COMPOSITE WORKS

PIPING-OFFSITES

PIPING (ABOVE GROUND) :-Transportation of all piping items from Owners storage point to work site/work shop; fabrication including cutting, edge preparation, (inclusive of grinding the edges of pipe, pipe spools, fittings, flanges etc. to match with the mating edges of uneven/different thickness wherever required); fitup, bending, preheating wherever required, welding, threading, and laying of pipes and pipe spools (spools along with supports) of all types and thickness over sleepers, overhead on racks and at all elevations, hook-ups with existing piping, connecting with equipment nozzles, strainers, steam traps, static mixers, sight flow indicators, thermal sleeve, orifice assemblies, spray nozzles, rotameters, tappings for pressure gauges, thermowells, sample connections, sample coolers, closed sample system cabinets etc. and fixing of gaskets, bolts, nuts including application of torque wherever required and all other inline instruments and fittings, like elbows, reducers, tees, flanges, spectacle blinds and spacer and blinds, piping specials such as mitres and fabricated fittings, vents, drains (but excluding reinforcing pads), SW valves upto 1.5 NB, Steam Supply/ Condensate Recovery stations(Cast/Fabricated), Supply and welding of Strip as per EIL Std 7-51-0112 to all pipes before hydro-testing at exit points of Units for earthing purpose; alignment, cleaning and flushing by water/compressed air, hydrostatic, pneumatic, vacuum, spark testing and any other type of testing as specified draining, drying by compressed air, performing Positive Material Identification(PMI) using alloy analysers, completing all such works in all respects (including preparation of isometrics as mentioned in the Scope of Work for the job) as per the specifications, drawings and instructions of Engineer-in-Charge. PMI shall be performed by third party as defined in PMI spec.Rates for tubing (if any) shall include rates for valves, fittings, all in line instruments and testing etc. Carbon steel piping includes LTCS piping also. Erection of all inline instruments like flow instruments and specialty items like static mixers, sample coolers, thermal sleeve, air mixers, exhaust head, rupture disk, flow meters, venturi tube, flame arrestor, thermal flow switch etc. except valve shall be considered as part of piping and separate payment shall not be made on this account. Note : Contractor to refer to Instrumentation SOR for specific details and rates of Instrumentation items not covered herein.

CARBON STEEL PIPING (NON IBR); THK. <= 10MM

FABRICATION (BUTT WELD- MANUAL)

NB UPTO 1.5 INCH

NB 2 INCH - 6 INCH

NB 8 INCH - 14 INCH

NB 16 INCH - 24 INCH

NB 26 INCH - 36 INCH

FABRICATION (FILLET WELD)

NB UPTO 1.5 INCH

ERECTION (OTHER THAN SPOOL)

NB UPTO 1.5 INCH

NB 2 INCH - 6 INCH

NB 8 INCH - 14 INCH

NB 16 INCH - 24 INCH

NB 26 INCH - 36 INCH

CARBON STEEL PIPING (NON IBR); THK. > 10MM AND <= 20MM

FABRICATION (BUTT WELD- MANUAL)

NB 16 INCH - 24 INCH

NB 38 INCH - 48 INCH

ERECTION (OTHER THAN SPOOL)

NB 16 INCH - 24 INCH

NB 38 INCH - 48 INCH

STAINLESS STEEL PIPING (NON-IBR); THK. <= 10MM

FABRICATION (BUTT WELD- MANUAL)

NB 2 INCH - 6 INCH

FABRICATION (FILLET WELD)

NB UPTO 1.5 INCH

ERECTION (OTHER THAN SPOOL)

NB 2 INCH - 6 INCH

VALVES :- Transportation of all types of valves (Including special valves and motor operated valves) from Owners storage points to contractors stores/worksite and installation of valves for all rating including assembly of valves accessories like air bottles etc, if any, fixing of gaskets bolts/nuts wherever required and performing Positive Material Identification(PMI) using alloy analysers as per specification, drawings and directions of Engineer-in-Charge. Note : For PRDS, PSVs, TSVs, Control valves, On-Off/Shutdown valves and Self actuating valves all details and rates shall be as per Instrumentation SOR.

FLANGED/WAFER VALVES INCLUDING MOV (UPTO 600#)

NB 2.000 INCHES

NB 8.000 INCHES

SPRING SUPPORT ASSEMBLIES :- Transportation of all types of spring support assemblies from Owner's storage points to contractor's stores/worksite and installation of spring support assemblies for all rating including assembly, if any, fixing of gaskets bolts/nuts, welding attachments wherever required and performing Positive Material Identification(PMI) using alloy analysers as per specification, drawings and directions of Engineer-in-Charge. Contractor to ensure that travel stops are removed and spring is locked in cold load position for Hydrotest. It shall be ensured that locking devices are removed and springs are properly set at hot load position during commissioning.

BOLT TENSIONING :- Carrying out tensioning of bolted joints on all types of piping as called for in EIL Specification No.6-76-0002 on already erected system including supply of all materials, recording devices, instruments etc; Providing all normal and special equipment and gadgets, skilled / un skilled labour, specialist, supervisory staff and completing the work in all respects as per specifications and instructions of engineer-in-charge. some joints may require bolt tensioning more than once, but, payment for one joint shall be made only once.

150# JOINTS

NB 24.000 INCHES

300# JOINTS

REINFORCING PADS FOR PIPES :- Fabrication of reinforcing pads for pipe connection wherever required (from pipes only supplied by the Owner) and erection, fitup, welding and testing (including DP/MP) if required of the same and performing Positive Material Identification(PMI) using alloy analysers as per the specifications, drawings and instructions of the Engineer-in-Charge. Note: Sizes mentioned for Reinforcing Pads are for branch pipe

C.S REINFORCING PADS

NB 8.000 INCHES

RADIOGRAPHY :- Performance of radiographic inspection on piping of all types and thicknesses including providing or hiring of all necessary equipment and whatever else even though not expressly mentioned but required to perform the work as per specifications and instructions of Engineer-in-Charge. Radiographs shall be submitted to the Engineer-in-charge. (Repeat Radiography due to defective radiograph on repaired joints due to Contractors fault and for additional radiography necessitated due to poor performance of contractors welders shall be done at contractors cost) Note: Unit for radiography quantity is Nos of circumferencial weld joints.

FOR JOINTS THK. <= 8MM (FOR CS OTHER THAN CLASS lV OF JOB NDE SPECIFICATION)

NB 2.000 INCHES

NB 6.000 INCHES

FOR JOINTS THK. <= 8MM (FOR CS AS PER CLASS lV OF JOB NDE SPECIFICATION/AS/SS)

SOR Sl. No.: 82 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M22202000900

NB 8.000 INCHES

NB 24.000 INCHES

SOR Sl. No.: 88 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M22203003300

SOR Sl. No.: 89 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M22300000000

SOR Sl. No.: 91 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M22302000000

SOR Sl. No.: 93 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M22404000000

SOR Sl. No.: 94 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M22405000000

SOR Sl. No.: 96 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M22501000000

SOR Sl. No.: 98 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M22504000000

SOR Sl. No.: 99 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M22505000000

SOR Sl. No.: 100 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M22800000000

SOR Sl. No.: 101 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M22801000000

SOR Sl. No.: 102 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M22802000000

SOR Sl. No.: 103 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M22803000000

SOR Sl. No.: 104 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M23000000000

SOR Sl. No.: 105 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M23003000000

NB 0.750 INCHES

NB 1.000 INCHES

NB 1.500 INCHES

NB 2.000 INCHES

NB 3.000 INCHES

NB 4.000 INCHES

NB 6.000 INCHES

NB 8.000 INCHES

NB 10.000 INCHES

NB 12.000 INCHES

SOR Sl. No.: 116 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M23003001800

NB 16.000 INCHES

NB 18.000 INCHES

NB 20.000 INCHES

NB 24.000 INCHES

NB 42.000 INCHES

SOR Sl. No.: 122 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M23003003300

f all thicknesses supplied by owner as free issue; cutting, edge preparation, rolling, fit up, welding, cleaning, testing (hydrotesting, MP/DP, radiography), wherever required bolts nuts & gaskets including supply of necessary equipment, consumables, labour etc as per standards / specifications and directions of Engineer-in-charge

NB 0.750 INCHES

NB 1.000 INCHES

NB 1.500 INCHES

NB 2.000 INCHES

NB 3.000 INCHES

NB 4.000 INCHES

NB 6.000 INCHES

NB 8.000 INCHES

NB 12.000 INCHES

NB 24.000 INCHES

NB 42.000 INCHES

SOR Sl. No.: 134 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M23201002400

NB 2.000 INCHES

NB 3.000 INCHES

SOR Sl. No.: 137 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M23202000900

NB 24.000 INCHES

NB 42.000 INCHES

SOR Sl. No.: 140 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M23203002400

SUPPLY OF STUDS ALONG WITH NUTS: Supply as per Technical Notes for Fasteners (6-44-0057) from Vendor enlisted in Project Master Supplier List of Studs along with two nuts for diameter < 1" and 3 nuts for diamemter >= 1"of nuts, as per the direction of Engineer in-charge. All Alloy steel fasteners used in SS Piping shall be Hot Dip Galvanized.

AS FASTENERS (ASTM A193 GR.B7/B7M/A194 GR.2H/2HM)

MODIFICATION/EXTRA WORKS (IF ANY) :- Cutting, bevelling, fitup, welding of different sizes of CS/AS/SS/Higher Alloy piping of all types and thicknessess in shop, in position, on ground/overhead on rack and at all elevations; transportation of pipes, fittings, flanges etc from owners storage point to work site/ work shop, making necessary scaffoldings, consumables, machinery, tools, tackles, labour and supervision including attending repairs for completing the work as per the instruction of Engineer-in-charge.

FLAME CUTTING C.S PIPING IBR/NON IBR

HACKSAW CUTTING C.S PIPING IBR/NON IBR

BEVELLING C.S PIPING IBR/NON IBR

FITUP & WELDING C.S PIPING IBR/NON IBR

FLAME CUTTING S.S PIPING IBR/NON IBR

HACKSAW CUTTING S.S PIPING IBR/NON IBR

BEVELLING S.S PIPING IBR/NON IBR

FITUP & WELDING S.S PIPING IBR/NON IBR

REMOVAL ERECTED PIPING(ABOVE GROUND) :- Removal of piping existing/ erected including SW valves for modification as required as per Drawings/P and IDs/instructions of Engineer-in-charge at all elevations, including providing assistance to owner for draining, cleaning and purging of the lines to be removed , unbolting of flanged joints /cutting of pipe lines wherever required, installation of flanges and blind flanges, removal of insulation from insulated lines, removing supports, steam tracers, all fittings and flanges, instruments etc, cutting of pipes in appropriate length for transporting purposes, cleaning, flushing, drying and transporting all materials to storage point(within the complex battery limits) designated by Owner/EIL including stacking of material and disposing of waste etc as instructed by Engineer-in-charge.

C.S/A.S PIPING

S.S PIPING

REMOVAL OF ERECTED VALVES (ABOVE GROUND) :- Removal of all types and ratings of valves by unbolting, cutting etc. as required, cleaning by flushing with water/air etc. as required and transportation of the same to Owner's storage point (within thecomplex battery limits) and stacking as per instructions of Engineer-in-Charge.

SOR Sl. No.: 105 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M23003000000

NB 0.750 INCHES

NB 1.000 INCHES

NB 1.500 INCHES

NB 2.000 INCHES

NB 3.000 INCHES

NB 4.000 INCHES

NB 6.000 INCHES

NB 8.000 INCHES

NB 10.000 INCHES

NB 12.000 INCHES

NB 24.000 INCHES

NB 42.000 INCHES

SOR Sl. No.: 169 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M23901002400

LOW FRICTION PADS: Supply, fabrication and fixing of low friction pads with suitable bonding materials / fasteners, as specified in Drawings / Isometrics / Special support sketches.

TEFLON PAD WITH COMPRESSIVE STRENGTH (0.25 OFFSET) :1870 PSI

0-16-43-PK-SOR-3001-0-0M || ITEM NO: M24101000000

SOR Sl. No.: 173 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M24102000000

SOR Sl. No.: 174 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M24200000000

SOR Sl. No.: 175 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M24201000000

SOR Sl. No.: 176 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M24202000000

SOR Sl. No.: 177 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M24203000000

PIPE DAVITS : Supply, fabrication & erection of pipe davits as per EIL std. 7-12-023 for lowering of aircooler motors/safety valves from structural platforms, fixing the same to platforms, inspection as per specs., supply of all necessary materials, equipment, consumables, labour, supervision etc. The work shall be carried out as per the specifications, drawings & instruction of engineerincharge.

SOR Sl. No.: 179 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M25201000000

SOR Sl. No.: 180 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910000000

SOR Sl. No.: 181 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910010000

SOR Sl. No.: 182 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910010100

SOR Sl. No.: 183 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910010200

SOR Sl. No.: 184 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910010300

SOR Sl. No.: 185 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910010400

SOR Sl. No.: 186 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910010500

SOR Sl. No.: 187 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910010600

SOR Sl. No.: 188 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910010700

SOR Sl. No.: 189 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910030000

SOR Sl. No.: 190 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910030100

SOR Sl. No.: 191 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910030200

SOR Sl. No.: 192 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910030300

SOR Sl. No.: 193 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910030400

SOR Sl. No.: 194 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910030500

SOR Sl. No.: 195 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910030600

SOR Sl. No.: 196 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910030700

SOR Sl. No.: 197 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910030800

SOR Sl. No.: 198 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910030900

SOR Sl. No.: 199 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910031000

SOR Sl. No.: 200 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910031100

SOR Sl. No.: 201 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910050000

SOR Sl. No.: 202 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910050100

SOR Sl. No.: 203 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910050200

SOR Sl. No.: 204 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910050300

SOR Sl. No.: 205 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910050400

SOR Sl. No.: 206 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910050500

SOR Sl. No.: 207 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910050600

SOR Sl. No.: 208 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910050700

SOR Sl. No.: 209 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910050800

SOR Sl. No.: 210 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910050900

SOR Sl. No.: 211 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910051000

SOR Sl. No.: 212 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910051100

SOR Sl. No.: 213 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910051200

SOR Sl. No.: 214 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29910051300

SOR Sl. No.: 215 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M299100

CPLNG.LH, B-16.11, ASTM A 105, SW, 3000, 1.5 INCH

VALVES

VLV.GATE, SHEET 51001, 0.5 INCH

VLV.GATE, SHEET 51001, 0.75 INCH

VLV.GATE, SHEET 51001, 1.0 INCH, LOCK OPEN

VLV.GATE, SHEET 51001, 1.0 INCH

VLV.GATE, SHEET 51001, 1.5 INCH, LOCK OPEN

VLV.GATE, SHEET 51001, 1.5 INCH

VLV.GATE, SHEET 51007, 0.75 INCH

VLV.GATE, SHEET 51045, 0.5 INCH

VLV.GATE, SHEET 51045, 0.75 INCH

VLV.GLOBE, SHEET 52001, 1.0 INCH

VLV.GLOBE, SHEET 52007, 1.0 INCH

VLV.CHECK, SHEET 53001, 1.0 INCH

VLV.CHECK, SHEET 53007, 1.0 INCH

VLV.CHECK, SHEET 53050, 0.75 INCH

GASKETS

GASKET, B-16.20-ANSI B16.5, SP.WND SS316+GRAFIL+ I RING, SPIRAL, 150, 0.75 INCH

GASKET, B-16.20-ANSI B16.5, SP.WND SS316+GRAFIL+ I RING, SPIRAL, 150, 1.0 INCH

GASKET, B-16.20-ANSI B16.5, SP.WND SS316+GRAFIL+ I RING, SPIRAL, 150, 1.5 INCH

GASKET, B-16.20-ANSI B16.5, SP.WND SS316+GRAFIL+ I RING, SPIRAL, 300, 1.0 INCH

GASKET, B-16.20-ANSI B16.5, SP.WND SS316+GRAFIL+ I RING, SPIRAL, 300, 1.5 INCH

FASTENERS

BOLT.STUD WITH 2 NUTS, B-18.2, A193 GR.B7, A194 GR.2H, 0.5 INCH X 2.5 INCH

BOLT.STUD WITH 2 NUTS, B-18.2, A193 GR.B7, A194 GR.2H, 0.5 INCH X 2.75 INCH

BOLT.STUD WITH 2 NUTS, B-18.2, A193 GR.B7, A194 GR.2H, 0.625 INCH X 3.0 INCH

BOLT.STUD WITH 2 NUTS, B-18.2, A193 GR.B7, A194 GR.2H, 0.625 INCH X 3.25 INCH

BOLT.STUD WITH 2 NUTS, B-18.2, A193 GR.B7, A194 GR.2H, 0.625 INCH X 3.5 INCH

BOLT.STUD WITH 2 NUTS, B-18.2, A193 GR.B7, A194 GR.2H, 0.625 INCH X 3.75 INCH

BOLT.STUD WITH 2 NUTS, B-18.2, A193 GR.B7, A194 GR.2H, 0.625 INCH X 4.0 INCH

BOLT.STUD WITH 2 NUTS, B-18.2, A193 GR.B7, A194 GR.2H, 0.75 INCH X 3.5 INCH

BOLT.STUD WITH 2 NUTS, B-18.2, A193 GR.B7, A194 GR.2H, 0.75 INCH X 4.0 INCH

BOLT.STUD WITH 2 NUTS, B-18.2, A193 GR.B7, A194 GR.2H, 0.75 INCH X 4.25 INCH

BOLT.STUD WITH 2 NUTS, B-18.2, A193 GR.B7(HDG), A194 GR.2H(HDG), 0.5 INCH X 2.5 INCH

FOR JOINTS THK. <= 8MM (FOR CS OTHER THAN CLASS lV OF JOB NDE SPECIFICATION)

NB 0.750 INCHES

NB 1.000 INCHES

NB 1.500 INCHES

NB 2.000 INCHES

NB 3.000 INCHES

NB 4.000 INCHES

NB 6.000 INCHES

FOR JOINTS THK. <= 8MM (FOR CS AS PER CLASS lV OF JOB NDE SPECIFICATION/AS/SS)

NB 2.000 INCHES

SOR Sl. No.: 82 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M22202000900

NB 8.000 INCHES

NB 12.000 INCHES

NB 18.000 INCHES

NB 24.000 INCHES

SOR Sl. No.: 263 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29920030100

SOR Sl. No.: 265 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29920030300

Supply,fabrication and fixing of low friction pad (SS 304 mirror finish) with suitable bonding material/ fasteners as specified in drawing/documents/special support sketches/isometrics/Gads etc.

SOR Sl. No.: 105 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M23003000000

NB 0.750 INCHES

NB 1.000 INCHES

NB 1.500 INCHES

NB 2.000 INCHES

SOR Sl. No.: 270 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29940010000

SOR Sl. No.: 272 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29940010200

SOR Sl. No.: 274 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M29940010400

SOR Sl. No.: 179 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M25201000000

SURFACE PREP, PRIMER & FINISH COAT FOR CS, AS & LTCS BARE SURFACES FOR ENVIRONMENT AS PER JOB SPEC B861-000-06-42-PLS-01

DESIGN TEMP GROUP: -16 TO 80(DEG C)SURFACE PREPARATION:SSPC-SP-10;1coat of F-9 @ 65-75µ DFT/coat, PRIMER: 1 coat of P-6 @ 40µ DFT/coat, FINISH COAT: 2 coats of F-6B @ 100µ DFT/coat + 1 coat of F-2 @ 40µ DFT/coat (2x100 + 40= 240). Total DFT = 345-355.

SOR Sl. No.: 278 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010000

SOR Sl. No.: 279 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010400

SOR Sl. No.: 280 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010500

SOR Sl. No.: 281 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010600

SOR Sl. No.: 282 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010800

SOR Sl. No.: 283 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010900

SOR Sl. No.: 284 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102011100

SOR Sl. No.: 285 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102011300

SOR Sl. No.: 215 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M299100

SURFACE PREP, PRIMER & FINISH COAT FOR CS, AS & LTCS BARE SURFACES FOR ENVIRONMENT AS PER JOB SPEC B861-000-06-42-PLS-01

DESIGN TEMP GROUP: -16 TO 80(DEG C)SURFACE PREPARATION:SSPC-SP-10;1coat of F-9 @ 65-75µ DFT/coat, PRIMER: 1 coat of P-6 @ 40µ DFT/coat, FINISH COAT: 2 coats of F-6B @ 100µ DFT/coat + 1 coat of F-2 @ 40µ DFT/coat (2x100 + 40= 240). Total DFT = 345-355.

SOR Sl. No.: 278 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010000

SOR Sl. No.: 279 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010400

SOR Sl. No.: 280 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010500

SOR Sl. No.: 281 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010600

SOR Sl. No.: 282 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010800

SOR Sl. No.: 283 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010900

SOR Sl. No.: 284 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102011100

SOR Sl. No.: 285 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102011300

SOR Sl. No.: 295 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102021100

SOR Sl. No.: 297 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102021500

SOR Sl. No.: 179 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M25201000000

SURFACE PREP, PRIMER & FINISH COAT FOR CS, AS & LTCS BARE SURFACES FOR ENVIRONMENT AS PER JOB SPEC B861-000-06-42-PLS-01

DESIGN TEMP GROUP: -16 TO 80(DEG C)SURFACE PREPARATION:SSPC-SP-10;1coat of F-9 @ 65-75µ DFT/coat, PRIMER: 1 coat of P-6 @ 40µ DFT/coat, FINISH COAT: 2 coats of F-6B @ 100µ DFT/coat + 1 coat of F-2 @ 40µ DFT/coat (2x100 + 40= 240). Total DFT = 345-355.

