REPAIR / REPLACEMENT / MAINT OF SECURITY LIGHTS AND CONNECTED WORKS IN MD ACCN OF OFFRS /JCOS / ORS ALONGWITH JUNCTION BOXES, TIMER SWITCHES, EARTHING OF ARTY CENTRE UNDER GE NASIK ROAD.

Amount

Dismantling and taking down by disconnecting electric connection from existing serviceable /unserviceable /partly unserviceable street/security/flood light fittings or any other light fitting of any type/any wall, fitting and fixture etc and serviceable light fitting will be reuse in other loction and making good to the disturbed surfaces etc complete all as specified and directed at site. (contractor may details one electrician daily basis to attend day to day job card complaints)

Fixing only in repair and connecting after testing only serviceable street / security / flood light fittings of any type / any watt, fitting and fixtures etc. other location including wiring from junction box to the fitting. (street / security / flood light fittings will be reused obtained / removed against item no 01 herein above), complete all as specified and directed at site.

S&F in repairs LED 60W street light fitting, pressure die cast aluminum housing, heat resistance toughened glass, IP 66 protection, better optics for uniform distribution, aesthetically designed roadway luminiare with excellent thermal management,surge protection device 5KV upto rated power 150 W , complete all as specified and directed.

S&F in repairs 80 W LED Flood light fitting, pressure die cast with IP 66 protection, efficient high output emmitter LED for better distribusion, surge protection device 5KV upto rated power 150 W , complete all as specified and directed.

S&F in repairs LED outdoor drivers, suitable for 36-45W street light fitting all as specified and directed.

S&F in repairs LED outdoor drivers, suitable for 60W street light fitting all as specified and directed.

S&F in repairs power contactors ML-3 , 3 pole rating not less than 40A , 230 coil. All as specified and directed.

S&F in repairs AlphaRex3 digital time switches D-22 astro , multifunctional digital time switches all as specified and directed by Engineer-in-Charge.

Supply , install, Design testing and commissioning of CPRI approved factory made and tested outdoor type floor mounted LT panel board, cubical type suitable for 415 volts, 3 phase, 4 wire, 50 HZ AC supply system having bus bar chamber with air insulated PVC sleeved aluminium bus bar of rating 300 Amps for phases and neutral installed on porcelain insulators. The panel shall be dust and vermin proof IP-54 class protection and made out of 3.00 mm CRCA MS sheet with projected globe roof for rain water protection Dust & Vermin proof, including Neoprene rubber gasket, Bottom detachable Gland Plate comp-lete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and 50 X 50 X 6 mm thick MS angle iron frame 60 cm above and 60 cm below normal ground level work front & back opening double door type of adequate size for housing LT switchgear and measuring instruments duly powder coated after seven tank process on both sides including internal wiring in the panel with PVC insulated multi stranded copper conductor cable 1100 Volt grade IS 694 marked or PVC sleeved copper strips of appropriate size but not less than 4.0 sq mm, cable lugs cable gland and PCC foundation in cement concrete 1:3:6 (20 mm graded stone aggregate, testing after installation including complete all as specified & directed and comprising of followings:- (A) Incoming:- (a) Aluminium bus bar TPN 450 Amps - 01 Set (i) Danger notice plate/ sticker of suitable size on front panel board -01 No (ii) MCCB 4 pole 200 A 25 kA- 01 No (B) Outgoing:- (i) MCCB TP 100 Amps 04No (ii) MCCB TP 63 Amps 02 No (iii) MCCB SPN 63 Amps 01 Nos (iv) Each outgoing Feeder Name Radium Sticker Inside Panel. (v) voltmeter, Ammeter and selecor switch (vi) Phase indication lamp R, Y, B LED type

Dismantling of existing U/S HT/ LT pole of any size & type from its position carefully and removing from the site and necessary excavation and earth work in any soil/strata, demoltion of concrete, disconnection of conductor fom pole etc. complete all as directed.

Supply, install erect in trench vertical position steel tubular seweaged welded poles complete with MS base plate of 6mm thick of size 450mm x 450mm finial taper plug pole cap, bolts, nut and screwed, pole made out of ERW MS tubing confirming to IS 2713 Part II of 9 mtr long 410 SP-31 including drilling of holes of required size and nos for fixing of cross arms bracing support/ taking out of cables etc and painting with one coat of red oxide primer and two coat of aluminium paint for exposed surface and two coat of black bituminious paint for the portion embeded in concerete complete all as specified and as directed by Engineer -in-charge.

