REPAIR REPLACEMENT TO CERTIAN BR WORK IN OFFRS JCOS ORS MD ACCN AND OTM ACCN UNDER AOR OF AGE BR I OF GE NORTH DELHI CANTT 10

Amount

Demolition of reinforced cement concrete (Reinforcement cut as required to facilatate demolition) of any description and in any position not otherwise specially provided

Demolition of plain cement concrete (unreinforced) of any thickness of any description and in any position not specifically provided for complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick joint free area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors over and inclding 15mm thick screed bed in cement mortar 1:6 set and jointed in neat cement slurry and pointed in coloured cement & including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed.

All as per the description of ser item No 03 but in vertical surface as skirting, dado and risers to steps over and including 10mm thick rendering/backing coat in cement mortar 1:4 all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors over and inclding 15mm thick screed bed in cement mortar 1:6 set and jointed in neat cement slurry and pointed in coloured cement. including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface area of each tile 0.07 to 0.15 Sqm each set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including rendering 10mm thick in CM (1:4) and finished rough, complete including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed.

M&L for 3D exterior designer coloured matt finished wall tiles 300 x 600mm design as approved over and inclding 10mm thick rough finished rendering in cement mortar 1:4 including taking down and removal from site complete all as specified and directed

M&L for double charged vitrified coloured tiles shade as approved 10mm thick (square/rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 1.0 sqm, in floors, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and inclding screed bed or bedding layers of mortars 15mm thick in CM 1:6 and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed. all as specified and directed

All as per for the description of srl item No. 8 above but as in vertical surfaces such as skirting/ dado over and including 10mm thick rendering in CM (1:4) compelete.

M&L for 75mm thick 1:4:8 type-D-2 (using 40mm graded crushed stone aggregate) as in sub base to receive stone slab and pavement all as specified and directed.

M&L 20 to 25mm thick pre-polished machine cut Kota stone slab as in flooring over and including 15mm thick screed bed in cement mortar 1:6, laid over cement slurry @ 3 Kg/Sqm and jointed with grey cement slurry mixed with pigment to match with shade of slab including molding the edge of slab complete all as specified and as directed. Note:- The size of Kota stone slab shall not less than 550mm x 550mm cut size in flooring and full length single piece in steps, except the location where the balance portion remain less than size as specified above.

M&L 20 to 25mm thick pre-polished machine cut Kota stone slab as in riser or vertical surface over and including 10mm thick rendering in cement mortar 1:4, and jointed with grey cement slurry mixed with pigment to match with shade of slab including molding the edge where as specified and as directed. Note:- The size of Kota stone slab shall not less than 550mm x 550mm cut size as in flooring and full length single piece in steps, except the location where the balance portion remain less than size as specified above.

M&L for old size brick work with fly ash bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 including demolition of brick work all as specified and directed.

Taking down existing cement plaster or complete removal of existing pointing and finishes including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L 15mm thick ready mix plaster (Make Ultratech readiplast/ Birla Aerocon RMP/ ACC Suraksha RMP) on brick work on concrete surface of wall (internal surfaces) finished even and smooth all as specified and directed by GE.

M&L 15mm thick ready mix plaster (Make Ultratech readiplast/ Birla Aerocon RMP/ ACC Suraksha RMP) on brick work on concrete surface of wall (external surfaces) finished even and smooth all as specified and directed by GE.

M&L 5mm thick ready mix plaster (Make Ultratech readiplast/ Birla Aerocon RMP/ ACC Suraksha RMP) on ceilling surfaces finished even and smooth all as specified and directed by GE.

M&L for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparing old decorated plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed

M&L for preparing new plastered surfaces of wall and applying two coats of oil bound distemper white or tinted over and including a coat of 2mm wall care putty and chalk whiting on plastered surfaces preparatory to distempering complete all as specified and directed

M&L for complete removal of existing treatment and preparing old decorated surfaces of wall and applying two coats of Oil Bound Distemper over a coat of 1mm wall care putty complete all as specified and directed

M&L for preparation of new plastered surfaces of wall and applying two coats of cement based paint over a coat of cement primer complete all as specified and directed

M&L for complete removal of existing treatment of wall including cornices etc. by washing, rubbing down and stopping holes, and applying two coats of cement base paint over one coat of primer of approved shade complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not other wise provided all as specified and directed

