specified and directed.

S&F in repairs aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40 mm complete all as specified and directed,

S&F mild steel framed work such as grills, gratings etc, with ends of bars shouldered or rebated or forged into spikes, framed guard bars, barred iron doors, railings, frame work of water tanks and similar work conforming to Fe-290-Gde-E-165 complete all as specified and directed.

S&F stainless steel butt hinges, medium weight, 100mm long, complete all as specified and directed.

S&F aluminum anodised barrel tower bolts of extruded section, 150mm long (dia of bolt 12mm) , complete all as specified and directed.

S&F 300mm long aluminum anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding of extruded section complete all as specified and directed.

S&F aluminum anodised bow handles of 150mm size, fabricated type of extruded section fixed with screws to shutters, complete all as specified and directed.

M&L for providing 75mm thick PCC (1:3:6) type C-1 (using 20mm grades stone aggregate) as in plinth protection, surface finished even & smooth without using extra cement including provision of 10mm joints (at an interval of 3m and turnings) duly filled with fine sand and bitumen of grade 85/25 in the ration of 3:1 complete all as specified and directed.

S&F cast iron Nahani trap with grating incl jointing to waste pipe of 75mm dia in and including cement concrete type B1 (1:2:4) complete all as specified and directed.

Dismantling floor, hearth or wall tiling and stone slabs including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed.

M&L for coloured Non-skid ceramic tiles 7 to 8 mm thick (square / rectangular) of approved size, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 15mm thick cement mortal screed bed in CM 1:6 complete all as specified and directed.

M&L for coloured 300x200x7mm thick glazed ceramic tiles on vertical surfaces such as skirting, dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick cement mortar backing coat in CM 1:3 etc, complete all as specified and directed.

S&F in repairs, vitreous china, 1st quality, squatting pan (Orissa pattern), of size 580x440mm, white, with and including 'P' of 'S' trap, integral foot rests, lime concrete bedding including dismantling existing lime concrete bedding, unserviceable connections etc and connecting up, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed.

All as per item No 38.00 here-in-above but 20mm bore dia -ditto-

All as per item No 38.00 here-in-above but 25mm bore dia -ditto-

S&F for 15mm bore medium grade galvanized steel water tubing (ISI marked) with all fittings and fixed to wall / ceiling or laid in floor complete all as specified complete all as specified and directed.

All as per item No 41.00 here-in-above but 20mm dia -ditto-

All as per item No 41.00 here-in-above but 25mm dia -ditto-

S&F in repairs wash hand basin, vitreous china white of size 550X400mm excluding taps, waste chain and plug and porcelain stopper but including brackets, 32mm waste fitting and waste pipe of 32mm bore, brass, chromium plated for glazed ware wash basin complete all as specified and directed.

M&L for sunken floor treatment by roughening of sides and bottom of sunken floor by picking, sweeping clean and washing down with water to remove dust etc. and 10mm thick rendering in CM (1:4) on concrete surface (bottom sides of sunken floor) finished fair and even mixed with liquid water proofing compound conplast X 421 IC mfd by M/S FOSROC chemicals (India) Pvt Ltd, priming coat of "Nitro Proof 100" and after drying of primer applied one coat of "Nitro Proof 120" mfd by M/S FOSROC complete all as specified and directed.

S&F in repairs flushing cistern, 10 ltrs capacity, PVC valve less, symphonic action type with dual flushing system, low level white with inlet ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density PVC 32mm dia, complete all as specified and directed.

S&F stop valve, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, fancy type, chromium plate, with long shank and cup for iron pipe of 15mm bore, complete all as specified and directed.

S&F 15mm bore bib taps, cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S&F 15mm pillar tap cast copper alloy with capstan head chromium plated fancy type screwed down high pressure with or without letter hot or cold with long screwed shank and flynuts screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15mm size PVC connection with PTMT nuts 450mm length, complete all as specified and directed.

S&F in repairs brass chromium plated, shower rose, 125mm size, complete all as specified and directed.

S&F towel rail 600mm long of PTMT (Min weight 190 grams) fixed with and incl chromium plated brass screws and wooden / plastic cleats, complete all as specified and directed.

S&F 32mm bore high density polyethylene pipes (LDPE) of pressure rating 6 Kgf / Cm2, fixed to walls, ceiling or laid in floors etc complete all as specified and directed.

S&F machine cut cudappa stone slab 20-25mm thick over cement screed bed CM 1:4 10mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing as in cill / wall cladding etc complete all as specified and directed.

Taking down CI/PVC soil / waste and vent pipes of any length any size including fittings including cutting of holes wherever required complete all as specified and directed.

S&F 110 mm bore PVC (SWR) soil, waste and vent pipes single socketed in any length with rubber ring joints and PVC clamps with nuts & bolts fixed to walls complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) branch piece single (Single 'Y') equal or unequal with access door complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F 75mm bore PVC (SWR) soil, waste and vent pipes dingle socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F 75mm bore PVC (SWR) branch piece single (Single 'Y') equal or unequal with access door complete all as specified and directed.

