ADDN/ALTN and SPECIAL REPAIR OF 04 BLOCK (61 QTRS) OF JCOS/OR MD ACCN

Amount

M&L for Preventive treatment against the danger of carbonation in exposed faces of RCC members :- (i) Cleaning existing surfaces of RCC members and making surface free of loose material, oil, grease etc. by vigorous wire brushing including light grit blasting where necessary as recommended by Engr-in-charge. (ii) Further, cleaning using biocide(as recommended by manufacturer) to ensure that surface is free of algae and fungus and no trace of paint (any type) left out. Sand blasting to be done to remove trace of paint. (iii) Cleaned surface to be allowed to dry. (iv) Spray a coat of primer (as recommended by manufacturer) over dry cleaned surface as required prior to final finish. Primer shall be diluted in proposition 2:1 with mineral turpentine. After application, primer shall be allowed to dry for 03 hours or as directed. (v) Apply a coat of neat Aliphatic Acrylic anti-carbonation (ACC) over the primed surface with air / spray gun at nominal rate of 3.5 ltrs per sqm as recommended by manufacturer. (vi) Apply a more coat of Aliphatic Acrylic anti-carbonation (ACC) after 5-6 hours as recommended by manufacturer complete all as specified and directed. (vii) Sprinkle sand cover over surface to receive new

M&L for followings :- (i) Removing plaster & finishes all around the coloumns, slabs & beams (on all four sidescription of column to full height , three sidescription of beam to entire span & bottom of slab to area as directed) (ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible) (iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed) (iv) Cleaning exposed concrete substrate by using water jet. (v) Removing visible rust along the length of reinforcement using hand tools as approved. (The Engr-in-charge may order sand blasting if rust is approved) (vi) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out complete all as specified and directed.

M&L for providing rust proof /anti corrosive treatment to bars :- (i) cleaning of all exposed bars (new & old) alround (ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer (iii) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating. Superficial area of member to be considered for measurement

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

M&L for treatement of cracks found in the core concrete :- (i) Opening of crack by making a ' V' notch/groove of size 12mm x 12mm over the entire length of the crack as identified by the Engr-in-charge. (ii) cleaning ' v' notch/groove of all dust/debris/loose material (iii) Drilling hole of 16mm dia and about 40mm deep along the length of crack @ (300 mm c/c or thickness of structural member whichever is less) Note : In case length of crack is found less than 300 mm then min 2 holes shall be drilled. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole drilled above and fixing the nipple with the help of fast setting epoxy putty. (v) seal the surface around the nipple and the area of crack between successive nipples polymer modified mortar to ensure that there is no leakage from any gap. (vi) Allow the polymer modified mortar to cure for 24 hours and ensure that firmly fixed in postion. (vii) cleaning nipple one by one commencin from the top to bottom in case of column and one by one in alternate direction incase of beam/slab using blow compressed air followed by water injection. An Ensuring that there is no obstruction in free flow of grouting materials complete all as specified and directed.

(viii) Injecting " resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Note : pressure shall be in the range of 1-2 kg/sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardenere shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly. (ix) Allow entire effected surface to cure for 24 hours. (x) cutting out projected parts of the nipple & seal the hole in the nipple with epoxy putty as recommended by manufacturer. (xi) cleaning exposed surface of substrate off any dust /loose material after ageing of the grout as recommended by manufactuer.

M&L for treatement of core concrete when found to be porous/honeycombed :- (i) Marking the area in marker as directed by the Engr-in-charge. (ii) Drilling holes of 16mm dia in an orthogonal grid on exposed cone of member @ 150 mm c/c both way, depth of the hole shall be about 60% of the element thickness. (iii) clean the drill hole using compressed air removing the dust/dirt. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole with the annular space around the nipple sealed with epoxy putty. It shall be ensured that the injected grount does not leak. (v) Allow the nipple to cure for 24 hours. (vi) Injecting " Resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Note : pressure shall be in the range of 2-3 kg/sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardenere shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly.

(vii) Allow entire effected surface to cure for 24 hours. (viii) cutting out projected parts of the nipple & seal the hole in the nipple with epoxy putty as recommended by manufacturer. (ix) cleaning exposed surface of substrate off any dust /loose material after ageing of the grout as recommended by manufactuer.

S&F 12mm dia steel sheer connector in grid pattern in between old core and new concrete as wherever directed by Engr-in-charge and as specifed by manufactuer including drilling hole of depth of 100 mm and chemical anchoring with pure epoxy resin anchoring mortar (Master flow 935 of BASF or equivalent FOSROC/SIKA). (The cost of drilling hole &chemical anchoring with epoxy resin is inclueded in this item) complete all as specified and directed. (Note:- Steel is also measured with this item)

M&L for Providing & Pouring Micro concreting M-40 grade :- (i) Dry concrete substrate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound concrete substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above pour Micro concreting M40 grade, Make : MasterEmaco S46T of BASF or equivalent FOSROC/SIKA using approved mixing machines/pumping under pressure via approved pneumatic pump at the locations to be repaired in RCC beams & columns etc,. Adding of aggregates will be permitted only as per manufacturer’s recommendation without compromising the strength. The rate shall include cost of all materials (except re-bar) labour charges for mixing, pouring concrete, cost of tools, lead & lift of materials, transportation etc., to carry out the complete work complete all as specified and directed. Note : The cost of micro concrete M-40 grade & Epoxy bond coat is inclueded in this item.