S&F steel water tubes, medium grade, ISI marked, galvanised, 15mm bore with all fittings, fixed to walls and ceiling or laid in floors including taking up or down steel tubing and connections complete all as specified and directed

S&F steel water tubes, medium grade, ISI marked, galvanised, 20mm bore with all fittings, fixed to walls and ceiling or laid in floors including taking up or down steel tubing and connections complete all as specified and directed

Refixing only old 15mm dia bore steel water tubing & connection in new or old position fixed to wall, ceiling or laid in floors including necessary cutting & making of new threads for fixing of new fittings such as elbows, tees, sockets, union, , reducer, etc as required including taking up or down steel tubing and connections complete all as specified and directed .

Refixing only old 20mm dia bore steel water tubing & connection in new or old position fixed to wall, ceiling or laid in floors including necessary cutting & making of new threads for fixing of new fittings such as elbows, tees, sockets, union, , reducer, etc as required including taking up or down steel tubing and connections complete all as specified and directed

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings or conduit wiring, etc and making good, cutting not exceeding 10cm girth complete all as specified and directed

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floor 75mm bore including demolition/taking down PVC/CI drain/Rain water pipe complete all as specified and directed

S&F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.50 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

S&F in repairs sheet Glass shelf assembly consisting of 5.5mm thick sheet glass self 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed

S&F in repairs 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate mix with WPC complete all as specified and as directed.

S&F in repairs bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed

S&F in repairs brass CP mixer/wall mixer for mixing hot & cold water screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore including connection pipe and fittings complete all as specified and directed .

S&F in repairs 10 litre capacity PVC low level flushing cistern with dual flush type‘ white’ with inlet, float valve including bracket with 32mm dia PVC waste/flush bend pipe appx 600mm long complete all as specified and directed

S&F in repairs PVC connection 600mm long and15mm dia with brass fly nut at both ends complete all as specified and directed

S&F in repairs vitreous china squatting pan, ‘Orissa’ pattern, of size 580mm x 440mm white with integral foot rest complete including trap and plain cement concrete bedding, outgoing flushing pipe, anti syphonage pipe etc complete all as specified and directed

S&F in repairs Chromium plated brass angle valve concelled type for 15mm bore pipe, fixed in repairs complete all as specified and directed.

Taking down chowkhats or frames n.exc 1.50 sqm with shutters (without taking off shutters from the frames) all as specified and directed.

Taking down chowkhats of frames exc 1.50 sqm but n. exc 4.0 sqm with shutters (without taking off shutters from the frames) all as specified and directed.

Taking down door shutters of any description exc 1 Sqm & n.exc 2 Sqm each complete all as specified and directed

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 70mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with meter joints after applying PVC solvent cement and screwed with fullbody threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)complete all as specified and directed.

S&F factory made double rebated extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 65 x 125mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge. Note: For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made

Providing 30mm thick FACTORY-MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, Door to be panneled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of GE, manufacturer's specification & drawings.” Note: Fixture/fittings shall be measured & paid under relevant item except meshe

S&F aluminium window as per TD drg No. CEDZ/TD-316 with following specifications :- (i) Outer frame of size 40mmx114mm with 1.3mm thickness, corner 45 degree cut & aluminium welded. (ii) Center mullion of size 40mmx65mm. (iii) Welded shutter (02 Nos) of size 40mmx60mmx1.3mm thickness 45 degree cut mechanically joint with 6mm allen key bolt clamp with 5mm clear glass both side EPDM rubber gasket metal body hand lever type single point lock, aluminium kobra hinges 2 Nos per shutter. (iv) 12mm SS 202 grade round bar safety grill at 100mm cc distance modified to 150mm cc distance in front of handle, welded at both ends with 6mm SS 202 grade round bar. (v) Welded wiremesh shutter (2 Nos) of size 40mmx18mmx1.3mm thickness 45 degree cut with 0.45mm nominal dia of SS wire mesh, SS 75mm long hinges & PVC magnet. (vi) Entire window shall be powder coated with pure polyster coat of any shade as approved by GE. (vii) Window shall be installed with silicone complete all as specified and directed by GE.

