REPAIR/REPLACEMENT OF UNSERVICEABLE STREETLIGHTS FITTINGS/ SECURITY LIGHTS AND ALLIED WORKS IN MAHAR, FD HOSP AND REPAIR/REPLACEMENT OF LED SECURITY LIGHTS AND STREET LIGHTS AND OTHER CONNECTED ITEMS IN CENTRAL AMENITIES, CWE OFFICES, GE DIPATOLI ,

Amount

M & L Attending day to day Street light/bldg security light/High mast light complaints (Street lights /building security light /Hight mast light fitted on poles/buildings at height up to 10-20 mtr from ground level), repair/replacement of unserviceable accessories like LED driver, acrylic covers, nuts, bolts, GI clamps,GI Bracket,cables, wires, MCB's, earthing, earthing strip, earth wire, Feeder Pillar, MCB, MCCB's, bus bars, HRC fuses, rewirable fuses, contactor, timers, connector, wires, cables glands, thimbles etc and making the street light fully functional complete all as per the instruction of JE E&M / Engineer in Charge including excavation,returning filling,removing and cost of Tower wagon, cable fault locator equipment and all required tools, ladders, safety belt, labour and all other incidental operations required for execution of street light light maintenance work are included for smooth operation. Note: - (i) Cost of spares and accessories will be measured and paid seperatly under relevent items. (ii) Cost for taking down and re-fixing new parts shall be deemed to be included in the unit rate quoted. (iii)Recovery shall be made from Contractor @ Rs. 50/- per complaint/ Hours, if he fails to attend and rectify the complaint within 48 hours of lodging the complaint either personally / telephonically/Email. In this regard the decision of the Engr-in-Charge shall be final & binding.

Dismantling and taking down old unserviceable street light fitting/bldg security light fittings/High Mast Light fitting/Post top laltern of any capacity from upto 20 mtr height of pole /wall incl disconnecting the cable connections complete all as specified and directed.

Disconnecting electrically and taking out unserviceable nature switch box, feeder pillar box any type and size and removing material from site including making good of disturbed surfaces complete all as specified and directed.

Taking down carefully copper/aluminium wiring of size 1.5/2.5 sqmm from surface at any height of pole and removing the materials from site and making good the disturbed surfaces etc complete all as specified and directed.

Taking down XLPE cable and high mast cable from any height of pole and removing the materials from site and making good the disturbed surfaces etc complete all as specified and directed.

S & F Pressure die cast aluminum alloy housing LED street light fitting 60 Watt comprises of pressure die cast Aluminium housing & having system efficiency 110 lumens/Watt i.e 6670 lumns,All LEDs should be highpower LEDs of 1W to 3W Only with moduler lens for batwin shape distribution of 30 degree & 60 degree,Input voltage working range is 140 Vac to 270 Vac,Brand name should be emoboised,Potted Driver is used with 4KV internal & external 5KV Potted surge protection,Short Circuit Protection,Open Circuit Protection,High & low voltage protection,fixture should withstand high & low voltage protection,fixture should withstand high voltage upto440 v for 8 hr,IP66 Protected,THD<10%,CRI>70CCT 5700+/-300K, PF>0.9, Driver efficiency>85%,LM79 report require from NABL Accediated lab all as directed by Engr-in-Charge. Make : Crompton cat part No. LSTP-72-CDL-M or equivalent in Jaguar /Philips.

S & F Pressure die cast aluminum alloy housing LED street light fitting 90 Watt comprises of pressure die cast Aluminium housing & having system efficiency 110 lumens/Watt i.e 6670 lumns,All LEDs should be highpower LEDs of 1W to 3W Only with moduler lens for batwin shape distribution of 30 degree & 60 degree,Input voltage working range is 140 Vac to 270 Vac,Brand name should be emoboised,Potted Driver is used with 4KV internal & external 5KV Potted surge protection,Short Circuit Protection,Open Circuit Protection,High & low voltage protection,fixture should withstand high & low voltage protection,fixture should withstand high voltage upto440 v for 8 hr,IP66 Protected,THD<10%,CRI>70CCT 5700+/-300K, PF>0.9, Driver efficiency>85%,LM79 report require from NABL Accediated lab all as directed by Engr-in-Charge. Make : Crompton cat part No. LSTP-90-CDL-M or equivalent in Jaguar /Philips.