SOR Sl. No.: 278 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010000

SOR Sl. No.: 279 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010400

SOR Sl. No.: 280 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010500

SOR Sl. No.: 281 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010600

SOR Sl. No.: 282 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010800

SOR Sl. No.: 283 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010900

SOR Sl. No.: 284 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102011100

SOR Sl. No.: 285 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102011300

SOR Sl. No.: 308 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49201011100

SOR Sl. No.: 310 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49201011500

SOR Sl. No.: 312 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49201011800

SOR Sl. No.: 313 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49201012100

SOR Sl. No.: 314 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49201012400

SOR Sl. No.: 215 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M299100

SURFACE PREP, PRIMER & FINISH COAT FOR CS, AS & LTCS BARE SURFACES FOR ENVIRONMENT AS PER JOB SPEC B861-000-06-42-PLS-01

DESIGN TEMP GROUP: -16 TO 80(DEG C)SURFACE PREPARATION:SSPC-SP-10;1coat of F-9 @ 65-75µ DFT/coat, PRIMER: 1 coat of P-6 @ 40µ DFT/coat, FINISH COAT: 2 coats of F-6B @ 100µ DFT/coat + 1 coat of F-2 @ 40µ DFT/coat (2x100 + 40= 240). Total DFT = 345-355.

SOR Sl. No.: 278 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010000

SOR Sl. No.: 279 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010400

SOR Sl. No.: 280 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010500

SOR Sl. No.: 281 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010600

SOR Sl. No.: 282 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010800

SOR Sl. No.: 283 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102010900

SOR Sl. No.: 284 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102011100

SOR Sl. No.: 285 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49102011300

SOR Sl. No.: 308 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49201011100

SOR Sl. No.: 310 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49201011500

SOR Sl. No.: 314 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49201012400

SOR Sl. No.: 326 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49201021500

SOR Sl. No.: 328 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49201021800

SOR Sl. No.: 179 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M25201000000

SOR Sl. No.: 331 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49201023300

NB 0.750 INCHES

NB 1.000 INCHES

NB 1.500 INCHES

NB 2.000 INCHES

NB 3.000 INCHES

NB 4.000 INCHES

NB 6.000 INCHES

SOR Sl. No.: 337 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49910010300

SOR Sl. No.: 215 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M299100

SOR Sl. No.: 331 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49201023300

NB 0.750 INCHES

NB 1.000 INCHES

NB 1.500 INCHES

NB 2.000 INCHES

NB 3.000 INCHES

NB 4.000 INCHES

NB 6.000 INCHES

SOR Sl. No.: 337 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49910010300

SOR Sl. No.: 348 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49910020400

SOR Sl. No.: 350 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49910020600

SOR Sl. No.: 352 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M49910020800

*************************************************************** LEGENDS / NOTES FOR INSULATION WORKS *************************************************************** ** Types of Insulation : CC = Cold Conservation Insulation SC = Surface Condensation Insulation H = Heat Conservation Insulation CPP = Cold Personal protection HPP = Hot Personnel Protection Insulation ** Basic Line Surface Materials: CS = Carbon Steel (Including LT Carbon Steel) AS = Alloy Steel SS = Stainless Steel ** Notes : 1. For Insulation specification, refer " Job specification for Insulation of Piping and Equipment", B861-000-06-43-IL-S001 ***************************************************************

SOR Sl. No.: 179 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M25201000000

SOR Sl. No.: 355 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB0000000000

SOR Sl. No.: 356 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1200000000

SOR Sl. No.: 357 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274000000

NB 00.75 INCHES; THICKNESS 25 MM

NB 01.00 INCHES; THICKNESS 25 MM

NB 01.50 INCHES; THICKNESS 50 MM

NB 02.00 INCHES; THICKNESS 50 MM

NB 06.00 INCHES; THICKNESS 50 MM

NB 08.00 INCHES; THICKNESS 50 MM

NB 012.000 INCHES; THICKNESS 60 MM

NB 018.000 INCHES; THICKNESS 60 MM

NB 24.00 INCHES; THICKNESS 60 MM

NB 28.00 INCHES; THICKNESS 60 MM

SOR Sl. No.: 356 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1200000000

SOR Sl. No.: 357 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274000000

00-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274013312

NB 01.00 INCHES; THICKNESS 25 MM

NB 01.50 INCHES; THICKNESS 50 MM

NB 02.00 INCHES; THICKNESS 50 MM

NB 06.00 INCHES; THICKNESS 50 MM

NB 08.00 INCHES; THICKNESS 50 MM

NB 018.000 INCHES; THICKNESS 60 MM

SOR Sl. No.: 374 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274020910

SOR Sl. No.: 355 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB0000000000

SOR Sl. No.: 377 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274021812

SOR Sl. No.: 379 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274022412

SOR Sl. No.: 355 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB0000000000

SOR Sl. No.: 356 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1200000000

SOR Sl. No.: 382 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274030505

NB 00.75 INCHES; THICKNESS 25 MM

NB 01.00 INCHES; THICKNESS 25 MM

SOR Sl. No.: 377 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274021812

NB 02.00 INCHES; THICKNESS 50 MM

NB 06.00 INCHES; THICKNESS 50 MM

NB 08.00 INCHES; THICKNESS 50 MM

NB 018.000 INCHES; THICKNESS 60 MM

SOR Sl. No.: 388 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274040910

SOR Sl. No.: 179 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: M25201000000

SOR Sl. No.: 391 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274041812

SOR Sl. No.: 355 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB0000000000

SOR Sl. No.: 394 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274043312

SOR Sl. No.: 395 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282000000

NB 00.50 INCHES; THICKNESS 25 MM

SOR Sl. No.: 398 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282010505

SOR Sl. No.: 399 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282010605

SOR Sl. No.: 400 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282010805

SOR Sl. No.: 401 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282010905

SOR Sl. No.: 402 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011105

SOR Sl. No.: 403 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011308

SOR Sl. No.: 404 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011505

SOR Sl. No.: 405 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011508

SOR Sl. No.: 406 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011605

SOR Sl. No.: 407 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011608

SOR Sl. No.: 408 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011808

SOR Sl. No.: 409 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282012108

NB 24.00 INCHES; THICKNESS 60 MM

NB 24.00 INCHES; THICKNESS 50 MM

NB 28.00 INCHES; THICKNESS 60 MM

SOR Sl. No.: 356 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1200000000

SOR Sl. No.: 395 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282000000

NB 00.50 INCHES; THICKNESS 25 MM

SOR Sl. No.: 414 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282020000

SOR Sl. No.: 415 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282020405

SOR Sl. No.: 400 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282010805

SOR Sl. No.: 401 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282010905

SOR Sl. No.: 419 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282020905

SOR Sl. No.: 420 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282021105

SOR Sl. No.: 404 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011505

SOR Sl. No.: 422 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282021505

SOR Sl. No.: 406 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011605

SOR Sl. No.: 407 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011608

SOR Sl. No.: 409 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282012108

SOR Sl. No.: 374 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274020910

SOR Sl. No.: 355 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB0000000000

SOR Sl. No.: 394 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274043312

SOR Sl. No.: 395 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282000000

NB 00.50 INCHES; THICKNESS 25 MM

SOR Sl. No.: 403 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011308

SOR Sl. No.: 407 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011608

SOR Sl. No.: 379 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274022412

SOR Sl. No.: 391 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274041812

SOR Sl. No.: 355 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB0000000000

SOR Sl. No.: 394 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1274043312

SOR Sl. No.: 395 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282000000

NB 00.50 INCHES; THICKNESS 25 MM

SOR Sl. No.: 398 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282010505

SOR Sl. No.: 399 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282010605

SOR Sl. No.: 438 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282040000

SOR Sl. No.: 440 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282040505

SOR Sl. No.: 402 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011105

SOR Sl. No.: 403 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011308

SOR Sl. No.: 404 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011505

SOR Sl. No.: 422 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282021505

SOR Sl. No.: 406 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011605

SOR Sl. No.: 407 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282011608

SOR Sl. No.: 409 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282012108

SOR Sl. No.: 447 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282041508

SOR Sl. No.: 449 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282041608

SOR Sl. No.: 451 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282042108

SOR Sl. No.: 453 || PART NO: 0 || SOR NO: B861-000-16-43-PK-SOR-3001-0-0M || ITEM NO: MB1282042410

ELECTRICAL WORKS

Design, detailed engineering, preparation of documents, manufacture, procurement of materials and bought out components, assembly at shop, inspection, testing at manufacturer's works, preparation of graphics for the total microprocessor based analogue addressable type fire detection & alarm system including supply of required software, packing, delivery of the following, including supply of all commissioning spares & special tools and tackles, erection material & documentation as per the enclosed EIL standard specifications, scope of work/job specification, data sheets etc. and other codes and standards attached or referred.

8-loop microprocessor based DGFAP with HMI with battery &charger (refer block diagram)

Microprocessor based Repeater panel with battery and charger (refer block diagram)

Multi - sensor type addressable detectors with junction boxes for safe area

Intrinsically safeHeat Detector-addressable type

Addressable Linear Beam detectors with transmitter, receiver, reflector for safe area.

Zener barrier

Outdoor weather proof addressable Break Glass Unit (BGU)/Manual call point (IP-65)in safe area.

Indoor addressable Break Glass Unit (BGU) in safe area.

Addressable type electronic hooter with minimum 6W output

Wall mounting type one faced exit signs suitable for indoor location

Ceiling mounting type double faced exit signs suitable for indoor location

Weather proof (IP-65) Fault Isolating Modules for loops connecting outdoor break glass units

Fault Isolating Modules for loops connecting indoor break glass units/detectors/hooters etc.

Control modules with integral junction box installed within loop

Input Module with integral junction box installed within loop

Industrial type 5 km diametrical range siren with Siren control & starter panel

Response indicator for rooms and concealed area for Addressable Fire alarm system

Hooter acknowledge Box

Providing training for TWO Nos. OWNER's Engineers for a period of 4 days at manufacturer works for Fire Alarm system

Providing training for FIVE Nos. OWNER's Engineers at site for the complete fire alarm system

Mandatory spares for Fire Alarm system as per Cl.6.1 (Mandatory spares), sr.no.15 of EDB document no. B861-000-16-50-EDB-1001

Supply, inspection at shop, delivery at site of safe area weatherproof/ indoor push button type desktop/ wall mounting type Analogue caller ID telephone handsets (corded landline phones) with numeric key pad and redialling facility complete with all accessories including all labour and materail. as per approved drawings, specifications of this tender and directions of Engineer-in-Charge Existing exchange distribution boxes make is ADC Krone, UK

Supply, inspection at shop, delivery at site of safe area weatherproof/ indoor push button type desktop/ wall mounting type Analogue non caller ID telephone handsets complete with all accessories including all labour and materail. as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. Existing exchange distribution boxes make is ADC Krone, UK

Installation, testing and commissioning of safe area weatherproof/ indoor push button type desktop/ wall mounting type telephone handsets complete with all accessories including all labour and materail. as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Design, detailed engineering, manufacture, preparation of documents, procurement of materials and bought out components, assembly at shop, inspection, testing at manufacturer's works, packing, supply & delivery of plant communication system

SOR Sl. No.: 481 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC5

SOR Sl. No.: 482 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC5.10

SOR Sl. No.: 483 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC5.20

SOR Sl. No.: 484 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC5.30

SOR Sl. No.: 485 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC6

SOR Sl. No.: 486 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7

SOR Sl. No.: 487 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.10

SOR Sl. No.: 488 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.20

SOR Sl. No.: 489 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.30

SOR Sl. No.: 490 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.40

SOR Sl. No.: 491 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.50

SOR Sl. No.: 492 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.60

SOR Sl. No.: 493 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.70

SOR Sl. No.: 494 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.80

SOR Sl. No.: 495 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.90

SOR Sl. No.: 496 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.100

SOR Sl. No.: 497 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.110

SOR Sl. No.: 498 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.120

SOR Sl. No.: 499 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.130

SOR Sl. No.: 500 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.140

SOR Sl. No.: 501 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.150

SOR Sl. No.: 502 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.160

SOR Sl. No.: 503 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.170

SOR Sl. No.: 504 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.180

SOR Sl. No.: 505 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.190

SOR Sl. No.: 506 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.200

SOR Sl. No.: 507 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.210

SOR Sl. No.: 508 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.220

SOR Sl. No.: 509 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.230

SOR Sl. No.: 510 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.240

SOR Sl. No.: 511 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC7.250

SOR Sl. No.: 512 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC8

SOR Sl. No.: 513 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC8.10

SOR Sl. No.: 514 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC8.20

SOR Sl. No.: 515 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.MC8.30

SOR Sl. No.: 516 || PART

Supply, mounting & wiring of 32A, 110V DC SFC (switch fuse+ contactor) fully equipped outgoing feeder

Supply, mounting & wiring of 16A, 110V DC SFC (switch fuse+ contactor) fully equipped outgoing feeder

Supply, mounting & wiring of 100A, 110V DC Switch

Supply, mounting & wiring of 63A, 110V DC Switch

Supply, mounting & wiring of 32A, 110V DC Switch

Supply, mounting & wiring of 16A, 110V DC Switch

Supply, mounting & wiring of 100A, 110V DC fuse Link

Supply, mounting & wiring of 63A, 110V DC fuse Link

Supply, mounting & wiring of 32A, 110V DC fuse Link

Supply, mounting & wiring of 16A, 110V DC fuse Link

Supply, mounting & wiring of 100A, 110V DC contactor

Supply, mounting & wiring of 63A, 110V DC contactor

Supply, mounting & wiring of 32A, 110V DC contactor

Supply, mounting & wiring of 16A, 110V DC contactor

TRANSFORMERS

Installation of transformers of the following ratings excluding the construction of foundation, including transportation from store/yard to site at the place of installation, unpacking, positioning in place, site assembly of loosely furnished accessories, including connection of auxiliary circuits, topping up with oil and testing of oil with contractor's own test equipment, including fixing of nuts and bolts etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

2 Winding ONAN outdoor transformer with off circuit tap changer. 11 kV / .433 kV 2.5 MV·A

2 Winding ONAN outdoor transformer with off circuit tap changer. 11 kV / .433 kV 1.6 MV·A

2 Winding ONAN/ONAF outdoor transformer with OLTC. 11 kV / 6.9 kV 6.3 MV·A

Filtration of transformer oil by stream line filter machine provided by the contractor for improving the insulation strength of oil to the required strength, including all labour and materials, specifications of this tender and directions of Engineer-in-Charge. (Excluding the supply of oil).

Filtration of transformer oil with dissolved gas analysis test.

Filtration of transformer oil without dissolved gas analysis test.

Supply of transformer oil conforming to IS-335 in non-returnable 220 litre drums for topping up various transformers. The oil shall be tested prior to filling up and improved by filtering, if required, including all labour and materials, specifications of this tender and directions of Engineer-in-Charge.

Filtration of transformer oil with dissolved gas analysis test.

Filtration of transformer oil without dissolved gas analysis test.

Supply of dry type transformers with accessories, including nuts and bolts etc., as per EIL standard specification No. 6-51-0042, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Supply, mounting & wiring of 63A, 110V DC contactor

Supply, mounting & wiring of 32A, 110V DC contactor

Supply, mounting & wiring of 16A, 110V DC contactor

SOR Sl. No.: 543 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1010.60.10V25

SOR Sl. No.: 544 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1010.70

SOR Sl. No.: 546 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1010.70.10V25

SOR Sl. No.: 547 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1010.110

SOR Sl. No.: 549 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1010.110.20V18

SOR Sl. No.: 546 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1010.70.10V25

SOR Sl. No.: 547 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1010.110

Installation, testing and commissioning of switch-boards, relay and control panels, annunciation panels, UPS system, battery chargers, distribution boards, cubicles with electrical equipment, VSD panels, misc. electrical panels etc., including transportation from store/yard to site at the place of installation, unpacking, assembly, including mounting and wiring of loose parts supplied by equipment vendor, interconnection of shipping sections and requisite inter-panel wiring between shipping sections, including supply of all wiring materials, installation on foundations or fixing to wall or steel structures, aligning, levelling, grouting, testing and calibration of relays and meters etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Weight of the Unit

SOR Sl. No.: 553 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.10.10

SOR Sl. No.: 554 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.10.20

SOR Sl. No.: 555 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.20

SOR Sl. No.: 547 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1010.110

Installation, testing and commissioning of bus ducts of following ratings between transformer secondary and the switchgear incomer panel, including transportation from store/yard to site at the place of installation, unpacking, making connections and installation of bends, breaking of walls and making good of the same etc., (but excluding structural supports), including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Air Insulated/segregated bus ducts 415 V 4000 A 65 kA for 1 second

Air Insulated/segregated bus ducts 415 V 2500 A 65 kA for 1 second

Installation, testing and commissioning of switch-boards, relay and control panels, annunciation panels, UPS system, battery chargers, distribution boards, cubicles with electrical equipment, VSD panels, misc .electrical panels etc., including transportation from store/yard to site at the place of installation, lifting the panels by deployment of tyre mounted hydraulic trollies, unpacking, assembly, including mounting and wiring of loose parts supplied by equipment vendor, interconnection of shipping sections and requisite inter-panel wiring between shipping sections, including supply of all wiring materials, installation on foundations or fixing to wall or steel structures, aligning, levelling, grouting, testing and calibration of relays and meters etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 555 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.20

SOR Sl. No.: 547 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1010.110

Installation, testing and commissioning of bus ducts of following ratings between transformer secondary and the switchgear incomer panel, including transportation from store/yard to site at the place of installation, unpacking, making connections and installation of bends, breaking of walls and making good of the same etc., (but excluding structural supports), including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Air Insulated/segregated bus ducts 415 V 4000 A 65 kA for 1 second

Air Insulated/segregated bus ducts 415 V 2500 A 65 kA for 1 second

Weight of the Unit from 1001 upto 1500 kg.

Weight of the Unit from 1501 upto 3000 kg.

Installation of switch-boards, relay and control panels, annunciation panels, UPS system, battery chargers, distribution boards, cubicles with electrical equipment, VSD panels, misc .electrical panels etc., including transportation from store/yard to site at the place of installation, lifting the panels by deployment of tyre mounted hydraulic trollies, unpacking, assembly, including mounting and wiring of loose parts supplied by equipment vendor, interconnection of shipping sections and requisite inter-panel wiring between shipping sections, including supply of all wiring materials, installation on foundations or fixing to wall or steel structures, aligning, levelling, grouting, testing and calibration of relays and meters etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 568 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.210.10

SOR Sl. No.: 570 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.210.30

SOR Sl. No.: 572 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.210.50

SOR Sl. No.: 573 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.240

SOR Sl. No.: 574 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.240.MC10

SOR Sl. No.: 575 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.240.MC20

SOR Sl. No.: 576 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.240.MC30

SOR Sl. No.: 577 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.240.MC40

SOR Sl. No.: 578 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.240.MC50

SOR Sl. No.: 579 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.240.MC60

SOR Sl. No.: 580 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1020.240.MC70

SOR Sl. No.: 581 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1040

ncluding all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Weight of the unit above 5 kg. but upto 20 kg.

Weight of the unit above 20 kg. but upto 100 kg.

Weight of the unit up to 5 kg.

Supply of Industrial, weather proof type Push Button stations as per EIL specification No. 6-51-0014, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

With stop (latching type) push button.

With stop (non-latching type) push button.

With start and stop (latching type) push buttons.

With start, stop push buttons and ammeter.

With stop push button (Break Glass Type).

With start and stop (non-latching type) push buttons.

Supply of flameproof and weather proof type Push Button station as per EIL standard specification No. 6-51-0006 as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

DC SYSTEM / BATTERY BANK

Supply of following ratings of Nickel-cadmium batteries, battery charger, distribution board alongwith accessories as per EIL specification No. 6-51-0019, 6-51-0047, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

160A (Min.) , dual redundant battery charger as per data sheet DS-430

110V, 1x500AH(Min.), Ni-Cd battery bank

110V, 350A DC distribution board as per feeder details listed in scope of work/job specification

3P MCCB / DC Circuit Breaker Battery isolator in weatherproof enclosure(IP-55) of adequate rating.