S&F 75mm bore PVC (SWR) vent cowl complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

M&L for applying two coats of oil bound distemper over one coat of primer, after preparation of new surfaces of walls etc complete all as specified and directed.

M&L for complete removal of existing treatment of wall by booming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots including washing down with water etc applying two coats of oil bound distemper over one coat of primer, complete all as specified and directed.

M&L for preparation new wooden surfaces any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M&L for preparation old wooden surfaces of any description or not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation new plastered surface of walls and applying two coats of weather resistant acrylic emulsion paint over a coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment of old plastered / unplastered surface on walls chajjas, balcony, facias etc and applying two coats of weather resistant acrylic emulsion paint over a coat of primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coat of white wash, complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling and applying one coat of white wash, complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying two coats of white wash, complete all as specified and directed.

Roughening surfaces of existing roof treatment and taking out old APP membrane along with roof plaster and removing from site including cleaning and washing down with water to remove dust etc and brushing neat cement slurry @ 3Kg/Sqm complete all as specified and directed by engr-in-Charge.

M&L fir 10mm thick screed bed or bedding layer of mortar in CM 1:4 as in roof padding, finishes, surface even and smooth without using extra cement with WPC as per manufacturer instructions, complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L for lying and providing of water proofing treatment or RCC roof are as under following :- (a) The dried surface of slab shall be painted with one coat of bituminous primer @ 0.4 liter/sqm conforming to IS-3384 (b) Over the primed surface a layer of APP based polymeric membrane of approved manufacturer 3mm thick, reinforced with polyester non woven fabric (weighting not less than 160 gms / sqm shall be laid by torch application method. The side over laps of membrane shall be minimum 75fmm and the end laps shall be minimum 100mm and sealing all overlaps and joints shall be done as per manufacturer's instruction. (c) The finished surface shall be given one coat of Aluminum paint @ 0.11 Kg/sqm on top of APP for heat resisting as per manufacturer instruction. complete all as specified and directed.

Taking down shutter for easing and adjusting and refixing in same opening area exc 1.00 sqm and n.exc 2.00 sqm each complete all as specified and directed.

M&L fir 25mm thick cement concrete 1:2:4 type B0 (using 12.50mm graded crushed stone aggregate) as in leveling course / sub floor finished even and rough to receive floor finishes complete all as specified and directed.

M&L Glass dividing strips, 38mm width and 3mm thick and ditto complete all as specified and directed.

M&Lfor PCC (1:2:4) type B0, using 12.5mm grades stone aggregate as in chajjas to achieve required slope including making rounded chamfered on edges mixed with WPCas per manufacturer's instruction , complete all as specified and directed. Note : WPC shall measured and paid separately as supply only.

M&L precast reinforced cement concrete 1:1 1/2:3 type A-1 (using 20mm grade stone aggregates) as in cover slabs, shelves and the like including weathering, slightly rounded or chamfered angles and throating, also including use and waste of form work, complete all as specified and directed. Note : Reinforcement shall be measured and paid separately.

M&L for mild steel TMT bars 8mm dia, and over, up to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks 500 ltr capacity multi layer (Cylindrical vertical with closed top) (ISI marked) hoisted and fixed in position including provision of necessary fittings for connection the overflow, drain out, inlet and outlet pipes, complete all as specified and as directed.

S&F ball brass valves of size 20mm bore (ISI marked) high pressure, the polythene float and fly nut, screwed for iron pipe or brass frame et, complete all as specified and directed.

S&F anodised aluminum alloy curtain rails 20mm dia chromium plated, with and including fixing brackets, stops, rollers etc, complete all as specified and directed.

S&F in repair 25mm bore gun metal globe or gate valves (ISI marked) with iron wheel head, screwed both ends for iron pipes, complete all as specified and directed.

S&F sinks made of stainless steel 1mm thick, kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including provision of fixing cantilever brackets and connecting union to pipe, also including 40mm bore PVC waste pipe, overall size 495mm X 420mm with bowl size 410mm X 330mm X 160mm complete all as specified and directed.

Dismantling Asbestos cement / galvalume aluminium zinc (corrugated semi corrugated, etc) sheets in roof coverings etc complete all as specified and directed.

S&F pre painted galvalume zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550mpa as in roof covering / cladding to wall, fixed with self taping screws complete all as specified and directed.

S&F pre painted galvalume zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550mpa as in roof covering / clading to wall, fixed with self taping screws complete all as specified and directed.

M&L 75mm thick cement concrete 1:4:8 (type D-2) (using 40mm graded stone aggregate) as in sub base, finished even and fair to achieve the topping layer of tiles, complete all as specified and directed.

