8517E8REPAIR TO ROOF FLOORING CEILING SANITARY FITTINGS PERIODIC SERVICES AND OTHER MISC WORKS AT CTI AND OTHER BUILDINGS IN WEST AREA UNDER GARRISON ENGINEER AFJALAHALLI

Amount

Taking down cement plaster including raking out joints hacking for key, scrubbing down with water etc.

Demolition of brick work built in cement mortar or cement lime mortar and archor pillars etc but excluding ashlar facings dressed stone work and pre cast concrete articles.

Material and labour for PCC block masonry with solid blocks 1:3:6 type C1 using 20mm graded stone aggregate exc 10 cm in width and setting in mortar 1:6 complete.

Material and labour for PCC solid buiding blocks 10 cm thick Pcc 1:3:6 ,Type C1 using 20 mm graded aggregate and setting in mortar 1:4

Material and labour for 15mm thick rendering in CM (1:4) on brick or concrete wall surface finished even & fair without using extra cement as in Wall with water proofing compound (Water proofing compound measured and paid separately).

Suppy only for liquid water proofing compound

Material and labour for 10mm thick rendering in CM (1:6) on brick or concrete wall surface finished even & fair without using extra cement as in Wall.

Material and labour for 5mm thick rendering in CM (1:3) on brick or concrete surface on ceiling , finished even & fair without using extra cement.

Material and labour for three coats of white washing on walls including preparation of new plastered surface.

Material and labour for three coats of white washing on ceiling including preparation of new plastered surface.

Material and labour for two coats of distembering on new plastered surface including preparation of new surface.

Material and labour for two coats of cement based paint on new plastered surface including preparation of new surface.

Material and labour for one coats of white washing on including preparation of old plastered surface to match the existing surface.

Demolition of Cement concrete (unreinforced) in ground floor and pavings not exc. 15 cm thickness (below or above GL).

Material and labour for 75 mm thick PCC 1:3:6 type C-2(using 40 mm graded mechanically crushed stone aggregate )as in subbase , paving and plinth protection finished even and smooth without using extra cement.

Material and labour for 40 mm thick PCC 1:2:4 type B-1(using 20 mm graded mechanically crushed stone aggregate )as in flooring finished even and smooth using extra cement.

Material and labour for 25mm thick for cement concrete type B-1, 1:2:4 (20mm graded agg) as in flooring finished rough fair receiving toping layer of tiles.

Demolition of re inforced cement conc of any description and in any position not otherwise specifically provided.

Material and labour for Reinforced cement concrete (nominal mix) in Type B1 1:2:4 (20 mm graded aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like incl form work.

Material and labour for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Material and labour for Mild steel TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Material and labour for MS tubular medium grade as in posts, purlins including distance pieces, cleats etc complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240

Material and labour two coats of synthetic enamel painting over a priming coat of red oxide, zinc chrome primer incl preparation of previously untreated new surfaces of steel and iron exc 10 cm width or girth.

Taking down wooden Shutters of any description n exc 1 sqm each and refixing same opening.

Taking down wooden shutters of any description exc. 1 Sqm and n. exc 2 sqm and refixing same opening.

Taking down wooden Shutters of any description n exc 1 sqm each

Taking down wooden shutters of any description exc. 1 Sqm and n. exc 2 sqm

Taking down wooden chowkhats or frames with shutters area exc. 1.5 Sqm and n.exc 4 sqm each and removing from the site

Taking down wooden chowkhats or frames with shutters area n exc. 1.5 Sqm each and removing from the site

Taking down wooden chowkhats or frames area n exc. 1.5 Sqm each and removing from the site

Taking down wooden chowkhats or frames area exc. 1.5 Sqm and n.exc 4 sqm each and removing from the site

Dismantling of fillets ,rails,post,rafter,purline etc.under 40 sq. cm in section.

Material and labour for plain fillets ,square ,rectangular or triangular in sec Exc 13 & n. exc 25sq cm clean sawn secured with nail or screwed to fixed shelves 2nd class HW.

Material and labour for 2nd class HW Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

Supply and fixing for 35 mm thick 2nd class HW factory made panelled shutters with panel of 12 mm thick reneered commercial plywood kilnseasoned chemically treated with 15 x 6 mm twedging all around the panels.