Mandatory spares for 110V Battery & Battery charger as per Cl.6.1 (Mandatory spares), sr.no.11 of EDB document no. B861-000-16-50-EDB-1001

Installation, testing and commissioning of stationary nickel-cadmium battery banks of the following ratings, including transportation from store/yard to site at the place of installation, filling with electrolyte, charging and dischargng of cells, including capacity test etc., aligning, levelling, grouting, assembly of battery racks, fixing of inter-cell connectors etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Nickel-cadmium battery banks (including capacity test) rated for 110 V 500 Ah

Supply of following rating of cell boosters as per EIL specification No. 6-51-0019, including all labour and materials, as per data sheets, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Cell booster rated for 12 V 50 A

PLUGS, SOCKETS AND JUNCTION BOXES

Supply of weatherproof metal clad 415V, TPN, industrial type socket and plug with heavy duty interlocking switch, with adequately sized cable adaptor box for incoming and outgoing cable terminations, including supply of double compression brass nickel plated cable glands, tinned copper lugs, including all labours and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

63 A, 415 V, 5 pin sockets along with associated 5 pin plugs.

240 V, 15 A, 3 pin sockets.

240 V, 15 A, 3 pin sockets along with associated 3 pin plugs.

24 V, 5 A, 3 pin sockets along with associated 3 pin plugs. WITH TRANSFORMER.(240/24V)

Supply, installation, cable termination, connection, testing and commissioning of following types of FLP and WP junction boxes, as per EIL specification No. 6-51-0061, including all labours and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

WP JB (IP-65) with 15 A, 16 terminals suitable for 1 No. incoming and 6 Nos. outgoing cable entries complete with cable glands for incoming and outgoing cables and 3 Nos. blocking plugs

Supply, installation, cable termination, connection, testing and commissioning of following types of FLP and WP junction boxes, as per EIL specification No. 6-51-0061, including all labours and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 616 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1060.40.MC30

SOR Sl. No.: 617 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1060.40.MC40

SOR Sl. No.: 618 || PART NO: 0 || SOR NO: B861-000-16

Supply of following rating of outdoor type neutral grounding resistor, as per EIL standard specification no.6-51-0043, including all labour and materials, as per approved drawings, specifications of this tnder and directions of Engineer-in-Charge.

NGR rated for 3.81 kV 400 A

Installation, testing and commissioning of outdoor type following neutral grounding resistor consisting of cast iron/stainless steel grid resistor with/without neutral CT including connection of one end of resistor with transformer neutral and the other end of the resistor to the earthing grid, including transportation from store/yard to site at the place of installation, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 622 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1070.20.10V4

Installation, testing and commissioning of outdoor type following neutral grounding resistor consisting of cast iron/stainless steel grid resistor with/without neutral CT including connection of one end of resistor with transformer neutral and the other end of the resistor to the earthing grid, including transportation from store/yard to site at the place of installation, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Supply of following HV capacitor banks, series reactor and RVT, as per EIL standard specification NO. 6-51-0020, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

11kV, 3 Phase, indoor type APFC panel -1500kVAR

Mandatory spares for APFC as per Cl.6.1 (Mandatory spares), sr.no.20 of EDB document no. B861-000-16-50-EDB-1001

Installation of following H.V. capacitor banks, series reactor and RVT, including transportation from store/yard to site of installation, unpacking, assembly of elevating structure, interconnection of loose parts supplied by equipment vendor, aligning, levelling etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

HV capacitor banks rated for 1500 kVAR 11 kV

Testing and commissioning of following H.V. capacitor banks, series reactor and RVT, including testing equipments, all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 630 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1080.40.10V6

SOR Sl. No.: 631 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1090

SOR Sl. No.: 632 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1090.30

SOR Sl. No.: 633 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1090.30.10

SOR Sl. No.: 634 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1090.30.20

SOR Sl. No.: 635 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1090.30.30

Mandatory spares for APFC as per Cl.6.1 (Mandatory spares), sr.no.20 of EDB document no. B861-000-16-50-EDB-1001

Installation of following H.V. capacitor banks, series reactor and RVT, including transportation from store/yard to site of installation, unpacking, assembly of elevating structure, interconnection of loose parts supplied by equipment vendor, aligning, levelling etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

HV capacitor banks rated for 1500 kVAR 11 kV

Frame size upto 80.

Frame size more than 80 and upto 112.

Frame size more than 112 and upto 180.

Frame size more than 180 and upto 250.

Supply, fabrication and installation of GI canopies for outdoor electrical miscellaneous equipments such as lighting/power panels and distribution junction boxes, local panels , PB stations etc. to render them weather proof including supply of necessary hardware for fixing and clamping with the equipment, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 643 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1090.50.10

SOR Sl. No.: 645 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1090.50.30

SOR Sl. No.: 646 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1090.50.40

SOR Sl. No.: 647 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1100

SOR Sl. No.: 648 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1100.10

SOR Sl. No.: 649 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1100.10.10

SOR Sl. No.: 650 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1100.10.20

SOR Sl. No.: 651 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1100.10.30

SOR Sl. No.: 652 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1100.10.40

SOR Sl. No.: 653 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1100.10.50

SOR Sl. No.: 654 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1100.10.60

SOR Sl. No.: 655 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.1130

following, including the supply of necessary clamps, bolts, rawl plugs etc., breaking and making good of walls, if required, mounting, including all labour and materials, complete and as per applicable standards and CEA Guidelines and as per directions of Engineer-in-Charge.

Shock hazard charts complete with frame and glass.

First Aid Boxes.

4.5 kg capacity CO2 type fire extinguishers.

6.8 kg capacity CO2 type fire extinguishers.

9 kg capacity CO2 type fire extinguishers.

Sand buckets with stand (Each with at least 3 sand buckets).

Shock hazard charts - Laminated type

Gas Mask for use in substation during fire & smoke as per CEA guidelines

Supply and laying of 900 mm wide safety insulation mats complying to IS-15652, of following grades required for maintenance of electrical equipment in substation, including cutting to required shape in running length, including all labour and materials, as per applicable Indian or International standards and CEA Guidelines and as per directions of Engineer-in-Charge.

3.3 kV grade.

11 kV grade.

Supply of following items as per applicable Indian standards/CEA Guidelines.

Rubber hand gloves (11 kV grade).

Rubber hand gloves (33 kV grade).

Enamelled caution boards.

Discharge rod with earthing facility (upto 11 kV grade).

HV fuse puller handle.

Supply and application/installation of epoxy based insulation coating with breakdown voltage as per IS, suitable for system voltage as marked and shall be suitable for installation on concrete flooring of substation in airconditioned/non-airconditioned area, having smooth finish, including all labour and materials, complete as per approved drawings, job & standard specification attached with this tender and directions of the engineer-in- charge

For highest systen voltage of 12.1kV

SUPPLY OF SPARES / LAMPS

MV HRC Fuses

SUPPLY OF MV CABLES

Supply of 1100 V grade, Copper Conductor,XLPE insulated and armoured, cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

2 C x 10 sq. mm

2C x 16 sq. mm

2 C x 2.5 sq. mm

3 C x 6 sq. mm

2 C x 4 sq. mm

3 C x 4 sq. mm

3 C x 10 sq. mm

3 C x 2.5 sq. mm

Supply of 1100 V grade, Aluminium Conductor, XLPE insulated and armoured, cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

3 C x 25 sq. mm

3.5 C x 25 sq. mm

3 C x 35 sq. mm

2 C x 50 sq. mm

3 C x 95 sq. mm

3 C x 120 sq. mm

3.5 C x 185 sq. mm

3 C x 240 sq. mm

3 C x 50 sq. mm

3.5 C x 35 sq. mm

3.5 C x 95 sq. mm

3.5 C x 300 sq. mm

3.5 C x 50 sq. mm

NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2010.50.230

SOR Sl. No.: 708 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2010.50.330

SOR Sl. No.: 709 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2010.60

SOR Sl. No.: 710 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2010.60.100

SOR Sl. No.: 711 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2010.60.110

SOR Sl. No.: 712 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2010.60.130

SOR Sl. No.: 713 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2010.60.140

SOR Sl. No.: 714 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2010.60.170

SOR Sl. No.: 715 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2020

SOR Sl. No.: 716 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2020.40

SOR Sl. No.: 715 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2020

Supply of 11 kV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

3 C x 240 sq. mm, Al

3 C x 300 sq. mm, Al

SUPPLY OF HV CABLES (SINGLE CORE)

Supply of 6.6 KV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured single core cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

1 C x 630 sq. mm, Al

Supply of 11 KV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured single core cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 725 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2030.50.20

SOR Sl. No.: 726 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2040

SOR Sl. No.: 727 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2040.10

SOR Sl. No.: 725 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2030.50.20

Supply of 11 KV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured single core cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

1 C x 630 sq. mm, Al

SOR Sl. No.: 726 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2040

SUPPLY OF HV CABLES (SINGLE CORE)

Supply of 6.6 KV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured single core cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

3 C x 300 sq. mm, Al

Cables with OD above 20 mm but upto 30 mm.

Cables with OD upto 20 mm.

Cables with OD above 40 mm but upto 50 mm.

Laying of cables (using cable pulling by motorized winch with torque limits) of different voltage grade and types of the following overall diameters in ready trays/trenches/supported on structure/pull through pipes including supply and fixing of stainless steel strip number tags, supply and fixing of GI saddles & saddle bars, trefoil clamps (for single core cables) etc., including transportation from store/yard to site at the place of installation, unpacking, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge

SOR Sl. No.: 736 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2040.30.10

SOR Sl. No.: 738 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2040.30.30

SOR Sl. No.: 740 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2040.30.50

SOR Sl. No.: 742 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2040.30.70

SOR Sl. No.: 743 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2050

SOR Sl. No.: 744 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2050.120

SOR Sl. No.: 745 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2050.60

SOR Sl. No.: 746 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2050.60.10V3

SOR Sl. No.: 747 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2050.60.30V2

SOR Sl. No.: 748 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2050.60.10V1

SOR Sl. No.: 749 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M

3 Core cable Indoor termination kit for 11 kV 240 mm²

1 Core cable Indoor termination kit for 6.6 kV 630 mm²

1 Core cable Indoor termination kit for 11 kV 630 mm²

Supply of 6.6 KV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured single core cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 726 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2040

1 C x 630 sq. mm, Al

SUPPLY OF HV CABLES (SINGLE CORE)

SOR Sl. No.: 725 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2030.50.20

Supply of 11 KV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured single core cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

3 Core cable termination kit for 11 kV 300 mm²

3 Core cable termination kit for 11 kV 240 mm²

1 Core cable termination kit for 6.6 kV 630 mm²

1 Core cable termination kit for 11 kV 630 mm²

Termination of XLPE insulated armoured power cables (up to 1100 V grade) and connection of leads excluding the supply of cable glands and lugs but including fixing of cable glands, supply and fixing of PVC shrouds for outdoor terminations, cutting and stripping of cable insulation, crimping the lug on to the conductor, clamping of the cable-cores, marking with wire number, ferrules etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 761 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2050.100.60

1 C x 630 sq. mm, Al

SUPPLY OF HV CABLES (SINGLE CORE)

Supply of 6.6 KV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured single core cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 725 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2030.50.20

SOR Sl. No.: 726 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2040

Supply of 11 KV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured single core cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

All sizes from 1P to 4P and upto 2.5 sq. mm

All sizes from 5P to 10P and upto 2.5 sq. mm

All sizes from 11P to 15P and upto 2.5 sq. mm

STRAIGHT THROUGH JOINTS

Supply and Making of heat shrinkable type straight through joints for 1100 volt grade power cables as per EIL standard specification No. 6-51-0051, including cutting, stripping of cable insulation complete with supply of compression / crimping type ferrules, plastic mould and epoxy resin compound etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 773 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2060.10.30

All sizes from 5P to 10P and upto 2.5 sq. mm

All sizes from 11P to 15P and upto 2.5 sq. mm

STRAIGHT THROUGH JOINTS

Supply and Making of heat shrinkable type straight through joints for 1100 volt grade power cables as per EIL standard specification No. 6-51-0051, including cutting, stripping of cable insulation complete with supply of compression / crimping type ferrules, plastic mould and epoxy resin compound etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Supply of heat shrinkable type Straight through jointing kits for Unearthed grade H.V. cables of the following sizes, as per EIL standard specification No. 6-51-0051, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

1 Core cable termination kit for 6.6 kV 630 mm²

1 Core cable termination kit for 11 kV 630 mm²

3 Core cable termination kit for 11 kV 240 mm²

SOR Sl. No.: 781 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2060.30.10V3

SOR Sl. No.: 782 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2060.30.20V1

SOR Sl. No.: 783 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2060.30.20V7

SOR Sl. No.: 784 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2060.40

SOR Sl. No.: 786 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2060.40.10V3

SOR Sl. No.: 788 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2060.40.20V10

SOR Sl. No.: 789 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2060.130

0-PK-SOR-3001-0-1M || ITEM NO: 01EE.2060.130.50

SOR Sl. No.: 792 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2060.130.40

SOR Sl. No.: 793 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2070

SOR Sl. No.: 794 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2070.10

SOR Sl. No.: 795 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2070.10.50

SOR Sl. No.: 796 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2070.10.70

SOR Sl. No.: 797 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2070.10.20

SOR Sl. No.: 798 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2080

SOR Sl. No.: 799 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2080.10

SOR Sl. No.: 800 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090

SOR Sl. No.: 801 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10

SOR Sl. No.: 802 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.450

SOR Sl. No.: 803 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.550

SOR Sl. No.: 804 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.560

SOR Sl. No.: 805 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.580

SOR Sl. No.: 806 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.590

SOR Sl. No.: 807 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.620

SOR Sl. No.: 808 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.630

SOR Sl. No.: 809 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.670

SOR Sl. No.: 810 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.700

SOR Sl. No.: 811 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.710

SOR Sl. No.: 812 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.720

SOR Sl. No.: 813 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.740

SOR Sl. No.: 814 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.760

SOR Sl. No.: 815 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.680

SOR Sl. No.: 816 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.10

SOR Sl. No.: 817 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.600

SOR Sl. No.: 818 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.640

SOR Sl. No.: 819 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.30

SOR Sl. No.: 820 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.470

SOR Sl. No.: 821 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.530

SOR Sl. No.: 822 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.570

SOR Sl. No.: 823 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.610

SOR Sl. No.: 824 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.650

SOR Sl. No.: 825 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.10.690

SUPPLY OF HV CABLES (SINGLE CORE)

1 C x 630 sq. mm, Al

SOR Sl. No.: 726 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2040

Supply of 6.6 KV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured single core cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

Supply of 11 KV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured single core cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 725 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2030.50.20

SOR Sl. No.: 829 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2090.30.20

SOR Sl. No.: 725 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2030.50.20

Supply of 11 KV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured single core cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

1 C x 630 sq. mm, Al

SOR Sl. No.: 726 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2040

SUPPLY OF HV CABLES (SINGLE CORE)

Supply of 6.6 KV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured single core cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 833 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2100

SOR Sl. No.: 725 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2030.50.20

Supply of 11 KV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured single core cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

1 C x 630 sq. mm, Al

SOR Sl. No.: 726 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2040

SUPPLY OF HV CABLES (SINGLE CORE)

Supply of 6.6 KV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured single core cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

3 C x 300 sq. mm, Al

SOR Sl. No.: 840 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2100.10.10

SOR Sl. No.: 841 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2100.30

SOR Sl. No.: 843 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2100.30.20

SOR Sl. No.: 845 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2100.30.40

SOR Sl. No.: 847 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2100.30.60

SOR Sl. No.: 848 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2100.40

SOR Sl. No.: 850 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2100.40.20

SOR Sl. No.: 852 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2100.40.40

SOR Sl. No.: 854 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2100.40.60

Supply and fixing of FLP(IIA/IIB) blocking plugs for blocking unused cable entries with following diameter in outdoor electrical equipment including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Cables with OD above 60 mm but upto 80 mm

Cables with OD above 30 mm but upto 40 mm

Cables with OD above 40 mm but upto 50 mm

Cables with OD above 50 mm but upto 60 mm

Cables with OD up to 20 mm

Cables with OD above 20 mm but upto 30 mm

MARKERS

Supply and installation of earth pit markers for directly buried GI pipe electrodes as per std. 7-51-0101 with 14 SWG enamelled steel plate engraved with white letters BURIED, EARTH ELECTRODE on JADE green background complete with support and foundation, including all labour and materials, as per approved drawings, specifications of this tender and direction of Engineer-in-Charge.

Cables with OD above 20 mm but upto 30 mm

Cables with OD up to 20 mm

Cables with OD above 50 mm but upto 60 mm

Cables with OD above 40 mm but upto 50 mm

MARKERS

SOR Sl. No.: 867 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2120.10

Cables with OD above 40 mm but upto 50 mm

Cables with OD up to 20 mm

Cables with OD above 20 mm but upto 30 mm

Cables with OD above 50 mm but upto 60 mm

MARKERS

All sizes upto 10 sq. mm

Cables with OD above 20 mm but upto 30 mm

Cables with OD above 50 mm but upto 60 mm

Cables with OD up to 20 mm

Cables with OD above 40 mm but upto 50 mm

MARKERS

SOR Sl. No.: 875 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2120.20.40

SOR Sl. No.: 877 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2120.20.30

Supply of crimping type long barrel Bimetallic lugs with Al barrel & tinned Cu palm with circular/sector shaped barrel for following conductor sizes, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 880 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2120.30.30

M || ITEM NO: 01EE.2120.30.40

SOR Sl. No.: 883 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2120.30.20

Supply of crimping type long barrel Bimetallic lugs with tinned Cu barrel & Al palm with circular/sector shaped barrel for following conductor sizes, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 886 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2120.40.10

SOR Sl. No.: 888 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2120.40.40

SOR Sl. No.: 890 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2120.40.50

SOR Sl. No.: 891 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2150

SOR Sl. No.: 892 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2150.10

SOR Sl. No.: 893 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160

SOR Sl. No.: 894 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.10

SOR Sl. No.: 895 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.10.10

SOR Sl. No.: 896 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.10.20

SOR Sl. No.: 897 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.10.30

SOR Sl. No.: 898 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.10.40

SOR Sl. No.: 899 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.10.50

SOR Sl. No.: 900 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.10.60

M || ITEM NO: 01EE.2120.30.40

Eqpt. Thread PG 13.5(DIN) - E.T. Thread 3/4" ET

Supply of crimping type long barrel Bimetallic lugs with tinned Cu barrel & Al palm with circular/sector shaped barrel for following conductor sizes, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 886 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2120.40.10

SOR Sl. No.: 888 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2120.40.40

SOR Sl. No.: 890 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2120.40.50

Eqpt. Thread PG 29 (DIN) -E.T. Thread 1-1/2" ET

SOR Sl. No.: 892 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2150.10

SOR Sl. No.: 893 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160

SOR Sl. No.: 894 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.10

SOR Sl. No.: 895 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.10.10

SOR Sl. No.: 896 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.10.20

SOR Sl. No.: 897 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.10.30

SOR Sl. No.: 898 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.10.40

SOR Sl. No.: 909 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.20.80

SOR Sl. No.: 910 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.30

Eqpt. Thread 1" PF (J.I.S.) -E.T. Thread 3/4"ET

SOR Sl. No.: 913 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.30.30

Eqpt. Thread 1" PF (J.I.S.) -E.T. Thread 3/4"ET

SOR Sl. No.: 916 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.30.60

SOR Sl. No.: 917 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.40

SOR Sl. No.: 919 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.40.20

SOR Sl. No.: 921 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.40.40

SOR Sl. No.: 923 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.2160.40.60

LIGHTING POLES

Supply and installation of Lighting Poles for floor mounting as per std. 7-51-0201, including all civil works, excavation, foundation, disposal of surplus earth, providing shoring, strutting and dewatering if required and including supply of cement, steel, GI pipes, base plates, paint and all sundry materials as required, including painting, (excluding supply and installation of control gear box/junction box), but including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Lighting poles including supply and connection of wires upto fixtures for safe areas.

-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.3020.20.10

SOR Sl. No.: 928 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.3020.30

Supply and installation of street lighting poles (single bracket/double bracket) including built in marshalling box and necessary wire/cable running from marshalling box to the lighting fixture, cable termination and connection, fixing of cable glands and lugs, including all civil works, excavation, foundation, disposal of surplus earth, providing shoring, strutting and dewatering if required and including supply of cement, steel, GI pipes, base plates, paint and all sundry materials as required, including painting, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Poles as per std. 7-51-0233 with MB as per 7-51-0208 for safe area

Poles as per std. 7-51-0234 sht. 2 of 2 (Single bracket)

HAZARDOUS AREA LIGHTING FIXTURES AND ACCESSORIES

Installation, connection, testing and commissioning of following types of flame proof/Div.2 lighting fixtures and accessories, including cable termination and connection, fixing of cable glands, lugs, including supply of necessary hardwares, including transportation from store/yard to site at the place of installation, unpacking, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

3-way, junction box.

4-way, junction box.

Well glass type pole mounting type for Ground Level.

Well glass type ceiling mounted.

Well glass type bracket mounted.

Well glass type pole mounting type for Platform.

Supply and installation of Type-`A' clamps(for bracket mounted lighting fixtures) including bolt (MOC SS304) for fixing the fixture to the clamp as per EIL std.no.7-51-0221, including supply and fixing of anchor fasteners, nuts and bolts, washers etc. as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Supply and installation of adapters for Platform and ground pole mounted lighting fixtures as per EIL std.no.7-51-0221, approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Supply and installation of Type-`B' clamps(for ceiling mounted lighting fixtures) including bolt (MOC SS304) for fixing the fixture to the clamps per EIL std.no.7-51-0221, including supply and fixing of anchor fastners,nuts and bolts,washers as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SAFE AREA LIGHTING FIXTURES

Supply, installation, testing and commissioning of following energy efficient lighting fixtures and connecting to wiring junction box/marshalling box complete with lamps and necessary control gear including supply of all connected materials like flexible conduit, clamps, supports, chains, anchor fastners, bolts, nuts and washers etc. as required, including supply and fixing of cable glands, lugs, including all labour and materials, as per approved drawings, data sheet for lighting fixture schedule, EIL installation standards, specifications of this tender and directions of Engineer-in-Charge.

