IMPROVEMENT TO SEWAGE SYSTEM INCLUDING STP AND INFRASTURCTURE FOR UTILISATION OF TREATED WATER AT AF STN BELAGAVI

Amount

Design, supply, construction, installation , testing and commissioning of 21 M3/H for 12 hrs working ultrafiltration (UF) plant for recycling of STP treated water consisting of the following components complete all specified and as directed by Engr-in- Charge. Any left out items for smooth and efficient functioning of the plant includes in the quoted rate ..

(a) UF feed pumps - 02 Nos (b) Micron cartridge Filter ( Basket Filter) of capacity 100 Micron with housing & Catrige - 01 Nos (c) Chlorine dosing ( For CEB) NaOCl with dozing tank capacity 500 Ltrs - 01 Nos and dozing pump electronic type of capacity 40 LPH - 02Nos ( 1W+ 1S/By) (d) Caustic Dosing (for CEB)- NaOH dosing tank cap 500 Ltr - 01 Nos and dosing pump of cap 42 LPH electronic type - 02 Nos ( 1W + 1 S/by) (e) HCL Dosing system having Dosing tanl of cap 500 Ltrs - 01 No and Dosing pump of cap 100 LPH electronic type - 02 Nos ( 1W + 1 S/by)

(f) LDPE Recovery clean tank (RC Tank) of Cap 2000 Ltrs - 01 No. (g) RC pump of cap 26Cum/hr, 25 Mtr head centrifugal type material of Cosnstruction- CI -02 Nos (1 W + 1 S/by). (h) UF module having area 59 sqm, SKID- MSEP, Average percentage of recovery - 96% or above (j) GRP/FRP UF permeat water tank Width - 5m , Length - 5 m, Max water level - 3m (k) Instruments ( Rota flow meter - 02 Nos, Pressure transmitter - 02 Nos , PLC SCADA system - 01 No, Level switches - 02 Nos , Rotameter - 01 No) (l) Incl PVC/CI valves & UPVC / CPVC Pipings of suitable pressure ratings (m) LT Control Panel for controlling UF Plant incl all connected MCCB and accessories.

Air Scouring : Air Scouring will be made available from existing STP blowers as directed by GE and quoted rate against item No 1 above is deemed to be inclusive of this provision.

Supply, install, testing and commissioning of Centrifugal pump sets of capacity 10 HP(7.5KW), three phase, 415 Volt suitable for 80x65mm dia pipe for suction and delivery head range 34Mtr, discharge14.6 LPS including provision of suitable PCC foundation for fixing of Pump Sets and provision PVC copper Cables 3 X 6sqmm incl PVC Condutis 25mm from starter to Motor complete all as specified and directed. Make: Crompton/Kirloskar. Note: 1. Standard test certificate for pump and motor has to be submitted by the contractor cost for the same is deemed to be included in the quoted rate. 2. Test results like routine test/Pump performance test/Motor performance/material of construction etc shall be submitted by the contactor after installing the pump sets cost for the same is deemed to be included in the quoted rate.

Suppy, Install, testing and commissioning Non Clog type Horizontal submersible pumps with chrome steel impeller and cutter, non-clog to pass 25 mm size particles suitable Head 33 mtr and discharge 810 LPM 10 HP Note: 1. Standard test certificate for pump and motor has to be submitted by the contractor cost for the same is deemed to be included in the quoted rate. 2. Test results like routine test/Pump performance test/Motor performance/material of construction etc shall be submitted by the contactor after installing the pump sets cost for the same is deemed to be included in the quoted rate.

Supply and fixing testing and commissioning Chain Pulley Block 2Ton Single fall CPB with chain 8mm thick including fixing arrangements complete all as specified and directed. Make: Ferriterro India Pvt Ltd. Model No : LL020

M&L angle, channels or tee sections, fixed independently, without connection plate, etc for (Fe 410 grade ) including necessary drilled holes, welded together all as directed.

M&L for earthing with galvanized steel earth plate electrode of size 600 mm x 600 mm x 6.0 mm buried directly in ground (earth pit not less than 2.25 Mtr below normal ground level ) connected to galvanized earth lead strip of size 32 mm x 6 mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel including 40 mm dia light grade GI tubing for protection of earth lead, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm dia, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type C1, 50 mm thick precast RCC (1:2:4) type B1 pit cover reinforced with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar including galvanised strip of size 32 mm x 6 mm for extension of earth lead and necessary excavation, earth work, in soft/loose soil and disposal of soils to a distance not exec 50 mtr and necessary connection and testing complete all as shown in electrical plate No. 3 of SSR Pt-I, 2009 and all as directed and specified.