Supply & Fix LED flood light ftg 120 Watts , Incl Driver unit assy with surge protection,Short Circuit Protection,Open Circuit Protection,High & low voltage protection,fixture should withstand high & low voltage protection,fixture should withstand high voltage upto440 v for 8 hr,IP66 Protected, Make : Crompton Cat part No LFNL-150-CDL/60-M or equivalent in Havells /Philips

Supply & Fix LED flood light ftg 150 Watts , Incl Driver unit assy with surge protection,Short Circuit Protection,Open Circuit Protection,High & low voltage protection,fixture should withstand high & low voltage protection,fixture should withstand high voltage upto440 v for 8 hr,IP66 Protected, Make : Crompton Cat part No LFNL-150-CDL/60-M or equivalent in Havells /Philips

Supply and fix in replacement post top lantern cast aluminium spigot,spun aluminium canopy with clear acrylic cover with 20 Watt LED lamp including all accessories such as Bracket,GI Pipe and prewired complete all as specified and directed at site. Make : Bajaj /Havells/ HPL

Nature Switch street light controller three phase 5 KW of automatic street light switch using infrared sensor based NATURAL SWITCH for automatic switching of street lights, required illuminance for switching on is ≤30 Lux and for switching off ≥10 Lux also having part night operation 4 to12 hour with contactors and outgoing and incoming MCBs connected with min 10sqmm FLRS multistranded circuit all these must be enclosed in a pole/wall mounted enclosure made of rust proof, electric shock proof and termite proof conforming to IP54 complete all as specified and directed by engineer in charge

S&F power conactor type 1P auxilary contact 1NO 1 NC coil voltage 230V AC,32 A, 50 HZ suitable for timer switch of street light complete all as specified and directed complete all as specified and directed at site. Make : L&T/Schneider/Siemens

Supply,laying,jointing,testing and commissioning XLPE insulated,armoured,heavy duty, LT UG cable with aluminium conductor,1100 volts grade cross sectional area 16 sqmm 4 core connected with aluminium lugs connected by cramping tools complete all as specified and directed at site by Engr-in-charge. Note:- Excavation and earth work will be measured and paid separately.

Supply,laying,jointing,testing and commissioning XLPE insulated,armoured,heavy duty, LT UG cable with aluminium conductor,1100 volts grade cross sectional area 10 sqmm 4 core connected with aluminium lugs connected by cramping tools complete all as specified and directed at site by Engr-in-charge. Note:- Excavation and earth work will be measured and paid separately.

M & L Unsheated 5 core of 6 sqmm insulated, Unarmoured, heavy duty electric cable with Copper conductor, 1100 Volts grade suitable for High Mast light, all as directed by Engineer-in-Charge. Make: Havell's/Poly Cab/RR cable

Supply,laying,jointing,testing and commissioning PVC tape/Extruded innersheathed Aluminium unarmoured service wire, 650/1100 volts grade cross sectional area 10 sqmm 4 core connected with aluminium lugs connected by cramping tools all as specified and directed at site.

Taking down/dismantling LT PCC/steel tubular poles ,studs,insulator including V clamp,cross arms , earth wire support etc and deposit to MES store complete all as specified and directed at site by Engr-in-charge.

M&L Steel tubular swaged poles complete with cast iron base plate,finial taper plug,bolts,nuts & screws as specified type 410 SP-31 ( 9.00 Meters long) complete all as specified and directed at site.Note : Excavation ,earth work & PCC work shall be measured paid separately.

M&L for trenchless boring under road crossings/foot paths by manual / Boring machine complete all as specified and directed at site.

Supply and fix in replacement of 50 mm bore GI pipe light grade fixed on pole /trenches/wall/road crossing etc complete with clamp nut bolt etc all as specified and directed at site.

