PROVISION OF URINAL BLOCK AND TOILET BLOCK AT MRC WELLINGTON AND CERTAIN MINOR WORKS UNDER GE WELLINGTON

Amount

Surface excavation not exceeding 30cm deep and averaging 15 cm deep and getting out as in hard/ dense soil complete all as specified and directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sq m on plan and not exceeding 1.5 m in depth and getting out in hard/ dense soil complete all as specified and directed.

All as per Item No. 02 hereinbefore but exceeding 1.5M and not exceeding 3.0 M deep in any type of soil all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in hard/ dense soil complete all as specified and directed.

Removing excavated soil/ material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and directed.

Plain cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concreting, complete all as specified and directed.

PCC 1:2:4 type B2(using 40mm graded stone aggregate) as in haunching for manhole floor, surface channels and drain complete all as specified and directed.

Pre-cast cement concrete block masnory with solid block exceeding 10cm in width and setting in mortar 1:4 type C1 1:3:6 using 20mm graded aggregate complete all as specified and directed

Pre-cast cement concrete block masnory with solid block exceeding 10cm in width and setting in mortar 1:6 type C1 1:3:6 using 20mm graded aggregate complete (with plain or interlocking joints as directed) setting in motar, complete walls built all as specified and directed

Providing cement concrete type B1, 1:2:4 using 20mm graded stone aggregate as in benching/ coping/ dpc course etc including necessary formwork all as specified and directed.

Providing Precast cement concrete for lintels RCC type B1, 1:2:4 (nominal mix) using 20mm graded stone aggregate set in cement mortar 1:4 complete all as specified and directed.

Mild steel TMT bars 10mm dia and over cut to length, bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

All as per item No 20 hereinbefore but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders all as specified and directed.

Rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Preparation of newly plastered wall surfaces and applying two coats of Oil Bound Distemper over one coat of primer over and including a coat of putty 2-3 mm thick (In two layers) including sanding and preparation and all as specified and directed.

Rendering 15mm (5mm thick in cement mortar 1.4 with WPC over a coat of 10mm thick in cement mortar 1:6) on other than fair faces of brick work or concrete surface including finished even and smooth without using extra cement all as specified and directed.

Supply only water proofing compound all as specified and directed.

Hardcore of broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 150mm thick, watered and rammed to a true surface all as specified and directed.

Plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base to floor 100mm thick all as specified and directed.

25 mm thick Plain cement conncrete 1:2:4, type B-0 using 12.50mm graded stone aggregates as in sub base floors, finished fair and even complete all as specified and directed.

Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match the surface and including 15mm thick screed bed or bedding layer of mortar in cement mortar 1:4 complete all as specified and as directed.

18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigmet to match with shade of granite over 15mm thick screed in cement mortar 1:4 all as specified and directed.

Rounding edges of stone slabs one edge such as steps, cooking platforms and other similar situation, complete all as specified and directed.

Glazed ceramic tiles on vertical surfaces of wall etc, of size 350x250x7mm/ 450x350x7mm set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick in cement mortar 1:4 complete all as specified and as directed.

PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and as directed

Factory made solid panel PVC door shutter 30mm (Stile) consisting of frame made out of M.S tubes for top and bottom rails M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheets to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame all as specified and directed.

Butt hinges, 100 mm size medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section 150 mm long for all as specified and directed.

Extruded aluminium alloy handles 150 mm size, fabricated type, anodised complete all as specified and as directed.

250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

UPVC ventilator frame shall be made of PVC material confirming to IS-10151 the ventilator frame of extruded UPVC section having overall dimensions of 100 x62x50mm having wall thickness 2mm+- 0.2mm. Corners of wall frame shall be joined by MS galvanised brackets joints mitred and plastic welded. The hinge side vertical outer frame shall be reinforced with galvanised MS tube of wall thickness 1mm +/- 0.1mm and the tie rod shall be provide at the bottom of the frame all as specified and directed. Glazing (1) : The ventilator system should be glazed with 5.5mm thick glass of size as required in ventilatior frame (louvered type) as per manufacturer instructions including all fittings and necessary locking arrangements complete all as specified and directed.

Vitreous china squatting pan Orrissa pattern size 580mmx 440mm white with integral foot rest with 'p' or 's'trap including flush pipe PVC 32 mm dia, complete all as specified, making connections to trap and to flush pipe, fixing flushing cistern etc, and making good to floors, complete all as specified and directed

Vitreous china wash down water closet pan (pedestal pattern) white with P or S trap including flushing pipe, seat and PVC seat cover (white) closed pattern with flat bottom and cover brass chromium plated hinging device, including connection to drain and to flushing pipe, antisyhonage pipe etc complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

Vitreous china Counter Wash Hand Basin with fixing accessories, any shape size not less than 480x370x200 mm including brass chromium plated perforated waste coupling/fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, PVC waste pipe of 32 mm bore and of suitable length, 15 mm bore Pillar Tap, cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe and PVC connection 15 mm size with PTMT nuts of length 450 mm and fixed complete all as specified and directed.

