SPL REPAIRS TO BLDG NO T-116 AT CMDC AND SPL REPAIR BLDG NO T-70 AND ADDN / ALTN OF OTHER BLDGS AT VARIOUS LOACATIONS OF LUCKNOW CANTT UNDER GE EM LUCKNOW

Amount

Demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and pre cast concrete articles complete all as specified and directed by Engineer-in-Charge

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge

Demolition of cement concrete (un-reinforced) in ground floors and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge

M&L for 40mm thick PCC type B-1 1:2:4 ( 20mm graded agg) finished even and smooth with using extra cement all as specified and as directed.

M&L 75 mm thick cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as plinth protection/path and the like complete all as specified and directed by Engineer-in-Charge

M&L for filling joints between two panels with mix of 85/25 bitumen and sand in 1:3 complete all as specified and directed by Engineer-in-Charge

M&L for providing cement concrete type B-1, 1:2:4 (20 mm graded aggregate ) as in roof kerbs /padding or similar work or mud stops rounded or chamferred on edges complete all as specified and directed.

M&L for cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in coping, padding and bed block, wall through and the like including weathering slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

Taking down cement plaster on brick wall, racking out joints hacking for key scrubbing down with water complete all as specified and directed by Engineer-in-Charge

M&L for rendering 10 mm thick on brick work/ concrete surfaces in cement mortar 1:6 on fair faces finished fair & even complete all as specified and directed by Engineer-in-Charge

M&L for 15 mm thick rendering in CM 1:4 on fair faces of brick work surface finished even and fair without using extra cement complete all as specified and directed by Engineer-in-Charge (Note : Integral WPC shall be measured and paid seprately )

Supply only integral WPC of approved quality complete all as specified and directed by Engineer-in-Charge

M & l for preparation of newly plastered surfaces and applying two coat of oil bound distemper over one coat of oil base primer all as specified on walls surface including a thin layer wall care putty complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surafce of walls and applying two coats exterior emulsion weather coat paint over one coat primer including a thin layer wall care putty complete all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (But not backing) removing serviceable tiles to store and rubbish off the premishes complete all as specified and directed by Engineer-in-Charge

M&L for non skid ceramic tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.16 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 15mm thick screed in CM 1:6 complete all as specified and directed by Engineer-in-Charge

M&L for glazed ceramic tiles in vertical surfaces 350 x 250 x 7 mm / 450 x 350 x 7 mm [thick] set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 10mm thick screed in CM 1:3 complete all as specified and directed by Engineer-in-Charge

M&L 18-20mm thick machine cut Kota stone slab flooring with marble stone strips/ slab/ tiles as per design approved, over and including cement screed bed 15mm thick in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete all as specified and directed by Engineer-in-Charge

M&L 18-20mm thick machine cut Kota stone slab as in skirting /riser over rendering 10mm thick in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantlings 40 Sqcm and over in section, in any position as in framed works complete all as specified.

M&L for second class soft-wood clean swan in scantlings timber fixed complete all as specified and directed.

Dismantling of roof sheet (any descriptions) including ridges in roof covering all as specified and directed.

S&F for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof overing/cladding to wall, fixed with self tapping screws as specified.

S&F for Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof overing/cladding to wall, fixed with self tapping screws as specified.

Dismantling of wall and ceiling boards (fiber, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

M&L for PVC Wall panelling/Lining solid consisting of 5mm thick Plain/wood colour PVC sheet as approved inclusive of solvent cement and fixing at site on PVC frame including complete fixing arrangments on wall complete all as per manufactures specifications and complete all as specified and directed.

S&F for providing and fixing of E-board 600x600x4mm thick white prelaminated seif embosed reinforced designer ceiling board tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24 mm wide T-section/Angle section complete all as specified.

Taking down chowkhats or frame (wooden/aluminium) n. exc. 1.5 Sqm each with shutters (with out taking off shutters from the frame) and taken as credit all as specified and directed.