Supply and Lay High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 in trenches/floor incl all fittings of bore 25 (outer dia 32mm)

Supply and Lay High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 in trenches/ floor/Wall incl all fittings of bore 40 (outer dia 50mm)

Supply and Lay High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 in trenches incl all fittings of bore 50 (outer dia 63dia)

Supply and Lay High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 in trenches incl all fittings of bore 80 (outer dia 90mm)

Supply and Lay High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 in trenches incl all fittings of bore 100( outer dia 110mm).

Supply and Lay High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 in trenches incl all fittings of bore 150 (outerdia 160mm).

Supply, fixing, testing and commissioning cast iron sluice valve PN-1.6 with both ends flanged confirming to the IS-14846 with brass spindle and iron wheel head with both ends flanged including new rubber gasket, bolts and nuts etc complete all as specified and directed for the following sizes:-

80mm bore

100 mm bore.

150 mm bore.

Supplying,fixing,commissioning and testing of valve reflex or Non Return Valve(NRV) for 150mm dia (6”) with by pass arrangement GI with all necessary connection all as specified and directed at site by Engr-in-Charge..

Supply and fix foot valve confirming to IS-4038 of size 80mm dia all as specified.

Supply and fix valve, globe or gate confirming to IS- 9338 suitable for 50 mm (2") dia pipe all as specified.

Supply and fix valve, globe or gate confirming to IS- 9338 suitable for 40 mm dia pipe all as specified.

Supply and fix valve, globe or gate confirming to IS- 9338 suitable for 25 mm dia pipe all as specified.

M&L for Construction of brick massonry valve pit chamber of inner dimension 100x100x100 cms suitable for sluice valves upto 150mm size, with PCC 1:4:8 type D-2 for foundation, brick work in cm 1:6 rendering 1:4, 15mm plastering, coping in PCC 1:2:4 type B-1, incl necessary earth work, including MS sheet cover of thickness 3.15mm on 50x50x6.0 mm angle iron framework including two coats of synthetic enamelled paint over a coat of red oxide primer with making provision of locking arrangement complete all as specified and directed.

M&L for Construction of brick massonry valve pit chamber of inner dimension 90x90x90 cms suitable for sluice valves upto 100/80mm size, with PCC 1:4:8 type D-2 for foundation, brick work in cm 1:6 rendering 1:4, 15mm plastering, coping in PCC 1:2:4 type B-1, incl necessary earth work, including MS sheet cover of thickness 3.15mm on 50x50x6.0 mm angle iron framework including two coats of synthetic enamelled paint over a coat of red oxide primer with making provision of locking arrangement complete all as specified and directed.

M&L for Construction of brick massonry valve pit chamber of inner dimension 60x60x60 cms suitable for sluice valves upto 50mm size, with PCC 1:4:8 type D-2 for foundation, brick work in cm 1:6 rendering 1:4, 15mm plastering, coping in PCC 1:2:4 type B-1, incl necessary earth work, including MS sheet cover of thickness 3.15mm on 50x50x6.0 mm angle iron framework including two coats of synthetic enamelled paint over a coat of red oxide primer with making provision of locking arrangement complete all as specified and directed.

Cutting HDPE main pipes of dia upto 80 mm and reducing to required length in position for insertion of new Tee, branches etc

Cutting HDPE main pipes of dia upto 150 mm and reducing to required length in position for insertion of new Tee, branches etc

Cutting HDPE main pipes of dia upto 100 mm and reducing to required length in position for insertion of new Tee, branches etc

Supply , install, testing and commissioning of LT Feeder pillar Box AC 415 V , 50 HZ 3 Phase 4 wire of suitable size to accomodating the following accessories totally enclosed self supporting structure / cubicle , fully compartmentalized type , weather proof , vermin proof indoor type made out of 3.15 mm thick MS sheet protection IP 54 , suitable for outdoor use , with bottom cable entry with suitable cable glands structure with angle iron frame work with four legs grouted to PCC (1:2:4) type B1 , foundation block with suitable mounting arrangement for bus bars voltmeter, ammeter and MCCBs, double hinged doors at front with suitable locking arrangement , Provision of louvers at sides , structure treated under 8 - tank metal treatment process and duly powder coated with 200A electrical grade copper bus bar (30x5mm)for phases and neutral complete with suitable digital type meters resin cast CTs, CPRI type tested, internal wiring all prewired including the following incoming and outgoing complete all as specified and directed :-