Supply and fixing for Glazed and skeleton shuttrs of 2nd class hard wood 30 mm thick shuttrs, open rebated and prepared (receive glass, gauze etc (without sash bars) edges of framing plane, chamfered or rounded, fitted with cut and miltered beeds for securing glass etc, size of members of shutters as specified in SSR Part I Section 8 Clause 8.20 (a) supplied and fitted to chowkhats.

Ditto all as per item No 37 above but divided into squares and rebated sash bars any numbers.

Material and labour for preparing surfaces of wood and wood based materials, steel and iron work, new or old of any description and girth not otherwised described and treated with tar or coal tar black paint.

Supply and fixing mild steel hold fasts conforming to Fe 290 grade -E--165.

Supply and fixing Factory made PVC choawkats or frames of size 50x 47mm with wall thickness made out of extruded 5 mm rigid PVC foam sheet mitered at corner and jointed with 2 Nos of 150mm long brackets of 15mm x MS square tube the vertical door prattles to be reinforced with 19 x 19 mm MS square tube of 19 gauge EPDM rubber gasket door frame to be fixed to wall using MS screws of 65/100mm size complete as per manufacture’s specification

Supply and fixing Factory mode 30 mm thick PVC paneled door shutter, manufactured by M/S rajshree or equivalent ,made from MS tube of 19 gauge x 19 mm x 19mm for styles and 15mm x for top & bottom rails, covered with heat molded PVC channel of 5mm thick sheet and 30x 50mm wide to from styles and 5mm thick x 75 mm wide PVC sheet for top rail and lock rail on either side and 5mm thick x200mm wide crass PVC sheet as gap insert for top rail and bottom rail paneling of 5mm thick PVC sheet fitted with MS frames welded/sealed to styles and rails with PVC sheet beading either side jointed together

Supply and fixing MS butt hinges medium weight cold rolled 100 mm size

Supply and fixing for 75mm long butt hinge.

Supply and fixing Alu anoldised handle 150 mm long.

Supply and fixing Alu anoldised handle 125 mm long.

Supply and fixing Alu anoldised barrel tower bolt 200 mm long.

Supply and fixing Alu anoldised barrel tower bolt 125 mm long.

Supply and fixing 300 mm (length of bolt) mild steel sliding door bolt (bolt type) above enameled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate.

Supply and fixing Galvanised MS wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tack or galvanized wire staple and including fixing with beads supplied with joinery when fixed in repair incl MS Flat 15 x 3 mm thick with hole to receive wire mesh incl nut bolt

Material and labour two coats of synthitic enamel paint over a priming coat of pink primer incl preparation untreated surfaces of wood or wood based material exc 10 cm width or girth

Shutters of any description n exc 1 sqm each Resecuring or easing & adjusting, without taking down

All as per item No 52 above but exc 1 sqm and n exc 2 sqm each

Supply and fixing in rep 150 mm size mild steel helical door spring including roller and roller plate fixed to wooden/steel choukhat or frame with screw/welding complete fixed in repairs.

Supply and fixing in rep125 mm long Mild steel barrel tower blots, stove enamelled black, with bright bolt and fixed

Supply and fixing in rep 150 mmlong Mild steel barrel tower blots, stove enamelled black, with bright bolt and fixed

Supply and fixing in rep 300 mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed

Supply and fixing in repairs galavanised MS wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18 mm in repairs.

Hacking out old broken glass pane any thickness any size from wooden/steel window frames

Supply and fixing for sheet glass 3 mm thick ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane

Dismantling of timber scantling 40 Sq cm and over in section in any position in framed work

Material and labour for Second class hard-wood in scantlings clean sawn fixed to RCC, wooden post and wooden purlins incl drilling for nut and bolt

Material and labour for preparing surfaces of wood and wood based materials, new or old of any description and girth not otherwised described and treated with creosote oil .

Supply and fixing for 1 st class hard wood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles n exc 200 cu. cm each

Material and labour for 2 cost of synthetic enamel painting over acoct of primer to small fitting incl preparation.