Taking down chowkhats or frames (wooden/aluminium) with shutters without taking off shutter from the frames exc. 1.5 but n. exc 4 sqm each all as specified and directed.

Taking down shutters of any description not exc 1 Sqm each complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description exc 1 Sqm but n.exc 2 Sqm each complete all as specified and directed by Engineer-in-Charge

S&F well seasoned 2nd class hard wood plan, solid, straight chowkat and frames, wrought framed, rebate on the solid rounded or chamfered, put together with glue pinned at joint complete all as specified and directed by Engineer-in-Charge

S&F for Mild steel work Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 as in small articles like angle iron framing work for manhole, rungs/steps in man hole all as specified.

M&L for plain cement concrete 1:3:6, type C-1 (using 20 mm graded stone aggregate) for embedding holdfast, bed block, cills, etc including necessary formwork complete all as specified and directed by Engineer-in-Charge

M&L for preparing surfaces of wood and woodbased marterial, steel and iron works new or old of any description and girth treating ends of post back of chowkats etc, area tarred exc 0.1 sqm but n exc 0.5 sqm each with tar or coal tar black paint complete all as specified and directed by Engineer-in-Charge

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified.

S&F 30 mm thick second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc , divided in to square with plain chamferef or rounded mitred and rebate sash bars, any numbers edges of framing plain, chamfered or rounded, size / section of members of shutters shall be as specified in SSR Part I section 8 clause 8.24 (a) complete all as specified and directed by Engineer-in-Charge

S&F 30 mm thick second class hardwood glazed shutters as in windows/vertilators open rebateed and prepared to received mitred aand secured sash bars any numbers edges of fsdraming plain chamfered of rounded in SSR Part I Section 8 caluse 8.24 (b).complete all as specified and directed by Engineer-in-Charge

M&L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise desceribed over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F aluminium sections ( conforming to IS) door with frame/chaukats of size 100mm x 44.45mm wide fabricated with 2mm thick section , double/single leaf shutter with 44.45mm wide fabricated with 2mm thick section having vertical and top rail 83.50mm, bottom rail and middle rail 115mm and including necessary jointing cleats, screws, neosprene rubber beading, PVC packing, incl 4.8 mm thick tinted glass panes/3mm thick aluminium composite panel, 100mm butt hinges (3 Nos in each panel), 150mm tower bolt (1 in each panel), locking arrangements with 100 mortice lock complete all as specified and directed.

S&F Anodised Aluminium alloy sections sliding windows shutters with frames/chaukats of size 100mm x 44.45mm wide fabricated with 2mm thick section, with 3 track sliding shutters over 3 track sliding section all around, comprising Series -C (20mm) duly fitted with neoprene beading, glazing clips,locking device, incl 4.8 mm thick tinted glass panes/3mm thick aluminium composite panel in 2 shutters and 0.46mm dia SS wiremesh in one shutter complete all as specified and directed. (Note :- Thickness of aluminium section minimum 2mm).

S&F Anodised Aluminium alloy sections in ventilators shutters with suitable size of frames/chaukats fabricated with 2mm thick section, with 02 shutters one is fixed and another is openable duly fitted with neoprene beading, glazing clips, locking device, incl 3mm thick tinted glass panes/3mm thick aluminium composite panel in 2 shutters complete all as specified and directed. (Note :- Thickness of aluminium section minimum 2mm).

S&F in repairs aluminium anodized grill weight of 3.13 Kg per Sqm (min) with suitable aluminium anodized frame of F/H section of 0.297 Kg per Meter (min) with suitable fixing screws/attachment etc complete all as specified and directed.

S&F for PVC door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with MS square tube, suppling & fixing in opening as per specn & drg complete all as specified and directed.

S&F for factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm with stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified.

