COMPREHENSIVE MAINT AND REPAIR IN THE AOR OF POCKET NO. 05 AT MIL STN JAISALMER

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premise complete all as specified and directed by Engineer-in-charge.

M&L for Chipping of 25-30 mm average thickness unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead. further applying polymer based bond coat on the prepared old surface of concrete /masonry to receive new polymer mortar/polymer modified mortar with two coats of Thermax TM Bond AR as per manufacturer specifications. Laying of polymer modified mortar shall be completed within the overlay time of bonding coat. This bond coat act as bonding agent between old and new concrete. further applying to the damaged concrete portion of slab / columns / beams / chajjas / parapet / roof projection/balcony/staircase with single component, fiber reinforced, dual shrinkage- compensated thixotropic, cementitious patch repair polymer modified mortar Thermax BS 5F (having the technical parameters mentioned in material specifications ) capable of applying up to 25-30 mm thick in single layer initially by hand and finishing with troweled carefully compacting the same around the rebar and finishing to bring it in line with existing concrete surface with an average specified thickness. its material consumption is 50kg/sqm for 25-30 mm thickness, all as specified and directed as Engineer-in-Charge. Note : The quoted rate by the contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20 mtr height.

M&L for Chipping of 5-10 mm average thickness unsound/weak concrete material from slab with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead. further applying polymer based bond coat on the prepared old surface of concrete /masonry to receive new polymer mortar/polymer modified mortar with two coats of Thermax TM Bond AR as per manufacturer specifications. Laying of polymer modified mortar shall be completed within the overlay time of bonding coat. This bond coat act as bonding agent between old and new concrete. further applying to the damaged concrete portion of slab/ chajjas / roof projection with single component, fiber reinforced, dual shrinkage- compensated thixotropic, cementitious patch repair polymer modified mortar Thermax BS 5F (having the technical parameters mentioned in material specifications ) capable of applying up to 25-30 mm thick in single layer initially by hand and finishing with troweled carefully compacting the same around the rebar and finishing to bring it in line with existing concrete surface with an average specified thickness. its material consumption is 50kg/sqm for 25-30 mm thickness, all as specified and directed as Engineer-in-Charge. Note : The quoted rate by the contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20 mtr height.

M & L for Chipping of 12-15 mm average thickness unsound/weak plaster concrete material from slabs, beams, columns/break work, masonery wall etc. with manual Chisel or by standard power driven percussion type machine of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed surface with wire brushes etc. and disposal of debris for all lead. further applying 12-15 mm Ready to use plaster of approved make. Its excellent replacement to conventional plaster and conforms to IS 1661-1972, IS 2250-1965, IS 2402-1963, It can be applied using trowels or spatula like in conventional system. can be applied for 15 mm thickness in a single layer for thickness above 15mm multiple layer is recommended. Water powder ratio is 16-19% by weight, compressive strength @ 28 days in 10-12Mpa, Material consumption 20-25kg/Sqm for 12-15mm thickness, complete all as specified and directed by Engineer-in-charge. Note : The quoted rate by the contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20 mtr height.

M&L for Cleaning & applying rust remover of approved make in two coats over rusted reinforcement surface and providing anti corrosive coating with two component epoxy based zinc rich primer/Rust passivation Inhibitor coat at the rate of 6-8 sq. mtr/ltr not less than 50 microns dft with Sika friazinc R or equivalent to reinforcement surface as per manufacturer’s instructions including all scaffolding, machinery, tools tackles and clearing of debris complete all as specified and directed by Engineer-in-charge.

M&L for Shear Connectors by drilling 12mm dia holes up to a depth of 75mm maximum and fixing 8mm dia L shaped anchor rods as shear connectors at every 300mm c/c on the surfaces of the columns/beams or any other structural member as the case may be. Clean the same using air or blower and make sure that there are no fine particles present in the hole and filled the holes with one or two component styrene free vinylester resin anchor or two components, styrene & cement free epoxy- acrylate fixing and anchoring compound. At this stage push the shear connector gently in to the hole and finish the excess resin which comes out of the hole and allow the shear connectors not to be disturbed for Minimum 20 minutes complete all as specified and directed by Engineer-in-charge. Note : Reinforcement shall be paid separately.

