REPAIR TO PLINTH PROTECTION CUPBOARD, CHAJJA, PLUMBING INCLUDING PLASTER AND MISC WORKS IN DOMESTIC AND RAKSHA NAGAR AT AF STN OJHAR

Amount

Taking down chowkats or frames exc. 1.5 Sqm but not exc. 4 Sqm each (without taking off shutters from the frame)

Taking down chowkats with shutters (without taking off shutters from the frame) not exc 1.5 Sqm each

Taking down Shutters of any description exc 1sq. m n.exc 2sqm each

S & F Plain solid, straight chowkats and frames of 2nd class HW, wrought framed rebated on the solid,n rounded or chamfered, put togther with glue pinned at joints, supplied and fixed.

S&F Second class hard wood Glazed and skeleton shutters 35mm thick , open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges offraming plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats.

S&F Plain, framed, panelled shutters 35mm thick (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a priming coat of pink primer.

S&F mild steel flats as in hold fasts, grill support to windows and doors

M&L for cutting holes in brick walls built in cement mortar for inserting holdfast and making good dismantled portion in CM 1:3 of cement concrete 1:2:4 Type B-0 (1:2:4), using 12.5 mm graded aggregate ) as required exc half brick but n exc one brick.

S&F Aluminum anodised, barrel tower bolts of extruded section and fixed of 150mm long.

S&F Aluminum alloy anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast - aluminum alloy and fixed of 300mm long.

S&F 100mm butt hinges, extruded aluminium with galvanised MS hinge pin, anodised and fixed Type B-21.

S&F Extruded aluminium alloy handles, fabricated type, anodised,125 mm long

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for 15mm thick rendering in cement mortar 1:4 on fair faces of concrete surfaces finished even and smooth (without using extra cement).

M&L for 10 mm thick rendering in cement mortar 1:6 on fair faces of concrete surfaces finished fair and smooth without using extra cement.

M&L applying two coats of cement based water proofing painting over one coat of primer including prepartion of new surfaces of wall complete all as specified.

M&L Preparing new plastered surface and applying two coats of Oil bond distemper over a coat of chalk whiting or primer.

M&L for repalcing old steel window handles with new steel handles including taking down of old handles including all nuts/bolts/welding etc

M&L for replacing of old stays of steel windows with new stays including taking down of existing stays of complete

S&F in repairs floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor (Overall length of cover plate 150mm).

Supply and Fix window guard bar , plain, let in and fixed independtly in wooden frame conforming to Fe-290 Gde E-165

S & F in repair 4 lever Aluminium Mortice lock, vertical type, size 100 mm

Dismantling boarding any description fixed in position with nails

Supply and fixing Anodised aluminium powder coated (mini thickness of powder coating is 50 micron) frame for windows ,kitchen and cupboard shutters with one or more rebates including jointing cleats for fixing lugs etc complete all as specified.

M & L for 18 mm/ 19 mm thick pre laminated particle board, exterior grade, pre laminated one side with decorative choice lamination and other side blancing white lamination, fixed with screws to timber frame work and directed by Engr in charge

M & L fancy type Aluminium handles 100 mm high of kitchen shutter/Cupboard shutter as approved by E-in-C

M & L fancy type Aluminium CB knobs of kitchen/drawer shutter as approved by E-in-C

M & L for cabinet shutter hinges for door shutters of Cupboard and kitchen shutters of Aluminium type

M & L for magnetic door lock for door shutters of Cupboards and kitchen shutters of Aluminium type

Repairs to leaking water in Bib tap, pillar tap stop cock, single valve of any description by changing the washer etc all as specified.

S&F in repairs 15 mm dia Bib tap chromium plated crutch or butterfly handle screwed down, screwed for iron/pvc pipe or for brass ferrule and fixed.

All as per itme No.34 above but fancy type chromium plated.

S& F in repair 15 mm Bib tap standard of PTMT any colour screwed for Iron/ PVC pipe

S&F in repair Pillar taps 15mm dia brass chromium plated , fancy type with long screwed shanks and fly nuts screwed for 15mm dia pipe all as specified.

S&F in repairs 32mm dia PVC waste pipe for WHB 60 cm long with union all as specified.

All as per ser item Nos 38 above but 40mm dia for sink

S&F Fixed in repairs of PVC valveless, syphonic action type flushing cistern low level, white, with inlet, ball valve, float and handle incl brackets capacity 10 ltrs and connection to pipe complete.

S&F in repair CP Grating doom 125 mm dia with waste hole and making good to floor all as specified.