Type LED SFD-12 Fixtures.

Type LED BK-3 Fixtures.

Type LED ST-10 Fixtures.

Type LED FD-1 Fixtures.

Type LED FD-2 Fixtures.

Type LED FD-3 Fixtures.

JUNCTION BOXES (OUTDOOR / INDOOR TYPE)

Supply and installation of dust and vermin proof G.I. sheet steel (1.6 mm thick) junction box WP type suitable for outdoor/indoor installation with number of outgoing ways as under, complete with PVC connectors, supply and fixing of cable glands, including supply of required size and number of terminals, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

2 C x 10 sq. mm

SUPPLY OF MV CABLES

Supply, installation, connection, testing and commissioning of flame proof weather proof lighting/power panels (for gas group IIA/IIB) as per EIL std. spec. 6-51-0008, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

2 C x 10 sq. mm

SOR Sl. No.: 958 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.3090.10.MB02

SOR Sl. No.: 959 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.3090.10.MB01

er) sheet steel enclosure having 4 pole incomer and single pole MCB (9 kA type) for outgoing circuit control with complete wiring, including cable termination, connection and fixing of cable glands, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

40 A, 4 pole incomer MCB isolator and 6 Nos. outgoing double pole MCBs (upto 20 A) with RCCBs in each outgoing circuits suitable for outdoor location with IP-65 degree of protection

40 A, 4 pole incomer MCB isolator and 12 Nos. outgoing double pole MCBs (upto 20 A) with RCCBs in each outgoing circuits suitable for outdoor location with IP-65 degree of protection

63 A, 4 pole incomer MCB isolator and 18 Nos. outgoing double pole MCBs (upto 20 A) with RCCBs in each outgoing circuits suitable for outdoor location with IP-65 degree of protection

WIRING

Circuit wiring in non-hazardous areas using (size given below), copper conductor, PVC insulated, FRLS outer sleeve cables (third core for earthing), from lighting/power panel/distribution junction box, excluding the supply of cable, junction boxes and cable glands but including termination and connection, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 966 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.3100.10.10

Circuit wiring in hazardous areas using (sizes given below) copper conductor, XLPE insulated, FRLS outer sleeve armoured cables (third core for earthing) from lighting/power panel/distribution junction box onwards, excluding the supply of cables, junction boxes and cable glands but including fixing of cable glands, supply and fixing of clamps, cable terminations and connections, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 969 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.3100.120.10

SOR Sl. No.: 970 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4020

Circuit wiring in non-hazardous areas using (size given below), copper conductor, PVC insulated, FRLS outer sleeve cables (third core for earthing), from lighting/power panel/distribution junction box, excluding the supply of cable, junction boxes and cable glands but including termination and connection, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 966 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.3100.10.10

Circuit wiring in hazardous areas using (sizes given below) copper conductor, XLPE insulated, FRLS outer sleeve armoured cables (third core for earthing) from lighting/power panel/distribution junction box onwards, excluding the supply of cables, junction boxes and cable glands but including fixing of cable glands, supply and fixing of clamps, cable terminations and connections, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 969 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.3100.120.10

SOR Sl. No.: 973 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4020.MC10

SOR Sl. No.: 974 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4020.MC10.10

SOR Sl. No.: 975 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4030

SOR Sl. No.: 976 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4030.10

SOR Sl. No.: 977 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4030.10.MC10

SOR Sl. No.: 978 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4030.10.30

SOR Sl. No.: 979 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4030.10.40

SOR Sl. No.: 980 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4030.10.20

SOR Sl. No.: 981 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4030.20

SOR Sl. No.: 983 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4030.20.30

SOR Sl. No.: 985 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4030.20.20

SOR Sl. No.: 986 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4040

SOR Sl. No.: 987 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4040.10

SOR Sl. No.: 988 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4040.10.10

SOR Sl. No.: 989 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4040.10.20

SOR Sl. No.: 990 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4040.10.30

SOR Sl. No.: 989 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4040.10.20

SOR Sl. No.: 994 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4040.30.30

SOR Sl. No.: 995 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4050

SOR Sl. No.: 996 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4050.10

SOR Sl. No.: 997 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4050.10.10

SOR Sl. No.: 998 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4070

SOR Sl. No.: 999 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4070.10

SOR Sl. No.: 1000 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4070.10.10

SOR Sl. No.: 1001 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4070.20

LIGHTNING RODS

Supply and installation of GI lightning rod as per std. 7-51-0503 including supply of all hardware etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

GI lightning rod as per std. 7-51-0503.

LAYING OF COMMUNICATION / FIRE ALARM CABLES

Horizontal and vertical laying/pulling through of communication/fire alarm cables of the following overall diameters in ready trays/trenches/conduits or supported on structures including supplying and fixing of GI saddle and saddle bars, stainless steel strip number tags, including transportation from store/yard to site at the place of installation, unpacking, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge

Cables of overall dia. above 35 mm.

Cables of overall dia. upto 35 mm.

Laying of HDPE ducts for laying of optical fiber cables between various substations, pulling through pipes or supported on structures including supplying and fixing of GI saddle and saddle bars, including supply and fixing of printed stainless steel/ non magnetic non corrosive metal tags, including transportation from store/yard to site at the place of installation, unpacking, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge

HDPE duct with overall dia. Upto 60mm

HDPE duct with overall dia. above 60mm

Laying of optical fiber cables between various buildings in already laid HDPE conduits for plant communication and fire alarm data highway, feeder differential protection, etc., including supply of all hardware, splice connectors, accessories, pulling through pipes or supported on structures including supply and fixing of printed stainless steel/ non magnetic non corrosive metal tags, including transportation from store/yard to site at the place of installation, unpacking, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Cables of overall dia. upto 40 mm.

Laying of optical fiber cables between various buildings in already laid HDPE conduits for plant communication and fire alarm data highway, feeder differential protection, etc., including supply of all hardware, splice connectors, accessories, pulling through pipes or supported on structures including supply and fixing of printed stainless steel/ non magnetic non corrosive metal tags, including transportation from store/yard to site at the place of installation, unpacking, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 1015 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.5040.30.20

Laying of optical fiber cables between various buildings in already laid HDPE conduits for plant communication and fire alarm data highway, feeder differential protection, etc., including supply of all hardware, splice connectors, accessories, pulling through pipes or supported on structures including supply and fixing of printed stainless steel/ non magnetic non corrosive metal tags, including transportation from store/yard to site at the place of installation, unpacking, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Making of straight through joints for polyethylene insulated armoured jelly filled/ non filled overall PVC jacketed, including supply of all necessary materials for the joint, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

For Non-Jelly filled cables of size .9 mm 5 pair

Horizontal and vertical laying/pulling through of communication/fire alarm cables of the following overall diameters in ready trays/trenches/conduits or supported on structures including supplying and fixing of GI saddle and saddle bars, stainless steel strip number tags, including transportation from store/yard to site at the place of installation, unpacking, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge

SOR Sl. No.: 1019 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.5050.10.20V2

SOR Sl. No.: 1020 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.5050.10.20V12

SOR Sl. No.: 1021 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.5050.10.30V1

SOR Sl. No.: 1022 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.5050.10.40V5

HDPE duct with overall dia. Upto 60mm

6 Fiber

Supply of straight through jointing kit for Multi mode, multitube/unitube, jelly filled, Optical fiber cable with non metallic armour with following number of fibers, as per EIL standard specifications, data sheet, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 1026 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.5050.30.10

SOR Sl. No.: 1027 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.5050.40

SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.5050.40.10

SOR Sl. No.: 1029 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.5060

SOR Sl. No.: 1030 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.5060.10

For Non-Jelly filled cables of size .9 mm 2 pair

For Non-Jelly filled cables of size .9 mm 50 pair

For Non-Jelly filled cables of size .63 mm 20 pair

For Non-Jelly filled cables of size 1.5 mm 2 pair

Laying of optical fiber cables between various buildings in already laid HDPE conduits for plant communication and fire alarm data highway, feeder differential protection, etc., including supply of all hardware, splice connectors, accessories, pulling through pipes or supported on structures including supply and fixing of printed stainless steel/ non magnetic non corrosive metal tags, including transportation from store/yard to site at the place of installation, unpacking, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Supply ,Installation, testing and commissioning of Fiber Optic Patch panel (LIU) for following type & number of fiber for OFCs including all accessories for terminating, pigtails with Connectors, patch cords with connectors, Splicing sleeves and splice tray including all labour and materials as per approved drawings specifications of this tender and directions of engineer-in-Charge

For 6 fiber Mono mode cable with LC pigtails and LC patch cords

For 6 fiber Mono mode cable with SC pigtails and LC patch cords

For 6 fiber Mono mode cable with ST pigtails and LC patch cords

For 6 fiber Mono mode cable with LC pigtails and SC patch cords

For 6 fiber Mono mode cable with LC pigtails and ST patch cords

For 6 fiber Mono mode cable with SC pigtails and SC patch cords

For 6 fiber Mono mode cable with SC pigtails and ST patch cords

For 6 fiber Mono mode cable with ST pigtails and SC patch cords

For 6 fiber Mono mode cable with ST pigtails and ST patch cords

Termination of optical fiber cables for various systems including supply of all hardware, splice connectors, accessories, including all labour and materials as per approved drawings specifications of this tender and directions of engineer-in-Charge

SOR Sl. No.: 1048 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.5060.30.10

Termination of optical fiber cables for various systems including supply of all hardware, splice connectors, accessories, including all labour and materials as per approved drawings specifications of this tender and directions of engineer-in-Charge

Supply of communication, fire alarm & control paired cables of following sizes as per EIL standard specification No. 6-51-0052, data sheet, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 999 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4070.10

SOR Sl. No.: 1000 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.4070.10.10

Jelly filled cables of size .9 mm 10 pair

Non-Jelly filled cables of size .9 mm 5 pair

Non-Jelly filled cables of size .9 mm 2 pair

Non-Jelly filled cables of size 1.5 mm 2 pair

Non-Jelly filled cables of size .9 mm 50 pair

Non-Jelly filled cables of size .63 mm 2 pair

Supply of Mono mode, jelly filled, Optical fiber cable with non metallic armour with following number of cores & construction, as per EIL standard specifications, data sheet, specifications of this tender and directions of Engineer-in-Charge.

6 Fiber multitube construction

Supply of Multi mode, jelly filled, Optical fiber cable with non metallic armour with following number of cores & construction, as per EIL standard specifications, data sheet, specifications of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 1061 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.5070.30.10

SOR Sl. No.: 1062 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.5070.40

SOR Sl. No.: 1064 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.5070.40.20

SOR Sl. No.: 1065 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.6010

SOR Sl. No.: 1066 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.6010.80

nch dimensions shall be measured).

Excavation and backfilling of trenches in all types of soil including rock.

Excavation and backfilling of trenches in all types of soil except rock.

Supply and laying of 40 mm size gravel in one layer of 100/150 mm thick including dressing of soil surface and laying the aggregate in uniform layer and density, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge ( Aggregate will be measured in boxes of size 1.5 m x 1.5 m x 0.5 m which shall be taken as 1 cubic metre, the boxes are to be furnished by the contractor free of cost for measuring purposes).

40 mm size gravel.

Supply and spreading of approved fine river sand/stone dust in cable trenches, including all labour and materials, specifications of this tender and directions of Engineer-in-Charge.

Fine river sand.

Supply and spreading of approved FLY ASH BRICKS - TYPE-5 of 75 mm thickness in cable trenches for cable protection, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. (Actual area of laid brick surfaces shall be measured).

Bricks.

Supply, fabrication and installation of 6 mm thick M.S. chequered plate for covering floor cut- outs/cable trenches etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

6 mm thick M.S. chequered plate.

Making through and through cut outs in pockets of following shape and size in the RCC floor/ walls of trenches/ buildings of thickness above 200 mm and upto 400 mm for facilitating cable/ duct entries, using concrete cutting machines and making cut out good using plastering and painting including all material and labour as per approved drawings, specification of this tender and directions of Engineer-in-charge.

Supply and spreading of approved FLY ASH BRICKS - TYPE-5 of 75 mm thickness in cable trenches for cable protection, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. (Actual area of laid brick surfaces shall be measured).

Bricks.

Supply, fabrication and installation of 6 mm thick M.S. chequered plate for covering floor cut- outs/cable trenches etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

6 mm thick M.S. chequered plate.

LAN SYSTEMS

Supply, installation, mounting, testing & commissioning of following Ethernet switches including performance warranty certification(for LAN) of 25 years through OEM, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge.

Etherswitch Rack Type-I

PAINTING & MARKING

Letter painting and marking of all buses of switchboards, all incomers, bus couplers, outgoings with details of Tag No, feeder rating in KW/Amp, sending end source, in the front of the panels and bus bar, panel nos.etc. on the rear side of the panels for all switchboards, all other substation equipment viz.transformers, capacitors, neutral grounding resistors, VFD panels, other panels, etc for equipment housed in electrical substations including supply of all material such as stickers, enamel paints, stencil, etc including supply of all labour, materials as per the specification of this tender and directions of Engineer-in-Charge.

Each alphabet/character above 2 inch and Upto 4 inch in height/length

Each alphabet/character upto 2 inch in height/length

Each alphabet/character above 4 inch and Upto 8 inch in height/length

Each alphabet/character above 8 inch and Upto 12 inch in height/length

Letter painting of tag nos., applicable circuit nos. for identification with red/black/white paint for all outdoor equipment in safe and hazardous areas viz. light fittings, control gear boxes, lighting/power panels, welding receptacles, convenience receptacles, local control stations, fire alarm manual call points, fire alarm detectors, motors, field call stations, loud speakers, etc. including supply of enamel paint, all hardware as required, supply of all labour, materials as per the specification of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 1091 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.9000.20.20

SOR Sl. No.: 1093 || PART NO: 0 || SOR NO: B861-000-16-50-PK-SOR-3001-0-1M || ITEM NO: 01EE.9000.20.30

INSTRUMENTATION

PRESSURE GAUGES AND ACCESSORIES (Incl. supply of Impulse pipe/Tubing material)

Installation of Line mounted or Remote mounted or Local Gauge Board mounted Pressure gauge/ Pressure gauge with Pulsation Dampener/ Syphon/ Overrange Protector (direct/ surface mounted/ diaphragm seal type) inclusive of mounting of instrument, supply of piping and tubing materials such as valves, fittings, pipes, tubes, compression fittings, as per specification, supply and erection of supports, mounting on support, (if support required), laying of capillary on supports, fabrication and installation of manifolds/ impulse lines with supports as per standards indicated below, hydraulic testing and painting of supports but exclusive of Supply of Instrument, Gauge Board, Yoke, and Calibration.

In Carbon Steel as per Standard 7-52-1103

In Carbon Steel as per Standard 7-52-4079.

DIFFERENTIAL PRESSURE GAUGES (Incl. supply of Impulse pipe/Tubing materials)

Installation of Differential Pressure gauge with/ without pulsation dampner/Syphon/ overrange protector including one side capillary type)/ Diaphragm seal type Differential Pressure gauge, surface/ yoke mounted inclusive of mounting of instrument, supply of piping & tubing materials such as valves, fittings, pipes, tubes, compression fittings as per specifications enclosed, supply and erection of supports, mounting on support, laying of capillary on supports, fabrication and installation of manifolds/ impulse lines with supports as per standards indicated below, hydraulic testing and painting of supports but exclusive of Supply of Instrument and Calibration

In Carbon Steel as per Standard 7-52-4077.

In Carbon Steel as per Standard 7-52-4078.

PRESS.INSTRUMENTS (Incl. supply of Impulse pipe/Tubing material)

Installation of Pressure Transmitters/ Pressure Switches (with or without Pulsation Dampener, Overrange Protector)/ Diaphragm seal type Pressure Transmitters/ Diaphragm seal type Pressure Switches including mounting on Yoke/ Surface, supply of piping & tubing materials such as valves, fittings, pipes, tubes, compression fittings as per specifications enclosed, supply of supports for capillary, supply and erection of supports for impulse lines wherever required, fabrication and installation of manifolds/ impulse lines with supports as per Standard indicated below, laying of capillary on supports, hydraulic testing and painting of supports but exclusive of Supply of Instrument, all Electrical/ Pneumatic connections, Yoke and Calibration.

In Carbon Steel as per Standard 7-52-1101

In Carbon Steel as per Standard 7-52-1159

In Carbon Steel as per Standard 7-52-1188

In Carbon Steel as per Standard 7-52-1102

In Carbon Steel as per Standard 7-52-1163

In Stainless Steel as per Standard 7-52-1159

DIFFERENTIAL PRESSURE INSTRUMENTS (Incl. supply of Impulse pipe/Tubing materials)

Installation of Differential Pressure Transmitters (including one side capillary type)/ Differential Pressure Switch(including one side capillary type)/ Diaphragm seal type DP Transmitters/ Diaphragm seal type DP Switch including mounting on Yoke/ Surface, supply of piping & tubing materials such as valves, fittings, pipes, tubes, compression fittings as per specifications enclosed, ,supply and erection of supports for impulse lines wherever required, fabrication and installation of manifolds/ impulse lines with supports as per Standard indicated below, supply and fabricating of supports for capillary, laying of capillary on supports, painting, installation of flushing connection, hydraulic testing of impulse lines as per standard indicated below but exclusive of Supply of Instrument, all Electrical/ Pneumatic connections, Yoke and Calibration.

In Carbon Steel as per Standard 7-52-1140

In Carbon Steel as per Standard 7-52-1192

DIFFERENTIAL PRESSURE (FLOW) TRANSMITTERS (Incl. supply of Impulse pipe/Tubing material)

Installation of Differential pressure(with or without integral manifold)/ Diaphragm Seal Type Differential Pressure flow instruments including Mounting on Yoke, supply of piping & tubing materials such as valves, fittings, pipes, tubes, compressive fittings as per specifications enclosed, supply of supports for impulse lines/ manifolds/ capillary, fabrication and Installation of manifolds/ impulse lines with supports as per Standard indicated below, laying of capillary on supports, hydraulic testing and painting of supports but exclusive of Supply of Instruments, all Electrical/ Pneumatic connections, Yoke and Calibration.

In Carbon Steel as per Standard 7-52-3489.

In Carbon Steel as per Standard 7-52-3490.

In Carbon Steel as per Standard 7-52-3491.

In Stainless Steel as per Standard 7-52-3490.

ULTRASONIC FLOWMETER

Installation of Transmitters/ Preamplifiers for ultrasonic flowmeters on yoke/ instrument (if required) including Straight length spool piece with pressure and temperature compensation loop including laying and termination of interconnection cable supports for cables as required, painting of supports but exclusive of supply of instrument, yoke and calibration.

Installation of Transmitters/ Preamplifiers for Ultrasonic Flowmeters

DIFFERENTIAL PRESSURE (LEVEL) TRANSMITTERS (Incl. supply of Impulse pipe/Tubing material)

Installation of DP type/ Diaphragm Seal DP type Level Instrument including mounting on Yoke, supply of piping & tubing materials such as valves, fittings, pipes, tubes, compressive fittings, as per specifications enclosed, supply of supports for impulse line/ capillary/ manifold, fabrication of manifolds and erection wherever required, laying of capillary on supports, fabrication and installation of impulse lines with support as per Standard indicated below, hydraulic testing and painting of supports but exclusive of Supply of Instrument, all Electrical/ Pneumatic connections, Yoke and Calibration.

In Carbon Steel as per Standard 7-52-1523.

In Carbon Steel as per Standard 7-52-1524.

LEVEL GAUGES (Incl. supply of Impulse pipe/Tubing material)

Installation of Level Gauges on Vessel/ Piping/ Standpipes with minor modification wherever required, supply of piping & tubing materials such as valves, fittings, pipes, tubes, compression fittings, as per specifications enclosed, fabrication of primary piping, fabrication and installation of drain valve/ vent valve assembly as per Standard indicated below, hydraulic testing of gauge, installation of illuminators/ non-frosting extension if required but exclusive of Supply of Gauges and Illuminators.

In Carbon Steel as per Standard 7-52-1527

SERVO TYPE TANK GAUGES

Installation/ interconnection of Servo type Gauges with/ without Tank Farm Management (TFM) System components. Installation of Gauge, Isolation ball valve, Calibration chamber on flanged equipment nozzle, with or without still well, Junction boxes with barriers, power switch, all Electrical connections but exclusive of Supply of Instrument, still well and Calibration/ Setting of gauges.

Servo Gauge Installation

RADAR LEVEL INSTRUMENTS

Installation of radar sensor and antenna, flanged type connection on equipment nozzle/ rail mounting with/without still well, but exclusive of supply of instruments. Installation of electronics units (total system for indication, transmission, marshalling etc. for one tank), including mounting on Yoke, supply of angle tray with supports, fabrication and erection of supports and laying of cable up to instrument/probe with clamps, termination of cables at both ends, but exclusive of supply of Instruments, supply of yokes and Calibration.