M&L for chequered cement concrete tiles 30cmX30cmX25mm thick (with grey cement and pigments) set joined and pointed in neat cement slurry in floor with grey cement mixed with pigments to match with the colour of tiles, laid over and including 20mm thick screed bed in CM 1:4 complete all as specified and directed.

Roughening surfaces of old concrete floor by picking sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3 kg of cement per sqm complete all as specified and directed.

M&L 20mm thick granite slabs of any type (table rubbed and polished) on cooking platforms set and jointed in net cement slurry and pointing in white cement (1:2) using marble dust with admixture of pigment to match shade of granite including necessary moulding at edges laid over and including 10mm thick cement mortor screed bed in cement mortor (1:3) complete all as specified and directed.

S&F anodised aluminium snap grid frame work size 605X605mm for false ceiling complete all as specified and directed.

M&L for 4mm thick non asbestos fibre cement building designer board fixed or laid / inserted to triber / GI / aluminium frame fixed in ceiling complete all as specified and directed.

Dismantling boarding any description fixed in any position with nails and removing from site complete all as specified and directed.

M&L 18/19mm thick preliminateed partical board exterior grade BWR type fixed with screws to timber frame work as in cup board shelves etc complete all as specified and directed.

M&L for Hasp and staple, safety type, aluminium anodised 100mm including bolt to hinge plate and fixed with screws complete all as specified and directed.

Re-writing letters or figures (Block, roman, Italic or Indian) n. exc 30cm height with synthetic enamel paint complete all as specified and directed.

S&F in repairs stainless steel butt hinges, medium weight multi-layered, 100mm long complete all as specified and directed.

Supply and fixing rotational moulded polyethylene water storage tanks, double layered (ISI Marked) of 2000 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position , including provision of necessary fittings for connecting the overflow, drain out, inlet and outlet pipes, complete all as specified and as directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation etc and getting out in soft loose soil complete all as specified and directed.

Surface dressing n.exc 15cm deep in soft/loose soil including removing of bushes complete all as directed

M&L PCC 1:4:8 type D2 using 40mm graded aggregate as in foundation filling and mass concrete complete all as specified and directed.

Returning filling in including spreading leveling watering and well ramming in layers n exc 25 cmin soft/loose soil complete all as specified and directed.

Removing excavated material n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point complete all as specified and directed.

M/L for brickwork, old size with fly ash bricks straight or curved on plan exc 6 m mean radius, built in CM1:6 complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coats of cement base paint over one coat of primer on wall etc complete all as specified and directed.

M&L for three coats of white wash as in new plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M/L for RCC M-25 Desogn Mixas in Lintel and slabs all as specified and directed.

M&L for formwork to Beams/Lintels and similar items including edges for flat rough finished surface of concrete complete all as specified and directed.

S/F 10mm dia and over TMT bar cut to length bent to shape required including cranking, bending and binding with M.S wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and as directed.

.M&L TMT bars 5mm dia and over upto and incl 10mm dia in stirrups cut to length, bent to shape required including cranking bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

Hardcore of gauge not exc. 63mm, deposited, spread and leveling in layers not exc. 15 cm thick, watered and rammed to true surface with broken stone or boulder complete all as specified and directed.

M/Lfor PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) for damp proof course,40 mm thick to horizontal or vertical surfaces including necessary formwork and mixed with WPC as per manufacturer's instruction complete all as specified and directed. Note : WPC will be measured and paid separately)

M&L for 20 mm thick screed bed or bedding layers for floor tiles etc in cement mortar 1:6 complete all as specified and as directed.

M&L for 10mm thick rendering in cement mortar 1:3 for laying vertical tiles complete all as specified and as directed.

M&L for Non Skid ceramic tiles 7 to 8 mm thick, coloured (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed complete all as specified and directed.

M&L for glazed coloured ceramic tiles of size (450mm x 300mm ) X 7 to 8mm thickness in floor set and jointed in neat cement slurry and pointed the tiles complete all as specified and as directed

S&F steel work in tubular trusses/ posts including special shaped washer etc. complete using ERW or induction buttwelded tubes confirming to IS 1161-1979 grade St-240complete all as specified and directed.

S&F of Steel ventilator with top hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F 3mm thick figured glass pin head type and glazing with oil putty in squares not exceeding 0.50 sqm in each pane complete all as specified and as directed.

S&F PVC valve less, syphonic action type , flushing cistern, low level, white with inlet ball valve float and handle including bracket complete all as specified and directed.

S&F vitreous china wash hand basin white colour flat back of size 550x400mm including pedestrial including CI brackets, CP brass waste coupling 32mm and waste pipe 32 mm etc complete all as specified.

S&F PVC (SWR) 110 mm bore pipes single socketed in any length with rubber ring joints incl PVC clamp with nut and bolts laid in trenches or in floor complete all as specified and directed.

