SPECIAL REPAIRS TO GANGA HOSTEL A, B, C BLOCKS AND KALAM DINING BLOCK AT DIAT, GIRINAGAR, PUNE

Dismantling tile work in floors, walls and roofs for thickness of tiles 10 mm to 25 mm laid in cement mortar including stacking material within 50 metres lead complete all as specified and directed.

Demolishing cement concrete Nominal concrete 1:3:6 or richer mix (including equivalent design mix) manually/ by mechanical means including disposal of material within 50 metres lead complete all as specified and directed.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth complete all as specified and directed.

Demolishing brick work built in cement mortor manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead complete all as specified and directed.

Providing and laying Vitrified tiles in floor, of Size of Tile 600 x 600 mm (thickness to be as specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily complete all as specified and directed.

Providing and laying Vitrified tiles of size 600x 600mm, tile thickness to be as specified by manufacturer, with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc.complete all as specified and directed.

Providing and laying Anti Skid tiles in floor of Size of Tile 400 x 400 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily complete all as specified and directed.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete all as specified and directed.

Demolishing cement concrete nominal concrete 1:4:8 or leaner mix (including equivalent design mix) manually/ by mechanical means including disposal of material within 50 metres lead complete all as specified and directed.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, pliers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing 1:5:10 (1 cement: 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mmnominal size derived from natural sources) complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in sub base of floor finishes complete all as specified and directed.

M & L for Application of ZMB 60/ equivalent solution ( 100 Kg ZMB 60/equivalent 1 litre ZMB Nano Thinner& 20 litre water & 1 Litre Zycoprime/equivalent =122 litre/KG) over already applied coat of Zycosil/equivalent & Zycoprime/ equivalent solution on the top of all the RCC plinth beams by brush/spray coat before erection of GFRG panel over RCC plinth beams in GF. In the case of upper floors 150 mm wide on floor slab for all the external walls, bath/ toilet/wet areas (3 hrs drying time) before erection of wall panel on upper floors including erection of parapet wall complete all as specified and directed.

M & L for 25 mm thick Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 :4 (1 cement:4 coarse sand) complete all as specified and directed.

M & L for Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement:3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete all as specified and directed.

Extra for Kota stone/ sand stone in treads of steps and risers using single length above normal size up to 2.00 metre complete all as specified and directed.

Dismantling doors, windows and clerestory windows (steel, aluminium or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead of area 3 sqm and below complete all as specified and directed.

Taking out doors, windows and clerestory window shutters (steel, aluminium or wood) including stacking within 50 metres lead : Of area 3 sq. metres and below complete all as specified and directed.

S&F factory made pressed steel frames made out from 1.25mm thick steel sheet for doors of size 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.and including treated with tar or coal tar black paint on steel surfaces in contact / embeded in concrete or masonary work complete all as specified and directed.

S&F factory made pressed steel frames made out from 1.25mm thick steel sheet for doors of size 105x60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.and including treated with tar or coal tar black paint on steel surfaces in contact / embeded in concrete or masonary work including Filling hollow portion of frame complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in door frame filling and similar work filling complete all as specified and directed.

Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & Jointed with self driven self tapping screws of size 38 mm x 4 mm & PVC solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturer's specification complete all as specified and directed.

Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1 mm, painted with primer, all four corners of reinforcement to be welded orsealed. Solid PVC extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100 mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8 mm complete as per manufacturer's specifications complete all as specified and directed.

Providing and fixing wire gauge 35 mm thick shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws shutters with ISI marked M.S. pressed butt hinges bright finished of required size Kiln seasoned and chemically treated hollock wood complete all as specified and directed.

Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), fixing with butt hinges of required size with necessary screws, all complete as per directions of Engineer- in-charge and panelling with panels of : (Note:- Butt hinges and necessary screws shall be paid separately) 12 mm thick plain grade-1, medium density flat pressed three layer article board FPT - I or graded wood particle board FPT- I, IS : 3087 marked, bonded with BWP type synthetic resin adhesive as per IS : 848 complete all as specified and directed.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete Size : 300x16 mm complete all as specified and directed.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :Size 200x10 mm complete all as specified and directed.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :Size 125 mm complete all as specified and directed.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper complete all as specified and directed.