Installation of Top Mounted Radar

Installation of tank side indicator/electronic unit (total system for indication/ transmission/marshalling etc., as required for one tank) including mounting on yoke/support, fabrication and erection of supports, laying and termination of interconnecting cable up to instrument/ indicator with clamps, termination of cables at both ends, painting of supports but exclusive of supply of instruments, yoke, cables and calibration.

Tank Side Indicator

TEMPERATURE INSTRUMENTS

Installation of Temperature Indicators/ Gauges (Filled system/ Bimetallic) RTD/ Thermocouple/ Temperature Switches/ Temperature transmitters with flanged thermowell inclusive of installation of machined/ built-up thermowells on the nozzle and installation of Instruments, Electrical/ Pneumatic connection but exclusive of Supply of Instruments/ Elements/ Thermowell, and Calibration.

Temperature Indicator/ Gauges (Bimetallic Type) with thermowell on flanged wells

TEMPERATURE TRANSMITTERS (REMOTE MOUNTED)

Thermocouple/ RTD element with thermowell, along with Temperature Transmitter remote mounted. Installation of transmitter including mounting on yoke, fabrication and erection of supports with clamps and laying of extension/RTD cable upto thermocouple, termination of cables at both ends, painting of supports but exclusive of Supply of Instruments, Cable, Yoke and Calibration.

Temperature transmitter and RTD.

Temperature Transmitter and RTD with flanged well

Multipoint temperature transmitter with Thermocouple / RTD

MISCELLANEOUS ITEMS AND DEVICES

Mounting of Miscellaneous instrument items as listed below on Yoke; fabrication and erection of Supports and including installation of instrument items, painting of supports but exclusive of Supply of Instrument items, Piping/ Tubing material / Calibration and supply and erection of Yoke support.

ER probe assembly with accessories like flange, valve etc, if any, fixing of gaskets bolts/nuts wherever required and performing Positive Material Identification(PMI) using alloy analysers as per specification, drawings and directions of Engineer-in-Charge.

Corrosion coupon assembly with accessories like flange, valve etc, if any, fixing of gaskets bolts/nuts wherever required and performing Positive Material Identification(PMI) using alloy analysers as per specification, drawings and directions of Engineer-in-Charge.

Corrosion Transmitters

CALIBRATION/ TESTING

Cleaning, adjusting stroke/ positioner, stroke speed checking of Control and On-off (Shutdown) valves. Providing equipments, necessary test jig, Instrument Air, Nitrogen Cylinders, test reports, all consumable and loop testing. Excludes flow calibration

Control Valves

Self Actuated Pressure reducing valves

Cleaning, set pressure tests of Pressure Relief and Thermal Relief Valves. Providing equipment, necessary test jig, Instrument Air, Nitrogen Cylinders, test reports, all consumable. Excludes flow calibration.

Sizes upto 3/4" x 1" threaded

Inlet Sizes upto 2" flanged, rating 150# to 2500#

Cleaning, calibration of the instruments listed below including removal of instrument from reinstalled locations like pan

SOR Sl. No.: 1161 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.500.60

Corrosion coupon assembly with accessories like flange, valve etc, if any, fixing of gaskets bolts/nuts wherever required and performing Positive Material Identification(PMI) using alloy analysers as per specification, drawings and directions of Engineer-in-Charge.

Corrosion Transmitters

Cleaning, adjusting stroke/ positioner, stroke speed checking of Control and On-off (Shutdown) valves. Providing equipments, necessary test jig, Instrument Air, Nitrogen Cylinders, test reports, all consumable and loop testing. Excludes flow calibration

Differential Pressure Gauges

Differential Pressure Transmitters for Flow, Level and D.P.

Cleaning, set pressure tests of Pressure Relief and Thermal Relief Valves. Providing equipment, necessary test jig, Instrument Air, Nitrogen Cylinders, test reports, all consumable. Excludes flow calibration.

SOR Sl. No.: 1166 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.500.60.33

SOR Sl. No.: 1167 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.500.60.39

SOR Sl. No.: 1168 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.500.60.44

SOR Sl. No.: 1169 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.500.60.45

SOR Sl. No.: 1170 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.500.60.61

Inlet Sizes upto 2" flanged, rating 150# to 2500#

Ultrasonic flowmeters

LOOP CHECKING

Loop checking (excluding calibration/ testing) of the instruments listed below including verifying the functional performance of all elements comprising the loop, thereby ensuring proper interconnections and operation, with all other specifications inline with clause 4.13 of Standard specification for Erection tender 6-52-0060.

SOR Sl. No.: 1175 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.510.10.2

SOR Sl. No.: 1177 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.510.10.10

SOR Sl. No.: 1178 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.510.10.12

SOR Sl. No.: 1179 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.510.10.13

Speed / Vibration Transmitter

Control valve positioner

Corrosion Transmitter

Loop checking (excluding calibration/ testing) of the flowmeters listed below including verifying the functional performance of all elements comprising the loop, thereby ensuring proper interconnections and operation, with all other specifications inline with clause 4.13 of Standard specification for Erection tender 6-52-0060.

SOR Sl. No.: 1186 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.510.40.8

SOR Sl. No.: 1187 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550

SOR Sl. No.: 1188 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10

SOR Sl. No.: 1189 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD1

SOR Sl. No.: 1190 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD2

SOR Sl. No.: 1191 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD3

SOR Sl. No.: 1192 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD5

SOR Sl. No.: 1193 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD6

SOR Sl. No.: 1194 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD8

SOR Sl. No.: 1195 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD9

SOR Sl. No.: 1196 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD10

SOR Sl. No.: 1197 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD11

SOR Sl. No.: 1198 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD12

SOR Sl. No.: 1199 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD13

er Job specification for corrosion monitoring system document no.B861-000-06-42-CMS-0001.

Corrosion coupon system (Tag No. 701-CC-1701) with Corrosion Coupon Holder Assembly, 25 nos. of coupons for each corrosion coupon location as per data sheet no. B861-701-YI-DS- 3001 & as per Job specification for corrosion monitoring system document no.B861-000-06-42-CMS-0001.

Corrosion coupon system (Tag No. 701-CC-1801) with Corrosion Coupon Holder Assembly, 25 nos. of coupons for each corrosion coupon location as per data sheet no. B861-701-YI-DS- 3002 & as per Job specification for corrosion monitoring system document no.B861-000-06-42-CMS-0001.

Corrosion coupon system (Tag No. 701-CC-1901) with Corrosion Coupon Holder Assembly, 25 nos. of coupons for each corrosion coupon location as per data sheet no. B861-701-YI-DS- 3003 & as per Job specification for corrosion monitoring system document no.B861-000-06-42-CMS-0001.

Corrosion coupon system (Tag No. 701-CC-2001) with Corrosion Coupon Holder Assembly, 25 nos. of coupons for each corrosion coupon location as per data sheet no. B861-701-YI-DS- 3004 & as per Job specification for corrosion monitoring system document no.B861-000-06-42-CMS-0001.

Corrosion coupon system (Tag No. 701-CC-2101) with Corrosion Coupon Holder Assembly, 25 nos. of coupons for each corrosion coupon location as per data sheet no. B861-701-YI-DS- 3005 & as per Job specification for corrosion monitoring system document no.B861-000-06-42-CMS-0001.

24 V DC loop powered spare corrosion Transmitter.

Type: Non-contact type Radar Level Instrument (Tag No. 700-LT-1601)as per data sheet no.B861-700-YL-DS-2000 , Smart Transmitter with integral display , Power supply: 24 VDC Loop powered or separate 240V AC UPS Supply, Gauge Head: 6" Flanged connection / Top mounted, Flange Material: SS316, Accuracy: +/- 3mm, Output: 4-20 mA HART / 1/2" cable entry connection for signal & 3/4" cable entry connection for power (if applicable).

Type: Non-contact type Radar Level Instrument (Tag no. 700-LT-1602)as per data sheet no.B861-700-YL-DS-2001 , Smart Transmitter with integral display & local indicator, Power supply: 24 VDC Loop powered or separate 240V AC UPS Supply, Gauge Head: 6" Flanged connection / Top mounted, Flange Material: SS316, Accuracy: +/- 3mm, Output: 4-20 mA HART / 1/2" cable entry connection for signal & 3/4" cable entry connection for power (if applicable).

Type: Non-contact type Radar Level Instrument (Tag No. 701-LT-2201) as per data sheet no.B861-701-YL-DS-2000 , Smart Transmitter with integral display & local indicator, Power supply: 24 VDC Loop powered or separate 240V AC UPS Supply, Gauge Head: 8" Flanged connection / Top mounted, Flange Material: SS316 , Accuracy: +/- 3mm, Output: 4-20 mA HART / 1/2" cable entry connection for signal & 3/4" cable entry connection for power (if applicable).

Type: Non-contact type Radar Level Instrument (Tag No. 701-LT-2203) as per data sheet no.B861-701-YL-DS-2001 , Smart Transmitter with integral display, Power supply: 24 VDC Loop powered or separate 240V AC UPS Supply, Gauge Head: 6" Flanged connection / Top mounted, Flange Material: SS316, Accuracy: +/- 3mm, Output: 4-20 mA HART / 1/2" cable entry connection for signal & 3/4" cable entry connection for power (if applicable).

Type: Non-contact type Radar Level Instrument (Tag No. 701-LT-2204) as per data sheet no.B861-701-YL-DS-2002 , Smart Transmitter with integral display & local indicator, Power supply: 24 VDC Loop powered or separate 240V AC UPS Supply. Gauge Head: 6" Flanged connection / Top mounted , Flange Material: SS316, Accuracy: +/- 3mm, Output: 4-20 mA HART / 1/2" cable entry connection for signal & 3/4" cable entry connection for power (if applicable).

Type: Non-contact type Radar Level Instrument (Tag No. 851-LT-5501) as per data sheet no.B861-851-YL-DS-2000 , Smart Transmitter with integral display , Power supply: 24 VDC Loop powered or separate 240V AC UPS Supply, Gauge Head: 8" Flanged connection / Top mounted, Flange Material: SS316, Accuracy: +/- 3mm, Output: 4-20 mA HART / 1/2" cable entry connection for signal & 3/4" cable entry connection for power (if applicable).

Type: Non-contact type Radar Level Instrument (Tag No. 851-LT-5502) as per data sheet no.B861-851-YL-DS-2001 , Smart Transmitter with integral display & local indicator, Power supply: 24 VDC Loop powered or separate 240V AC UPS Supply. Gauge Head: 8" Flanged connection / Top mounted, Flange Material: SS316, Accuracy: +/- 3mm, Output: 4-20 mA HART / 1/2" cable entry connection for signal & 3/4" cable entry connection for power (if applicable).

Type: Servo Level Instrument (Tag No. 701-LT-2202) as per data sheet no.B861-701-YL-DS-2003 , Smart Transmitter with integral display , Power supply: 24 VDC Loop powered or separate 240V AC UPS Supply, Gauge Head: 6" Flanged connection / Top mounted, Flange Material: SS316, Accuracy: +/- 3mm, Output: 4-20 mA HART/ 1/2" cable entry connection for signal & 3/4" cable entry connection for power (if applicable).

Signal cable XLPE insulated FRLS 2 QUAD X1.5 mm2 as per data sheet no.B861-000-YS-DS-7006.

2"/300# Orifice plate & flange assembly as per Instrument data sheet no. B861-700-YF-DS-0002.

Signal cable FR 2 QUAD X1.5 mm2 as per data sheet no.B861-000-YS-DS-7009.

Industrial grade 4 1/2 digit digital Multimeter including accessories like battery, connecting pin, carry bag.

Industrial grade digital mA loop calibrator including accessories like battery, connecting pin, carry bag.

Industrial grade Multifunction calibrator with low , high pressure pump including accessories like charger, connecting pin, carry bag.

Universal hand-held HART communicators with accessories including charger, connecting pin, carry bag.

Differential Pressure (Flow) Transmitter-HART

SOR Sl. No.: 1222 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD36

SOR Sl. No.: 1223 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD37

SOR Sl. No.: 1224 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD38

SOR Sl. No.: 1225 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD39

SOR Sl. No.: 1226 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD40

SOR Sl. No.: 1227 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD41

SOR Sl. No.: 1228 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD42

SOR Sl. No.: 1229 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD43

SOR Sl. No.: 1230 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD44

SOR Sl. No.: 1231 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD45

SOR Sl. No.: 1232 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD46

SOR Sl. No.: 1233 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD47

SOR Sl. No.: 1234 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD49

SOR Sl. No.: 1235 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD50

SOR Sl. No.: 1236 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD51

SOR Sl. No.: 1237 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD52

SOR Sl. No.: 1238 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.MD53

SOR Sl. No.: 1239 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.57V1

SOR Sl. No.: 1240 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.10.57V2

SOR Sl. No.: 1241 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.20

SOR Sl. No.: 1242 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.20.1V2

SOR Sl. No.: 1243 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.20.1V3

SOR Sl. No.: 1244 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.30

SOR Sl. No.: 1245 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.30.5V1

SOR Sl. No.: 1246 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.30.5V3

SOR Sl. No.: 1247 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.30.5V4

SOR Sl. No.: 1248 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.40

SOR Sl. No.: 1249 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.40.3V1

SOR Sl. No.: 1250 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.40.3V3

SOR Sl. No.: 1251 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.40.3V4

SOR Sl. No.: 1252 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.50

SOR Sl. No.: 1253 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.50.1V2

SOR Sl. No.: 1254 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.50.1V4

SOR Sl. No.: 1255 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.50.1V5

SOR Sl. No.: 1256 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.50.MD1

SOR Sl. No.: 1257 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.50.3V1

SOR Sl. No.: 1258 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.50.4V1

SOR Sl. No.: 1259 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.50.6

SOR Sl. No.: 1260 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.70

SOR Sl. No.: 1261 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.70.2V2

SOR Sl. No.: 1262 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.70.2V3

SOR Sl. No.: 1263 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.110

Supply of 11 kV (UE) grade, Al/Cu Conductor, XLPE insulated and armoured cables of following sizes as per EIL standard specification No. 6-51-0051, data sheets, specifications of this tender and directions of Engineer-in-Charge.

10% of impulse piping / tubing material subject to minimum 1 number (1 meter for pipe / tube), whichever is higher, of each type, size, rating & material wise (such as valves, fittings, pipes, tubes, compression fittings as listed in the list of items of installation standard no. 7-52-3489, 7-52-3490, 7-52-3491, 7-52-1527, 7-52-1523,

SOR Sl. No.: 1265 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.110.MD1

SOR Sl. No.: 1266 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.110.2

SOR Sl. No.: 1267 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.110.3

SOR Sl. No.: 1268 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.110.4

SOR Sl. No.: 1269 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.110.5

SOR Sl. No.: 1270 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.110.6

SOR Sl. No.: 1271 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.110.7

SOR Sl. No.: 1272 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.110.8

SOR Sl. No.: 1273 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.110.9

SOR Sl. No.: 1274 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.550.110.10

SOR Sl. No.: 1275 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.600

SOR Sl. No.: 1276 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.600.MD1

SOR Sl. No.: 1277 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.600.MD2

Laying of instrumentation cables for signal, alarm, shutdown, control and signal cable on ducts, main trays, perforated trays, angle trays, trenches (including opening of cable duct covers if required through IRCs {Instrument Road Crossings}) including clamping, glanding the cables, termination at both ends including shield/ drain/ communication wire, providing and fixing identifying tags and megger testing but exclusive of supply of cables and erection of ducts, main tray, perforated tray/ angle trays and preparation of cable trench.

Signal / Alarm / Control Cables of cable sizes 1P x 1.5 / 2.5 mm²

Signal/ Alarm/ Control Cables of cable sizes 24C /12P x 1.5/ 2.5 mm²

Laying of power cables on ducts, main trays, perforated trays, angle trays, trenches (including through IRCs) including opening of cable duct covers if required clamping, glanding the cables, termination at both ends including shield/ drain/ communication wire providing and fixing of identifying tags and megger testing but exclusive of supply of multi cables and erection of ducts, main tray, perforated tray/ angle tray and preparation of cable trench

For cable size 2C x 2.5 mm²

EARTHING

Letter painting and marking of all buses of switchboards, all incomers, bus couplers, outgoings with details of Tag No, feeder rating in KW/Amp, sending end source, in the front of the panels and bus bar, panel nos.etc. on the rear side of the panels for all switchboards, all other substation equipment viz.transformers, capacitors, neutral grounding resistors, VFD panels, other panels, etc for equipment housed in electrical substations including supply of all material such as stickers, enamel paints, stencil, etc including supply of all labour, materials as per the specification of this tender and directions of Engineer-in-Charge.

SOR Sl. No.: 1285 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.650.10

SOR Sl. No.: 1286 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.650.10.MD1

SOR Sl. No.: 1287 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.700

SOR Sl. No.: 1288 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.700.2

SOR Sl. No.: 1289 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.700.2.2

SOR Sl. No.: 1290 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.700.3

SOR Sl. No.: 1291 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.700.3.4

SOR Sl. No.: 1292 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.700.7

SOR Sl. No.: 1293 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.700.7.5

SOR Sl. No.: 1294 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.700.50

SOR Sl. No.: 1295 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.700.50.MD1

SOR Sl. No.: 1296 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785

SOR Sl. No.: 1297 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.10

In Carbon Steel as per Standard 7-52-1101

In Carbon Steel as per Standard 7-52-1159

In Carbon Steel as per Standard 7-52-1188

SOR Sl. No.: 1300 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.20

In Carbon Steel as per Standard 7-52-1192

Sl. No.: 1301 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.20.MD1

SOR Sl. No.: 1302 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.20.MD2

SOR Sl. No.: 1303 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.30

SOR Sl. No.: 1304 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.30.MD1

SOR Sl. No.: 1305 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.30.MD2

SOR Sl. No.: 1288 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.700.2

In Carbon Steel as per Standard 7-52-1102.

SOR Sl. No.: 1297 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.10

SOR Sl. No.: 1308 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.30.MD5

SOR Sl. No.: 1309 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.40

SOR Sl. No.: 1310 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.40.MD1

SOR Sl. No.: 1311 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.40.MD2

SOR Sl. No.: 1312 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.50

SOR Sl. No.: 1314 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.50.MD2

Radiography conforming to the requirements of the Piping Class for all weld joints in impulse piping of Differential Pressure (Level) Instruments

SOR Sl. No.: 1317 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.60.MD1

SOR Sl. No.: 1318 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.60.MD2

SOR Sl. No.: 1319 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.85

SOR Sl. No.: 1320 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.85.MD1

SOR Sl. No.: 1321 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.786

SOR Sl. No.: 1322 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.786.MD1

In Stainless Steel as per Standard 7-52-1159.

SOR Sl. No.: 1325 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.786.50

SOR Sl. No.: 1326 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.786.50.MD1

SOR Sl. No.: 1327 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.790

SOR Sl. No.: 1328 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.790.10

SOR Sl. No.: 1329 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.790.10.1V5

SOR Sl. No.: 1330 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.790.20

SOR Sl. No.: 1331 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.790.20.1V3

SOR Sl. No.: 1332 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.790.20.1V5

SOR Sl. No.: 1333 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.790.20.MD1

SOR Sl. No.: 1334 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.790.20.MD2

SOR Sl. No.: 1335 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.800

SOR Sl. No.: 1336 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.800.20

SOR Sl. No.: 1337 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.800.20.1V3

SOR Sl. No.: 1332 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.790.20.1V5

SOR Sl. No.: 1333 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.790.20.MD1

SOR Sl. No.: 1334 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.790.20.MD2

SOR Sl. No.: 1336 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.800.20

SOR Sl. No.: 1340 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.800.81

SOR Sl. No.: 1341 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.800.81.1V1

SOR Sl. No.: 1342 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.800.81.1V2

SOR Sl. No.: 1343 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.800.81.1V3

SOR Sl. No.: 1344 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.800.81.1V5

SOR Sl. No.: 1345 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.802

SOR Sl. No.: 1346 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.802.20

SOR Sl. No.: 1347 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.802.20.1

SOR Sl. No.: 1348 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.802.20.3

SOR Sl. No.: 1349

FRP Canopy (All Side Closed) - Guided Wave , Mass Flow Meter

FRP Canopy for RTD / Thermocouple

Erection of Prefabricated FRP canopies for local instruments, Transmitters, Junction Box etc. on the stanchion and alignment as per standard 7-52-0105

SOR Sl. No.: 1353 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.802.26.1

SOR Sl. No.: 1355 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.802.26.4

FRP Canopy (All Side Closed) - Radar Level Instruments

GENERAL SITE WORK

Supply of Yoke supports for transmitters/ preamplifiers (wherever applicable) including supply, fabrication and erection of instrument yoke of all types and painting of yoke supports but exclusive of mounting of Instrument on supports.

2" Yoke supports as per standard 7-52-0101

Erection of 2" Yoke supports/ stanchions for Instruments but excluding supply and fabrication of Yoke support.

Erection of 2" Yoke supports for instruments excluding supply of Yoke

Supply, fabrication and installation of structural supports with MS channel/angle/plates etc. for supports of miscellaneous instruments/cabinets/panels including cutting, welding , bolting, rivetting, grouting including supply and installation of installation hardware like anchor bolts/nuts etc., painting of supports including supply of paints as per specification, including all labours and materials and completion of jobs in all aspects as per drawings/directions of Engineer-in-Charge nor paid).