S&F for PVC (SWR) 110mm Junction (single T) equal or un equal provided with access door complete all as specified and directed.

S&F PVC connection pipe 15mm dia 450 mm long complete all as specified and directed.

S & F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock, strick plate, etc complete as specified, supplied and fixed. of frame 105x 60 mmand thicknes of profile 1.25mm complete all as specified and directed.

S & F Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides ,30 mm thick complete all as specified and directed.

S&F for aluminum anodized barrel tower bolts of extruded section 200mm long, ISI marked (dia of bolt 12mm) , complete all as specified.

M&L of Providing cement concrete filling in pressed steel frame and other similar bands, plinth courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, appex 1:3:6 type C-1 ( 20 mm graded aggregates)stones, bed plates complete all as specified and as directred.

M&L for Salt-glazed stoneware drain pipes gradr 'A' laid in trenches and jointed with cement joint for 150 mm dia all as specified and directed.

M&L for cement Concrete bed (1:3:6) type C2 to drain pipes 150 mm dia including packing under, and haunching against the sides of pipes after they are laid and tested all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth ) complete all as specified and directed.

M&L for PVC (SWR) floor trap plain with grating including jointing with solvent cement, dia of out let 63mm complete all as specified and directed.

S&F waste coupling of PTMT (half or full threaded) Minimum weight 32mm-45gms complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) (ISI marked) hoisted and fixed in position all as specified in SSR Part I - Capacity 1000 Litre complete all as specified and directed.

M&L for Gun-metal, globeor gate valves (ISI marked) , with iron wheel head, screwed both ends for iron pipe and fixed for 20 mm complete all as specified and directed.

S&F PVC (SWR), junction single, (Single T) equal or unequal,110mm complete all as specified and directed.

M&L for 100 mm thick PCC 1:4:8 type D-2 (using 40 mm graded mechanically crushed stone aggregate) as in sub base to floor, complete all as specified.

M&L for RCC M-25 Design MixFoundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L for 40mm thick Cement concrete as in floor type B-1, 1:2:4 (20mm graded aggregate) finished the surface even and smooth without using extra cement complete all as specified and directed

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in surface channels and drains copmlete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped end etc complete all as specified and directed.

S&F galvanised corrugated mild steel sheeting 0.63mm thick with zinc coating 120sqm / sqm with two corrugations side lap fixed with "L" type or "J' type or cranked hook bolts and washers in roofs complete all as specified.

Hacking out old broken glasses ( any thickness/type and in any position ) from wooden frames/metal frames fixed with oil putty or beads etc and removing from site all as spd complete all as specified and directed.

M&L preparing old steel surfaces of any description exc 10cm width or girth and applying one coats of synthetic enamel paint complete all as spd and directed

Preparing old zinc (or galvanised) steel surfaces to receive painting ,by using mordant solution including washing and cleaning,etc complete all as specified and directed.

M&L for applying two coats of coptic green paint over a coat of red oxide zinc chrome primer over steel surfaces complete all as specified and directed.

Repair of manually operated sliding steel door of hangars of approximate size 4.20 m x 6.00 m including replacement of damaged ball bearings of top wheels (02 nos ), bottom wheels (02 nos) ,side wheels of track ,bearings of chain pully etc complete including necessary cutting, welding bolting and making rail good to match with adjoining surface, masonary work including taking down and refixing of door by mechanical lifting by means of crane and necessary greasing for smooth functioning of door complete all as directed.

Racking out existing filling in expansion joints, construction joints,15 mm wide dummy joints upto 30 mm depth including scrubbing of joints with diamond cutter machine(Heavy duty) to remove sticking sealing compound from the sides and top of joints and totally cleaning the top surface of joints with brush and finally fanning with compressed air to make the joints free from all loose materials ie dirt/dust etc to entire satisfaction of Engr-in-Charge, applying with provision of bond breaker tape on bottom of joint and filling depth of joint with provision of polyethylene back up rod of suitable dia to ensure tight packing so that no gap or voides exist at the top of backer rod. The deteriorated edges of concrete joints (included upto 50mm either sides of the joints) shall be made good to true line with provision of polymer concrete. Joints (10mm to 15mm wide) shall be sealed with provision of polyethylene base sealant using Rallithane/Colpor-200of M/S Fosroc chemical (India) Pvt Ltd/Seal N Flex FC polyethylene joint sealant manufurered by BOSTIK INDIA PVT LTD and with primer N-49 and filling the joints with Polyurethane based sealing compound as laid down in manufacturers instructions and as directed by Engr-in-Charge. Minimum clear depth of sealant above back up Rod shall be 10mm complete all as specified and as directed. NOTES:-(i) Size of joints shall be made by cutting in case not available at site. (ii) If width of joints by cutting exceeds as specified above, the same shall be filled by polyethylene based sealant and no extra payment shall be made. (iii) Remaining depth at bottom (after keeping provision for back up Rod & sealant) shall be filled with sand and cost of same shall be deemed included in item rate quoted by tenderer. No extra payment for provisioning of sand(if any) shall be made. (iv) Marking tape shall be applied on edges of joint to prevent accidental slippage of sealant and shall be removed after filling with sealant. Cost of the same shall be deemed included in item rate quoted by tenderer. (v) Make of sealant shall be Rallithane/Colpor-200of M/S Fosroc chemical (India) Pvt Ltd/Seal N Flex FC polyethylene joint sealant manufurered by BOSTIK INDIA PVT LTD and with primer N-49 as laid down in manufacturers instructions including marking tape 40mm wide on both edges joint before filling the joint and removing the tape immediately after applying sealant, or equivalent as approved by Accepting Officer complete all as specified and directed.