S&F in repairs 25mm bore stainless steel 304 grade curtain rods with suitable fancy type brackets and fixed in position using stainless steel screws complete all as specified and directed.

Providing and fixing 90mm bright finished brass hasp and staple (safety type) with necessary screws etc., complete all as specified and directed.

Providing and fixing bright finished brass helical door spring superior quality complete all as specified and directed.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture on wooden surfaces complete all as specified and directed.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture on steel surfaces complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails thickness 10mm and upto 25mm complete all as specified and directed.

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete all as specified and directed. Note: Payment of providing and fixing auto closing hinges shall be paid separately.

Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws complete all as specified and directed.

Providing and fixing special quality bright finished brass cupboard or ward robe locks 50 mm with four levers of approved quality including necessary screws etc. complete all as specified and directed.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete all as specified and directed.

Taking down exisiting vitreous wash basin of any size in repairs complete all as specified and directed.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Wash basin size 550x400 mmwith a pair of 15 mm C.P. brass pillar taps complete all as specified and directed.

Taking down exisiting UNSV Stainless steel sink of any size in repairs complete all as specified and directed.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink with drainage board as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required 510x1040 mm bowl depth 250 mm complete all as specified and directed.

Dismantling W.C. Pan of all sizes including disposal of dismantled materials including malba complete all as specified and directed.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid complete all as specified and directed.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete all as specified and directed.

S&F in repair 15mm bore two way bib cock with inlet and outlet screwed for pipe and connections including necessary fittings complete all as specified and directed.

S&F in repair 15mm bore heathfaucet with inlet and outlet screwed for pipe and connections including necessary fittings complete all as specified and directed.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests complete all as specified and directed.

Providing and fixing C.P. brass angle valve for basin mixer, flush tank and geyser points of approved quality conforming to IS:8931: 15mm nominal bore complete all as specified and directed.

Providing and fixing in repair Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed of approved quality conforming to IS:8931: 15mm nominal bore complete all as specified and directed.

Providing and fixing uplasticised PVC connection pipe, 15 mm nominal bore, with brass unions :45 cm length complete all as specified and directed.

Providing and fixing toilet paper holder : C.P. brass complete all as specified and directed.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings,standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern complete all as specified and directed.

Providing and fixing PTMT grating of approved quality and colour of rectangular type with openable circular lid complete all as specified and directed.

Providing and fixing PTMT grating 125mm nominal of approved quality and colour of circular type with 25mm waste hole complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections including cleaning for refixing with all fittings complete all as specified and directed.

All as per item no 59 here in before but 20 mm bore GI tubing complete all as specified and directed.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal dia Pipes complete all as specified and directed.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints 20 mm nominal dia Pipes complete all as specified and directed.

Dismantling water tanks and removing to store exc 250 n exc 500ltr complete all as specified and directed.

Dismantling water tanks and removing to store exc 500 n exc 1000ltr complete all as specified and directed.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.1000 litrs capacity complete all as specified and directed.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.500 litrs capacity complete all as specified and directed.

Taking down existing UNSV gun metal gate valve of 20mm bore in repairs complete all as specified and directed.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 20mm bore complete all as specified and directed.

Taking down existing UNSV PTMT ball valve of 20mm bore in repairs complete all as specified and directed.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball 20 mm nominal bore, 120 mm long, weighing not less than 198 gms complete all as specified and directed.

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour 20 mm nominal bore, weighing not less than 40 gms complete all as specified and directed.

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab complete all as specified and directed.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead complete all as specified and directed.

CEMENT PLASTER (IN COARSE SAND) 15 mm cement plaster on rough side of single or half brick wall of mix:1:6 (1 cement: 6 coarse sand) complete all as specified and directed.

CEMENT PLASTER (IN COARSE SAND) 15 mm cement plaster on rough side of single or half brick wall of mix 1:4 (1 cement: 4 coarse sand) complete all as specified and directed.