M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 8 mm dia bar - drilling length 80 to 100 mm - 384 Nos Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar (Master flow 935 of BASF or equivalent FOSROC/SIKA) with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)

M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 16 & 20 mm dia bar - drilling length 160 to 180 mm - 336 Nos Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar (Master flow 935 of BASF or equivalent FOSROC/SIKA) with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)

M&L for use & waste of form work using steel sheets , steel bracing, propping etc around structural members where micro concreting to be done and keeping form work in position till required specified period complete all as specified and directed. Note : Form work shall be 100% leak proof. For purpose of payment area in touch with concrete shall be measured.

S&F for stengthening existing reinforcement by use of mild steel bars of any dia , cut to length, bent to shape required, including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Description of Work / Item(s)

Amount

Dismantling of brick tiles (laid flat or on edge) on roof surface.laid bedded and pointed in any mortar complete all as specified and directed

Demolition of mud in roof, any thickness, including plastering and leeping incl necessary scaffolding arrangement complete all as specified and directed(whether full thickness removed or only a part there of) and removing from cantonment area or as directed complete all as specified and directed

M&L for brushing neat cement slurry with 3.00 Kg of cement per Sqm on existing surfaces complete all as specified and directed

M&L 50 mm thick (average thickness) plain cement concrete 1:2:4 type B-0 using (12.5 mm graded aggregate), as in roof ,padding to maintain the uniform slope complete all as specified and directed. Note : - WPC shall be measured & paid separately.

M & L for rendering 15 mm thick (average) plaster on concrete surfaces in CM (1:4) on roof, mixed with water proofing compound and finishing the surface even and smooth without using extra cement complete all as specified and directed

S&F APP based polymeric water proofing membrane minimum weighing 3 Kg/sqm and 3mm thick reinforced with polyster non wove fabric (weight not less than 150 gms/sqm laid over and including applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per sqm by torch application including cleaning of surface complete all as per approved manufacturer's instructions complete all as specified and directed Note:-The water proofing treatment shall be carried out by manufacturer or their auth applicators as per manufactures instruction and as directed by Engr in Charge.

M&L for cement concrete tiles 25cmx25cmx22mm thick laid over and including 20mm thick screed in CM 1:6 and jointed grouted and pointed in CM 1:3 complete all as specified and directed

Demolition unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

Demolition of PCC in ground floors and pavings n'exc 15 cm thick below or above ground level (unreinforced) complete all as specified and directed

Demolition of cement concrete in above ground floors exc 15cm thick above ground floors complete all as specified and directed

M&L for applying a coat of cement slurry @ 0.488 Kg/Sqm mixed with tapercreate @ 0.253 Kg/Sqm after cleaning and drying the old/new surfaces(Make of tapercreate M/S CICO Engg Services) then applying the layer of fibre glass cloth while the above coat is still green. The overlap of fibre glass cloth shall be not less than 100 mm.(Make of fibre glass cloth M/S The Structure Water Proofing Co Pvt Ltd) and then applying 1.5 mm thick layer @ 1.288 Kg/Sqm mixed with taper create @ 0.570 Kg/Sqm and coarse sand @ 1.289 Kg/Sqm. Allow the treatment to air curing for four hours followed by water curing for 48 hours complete all as specified and directed

M&L for 10 mm thick cement plaster on brick/ concrete surface in CM 1:3, finished even and smooth surface with out using extra cement but mixing water proofing compound at the rate of 2% of cement by weight complete all as specified and directed (Note :-WPC shall be paid separately).

Supply only liquid water proofing compound.(ISI Marked) complete all as specified and directed

M&L Cement concrete type F-2 (1:5:10) using 40 mm graded stone aggregate in mass concrete in sunken floor complete all as specified.

M&L 75 mm thick PCC type D2 (1:4:8) using 40 mm graded stone aggregate as in sub base of flooring complete all as specified and directed

M&L for 25mm thick cement concrete type B-0 1:2:4 (12.5mm graded aggregate) as in sub floors finished rough.

Roughening surfaces of old concrete floor/wall by picking, sweeping clean and washing down with water to remove dust, etc and brushing and applying neat cement slurry with 3.0 Kg of cement per sq metre complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M & L for Glazed Ceramic coloured tiles in vertical surface 300x450x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and including 10mm thick backing coat of CM (1:4), complete all as specified and directed.

M&L Non Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick in CM 1:6 complete all as specified and directed.

M&L for Non skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick in CM 1:6 complete all as specified and directed.

All as per item No 21 here in before but as in skirting laid over and including 10mm thick backing coat of CM (1:4)

M&L 40mm thick PCC flooring 1:2:4 type B1 using 20mm graded stone agg finished even & smooth without using extra cement complete all as specified and directed.