S&F 75 mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge

S&F 100 mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge

S&F 100 mm size Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-Charge

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge

S&F Aluminium anodised sliding door bolt 300m long, with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, 300 mm long, mild steel, rat tail rod pattern springs including roller and roller plates complete all as specified and directed by Engineer-in-Charge

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed.

Hacking out old broken glass (any thickness size, quality or description) from wooden frames or stone, concrete or bricks round, glazed with putty or fixed with bedds complete all as specified and directed by Engineer-in-Charge

S&F 3 mm thick sheet glass, ordinary quality and glzing with oil putty/timber bedds in square in each pane complete all as specified and directed.

S&F for 4.8 mm thick sheet glass odinary qulity and glazing with oil putty/timber bedds in square in each pane complete all as specified and directed.

S&F for 3.0 mm thick figured glass ordinary quality and glazing with oil putty in each pane complete all as specified and directed.

S&F in repair curtain/harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc, complete all as specified and directed.

Taking up or down steel tubing and connections of 15 mm bore complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 20 mm bore complete all as specified and directed.

M&L 15 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

M&L 20 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Refixing old steel tubing and connections in new or old position ( walls, ceiling , floors, etc.)15 mm nominal bore complete all as specified and directed.

Refixing old steel tubing and connections in new or old position ( walls, ceiling , floors, etc.)20 mm nominal bore complete all as specified and directed.

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth on stone walls complete all as specified and directed.

Dismantling water tank capacity exc 250 & n.exc 500 ltr and taken as credit

M&L for Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt I. capacity of tank 500 litres complete all as specified and directed.

M&L for Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt I. capacity of tank 1000 litres complete all as specified and directed.

S&F in repair ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball , suitable for 20 mm bore pipe, screwed for iron pipe and fixed. .(Minimum weight 20mm-210gms) complete all as specified.

S&F in repairs Chromium plated fancy long body Bib taps with cup, cast copper alloy with crutch handle, screwed for 15 mm bore dia. iron pipe or for brass ferrule and fixed complete all as specified.

S&F in repair CP Angle stop cock ( one way) long thread with wall flange , fancy type screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified.

S&F in repairs Pillar taps, fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs CP mild steel gratings suitable for 75/100 mm dia NT/ FT complete all as specified.

S&F in repair vitreous China wash down water closet pan (padestal pattern Water Closet ) , ( excluding fixing bolts, flushing cistern and flush pipe) , including connection to drain ( or outgoing pipe) and to flushing pipe etc., complete all as specified and directed.

S&F in repairs Low level flushing cistern, moulded from virgin poly propylene complete all as specified and directed.

S&F in repairs Plastic water closet seat, white, closed pattern with flat bottom , and cover and mild steel chromium plated or aluminised hinging device complete all as specified.

S&F in repairs PTMT connections 15 mm size with PTMT nuts of length 450 mm complete all as specified.

S&F in repair vitreous china wash basin (WHB) , white , flat back , size 550mmx400mm including brackets, waste fittings , brass Chromium plated for glazed basins etc. embedded in red lead cement, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified.

S&F for vitreous china standard pedestal white WHB including waste fittings, brass, chromium plated for glazed ware basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed (32 mm bore) complete all as specified and directed.

S&F 32mm bore flexible pipe of PVC fixed to WHB/ urinals as waste pipe ( not less than 600mm) including PVC coupling complete all as specified.

S&F in repair cast iron floor trap with chromium plated grating including jointing to waste pipe wih cement mortar (75 mm bore of pipe) complete all as specified and directed.

Taking down pipes (any sizes) incl all fittings complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, or fixed to wall complete all as specified.

S&F 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, or fixed to wall complete all as specified.

M & L for preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge

M&L for applying one coats of Apex / Weather coat over old painted surface including preparation of wall surface complete all as specified and directed by Engineer-in-Charge.

M&L for Providing and applying minimum 1mm thick wall care putty over prepared surface to achive the surface even and smooth for painting complete all as specified and directed. (Rate included for necessary scafolding and arrangement for working up to 15 mtrs height).

