PWD/BWN/Rs.7.14 lacs/Special repair of Primary Health Centre at Village Lilas in Bhiwani Distt.

Amount

Dismantling cement conglomarate/ terrazzo floor 25 mm to 50 mm thick without concrete base (HSR 8.26)

Scraping of old Cement Plaster HSR(8.32( C)

Stripping and stacking slates or tiles of a roof (HSR 8.10)

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the walls is not to be dismantlled (HSR 8.18) Door

Window

Dismatnling Roofing demolishing mud phaska in tile terracing (HSR 8.8 G)

Scrapping white wash and colour wash (HSR 8.32 (A)

Cement Concrete 1:8:16 with brick ballast 40mm nominal size in foundation and plinth. (HSR 10.26)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position complete in all respects.extra over Item Nos. 10.79 to 10.94, if 1:1 ½:3 mix is used, instead of 1:2:4 (HSR 10.82 +10.95 A)

Top khurra 0.6 m x 0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 over 50 mm thick cement concrete 1:8:16 (HSR 13.50)

Bottom khurra on ground 1:2 m X 0.6 m consisting of brick-on-edge laid in cement mortar 1:3 over 75 mm cement concrete 1:8:16 including 12 mm thick cement plaster 1:3 (HSR 13.57)

Providing fixing PVC Rain water pipe 6Kg Pressure of ISI mark in cement mortar during masonry work. (a) 100 MM dia PVC pipe 6 Kg. Pressure. (HSR 13.89 (a)

Providing and fixing PVC Bend ISI mark. 100mm dia PVC bend HSR(13.90(a)

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coasts of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including routing with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Providing and fixing vitrified tiles of size 600x600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand morter 1.3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note: Tile shall be of premium quality (first quality) of reputed manufacturer like NICTO, KAJA-RIA, SOMANI, ORIENT, JOHNSONS & JOHNSONS. (HSR 14.89)

Providing and fixing vitrified tiles of size600x600 mm of approved make in skirting / dado laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1.3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. HSR(14.90).

Providing and fixing 1st quality ceramic glazed wall tiles conforming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, riser of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (b) Size of ceramic Glazed tiles 300x450mm HSR(14.92(b)q

15 mm thick cement plaster 1:4 on the rough side of single or half brick wall (HSR 15.10)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or matallic or plastered or concrete surfaces to give an even shade. (HSR 16.3)

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. (HSR16.1)

Applying pink primer or aluminium priming ocat on wood work including preparation of surface, Knotting and stopping etc.(HSR 16.2)

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (HSR 16.5)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. (HSR 16.25)

Painting two coats with plastic emulsion paint on walls on new work to give an even shade. (HSR 16.30)

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)]. 1st quality q

Providing and fixing sliding bolt with nuts and screws,etc.,complete iron 250 mm X 16 mm (HSR 17.83 C)II

Factory manufactured panelled door or glazed windows shutters of commercial hard wood such as Hollock, Champ, Chikrassy & Chaplash only. (non coniferous timber other teak, confirming to I.S. pecificationNo. 1003, Kiln seasoned) with 100mm wide vertical styles, 150mm wide lock rail 200 mm wide bottom rail, and 100mm wide other rails, with panels of 15mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screw, chock/cleats, stops nails etc. complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position). (b) 35 mm thick. [HSR 17.90 (b) - Note 1 under 17.18].

Factory manufactured wire gauze door and window shutters of commercial hard wood such as Hollock, Champ, Chikrassy & Chaplash only. (non-coniferous timber other teak conforming to I.S. specification No. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position. (Styles and rails of windows shutter shall be 75 mm wide. (i) 30 mm thick. [HSR 17.92 (ii) - Note 1 under 17.18]q

Cost of aluminium fittings complete for doors and windows, such as tower bolts,handles,etc., and screws for these fittings (excluding sliding bolt) (HSR 17.72 A)

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, lock notch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete door and window frame of size 76 mm X 38 mm with 35 mm wide single rebate (HSR 18.34(b)

Wrought iron and mild steel (using angles, flats, square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors open able or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position (HSR 18.12)