M&L for machine cut kota stone slab flooring, and (one Pieces) as in steps (Treads), 20-25mm thick over cement screed bed 20mm thick with CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

All as per Srl item No 24 here-in-before but of riser of step, dado skirting etc

S&F in repair vitreous china squatting pan, (Orissa pattern) size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap etc including making good to floor complete all as specified and directed

M&L for vitreous china wash hand basin flat back size 550x400 mm size white excluding taps waste chain and plug and porcelain stopper but including brackets and 32 mm dia waste fittings brass chromium plated with long screwed shanks and fly nuts, 32MM X 600 MM long PVC waste pipe flange end bedded in CM 1:4 and other end fixed complete all as specified and directed (Note - WHB will be supported on angle iron of size 50x50x5mm duly painted with two coats of synthetic enamel paint for securing WHB).

M & L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered and hold fast on edge including necessary form work complete all as specified and directed

Supply only water proofing compound.(ISI Marked) complete all as specified and directed

M & L for green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble of any shade other than white and black complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps cooking platefom,and other similar situations complete all as specified and as directed

S&F in repairs low level flushing cistern of 10 ltrs capacity PVC valveless, syphonic action type, white with inlet ball valve float and handle complete all as specified.

S&F in repairs PVC connections 450mm long with brass unions at both ends suitable for 15mm bore pipe, complete all as specified and directed

S&F in repairs CP connection 15 mm size with brass nut of length 600 mm complete all as specified and directed

S&F in repairs brass CP mixer fancy for mixing hot & cold water screwed down for iron pipe of 15 mm bore pipe with all assembly complete all as specified and directed

S&F in repairs elegent mirror PVC cabinet (PTMT alloy) complete all as specified and directed

S&F Chromium plated soap dish with screw complete all as specified and directed

S&F aluminium Peg set of 3 pegs as per sample complete all as specified and directed

M&L Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 105gms) complete all as specified and directed

S&F PVC laminated GI wire 2.00mm dia for cloth drying with S&F fastener as per site requirement complete all as specified and directed.

S & F in repairs brass chromium plated tubular towel rail, 20 mm dia D type , 60 cm long between flanges complete all as specified and directed

S&F in repairs brass chromium plated shower rose of size 125 mm with arms including fixing to steel pipe complete all as specified and directed

S&F in repairs bib tap, brass chromium plated fancy type, long body screwed down, screwed for iron pipe 15 mm bore complete all as specified and directed

S&F in repair Conceeled stop cock,15 mm bore, chromium plated ,with long shank and cup, fancy type, complete all as specified and directed

S&F in repair 15 mm dia brass chromium plated angle valve screwed at ends including necessary extention piece and fixed complete all as specified and directed

S&F in repairs Cast iron floor trap with grating including jointing to waste pipe in run lead, dia of outlet 75 mm in cement concrete type B1 (1:2:4) complete all as specified.

S & F in repairs Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed

S&F PVC waste pipe 32/40 mm bore, 65 cm long complete all as specified and directed

S&F in repair staianless plate rack AISI 316 grade made of 1mm thick stainless steel sheet of size 775 mm x 900 mm x 250mm consisting of 3 shelf for bowls and one shelf for keeping six nos of big utensil and seven nos of small utensils divided by 10 mm dia stainless steel hollow pipe @ 60 mm centre to centre or as per drg and sample kept in GE's office complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and n.exc 2 sqm each , refixing in the same opening complete all as specified and directed

Taking down chowkats or frames with shutters (without taking of shutters from the frames) exc 1.5 Sqm but n.exce 4 Sqm each removing from store complete all as specified and directed

Taking down chowkats or frames with shutters n.exc. 1.5 Sqm each (without taking off shutters from the frames)removing from store complete all as specified and directed

S&F mild steel work such as in door Chowekats,, tie bars etc including embedding into concrete and making holes for screwing of nut, bolts, cutting top to shape as directed, drilling holes, notching for wire etc confirming Fe 410-0 or Fe 310-0 all as specified and directed.

M&L for Cement concrete type C-0, 1:3:6 (using 12.50 mm graded agregate) in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and directed

S&F fabricated aluminum window with powder coated anodized aluminum frame of section 63.5mm x 38.10mm x1.5mm thick, shutter with section 47.62mmx44.45mmx1.5mm thick including aluminum anodized “D “ handle, hinges, peg stays, tower bolts, etc including jointing cleats for fixing builder's hardware fittings & stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples including necessary fittings/fixture /aluminum snap beads complete all as specified. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

M&L poweder coated aluminium anodised three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5mm thickness (section no. 20831 of JINDAL) and of shutter size 40 mm x 18 (with 9.00 mm interlocking legs) x 1.45 mm thick (section no. 20737 of JINDAL) section (two shutter glazed, covering half of span of opening each & one shutter sketlon covering half of span of opening ) incl provn for making windows air tight, including 95mm aluminium handle with spring lock , stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4mm and fixed with steel wire stapples and 4mm thick plain glass including necessary fitting/ fixture/ aluminium snap beads complete all as specified. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

S& F Aluminium powder coated Grill (DECO grill DG 103 of 7.5 mm thick of M/s ELESAR, M/S Royal Grill , M/S National Grill Associated profiles & Aluminium Ltd ) fixed with suitable 'F' Section (No 8584) 15.30 X23.40X 1.40 mm (minimum), fabricated adn riveted to aluminium window / ventilators complete all as specified and directed .