S&F in repair Decorative gate light made up of high grade unbreakable polycarbonate material suitable for retrofit CFL 8W/14W (TU) B22 base Moon (Opal) including joining pipe , CFL and connecting accessories all as specified and directed by Engineer-in-Charge.

S&F in repairs LIARA IP 65 rated inverted Pyramid Tripod type LED Bollard with soft 360 deg light distribution all as specified and directed by Engr-in-Charge.

S&F LED aviation lighting with cast aluminium housing and polycarbonate all as specified and directed by Engr-in-Charge.

M&L for scrapping the existing deterioted old alumininum paint by iron brushing and painting of steel tubular poles of (9.0 mtr length/11 mtr length ) with one coat of metal primer and two coat of aluminium paint over exposed portion of pole above PCC coping including cross arms, angles, nut, bolts, clamps and S&F new radium sticker Radium paint / sticker of different colour 80 cm above coping of pole, i.e. alernatively with sky blue / red & white radium sticker (10 cm - 04 sky blue / red strip and 10 cm - 04 white strip) complete circumference of any type any shape pole and cement base paint on coping portion, marking of pole nos with radium yello / black paint /steekar in round shape 15 cm dia with letter writing 5 cm height 5 mm width etc. complete all as specified and directed at site.complete all as specified and directed at site by Engineer-in-Charge

S&F junction box of size Size 250 x 200 x 100mm complete with industrial connector including clamps made out of MS flat iron 30 x 5mm and suitable size of MCB and connection from junction box to street light all as specified and directed.

Taking down of street light bracket including clamps of any type/any size from pole/wall including necessary nuts & bolts as directed complete all as specified and directed.

M&L for fabrication and installation of GI pipe bracket made of medium frade tubing of size 40mm dia duly bended by hot forging after filling of sand, length 1.20 mtr including two pairs of MS flat strip clamps 30 x 5mm with GI bolts, nuts and washers complete all as specified and directed.

S&F in repaires PVC insulated 2 core 1.5 sqmm multistranded (un armoured 2XY) copper conductor complete all as specified and directed.

Taking down old unserviceable metal box and S&Fing MS enclosure made out of CRCA sheet 3.00mm thick of size 450mm x 450mm x 250mm depth with three phase aluminium bus bar mounted on epoxy insulators, fixing arrangement with suitable MS Clamps all as specified and directed.

Taking down unservisable U/G cable,service wire from trenches, wall, floor etc upto 50 sqmm

Taking down unservisable U/G cable,service wire from trenches, wall, floor etc above 50 sqmm to 95 sqmm

S&F XLPE insulated armoured and pvc sheated heavy duty electric cable size of 2 core 10 sqmm aluminium conductor 1100 volt grade as per IS 7098 (Part-1) 1988 with latest amendment laid in tranches passing through pipes /ducts including testing complete note- rate is inclusive of cable gland & cable lugs

All as per Item No. 23.00 but size of 4 core 16 sqmm

All as per Item No. 23.00 but size of 3.5 core 35 sqmm

All as per Item No. 23.00 but size of 3.5 core 50 sqmm

All as per Item No. 23.00 but size of 3.5 core 70 sqmm

All as per Item No. 23.00 but size of 3.5 core 95 sqmm

Excavation in trenches in soft / loose soil not exceeding 1.5 mtr deep and not exceeding 1.5 mtr wide for laying of cable, RCC poles / stays and struts etc. and getting out including trimming sides and forming bottom surface complete all as specified and directed at site.

Returning, filling in including spreading, leveling, watering and well ramming excavated soil in layers not exceeding 25 cm thick each, back in trenches after cables have been laid and tested, poles, stays , struts have been erected and tested , all as specified and directed.

Removing excavated surplus soil (Soft/hard soil) obtained from excavation to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified and directed.

Plain cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate for coaping of pole

Plain cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete as specified.

Material and labour for Double Walled Corrugated DWC HDPE Pipe of outer dia 50mm and innter dia 38mm including 90 degree bends with coupler and rubber ring laid in trenches of size 50 mm suitable for cable protection of size 2 core 10 sqmm to 3.5 core 50 sqmm complete all as specified and directed.