M&L for painting lines, dashes arrows ,letter etc on road pavements etc nexc. 10cm width with road marking paint white or golden yellow including preparation , complete all as spd and directed

M&L for painting lines, dashes arrows ,letter etc on road pavements etc exc. 10cm width with road marking paint white or golden yellow including preparation , complete all as spd and directed

M&L for for septic tank for 25 Users complete all as specified and shown on drawing)

M&L for soak well 1.20m dia and 3.00m deep complete all as specified and shown on drawing.

M&L for RCC M25 (Design mix) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick rough finished surface(Horizontal or sloping for flat complete all as specified and directed.

S&F mild steel bars TMT 6mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for coh, .nuns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conferming to complete all as specified and directed.

Loose filling with broken stone or boulders aggregates of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified and directed.

S&F CI manhole cover 600 mm Dia complete all as specified and directed.

Taking down carefully old unserviceable copper/aluminium point wiring (light,Exchaust fan, socket or power) complete incl fittings such as switches, ceiling roses, pendents, regulators,bells,sockets,tube light fittings etc, and making good disturbed surface of walls & floors etc complete all as specified and as directed.

Taking down old unserviceable Main Switch, DB's consisting of MCBs wooden/GI/MS sheet board etc for kept in store and for later use all as directed.

Taking down carefully unserviceable sub main wiring of any size/core/type including making good the disturbed surfaces all as directed.

M&L for concealed point wiring with two single core PVC insulated, unsheathed, multistranded copper conductor FRLS of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.50 sqmm green in colour as earth lead in and including PVC rigid conduit (medium grade) with all fittings & accessories including provn of MS sunk terminal box of appropriate size suitable for switch fixed flush to wall for mounting switch, sockets, fan regulators etc with 3mm thick hylum sheet top cover with screws & cup washers for one light / fan point / call bell complete. NOTE : Cost of making good the disturbed surfaces (if any) matching with the existing surface and cutting chases are deemed to be included in the unit quoted rates

All as per Item Sl No - 168.00 here in before but with two single core PVC insulated, unsheathed, multistranded copper conductor of size 2.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 2.5 sqmm green in colour as earth lead for 5/6 A switch-socket point on independent board complete. complete all as specified and directed.

All as per Item Sl No - 168.00 here in before but with two single core PVC insulated, unsheathed, multistranded copper conductor of size 4.00 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 4.00 sqmm green in colour as earth lead for 15/16 A switch-socket point on independent board complete. complete all as specified and directed.

All as per Item Sl No - 168.00 here in before but with two single core PVC insulated, unsheathed, multistranded copper conductor of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.5 sqmm green in colour as earth lead for 5/6 A socket point with switch on same board complete. complete all as specified and directed.

M & L for Switch Socket combination 3 Pin, 5 Amp flush type universal, 240 volts, complete as directed.

M & L for Socket outlet 3 Pin, 5 Amp flush type universal, 240 volts, complete as directed.

M & L for Switch Socket Combination 5 in 1, 3 pin, 5 and 15 Amp flush type universal, 240 volts, complete as directed.

S&F piano switch single pole 5 Amp 230 Volt all as specified and as directed.

S&F ceiling rose ,surface bakelite 65mm x 50mm size with three terminals all specified and as directed.

S & F Bell Push Flush type 5 Amp, 240 volt all as specified

S & F Bell Ding-Dong AC 230 V Single Pole complete as directed.

Taking down existing u/s FTL light fitting and S&F decorative box type fitting with LED retrofit tube 21 watt with Al extruded batten luminaire for 230 volt AC,including LED tube 21 Watt complete all as specified and directed by EIC Make ;Philips Cat Ref-BN021CLED20SPSUCWGRS2 or equivalent model complete.

M&L LED street light of capacity 8 watt in Aluminium PDC housing, toughened glass cover with IP66 protection complete all accessories with connections PVC copper wire not exc 5 mtr complete all as specified and directed.