M&L for preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of distemper oil emulsion of any tint/shade complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge

M&L for preparation of old painted surfaces of steel of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge

M&L for vitrified ceramic tiles 10 mm thick (square /rectangular ) polished dark shade, area of each tiles not exceeding 0.36 sqm, in floor etc. set and jointed in neet cement slurry and pointed white or coloured cement to match the shade of the tiles, laid over and including 20 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for 18 to 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete over and including 20 mm thick screed bed or bedding layer in CM 1:6 finished even and rough all as specified and directed.

M&L for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed all as specified and directed.

S&F for powder coated aluminium extruded sections (conforming to IS) (minimum thickness of powder coating 50 micron) three track sliding window shutter with frames comprising series-C (20mm) , duly fitted with neoprene beading, glazing clipss, locking devices, heat absorbing glass 4.8mm thickness (in 2 shutters) and with SS wire cloth of 0.46mm nominal dia of wire and average width of aperature 1.4mm (in one shutter) complete all as specified and directed.

M&L for distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work over wall/ceiling surfaces

M&L for distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on old work over wall/ceiling surfaces including complete removal of existing treatment on walls complete all as specified.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for 19 mm thick block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work including exposed surfaces finished with external teak wood lipping, 6 mm thick fixed with nails complete all as specified and directed.

M&L for 19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including exposed surfaces finished with external teak wood lipping, 6 mm thick fixed with nails complete all as specified and directed.

S&F 50 mm size butt hinges, medium weight , cold rolled, mild steel and fixed complete all as specified and directed

S&F of continuous (piano) hinges mild steel bright finish or electro galvanised 30 mm width of flaps complete all as specified and directed.

S&F of 75 mm brass handle, cast type, polished bright all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M&L for RCC M-25 (Nominal mix) using 20 mm graded stone aggregate as in roof slab, shelves, balcony etc complete all as specified

M&L for formwork to soffits of suspended slabs, such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick [Horizontal or sloping] for rough finished faces complete

S&F of TMT bars 10 mm dia and over, cut to length , bent to shape required , including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

S&F of TMT bars 6 mm to 8 mm dia, cut to length , bent to shape required , including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mmall as specified and directed.

S&F of 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F for CP angle cock (two way) complete all as specified.

S&F for health faucet, chromium plated rising spray with wall brackets with 1.5m long metallic flexible tube with 15 mm dia fixed in repair complete all as specified and as directed.

S&F white Toilet paper holder of stainless steel (specified make) fixed to walls with chromium plated (CP) brass screws complete all as specified.

S & F PVC connection 15mm size with PTMT nut of length 450mm

S & F chromium plated soap tray fixed with rawl plugs complete all as specified and directed.

S&F in repair for Automatic Soap dispensor complete all as specified and as directed.

S& F for Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

M&L (SWR) 75mm dia floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single, (single Tee) equal or unequal with access door complete all as specified and directed.

All as per item No 121 here-in-before but dia of 75mm

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed.

M&L for Cement concrete type D2 1:4:8 (using 40mm graded stone aggreages) as in foundations, filling and mass concrete all as specified and directed.

S & F in repair 15mm dia Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S& F in repair Brass Chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S & F 20mm dia gun metal or gate valve with ironwheel head screwed both for iron pipe and fixed complete all as specified and directed.

M&L Providing, reinforced cement concrete nominal mix (1:2:4) type B-1 using 20mm graded stone aggregate in landing, slab etc including formwork complete all as specified and directed.

M&L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S &F aluminium partition with 3mm thick aluminium composite panel at bottom panel and 5.5 mm thick glass on top panel incl glazing clip and neosprene rubber beading as specified and directed including dismantling of old unserviceable aluminium partition complete all as specified and directed.