Finishing walls with oil bound distemper paint of required shade on new work (Two or more coat applied) complete all as specified and directed.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete all as specified and directed.

Finishing walls with Acrylic Smooth exterior paint of required shade on Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface complete all as specified and directed.

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete all as specified and directed.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour Old work (one or more coats) complete all as specified and directed.

White washing with lime to give an even shade Old work (two or more coats) complete all as specified and directed.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge complete all as specified and directed. Note: For payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead complete all as specified and directed.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc.

After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing complete all as specified and directed. Note: (a) Single / double glass panes, wire mesh and silicon sealent shall be paid separately. (b) Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (c) For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing factory made uPVC white colour casement/ casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles having minimum wall thickness of 1.70mm for series R1 and R2 profiles and 2.10mm for series R3 and R4 profiles conforming to EN:12608. in any shape, colour and disign duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimentions, EPDM gasket, hardware, SS 304 grade fastner of min 8mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part I to 14, plastic packers, plastic caps and necesary stainless steel screws etc profiles of frame, sash & mullion (if required shell be mitred cut and fusion welded mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing of gap between frame and adjacent finsished wall shall be filled with weather proof silicon sealent over backer rod of approved size and quality all complete all as specified and directed by engr in charge Fixed window/ ventilator with mullion/transom. Using R2 series with frame (33 mm & above) x (35mm & above) & mullion (33 mm & above) x (50 mm & above ) (Height upto 0.90 metre) complete all as specified and directed.

Float glass panes 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm) complete all as specified and directed.

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading complete all as specified and directed.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works complete all as specified and directed.

Dismantling C.I. or asbestos 100 mm internal dia rain water pipe with fittings and clamps including stacking the material within 50 metres lead complete all as specified and directed.

Providing and fixing 110mm bore on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes complete all as specified and directed.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5°, 110mm bore complete all as specified and directed.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain), 110mm complete all as specified and directed.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee with door, 110x110x110mm complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed.

Dismantling C.I. or asbestos 75 mm internal dia rain water pipe with fittings and clamps including stacking the material within 50 metres lead complete all as specified and directed.

Providing and fixing 75mm bore on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes complete all as specified and directed.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5°, 75mm bore complete all as specified and directed.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee with door, 75x75x75mm complete all as specified and directed.

S&F in repairs 450 x 600mm PVC body cabinet Mirror and fixing to the wall with suitable screws etc complete all as specified and directed.

Providing and fixing C.P. brass shower rose with 15 mm inlet 150 mm diameter complete all as specified and directed.

Complete removal of entire existing water proofing treatment in any position, any thickness including tarfelt, Plaster, lean concrete, gravels etc. and removing the debries out side MD land complete all as specified and directed.

M&L for cement concrete type B1,1:2:4 (20mm graded stone aggregate) as in kerb or mud stop, slightly rounded or champhered on edges complete all as specified and directed.

M&L for 10 mm thick rendering in CM 1:4 over concrete surfaces mixed with water proofing compound @ 3% by weight of cement complete all as specified and directed. Note: Water Proofing compound shall be measured and paid for seprately as "Supply Only"

Provding and carry out water proofing treatment to sound, moisture free concrete surface system includes preparation to remove loose dust, dirt, loose mortor, curing compound etc carry out cementious injction grouting at leakage points and construction joints using cement slurry modified with Cebex 100 plasticised expandive ground admixture supplies in 225 gm pouch, treatment of construction joints using polymer modified mortor prepare by using Nitobond SBR latects, application of polymer modified battaat floor, wall junction, filling of annular space around rain water outlet using conbextra GP2 non shrink cementious grouts. Andulated surface and pot hole shall be treated with epoxy mortor or putty to obtained sound/ levelled surface. Application of primer Nito proof WB primer on sound mortor slab surface. Followed by application of coat of Nito proof 600 PF liquid applied single component pitch free polyurithane coating supplied in 25 kg drum coverage @ 2.30 Kg/m2 to achieve 1.5 mm thickness in two coats complete including all tools and tackles as per manufactures specification.