Taking down existing u/s FTL light fitting and S&F decorative box type fitting with LED retrifit tube 10 watt 2 feet with Al extruded batten luminaire for 230 volt AC,including LED tube 10 Watt complete all as specified and directed.

Taking down ceiling fans of any size, sealing cable end,dismantling blades and removing complete all as specified and directed.

S&F electronic step regulator (speed regulation in 5 steps) suitable for ceiling fan 1200 sweep/1400 mm, 120 Watt complete all as specified and directed.

S&F energy efficient, star rated ceiling fan 230V 1200 mm sweep with all accessories and connecting up with the ceiling rose with required flexible wire of suitable size with ceiling fan complete all as specified and as directed.

S&F in repair exhaust fan AC, single phase, 230/240 V, of size 300 mm seep steel/aluminium metal body incl making holes on wall & making good the disturbed surfaces with all connecting arrangements complete all as specified and directed.

Supply & Fixing DB with sheet metal enclosure 240 volts, 8 way with 200 Amp rated bus bar single pole & neutral double door for MCB, incl cutting chases for DB of reqd size and making good disturbed surface area complete all as specified and as directed.

Supply & Fixing MCB double pole (DP) 240 volts of capacity 06-32 Amp ,C curve, complete all as specified and as directed.

S&F MCB, SP, 10KA, 415V, "C" curve, 06-32 A, ISI Marked complete Cat No. 4086 28-36 of complete all as specified and directed.

Supply & Fixing TP&N DB 4 way with sheet metal enclosure 415 volts, double door 200 Amp rated bus bar for MCB incl cutting chases exc 10 cm but not exc 20 cm girth for DB and making good disturbed surface area complete all as specified and as directed.

S&F MCCB 63Amp four pole 415 volt breaking capacity 16KA adjustable thermal and adjustable magnetic complete all as specified and directed.

Material and labour for concealed sub main wiring surface type with two nos single core PVC insulated unsheathed multi strand copper conductor FRLS cable of size 6 sqmm and one no single core PVC insulated unsheathed multi strand copper conductor FRLS cable of size 6 sqmm as in continuous earth wire drawn into and including 25mm dia rigid non-metallic ISI marked PVC conduit medium grade with all fittings and fixings accessories complete all as specified and as directed. Note : (i) Cutting chases shall be measured and paid separetely. (ii) Two run of submain wiring cable alongwith are run of earth wire shall be measured as one length.

Taking down existing u/s highbay hanger light and S&F maxolid highbay light fitting with protection IP 65 with circular form factor with thoghened glass of 210W. Luminaire housing made of high pressure die cast aluminium 230 volt AC complete all as specified and directed.

Supplying & fixing indoor decorative aluminium extruded T5 LED batten incl LED tube rod of cap 20 watt, 4 (feet) integrated type incl connections with 2 core flexible copper wire 0.50 sqmm from ceiling rose light fittings fitted on PVC round / square box complete all as specified and as directed.

Supply, laying, jointing and testing in trenches or passing through pipe 1100 volt grade, XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured LT electric power UG cable heavy duty with stranded aluminium conductor of cross-section area 25sqmm 3.50 core witrh all fixing and connecting accessories such as aluminium cable lugs, cable glands nbut, bolt, washer etc complete all as specified and as directed. (Note : (i) Earth work and excavation GI pipe etc shall be required and paid separately. (ii) Specification of cable are as under :- (a) Inner sheathing shall be extruded PVC. (b) Cable shall be supplied with sequences hall marking at every metre on the inner sheeting. (c) Ultra violet radiation resistance compound comprissing to ASRM-2863 flame retarded as per EIV specification. (d) Anti roddent and antitermite compound added. (e) PVC compound of various grade as IS-5831. (f) Compaction conductors shall be shaped and arrangement to the same will be onthe cable.

S&F decorative box type fitting with LED retrifit tube 21 watt with AI extruded batten luminaire for 230 volt AC, including LED tube 21 watt complete all as specified and directed by Engr-in-Charge

S&F energy efficient, 5 star rated ceiling fan 230V 1200mm sweep with all accessories and connecting up with the ceiling rose with required flexible wire of suitable size with ceiling fan complete all as specified and directed.

S&F DB with sheet metal enclosure 240 volts, 4 way with 200 Amp rated bus bar single pole & neutral double door for MCB incl cutting chases for DB of reqd size and making good disturbed surface area complete all as specified and as directed.

All as per item No 194.00 here-in-before but for 10 sqmm 2 cdore -ditto-

S&F GI pipe 40mm light grade (ISI marked) for cable protection complete all as specified and directed.

Supply and laying in trenches dry river sand for cushioning under cable with a layer of 8 cm below and 15 cm above cable complete in level all as specified and directed by Engr-in-charge

Supply and laying burnt clay sub class B brick best quality locally available as cable protection all as specified and directed.