S&F 35mm thick plain framed 2nd cl hardwood panelled shutter (two panels ) with lock rail & panel of 9mm BWP commercial ply or 12mm veneered particle with commercial veneering on both face, the size of rail and style as per IS 1003 (Part-1) kiln seasoned and chemically pressed, treated complete incl 15 to 20 mm tapering bedding on one face of second cl hardwood fitted to chowkhats complete all as specified.

S&F for 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats all as directed.

S & F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples etc complete all as specified and directed.

S & F in repair for mild steel, 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as spd.

S&F factory made solid FRP door frame of size 90mm x 45 mm made out of FRP sheet , complete all as specified and directed

S&F factory made solid panel FRP door shutter 30mm thick premoulded design made out of solid core, laminated 1.5 mm to 2mm thick GRP/FRP made of superior all seson, weather resistant polyyester get coat followed by laminating polyster resin of 450 gm glass mat termite all as per manufacturers specification

S&F 100mm size butt hinges stainless steel of AISI 304 complete all as specified and directed.

S&F 300 mm long, stainless steel of AISI 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clipss of sheet, cast or extruded sections and fixing bolts and fixed etc complete all as specified and directed.

S&F stainless steel of AISI 304 grade barrel tower bolt 200 mm long, extruded section, etc complete all as specified and directed.

S&F stainless steel of AISI 304 grade handle of size 200mm size long etc. complete all as specified and directed.

S&F brass magic eye for panelled/flush shutter 35mm thick complete all as specified and directed.

M&L for preparing old decorated steel surfaces of any description not otherwise described over 10 cm width or girth & applying two coat of synthetic enamel paint of any colour complete all as specified.

M&L preparation of newly surfaces of steel of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over & including one coat of red oxide primer complete all as specified.

M&L preparation of new or previously untreated surfaces of wood of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over & including one coat of pink primer complete all as specified.

M&L preparation of old painted surfaces of wood of any description not otherwise described width or girth and applying two coats of synthetic enamel paint complete all as specified.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed

S& F in repairs factory made PVC cupboard frame of size 75 mm x 40 mm with a wall thikness of 4mm , made out of extruded 4 mm thick prelam PVC sheet of density 600 / cbm manufactured by an ISO -9001-2015 certified company , reinforced with 15 mm x 15 mm MS square tubes of 19 gauge thickness throughout the frame and mitre cut at two corners and jointed with 2 nos of 150 mm long brackets of 10 mm x 10 mm MS Square tubes .The door frame shall be fixed to wall using 65 /100 long MS screws to be provided for each vertical member and minimum of 2 nos of screw to be provided horizontal member etc . complete as per direction of Engr-in-Charge

S&F factory made PVC flush type shutter and partition of 18 mm thickness with one side lamination & other side balancing lamination sheet 18mm thick PVC sheet of density 600 / cbm manufactured by an ISO -9001-2015 certified company ,and all required brackets 5.5 screw etc. The panell shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specificationmentioned as per drawing including necessary fittings, locking and fixing arrangement ie piano hinges, handles, magnetic catches etc complete all as specified and directed

S&F stainless steel handle of of AISI 304 size 100 mm size long , etc complete all as specified and directed

S&F 100 mm long, stainless steel of AISI 304 grade, hasp and staple, safty type, incl bolt to hinge plate and fixed with screws etc. complete all as specified and directed.

S&F stainless steel of AISI 304 grade floor door stopper with hard drawn steel spring 140 mm long etc complete all as specified and directed

S&F, drapery curtain rods, stainless steel 25mm dia of approved quility with decorative wooden finish and two number brackets fixed in brick/concrete wall and same finished knobs on each end of curtain rod including 8 nos(min) match up rings etc complete all as specified

Demolition of cement concrete (unreinforced) in ground floors and paving n.exc 15cm thickness (below or above ground level) complete all as specified and directed

M & L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75mm thick, finished fair and even without using extra cement, complete all as specified and directed

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound grade 'A' complete all as specified and directed

Cutting chases or making holes, pinning in. making good to facings where required and pointing in CM 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting n.exc 10 cm girth complete all as specified and directed

S&F 15mm bore galvanised iron pipe medium grade with all fittings fixed to wall and ceiling or laid in floor including taking down of old GI pipes and connections complete all as directed.

S&F 20 mm bore galvanised iron pipe medium grade with all fittings fixed to wall and ceiling or laid in floor including taking down of old GI pipes and connections complete all as directed.

S&F 32 mm bore galvanised iron pipe medium grade with all fittings fixed to wall and ceiling or laid in floor including taking down of old GI pipes and connections complete all as directed.

S&F 50 mm bore galvanised iron pipe medium grade in short length with all fittings fixed to wall and ceiling or laid in floor including taking down of old GI pipes and connections complete all as directed.