Structural steel ISMC 100

Identification of instrument items wherever required including supply of approved colour of paint/ paints (Fluorescent), painting of tag number (approx 25-50 mm high) on instrument item like transmitter, switches, level gauges, control valves etc. as specified by Engineer-in-Charge.

Identification of instrument items

Supply, Fabrication & Installation of Concrete Pedestal (RCC) for supporting JB/Yoke but exclusive of supply of JB/Yoke as per specifications/drawing attached

Size 500 mm x 500 mm x 600 mm

SITE ACTIVITIES BY MECHANICAL CONTRACTOR

Supply & wrapping of single layer PIR Insulation (Cold conservation type insulation ) with thickness of 50mm for 1/2" impulse line consist of insulation blocks fixed with adhesives, joint sealants, protected from moisture/ water ingress by vapour barrier, vapour stop and covered with a weather protection jacket after cleaning the impulse lines of dust, rust, grease in line with Job specification for Insulation of piping & equipment ( B861-000-06-43-IL-S001 ) attached in the tender. The wrapping of the insulation around impulse line shall cover it completely without leaving any gap. Scope of supply & wrapping by Contractor includes all material, tools, tackles & labour etc. to complete the work in all respects.

Supply & wrapping of single layer PIR Insulation (Surface condensation type insulation ) with thickness of 25mm for 1/2" impulse line consist of insulation blocks fixed with adhesives, joint sealants, protected from moisture/ water ingress by vapour barrier, vapour stop and covered with a weather protection jacket after cleaning the impulse lines of dust, rust, grease in line with Job specification for Insulation of piping & equipment ( B861-000-06-43-IL-S001 ) attached in the tender. The wrapping of the insulation around impulse line shall cover it completely without leaving any gap. Scope of supply & wrapping by Contractor includes all material, tools, tackles & labour etc. to complete the work in all respects.

Transportation of all types of valves (Including Control Valves, Special Control Valves, Motor Operated Valves, PRDS, Control valves, On-Off/Shutdown valves, Self actuating valves) from Owner's storage points to contractor's stores/worksite and installation of valves for all rating including assembly of valves accessories like air bottles etc, if any, fixing of gaskets bolts/nuts wherever required and performing Positive Material Identification(PMI) using alloy analysers as per specification, drawings and directions of Engineer-in-Charge.

Inlet Valve size - 12" , Rating - 300#

Inlet Valve size - 1" , Rating - 300#

Inlet Valve size - 1 1/2" , Rating - 300#

Inlet Valve size - 3" , Rating - 300#

Transportation of all types of Safety Valves, Pilot Operated Safety Valves from owner's storage point to contractor's store/worksite and installation of valves for all ratings including assembly of valves, accessories if any, at all locations and fixing of gaskets, bolts/nuts wherever required as per drawings, specifications and as per the directions of engineer-in-charge.

Inlet size - 1" , Rating - 150#

Inlet size - 2" , Rating - 150#

Inlet size - 4" , Rating - 150#

Inlet size - 3/4" , Rating - NPT

Impulse line painting (uninsulated) as per painting specification for project

EM NO: 01II.950.13

SOR Sl. No.: 1383 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.950.13.1V1

SOR Sl. No.: 1384 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.950.14

SOR Sl. No.: 1385 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.950.14.1V1

SOR Sl. No.: 1386 || PART NO: 0 || SOR NO: B861-000-17-42-PK-SOR-3001-0-0M || ITEM NO: 01EW

SOR Sl. No.: 1387 || PART NO: 0 || SOR NO: B861-000-17-42-PK-SOR-3001-0-0M || ITEM NO: 01EW.17

SOR Sl. No.: 1388 || PART NO: 0 || SOR NO: B861-000-17-42-PK-SOR-3001-0-0M || ITEM NO: 01EW.17.1

SOR Sl. No.: 1389 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ

SOR Sl. No.: 1390 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ.ML1

SOR Sl. No.: 1391 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ.ML1.1

SOR Sl. No.: 1392 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ.ML1.2

SOR Sl. No.: 1393 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ.ML1.3

SOR Sl. No.: 1394 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ.ML1.4

SOR Sl. No.: 1395 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ.ML1.5

SOR Sl. No.: 1396 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ.ML2

SOR Sl. No.: 1397 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ.ML2.1

SOR Sl. No.: 1398 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ.ML3

SOR Sl. No.: 1399 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ.ML3.1

SOR Sl. No.: 1400 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ.ML3.2

SOR Sl. No.: 1401 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ.ML3.2.1

SOR Sl. No.: 1402 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ.ML3.2.2

SOR Sl. No.: 1403 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01QQ.ML3.2.3

SOR Sl. No.: 1404 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01RR

& field joints wherever required), levelling, aligning, fixation of foundation bolts, providing (including supply) packing / shim plates (as applicable), including chipping & dressing of foundations, grouting (including supply and application of grout material, equipment base frame filling as per vendor recommendation with specified grout), cleaning and flushing, draining and drying, purging of lines, and providing manpower and tools / equipment for NDT, testing, carrying out trial and start-up runs and testing under supervision of manufacture's / customer personnel, rectifying defects (if any), insulation (as applicable), precommissioning and commissioning (as applicable) and completing the work in all respects as per drawings, job specifications / scope of work and instructions of Engineer-in-charge for each equipment including drivers and accessories, as listed below. NOTE: Scope also includes erection, fabrication, insulation (as applicable), welding & field joints wherever required, installation & NDT of vendor supplied prefabricated spools / commercial length between various skids of an equipment package (payable at the rate provided against piping SOR items).

Pump Packages (all types) with drivers, auxiliaries and accessories.

All Types of Pumps (Electric Motor Driven) along with driver, auxiliaries and accessories (Single Skid).

Chemical Dosing Packages

Skid mounted chemical dosing packages along with all auxiliaries and accessories.

Procurement of Rotating Equipment Packages by Contractor. Engineering and Procurement of Rotating Equipment, handling and transportation of Rotating Equipment & miscellaneous items of equipment package from Owner's storage points to work site / contractor's stores, assembly of sub-assemblies, field assembly (as applicable) placing the equipment on foundations, (including some amount of cutting, welding & field joints wherever required), levelling, aligning, fixation of foundation bolts, providing (including supply) packing / shim plates (as applicable), including chipping & dressing of foundations, grouting (including supply and application of grout material, equipment base frame filling as per vendor recommendation with specified grout), cleaning and flushing, draining and drying, purging of lines, and providing manpower and tools / equipment for NDT, testing, carrying out trial and start-up runs and testing under supervision of manufacture's / customer personnel, rectifying defects (if any), insulation (as applicable), precommissioning and commissioning (as applicable) and completing the work in all respects as per drawings, job specifications / scope of work and instructions of Engineer-in-charge for each equipment including drivers and accessories, as listed below. NOTE: Scope also includes erection, fabrication, insulation (as applicable), welding & field joints wherever required, installation & NDT of vendor supplied prefabricated spools / commercial length between various skids of an equipment package (payable at the rate provided against piping SOR items).

Diesel Engine based Electric Generator Set Packages with auxiliaries and accessories.

Equipment Tag No. 701-DG-001 as per Document No. B861-000-80-42-SOW-3001

EQUIPMENT - STATIC

STORAGE TANKS

PLATE WORK

Plate work for Fixed Roof Tanks (Cone and Dome roof tanks) and covered Floating Roof tanks except Floating Roof: Procurement of all plates as per specifications, transportation to work site, fabrication and erection of shell, bottom (Sketch plates and annular plates including backing strips), cone roof, Dome roof, compression ring/knuckle plate, plate fabricated wind girders, wind girder opening, bearing plates for pipe supports, datum plates, shell manhole- necks, bolting and cover flanges for shell-man-holes, reinforcement pads for shell manholes, nozzle reinforcing pads, roof manhole-necks, bolting and cover flanges for roof manholes, reinforcing pads for Roof manholes, clean-out door assembly (including davit assembly), gusset- support for wind girders, Sump for drain nozzle, pads for all appurtenances and attachments, fabrication and installation of all items as per drawing, conducting tests such as vacuum test, MP/DP test, pneumatic test, oil penetrant examination, Grouting work (including the supply of grouting material, as required for the tanks installed on ring wall foundation) underneath the Annular/ bottom plate as per the specifications attached, tank hydrotest, etc. for shell, bottom and roof as specified, radiography including supply of films, all heat treatment specified in drawings/ specifications/ codes, preparation of drawings as per specifications, standards and relevant codes and getting the same reviewed by Owner/EIL, providing all temporary structures, clamps, wedges, including arrangement of all materials, consumables, labour, equipment, machinery, tools, tackles etc. to complete the work in all respects as per drawings, specifications, standards, codes, scope of work, scope of supply and instructions of Engineer- in-Charge. All bolting, gaskets wherever required as per scope of supply and scope of work shall be supplied and installed by Contractor. Spares 10% bolting (min. 2 nos.) and 200% spare gaskets shall be included in Contractors scope. Any other (Commissioning etc.) spares as mentioned in tender specifications shall be also be included in Contractor's scope. Quoted price shall be inclusive of supply of all bolts, nuts, gaskets including spares.

IS 2062 Gr. E250 (A, BR, B0, C)

STRUCTURAL/PIPES

STRUCTURAL/ PLATE WORK : Supply, fabrication, erection, inspection and testing of steel structure for cone roof/ dome roof supporting structure including curb angle, spiral stairway, cage ladder, handrail, top and intermediate platform, grating for stairway steps and platform, rolling ladder including track for floating roof, anchor chairs, name plates, earthing connections, ladder rungs for ladders in covered roof tanks, wind girder fabricated from rolled section, wind girder bracings/ support, external structural supports, supports for shell extension for foam nozzles in case of floating roof tanks, stiffeners for shell extension plate of stairway, ventilation slots and over flow slots for covered floating roof tank including SS wire mesh, preparation of drawings, getting the same reviewed/ approved by owner/ EIL, arrangement of all materials, consumables, labour, equipment/ machinery, tools and tackles required to complete the work as per drawings, specifications, standards, codes, scope of work, scope of supply and instructions of Engineer- in-Charge. All materials to be supplied by Contractor

SOR Sl. No.: 1420 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.2.1

SOR Sl. No.: 1421 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.2.1.1

SOR Sl. No.: 1422 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.2.1.1.ML01

SOR Sl. No.: 1423 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.2.1.1.1

SOR Sl. No.: 1424 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.2.1.1.2

SOR Sl. No.: 1425 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.2.2

SOR Sl. No.: 1426 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.2.2.ML01

SOR Sl. No.: 1427 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.2.2.1

SOR Sl. No.: 1428 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.2.3

SOR Sl. No.: 1429 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.2.3.1

SOR Sl. No.: 1430 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3

SOR Sl. No.: 1431 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1

SOR Sl. No.: 1432 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.ML01

SOR Sl. No.: 1433 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.1V10

SOR Sl. No.: 1434 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.1V15

SOR Sl. No.: 1435 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.1V17

SOR Sl. No.: 1436 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.1V19

SOR Sl. No.: 1437 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.1V21

SOR Sl. No.: 1438 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.ML02

SOR Sl. No.: 1439 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.ML03

SOR Sl. No.: 1440 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.ML04

SOR Sl. No.: 1441 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.ML05

SOR Sl. No.: 1442 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.ML06

SOR Sl. No.: 1443 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.ML08

SOR Sl. No.: 1444 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.ML09

SOR Sl. No.: 1445 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.4

SOR Sl. No.: 1446 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.3.1.4.1V9

SOR Sl. No.: 1447 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.4

SOR Sl. No.: 1448 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.4.1

SOR Sl. No.: 1449 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.4.1.1V1

SOR Sl. No.: 1450 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.4.1.1V2

SOR Sl. No.: 1451 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.4.1.1V3

SOR Sl. No.: 1452 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.4.1.1V4

SOR Sl. No.: 1453 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.4.1.1V6

SOR Sl. No.: 1454 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.8

SOR Sl. No.: 1455 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3

Diameter (Meters) : > 10 to 25 Height (Meters) : > 10

DESIGN, SUPPLY & INSTALLATION OF EMERGENCY VENT (Lumpsum) Design, engineering, manufacture, procurement of materials and bought out components, assembly at shop, inspection, testing at manufacturer's works, packing, delivery, documentation as per the enclosed M/s EIL specification and installation of Emergency Vent etc. to the satisfaction of the Engineer- in Charge.

DESIGN, SUPPLY & INSTALLATION OF BREATHER VALVE (Lumpsum): Design, engineering, manufacture, procurement of materials and bought out components, assembly at shop, inspection, testing at manufacturer's works, packing, delivery, documentation as per the enclosed EIL specification and installation of breather valves etc. to the satisfaction of the Engineer-in-charge.

Gauge Hatch with Cover: Supply & installation of "Gauge Hatch with Cover" for the tankages mentioned in the data sheets/ drawings/ specifications as per the Specifications & Standards attached with the tender. Arrangement of machinery, tools & tackles, labour etc. to accomplish the installation of the same shall also be in the scope of Contractor. The following Gauge Hatch with cover are required.

Material: CS

PAINTING OF TANKS

PAINTING FOR CARBON STEEL AND LOW ALLOY STEEL TANKS

DESIGN, SUPPLY & INSTALLATION OF BREATHER VALVE (Lumpsum): Design, engineering, manufacture, procurement of materials and bought out components, assembly at shop, inspection, testing at manufacturer's works, packing, delivery, documentation as per the enclosed EIL specification and installation of breather valves etc. to the satisfaction of the Engineer-in-charge.

SOR Sl. No.: 1463 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.101.1.1

SOR Sl. No.: 1464 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.101.1.1.4V30

SOR Sl. No.: 1465 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.101.1.2

SOR Sl. No.: 1466 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.101.1.2.1

SOR Sl. No.: 1467 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.101.1.2.4V27

SOR Sl. No.: 1468 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.101.1.4

SOR Sl. No.: 1469 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.101.1.4.1V44

SOR Sl. No.: 1470 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.10.101.1.4.1V45

SOR Sl. No.: 1471 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30

SOR Sl. No.: 1472 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30.ML01

SOR Sl. No.: 1473 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30.ML01.01

mblies, erection at all elevations, aligning, verticality checking, grouting, tightening of foundation bolts, welding of washer on anchor chairs, erection of wooden pillow for cold equipments, stacking of multi-tier exchanger(which are stored in unstacked condition), arranging hooks for test ring/ test flanges in heat exchangers, installation of demister, internal gratings, distributor, pipe davit, installation of mixer/agitator, cleaning and flushing by water, draining, drying by compressed air, arranging all tools, tackles, machinery, consumables, transportation equipment, erection equipment, instruments, labour, ancillary, etc. to complete the work in all respects as per drawings, equipment detail, specifications and instructions of the Engineer-in-Charge.

Equipment weighing less than 30 MT but 10 MT and above

TOUCH-UP PAINT APPLICATION (INSULATED EQUIPMENT) FOR CS VESSEL

Application of field primers and finish paint(Supply by Others) on C.S vessels, PHE and other equipment, including rubdown and touch up of shop primer (primer as per applicable specification) wherever required, as per attached specification, providing scaffolding for all heights, labour, materials, tools and tackles, consumables and supervision etc. to complete the work in all respect as per specifications, drawings, equipment details for painting and direction of Engineer in-Charge. The surface area is as per respective temperature ranges given in applicable specification. Note: Surface preparation, primer and finish paint shall be provided by equipment supplier.

EQUIPMENT UNLOADING: Unloading of Equipment from trailer at designated receiving point, Transportation of the same and handling over to owner at designated storage point for the following as per drawings, equipment detail, specifications and instructions of the Engineer-in-Charge.

Equipment weighing less than 50 MT but 30 MT and Above

EQUIPMENT UNLOADING: Unloading of Equipment from trailer at designated receiving point, Transportation of the same and handling over to owner at designated storage point for the following as per drawings, equipment detail, specifications and instructions of the Engineer-in-Charge.

SOR Sl. No.: 1319 || PART NO: 0 || SOR NO: B861-000-16-51-PK-SOR-3001-0-1M || ITEM NO: 01II.785.85

SOR Sl. No.: 1481 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30.7

SOR Sl. No.: 1482 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30.11

SOR Sl. No.: 1483 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30.11.4

SOR Sl. No.: 1484 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30.12

SOR Sl. No.: 1485 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30.12.4

SOR Sl. No.: 1486 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30.13

SOR Sl. No.: 1487 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30.13.1

SOR Sl. No.: 1488 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30.13.2

SOR Sl. No.: 1489 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30.13.4

SOR Sl. No.: 1490 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30.13.5

SOR Sl. No.: 1491 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30.13.11

SOR Sl. No.: 1492 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.30.13.12

SOR Sl. No.: 1493 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.40

SOR Sl. No.: 1494 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.40.2

ther than LNG.

Insulation Thickness: 50mm

Shells and heads of horizontal vessels, columns, reactors, exchangers, silencers etc and heads of above mentioned vertical equipments. Surface material: CS/AS. Insulation type: Ic (Polyurethane foam). Service: Other than LNG.

SOR Sl. No.: 1498 || PART NO: 0 || SOR NO: B861-000-80-42-PK-SOR-3001-0-3M || ITEM NO: 01VV.40.2.6.2

EARTH WORK (REFER SPECIFICATION NO. 6-68-0003)

Earthwork excavation in soil

Earth work in EXCAVATION below ground level for all kinds of works in ALL TYPES OF SOILS EXCEPT SOFT ROCK AND HARD ROCK as classified in specification for a depth upto 1.5m including removal of vegetation, shrubs and debris, cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, dewatering of accumulated water from any source and keeping the surface dry for subsequent works and disposal or stacking of excavated material within a lead of 100m, as directed including providing temporary supports to existing service lines like water pipes, sewage pipes, electric overhead and underground cables etc. all complete, but excluding shoring and strutting.

Earth work in EXCAVATION below ground level for all kinds of works in ALL TYPES OF SOILS EXCEPT SOFT ROCK AND HARD ROCK as classified in specification for a depth beyond 1.5m and upto and inclusive of 3.0m including removal of vegetation, shrubs and debris, cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, dewatering of accumulated water from any source and keeping the surface dry for subsequent works and disposal or stacking of excavated material within a lead of 100m, as directed including providing temporary supports to existing service lines like water pipes, sewage pipes, electric overhead and underground cables etc. all complete, but excluding shoring and strutting.

Earth work in EXCAVATION below ground level for all kinds of works in ALL TYPES OF SOILS EXCEPT SOFT ROCK AND HARD ROCK as classified in specification for a depth beyond 3.0m and upto & inclusive of 4.5m including removal of vegetation, shrubs and debris, cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, dewatering of accumulated water from any source and keeping the surface dry for subsequent works and disposal or stacking of excavated material within a lead of 100m, as directed including providing temporary supports to existing service lines like water pipes, sewage pipes, electric overhead and underground cables etc. all complete, but excluding shoring and strutting.

Earth work in EXCAVATION below ground level for all kinds of works in ALL TYPES OF SOILS EXCEPT SOFT ROCK AND HARD ROCK as classified in specification for a depth beyond 4.5m and upto & inclusive of 6.0m including removal of vegetation, shrubs and debris, cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, dewatering of accumulated water from any source and keeping the surface dry for subsequent works and disposal or stacking of excavated material within a lead of 100m, as directed including providing temporary supports to existing service lines like water pipes, sewage pipes, electric overhead and underground cables etc. all complete, but excluding shoring and strutting.

SHORING AND STRUTTING

Providing and installing approved type of "SHORING AND STRUTTING" by open timbering method for all depths to retain earth including dismantling and removal of the same etc. from site after completion of work etc. all complete as directed.

Providing and installing approved type of "SHORING AND STRUTTING" by close timbering method for all depths to retain earth including dismantling and removal of the same etc. from site after completion of work etc. all complete as directed.

Backfilling after execution of work

Transporting & Disposing the SURPLUS EARTH AND DEBRIS

Transporting and disposing the SURPLUS EARTH AND DEBRIS including shrubs and vegetations from construction area beyond the initial LEAD OF 100M AND UPTO 1KM including re-excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths and heights, stacking, levelling and dressing both the area (viz. from where the earth is transported and where it is deposited) to required levels and slopes complete with all lifts as directed. For carting on the basis of truck measurements (volume of truck reduced by 30% for voids).

Transporting and disposing the SURPLUS EARTH AND DEBRIS including shrubs and vegetations from construction area beyond the initial LEAD OF 1.0KM AND UPTO & INCLUSIVE OF 3.0KM including re-excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths and heights, stacking, levelling and dressing both the area (viz. from where the earth is transported and where it is deposited) to required levels and slopes complete with all lifts as directed. For carting on the basis of truck measurements (volume of truck reduced by 30% for voids).

PLAIN & REINFORCED CEMENT CONCRETE: (REFER SPECIFICATION NO. 6-68-0004)

PCC - Non FIM It

SOR Sl. No.: 1516 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.2.17

SOR Sl. No.: 1517 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.2.17.1

SOR Sl. No.: 1518 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.2.17.8

SOR Sl. No.: 1519 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.2.18

SOR Sl. No.: 1520 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.2.18.17

SOR Sl. No.: 1521 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.2.18.22

SOR Sl. No.: 1522 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.2.19

SOR Sl. No.: 1523 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.2.19.17

SOR Sl. No.: 1524 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.2.23

SOR Sl. No.: 1525 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.2.23.8

SOR Sl. No.: 1526 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.2.25

SOR Sl. No.: 1527 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.2.25.1

SOR Sl. No.: 1528 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.2.25.2

as specified and directed.