Excavation in trenches in soft/loose soil n.exc 1.5 mtr wide and n.exc 1.5 mtr depth and getting out for foundation ect. Or for shafts, well, cesspits, mainholes ect. In any type of soil for foundation and getting out and levelling of bottom surface to required level all as specified and directed by engineer-in-charge

Excavation in trenches not exceeding 1.5 mtr wide and depth beyond the first 1.5 mtr for foundation ect. Or for shafts, well, cesspits, mainholes ect. In any type of soil for foundation and getting out and levelling of bottom surface to required level all as specified and directed by engineer-in-charge

Supply and providing sand cushioning with dry clean sand 15 cm below cable and 8 cm above the cable and punning the sand complete all as specified and directed by Engr-in-charge. Note : Punned thickness shall be measured for the purpose of payments.

Supply and laying burnt bricks old size sub class-B laid in trenches for cable protection with length of brick perpendicular to length of cable complete all as specified and directed.

Removing surplus excavated material not exc 50 mtrs and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed.

Demolition of cement concrete in ground floor and paving built in cement concrete (unreinforced) n.exc 15 cm thickness (below or above ground level) complete all as directed..

M&L for PCC (1:2:4) type B1 using 20 mm graded stone aggaregate in kerbs/coping /bed plates and like including weathering slightly rounded or chamfered complete with necessary use and waste fo form work complete all as specified and directed at site.

M&L for PCC (1:4:8) type D2 using 40 mm graded stone aggregate in foundation mass concrete and filling including weathering slightly rounded or chamfered complete with necessary use and waste fo form work complete all as specified and directed at site.

Dismantling cross- arms of MS ,channel or angle sections & Earth Wire etc complete all as specified and directed at site.

Supply fixing and fabricating tray holding cross arms FI clamps support U clamps strips and back plates fabrication from structural steel section incl nut bolts washer bars etc of required size and thickness for supporting of cable tray by welding incl bending or welding cold or hot,drilling holes for bolt in any shape or size indicated or included of one coat primer coat under one finishing coat of black paint complete to support the cables all as specified.

Supply and fixing in replacement of street light cable junction box of size 155x155x100 mm with terminals fixing on pole with 25x4 mm aluminium strip clamp with nut,bolts and washer etc Make : Hensel or equivalent as per list of makes

S&F in replacement service bracket for street light fitting made out of 40 mm bore light grade GI pipe of length 1.5 mtr long (approx) bend to shape 115 degree and fix to pole for fixing of street light fitting on pole/wall etc fixed with 2 Nos 32x 6 mm GI clamp, Nut,bolts,washer etc complete all as specified and directed.Make:JINDAL/BST/TATA

Supply and fix 1.5 Sqmm, single core Two runs PVC insulated and unsheathed FR cable 1100 Volts grade with multistranded copper conductor and one run of 1.5 Sqmm cable for common earth dolly drawn through heavy duty PVC conduit for street light pole including connection from kiosk box to street light fittings complete all as specified and directed. Make- Polycab/Havells/Anchor

All as per ser item No.34 here-in-before but 2X 2.5 Sqmm and 1X 2.5 Sqmm for Earth wire complete all as specified and directed. Make- Polycab/Havells/Anchor

Supply only single core copper conductor PVC insulated unsheathed FR 1100 Volt grade 1.5 Sqmm size,multistranded unsheathed complete all as specified and as directed. Make : Polycab/Havells/Anchor

Supply only LED driver unit suitable for 60 watt LED Fitting complete all as specified and directed at site.Make : Havells /Jaguar/HPL

Supply only LED driver unit suitable for 90 watt LED Fitting complete all as specified and directed at site.Make : Havells /Jaguar/HPL

Supply only LED driver unit suitable for 120 watt LED Fitting complete all as specified and directed at site.Make :Havells /Jaguar/HPL

Supply only MCB SP 06 to 32 Amp 10 KA, 'C' curve 230 Volt complete all as specified and directed at site.Make : Havells Cat Part No.DHMGCSPF006-032 or equivalent in Schenider/Legrand

Supply only MCB DP 63 Amp complete all as specified and directed at site.Make : Havells Cat Part No.DHMGCDPF063 or equivalent in Schenider/Legrand