Refixing of old steel tubing and connection in new or old position (Wall/Ceiling etc) incl cleaning for refixing, bore of pipe 15 mm dia including taking down of old GI pipes and connections complete all as specified and directed

Refixing of old steel tubing and connection in new or old position (Wall/Ceiling etc) incl cleaning for refixing, bore of pipe 20 mm dia including taking down of old GI pipes and connections complete all as specified and directed

Refixing of old steel tubing and connection in new or old position (Wall/Ceiling etc) incl cleaning for refixing, bore of pipe 50 mm dia including taking down of old GI pipes and connections complete all as specified and directed

Dismantling water tanks of capacity exc 250 litres but n.exc 500 litres complete all as specified and directed..

S&F 500 ltr capacity triple layer, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part II complete all as specified and directed

S & F in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 15 mm bore complete all as specified and directed

S & F in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore complete all as specified and directed

S&F Ball brass valves, high pressure, with of PTMT with epoxy coated aluminium rod & high desity plastic ball ascrewed for iron pipe of 20mm bore and fixed complete all as specified and directed

S & F in repairs CI soil, waste and vent pipe in any length with or without ears, with cement joints, fixed to walls of 100 mm dia sand cast pipe complete all as specified and directed.

S & F in repairs CI soil, waste and vent pipe in any length with or without ears, with cement joints, laid in trenches or floors of 100 mm dia sand cast pipe complete all as specified and directed.

M&L for plain cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in bed to drain pipes of 100mm bore including packing under and haunching against sides of pipes after they are laid and tested. complete all as specified and directed.

S & F in repairs CI soil, waste and vent pipe in any length with or without ears, with cement joints, fixed to walls of 75 mm dia sand cast pipe complete all as specified and directed.

M&L concrete bed to 100 mm bore drain pipes in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregates including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed

S & F in repairs CI Bends (any radius ), diminishing pieces or tapers of 100 mm dia fitted with oval access door complete all as specified.

S & F in repairs CI Bends with access door (any radius ), diminishing pieces or tapers of 100 mm dia without oval access door complete all as specified.

S & F in repairs CI Bends (any radius ), diminishing pieces or tapers of 75 mm dia fitted with oval access door complete all as specified.

S & F in repairs CI Bends (any radius ), diminishing pieces or tapers of 75 mm dia fitted without oval access door complete all as specified.

S & F in repairs Cast iron branch pieces, Tee, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, 100 mm bore with cement joints, fitted with oval access doors complete all as specified and directed

S & F in repairs Cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, 75 mm bore with cement joints, fitted with oval access doors complete all as specified and directed

S & F 100 mm cast iron sanitary connections short connections pipe of length upto 300 mm complete all as specified and directed

S & F Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, for 100 mm bore pipes complete all as specified and directed

S & F Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, for75mm bore pipes complete all as specified and directed

Taking down rain water pipe (any size) or pattern incl all fittings, head shoes, bends swan necks etc incl cleaning or re-fixing or removal to store(measured overall as fixed along the centre line over fittings and accessories complete all as specified and directed

S&F for PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, of 110 mm dia complete all as specified and directed.

S&F for PVC (SWR) bends any radius 110mm dia bore complete all as specified and directed

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed

M&L for 15mm thick rendering with redimix plaster (as per manufacturer's instruction) on fair faces of brick work or concrete surfaces finished even and smooth surface without using extra on wall of internal surfaces up to four stories bldg complete all as specified and directed

M&L for 15mm thick rendering with redimix plaster (as per manufacturer's instruction) on fair faces of brick work or concrete surfaces finished even and smooth surface without using extra on wall and ceiling for external surfaces of up to four stories bldg complete all as specified and directed

M&L for 10mm thick rendering with redimix plaster (as per manufacturer's instruction) on fair faces of brick work or concrete surfaces finished even and smooth surface without using extra on ceiling of up to four stories bldg complete all as specified and directed

M&L for preparation of new plastered wall surfaces and applying two coats of cement base paint, white or tinted (colour and shade as per new colour scheme approved by GE) over a coat of primer of same make including scaffolding for four storey building complete all as specified and directed.

M&L for preparation of old decorated wall surfaces by complete removal of existing treatment and applying two coats of cement base paint, white or tinted (colour and shade as per new colour scheme approved by GE) over a coat of primer of same make including scaffolding for four storey building complete all as specified and directed.

M & L for Preparing new plastered or unplastered surfaces of wall and applying two coats of distemper oil emulsion, white or tinted over & including a coat of wall care Putty complete all as specified and directed

M&L for preparation by complete removal of existing treatment , wahsing down and stopping of distempered and painted surfaces and old plastered or unplastered surfaces of wall and applying two coats of distemper oil emulsion, white or tinted over & including a coat of wall care putty complete all as specified and directed

M&L preparing new plastered or unplastered surfaces of wall and applying three coats of white wash complete all as specified and directed

Complete removal of existing treatment , wahsing down and stopping of distempered and painted surfaces and preparing old plastered or unplastered surfaces of wall and applying three coats of white wash complete all as specified and directed

Demolition of brick work built in cement or cement lime mortar complete all as specified and directed

M&L brick work in CM (1:6) using sub class 'B' bricks, straight or curved on plan exc 6 mtr mean radius complete all as specified.