M&L Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips including dismantling of existing bar complete all as specified and directed by Engineer-in-charge. Note : Additional Reinforcement: In the case of the shear reinforcement also, if the diameter of the rebars are reduced, provide 8mm dia stirrups in the form of 2 "U" shaped bars. Tie them properly so that it has a tight contact with the main bars.

S&F chicken mesh wire netting 25 gauge supplied and fixed on wall ceiling with nails complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered surface and applying two coat of white or tinned with cement base paint over priming coat on exterior wall complete all as specified and directed by Engineer-in-charge.

M&L Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces of wall and applying 1mm thick of Birla white wall care putty to achieve smooth surfaces and applying two coats of distemper oil emulsion of approved shade/tint over a coat of compatiable priming paint complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces of ceiling and applying two coats Oil Bound Distemper of approved shade/tint over a coat of compatiable priming paint complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed by Engineer-in-charge.

M & L for preparation of newly plastered surfaces of wall /ceiling and applying 1mm thick of Birla white wall care putty to achieve smooth surfaces complete all as specified and directed by Engineer-in-charge.

M & L for applying two coats of Oil Bound Distemper of approved shade/tint over a coat of compatiable priming paint complete all as specified and directed by Engineer-in-charge.

Complete removal existing treatment and applying 1mm thick of Birla white wall care putty to achieve smooth surfaces and applying two coats of Oil Bound Distemper of approved shade/tint over a coat of compatiable priming paint complete all as specified and directed by Engineer-in-charge.

M& L plain cement concrete 1:2:4 type B0 by using 20mm graded stone agregate (25mm thick) as in flooring with water proofing compound @ 2% dosage (1kgs) in 50kg cement including demolition of cement concrete un -reinforced in ground floors and pavings n.exc 15cm thickness complete all as specified and directed by Engineer-in-charge.

Supply of SBR based waterproofing compound @ 2% dosage by weight of cement (1kgs) of 50kg cement used to be mixed in cement concrete as water proofing and hardening complete all as specified and directed by Engineer-in-charge.

M & L Polythene film, 50 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m. Note : All above operations to be done in presence of auth applicator in order complete all as specified and directed by Engineer-in-charge.

M&L for Non - skid colored ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in floors etc. by fixing with 6-8mm thick bedding of TYPE2 tile adhesive Make: Ultratech TileFixo range and pointed in epoxy grouing only for laying floor finishes complete all as specified and directed by Engineer-in-charge. Note : Work will be in patches or in bulk complete all as specified and directed by Engineer-in-charge.

M&L for Coloured Glazed ceramic tiles in vertical surface 450X 300X 7mm thick set, by fixing with 6-8mm thick bedding of TYPE2 tile adhesive Make: Ultratech TileFixo range set and pointed in epoxy grouting. incl dismantling of wall tiling including backing coat if any, removing rubbish off the premises complete all as specified and directed by Engineer-in-charge.

M & L for double charge, stainfree, vitrified tiles, Premium (1st) quality straight edge, coloured tiles 600 X 600 mm and 9-10 mm thick, as in floors etc. in any pattern of light coloured tiles as in approved shade, set in neat cement , including 6-8mm thick bedding of TYPE2 tile adhesive Make: Ultratech TileFixo range and pointed in white coloured cement to match, in floors etc.dismantling floor, removing rubbish off the premises and other necessities of job complete all as specified. Note : Work will be in patches or in bulk complete all as specified and directed by Engineer-in-charge.

All as per item No 22.00 here-in-before but as in skirting, steps etc in vertical surfaces with 6-8mm thick bedding of TYPE2 tile adhesive complete all as specified and directed by Engineer-in-charge.