Angular stop cock with wall flange chromium plated fancy type for 15 mm bore iron pipe complete all as specified and as directed.

PVC connections 15mm size of length 450mm with PTMT nuts all as specified and directed.

Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges including all as specified and directed.

CP toilet paper holder complete all as specified and directed.

Health Faucet with 8mm dia, 1 m long flexible tube and wall hook with back flow preventer and fixed in repair all as specified and as directed

PVC (SWR) floor/ Nahani trap 75mm outer dia, plain with grating including jointing to waste pipe with solvent cement all as specified and as directed.

Chroumium plated fancy type 2in1 bib tap fixed with existing pipe including all as speicified and as directed

Bib tap fancy type long body chromium plated 15mm dia complete including all as specified and directed

Vitreous China Urinal, Half stall type, white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

Cast copper alloys Chromium plated fancy type Urinal spreader with Auto closing system Push cock ( Urinal Valve) with chromium plated hose pipe fixed suitable for 15mm dia pipe for urinals all as specified and directed.

Supply, laying and testing steel water tubing medium grade galvanized with all GI fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor including cutting and chasing with all fitttings complete all as specified of size 15 mm bore.

Supply, laying and testing steel water tubing medium grade galvanized with all GI fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor including cutting and chasing with all fitttings complete all as specified of size 20 mm bore.

Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layers of capacity 500 Ltrs hoisted and fixed in position with proper inlet and outlet connections all as specified and directed.

Ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed in repairs of size 20mm dia complete all as specified and directed.

Mild steel works in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle) including distance pieces, cleats etc.of grade Fe-410-W (Gde-E-250) quality-A all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed.

Pre- painted galvalume aluminum zinc coating GI based Plain steel sheet as in ridge of 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified and directed.

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

Mild steel Framed work such as grill, grating etc with ends of bars shouldered and /or riveted or forged into spikes, framed guard bars, barred iron door, ladders, framed balusters and simialr work conforming to Fe290 Gde E-165 all as specified and directed.

PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints laid in trenches or in floors all as specified and as directed.

PVC (SWR) bend of any radius 110 mm dia all as specified and directed.

PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints laid in trenches or in floors all as specified and as directed.

PVC (SWR) bend of any radius 75 mm dia complete all as specified and as directed.

PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and as directed.

PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, fixed to walls all as specified and directed.

PVC (SWR) vent cowl 75mm dia bore of pipe complete all as specified and directed.

PVC (SWR) vent cowl 110mm dia bore of pipe complete all as specified and directed.

PVC (SWR) junction single, (single T) equal or unequal of 75mm bore of pipe complete all as specified and directed.

PVC (SWR) junction single, (single T) equal or unequal of 110mm bore of pipe complete all as specified and directed.

Steel water tubing medium grade galvanized with all fittings and laid in trenches / fixed on walls / floors of size 15mm dia all as specified and directed.

Steel water tubing medium grade galvanized with all fittings and laid in trenches / fixed on walls / floors of size 20mm dia all as specified and directed.

32/40mm bore PVC waste pipe suitable for wash hand basin/ urinal complete all as specified and as directed.

75mm thick plain Cement concrete, 1:3:6, type C-1 using 20 mm graded stone aggregate as in plinth protection and hard standing finish even and fair complete all as specified and directed.

Concrete bed to drain pipes including packing under and haunching against the sides of the pipes after they are laid and tested in cement concrete 1:4:8 type D-2 using 40mm graded aggregate for 150mm dia size pipe all as specified and directed.

Salt Glazed stoneware drain pipes of 150mm internal dia, grade 'A' laid in trenches and jointed in cement mortar 1:1 mixed with spun yarn and testing complete all as specified and directed

Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in cement mortar 1:6 complete all as specified and directed. Note :- Reinforcement shall be measured and paid separately.

Cutting and tapping of existing 40mm pipe and inserting a Tee for new connection of size 20mm including reducers requred if any complete all as specified and directed.

Supply and lay pipe galvanized "Medium class" including fittings of size 20mm (3/4") dia all as specified and directed.

Gunmetal globe or gate valve 20mm with iron wheel head screwed both ends for iron pipe of size 20mm dia all as specified and directed.

Ball brass valves high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed of dia 25mm all as specified and directed.

Excavation in trenches not exceeding 1.5M wide and not exceeding 1.5M in depth and getting out in soft/loose soil for laying of under ground cable and foundation of poles.etc complete all as specified and directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. in any type of soil and getting out complete all as specified and directed.

Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 and pointing the dressed surface with same mortar as the work proceeds all as specified and directed.

Extra over stone walling for Hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought up to courses with maximum depression on face from straight edge held against the dressed surface not exceeding 40mm all as specified and directed.

Moorun/ red bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering all as specified and directed.

Plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base to flooring 150mm thick all as specified and directed.

Plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in 50mm thick flooring and finishing the surfaces fair and even without using extra cement all as specified and directed.