Coating shall be having crackbriding of 2 mm , elonagtion (ASTMD 124) greater than 600 percentage, tensile strength (ASTM D412), 95 percenatge, 85 percentage of solid contantents, tear resistance (ASTM D624),15 KN/M, shore A hardness (ASTM D 2240), 60, water vapour transmission not more than 1 gm /M2 , water permeability (DIN-1048)-NIL, services temperature -40'C to 70 degree 'c, flash point greater than 70 'C HSE guidelines:- It is recommanded to provide adequate general and local exhust ventillations, providing protection to Eye, face, Hand andother skin by wearing appropriate glouse, google, face cilid, respiratory protection etc, directed in SDS of the product complete all as specified and directed.

Grinding Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as specified and directed.

Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms complete all as specified and directed.

M & L for Preparing surfaces plastered surface three coat (03 coat) White washing with lime on old ceiling surface complete all as specified and directed.

Injecting low viscosity grade epoxy grout by pressure by epoxy or grouting pump and compressor. Mixing:- Material components DR BECK 505C + EK411 HARDNER + SOLVENT 100:50:50 weight batching. Grouting :- fill the grouting gun with resin mix maintain desired pressure at exit (7 to 10 kg /sqcm) by monitoring pressure gauge at exit. Grout the material through prefixed nozzles in the structural elements till its refusal, seal the nozzle with epoxy sealant (EPCO 10 10) after the refusal. Monitor leakages through other nozzles while grouting and seal them as per the requirement. Repeat the process all the nozzles. Complete the poeration at pot life of material, grouting is continued to all the nozzles from bottom to top and not from top to bottom. cleaning the gun and accessories (Valves, pipes and other fixtures) with T-60 thinner / or equivalent of dr. fixit. Krishna chemical, sunanda etc. The work should be helmet, safety belt and adequate labour insurance under the supervision of qualified supervisor etc. complete all as specified and directed.

M & L for Wire netting of galvanised steel wire 1.40mm dia and 25 mm size of mash fixed with tinned tacks of wire staples complete all as specified and directed.

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc all as specified and as directed.

Taking down sub main wiring complete including fitting and fixtures, removing materials for making good disturbed surfaces of walls, floors, roof etc, all as specified and as directed.

Taking down carefully unserviceable DBs any type/ size and disconnecting and making good disturbed surfaces complete all as specified and directed.

M & L Point wiring for light point with 1.5 sqmm FRLSH PVC insulated copper coductor single core cable in concealed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable etc complete all as specified and directed for the following;-

One light point controlled by one switch.

One two way light point controlled by 02 Nos 02 way switches

One fan / Exhaust fan point controlled by one switch and one regulator.

One bell point controlled by one bell push

One 3 pin switch socket outlet point 5 Amps on independent board.

One 3 pin switch socket outlet point 5 Amps on same board with other switch.

All as per item above here in before but with copper conductor cable for one 3 pin socket outlet, 15 amp independent, with cable 3 core X 4 sqmm size.

S & Fix modular socket out let 6A 2/3 on combined 2 module complete all as specified and directed.

S & Fix modular socket out let 6A/16A-2/3 pin combined 2 module complete all as specified and directed.

Supply and fixing of call bell / buzzer suitbale for single phase, 230 V, complete all as specified and directed.

Supply and fixing of 2 module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. complete all as specified and directed.

S & F ceiling rose, single phase, PVC polycarbonate, insulated body complete all as specified and directed.

Removing the existing ceiling fan and servicing, cleaning and spray painting and refixing the same with necessary 3 core wire and accessories complete all as specified and directed.

M & L for opening Unserviceable ceiling fans, rewinding of ceiling fan any type with super enamelled copper winding wire of same gauge & number of turns in each coil including insulating varnishing backing etc., connecting reassembly, testing complete all as specified and directed.

S&F Blades for 1200 mm ceiling fan in place of unserviceable blades including required nuts/ washers etc. accessories complete all as specified and directed.

S&F Canopy for 1200 mm ceiling fan in place of unserviceable Canopy including required nuts/washers etc. accessories all as directed.