S&F 6 mm thick glass corner shelf (Single shelf) of best quility with CP steel railing of size (250mmx250mm) of best quality complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

M&L for MS hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

M&L for MS framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

Surface excavation in soft/loose soil, n.exc 30cm deep and averaging 15cm deep and getting out, complete all as specified and directed

M&L for 75 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate in sub base complete all as specified and directed

M & L Machine pressed pre cast concrete inter locking paver block 60mm thick M-35 grade with grey cement and pigment & glossy finished any shape colour, size complete all as specified and directed.

M&L for sand cushion under layer of floor complete all as specified and directed

M & L for removing excavated soils exc. 500m and and n. ecx 500 mtr depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed.

Cutting of trees including cutting of trunk n.exc 30cm girth and branches and digging out roots from floor or roofs and walls of up to four storied bldg and making good the dismantled portion in cement mortar 1:3 to match the existing surfaces complete all as specified.

S & F stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples

All as per Srl item No 137 here-in-before but as in repair after taking down old.

S&F as in repair for welding of 100mm size butt hinges medium wt cold rolled MS incl taking down shutter and refixing in same position and making good/functional incl supply of butt hinges complete all as specified and directed

Hacking out old broken glass of any size, thickness, quality or description from metal frame nexc 1.5 sqm each complete all as specified and directed

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exec 0.5 sqm each pane complete all as specified and directed

All as per Srl item No 141 here-in-before but figured glass pin headed type

S & F 40mm dia 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings for over flow pipe of PVC water tank including connection to tank fixed complete to walls, ceilings or in floors etc complete all as specified and directed

S & F 40 mm PP-R connection(Tank nipple) for water tank to overflow PP-R pipe 40mm dia complete all as specified and directed

S&F tank nipple GI 20mm bore complete all as specified and directed

S&F 20mm thick Gun-metal, globe or gate valves/ ball valve, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed

M & L for chipping of spalled and loose concrete and cleaning rust from re-inforcement by sand blasting scrubbing down concrete sufrace with wire brushes cleaning with water allowed to dry and applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bonding coat of approved epoxy adhesive on complete exposed surfaces of concrete to be gunited all as specified and applying two layers of guniting over and including steel welded mesh having 2 mm dia of wire and aperature 50mm, total thickness of gunite n.exc 25mm thick (average thickness) in cement mortar 1: 2 using OPC 53 grade cement mixed with polycrete admixture @ 2% by weight of cement or as per manufacturers instructions and finally applying cement plaster over gunite surface of required thickness to give even uniform and smooth finish conforming to proper geometrics in cement mortar ( 1 : 3) to match with the existing surface as in sides and soffits etc of slabs, chajjas,fins, facias, parapets, Lintels, columns and beams etc complete including necessary scaffolding, shuttering, necessary chases to brick work or RCC members at any height upto 4 storey bldgs including finishes as existing complete all as specified & directed

Demolition of RCC of any description, in any position roofs, floors (other than ground floors), beams staircases, landing, chajjas, RCC overhead tank and similar suspended work and Removing excavated material /demolition material exc. 1.50 km but n exc.5 km including taking down from upto four storey complete all as specified and directed

M&L for form work to chajjas and similar items including edges thick finished rough complete all as specified and directed

M&L for RCC 1 : 2 : 4 type B1 (using 20mm graded stone aggregate) as in chajjas complete all as specified

S&F 10mm dia TMT bar as in reinforcement of RCC of any description cut to length bent to shape required including cranking, bending, binding with MS wire not less than 0.90mm dia complete all as specified and directed

S&F 8mm dia TMT bar as in reinforcement of RCC of any description cut to length bent to shape required including cranking, bending, binding with MS wire not less than 0.90mm dia complete all as specified and directed

M and L for RCC 1 : 2 : 4 type A-1 (using 20mm graded stone aggregate) as in roof slab suported on wall beam and columns in floor slab complete all as specified and directed

M&L for form work to soffits of suspended slab such as roof slab and similar work not exc 200mm thick finished rough complete all as specified and directed

All as per Srl item No 154 here-in-before but edges of concrete slab

M&L for cutting holes into or through one brick thick brick walls built in cement mortar and making good in CM 1:3 or cement concrete 1:2:4 type B1 as required superficial area exc 400 sqcm but nexc 0.10 sqm round shape for exhaust fan etc. complete all as specified and directed

M&L cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in lintels upto 1.5 m clear span, cills, steps, coping, benching, roof kerb or mud stops, seismic and other similar bands, parapets and railings upto 60 cm in height, copings, apex stones, including form work to concrete surfaces complete all as specified and directed

Demolition & breaking up drain pipes (salt glazed stone ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe 150 mm complete all as specified and directed

M&L concrete bed to 150 mm bore drain pipes in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregates including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed

M&L 150 mm internal dia salt glazed stone ware drain pipes laid in trenches and jointed complete all as specified.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed

Removing excavated material /demolition material exc. 1.50 km but n exc.5 km and directed complete all as specified and directed

S&F in repair vitreous china semi pedestal pattern (Anglo Indian Type) wash down water closet pan, white including fixing bolts, connection to flushing cistern and flush & drain pipe (or outgoing pipe) and to flushing pipe, anti-syphonage pipe 'P' or 'S' trap etc complete all as specified and directed

S&F in repair plastic water closet seat, white closed pattern (seat cover for semi pedestal pattern) with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed

Description of Work / Item(s)

Amount

Taking down carefully the old U/S Aluminium point wiring (light, fan, socket or power) complete fitting such as switches, ceiling roses, pendants, sockets, regulators, etc and making good disturbed surfaces of walls including necessary touch up with the adjoining surface of disturbed area ie with OBD/colour wash/white wash as the existing finish complete all as specified and directed.