Dismantling wall and ceiling boards any description, any thickness, including cover fillets and frames

Material and labour for 8 mm thick gypsum building boards of size 595 x 595mm along with including PVC laminated at back side of board fixed or laid / inserted to anodised aluminium snap grid of size 605mm x 605mm frame work for false ceiling with screws fixed to false ceiling including hangers 6 mm dia G.I (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long completeall as specified and as directed.

Material and labour for 6 mm thick ceiling with calcium silicate board of silicon and calcareous material reinforced with cellulose fibre for fixing in 600 x 600 mm fixed to exposed metal frame/alu frame grid (

Dismantling of AC or corugated, semi corugated,etc. Sheet roof coverings

Supply and fixing 6 mm thick asbestos cement, corugated or semi corugated sheets in roofs, walls etc. fixed with L type or J type or cank hook bolts.

Supply and fixing Asbestos cement two piece adjustable plain wing ridge 6mm thick fixed with L type or J type or crank hook bolts.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to roof covering/cladding to wall, fixed with self tapping screws as specified.

Supply and fixing Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Supply and fixing 0.63 mm galvanised, corrugated Mild Steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in lieu of screws.

Supply and fixing for 0.63 mm plain mild steel sheeting in ridges, hips, valley gutters, drip and straight flashing with grade of zinc coating 275.

Demolition and bracking up drain pipes 100 mm dia (salt glazed ware, AC or PVC, reinforced concrete) set in cement mortar incl bend and dimension piece etc. Complete.

All as per item No 77 above but 75 mmdia of pipes.

Supply and fixing 110mm bore PVC pipe (SWR) single socketed in any length with rubber ring joints fixed to wall complete all as specified.

Supply and fixing 75mm bore PVC pipe (SWR) single socketed in any length with rubber ring joints fixed to wall complete all as specified.

Supply and fixing in repairs for PVC (SWR) bend 110 mm dia

Supply and fixing in repairs for PVC (SWR) bend 75 mm dia

Excavating in trenches in exc 1.5mtrs wide and n exc 1.5mtr depth for drain find n exc 10sqm on plan and n exc 1.5m on depth and getting out soft/loose soil.

Returning filling including, spreading, leveled, watering and well ramming in layers not exc 25 cm.

Removing excavated materials n exc 50mm and depositing where directed at a level n exc 1.5m above the starting point.

Dismantling floor hearth or wall tiling including cement mortar bedding but incl screed bed and plaster.

Material and labour for Granite 20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl screed or bedding layer of mortar 15 mm thick in cm 1:4 for laying floor finishes complete .

Supply and fixing non skid tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding .11 sqm but not exc. 0.18 sqm in floor etc. set and jointed in neat cement sullery out pointed in white cement to Match incl screed or bedding layer of mortar 15 mm thick in cm 1:4 for laying floor finishes

All as per item No 88 above but vertical surfaces incl 10 mm thick cement plaster in cm 1:4

Material and labour for non skid tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 sqm but not exc. 0.11 sqm in floor etc. set and jointed in neat cement sullery out pointed in white cement to Match incl screed or bedding layer of mortar 15 mm thick in cm 1:4 for laying floor finishes

Material and labour for glazed ceramic designer coloured tiles of size 300 X 200 X 7 mm thick as in vertical surface such as skirting / dado, set, jointed in neat cement slurry and pointed in white cement using pigment to match color of tiles incl 10 mm thick plaster in CM 1:4 complete all as specified & directed

Supply and fixing for Vitrified ceramic tiles 10mm thick dark shade (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed or bedding layer of mortar 15 mm thick in cm 1:4 for laying floor finishes

All as per item No 92 above but vertical surfaces incl 10 mm thick cement plaster in cm 1:4

Supply and fixing for kota stone slab 20 to 25 of size 600 x 600 mm thick (Pre grinded and polished) bedded, jointed and painted with grey cement slury incl cutting and grinding/polishing incl 15 mm th 1:6 CM bedding layer incl dismantling.