S&F down rod 2 feet for 1200 mm ceiling fan in place of unserviceable downrod including required nuts/ washers/ pins etc. accessories complete all as specified and directed.

Supply and fixing in replacement of existing unserviceable T/L fitting 36/40 W and Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED Tube light fitting 10 watt, 230 volts, sleek and seamless profiled extruded aluminium batten with an efficient diffuser to illuminate work and retail spaces complete with all accessories complete all as specified and directed.

S&F LED Down Light 12 watt, 230 volts, surface mounted complete with all accessories complete all as specified and directed.

S & Fix 2 x 2 Ultra modern recess mounting 36 watts luminair with high performance LEDs, suitable for mounting with Armstrong/ Grid ceiling complete all as specified and directed.

S & Fix LED building security light 30/35 W building pressure die cast aluminium housing with high power LEDs, lens & toughened glass, with IP 66 and bracket, nut, bolt, clamp etc complete all accessories and fixing arrangement complete all as specified and directed.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLSH PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required complete all as specified and directed. Note: All copper conductors including conduit shall be measured as one unit length.

(a) 2 x 1.5 sqmm + 1 x 1.5 sqmm earth wire

(b) 2 x 4 sqmm + 1 x 4 sqmm earth wire

(c) 2 x 6.0 sq. mm + 1 x 6.0 sq. mm earth wire

(d) 4 x 6.0 sq. mm + 2 x 6.0 sq. mm earth wire

Supply and fixing 20 A, SPN Industrial socket outlet with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc, as required complete all as specified and directed.

Removing the existing exhaust fan any type and after servicing, cleaning and spray painting, refixing the same with necessary 3 core wire and accessories complete all as specified and directed.

M&L for rewinding of exhaust fan any type with super enamelled copper winding wire of same gauge & number of turns in each coil including insulating varnishing backing etc., connecting reassembly, testing complete all as specified and directed.

Taking down the existing unserviceable Geyser and after disconnecting electrically & mechanically and examine & carry out the servicing/overhauling the geyser of 25/50 ltrs capacity by thoroughly cleaning the tank, thermostat, heating element and LED Lamp indicator, testing in all respect for smooth running and refixing complete all as specified and directed.

S & Fix sheet metal enclosure MCCB DB VTPN double door 4 way with 160 Amps MCCB, suitable for 415 V with 200 amps rated bus bar including flushed on walls and making good disturbed surfaces all as specified and as directed.

Supplying and fixing 8 way, single pole and neutral sheet steel MCB distribution board, 240 V on surface / recess, complete with tinned copper bus bar neutral bus bar, earth bar, din bar, interconnection, powder painted including earthing etc as required complete all as specified and directed.

Supplying and fixing 12 way, single pole and neutral sheet steel MCB distribution board, 240 V on surface / recess, complete with tinned copper bus bar neutral bus bar, earth bar, din bar, interconnection, powder painted including earthing etc as required complete all as specified and directed.

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required complete all as specified and directed.

S&F MCCB TPN 63 A, 415V 'C' curve with 10kA breaking capacity complete all as specified and directed.

S & Fix MCB, single pole, 240 volts, 6 to 32 Amps, complete all as specified and as directed.

S & Fix MCB, single pole and neutral 240 volts, 32 Amps, complete all as specified and directed.

S & Fix 160Amps MCCB 4 Pole, 415 V, fixed type with breaking capacity 36 KA complete all as specified and directed.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required complete all as specified and directed.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required complete all as specified and directed.

M&L for Taking down old oldunserviceable GI Pipe any type and size completely and taken as schedule of credit & making good disturbed surfaces complete all as specified and directed.

Supply and laying tubes, Galvanised, "medium" grade, with all fittings and fixed to walls, ceiling or laying in floors, all as specified for following sizes:-

(a)150 mm dia

(b) 80 mm dia

(c) 50 mm dia

(d) 20 mm dia

Providing and fixing gun metal gate valve with C.I. wheel of approved quality for the following sizes:-

(a) 50 mm bore

(b) 20 mm bore

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out soft / loose soil for laying cables / pipes / erection of poles etc. complete all as specified and directed.