S&F in repairs PVC connection 15mm dia 450 mm long with 2 Nos brass check nuts with washer etc complete all as specified.

S&F in repairs chromium plated brass shower roses 125 mm size with or without swivel joints including fixing to steel/ pvc pipe or union all as specified.

S&F in repairs wash basin mixer cast copper alloy, chromium plated central hole without popup waste system with 450mm long copper pipe and brass nut including hot & cold water system complete all as directed (Make : Jaquar /Prayag/Plumber or equivalent

Fixing in repair wash basin mixer/ Wall mixer cast copper alloy, chromium plated central hole without popup waste system with 450mm long copper pipe and brass nut complete all as direceted.

S&F in repairs wall mixer cast copper alloy, chromium plated 3 in 1 system with provision for both over head shower chromium plated, with wall flange, screwed down, for iron pipe or for brass ferrule including dismantling of 3 No.concealled stop cock & 2 No. bib cock for each mixer (Make : (Make : Jaquar /Prayag/Plumber or equivalent complete all as specified and as directed by Engineer-In-Charge

M&L for 19-20 mm thick granite slab in any size in black colour, machine cut, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigments to match the shade of granite stone slab including cutting, grinding and polishing with 15 mm thick screed bed in cm 1:4 including demolition existing finish / slab complete all as specified.

Demolition of cement concrete (unreinforcement) as in ground floors or paving n. exc 15cm thick below or above ground level complete.

M&L for 25 mm thick PCC 1:2:4 type B-1 using 20mm graded stone agg as in flooring, pavings finished even and smooth without using extra cement complete.

M&L for 100mm thick PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in sub base

Dismantling of floor, hearth or wall tilings including cement mortar bedding all as specified.

M&L for 15 mm thick screed bed in cm 1:6 as in floor (Upto four storey building) all as specified.

M&L for 10 mm thick rendering in cement mortar 1:4 on fair faces of concrete surfaces for backing of tiles (Upto four storey building) all as specified.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/Rectangular ) area of each tiles exceeding 0.11 Sqm but not exceedng 0.18 sqm, joint free tiles in floors etc .set and jointed neat cement slurry and pointed with colour cement to match.

M&L Vitrified ceramic coloured tiles 10mm thick (square/Rectangular ) area of each tiles exceeding 0.18 Sqm but not exceedng 0.38 sqm, as in floors etc, set and jointed neat cement slurry and pointed with colour cement to match.

M&L for glazed ceramic coloured tiles of size 300x450x7mm thick as in verticle surfaces set and jointed in neat cement slurry and pointed with coloured cement to match.

All as per item 55 above but as in skirting

All as per item 56 above but as in skirting

Demolition of Brick work or stone/boulder masonarybuilt in cement mortor including all quoins, arches, pillars etc.

M&L for walling of Brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius built in cement mortor 1:6.

M & L for cement concrete type C2 (1:3:6) (40 mm graded broken stone aggregate) 75 mm thick as in plinth protection and finish even and fair including form work complete all as directed by Engr in Charge

Dismantling of wall and ceiling boards or insulation boards any thickness including cover fillets etc complete.

S&F Horizontal level suspended ceiling comprising of Armstrong or equivalent GI Clip in micro perforated 600x600mm (nominal size) tiles of 12mm thick galvanized steel as per IS 277(2003) suitable for architectural finishes in 0.5mm thickness as per in IS 513(1994) in global white colour with concealed suspension system having a bevelled edged of 3x3mm and height of 33mm on one side and 18mm on other side. Tile shall have perforation of hole diameter 2.5mm and open area 16% with liner and diagonal pitch of 5.5mm and 7.7mm respectively along with a border of 10mm. The tile shall be electrostatically polyester powder coated using RoHS compliant powder having coating thickness ranging from 60-80microns. Backside of the tile shall have soundtex fleece hot pressed mechanically for uniform bonding to achieve NRC upto 0.7 all as per manufacturers instructions complete all as specified and as directed by Engr-in-charge.

S&F Plain mild steel wire 2.5 mm dia galvanised class 3 in detached work such as hanging of ceiling.

Dismantling plain or corrugated steel sheeting any gauge or thickness

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheeting, 0.50 mm thick, of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws or fixed with L or J type in lieu of screws all as complete as per specified.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheeting, as in ridges, hip, valley gutter etc, 0.50 mm thick, of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws or fixed with L or J type in lieu of screws all as complete as per specified.

M/s.TIRUPATI BUILDERS

M/S PRAMOD SURESHCHANDRA AHER