M & L for Non - skid Ceramic colour tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including including including dismantling floor, removing rubbish off the premises and other necessities of job complete all as specified and directed by Engineer-in-charge. Note : Work will be in patches or in bulk

All as item No 24. above but as in skirting, steps etc in vertical surfaces with 6-8mm thick bedding of TYPE2 tile adhesive complete all as specified and directed by Engineer-in-charge.

Material & Labour for ceramic out door tiles 300mmx300mmx10mmm thick digital design set, jointed and pointed in neat cement slurry as in floors with grey cement over & including over screed bed or bedding layer of mortar 15 mm thick Cement Mortar 1:6 complete all as specified and directed by Engineer-in-charge. Note : Work will be in patches or in bulk

M&L for Machine cut kota stone slab flooring 20-25mm thick over, laid over cement screed base , jointed and pointed with grey cement slurry mixed with pigment over 20mm thick cement mortar 1:6 screed bed to match the shade of the slab including rubbing and polishing including dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid beded and pointed in any morter complete all as specified and directed by Engineer-in-charge.

M&L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar over 10 mm thick cement plaster 1:3 jointed and pointed with grey cement slurry mxed with pigment to match the shade of the slab including rubbing and polishing including dismantling Stone slabs and tiles of any description or thickness laid beded and pointed in any morter complete all as specified and directed by Engineer-in-charge.

M & L for Mirror polishing on old marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as specified and directed by Engineer-in-charge.

M&L for providing precast cement concrete (1:2:4) type B-2 (using 20mm garded stone aggregate) in copings. apex stones, columns, posts, boundary pillars, frame of jallies etc and setting in cement mortar (1:4) complete with joints to match complete all as specified and directed by Engineer-in-charge.

Dismantling of Trellis work (Jafri)/post, including taking as under of battens in trellis complete all as specified and directed by Engineer-in-charge.

M& L providing Stone jalies Jaisalmer type 48-50MM thick and 60 cm high fixed in line including stone pillar having size 100 x 100 MM height 70 CM fixed in cement mortar 1:4 fixed on stone runner beam (stone piller measured with Jali) including filling of joints with pigment of same colour complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete in ground floors and pavings in any specification n.exc 15cm thickness complete all as specified and directed by Engineer-in-charge.

M&L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded agg) as in plinth protection incl finishing even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for 25mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregates) as in flooring complete all as specified and directed by Engineer-in-charge.

M&L for 75mm thick PCC 1:2:4 type B2 (using 40mm graded agg) as in floor incl finishing even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for Precast cement concrete 1:3:6 type C1 (Using 20 mm graded granite stone aggregate) block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6 including demolition of brickwork or stone/ boulder/block masonry and built in cement mortar including all quoins arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified and directed by Engineer-in-charge.

M&L for rendering 15 mm thick readymade plaster on inner/outer walls with Ultra Tech READIPLAST by adding 17-19% of potable water by weight of material. For thickness above 15mm is recommended to be applied in multiple layers, Ready-mix plaster shall complies with IS-1661-1972, IS 2250-1965, IS 2402-1963 and confirms the compressive strength @ 28 Days-10-12 Mpa/ Bulk density 1500-1800 Kg/m3 complete all as specified and directed by Engineer-in-charge. Note : The quoted rate by the contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20 mtr height.

M&L Granite (Jodhpur Red) work (table rubbed and polished) for wall lining / partition b/w urinals and for counter wash basin 10mm thick in cement mortar (1:4) and pointing / fixing with epoxy grouting only using marble dust with admixture of pigment to match with shade of granite including cleaning of damaged granite and fix with epoxy grouting only.including dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid beded and pointed in any morter complete all as specified and directed by Engineer-in-charge.

M & L for Jaisalmer stone for wall cladding (of any type) 35-55 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of stone, exc .0.06 sqm but not exc 0.11 sqm ,including cutting and polishing types in wall including 20 mm thick CM 1:4 for laying Jaisalmer stone including dismantling of existing any type of stione complete all as specified and directed by Engineer-in-charge.

