PROVN OF TILING IN KITCHEN IN BLDG NO P 45 (SIX QUARTERS) P 48 (TWO QUARTERS JCOS FAFA OF ARC HAPPY VALLEY SHILLONG AND PROVN OF RETAINING WALL IN FRONT OF BLDG NO S 23 (RECORDS OFFICE) OF ASSAM REGIMENT CENTRE AND PROVN OF 2 X ELEVATED SENTRY POST B

Amount

AGE B/R SCHEDULE PART - I Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section, in any position as in unframed or framed work complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, Including removal of debries out side MD land all specified and directed.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for providing Hardcore of gauge n exc. 63 mm size broken stone or boulder, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry type C1 , 1:3: 6, 20mm graded stone aggregate with solid blocks, exc. 10 cm in width and setting in mortar 1:6 , complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 ( Using 40mm graded agg) as in foundation , flooring work and mass concrete complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 ( 12.50 mm graded aggregate) as in levelling course of tile flooring etc. complete all as specified and as directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including 15 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes finished fair and even complete all as specified and directed.of tile complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 sqm, such as skirting, dado, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tiles including 10mm thick rendring in CM (1:4) on fair faces of brick or concrete surfaces finished fair and even on vertical surfaces of wall complete all as specified and directed.

M&L for glazed ceramic coloured tiles 300 mm X 200 mm X 7 mm thick as on vertical surface of wall such as skirting, dado, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tiles including 10mm thick rendring in CM (1:4) on fair faces of brick or concrete surfaces finished fair and even on vertical surfaces of wal complete all as specified and as directed.

M&L for 10 mm thick plaster in cm (1:6) on fair faces of brick or concrete surfaces and finishing even & smooth without using extra cement complete all as specified.

M&L for rendring 15 mm thick plaster in cm (1:4) on fair faces of brick work or concrete surfaces including finishing even & smooth without using extra cement complete all as specified.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for preparation of new plastered/concrete surfaces of walls, providing one more coats of Birla white wall care putty to achieve smooth surfaces and applying two coats of Oil Bound Distemper of approved shade/tint over a coat of compatiable priming paint complete all as specified.

Excavating in trenches in soft/loose soil, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out.

All as per items No 18 above herein but for hard/dense soil.

Returning and filling including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft / loose soil complete all as specified and as directed.

Removing excavated materials (soil) n.exc. 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as direted.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.06 Sqm but not exc. 0.11 sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including 15 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes finished fair and even complete all as specified and directed

M & L for glazed ceramic coloured tiles 300 mm X 450 mm X 7 mm thick as on vertical surface of wall such as skirting, dado, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tiles including 10mm thick rendring in CM (1:4) on fair faces of brick or concrete surfaces finished fair and even on vertical surfaces of wall including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and as directed.

M & for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar 10mm thick in (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L for rounding to edges of stone slabs one edge, such as in steps cooking plateform, and other similar situation complete all as specified and as directed.

M & L for Reinforced cement concrete type-A1, 1:1.5:3 (20mm graded stone aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M & L for Reinforced cement concrete, type-A1, 1:1.5:3 (20mm graded stone aggregate) Columns, pillars, piers, posts and struts complete all as specified and as directed.

M & L for Reinforceed cement concrete type-A1, 1:1.5:3 (20mm graded stone aggregate) Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified.

M & L for reinforcement cement concrete type-A1, 1:1.5:3 (using 20mm graded stone aggtegate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including bending, and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed

All as per items No 30 above , but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed.

Use and waste Formwork to sides of concrete of rough finished on flat surfaces in foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

Use and waste Form work in rough finished surfaces of of rectangular, square or polygonal sides of pillars, posts, struts, piers, columns and stanchions complete all as specified.

Use and waste form work Formwork to sides and soffits in rough finished flat surfaces of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and as directed.

Use and waste Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick in rough finished flat surfaces of concrete complete all as specified and as directed.

M&L for rendering 10 mm thick on concrete surface in cement mortar (1:6) as backing coat and 5 mm th in CM 1:4 using finishing the surface even and smooth without using extra cement, including mixing only liquide water proofing compound as per manufacturer instruction complete all as specified and as directed on External surface. Note:- WPC will be measured & Paid separately

M & L for rendering 05mm thick in CM 1:3 on ceiling surfaces of cement concrete and finished the surface even and smooth without using extra cement complete all as specified & directed .