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Returning filling in soil including spreading levelling watering well ramming in layers not exceeding 25 cm each complete all as specified and directed.

Making connection of G.I. distribution branch with G.I. main of 50 to 80 mm dia sizes by providing and fixing tee, including cutting and threading the pipe etc. complete all as specified and directed.

M & L for construction of valve chamber with brick work/ PCC block (1:4:8) Type D5, 20 CM thick masonry built in 1:6, 10 mm thick internal & 10 mm thick external plaster in 1:4 cm provided with 3 mm thick MS sheet cover and 40 x 40 x 3 mm MS angle iron frame fixed in copping PCC 1:2:4 type B-1 with locking arrangement and handle, painting of MS work with one coat of red oxide and two coats of synthetic enamel red paint complete including excavation and earthwork all as specified for 900x900x900 mm size complete all as specified and directed.

S & F C.I float valve of bore size 20mm complete all as specified and directed.

S & F C.I Sluice Valve Class PN 1.6 bore size 150 mm complete all as specified and directed.

S& F CI NRV Class PN 1.6 bore size 65 mm complete all as directed.

Taking down old U/S LT UG cable of any type complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of folowing sizes:-

(a) 10 sqmm 4 core cable.

(b) 16 sqmm 4 core cable.

(c) 25 sqmm 4 core cable.

(d) 35 sqmm 3.5 core cable.

(e) 50 sqmm 3.5 core cable.

(f) 70 sqmm 3.5 core cable.

(g) 240 sqmm 3.5 core cable.

Supplying and laying of following size DWC pipe ISI marked along with all accessories etc confirming to IS 14930, part II complete with fitting and cutting, jointing etc. in trench/open, for LT UG cable protection complete all as specified & directed by Engr-in-charge of following sizes:-

(a) 100 mm bore

(b) 80 mm bore

(c) 40 mm bore

Supply and fixing GI tubing (ISI Marked), light grade for cable protection with all necessary fittings as required, laid in trenches, under road/floors or on electric poles complete all as specified and directed of following sizes:-

(a) 80 mm bore

(b) 50 mm bore

(c) 40 mm bore

M&L for cutting of bituminous road/ floor for laying of pipe/ cables not exceeding 30 cm wide and not exceeding 60 cm deep including refilling with material and watering well ramming/ compacting and making good with PCC 1:2:4 type B-1, 100 mm thick complete all as specified and directed.

S&F cable route indicator made out of CI circular disc engraved embossed HT/LT cable, 100 mm dia, 10 mm thick fixed on MS round bar iof 10 mm thick 60 cm long duly painted with primer and synthetic enamel paint. Indicator shall be embedded in PCC block of size 40 x 40 x 40 mm and indicator shall be 20 cm above the ground level complete all as specified and directed.

Supply, Fabricate, install, connect, test and commission Outdoor type dust & Vermin proof LT electrical panel board, 1100 volts, 50 Hz AC supply, fully compartmentalised for cable chamber and busbar chambers with adequate space made out of 3 mm thick CRCA sheet for load bearing like all over body, front and back cover with hinges and aldrops with DC locks CRCA poweder coated and 2.0 mm thick MS Sheet for non load bearing and portions, complete with one coat of powder coating including suitable angle iron/ flat iron frame work/ supports bottom 50x50x6 mm MS channel as base and chamber for metering equipment complete suitable for mounting following switch gear items internally connected with suitable capacity aluminium strip/ rods insulated and connection wirings with FRLS copper conductor complete mounted on PCC pillars foundation, arrangements for bus bar trunking system, cable connection using new lugs complete with danger notice all as specified and comprising of the followings:- Note: (i) Existing cables which removed from old panel board will be fixed with new lugs during fixing in new panel board (as if required). (ii) Getting of approval for Panel board drawing from Engr-in-Charge is necessary before fabrication. (iii) All swith gears should be fixed with 06 mm thick Fibre sheet.