MCCB FP 80 Amps rating, 25 KA breaking capacity - 01 No. (Incoming)

MCCB FP 32 Amps rating, 16 KA breaking capacity - 02 No. (Out going)

MCCB TP 25 Amps rating, 16 KA - 4 (4 outgoing )

MCB SPN 6-32 Amps - 01 Nos

Indicator lamp LED type - 3Nos

Digital type amperemeters resin cast CTs of 32/5 A- 02 Nos

Digital type amperemeters resin cast CTs of 80/5 A- 01 Nos

Fully Automatic Star Delta Starter Suitable for 10HP Motor 9-13A Make: havells Cat Part No: IHPASDMB -04 Nos

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth including for laying pipes,cables, poles etc and getting out hard/dense soil

Excavating in trenches, exc 1.5 m in depth and n exc 3 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m depth and including for laying pipes,cables, poles etc and getting out hard/dense soil.

Excavating in post holes(or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard / dense soil

Surface excavation n. exc. 30 cm deep averaging 15 cm deep and getting out in hard/dense soil.

Returning and filling in soil including spreading leveling watering and well ramming in layers not exceeding 25cm all as specified.

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point.

Removing excavated soil to a distance exceeding to a distance 2500 m and not exc 5000 m and depositing where directed and depositing where directed at a level not exceeding 1.5m above the starting point.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 25 X 4 mm galvanised iron strip

Cutting the existing PCC/bituminous road of any description to a size not exc. 0.5m wide x 0.6m deep for crossing of pipe including refilling, ramming and making top 150 mm thick surface good with plain cement concrete 1:3:6 type C1 using 20 mm graded stone aggregate complete all as specified and directed.

S&F MS pipe of dia 150mm 6mm thick incl specials for pumpset connection

S&F MS pipe of dia 80mm 6mm thick incl specials for pumpset connection

M&L for providing plain cement cement concrete 1:3:6 Type C-2 using 40mm graded stone aggregate as in foundations filling mass concrete complete all as specified and directed.

M&L for providing plain cement cement concrete 1:4:8 Type D-2 using 40mm graded stone aggregate as in foundations filling mass concrete complete all as specified and directed.

M&L applying anticorrision synthetic enamel paint over a coat of red oxide primer on new steel surfaces over 10 cm in width or girth including preparation complete all as specified and directed.

M & L hard core of broken stone gauge n. exc. 63 mm deposited and spread and levelled in layers n. exc. 15 cm thick watered and rammed to a true surface.

S & F TMT steel bars 10 mm dia and over, cut to length, bent to shape required including cranking bending, hooking ,spirally for hoping for a columns for ends and binding with mild steel wire annealed not less than 0.9 mm dia all as specified and directed.

S & F TMT steel bars 8 mm dia and over, cut to length, bent to shape required including cranking bending, hooking ,spirally for hoping for a columns for ends and binding with mild steel wire annealed not less than 0.9 mm dia all as specified and directed.

M&L Reinforced cement concrete nominal mix type B1 (1:2:4) 20 mm graded aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

M & L RCC type B1 1:2:4 (20mm aggregate) nominal mix in columns ,pillars,piers,posts and struts as specified

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter with fair finished flat surfaces

Form work to sides of columns, pillars etc with fair finished square,rectangular,or polygonal surfaces of concrete all as specified and directed

S&F Joist, channel, angle, or tee sections,fixed independently, without connecting plates, etc all for water staging /cleats etc (cut to ordinary lengths i.e. within 20mm of the length indicated) of Fe 290 (Gde E-165)

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk)forming holes, without any attachment of Fe-410 W (Gde E-250 )Quality B

S&F Mild stell rag or lewis bolts with Dia of neck 20mm, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, exc 30cm long all as specified and directed

Material and labour preparation of new steel surface of any description, not otherwise described over 10 CM width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as sped and directed by EIC

Rotational moulded polyethylene water storage tanks of capacity 1000 litres (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part Water tanks, open or closed,hoisted and fixed in position

Rotational moulded polyethylene water storage tanks of capacity 2000 litres (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part Water tanks, open or closed,hoisted and fixed in position

S & F PVC Lid Cover for over head water tank including locking arrangement like hinges,split pin etc for 1000/ 2000 litres capacity tanks complete all as specified and directed.

S & F Ball valves 25mm bore with minimum weight of 455 gram, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified and directed.

S & F Ball valves 40mm bore with minimum weight of 690 gram, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified and directed.

Taking up/down steel tubing and connection, including cleaning for refixing if required for the following sizes :-

15 mm bore.