Supply and fixing for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed incl 10 mm thick plaster in CM 1:4 complete all as specified & directed incl dismantling

M/L machine cut cudappa stone slab 20-25 mm thick in perairs over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match to shade of slab including rubbing and polishing and 15 mm thick screed in cement motar 1:4 complete all as specified complete incl dismantling

Rounding to edges of cudappa stone slab on edge,such as in steps ,cooking plateform ,and other similar situation

Material and labour for machine pressed precast conrete interlocking paver block any shape and size confirming to IS-15658-2006 of 60 mm thickness, M-35 grade with grey cement and no pigment incl dismantling.

Material and labour for 50mm Sand filling under floors or in foundations including watering and consolidation, Spreading and levelling in layers n exc. 25 cm thick and well ramming including watering as required

Supply and fixing for Cement concrete chequered pre polished any coloured tiles 30cm x 30xm x20mm to25 mm thick, machine pressed; set, jointed and pointed in net coloured pigment in floors,incl screed or bedding layer of mortar 15 mm thick in cm 1:4 for laying floor finishes incl dismantling

Supply and fixing for 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification

Supply and fixing for Insulated PVC Wall Lining consisting of PVC Insulated Panels with wood grain printed PVC sheet used instead of plain colour sheet. Having expanded polystyrene (EPS) stuck to 2mm thick plain colour PVC sheet duly fitted into the wall as per specifications and drawing

Supply and fixing in repairs for Fancy type powder coated curtain rod 20 mm dia fixed with brackets.

Supply and fixing in repairs for 100 mm Cast iron or malleable cast iron handles, cast type, stove enamelled black

Supply and fixing for Cast iron (malleable or mild steel) Casement stays, size 300mm, with hinged joint and two plates, with studs complete Add if fixed to steel sashes, including drilling necessary holes or welding

Material and labour for glass dividing strip 38 mm x 3mm thick , inserted in position in PCC floor

Repairs to locker of sorts by removing the following existing unserviceable steel members and providing new members uncluding painting to the structure of locker all as specific and shown on drawing FD-1029(Note : Handle, Hinges and locker painting measured under Item 108 to 110 here in after)(i) 75 mm long hasp & staple chromium plate of size 75 x 40 x 3 mm

Supply and fixing 100mm long chromium plated steel handle

Supply and fixing 70mm long steel projecting type hinges incl welding

Duly spray painting with two coat of approved synthetic enamel paint to the locker colour as approved by GE

Taking up or down steel tubing and connector 15 mm bore in new or old position (wall ceiling floor etc)

Taking up or down steel tubing and connector 20 mm bore in new or old position (wall ceiling floor etc)

Taking up or down steel tubing and connector 25 mm bore in new or old position (wall ceiling floor etc)

Re-fixing only steel water tubing 15mm bore.

Re-fixing only steel water tubing 20mm bore.

Re-fixing only steel water tubing 25mm bore.

Supply and fixing GI tubing 15 mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors.

Supply and fixing GI tubing 20 mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors.

Supply and fixing GI tubing 25 mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors.

Supply and fixing in repair 15 mm dia Pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-110gms))

Supply and fixing in rep 15mm bore stop value of PTMT of any colour screwed for iron pipe comp.

Supply and fixing in rep 20mm bore stop value of PTMT of any colour screwed for iron pipe comp.

Supply and fixing in rep 20 mm Stop valves, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed

Supply and fixing in rep 15mm bore stop valves cast copper alloy fancy type chromium plate with long shank & cup (concealed type).

Supply and fixing in repairs PVC connections 45 cm long incl 15 mm bore fly nuts on both ends complete

Supply and fixing in repairs Bib tap standard or PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm 90gms/20mm-125gms)

Supply and fixing in rep pvc flexible Waste pipe 32mm dia

Supply and fixing in rep pvc flexible Waste pipe 40 mm dia

Supply and fixing in repairs taking down high/low level cistern with brackets flush pipe etc complete and supply and fixing PVC low level cistern syphonic action type including inlet ball valve float and handle including brackets of approved make including all connectionSupply and fixinglush pipes for EWC & indian type WC.

Supply and fixing in repairs 75 mm CI floor trap with CP grating incl jointing to waste pipe incl fixed in cement conc block 30x30x30cm type B1 1:2:4

Supply and fixing in repairs stainless steel single bowl with drain board type sink with waste coupling waste pipe complete of overall size 495x420 mm with bowl size 410mmx330mmx160mm .