S &F 3mm thick aluminium composite panel with aluminium frame and shutter as in door incl glazing clip and neosprene rubber beading and complete builders hardwares incl taking down complete all as specified and directed.

S&F rolled setion gde Fe 410 -W (Gde- E- 250) quality as in main and cross beams, hip and jack rafters,purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates incl. rivets or bolt &

M&L for preparing new steel steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L 150 mm bore Salt - glazed stone ware drain pipes, ('A' grade) laid in trenches and jointed as specified.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for all forming branch channel (1/2) round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching, 150mm dia pipe

M&L Plain cement Concrete ( 1:4:8) type D2 bed to 150 mm bore drain pipes including packing under , and haunching against the sides of pipes after they are laid and tested ;in complete all as specified.

S&F vitreous china urinals, flat back of size 465mmX355mmX265mm, white with grating and union for discharge pipe complete all as specified and directed.

Demolition of existing roof treatment of any type

M & L for cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in levelling course etc

M & L 15mm thick screed plaster on RCC slab CM 1:4 with using water proofing compound @ 3% by weight of cement. ( WPC to be measured and paid separately)

M & L for water proofing treatment on roof surfaces in the following manner:- (a) The surfaces shall be painted with hot bitumen grade 30/40 confirming to IS-73 @ 1.20 kg/sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 ltr/sqm. (b) supply & lay 3 mm thick APP water proofing membrane reinforced with non woven polyster matt laid using butane torch by torch on application with a side lap of 10 cm & 15 cm end lap weinghing not less than 3.5 kg/sqm. (c) Applying two coats of aluminium painting over APP membrane.

M&L for applying three coats of white wash over newly plastered surfaces incl preparation in ceilings

M&L for two coats of cement base paint incl preparation of newly plastered surfaces etc complete all as specified

M&L for broken bricks for hardcore of gauge nexc 63 mm, deposited, spread and levelled in layers nexc 15 cm thick watered and rammed to true surface

M&L for aluminium anodised ventilator fixed with refletive type glass, aluminium section weighting 0.55 kg/m incl necessary joining cleats, glazing clips rubber neospeprene at bottom panel and top panel with wire cloth of 0.46mm nominal dia of wire and average with of aperature 1.4mm complete

M&L for 40mm thick PCC 1:2:4, type B0 damp proof course to horizontal or vertical surfaces including necessary formwork.

M&L for plastering 5 mm thick in CM 1:3 over ceilings and finished fair and even w/o using extra cement

M&L for applying three coats of white wash over newly plastered surfaces incl preparation in ceilings

M&L for APP roof treatment 3mm thick of min weight 3.5 kg /sqm over 15mm thick cement mortor over bituminous primer and painted with aluminium paint complete.

S&F 20mm dia unplasticised PVC pipes of pressure tating 10 kgf/cm2 with all fittings and fixed complete to walls and ceilings or laid in floors including taking down of pipe.

S&F 15mm dia unplasticised PVC pipes of pressure tating 10 kgf/cm2 with all fittings and fixed complete to walls and ceilings or laid in floors including taking down of pipe.

M&L Suspended ceiling, comprising 12.5 mm thick reinforced gypsum plaster boards Conforming to IS-2095 , including compele fixing arragements as per manufactures instructions including finishing the exposed surfaces with two coats of oil bound distemper over 2mm thick wall care putty including dismantling of existing ceiling complete all as specified and directed.

M & L for Super heavy series PVC Wall panelling consisting of 5-10mm thick (Hollow) Plain/wood colour PVC sheet as approved including complete fixing arrangments on wall complete all as per manufactures specifications

Taking down carefully aluminium/Copper conductor point wiring (light, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately)and making good disturbed surfaces of walls, floors, etc. to match with the existing good disturbed surfaces of walls, floors etc. match with the existing complete all as specified.