a) LED/ Neon indicator bulb in RYB Colour - 1 Set. b) 4 No aluminium Bus bar 1000 amps with chamber c) Digital Multi function meter for showing Amps (upto 630 Amps) and Voltage (upto 500 voltage) with suitable CT and PT f) ACB 4 Pole, 415 V, Adjustable thermal & adjustable magnetic type, 630A with breaking capacity 50 KA - 01 Nos Out going: h) MCCB 4 Pole, 415 V,adjustable type, 400 A with breaking capacity 50 KA - 04 Nos h) MCCB 4 Pole, 415 V,adjustable type, 250 A with breaking capacity 36 KA - 02 Nos I) suitable cable gland for incoming and outgoing cable

Supply Fabricate, install, connect, test and commission Outdoor type dust & Vermin proof LT electrical panel board, 1100 volts, 50 Hz AC supply, fully compartmentalised for cable chamber and busbar chambers with adequate space made out of 3 mm thick CRCA sheet for load bearing like all over body, front and back cover with hinges and aldrops with DC locks CRCA poweder coated and 2.0 mm thick MS Sheet for non load bearing and portions, complete with one coat of powder coating including suitable angle iron/ flat iron frame work/ supports bottom 50x50x6 mm MS channel as base and chamber for metering equipment complete suitable for mounting following switch gear items internally connected with suitable capacity aluminium strip/ rods insulated and connection wirings with FRLS copper conductor complete mounted on PCC pillars foundation, arrangements for bus bar trunking system, cable connection using new lugs complete with danger notice all as specified and comprising of the followings:- Note: (i) Existing cables which removed from old panel board will be fixed with new lugs during fixing in new panel board (as if required). (ii) Getting of approval for Panel board drawing from Engr-in-Charge is necessary before fabrication. (iii) All swith gears should be fixed with 06 mm thick Fibre sheet.

a) LED/ Neon indicator bulb in RYB Colour - 1 Set. b) 4 No aluminium Bus bar 600 amps with chamber c) Digital Multi function meter for showing Amps (upto 400 Amps) and Voltage (upto 500 voltage) with suitable CT and PT d) MCCB 4 Pole, 415 V, Adjustable thermal & adjustable magnetic type, 400A with breaking capacity 50 KA - 01 Nos Out going: e) MCCB 4 Pole, 415 V,adjustable type, 63 A with breaking capacity 25 KA - 16 Nos f) suitable cable gland for incoming and outgoing cable

Supply Fabricate, install, connect, test and commission Outdoor type dust & Vermin proof LT electrical panel board, 1100 volts, 50 Hz AC supply, fully compartmentalised for cable chamber and busbar chambers with adequate space made out of 3 mm thick CRCA sheet for load bearing like all over body, front and back cover with hinges and aldrops with DC locks CRCA poweder coated and 2.0 mm thick MS Sheet for non load bearing and portions, complete with one coat of powder coating including suitable angle iron/ flat iron frame work/ supports bottom 50x50x6 mm MS channel as base and chamber for metering equipment complete suitable for mounting following switch gear items internally connected with suitable capacity aluminium strip/ rods insulated and connection wirings with FRLS copper conductor complete mounted on PCC pillars foundation, arrangements for bus bar trunking system, cable connection using new lugs complete with danger notice all as specified and comprising of the followings:- Note: (i) Existing cables which removed from old panel board will be fixed with new lugs during fixing in new panel board (as if required). (ii) Getting of approval for Panel board drawing from Engr-in-Charge is necessary before fabrication. (iii) All swith gears should be fixed with 06 mm thick Fibre sheet.

a) LED/ Neon indicator bulb in RYB Colour - 1 Set. b) 4 No aluminium Bus bar 600 amps with chamber c) Digital Multi function meter for showing Amps (upto 400 Amps) and Voltage (upto 500 voltage) with suitable CT and PT d) MCCB 4 Pole, 415 V, Adjustable thermal & adjustable magnetic type, 400A with breaking capacity 50 KA - 01 Nos Out going: e) MCCB 4 Pole, 415 V,adjustable type, 125 A with breaking capacity 25 KA - 04 Nos f) MCCB 4 Pole, 415 V,adjustable type, 63 A with breaking capacity 25 KA - 14 Nos g) suitable cable gland for incoming and outgoing cable