Supply only Heavy duty PVC Non metallic conduit of external dia 20 mm complete all as specified and directed at site.Make : Anchor/Polycab/Plaza

M &L for GI Earthing complete with GI earth plate electrode 60cm x 60cm x6 mm buried directly in ground verticvally to size of depth not less than 0.90x 0.60 x 2.25 mtr below ground level with top edge of the plate at a depth not less than 1.5 mtr below ground level, earth plate connected to galvanised earth strip of size 25x4 mm, 7.5 mtr long by means of brazing nuts, bolts, check nuts, & washers ,testing of completion (drawn in earth lead protection pipe light gade GI of size 32/40 mm dia) by means brazing at both edges with vertical plane of electrode all as shown in plate No 3 of SSR Part - I connected to earthing lead with Main switch/main control board,filling with charcoal dust, and common salt, including necessary excavation and earth work in any type of soil ,perforated watering pipe,funnel with wire mesh,earth lead protection pipe light grade PCC chamber 1:3:6 type C1 (for even finish on both the faces) and RCC cover 1:2:4 Type B1,450 x450 x50 mm thick with 6 mm dia CTD bars 150 mm c/c with 2 Nos of handles of 10 mm dia steel rod all as specified and directed and testing on completion and connected to equipment with lugs and screw nuts etc all as specified and directed by EIC Note : (i) 7.5 RM GI earth wire deemed to be included in quoted rates beyond 7.5 RM wire shall be measured and paid separately. (ii) Earth resistance of earth pit should be not more than 02 Ohms on testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost. (iii) Rate quoted by the tenderer is deemed to included salt & Charcoal upto & above 450 mm top of GI Plate.

S&F GI strip of size 25x4 mm connected both ends with necessary bolts, nuts & washrs complete all as specified and directed.

M&L for painting of LT poles 9 mtr with synthetic enamel paint upto 2 mtr height with black and white paints with two coats and painting of cross arm/channel/clamp and street light bracket with aluminium paint incl making good to receive the paint incl base paint strips with synthetic enamel paint of approved colour all as shown complete all as specified and directed by EIC.

Material and labour for painting to existing LT steel tubular poles of sizes 9 mtr including bracket and other accessories as per site requitrement after preparing/ scraping the metal surface with emery sheet in all respect for making smooth surface and painted with one coat coat of aluminium paint including writing pole No/ feeder No and supply and fix of superior quality self adhesive water proof photo reflective tape in two lines on poles as directed (tape size and tint shall be as approved by Department) as per site requirement complete all as specified as directed.

Supply only copper wound Ballast 250 watt 230 volt suitable for 250 watt MH/SV lamp complete all as specified and directed at site.Make : Havells orequivalent in Crompton/Philips

Supply Metall hallide lamp 250 watt E-40, 230 volt complete all as specified and directed at site.Make : Havells or equivalent in Crompton/Philips

Supply only T-5 electronic ballast suitable for 2x24 watt Fitting, complete all as specified and directed at site.Make : Havells or equivalent in Crompton/Philips

Supply Only T-5 FTL 24 watt 230 volt, suitable for 2x24 /4x24 Watt fitting complete all as specified and directed at site.Make : Havells or equivalent in Crompton/Philips

Supply only CFL 4 pin 36 watt 230 volt, 2 ft long complete all as specified and directed at site.Make : Havells /HPL/ Crompton

Supply and fix in replacement garden light 10 Watt lantern cast aluminium tripod type LED Bollard with soft 360 deg with clear acrylic cover with LED lamp complete all as specified and directed at site. Make : crompton /Havells/ HPL

Supply only LED driver unit suitable for 150 watt LED Fitting complete all as specified and directed at site.Make :Havells /Jaguar/HPL

Supply only Heavy duty PVC Non metallic conduit of external dia 20 mm complete all as specified and directed at site.Make : Anchor/Polycab/Plaza

m/s sheo kumar singh & sons

M/s Ray construction

A P ENTERPRISES

M/S ABHAY KUMAR AND BROTHERS

M/s Deepak kumar sinha

M/S CHAUHAN CONSTRUCTION

Associated Engineers