M&L point wiring for one light/fan/exhaust fan point controlled by one way switch by using 1.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including PVC concealed conduits and conduit accessories/fittings, pressed steel terminal switch boxes, 3 mm thick Bakelite sheet top cover (ISI Marked) fitted with Chromium plate brass screws washers and 1.5 Sq mm nominal cross sectional area multistranded copper conductor green PVC insulated unsheathed earth wire and connecting to earth dolly and make wall surfce as existing same colour complete all as specified.

M&L point wiring for one socket outlet point 5 amps on independent board controlled by one, one way switch by using 1.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including PVC concealed conduits and conduit accessories/fittings, pressed steel terminal switch boxes, 3 mm thick Bakelite sheet top cover (ISI Marked) fitted with Chromium plate brass screws washers and 1.5 Sq mm nominal cross sectional area multistranded copper conductor green PVC insulated unsheathed earth wire and connecting to earth dolly complete all as specified.

Ditto all as above item no 157 hereinbefore but one socket outlet point on same baord with other switches with 1.5 sq mm single core multistranded PVC insulated FRLS cable including 1.5 sq mm single core multi stranded copper cable used as continuous earth wire.

M&L point wiring for 15 amps socket point controlled by one, one way switch using 2.5 Sq mm nominal cross sectional area multi stranded copper conductor, PVC insulated FRLS unsheathed cables in and including PVC concealed conduit and conduit fittings including pressed steel terminal switch boxes and 3 mm thick plate for fixing of switches/sockets and fitted with Chromium plated brass screws & washers and1.5 Sq mm nominal cross sectional area multi stranded copper conductor, PVC insulated unsheathed earth wire and connected to earth dolly complete all as specified.

S&F Polycarbonate switch piano flush type, SP,5/6 Amps, one way complete all as specified &directed

S&F Polycarbonate switch piano flush type, SP, 16/20 Amps, one way complete all as specified &directed

S&F Polycarbonate socket out let 2 in 1 socket 5 pin, (6 Amps) flush type controlled by one switch,complete all as specified &directed

S&F Polycarbonate socket out let 6 pin, 20 Amps complete all as specified. & directed

M&L ceiling rose, Pilot 3 Plate ceiling rose 6A,complete all as specified & directed

S&F Ceiling Fan 1200 mm sweep AC 230 volts Five star rating single phase (BLDC Type) making connection with two core flat cable 1.0 sqmm PVC insulated 1100 volts grade multi stranded copper wire of appropriate size including testing complete all as specified

S F Wall mounted fan,BLDC type 300 mm sweep AC 230 volts single phase making connection with two core flat cable 1.0 sqmm PVC insulated 1100 volts grade multi stranded copper wire of appropriate size including testing complete all as specified.

Supply and fixing metal body exhaust Fan 350mm sweep AC 230 Volts single phase with louvers including making connection with three core PVC insulated 1100 volts grade multi stranded cooper wire of appropriate size including testing complete all as specified.

Supply and fixing LED lights fitting 20 watt, 220V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete

S &^ F Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings

S&F plug and socket DBs with Single pole MCBs rated 20 Amps capacity all as specified or equivalent of other make including making niche in wall and mounted flush complete all as specified.

M&L for concealed sub main wiring comprising two single core, 4 Sq mm nominal cross sectional area multi on same copper conductor cable, PVC insulated FRLS Grade unsheathed 1100 Volts grade drawing in and over PVC conduits and conduit fittings complete (concealed type) including S&F 4 Sq mm nominal cross sectional area n green coloure on same copper conductor cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified (Cutting chases and making good of disturbed surfaces shall deem to be including in the unit rate quoted by tendered).(Note :- Extra length of cables/wire required for connection to MCBs shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly)

M&L for concealed sub main wiring comprising two single core, 06 Sq mm nominal cross sectional area multi on same copper conductor cable, PVC insulated FRLS Grade unsheathed 1100 Volts grade drawing in and over PVC conduits and conduit fittings complete (concealed type) including S&F 4 Sq mm nominal cross sectional area n green coloure on same copper conductor cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified (Cutting chases and making good of disturbed surfaces shall deem to be including in the unit rate quoted by tendered).(Note :- Extra length of cables/wire required for connection to MCBs shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly)