Material and labour for Double Walled Corrugated DWC HDPE Pipe of outer dia 90mm and innter dia 78mm including 90 degree bends with coupler and rubber ring laid in trenches of size 90 mm suitable for cable protection of size 3.5 core 70 sqmm to 3.5 core 150 sqmm complete all as specified and directed.

Dismantling of U/S existing cross arms by means made from channels, angles, U/S CI clamps, nuts, bolts etc. from OH line and removing complete.

S & F Cross arms ,bracings,supports,clamps and back plate fabricated from structural steel sections including nuts ,bolts, in any shape or size as indicated or directed and inclusive of two coat of aluminium paint over a coat of red oxide .

S & F Switch air break gang operated triple pole mechanically operated mounted on insulator and steel frame out door type suitable for vertical installation single brake provided with locking arrangement, consisting of MS channel ,HT post type insulator ,copper alloy high pressure assembly ,operating rod of GI pipe medium grade confirming to IS-1818 of 1972 ,suitable for 11000 volt ,200 Amps incl dismantling of old one all as specified.

M&L Earthing with 600X600X6 mm thick , galvanised steel earth plate electrode buried vertically in ground (Earth pit not less than 2.25 meter deep below normal ground level ) with top edge of plate vertically at a depth ,not less than 1.5 m below ground level connected to and including GI strip of size 32X6 mm by means of bolts,nuts,check nuts, And washer of galvanised steel, Gi shrip to be provide upto the extent of 7.5 m GI strip to be duly connected to metalic bodies of HT/LT equipment with provision of mixture of charcoal dust & common salt packed all ground the earth plate upto MS funnel with wire mesh provided inside concrete earth pit for watering arrangement,complete all as shown on electrical plate no.3 of SSR Part I (2009) and testing on completion.

Material and labour for earthing complete with galvanized steel earth plate electrode size 600x600x6.3mm thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below ground levels with top edge of the earth plate not less than 1.5 mtr below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanized earth lead 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized including GI protection pipe light grade 15mm dia connected to main earth wire on pole or control board and GI pipe light grade 20mm dia bore for watering funnel with wire mesh. CI cover with frame, PCC chamber pit with PCC 1:3:6 type C-2 excavation and earth work all as shown in electrical plate No 5 connected to earthing test point all as specified or indicated including testing on completion Note : The unit rate includes for protection pipe and GI earth wire 4.00mm dia from top of earth plate up to 7.5 meter above ground level.

S&F in repairs cable jointing kit of size 4 core 16 sqmm to 50 sqmm all as specified and directed.

S&F in repairs cable jointing kit of size 3.5 core 50 sqmm to 95 sqmm all as specified and directed.

M&L for cable jointing kit for 11 KV ( Earthed) grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 3 core 95 sqmm all as specified and directed by Engr-in-Charge

M&L for cable jointing kit for 11 KV ( Earthed) grade cable for indoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 3 core 95 sqmm all as specified and directed by Engr-in-Charge

M&L for cable jointing kit for 11 KV ( Earthed) grade cable for outdoor termination Heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 3 core 95 sqmm all as specified and directed by Engr-in-Charge

EXCAVATION BY TENCHLESS TECH - Boring of holes under road, pavement, hard standing by trenchless technology using ultra sound technique and necessary machine including HDPE pipe of 150 mm dia. Suitable for 0.4 mpa working pressure.

Taking down of faulty LT underground cable of size upto 3.5 x 35 sqmm from trenches/pole/wall etc for detecting fault including repair and jointing at site including relaying at the same location complete : Note : Excavation/Earth work and cable jointing & jointing kit shall be measured and paid for separately under relevant item of schedule .

S & F MCCB TP in LT Panel thermal magnetic setting of current amp 125A , breaking capacity 16 KA complete with lugs ,spreader link, gland to cable complete all as specified and directed by Engr-In-Charge.

S & F MCCB TP in LT Panel thermal magnetic setting of current amp 100A , breaking capacity 16KA complete with lugs ,spreader link, gland to cable complete all as specified and directed directed by Engr-In-Charge.

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 21,970.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

DURGAI ELECTRICALS

LOKMANYA ENTERPRISES

SHRI SULAI ELECTRICALS

Bidder Name

SHRI SULAI ELECTRICALS

LOKMANYA ENTERPRISES

metro electrical services

DURGAI ELECTRICALS