Providing and fixing CENTERING AND SHUTTERING for CURVED SHUTTERING in superstructures in all types of Structures such as Chimneys/Shafts/Silos/ tunnels/bunkers/hoppers /liquid storage structures/ domes etc. for all heights above plinth level including shuttering for single pour concreting, strutting, bracing, propping etc., keeping the same in position during concreting and removal of the same after specified period etc. for Straight/ Inclined Shuttering, keeping necessary provision for inserts, projecting dowels, anchor bolts or any other fixture etc. all complete and as specified and directed.

Fixing Re-bars in already cast concrete - Non FIM Items

Designing, supplying and fixing rebars in already cast concrete, including drilling, cleaning hole with air blow-out & wire-brush and injecting odourless Chemical of approved make, packed in dual foil, with the help of dispenser into a hole of diameter and depth as per manufacture specification, at all levels & locations for high strength deformed steel reinforcement bars of dia. 16 mm & 20 mm of Grade Fe500D (conforming to IS:1786), DESIGNED FOR FULL TENSILE ANCHORAGE, including testing (as per manufacturer's recommendations), adjusting and making good any damage done to the structure etc. all complete as specified and directed. SUPPLY OF ALL MATERIAL IN CONTRACTOR'S SCOPE EXCLUDING REINFORCEMENT BARS.

CONCRETE FOR LIQUID RETAINING/LEAK PROOF STRUCTURES (REFER SPECIFICATION NO.6-68-0005

RCC - Non FIM Items

Providing and laying Leak Proof Reinforced Cement Concrete of GRADE M-30 (minimum Cement content shall be as per EIL Specifications) with 20 mm and down size graded crushed stone aggregates/ gravel at all positions and in any shape and thickness, in SUB-STRUCTURE, leaving pockets, recesses, vibrating, tamping, curing, testing (for leak-proofness) and rendering (if required to give smooth and even surface) in foundations, walls , beams, buttresses, columns, piers, slabs, tunnels, basements, storage bins, reservoirs etc. including cement wash (if no other surface application is specified) but excluding the cost of Reinforcement, Shuttering and specified admixtures, all complete as specified and directed. ALL MATERIALS INCLUDING CEMENT SUPPLIED BY CONTRACTOR.

Water Proofing Comp. - Non FIM Items

Supplying and mixing of approved brand of integral WATER PROOFING COMPOUND in cement concrete, cement mortar etc. as per manufacturer's specifications or 1% by weight of cement (whichever is minimum), to make it leak proof/ water tight etc. all complete as specified and directed.

PVC Water bars - Non FIM Items

Supplying and fixing in position 230mm wide x 5mm thick approved PVC WATER STOPS as per manufacturer's specifications in R.C.C. Structures including cutting, fixing, jointing by vulcanising etc. all complete as shown specified and directed.

Separation Layer - NonFIM Item

Supplying and laying separating layer of approved polythylene sheet of mass 1 kg/sqm (minimum) in between base slab and the layer of lean concrete, including cleaning, preparing of surfaces, etc., all complete and as directed by the engineer-in-charge.

STRUCTURAL STEEL WORKS SPEC NO. 6-68-0006

General Steel Works - FIM Items

Transporting from storage yard (or any other location as specified by engineer-in-charge), Storing, Assembling and Erecting in position and testing/ examining, bolted and/ or welded, already Fabricated STRUCTURAL STEEL (of any Grade) at all locations and levels UPTO & INCLUSIVE OF 20 m ABOVE HPP/ FGL, including all builtup sections/ compound sections made out of rolled/ hollow sections and/or plates/ bent plates in all types of structural frameworks, fixing in line and level with temporary staging & bracing and removal of the same after erection, grouting with Ordinary Grout or premix free flow Nonshrink Grout as specified etc., all complete. ALREADY FABRICATED STRUCTURAL STEEL SHALL (WITH CONNECTION BOLTS) BE PROVIDED TO CONTRACTOR FREE OF COST. SUPPLY OF ALL OTHER MATERIAL IN CONTRACTOR'S SCOPE.

General Steel Works - Non FIM Items

Supplying, transporting, storing, fabricating & erecting in position and testing/ examining bolted and/ or welded STRUCTURAL STEEL WORKS of Grade E350BR / E350B0 (conforming to IS:2062) at all locations and levels UPTO & INCLUSIVE OF 20 m ABOVE HPP/ FGL, including all builtup sections/ compound sections made out of rolled sections and/ or plates/ bent plates in all types of structural frameworks, floor beams, stairs, or any other structural items or accessories to support equipments, piping, conveyor galleries, towers, masts, etc., but excluding silos, bunkers, hoppers, etc., cutting to required size, straightening/ bending if required, edge preparation, cleaning, preheating, bolting/ welding of joints, (including sealing the joints of box sections with continuous welding and plugging any open ends & holes of box sections), finishing edges by grinding, fixing in line and level with temporary staging & bracing and removal of the same after erection, grouting with Ordinary Grout or premix free flow Nonshrink Grout as specified, including preparation and submission of detailed fabrication drawings, preparing the surface for painting (SSPC-SP-10) and applying pre-erection/ shop primer (1 coat of F-9 @ 65-75 micron DFT) as per jOb Specification No. B861-000-06-42-PLS-01 after fabrication etc., all complete. SUPPLY OF ALL MATERIAL IN CONTRACTOR'S SCOPE.

Painting - Non FIM Items

Supplying and applying FIELD PAINT SYSTEM of approved quality and shade as per Sl. No. 5.2 of Table 5.0 of JOB Specification No. B861-000-06-42-PLS-01 over the coat of shop primer already applied, including storage, surface preparation, degreasing, cleaning, drying, providing necessary arrangement for access, testing etc. including touching up of shop primer coat as per Sl. No. 3.1 of Table 3.0 of JOB Specification No. B861-000-06-42-PLS-01 for steel structures (excluding ladders, spiral stairways & hand rails) at all location & levels, all complete as specified, in OFFISTE (COASTAL) areas as well as UNIT (INLAND & COASTAL) areas. SUPPLY OF ALL MATERIAL IN CONTRACTOR'S SCOPE. (Unit rate based on Structural steel weight).

3001-0-1M || ITEM NO: 01CS.4.4.MO1

SOR Sl. No.: 1549 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.4.4.MO2

SOR Sl. No.: 1550 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.5

SOR Sl. No.: 1551 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.5.7

SOR Sl. No.: 1552 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.5.7.MO1

SOR Sl. No.: 1553 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6

SOR Sl. No.: 1554 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6.15

SOR Sl. No.: 1555 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6.15.1

SOR Sl. No.: 1556 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6.16

SOR Sl. No.: 1557 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6.16.1

SOR Sl. No.: 1558 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6.17

SOR Sl. No.: 1559 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6.17.1

SOR Sl. No.: 1560 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6.18

SOR Sl. No.: 1561 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6.18.1

SOR Sl. No.: 1562 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6.19

SOR Sl. No.: 1563 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6.19.MO1

SOR Sl. No.: 1564 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6.19.6

SOR Sl

MS Rungs - Non FIM Items

Supplying, fabricating, fixing and keeping in position M.S. RUNGS in R.C.C. works at all depths and heights including handling, transporting the steel to site workshop and site of work, straightening, if required, cutting, bending to shape, necessary tying and welding with reinforcement, adjustment of shuttering, cleaning, surface preparation, shop primer as per EIL Spec. 6-79-0020 (or Job Specification, wherever applicable) and two coats of anticorrosive paint of approved quality on the exposed portion of rungs etc. all complete as specified and directed (SUPPLY OF ALL MATERIALS IN CONTRACTOR'S SCOPE).

Hand Railing 1000mm - Non FIM Items

Supplying, fabricating and fixing in position at all locations 1000mm high INCLINED HAND RAILING (for staircases) consisting of top rail, mid rail and vertical posts (Maximum spacing 1500mm c/c) with 32mm nominal diameter medium grade M.S. Tubes conforming to IS:1239 including straightening if required, cutting, bending, welding, bolting, grouting with ordinary grout, cleaning, surface preparation, hot-dip galvanising (80-85 micron as per IS:4759, IS:2629, IS: 4736, IS:2633), shop primer (1 coat of P6 of 40 micron) as per Sl. No. 4.1 of Table 4.0 of JOB SPEC. B861-000-06-42-PLS-01 preparation and submission of fabrication drawings etc. all complete as specified, shown and directed. (SUPPLY OF ALL MATERIALS IN CONTRACTOR'S SCOPE). (Complete handrail work shall be measured as length of top rail only and not length of each element fixed).

Supplying, fabricating and fixing in position at all locations 1000mm high HORIZONTAL HAND RAILING (for platforms, walkways, etc. or any other location as directed) consisting of top rail, mid rail and vertical posts (Maximum spacing 1500mm c/c) with 32mm nominal diameter medium grade MS Tubes conforming to IS:1239 and 100x5 MS Toe Plate confirming to IS:2062 (Grade A/B), including straightening if required, cutting, bending, welding, bolting, grouting with ordinary grout, cleaning, surface preparation, hot-dip galvanising (80-85 micron as per IS:4759, IS:2629, IS: 4736, IS:2633), shop primer (1 coat of P6 of 40 micron) as per Sl. No. 4.1 of Table 4.0 of JOB SPEC. B861-000-06-42-PLS-01, preparation and submission of fabrication drawings etc. all complete as specified, shown and directed. (SUPPLY OF ALL MATERIALS IN CONTRACTOR'S SCOPE). (Complete handrail work shall be measured as length of top rail only and not length of each element fixed).

Transporting from storage yard (or any other location as specified by engineer-incharge), Storing, Assembling and Erecting in position and testing/ examining, bolted and/ or welded, already Fabricated HAND RAILING for platforms etc. including straightening, cutting, bending (if required) welding, bolting, grouting with ordinary grout, all complete as specified and directed. ALREADY FABRICATED HANDRAILING (WITH CONNECTION BOLTS) SHALL BE PROVIDED TO CONTRACTOR FREE OF COST. SUPPLY OF ALL OTHER MATERIAL IN CONTRACTOR'S SCOPE. (Complete handrail work shall be measured as length of top rail only and not length of each element fixed)

Mechanical Anchor fastners - Non FIM Items

"Supplying, handling, transporting to site of work and fixing approved MECHANICAL ANCHOR FASTENERS M.S. bolts of Grade 5.8 or more, GALVANIZED with minimum thickness of 5 microns (approved for use in cracked concrete), of 12mm dia at specified positions on concrete floors, roofs, beams (sides and bottom), walls, columns etc. according to manufacturer's specifications including all accessories like nuts, washers etc. of required size, testing, necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air blowout & wire-brush, and making good any damage done to the structure etc. all complete for all heights, depths and locations as specified and directed. "

"Supplying, handling, transporting to site of work and fixing approved MECHANICAL ANCHOR FASTENERS M.S. bolts of Grade 5.8 or more, GALVANIZED with minimum thickness of 5 microns (approved for use in cracked concrete), of 16mm dia at specified positions on concrete floors, roofs, beams (sides and bottom), walls, columns etc. according to manufacturer's specifications including all accessories like nuts, washers etc. of required size, testing, necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air blowout & wire-brush, and making good any damage done to the structure etc. all complete for all heights, depths and locations as specified and directed. "

Chemical Anchor Fastner

"Supplying, handling, transporting to site of work and fixing approved CHEMICAL ANCHOR FASTENERS consisting of M.S. threaded rod of Grade 5.8, GALVANIZED with minimum thickness of 5 microns and chemical (approved for use in cracked concrete), packed in flexible chemical foil or dual foil type, to be used with the help of dispenser, of 12mm dia. at specified positions on concrete floors, roofs, beams (sides and bottom), walls, columns etc. according to manufacturer's specifications including all accessories like nuts, washers etc. of required size, testing, necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air blowout & wire-brush and making good any damage done to the structure etc. all complete for all heights, depths and locations as specified and directed. "

"Supplying, handling, transporting to site of work and fixing approved CHEMICAL ANCHOR FASTENERS consisting of M.S. threaded rod of Grade 5.8, GALVANIZED with minimum thickness of 5 microns and chemical (approved for use in cracked concrete), packed in flexible chemical foil or dual foil type, to be used with the help of dispenser, of 16mm dia. at specified positions on concrete floors, roofs, beams (sides and bottom), walls, columns etc. according to manufacturer's specifications including all accessories like nuts, washers etc. of required size., testing, necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air blowout & wire-brush and making good any damage done to the structure etc. all complete for all heights, depths and locations as specified and directed. "

"Supplying, handling, transporting to site of work and fixing approved CHEMICAL ANCHOR FASTENERS consisting of M.S. threaded rod of Grade 5.8, GALVANIZED with minimum thickness of 5 microns and chemical (approved for use in cracked concrete), packed in flexible chemical foil or dual foil type, to be used with the help of dispenser, of 20mm dia. at specified positions on concrete floors, roofs, beams (sides and bottom), walls, columns etc. according to manufacturer's specifications including all accessories like nuts, washers etc. of required size., testing, necessary scaffolding, d

SOR Sl. No.: 1578 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6.26.3

SOR Sl. No.: 1579 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6.27

SOR Sl. No.: 1580 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.6.27.1

SOR Sl. No.: 1581 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.7

SOR Sl. No.: 1582 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.7.9

SOR Sl. No.: 1583 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.7.9.1

SOR Sl. No.: 1584 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.7.9.2

SOR Sl. No.: 1585 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.7.11

SOR Sl. No.: 1586 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.7.11.1

SOR Sl. No.: 1587 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.10

SOR Sl. No.: 1588 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.10.1

SOR Sl. No.: 1589 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.10.1.1

SOR Sl. No.: 1590 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.10.1.2

SOR Sl. No.: 1591 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.10.2

SOR Sl. No.: 1592 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.10.2.1

SOR Sl. No.: 1593 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.10.2.2

SOR Sl. No.: 1594 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.10.2.3

SOR Sl. No.: 1595 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.10.2.12

block foundations, raft foundations, pile caps, mass concrete, equipment foundations etc. by using vibration-less spark-free Diamond Wire Saw Cutter of make HILTI (or equivalent) at all depths & heights, in hazardous areas within process units & offsite which are fire prone due to presence of hydrocarbon vapours etc. taking elaborate precautions for dismantling as per fire permit, clearance etc. and work is to be done with extreme caution. The work item includes cost of all necessary accessories, tools & tackles including diamond saw cutter , disposal of RCC Debris upto lead of 100 m & for all lifts (taking all safety precautions) including cutting reinforcement bars, embedded structural steel members, with necessary scaffolding, propping and underpinning etc. for all elevations with all labour and materials complete as per drawings, specificationsand directions of the Engineer-in-charge. Payment will be made per sq.m.of cross-sectional cut area. Contractor to submit dismantling plan prior to start of dismantling. Dismantling shall be planned in such a way that each cut piece shall weigh not less than 1.6 MT.

Pockets - Non FIM Items

Making POCKETS/HOLES of sizes upto & inclusive of 200 x200x500mm in RCC/PCC works (taking all necessary safety precautions) by chiselling/drilling, including supply of all tools & tackles, necessary scaffolding etc. cutting of reinforcement bars, cleaning the pockets of all debris, disposal of the unserviceable material to spoil heaps anywhere within the plant boundary all complete at all heights & depths as specified and directed.

PCC _ Non FIM Items

Demolishing PLAIN CEMENT CONCRETE work (taking all necessary safety precautions) for all depths below plinth level including supply of all tools & tackles, necessary scaffolding, propping, underpinning etc. disposal of unserviceable material to spoil heaps anywhere within the plant boundary, all complete as specified and directed. (Excavation and backfilling shall be paid separately under relevant items)

Demolishing PLAIN CEMENT CONCRETE work (taking all necessary safety precautions) for all depths below plinth level including supply of all tools & tackles, necessary scaffolding, propping, underpinning etc. stacking of all the demolished concrete material at a designated location within the complex limits, all complete as per specifications and directions of Engineer-in-Charge for further processing in mechanical crushers for generating RA/ RCA as per the specifications. (Excavation & backfilling shall be paid separately under relevant items).

Steelwork - Non FIM Items

Dismantling bolted/rivetted/welded STRUCTURAL STEEL WORK of all descriptions (taking all necessary safety precautions), including supply of all tools and tackles, consumables, necessary scaffolding etc., providing temporary bracings as required, cutting (by flame or saw) gusset plates, bolts, nuts, weldings etc., transporting and stacking of the serviceable materials, cleaning the site of work of all unserviceable materials for disposal to spoil heaps anywhere within the plant boundary, all complete at all depths and heights, as specified and directed.

MISCELLANEOUS ITEMS (REFER SPECIFICATION NO. 6-68-0013)

Anticorrosive - Non FIM Items

Providing and laying 50mm thick ANTI-CORROSIVE LAYER under steel storage tanks with screened dry coarse sand mixed with A90 grade bitumen conforming to IS:73 including mixing in drum, heating to the required temperature, with 3% kerosene if required, tamping, dressing to the required slopes to form hard mass of specified compacted thickness etc. all complete as directed.

Sand Filling - Non FIM Items

Supplying and filling approved SAND of specified quality under floors, in foundations, plinths, tank foundations etc. for all depths and heights including cost of sand, royalties, transportation to site for all leads and lifts, including loading, unloading, spreading in layers of loose thickness not exceeding 150 mm, watering, ramming, compacting with mechanical compactors and/or other equipment to the specified levels to achieve 85% relative density as per IS:2720 Part XIV, including preparation of subgrade to the required slope, providing testing apparatus and testing the degree of consolidation all complete as per drawings, specifications and direction of Engineer-in-charge. The rates shall be inclusive of the cost of all labour, material, equipments etc. all complete .

BI-POLAR CONCRETE PENETRATING CORROSION INHIBITING ADMIXTURE

Supplying and mixing of approved brand of BI-POLAR CONCRETE PENETRATING CORROSION INHIBITING ADMIXTURE (confirming to EIL Specification No. 6-68-0017) in concrete as per manufacturer's specification for protection of reinforcement against corrosion. Supply of admixture in Contractor's scope.

BONDING FRESH CONCRETE TO OLD CONCRETE BY EPOXY RESIN BONDING SYSTEM (REFER SPECIFICATION NO. 6-68-0056)

Epoxy Resin - non FIM Items

Providing and applying approved EPOXY RESIN (prepared as per manufacturer's recommendation) for bonding of fresh concrete to old concrete in all types of structure at all depths and heights including cleaning of concrete surface, removing of all loose concrete pieces, making rough by chiselling, taking off the skin of concrete, application of Epoxy Resin System by spraying, necessary working platforms, props, scaffolding and other safety measures, removal of same after completion etc. all complete as specified and directed. (Excavation, backfilling, removal of surplus earth, keeping pit dry by pumping/bailing subsoil water shall be paid separately under relevant items).

FIREPROOFING OF STEEL STRUCTURES (REF SPEC NO 6-68-0033)

Concrete - Non FIM Items

Supply and laying of concrete of grade M30 as per Type-I of EIL Standard Specification 6-68-0033 as fire proofing material with 10 mm and down size graded coarse and fine aggregates including admixture around structural steel members (viz. beams, columns, bracings etc.) all complete; cleaning the steel surfaces, supplying, placing and fixing in position cover plates conforming to IS:2062 and stiffeners for members exceeding 600 mm depth, supply and welding of MS nuts

SOR Sl. No.: 1616 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01CS.17.11.1

Epoxy Resin - non FIM Items

Supply and laying of vermiculite based lightweight cementitious concrete coating as per Type-II of EIL Standard Specification 6-68-0033 as fire proofing material of required thickness around structural steel members (viz. beams, columns, bracings etc.) for the required fire protection from reaching temperature 538 degree C; cleaning the steel surfaces and applying primer compatible to vermiculite material if required as per manufacturer specifications, supplying, placing and fixing in position cover plates conforming to IS:2062 and stiffeners for members exceeding 600 mm depth, supply and welding of MS nuts on angle and box sections and cover blocks for other sections, supplying, placing and fixing in position galvanized expanded metal sheet with mesh size 4.5 mm x 13.5 mm conforming to IS:412 except on angle and box sections, hot dipped galvanized welded wire fabric reinforcement 2 mm dia 50 mm x 50 mm mesh conforming to IS:1566, and tying the reinforcement to the cover blocks with galvanized 16 SWG tying wire, including cutting, straightening, cleaning, bending, applying primer on MS nuts and affected surfaces, curing or providing a layer of approved membrane of curing compound, patching of damaged portion wherever required to achieve a smooth and even surface, providing chamfering at corners, supplying and laying of non-bituminous polysulfide or silicon rubber mastic sealant at terminating edges/ metal joints, painting the surfaces with sealer coat of epoxy polyamide as base and finish coats of coating system No.1 of NORSOK Standard M-501, including the cost of all labour, materials, specified tests, shuttering, staging, scaffolding, working platforms, approaches, etc. for all shapes and positions at all heights upto & including 10 m above pavement etc. all complete as per specifications and directions of Engineer-in-Charge. (ALL MATERIALS SHALL BE SUPPLIED BY THE CONTRACTOR).