S&F distribution board TPN ,with and including of DPX MCCB 25 KA 125 amps MCCB FP, as incomer and SP/TPN going protection class IP 54, 8nway (DPX125+24) with metal double door all as specified and directed. Note: FP MCCBs 25KA 125Apms 1No and 24 Nos MCB SP 32 Apms 230 Volts and Blanking plate shall be measured and under this items.

S&F epoxy powder coated distribution box Double door type SPN 8 way,with 200 amps rated bus bar, 240 Volts for MCBs, grouted flush to walls complete with IP 43 and metal double door all as specified and directed.

S&F epoxy powder coated distribution box Double door type SPN 4 way,with 200 amps rated bus bar, 240 Volts for MCBs, grouted flush to walls complete with IP 43 and metal double door all as specified and directed.

S&F MCB SPN, 40 to 63 Amps , 240 Volts to be housed in DBs Proper and suitable size cable lugs to be fixed with MCBs are including in unit rate of each all as specified and directed

S&F MCB SP 6 to 32 Amps C seires , 240 Volts to be housed in DBs Proper and suitable size cable lugs to be fixed with MCBs are including in unit rate of each all as specified and directed

Taking down existing Gyeser and installing at given location after plastering and replacement of power box etc

Supply & Fixing electric Water Heater Storage type steel bodywith cooper inner tank and heating element upto 2 KW, capacity 25 Ltr. BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV connection piece etc.

S&F epoxy powder coated distribution box Double door type TPN 4 way,with 200 amps rated bus bar, 415 Volts for MCBs, grouted flush to walls complete with IP 43 and metal double door all as specified and directed.

S&F MCB TPN/ FP 40 to 100 Amps B seires , 240 Volts to be housed in DBs Proper and suitable size cable lugs to be fixed with MCBs are including in unit rate of each all as specified and directed

Supply and fixing of Recess LED llight fittings of size 2X2 40 watt LED Made of CRCA powder quoted finish with Fully Covered by PMMA Acrylic Lumio Diffuser, LED Used shall be SMD type and fixture including cutting and making false ceiling of any pattern/mtrl proper fixing of light in falce ceiling , electrical connection up to 15 feet height of various ward and dept all as specified and directed.

Supply and fixing flexible copper cable three core suitable for connection of light fittings/ FTL fittings of any type all as specified.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete

Supplying and laying or fixing in replacement, jointing and testing LT under ground electric power cable crossed linked polyethylene ( XLPE) insulated, galvanised steel strip or wire armoured, ISI-7098 Marked, with aluminium conductor multi stranded , heavy duty 1100 Volts grade of size 10 sqmm cross sectional area, 2 core ,complete all as specified laid in trenches/ laid under floor or fixed naked with walls / on poles/ in ducts /in GI pipes etc. with and including MS Clamps, nuts , bolts, washers complete all as specified and directed. Note :- Excavation, earth work, sand cushioning, protection bricks/ tiles/ block and pipe shall be measured and paid separately under appropriate items.

- do - but of size 16 Sqmm 4 core

- do - but of size 95 Sqmm 3.5 core

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cables, pipes etc. and getting out including trimming the sides and forming bottom surfaces to required levels in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified and directed.

Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified.

Material and labour for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete as specified and directed . Note :- Punned thickness shall only be considered for payment

M&L laying well burnt old size bricks, sub class "B" bricks, straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection all as specified.

S & F GI Pipes galvanized, “light grade ”, laid in trench complete including fittings 50 mm dia.protection for LT Cable.

M&L Earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI strip 32 x 6 mm as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS TMT bars 8mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department.