Supply and fixing in repair viterious china white wash hand basin flat back white in colour ISI marked of size 550 mm x 400 mm with chromium plated waste coupling and PVC waste pipe fixed to walls with CI brakets 2 Nos embedded in CM 1:4 type B-1 size 30 xm x 20 cm x 20 cm complete.

Supply and fixing in repairs viterous china squatting pan Orrisa pattern size 580 x 440 mm white with "P" and "S" trap front or back inlet etc incl provisioning of lime concretes

Supply and fixing in repair vitreous china wash down water closet, padestal pattern, white in colour incl white seat cover ISI marked 'P' or 'S' trap, fixing bolt and jointing.

Supply and fixing in rep for Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) Self-closing taps, cast copper alloy, chromium plated, screwed for iron pipe and fixed waste coupling of PTMT (half or full threaded) Minimum weight 32mm-45gms)

Cutting into existing manhole bore 100 mm SGSW pipe and making good

Supply and fixing in repair brass PTMT shower rose 75 mm dia .

Supply and fixing in rep stainless steel grating openable 150 mm dia with or wihout hole for wate pipe incl fixing with white cement

Supply and fixing in repairs Health faucet CP for iron pipes 15 mm bore with all accessories complete.

Material and labour in repairs for Providing precast cement concrete Typa B1 1:3:6(12.5 mm graded stone aggregate) set in CM 1:4 louvres and jallies, 25mm thick (measured solid), including all mouldings

Material and labour for providing and injecting emulsion for Anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litres per linear meter including drilling and plugging holes etc, in Apron.

Material and labour for providing and injecting emulsion for Anti termite treatment at points of contact of wood work by chemical emulsion (water based solution) at the rate of 0.50 litres per hole by drilling 6 mm dia , holes at a down ward angle.

Removing complete existing treatment on roof surfaces surfaces by picking , sweeping clean and washig down with water to remove dust, etc.

Material and labour rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 and even and smooth without using extra cement including mixing of water proofing compound wherever require(WPC measured separately).

Material and labour for water proofing treatment on horisontal and vertical surfaces with applying of oil bound bituminous primer @0.20 Kg/Sqm and providing 4 mm thick APP modified water proofing membrane weighing not less than 4.00 kg/sqm reinforced with non woven polyester matt weighing not less than 160 gms/sqm including minimum 10 cm side over laps and 15 cm end lap torch sealed and bonded as per detailed procedure on note No 6 of TD drawing No AFB/TD/260/06 sheet No 1/1(R) and applying a coat of blown grade @1.2 kg per sqm hot bitumen 90/15 over and below the membrane finished with solar reflective bituminous aluminium paint/primer @0.1 Kg per sqm all as specified and as directed.

Material and labour for Providing, cement concrete 1:3:6 type C1( using 20 mm graded stone aggt) in window or door cills, lintels, bressummers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc.(of any section indicated), with plain fair faces, including chamfers weatherings, throating etc. and setting in mortar complete with joints to match

Material and labour for preparation of old decorated wall surfaces and applying one coat of white wash all as specified

All as per item No 148 here-in-before but on ceiling

Material and labour for washing, rubbing down and stopping of distempered surfaces of walls and applying one coat of distemper oil emulsion all as specified

Material and labour for Complete removal of existing treated surface finishes and applying 2 mm avarage thick Birla care wall putty including filling up of all nail holes,one coat of primer and applying two coat of OBD all as specified and directed

Material and labour for washing, rubbing down and stopping of distempered and painted surfaces of walls and applying one coat of cement base paint all as specified

Material and labour for preparation of old painted wall surfaces and applying one coat weather proof paint all as specified and directed

Material and labour for preparing old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and directed

All as per item No 154 hereinbefore but on steel surfaces.

Supply and fixing in repairs plastic water closet seat cover, black/white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device.

Supply and fixing in repairs Aluminium (extruded section ) body Door closer hydraulically regulated,designation No. 3,universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

S R Trading Co

Sri Lakshmi Venkateswara Enterprises

SREE BUILDERS

Vivek Constructions

VARGHESECHACKO AND CO