M&L point wiring with strandard copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable in but with through suitable concealed/surface PVC conduit and including replacement of modular sunken pressed steel terminal boxes 2mm thick required size and modular white cover plate with all accessories including 1.5 sqmm stranded copper conductor PVC unsheathed cable earth wire to common earth and connnected to earth dolly and making good to disturbed surface of walls including necessary touch up with adjoining surface of disturbed area i.e. with OBD/Colour wash /white wash as existing furnishes complete all as specified and directed. Note :- 1. The Rate is inclusive cutting/chasing and making good distrubed surface with CM 1:3 and same surface finishes with the adjoining surface of distribed area with ODB/colour wash/white wash complete. 2. At roof slab where there is burnt/blockage in the existing conduit wiring will be done through PVC conduit and rate are inclusive in the above quoted item. (a) All as per item No 2 but One light /fan/Bell point/security light controlled by one way switch

(b) All as per item No 2 here-in-before but One 3 pin socket outlet 5 amps on same board

(c) All as per item No 2 here-in-before but One 3 pin socket outlet 5 amps point independent board with cable 2.5 Sqmm for main current and 2.5 sqmm as earth wire as power point.

(d) All as per item No 2 here-in-before but One 3 pin socket outlet, 15 amps on independent board with cable 4 Sqmm for main current and 4 sqmm as earth wire as power point.

S&F switch modular type 1module 6 amps one way as per sample complete all as specified and directed

S&F socket outlet modular type 2module 2/3 pin, 6 amp as per sample complete all as specified and directed

S&F switch modular type 1 module, 16 Amps as per sample complete all as specified and directed

S&F socket outlet modular type 2 module combined shuttered, 5 pin 6/16 Amps as per sample complete all as specified and directed

S&F of electric bell ding dong AC, 230 volts single phase complete all as specified and directed

S & F in replacement of bell push, modular type 1 module 5/6 Amps as per sample complete all as specified and directed

S&F in replacement of Wall mounted LED Integrated Batten T5 20 Watt - 4Ft White, indoor decorative PVC extruded T5 LED battern-Integrated complete all as speficied and directed. Make Bajaj Cat Part No-BCLAB 20W WH LED P/ Crompton Cat Part No- LDL-20-CDL / Wipro Cat Part No-LL20-281-XXX-65AL1.

S&F in replacement of Wall mounted LED Integrated Batten T5 10 Watt-2 Ft White, indoor decorative PVC extruded T5 LED battern -integrated type complete all as speficied and directed. Make- Bajaj Cat Part No-BCLSB10 WH / Crompton Cat Part No-LCTLN-10-CDL / Havells Cat Part No-ENDURALINEARNEOBS10WLED865SPCWH.

S&F battan of holder PVC insulated body complete all as specified and directed

S&F in replacement of LED lamp 12 Watt LED Bulb complete all as specified and directed.

S&F of fan regulator electronic, modular type 2 module 4 steps as per sample complete all as specified and directed

Taking down of ceiling fan and keeping in safe custody and refixing it back after completion of point wiring complete all as specified and directed

S&F BLDC (Brushless DIrect Current) Ceiling fan, 1200mm suitable for regulator, not less than 350 RPM, not less than Air delivery 215 cum/minute, voltage 220V, hihg air follow with silence operation, having full copper winding & ribbed blade 3 Nos A/M blades. The BLDC motor fan shall have 100% rust free blade. The fan shall be BEE 5 star rating and compliant with IS-374 and making necessary electric connection of suitable PVC copper wire from ceiling rose to ceiling fan complete all as specified and directed including taking down old ceiling fan and depositing to MES store yard.

S&F in replacement of Wall mounting 12 Watt LED decorative wall light fixture made up of Polycarbonate, with suitable with all connection all as specified and directed.

S&F in replacement of 10 LED bulk head in engineering plastic housing with clear prismatic diffuser, 10W WHITE including all accessories connecting up twin core flexible copper conductor cable complete all as directed. Make- Havells Cat Part No – HEXAFT10WLED857SSYMBOPC / Crompton Cat Part No- LBHE-10-CDL / Wipro Cat Part No- WP1099

Taking down of exhaust fan and keeping in safe custody and refixing it back after completion of point wiring complete all as specified and directed at site.