20 mm bore

25 mm bore

50 mm bore

80 mm bore

Cutting holes of superficial area not exceeding 150 Sq cm into or through in in brick walls built, in cement mortar or cement lime mortar and stone walls built in lime mortar or walls of lime concrete.and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required

Demolition of Precast concrete block walling or precast concrete articles built in cement mortar.

M & L Pre cast cement concrete block masonry with solid blocks,exc 10 cm in width and setting in mortar, complete type C1, 1:3:6 (20 mm graded crushed aggregate ) set in CM (1:4).

Taking down cement plaster on brick or stone wall etc any description, including raking out joints, hacking for key, scrubbing down with water etc.

M & L Rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete surfaces finished fair and even and smooth with out using extra cement.

Three coats of white wash on walls, pillasters, cornices, etc., on newly plastered walls including preparation of surfaces all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M & L Glazed coloured ceramic tiles in vertical surface 300 x 200 x 7 mm thick set and jointed in neat cement slurry and pointed in white cement mixed with matching pigment, over and including 10 mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces.

M & L Glazed coloured ceramic tiles in vertical surface 450 x300 x 7 mm thick set and jointed in neat cement slurry and pointed in white cement mixed with matching pigment, over and including 10 mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces.

M & L Non-skid coloured Ceramic tilse 7 to 8 mm thick (Square or rectangular) area of each tile exc 0.06 Sq m but not exc 0.11 Sq m, in floors etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the existing, over & including 15 mm thick screed bed in CM 1:6 all as directed.

M & L 25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate), as in sub floors.

PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in foundation, filling and mass concrete all as specified and directed

S & F 80 mm bore GI tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors and making good the distrubed surface to match the existing.all as directed.

Fixing only in repairs of old tubing obtained from item No. 19 above including connections in new or old position on walls , ceiling, floors etc all as directed of following bores.:-

15 mm bore.

20 mm bore

25 mm bore

50 mm bore

80 mm bore

S&F Tubes, 'mediam grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors

15 mm bore.

20 mm bore.

25 mm bore

S & F Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors including fittings like elbow,tee,reducer etc., any typeof pipe as specified of following bores.:-

15 mm bore.

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth in brick walls

Screwing existing steel tubing(15 mm) for alterations or additions (or lengthening screw on pipe to form connector) without taking down

Screwing existing steel tubing(25 mm or 32 mm) for alterations or additions (or lengthening screw on pipe to form connector) without taking down

Screwing existing steel tubing(40 or 50 mm) for alterations or additions (or lengthening screw on pipe to form connector) without taking down

S & F in repairs angle stop valves of PTMT 15 mm dia any colour high pressure screwed for iron pipe and fixed. (min wt 90 gms).

S & F in 15 mm CP angle/Stop valves in repairs fancy type cast copper alloy screwed down, high pressure, with crutch handle, screwed both ends and fixed all as directed.

S & F in 15 mm CP angle/ Stop valves in repairs fancy type cast copper alloy with long shank and cup(Concealed screwed down, high pressure, with crutch handle, screwed both ends and fixed all as directed.

S & F in repairs 25 mm bore Gun metal gate valves, with iron wheel head, screwed both ends for iron pipe and fixed etc all a spechied andas directed.

S & F in 40 mm bore Gun metal gate valves, with iron wheel head, screwed both ends for iron pipe and fixed etc all a spechied andas directed.

S&F in non return alve of 15mm brass body all as specified and directed

S&F in non return alve of 20 mm brass body all as specified and directed

S&F in non return alve of 25 mm brass body all as specified and directed

S&F in non return valve of 40mm, brass body all as specified and directed.

S & F in 125 mm dia with waste hole of PTMT grating doom, min Wt 40 gms..

S & F in PVC valveless, symphonic action type, flushing cistern, low level 10 Ltr capacity white with inlet, ball valve, float and handle including brackets, PVC flush pipe 32 mm dia or bore as required all as specified and directed.

Fixing only in repairs flushing cistern including all necessary repair work, parts of flushing kit, plastic flush washer, flush handle/lever and connections to pipes etc all as directed.

S & F in repairs PVC connection 15 mm dia with PTMT nut of length 450 mm.

S & F in repairs PVC connection 15 mm dia with PTMT nut of length 600 mm.

M & L roof trusses (Framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc of Fe 410 w(Gde E-250) qualty A

M & L steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St 240

M & L pre painted glavalume alumium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Supply and spreading 50 mm Sand cushion bed as below the inter loking pavered blocks

M/L PCC 1:2:4 type B-2 using 40 mm graded stone aggregate as in flooring with 75mm thickness

M & L Precast Cement concrete solid building blocks or slabs 10 cm thick and setting in cement mortar 1:4., complete type C1, 1:3:6 (using 20 mm graded aggregate).