M & L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground (in vertical position ) earth pit not less than 2.25 mtrs below normal ground level with the top edge of the earth plate not less than 1.5 mtr (B.G.L.) & connected to galvanised iron wire 4 mm dia by means of bolts,nuts,checknuts & washer of galvanised iron including PCC (1:2:4) type B1 precast RCC cover slab with suitable handle made pf 6 mm round bar, including necessary excavation & earth work in any type of soil , 20 mm dia med grade galavinised steel tube for watering with one end fixed with cast iron funnel & wire mesh, 15 mm bore light grade galvanised steel tubing up to 7.5 mtr length for drawing earth lead GI strip protection & common salt , charcoal in alternate layers etc. complete all as shown in EP no 3 of SSR Part 1 & testing on completion incl taking down old unsv earthing complete all as specified and directed.

M&L for drilling of trial bore of 250 mm dia upto140 mtr depth below ground level in any kind of soil strata incl hard stone/ boulder by deploying reverse rottary process etc including cost of consumable stores like fuel lubricants, bentonite mud, material and transportation of rigs machinery etc. and supply of strata chart and all other desired information etc. complete all as specified and directed. (For two bore well). NOTE:- Errection and dismantling of boring plant including all arrangement for the transportation of the boring equipment to site of work from the store of contractor at site and back are to be made by the contractor at his own cost. All rates should be quoted for supplying the material at site of work.Pits for collection of water and water for drilling tube well be arranged by the firm / contractor at site at his own cost. complete all as specified and directed.

M&L for development of trial bore by reaming up to 550 mm dia from ground level upto and including a depth of 60 mtrs in step from ground level complete all as specified and directed. (For two bore well). NOTE :- Development of trial bore should be done by reaming in following step:- (a) From 250mm to 350 mm (b) From 350mm to 450 mm (c) From 450mm to 550 mm

M&L for development of trial bore by reaming up to 450mm dia from depth exceeding 60 mtrs and up to 140 mtr depth complete all as specified and directed. (For two bore well). NOTE :- Development of trial bore should be done by reaming in following step:- (a) From 250mm to 350 mm (b) From 350mm to 450 mm

M&L for electric logging in pilot bore for precise delineation of granular zones as also the quality of ground water including report interpretation complete all as specified and directed. (For two bore well). NOTE:-Electric logging shall be carried out by any approved reputed agency.

Supply, fixing & lowering in bore well 250mm bore ERW/ MS casing pipe electric resistant welded pipe with sockets (housing pipe) confirming to IS:4270-1992 (with upto date amendments) duly ISI marked and approved by Engineer-in-Charge. The housing pipe shall be of suitable length as per the site requirements manufactured out of 8.00 mm thick MS plate including the cost of required number of sockets of size 177.80 mm width made out of 1/2 “ (12mm thick) plate including painting with two coats of anti corrosive bituminous paint of approved brand etc (For Two Borewell) complete all as specified and directed.

Supply, fixing & lowering in bore well 200mm bore ERW/ MS casing pipe electric resistant welded pipes with sockets (housing pipe) confirming to IS:4270-1992 (with upto date amendments) duly ISI marked and approved by GE. The blind pipe shall be of standard length as per the site requirements with 76.02 mm of threaded end (8 threads to an inch or 25.4 mm) manufactured out of 8.00 mm thick MS plate including the cost of required number of sockets of size 152.4 mm width made out of 1/2 “ (12mm thick) plate including painting with two coats of anti corrosive bituminous paint of approved brand etc (For Two Borewell) complete all as specified and directed.

Supply lowering and fixing / jointing 250mm bore low carbon galvanized (LCG) strainer 3 mtr / 6 mtr long min 6mm thickness each conforming to IS-8110 2000 including mild steel socket threaded by electic arc welding both sides complete all as specified and as directed with aperture 0.75 mm to 1.00 mm as per requirement (Make Johnson screen/manufacturer with BIS Licence (For Two Borewell) complete all as specified and directed.

Supply lowering and fixing /jointing 200 mm bore low carbon galvanised (LCG) strainer 3 mtr / 6 mtr long min 6 mm thickness each confirming to IS 8110 2000 including mild stell socket threaded by electric arc welding both sides complete all as specified and as directed with aperture 0.75 mm to 1.00 mm as per requirement (Make Johnson screen/manufacturer with BIS Licence (For Two Borewell) complete all as specified and directed.

Development of tube well with compressed air and after with 25% extra capacity pump by pumping muddy water of bore well using air compressor of 350 psi, 600 cfm air pressure for required number of hrs including fuel etc (For Two Borewell) complete all as specified and directed.

Yield test for the bore well by continuously pumping for 16 hours to determine safe pumping yield (For Two Borewell) complete all as specified and directed.

Dismantling of old submersible pump with old column pipe and lowering of same pump with new clolumn pipe at new bore well (For Two Borewell) complete all as specified and directed. Note :- New column pipe will be measured and paid separately under respective item.