Supply, installing, commissioing and testing , split Air Conditioner of capacity 2.0 TR (Hot & Cold) and Digital Inverter type with inbuilt air ioniser and plasma filter, rotary compressor,auto clean function, indoor sound level 32 db, front panel display, wireless LCD remote, precoated aluminium fins, , auto fan speed, electric driven , suitable for working on 230 volts, single phase, 50 Hz supply, 5 star rated complete including remote operation complete. The rate is included for following item-: (a) All other connected civil work like hole cutting & other misc work reqd for installation of split AC for proper functioning as directed by EIC. including making good disturbed surfaces as per existing. (b) S&F PVC pipe 15 mm dia transparent flexible heavy duty for water drainage pipe of upto 06 RM at site. (c) S&F copper pipe as per site requirement with insulation of complete pipe with PVC casing & caping of size 75 x 75 mm/reqd size for mechanical protection complete. (d) S&F Wall mounted stand for outdoor unit as suitable for fixing of AC.

S & F sheet metal enclosures with socket plug top and MCBs for single pole and neutral enclosures with a two pin and earth plug and socket complete with one single pole MCB, 240V, 20 Amp for AC point all as directed and specified by Engr-in-charge

Supply & Install Voltage stabilizer automatic boost/buck transformer for low and high voltage with electronic transistorised relay/ time relay for two min , SP, 50 Hz with volt meter indicator digital type and input voltage 170 to 270 and cut up voltage 215 to 240 V cap 4 KVA all as specified.

M&L earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in to ground (earth pit) not less than 2.25 meters deep below GL with top edge of earth plate not less than 1.50 m below ground level, connected to GI lead wire of 4 mm dia. (7.50 m long) by means of nuts, bolts and washers, check nuts of GI and protected by the GI pipe light grade 1.5 mm nominal bore (7.50 m Long) for earth plead wire, watering pipe light grade of 20 mm nominal bore, 0.63 mm thick CI funnel, wire mesh etc complete including necessary earth work and excavation in any type of soil, PCC 1:2:4 type B1 earth pit and Precast RCC cover 50 mm thick dully reinforced with 6 mm dia, MS round bars @ 100 mm C/C both ways, earth testing point, making good to floor complete all as specified.

Supply, installing, commissioing and testing , split Air Conditioner of capacity 1.5 TR (Hot & Cold) Min 3 star with inbuilt air ioniser and plasma filter, rotary compressor,auto clean function, indoor sound level 32 db, front panel display, wireless LCD remote, precoated aluminium fins, , auto fan speed, electric driven , suitable for working on 230 volts, single phase, 50 Hz supply complete including remote operation complete. . The rate is included for following item-: (a) Fixing the cooling unit with grouting nuts, cutting groove to wall for gas pipe & water drainage pipe (b) S&F cutting, bent to shape copper pipe of appropriate size from outdoor unit to indoor unit by cutting holes to wall including brazing the copper pipe fixing union including making good disturbed surfaces as existing. (c) S&F PVC pipe 20 mm dia transparent flexible heavy duty for water drainage pipe of upto 06 RM at site. (d) Insulation of both the copper pipes with insulating material mechanical protection of copper pipe complete. (e) Charging of correct qty of refrigerant gas after necessary brazing/fixing of both the outdoor/indoor unit and testing complete on load to obtain 18 degree celsius temperature at specified amps. (f) All other connected civil work like hole cutting & other misc work reqd for installation of split AC for proper functioning as directed by EIC. (g) outdoor AC portion to be fixed on wall mounted stand as suitable for fixing of AC.

M/s Vatsh Raj and co (BID ID -3313002)

M K Engineers and Contractors (BID ID -3313493)

M/s Highway Construction (BID ID -3313415)

ARORA BROTHERS (BID ID -3313624)

M/S S.B. Singh and Sons (BID ID -3313398)

Sanjay Traders (BID ID -3313048)

M/s Vimal Traders (BID ID -3313898)