M & L Rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces finished fair and even and smooth with out using extra cement.

M & L Machine pressed 60 mm thick precast concrete interlocking paver blocks, M-35 grade any shape & size confirming to IS-15658-2006 with grey cement and pigment etc all as specified and directed.

S & F Mild steel work as in angle or other steel section posts and struts in fencing and gates including cutting tops to shape as directed, drilling holes, notching for wire, etc; flat iron fillets strips to securing mesh, line wires, straining bolts with one nut and washers etc including all necessary welding, drilling, bolting etc and similar work confirming to Fe-290 Gde E-165.

Mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other, or screwed both end , each screwed end to be fitted with washers and one hexanonal or square nut,but length of bolt not exc 5cm long. Diameter of shank will be 5 to 10 mm.

S & F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering. Door/Gates etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings fastenings and fixing complete, Fe 410 W(Gde-E-250) quality-B.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire.

Supplying only Chain Link MS galvanised fencing any size or type.

M & L two coats of anti corrosion synthetic enamel paint over a coat of red oxide primer on steel surfaces over 10 cm width or girth including preparation, etc all as specified and directed.

M & L two coats of anti corrosion synthetic enamel paint over a coat of red oxide primer on steel surfaces not exc. 10 cm in width or girth including preparation, etc all as specified and directed.

M & L two coats Cement based paint over a coat of cement wash primer etc on new walls including preparation, etc all as directed.

Supply & Laying sub class `B’ burnt bricks old size over the HT/LT cable having compressive strength not less than 50 Kg/Cm2, laid in trenches with width equal to width of the brick laid flat for protection of cable complete all as specified and directed.

Supply and fix Galvanised steel tubing, light grade, with fittings and MS clamps, nuts, bolts etc of 50 mm dia bore for cable protection on pole, road crossing or ground in pillars for fixing gate light etc complete all as specified.

Supply laying and testing cable XLPE Insulated screened PVC bedded,galvanised steel strip or wire armoured,electric power cables(heavy duty) with stranded aluminium conductor, 1100 volts grade of size 3.5 core 35 sq mm

Supply laying and testing cable XLPE Insulated screened PVC bedded,galvanised steel strip or wire armoured,electric power cables(heavy duty) with stranded aluminium conductor, 1100 volts grade of size 2 core 10 sq mm

Supply laying and testing cable XLPE Insulated screened PVC bedded,galvanised steel strip or wire armoured,electric power cables(heavy duty) with stranded aluminium conductor, 1100 volts grade of size 2 core 6 sq mm

S&F LT cable path indicators of oval shaped size 200mmX150mmX6mm thick made of or moulded cast iron and emborsing LT UG cable and fixed on MS angle iron 25x25x5mm thick 40 cm in length with two nos nut, bolts and washers, including two coats of synthetic enamelled paint over a coat of zinc coat primer on exposed surface, angle iron to be fixed in to the ground including suitable PCC work, while returning and filling the excavated soil complete all as specified and as directed.

Supply and fix steel tubular swaged poles type 410 SP-31 (9 meter long) complete with CI base plate and two coats of Aluminium paint over a coat of red oxide primer after initial preparation of surfaces and finial complete all as specified and directed.

S & F Energy efficient & Long life Security Light Luminaire, of 70W not less than 7000 Lumens output, 5700 K with Pressure Die Cast Aluminium Housing, IP66 protection, heat resistant glass cover, high power LEDs as light source, electronic driver complete all as specified and as directed. Note: Light fitting shall be of PF>0.95 Make: Havells Cat Part No ENDURACITYLINERNEOSL70WLED757PASYBOTG

Supply and fix loop in loop out box 250x250x104 with connector of suitable way and 01 No of MCB SP 6-32Amps including necessary fixing arrangements with clamps fabricated out of flat Iron 20x3mm including nuts, bolts and washers on poles complete all as specified and as directed.

Cutting the existing PCC/bituminous road of any description to a size not exc. 0.5m wide x 0.6m deep for crossing of pipe including refilling, ramming and making top 100mm thick surface good with plain cement concrete 1:3:6 type C1 using 20mm graded stone aggregate complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as coping around poles etc complete including necessary form work and finishing the exposed surface even and smooth without using extra cement all as specified directed.

K. VENKATESH NAIDU

RYSA INFRATECH PRIVATE LIMITED