Supplying and fixing glass panes including special metal sash putty of approved make glass panes 4 mm thick, exceeding 40 sq dm areas. (HSR 18.30 B)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge). INDIAN TYPE ORISSA OR ORYA WATER CLOSET SUITE for sinking into floor, with raised foot treads COMPLETE WITH 100 MM G.C.I.’P’ TRAP with or without vent as required and all OTHER NECESSARY FITTINGS as fullydescribed in item no.30.1 above. 630 mm White (HSR 30.2 (B))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE EUROPEAN TYPE WATER CLOSET SUITE WITH CONCEALED ‘P’ or ’S’ TRAP with or without vent (as approved by the Engineer-in-Charge) and all other necessary fittings as fully described in item no.30.3 above. White (HSR 30.6 (i)

EXTRA OVER item nos.30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow black or white plastic seat and lid. White plastic seat (Solid) (HSR 30.13(i))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE LARGE FLAT BACK OR Angular lipped front Urinal 610MM High consisting of. (i)white (HSR 30.25 (i))`

Providing and fixing 25mm thick marble partition for different type of urinals. VITREOUS CHINAWARE PARTITION PLATE white (HSR 30.40 (b)(i))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE size as give below ( to the approval of the Engineerin- charge) including china plug for tap hole where necessary ; R.S. or C.I.BRACKETS for building into wall including painting; 32mm C.P.BRASS WASTE WITH C.P. brass chain and rubber plug; 15mm C.P.BRASS SCREW DOWN PILLAR TAP WITH jam nuts or couplings best design (as approved by the Engineer-in-charge) ALL FITTINGS BEST INDIAN MAKE and; to the approval of the Engineer-in-charge. ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and MAKING GOOD THE WALLS, FLOORS AND PAINTING OF FITTINGS ETC. (HSR 30.41(III)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE VITREOUS CHINAWARE SINKS WITH COMPLETE FITTINGS AS FULLY DESCRIBED IN ITEM NO.30.51 ABOVE. White a) 600mm X 450mm X 200mm (HSR 30.52 (a)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRROR mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall of chromium plated brassclamps with C.P. brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. INDIAN MAKE (i) 600mm X 450mm (HSR 30.71 A I)

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge).(HSR 30.75) (a) Bob cock long body

Bib cock

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer-in- charge) 15 MM STOP COCK (HSR 30.76 (A)

Providing and fixing 15 mm C.P. brass Laboratory cock swan neck of best quality (to the approval of the Engineer-in-charge) One way (HSR 30.78 (A)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE FLEXIBLE TUBE CONNECTION. C.P. Brass (HSR 30.82 (B)II 15 mm X 375 mm

PROVIDING AND FIXINGIN POSITION M.S.OR HEAVY FLAT IRON CLAMPS made out of M.S. flat not less than 5 mm of the approved design for fixing C.I. SOIL WASTE vent or anti pipes to walls COMPLETE IN ALL RESPECTS INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS ETC., AND PAINTING. For 100 mm internal diameter pipes (HSR 30.88(A)

PROVIDING AND FIXING IN POSITION AUTOMATIC BRASS BALL VALVES IN TANKS WITH PEASTIC BALL 20 mm internal diameter (HSR 30.110 (B)II

PROVIDING AND FIXINGIN POSITION GULLY TRAPS FIXED IN CEMENT CONCRETE 1:4:8 complete WITH H.C.I.GRATING 150 MM X 150 MM CAST IRON COVER WEIGHING APPROXIMATELY 7.26 K.G. AND FRAME CLEAR OPENING 300 MM x 300 MM and outside size 330 MM x 330 MM AND CHAMEBR INCLUDING cost of all brick work in CEMENT MORTAR 1:5 CEMENT CONCRETE 1:8:16 IN FOUNDATIONS, AND CEMENT CONCRETE 1:2:4 IN COPING around C.I. cover and frame etc. WITH THREE COATS of black bitumastic superior PAINT of approved manufacture on all C.I. work AS PER STANDARD DESIGN, minimum depth of water should be 150mm with a minimum seal 50mm. 100 mm internal diameter H.C.I. gully trap (HSR 30.114(B)

Providing and Fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers flages for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. (HSR 30.119) 1000 litre capacity

Fee-500 EQR TMT Steel bars for R.C.C. works, where not included in the complete rate of R.C.C. including bending, binding and placing in position complete. (HSR 18.22)

Recovery items: The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer and granular layers have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under :- Brick 6341 Nos. @ Rs. 4/- Each

Brick bats 6.31 Cum @ Rs. 400/- P.Cum Note: All quantities of the above materials have been worked out on the basis of theoretical quantities laid on this road. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual dismantling and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price.

THE SHEETAL CO-OP MULTI PURPOSE SOCIETY LIMITED