S&F aluminium window as per TD drg No. CEDZ/TD-316 with following specifications :- (i) Outer frame of size 40mmx114mm with 1.3mm thickness, corner 45 degree cut & aluminium welded. (ii) Center mullion of size 40mmx65mm. (iii) Welded shutter (02 Nos) of size 40mmx60mmx1.3mm thickness 45 degree cut mechanically joint with 6mm allen key bolt clamp with 5mm clear glass both side EPDM rubber gasket metal body hand lever type single point lock, aluminium kobra hinges 2 Nos per shutter. (iv) 12mm SS 202 grade round bar safety grill at 100mm cc distance modified to 150mm cc distance in front of handle, welded at both ends with 6mm SS 202 grade round bar. (v) Welded wiremesh shutter (2 Nos) of size 40mmx18mmx1.3mm thickness 45 degree cut with 0.45mm nominal dia of SS wire mesh, SS 75mm long hinges & PVC magnet. (vi) Entire window shall be powder coated with pure polyster coat of any shade as approved by GE. (vii) Window shall have provision for installation of window AC/Desert Cooler and provision of window glass shutter, wiremesh, grill and necessary fittings and locking arrangements for subject portion will be modified as per ground requirement during the execution as per directions of GE. (viii) Window shall be installed with silicone complete all as specified and directed by GE.

S&F flush shutters 30mm thick, solid core construction, with block board core and ply wood face panels, commercial type on both sides with leaping and beading complete all as specified and directed

Mild steel conforming to Fe 410-0 or Fe 310-0 in framed work such as grills, gratings, door frame etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified and directed

S&F mild steel, plain, black sheet of 1.60mm thick in wall cladding steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up mitred angles etc as required complete all as specified and directed

Taking down/dismantling old particle board or any board kitchen cabinet with wardrobe including fillets and making good disturbed surfaces all assessary complete all as specified.

S&F factory made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Board of required size comprising of virgin PVC resin of K Value 57-60 (Suspension Grade), Calcium Carbonate and natural Fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives, made froms Extrusion process WPC foam sheet Single Extruded (Inner) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity (Screw Withdrawal strength of 2000 N (Face) & 1100 N (Edge), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of GE, Material test certificate and authentication should be compulsory provided by the manufacturing company: For WC/Bathroom/Toilet/Kitchen & Cabinets.”

S&F factory made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 (Suspension Grade), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet. Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive strength of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of GE, Material test certificate and authentication should be compulsory provided by the manufacturing company: For WC/Bathroom/Toilet/Kitchen and Cabinets.

S&F magnetic catches with steel body ‘H’ type, fixed to shutter complete all as specified and directed.

S&F continuous (piano) hinges of width 30mm when open flap), mild steel, bright finish or electrogalvanised

S&F 100mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed

S&F 4 levers brass cupboard locks grade-I, size 65mm complete all as specified and directed

S&F 150mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed

S&F 200mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed

S&F butt hinges, 100mm size medium weight, cold rolled mild steel complete all as specified and directed

S&F aluminium handles 150mm size cast type, anodised complete all as specified and directed

S&F 300mm aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete all as specified and directed

S&F stainless steel chromium plated tubing of 25mm dia curtain rod fancy type including fancy type CP brabs brackets (wall to wall or flush to wall) with finials or end caps decorative type as approved by GE for securing to curtain rod to wall in position, fixed in repair complete all as specified and directed

M&L for applying two coats of synthetic enamel paint on new wooden surfaces of any description over 10cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and directed

M&L for applying two coats of synthetic enamel paint on new steel surfaces of any description over 10cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete all as specified and directed

M&L for two coats of synthetic enamel paint on old steel painted surfaces including preparation of surfaces of any description not otherwise descriped over 10 cm width or grith complete all as specified and directed.

M&L for two coats of synthetic enamel paint on old wooden painted surfaces including preparation of surfaces of any description not otherwise descriped over 10 cm width or grith complete all as specified and directed.

M&L for 40mm thick plain cement concrete 1:2:4 type B-1, (20mm graded aggregate) as in floors and finishing cement concrete surface even and smooth with using extra cement complete all as specified and directed

M&L cement concrete 1:3:6 type C-1, (using 20mm graded crusted stone aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair without using extra cement including making joints at every 2.5m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight including necessary form work and complete all as specified.