Rendering 15mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement all as specified and directed

Flush pointing to Random rubble masonary, uncoursed or brought up to courses using cement mortar 1:4 coplete all as specified and as directed

75mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base floor and finished even and fair complete all as specified and directed.

Machine pressed precast concrete interlocking paver block with grey cement and pigment, of any shape and size conforming to IS 15658 -2006 of 80mm thick M-40 Grade all as specified and as directed.

Plain cement concrete (1:2:4) Type B0 using 12.50mm graded stone aggregate as in kerbs water troughs and the like including weathering , slightly rounded or chamfered angles including necessary form work complete all as specified and directed.

Supply, lay and testing cable XLPE insulated screened PVC bedded, Galvanised steel strip or wire armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 2 Core x 10 Sq mm complete all as specified and directed.

spreading clean dry riddled sand in trenches for cushioning all as specified for cable protection in trenches / ducts complete including watering and consolidation all as specified and directed Note: The punned down thickness shall only be measured.

Brick sub class 'B' to be laid over dry sand cushinoing in trenches as protection to cable all as specified and directed.

GI Pipe light grade 40 mm dia for cable protection in trenches/ at PCC pole for loopin/loop out of cable and cable entry at Bldg/ block end including taking down all as specified and directed.

Demolition of Concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and as directed.

Rendering 15mm thick over stone masonary or surfaces other than of brick work in cement mortar 1:4 all as specified and as directed.

25mm thick Plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate all as specified and directed.

Coloured non - skid Ceramic tiles 7 to 8 mm thick (Square / Rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including Screed bed or bedding layer 15mm thick for laying floor finishes in CM 1:6 complete all as specified and as directed.

Glazed colour Ceramic tiles 7 to 8 mm thick (Square / Rectangular) as in skirting / dadoo set and jointed in neat cement slurry and pointed in white or coloured cement to match over complete all as specified and as directed.

Excavating in post holes (or similar holes) each in hard / dense soil not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removal of excavated materials to a distance not exceeding 50mtr and making good surfaces, complete all as specified and directed

Plain cement concrete 1:3:6 type C2 using 40 mm graded stone aggregate in foundations, filling and posts concrete complete all as specified and directed.

Cutting holes into or through stone walls/ brick wall s bult in cement mortar upto the depth of 20cm and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-I as required complete all as specified and directed.

MS plates (plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes with riveted, bolted or welded attachment complete all as specified and directed.

MS Screw bolts (machine made) with hexagonal or square heads at one ends and screwed the other or screwed both ends, each screwed end to be fitting with washer and one hexagonal or sqaure nut but length of bolt exceeding 5cm but not exceeding 10cm long and dia of shank 11 to 15mm etc all as specified and directed.

Stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc, of required size on the top of the floor or side of waist slab with suitable arrangement all as specified and directed. Note: For payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc..

Roof tiles Mangalore pattern inter locking at side joints, laid dry including dismantling of damaged tiling complete all as specified and diected.

Preparation of old/new surfaces of wall / Manglore tiled roof and applying two coat of Exterior Emulsion Paint/ Tile Guard white or tinted as approved by GE Complete all as specified and diected.

Point wiring complete with 1.5 sqmm (nominal area) FRLS grade PVC insulated, unsheathed stranded copper conductor single core cable 1100 volts grade in and including PVC conduit medium grade complete with conduit fittings/accessories with provn of 1.2 mm thick MS terminal boxes of suitable size and 3 mm thick plastic laminated sheet top cover for housing of switches, sockets etc including 1.5 sqmm FRLS grade PVC insulated unsheathed stranded copper conductor cable for earth continuity conductor and connected to common earth dolly for One light/ fan point controlled by one switch 5Amps SP with cables 1.5 Sqmm size all as specified and directed.

Switch piano flush type 5 A 240 volt SP, one way all as specified and directed.

Ceiling rose 3 terminals PVC/ Poly carbonate isolated body including base block complete all as specified and directed.

LED light fitting 1x20 watt, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Light fitting mirror type with high out put diffuser 2 feet, 10watt 220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Distribution board sheet steel phosphatised powder coated for MCB/DB with copper bus bar and neutral link earthing stud (confirming to IS-13032, IS-8623) 4 way with 200amps rated bus bar single door 240Volt all as specified and directed.

Supply and fixing amps rating 240V, 10KA 'C' curve miniature circute breaker (MCB) of following poles and current carrying in the MCB DB complete with connection testing and commissioning SP 5 to 32 AMP all as specified and directed.

MCB SP 32 Amps, 240 Volts, 50HZ AC supply complete all as specified and directed.

Exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50Hz, RPM 1200, copper winding of Sweep 250mm all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanized earth wire of size 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No 3 connected to earth testing point all specified and directed including testing on completion.

LED building security light fittings of 20Watt including necessary accessories and GI bracket of suitable size complete all as specified and directed. Make: Crompton Cat No LSTS-20-CDL-M or equivalent in Havells/ Bajaj etc.

K.AYYAPPAN

Sree Constructions