Supply Fabricate, install, connect, test and commission Outdoor type dust & Vermin proof LT electrical panel board, 1100 volts, 50 Hz AC supply, fully compartmentalised for cable chamber and busbar chambers with adequate space made out of 3 mm thick CRCA sheet for load bearing like all over body, front and back cover with hinges and aldrops with DC locks CRCA poweder coated and 2.0 mm thick MS Sheet for non load bearing and portions, complete with one coat of powder coating including suitable angle iron/ flat iron frame work/ supports bottom 50x50x6 mm MS channel as base and chamber for metering equipment complete suitable for mounting following switch gear items internally connected with suitable capacity aluminium strip/ rods insulated and connection wirings with FRLS copper conductor complete mounted on PCC pillars foundation, arrangements for bus bar trunking system, cable connection using new lugs complete with danger notice all as specified and comprising of the followings:- Note: (i) Existing cables which removed from old panel board will be fixed with new lugs during fixing in new panel board (as if required). (ii) Getting of approval for Panel board drawing from Engr-in-Charge is necessary before fabrication. (iii) All swith gears should be fixed with 06 mm thick Fibre sheet.

a) LED/ Neon indicator bulb in RYB Colour - 1 Set. b) 4 No aluminium Bus bar 300 amps with chamber c) Digital Multi function meter for showing Amps (upto 200 Amps) and Voltage (upto 500 voltage) with suitable CT and PT d) MCCB 4 Pole, 415 V, Adjustable thermal & adjustable magnetic type, 200A with breaking capacity 36 KA - 01 Nos Out going: e) MCCB 4 Pole, 415 V,adjustable type, 125 A with breaking capacity 25 KA - 02 Nos f) MCCB 4 Pole, 415 V,adjustable type, 63 A with breaking capacity 25 KA - 07 Nos g) suitable cable gland for incoming and outgoing cable

Material and Labour for Earthing complete with with 600 mm x 60 mm x 6.15 mm thick, galvanized steel earth plate electrode buried vertically in ground (not less than 2.25 meters deep below normal ground level), with top edge of earth plate not less than 1.5 meter below ground level connected to and including G.I strip of size 25mm x 4 mm by means of bolts/ nuts/ check nuts and washers of galvanized steel, GI Strip encased in and including 40 mm bore GI light grade protection pipe starting from top edge of the earth plate laid in ground/ floors fixed on wall. GI strip to be connected with LT Panel with provision of charcoal dust & common salt all around the earth plate 15 cm layers including necessary excavation and earth work in any type of soil/strata, provision of concrete earth pit using PCC 1:3:6 type C-2 including RCC cover using PCC 1:2:4 type B1 20 mm dia GI light grade with wire mesh and tunel for watering arrangement, complete all as per DSR specification including testing after completion of earth complete all as specified and directed.

S & Fix LED post top fitting powder coated aluminium die cast and spun aluminium body with clear/ opal diffuser 25 watt, 5700K, IP 65 high efficacy suited for installation in existing pole including all connected accessories complete all as specifed and directed.

Supply and Fix 20 watts Gate light fitting New generation, post-top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source complete all as specified and directed.

S&F Automatic Power Factor Correction (APFC) Panel for 3 Phase, 415 V & 50 Hz system of capacity 50 KVAR without incoming MCCBs complete all as specified and directed.

M&L for Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure complete all as specified and directed.

Providing and laying cement concrete 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) complete all as specified and directed.

Providing and laying factory made precast solid concrete block of 200mm thickness grade M-10 made of CND based from approved in CM 1:6 complete all as specified and directed.

Providing and laying cement concrete 1:2:4 (1 Cement: 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources) in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing complete all as specified and directed.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (1 cement: 2 coarse sand (zone-III) derived from natural sources:4 graded stone aggregate 20 mm nominal size derived from natural sources) complete all as specified and directed.

Please Enable Macros to View BoQ information