Removing of existing water proofing membrane, damage plaster, vegitation/plants, PCC, mud fuska, tar-felt, loose particles and all forgin materials over the roof and shifting the debris from site to out-side area as directed by authority on factory garbage area Crusted

Dismantling of floor of size not exceeding 1.50 Sqm mtr for water closet/bath and removing out the cinder/concrete from sunken portion, grinding any sharp edges etc all as specified and directed with following: (a) Cleaning of RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (b) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite. (c) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified. (d) M&L for providing 40mm dia GI pipe spout projecting at least 150mm beyond outer face of wall. (e) M&L for sunken portion filled with 40mm graded brick bats and finished with 50mm thick PCC 1:2:4 type B1 all as specified and directed. (f) The area of Each WC portion is n.exc 1.50 Sqm each. (g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. (h) 72 hrs Ponding test shall be carried out for sunken treatment before payment.

Cleaning the surface & removing of dust, existing paints from wall & roof surface, finding visible crack Making V - Groove by machine on crack area, providing & applying Polymer Bonding agent (1:2) & filling those grooves by modified cement & sand mortar (1:4) with WPM liquid (5% by wt. of cement). Waterproofing coating-Providing & applying 1st coat WPM with brush/roller after mixing with cement at 1:1.5 (1 part ofand 1.5 part of cement & 2nd coat with an interval of 10 to 12 hrs by brush or roller to get average thickness of 1.5 mm. The system will be allowed to air cure for 7 days covering including parapet both side wall complete all as directed. Note - Wk to be executed through authorised applicator.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded crusted stone aggregate as in string courses copings or as floors complete all as specified and directed

M&L for preparation of new or old plastered surfaces of wall and applying two or more coat of 100% Premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489;2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over new surface complete all as specified and directed

Providing & fixing false ceiling with semi perforated 12mm thick micro tegular edged at all heights with GRG (glass fibre reinforced Gypsum ) false ceiling tiles of size 595X595mm of approved texture, design and pattern having moisture content less than 2% , humidity resistance of 99% ,NRC0.50 to 0.75 as per IS 8225:1987 , Non combustible as per BS 475 (part-4)-1970 and light code Description unit rate No. 429 SUB HEAD : 26.0 NEW TECHNOLOGIES AND MATERIAL reflectance of 85% minimum to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanised @ 120 gms per sqm including both sides ) comprising of main-T runners of size 15x32mm of length 3000 mm,gross-T of size 15X32mm of length 1200 mm and secondary intermediate cross-T of size 15x32 of length 600mm to form grid module of size 600x600 mm, suspended from ceiling using galvanised mild steel items(galvanising @ 80 gms per sqm ) i.e. 50mm long , 8mm outer diameter M-6 dash fastners , 6mm dia fully threaded hanger rod upto 1000mm length and L shaped level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fxed on perimeter wall/partition with the help of plastic rawl pluhs at 450mm center to center and 40mm long dry wall screws . the work shall be carried out as per specification, drawing and as per direction of the GE.

M&L for 15mm thick cement plaster on surfaces of concrete in CM 1:4 on roof surfaces (Over PCC Padding) mixed with WPC @ 200 ml par 50 Kg of cement bag complete all as specified and dierected. Note : WPC shall be measured and paid separately

Supply only liquid water proofing compound complete all as specified and directed

S&F in repairs with complete installation of wind operator turbo air ventilator of size 600mm dia made of stain less steel sheet including dual ball bearing fixed over assembly made of polycarbonate transparant sheet of size 5.5 x 3.5 feet on roof of steel structure shed working height up to 15 meter all as specified and directed by GE.

Supply only steel wheel sutaible for sliding steel door shutters on top or bottom rail including bush or ball bearing and all consumable items for making operational complete all as specified and directed

S&F steel rolling shutters, gear operated type with bevel gear box and crank handle without ball bearing as specified including top covers anchoring rod, hasp & staple and one shop coat of red oxide primer and errected in position including taking down complete thickness of laths 1.25mm complete all as specified and directed.

S&F safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed

Supply only mild steel helical wire spring 45cm long , 75mm dia and weighting of each spring not less than 3.00 kg complete all as specified and directed

S&F for ball bearing for rolling shutters make as approved all as specified and directed.

The new hut furnitures (BID ID -3304331)

QUALITY CONSTRUCTIONS CO (BID ID -3304558)

M/S SURINDERAS CONSTRUCTION CO. (BID ID -3310215)