Supply and laying of vermiculite based lightweight cementitious concrete coating as per Type-II of EIL Standard Specification 6-68-0033 as fire proofing material of required thickness around structural steel members (viz. beams, columns, bracings etc.) for the required fire protection from reaching temperature 538 degree C; cleaning the steel surfaces and applying primer compatible to vermiculite material if required as per manufacturer specifications, supplying, placing and fixing in position cover plates conforming to IS:2062 and stiffeners for members exceeding 600 mm depth, supply and welding of MS nuts on angle and box sections and cover blocks for other sections, supplying, placing and fixing in position galvanized expanded metal sheet with mesh size 4.5 mm x 13.5 mm conforming to IS:412 except on angle and box sections, hot dipped galvanized welded wire fabric reinforcement 2 mm dia 50 mm x 50 mm mesh conforming to IS:1566, and tying the reinforcement to the cover blocks with galvanized 16 SWG tying wire, including cutting, straightening, cleaning, bending, applying primer on MS nuts and affected surfaces, curing or providing a layer of approved membrane of curing compound, patching of damaged portion wherever required to achieve a smooth and even surface, providing chamfering at corners, supplying and laying of non-bituminous polysulfide or silicon rubber mastic sealant at terminating edges/ metal joints, painting the surfaces with sealer coat of epoxy polyamide as base and finish coats of coating system No.1 of NORSOK Standard M-501, including the cost of all labour, materials, specified tests, shuttering, staging, scaffolding, working platforms, approaches, etc. for all shapes and positions at all heights more than 10 m above pavement etc. all complete as per specifications and directions of Engineer-in-Charge. (ALL MATERIALS SHALL BE SUPPLIED BY THE CONTRACTOR).

Vermiculite Concrete for Equipments - Non-FIM Items

Supply and laying of vermiculite based lightweight cementitious concrete coating as per Type-III of EIL Standard Specification 6-68-0033 as fire proofing material of required thickness on equipment/ vessel skirts, saddles and supports for the required fire protection from reaching temperature 427 degree C; cleaning the steel surfaces and applying primer compatible to vermiculite material if required as per manufacturer specifications, supplying, placing and fixing in position cover plates conforming to IS:2062, hot dipped galvanized welded wire fabric reinforcement of 2 mm dia 50 mm x 50 mm mesh conforming to IS:1566 and tying the reinforcement with the pre welded nuts by galvanized 16 SWG tying wire, including straightening, cutting, bending of the reinforcement, including supplying and welding of additional MS nuts if directed by the Engineer-in-charge, applying primer wherever required, curing or providing a layer of approved membrane of curing compound, patching of damaged portion wherever required to achieve a smooth and even surface, providing chamfering at corners, supplying and laying of non-bituminous polysulfide or silicon rubber mastic sealant at terminating edges/ metal joints, painting the surfaces with sealer coat of epoxy polyamide as base and finish coats of coating system No.1 of NORSOK Standard M-501, including the cost of all labour, materials, specified tests, shuttering, staging, scaffolding, working platforms, approaches, etc. for all shapes and positions. all complete as per specifications and directions of Engineer-in-Charge. (ALL MATERIALS SHALL BE SUPPLIED BY THE CONTRACTOR).

Mechanical works

Supplying, fabricating and erecting in position MS plates as per detailed drawings, conforming to grade A of IS:2062 on top of all RCC pedestals supporting the sliding saddles of equipments, including cutting, straightening where necessary, rounding rounding unfinished edges by grinding, machining the exposed top surface, making necessary bolt holes, providing and laying ready mixed free flow non-shrink grout below the base plate at all levels & locations, machining top surfaces etc. all complete and as shown and directed.

SAFETY (REFER EIL SPECIFICATION)

Safety Structures - Non FIM Items

Supplying, Transporting, Storing, Fabricating & Erecting in position and testing/ examining bolted and/ or welded Structural Steel Works at all locations and levels in HANGER SCAFFOLDING below piperack, comprising of hangar channels, fabricated pen wen ladder beams, steel planks bent to shape and size and any other sections, if required, all as per sketches/ specifications and load tested for statisfactory performance, including cutting to required size, straightening/ bending if required, edge preparation, cleaning, preheating, bolting/ welding of joints (including sealing the joints of box sections with continuous welding and plugging any open ends & holes of box sections), finishing edges by grinding, fixing in line and level with temporary staging & bracing and removal of the same after erection, including preparation and submission of detailed fabrication drawings, preparing the surface for painting as per BIS codes after fabrication etc. all complete as specified and directed. All items shall be removed & carried back by Contractor as per instructions of Engineer-in-Charge after completion of works. (Supply of All Material In Contractor's Scope).

Providing and fixing double scaffolding system of any height made with 40 mm dia MS tube 1.5 m centre to centre, horizontal & vertical tubes joining with MS tubes, MS tube challies, MS clamps and MS staircase system in the scaffolding for working platform/ staircase etc., and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc., wherever required for inspection of work at required locations with essential safety features for the workmen etc., all complete as per directions and approval of Engineer-in-charge. (Height shall be measured from Floor/ platform from where scaffolding is erected) including providing Aluminium ladders for safe acess of workers.

Supply of Safety Personnel

Supply of HSE personnel SAFETY STEWARD over and above the requirement as specified in EIL Standard Specification No. 6-82-0001 at site as per the written instructions of Engineer-in-charge (the rates shall be inclusive of all other payments such as PF, ESI, other benefits payable to the workmen as per the prevalent labour laws).

Supply of HSE personnel SAFETY SUPERVISOR over and above the requirement as specified in EIL Standard Specification No. 6-82-0001 at site as per the written instructions of Engineer-in-charge (the rates shall be inclusive of all other payments such as PF, ESI, other benefits payable to the workmen as per the prevalent labour laws).

Supplying, Transporting, Storing, Fabricating & Erecting in position and testing/ examining bolted and/ or welded Structural Steel Works at all locations and levels in HANGER SCAFFOLDING below piperack, comprising of hangar channels, fabricated pen wen ladder beams, steel planks bent to shape and size and any other sections, if required, all as per sketches/ specifications and load tested for statisfactory performance, including cutting to required size, straightening/ bending if required, edge preparation, cleaning, preheating, bolting/ welding of joints (including sealing the joints of box sections with continuous welding and plugging any open ends & holes of box sections), finishing edges by grinding, fixing in line and level with temporary staging & bracing and removal of the same after erection, including preparation and submission of detailed fabrication drawings, preparing the surface for painting as per BIS codes after fabrication etc. all complete as specified and directed. All items shall be removed & carried back by Contractor as per instructions of Engineer-in-Charge after completion of works. (Supply of All Material In Contractor's Scope).

Providing and fixing double scaffolding system of any height made with 40 mm dia MS tube 1.5 m centre to centre, horizontal & vertical tubes joining with MS tubes, MS tube challies, MS clamps and MS staircase system in the scaffolding for working platform/ staircase etc., and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc., wherever required for inspection of work at required locations with essential safety features for the workmen etc., all complete as per directions and approval of Engineer-in-charge. (Height shall be measured from Floor/ platform from where scaffolding is erected) including providing Aluminium ladders for safe acess of workers.

Supply of HSE personnel HOUSE-KEEPING SUPERVISOR over and above the requirement as specified in EIL Standard Specification No. 6-82-0001 at site as per the written instructions of Engineer-in-charge (the rates shall be inclusive of all other payments such as PF, ESI, other benefits payable to the workmen as per the prevalent labour laws).

GENERAL CIVIL

TANK PADS

Supplying, Transporting, Storing, Fabricating & Erecting in position and testing/ examining bolted and/ or welded Structural Steel Works at all locations and levels in HANGER SCAFFOLDING below piperack, comprising of hangar channels, fabricated pen wen ladder beams, steel planks bent to shape and size and any other sections, if required, all as per sketches/ specifications and load tested for statisfactory performance, including cutting to required size, straightening/ bending if required, edge preparation, cleaning, preheating, bolting/ welding of joints (including sealing the joints of box sections with continuous welding and plugging any open ends & holes of box sections), finishing edges by grinding, fixing in line and level with temporary staging & bracing and removal of the same after erection, including preparation and submission of detailed fabrication drawings, preparing the surface for painting as per BIS codes after fabrication etc. all complete as specified and directed. All items shall be removed & carried back by Contractor as per instructions of Engineer-in-Charge after completion of works. (Supply of All Material In Contractor's Scope).

Providing and fixing double scaffolding system of any height made with 40 mm dia MS tube 1.5 m centre to centre, horizontal & vertical tubes joining with MS tubes, MS tube challies, MS clamps and MS staircase system in the scaffolding for working platform/ staircase etc., and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc., wherever required for inspection of work at required locations with essential safety features for the workmen etc., all complete as per directions and approval of Engineer-in-charge. (Height shall be measured from Floor/ platform from where scaffolding is erected) including providing Aluminium ladders for safe acess of workers.

Providing and laying of PVC LINER of thickness 30 MIL conforming to IS:15909 below tank pad foundations or any other place at all heights & depths without any damage during subsequent activities including handling, transportation, unloading, storage, laying in position, jointing & overlapping as per manufacturer's recommendations, including supply and providing Asphalt impregnated fiberboards for anchoring, etc., all complete as per drawings, specifications and directions of Engineer-in-charge. (All materials including consumables shall be in contractor's scope of supply)

Providing and fixing double scaffolding system of any height made with 40 mm dia MS tube 1.5 m centre to centre, horizontal & vertical tubes joining with MS tubes, MS tube challies, MS clamps and MS staircase system in the scaffolding for working platform/ staircase etc., and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc., wherever required for inspection of work at required locations with essential safety features for the workmen etc., all complete as per directions and approval of Engineer-in-charge. (Height shall be measured from Floor/ platform from where scaffolding is erected) including providing Aluminium ladders for safe acess of workers.

SOR Sl. No.: 1637 || PART NO: 0 || SOR NO: B861-000-81-41-PK-SOR-3001-0-1M || ITEM NO: 01GC.10.7

Providing and fixing double scaffolding system of any height made with 40 mm dia MS tube 1.5 m centre to centre, horizontal & vertical tubes joining with MS tubes, MS tube challies, MS clamps and MS staircase system in the scaffolding for working platform/ staircase etc., and maintaining it in a serviceable condition for the required duration as approved and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc., wherever required for inspection of work at required locations with essential safety features for the workmen etc., all complete as per directions and approval of Engineer-in-charge. (Height shall be measured from Floor/ platform from where scaffolding is erected) including providing Aluminium ladders for safe acess of workers.

SOR Sl. No.: 1639 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC

SOR Sl. No.: 1640 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.5

SOR Sl. No.: 1641 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.5.MG15

SOR Sl. No.: 1642 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.6

ed from approved approved areas for all leads from Complex Limit including excavation of earth at approved areas, clearing and stripping at approved areas (if necessary) loading, unloading, transportation etc., clearing and stripping as per specifications, uprooting of vegetation, roots and disposal of the shrubs, bushes, roots etc., breaking clods, spreading in layers not exceeding 20 cm loose thickness, watering, ramming and compacting with road roller to give at least 97% of laboratory dry density with heavy compaction as per IS:2720 Part-VIII, providing testing apparatus and testing the degree of consolidation, dressing and leveling, etc. complete including disposal of all unserviceable materials if any within the boundary limit for all leads etc. as per drawings, specifications and directions of Engineer-in- Charge.

Supplying and Laying of Wet Mix Macadam (WMM) in BASE COURSE (Section 406 of MORTH Specification of Road & Bridge works) using tough, clean, sound & durable stone aggregates including premixing the material (mixing in Plug Mill/ Pan Type Mixer), including transportation to site, laying & spreading in layers not exceeding 125 mm compacted thickness & rolling with vibratory roller 80-100 KN static weight or equivalent capacity to proper grade, camber & level with all leads & lifts etc. complete as per drawing, specifications (MORTH, EIL) & directions of Engineer-in-Charge.

Supply of forged/ cast fittings

Supplying the following forged fittings and flanges, conforming to piping material specifications of tender documents and delivering the same to Owner's stores/workspot etc. all complete as per the directions of Engineer-in- Charge.

Elbow 90 Degree for following Nominal Sizes and Piping Material Class

Dia. 12 Inch Pipe Class A33A

Dia. 3 Inch Pipe Class A91A

Elbow 45 Degree for following Nominal Sizes and Piping Material Class

Dia. 6 Inch Pipe Class A33A

Dia. 8 Inch Pipe Class A33A

SOR Sl. No.: 1653 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.12.1.2.1V49

Eccentric Reducer for following Nom. Dia. 1 x Nom. Dia. 2 and Piping Material Class

Nom. Dia. 1 8 Inch Nom. Dia. 2 6 Inch Pipe Class A94A

Equal Tees for following Nominal Sizes and Piping Material Class

SOR Sl. No.: 1658 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.12.1.4.1V70

Flanges, complete with nuts, bolts, gasket etc., for following Nominal Sizes and Piping Material Class

SOR Sl. No.: 1661 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.12.1.6.1V54

SOR Sl. No.: 1662 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.12.1.9

MISC. CIVIL AND STRUCTURAL WORKS FOR U/G PIPING AND OTHER CIVIL WORKS

Providing and laying brick masonry with locally available bricks of specified class (Brick of class lower than specified shall not be accepted) in cement mortar 1:4 (1 cement : 4 Coarse sand) in one or more brick thickness and in any shape in foundation and plinth for valve pits, drains, circular/square maholes, wing walls, etc. including providing recesses, openings, etc. including curing, finishing the joints flush below ground level and raking out joints in plinth with all labour and material, etc. complete as per drawings, specifications and direction of Engineer-in-Charge. For following Brick Class.

All materials including cement supplied by the Contractor and Following Brick Class

Brick Class 5

Providing 13mm thick average cement plaster in cement mortar 1:3 (1 cement: 3 sand) on brick walls/stone masonry/pitching or on concrete surfaces for manholes, valves pits, culverts, wing walls, etc. including cleaning and preparation of the surface, scaffolding, curing etc. for all depths and heights complete as per drawings specifications and direction of Engineer-in-Charge.

All materials including cement supplied by the Contractor.

MISCELLANEOUS ITEMS

Supply and installation of combined safety shower and eyewash units as per spec. no.6-66-0038, including providing and fixing of necessary foundation bolts in foundations/ pavement etc. complete. Each safety shower shall have proper sign board with florescent letters showing their location, all complete as per specification, drawings and direction of Engineer-in-charge.

Supplying & Laying 60mm thick interlocking Paver Blocks for footpaths and any other place etc. including providing 40 mm thick sand filling below Paver Blocks including compaction of sand layer, filling the joints by dry sand, providing precast kerb stone of PCC M 30 at edges and at every 6.0m across the foot path, including preparation of compacted base/ sub base etc. all complete as per drawing, standard, specification and directions of Engineer-in-Charge. (All material including cement supplied by contractor, paver blocks shall confirm to category "A" as per IRC SP63. Colour and shape of paver block shall be as per Owner requirement.).

Modification Works

MODIFICATION AND EXTRA WORKS ( IF ANY ) Cuting,bevelling,fitup,welding of dif

SOR Sl. No.: 1674 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.27.1

SOR Sl. No.: 1675 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.27.1.1

SOR Sl. No.: 1676 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.27.1.3

SOR Sl. No.: 1677 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.27.1.4

SOR Sl. No.: 1678 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.27.2

SOR Sl. No.: 1679 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.27.2.1

SOR Sl. No.: 1680 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.28

SOR Sl. No.: 1681 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.28.3

SOR Sl. No.: 1682 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.28.3.1

SOR Sl. No.: 1683 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.28.3.1.1V1

SOR Sl. No.: 1684 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.28.3.1.1V2

SOR Sl. No.: 1685 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.28.3.1.1V3

SOR Sl. No.: 1686 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.28.3.1.1V4

SOR Sl. No.: 1687 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.28.3.1.1V5

SOR Sl. No.: 1688 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.29

Providing and laying brick masonry with locally available bricks of specified class (Brick of class lower than specified shall not be accepted) in cement mortar 1:4 (1 cement : 4 Coarse sand) in one or more brick thickness and in any shape in foundation and plinth for valve pits, drains, circular/square maholes, wing walls, etc. including providing recesses, openings, etc. including curing, finishing the joints flush below ground level and raking out joints in plinth with all labour and material, etc. complete as per drawings, specifications and direction of Engineer-in-Charge. For following Brick Class.

SOR Sl. No.: 1661 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.12.1.6.1V54

Flanges, complete with nuts, bolts, gasket etc., for following Nominal Sizes and Piping Material Class

SOR Sl. No.: 1662 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.12.1.9

MISC. CIVIL AND STRUCTURAL WORKS FOR U/G PIPING AND OTHER CIVIL WORKS

Removal of existing A/G piping of all thickness including cutting, unbolting of flanged joints / cutting of pipe lines wherever required, removing supports, all fittings, flanges etc., cutting of pipes in appropriate lengths for transporting purpose, transporting all material to owner's storage point within the complex as designated by Owner including stacking of material and disposing of waste etc. as instructed by Engineer - in - charge.

For C.S. A/G Pipe of following nominal dia.

Nominal Dia 8 Inch

Nominal Dia 4 Inch

Nominal Dia 6 Inch

Nominal Dia 12 Inch

Removal of existing U/G piping

For CS Piping dismantling, Thickness <=10 mm , For following Nominal Sizes

NB 2 inch - 6 inch

SOR Sl. No.: 1678 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.27.2

SOR Sl. No.: 1679 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.27.2.1

Portable/ trolley mounted Extinguishers

SOR Sl. No.: 1678 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.27.2

SOR Sl. No.: 1679 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.27.2.1

SOR Sl. No.: 1704 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.36.1

SOR Sl. No.: 1678 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.27.2

Supply and installation of portable CO2 extinguishers including transporting to worksite, fixing in position including all accessories and all labor and material etc. complete as per drawings, specification, data sheet and directions of Engineer-in-Charge.

Capacity in Kg 4.5

For CS Piping dismantling, Thickness <=10 mm , For following Nominal Sizes

NB 2 inch - 6 inch

SOR Sl. No.: 1678 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.27.2

SOR Sl. No.: 1709 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.38

SOR Sl. No.: 1710 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.38.1

SOR Sl. No.: 1678 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.27.2

SOR Sl. No.: 1709 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.38

SOR Sl. No.: 1713 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.38.1.1.1V3

SOR Sl. No.: 1715 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.38.1.1.1V5

Painting of uninsulated surfaces for ' Industrial marine ' environment as per painting specification for CS piping for design temp group: -14 to 80 (Deg C) including surface preparation. For following valve sizes

Dia. Of Valve 12 Inch

Dia. Of Valve 4 Inch

Dia. Of Valve 6 Inch

Dia. Of Valve 3 Inch

Dia. Of Valve 8 Inch

Fabrication and Erection of piping (underground)

Carbon Steel Piping (Non IBR), Thickness <=10 mm

Fabrication, For the following nominal sizes

SOR Sl. No.: 1727 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.40.1.1.1.2

Erection including corrosion protection coating, for Water System (Pressure Piping), For following Nominal Sizes

SOR Sl. No.: 1730 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.40.1.1.2.2

Erection including corrosion protection coating, for Waste Water Collection System (Gravity Flow), for following Nominal Sizes

SOR Sl. No.: 1727 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.40.1.1.1.2

Fabrication and Erection of piping (Above ground)

Erection including corrosion protection coating, for Water System (Pressure Piping), For following Nominal Sizes

ges of uneven/different thickness wherever required), fitup, bending, preheating wherever required, welding, threading, and laying of pipes of all type and thickness over pipe sleepers, overhead on racks and at all elevations, connecting with equipment nozzles, strainers, orifice assemblies, tapping for pressure gauges etc., fixing of gaskets, bolts, nuts including application of torque wherever required and all other inline instruments and fitting like elbows, reducers, tees, vents, drains, SW valves upto 1.5 NB, alignment, cleaning & flushing by water/compressed air, hydrostatic, pneumatic, vacuum, spark testing and any other type of testing as specified, draining, drying by compressed air completing all such works in all respects (including preparation of isometrics as mentioned in the scope of work for the job) as per drawings, specifications and instruction of Engineer-in-charge. (Pipes and fittings shall be supplied by owner as free issue material)

Erection including corrosion protection coating, for Water System (Pressure Piping), For following Nominal Sizes

SOR Sl. No.: 1737 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.42.1.1.1

NB 8 inch -14 inch

Erection , for Water System (Pressure Piping), For following Nominal Sizes

Erection including corrosion protection coating, for Water System (Pressure Piping), For following Nominal Sizes

SOR Sl. No.: 1742 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.42.1.1.2.3

SOR Sl. No.: 1743 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.44

SOR Sl. No.: 1744 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.44.1

SOR Sl. No.: 1745 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.44.1.1V23

SOR Sl. No.: 1746 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.44.1.1V24

SOR Sl. No.: 1747 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.44.1.1V66

SOR Sl. No.: 1748 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.44.1.1V67

SOR Sl. No.: 1749 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.44.1.1V94

SOR Sl. No.: 1750 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.45

SOR Sl. No.: 1751 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.45.1

SOR Sl. No.: 1752 || PART NO: 0 || SOR NO: B861-000-81-45-PK-SOR-3001-0-1M || ITEM NO: 01GC.45.1.1