S&F of ceiling rose surfaces bakelite minimum size 65x50mm with two/ three terminals complete all as specified and directed

S&F water storage heater 25 ltr capacity, 5 Star rated , vertical type, Glass line, AC, vertical type, AC, Single Phase electric, 230 Volt, complete with heating element, thermostat, 3 core lead, Plug top, safety valve, including electric and water connection with suitable nut, bolts & washers and making good to disturbed surface complete all as specified and directed

S&F PVC connection with brass nipple 15 mm x 600 mm long with ISI marked, stainless steel, suitable for hot and cold water of 25 ltrs capacity of geyser as hot and cold water connection complete all as specified and directed.

Taking down Electric/Electronic KWH meter and refixing it back after Submain wiring and connecting up complete all as specified and directed

S&F in replacement Sheet metal enclosure of size 300 x 250 x 150 mm suitable for mounting Single phase electric meter fabricated from 2mm thick CRCA sheet with anti corrosive dust and vermin proof. Note:- The meter cover shall have a fully transparent window. The window shall be of transparent, high grade UV stabilized engineering plastic for easy reading of all the displayed values/parameters and observation of operation indicator. The window shall preferably be an integral part of meter cover complete all as specified and directed

S&F in replacement of sheet metal enclouser V TPN 4 way MCCB 125A, 4P, Double door DB, IP-54 bus bar neutral link earth bar and din rail complete all as specified and directed

S&F in replacement of MCCB 125 Amps, 4 Pole, 415 Volts with 25 kA including electrical connection with bus bar or incomer with appropriate size of aluminium lugs and insulation packing complete all as specified and directed

S&F in replacement of MCB DB SPN 8 Way with metal double door, (IP43 Protection) flush mounting epoxy powder control having 100 Amps rated bus bar complete all as specified and directed

M&L in replacement MCB SPN 'B' curve 40 to 63 Amps 240 Volts , 10 KA complete all as specified and directed

M&L in replacement MCB SP 'B' curve 06 to 32 Amps 240 Volts complete all as specified and directed

M&L in replacement MCB SP 'B' curve 40 Amps 240 Volts complete all as specified and directed

S&F in replacement of LED Building security light fitting 40 Watt including fabrication of GI bracket 40mm dia suitable for fixing of LED light fitting duly fixed with clamps, nut, bolts, & washers etc complete all as specified and directed. Make – Crompton Cat Part No-LSTS-40-CDL-M / C Crompton cat part No-LSTS-40-CDL-M and Bajaj Cat Part No – BCLST30W LED

M&L for Earthing with galvanized steel earth plate 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate n.less than 1.5 m below normal ground level, connected to galvanized iron wire 4 mm as earthing lead by means of bolts, nuts, check nuts & washers of galvanized iron or steel besides building at all joints as shown in drgs and including excavation and earth work, GI pipe light grade 25mm bore of protection of GI wire from earth electrode, supply and laying charcoal dust, common salt, PCC (1:2:4) type B-1 Chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B-1using 20 mm graded stone aggregate Reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia , PGI funnel and wire mesh , 20 mm dia GI Pipe light grade for watering complete all as shown in drg and connected to earth test point including testing as directed by Engr-in-Charge.

M&L for submain wiring of two runs of 6 Sqmm size for main cable and one run of 6 Sqmm size earth continuity conductor of single core PVC insulated but unsheathed FRLS cable of specified size multistranded copper conductor 1100 volts grade IS-694 marked , drawn PVC conceiled conduit of size 25mm dia with complete all as specified and directed. Note : The rates are inclusive of Cutting / chasing and making good to disturbed surface with CM 1: 3 and same surface finishes with the adjoining surface of disturbed area with OBD/Colour wash /white wash complete.

M&L for sub main wiring using single run PVC FRLS grade insulated unsheathed, multistrand copper conductor cable 3 runs of 10 Sqmm for Phase and neutral and 1 run of 10 sqmm for earth wire drawn through suitable size of PVC concealed conduit complete all as directed by Engr-in-Charge. (Note :- Phase should be Red/Yellow/Blue, neutral should be black and earthing wire should be of green colour. Four runs of cable for 3 phase neutral and for earth will be measured and paid as one unit length) and making good a disturbed surface complete all as specified and directed

S&F metal body exhaust fan 300mm sweep, 230 volts with louver and copper wound including opening of hall and necessary electric connection with appropriate size of PVC copper wire from ceiling rose/switch board to exhaust fan including fixing of nut -bolts of suitable size and making good the disturbed surface of wall with OBD/white wash/colour wash to match with existing surface complete all as specified and directed

M/S Chhavi Constructions Co

Adhunik Builders

L G BUILDERS

VED PRAKASH ARORA

Shiv Shankar Nirman Co.

Shiv Shankar Nirman Co.

L G BUILDERS

ASSOCIATED CONSTRUCTION CO.

M/S Chhavi Constructions Co

Adhunik Builders

Adhunik Builders

L G BUILDERS

ASSOCIATED CONSTRUCTION CO.

M/S Chhavi Constructions Co

Shiv Shankar Nirman Co.

Bidder Name

Shiv Shankar Nirman Co.

L G BUILDERS

Adhunik Builders

VED PRAKASH ARORA

M/S Chhavi Constructions Co

ASSOCIATED CONSTRUCTION CO.