M&L for 75 mm thick cement concrete 1:4:8, type D-2, using 40 mm graded stone aggregate, as in Sub base for floor complete all as specified and as directed.

M&L for 40 mm thick cement concrete 1:4:8, type D-2, using 40 mm graded stone aggregate, as in floors and fininshing surface even and smooth without using extra cement complete all as specified and as directed.

M&L for chequered cement concrete tile with grey cement and pigment (of approved tint) of size 20 cm x 20 cm x 25mm thick over and including 15 mm thick screed bed in cement Mortar 1:6, set, jointed and pointed in neat cement slurry complete all as specified.

Supply only for water proofing compound.

S & F Powder Coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

S & F Anodised aluminium window and ventilator shutters, powder coated, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.

Supply and Fix Anodised aluminium door shutters, powder coated, aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified and directed.

S&F Sheet glass 4 mm thick, ordinary quality and glazing with oil putty in square exc 0.5 Sqm in each pane including fixed with wooden beads/glazing pins/rubber beadings or spring clips in wooden or metal frames complete all as specified and as directed.

S & F for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S & F for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed.

S& F Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. inclug cleats, (Fe-410) brackets, etc.complete all as specified and as directed.

M&L for preparation of new surfaces of steel n. exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L for preparation of new plastered surface and applying two coat of white or tinned with cement base paint over priming coat on exterior wall complete all as specified and directed by Engr-in-Charge.

M&L for applying three coats of white wash on new ceiling surface including preparation of surfaces complete all as specified.

AGE EM SCHEDULE PART - II M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade FRLSH IS 694 cable with multi stranded copper conductor of size 1.5 sqmm (Nominal area) drawn through casing caping with all fittings including plastic laminated sheet cover for mounting switch sockets and drawing continuous earth wire with PVC insulated unsheathed 1100 volts grade cable with multi stranded copper conductor of size 1.5 sqmm (Nominal area) connected to earth dolly complete all as specified and as directed by Engr-in-Charge.

All as per Item No. 53 above but for one 2/3 pin socket outlet, 5 Amps on independent board, complete all as specified and directed. Make- Cable- Finolex/RR cable/Havells, PVC Casing Capping- Presto plast/Finolex/Kalinga.

All as per Item No. 53 above but with FRLSH, ISI marked PVC insulated and unsheathed two single core multistranded copper cable of size 4.0 sqmm for one power point ,3 pin 15 Amps on independent board including FRLSH, ISI marked PVC insulated unsheathed single core multi-stranded copper cable of size 4.00 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

S&F of switch piano flush type 5 amps single pole one way complete one light/fan point controlled by one switch all as specified and directed by Engr-in-Charge

Supply and fix switch socket combination (ISI marked) 2/3 pin and 5 Amps, flush type, 240 volts complete all as specified and as directed. Make- Havells/anchor/ Legrand.

S&F Switch socket combination 2 in 1 5A/16A, 3 pin 1 flush type universal complete all as specified and directed.

S & F ceiling rose surface type 65 mm x 50 mm, 2 to 3 terminal complete all as specified and as directed by Engr-in-Charge

Supply and fixing LED batten fittings 1x18/20 Watt complete pre wired fixed to wall with 2 nos PVC block of suitable size complete all as specified and as directed. make Crompton cat no LCTL 18 CDL or equivalent inPhilips/Jaquar/Havells

Supply and fixing LED security light 35 watt 230 V AC outdoor type with high pressure die cat aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP66 protection complete all as specified and directed

Supply and fix in repairs MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link, 4 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed. Make: Schnieder/L&T/C&S.

Supply and fix MCB, SPN, 240 Volt, 32 Amps, 10 kA rupturing capacity 'C' series, AC complete all as specified and directed by Engr-in Charge. Make:L&T/ Schnieder/Legrand .

Supply and fix MCB SP, 240 Volt, 6-32 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed. Make:L&T/ Schnieder/Legrand .

Supply and laying or fixing or passing through pipe, 16 sqmm 2 core 1100 volts grade heavy duty cable with PVC insulated multistranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed in service connections complete all as specified and as directed.

M/S MANOJ KUMAR BAL

M/S C.M.V CONSTRUCTIONS

Ms Amrik Singh Bahra