S&F MS column pipe flange type including jointing materials (ERW) Steel nominal dia 100mm as per IS 3589 (1981) thickness 4.8mm including necessary welding of pipe & flange in two sides with MS flat iron of suitable length and size including painting with two coats of anti corrosive bitumastic paint of approved brand etc (For Two Borewell) complete all as specified and directed.

S&F valves, sluice, flanged of class PN 1.6, 150mm (6") dia complete all as specified and directed.

S&F valves, butterfly conforming to IS 13095, 100mm dia complete all as specified and directed.

Supply only strata sample box with glass cover 3mm thick having internal dimension 1000x600x100mm made out of 20mm thick wought 1st class hard wood shisham with hinges hasp and staple including polishing complete with samples at various depth evenly 2mtr interval met in boring including strata chart in duplicate (For Two Borewell) complete all as dirceted and specified.

Supply & filling pea gravel of 10mm to 30mm size around the casing pipe of bore well including all leads and lifts should pea gravel free from dust, dirt or vegetable manure complete all as specified and directed.

Supply, laying, connecting and testing cable PVC insulated (heavy duty) 1100 volts grade, with copper conductor of size 3 core, 6 Sqmm submersible cable (For Two Borewell) complete all as specified and directed.

S&F in replacement including lowering of steel wire rope, PVC insulated of size 12mm dia of suitable size/length as directed with clamps nuts & bolts and washers etc for holding column pipes/GI pipes of submersible pump set (For Two Borewell) complete all as specified and directed.

S&F MS reducer socket of size 10" x 8" pipe to be fabricated out of 12 mm sheet plate with the housing pipe 10” of approved quality for fixing 10” dia MS pipe with 8” MS pipe (For Two Borewell) complete all as specified

S&F MS threaded well cap with locking arrangement of approved quality for 10" dia MS pipe complete all as specified and directed.

M&L for bail plug of approved quality for 8" dia MS bore pipe complete all as specified and directed.

S&F MS centre guide of approved quality for 8" dia MS bore pipe complete all as specified and directed.

Supply and installation of MS fabricated factory made catalytic media chamber of size 1000mm dia, 1200mm height and 8 mm thick required for existing 8000 GPH pressure cum iron removal plant including full load of catalytic media back washing facility including RCC nominal mix (1:2:4) type B-1 using 20mm graded stone aggregate foundation, reinforced with of 10mm dia TMT bar @ 150mm C/C both ways with and inclusive necessary form work complete all as specified and directed.

Removal of filter media complete from mild steel shall of iron removal plant including PVC strainer of 8000 GPH for replacement of gravels sand and MN02 and disposal of unserviceable materials to a distance not exec 50 meter completed all as specified and directed

Scraping, de-scaling cleaning internal surfaces of mild steel shall and applying two coats of approved grade paints for drinking water and providing one coat of painting on external surface of steel alongwith pipeline with anticorrosive over a coat of red oxide /zinc chrome primer with necessary preparation of surfaces completed all as specified and directed

Supply and incorporation of MN02 of size 1/8" x 1/10" as filter media of iron removal of plant complete all as specified and directed.

Supply and incorporation of GRAVEL of size 1-1/4" x 1-1/2" (collection source BARAKAR river bank) as filer media of iron removal plant complete all as specified and directed.

All as per item No 229.00 here-in-before but size 1/2" x 1" -ditto-. complete all as specified and directed.

All as per item No 229.00 here-in-before but size 1/4" x 1/2" -ditto-.complete all as specified and directed.

Supply and incorporation of SAND of size 1/6" x 1/8" mesh (colletion source BARAKAR river bank) as filter media of iron removal plant complete all as specified and directed.

Supply and incorporation of Anthracite grit of sixe 1/8" x 1/4" as filter media of iron removal plant complete all as specified and directed.

S&F strainer of sizes as dismantled complete all as specified and directed.

S&F Air compressor of 700 RPM Single stage double cylinder with working pressure 171 PSI of 5.0 HP with 14.5 CFM running motor having 220 Litre tank capacity including 15mm bore MS/GI air line as required complete all as specified and directed. Make : ELGI, Ingersoll Rand or equivalent model of make as approved by the GE.

Testing of water sample of new boring for bacteriological and chemical testing (systematic analysis) from government approved laboratory including submitting the report to the department (For Two Borewell) complete all as specified and directed.

Supply, laying and testing Ductile iron pipes 150mm dia, class K-9 S/S including joint, laid in trenches or under floors complete all as specified and directed.

M&L including jointing and testing Ductile iron fitting such as bends taper, tee pieces (single or double branch) any type and angle/radious and straight connecting pieces but all end flanged suitable for 200 mm bore of pipe. complete all as specified and directed.

M&L preparing old painted CGI sheet of any description exc 10cm width or girth and applying one coat of coptic green paint complete all as specified and directed.