Supply & Fixing 15mm bore tubes medium grade galvanized with all fittings such as Tee, elbows, sockets, unions, plugs, short lenghts etc. and fixed complete to walls and ceilings or laid in floors concealed or open of any length including taking down or up existing GI tubing & connections complete all as specified and directed by Engineer-in-charge.

Supply & Fixing 20 mm bore tubes medium grade galvanized with all fitting such as Tee, elbows, sockets, unions, plugs, short lenghts etc and fixed complete to walls and ceilings or laid in floors of any length including taking down or up existing GI tubing & connections complete all as specified and directed by Engineer-in-charge.

M&L for Cutting chases, of girth not exceeding 10 cm for concealed water tubing or concealed conduit wiring, etc. in stone / brick masonry wall built in cement mortar and making good, disturbed surface in Cement mortar 1:3 complete all as specified and directed by Engineer-in-charge.

Taking down eaves gutters and rainwater pipes (any type or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories complete all as specified and directed by Engineer-in-charge.

S & F PVC (SWR) 110 mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engineer-in-charge.

S & F PVC (SWR) 110 mm bore pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer-in-charge.

S & F in epair PVC (SWR) 110mm bends any radius complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC (SWR) vent cowl 110mm dia complete all as specified and directed by Engineer-in-charge.

S & F in repair 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC (SWR) 110mm dia in junction single, (Single T) equal or unequal complete all as specified and directed by Engineer-in-charge.

S & F in repair stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays for fixing 110mm dia PVC pipe, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed by Engineer-in-charge.

S & F in repair PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer-in-charge.

S & F in repair PVC (SWR) 75 mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engineer-in-charge.

S & F in repair PVC (SWR) 75mm bends any radius complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC (SWR) 75mm dia in junction single, (Single T) equal or unequal complete all as specified and directed by Engineer-in-charge.

S & F in repair PVC (SWR) branch piece 75mm, single (single Y) equal or unequal with access door bend complete all as specified and directed by Engineer-in-charge.

S & F in repair PVC (SWR) multi floor trap 75 mm with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-charge.

S & F in repair stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays for fixing 75mm dia PVC pipe, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed by Engineer-in-charge.

S&F in repair European type water closet including CI P/S trap as directed including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc.,with flush pipe PVC 32mm dia and incl. plastic seat cover as recommended by manufacturer closed pattern with flat bottom etc; and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and including supply and fix of PVC long arm P/S trap so that joint is avoided inside the building as well as in wall and outlet straight away come out of wall in all floors G.F.and taking down existing of any description/size complete all as specified and directed by Engineer-in-charge.

S & F in repair Vitreous china premium/1st quality wash down water closet Size: 360x640x685 mm, Single Piece-WC with PP soft close seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern fittings, S Trap-220 mm complete all as specified and directed by Engineer-in-charge. Make: (Jaquar) Cat No.SLS-WHT-6851S220PP or equivalent make mentioned in Appendix 'C'.

S&F in repair plastic EWC seat cover, coloured closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device complete all as specified and directed by Engineer-in-charge.

S&F Flushing cistern of PVC 10 ltr. cap. with single flushing system, valveless syphonic action type, , low level, white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete all as specified and directed by Engineer-in-charge.

Supply only PVC syphon complete for low level flushing cistern complete all as specified and directed by Engineer-in-charge.

S&F in repairs 15 mm size wall mixer with Provision For Overhead Shower with 115mm Long Bend Pipe On Upper Side, Connecting Legs & Wall Flanges for iron pipe complete all as specified and directed by Engineer-in-charge. Make: (Jaquar) Cat No.CON-273KNUPR or equivalent make mentioned in Appendix 'C'.

S&F in repairs 15 mm size Central Hole Basin Mixer without Popup Waste System with 450mm Long Braided Hoses screwed for iron pipe complete all as specified and directed by Engineer-in-charge. Make: (Jaquar) Cat No.CON-167KNB or equivalent make mentioned in Appendix 'C'

S&F in repair 15 mm Pillar cock rocket type with aerator with chromoum plated, suitable for 15mm bore pipe line complete all as specified and directed by Engineer-in-charge. Make: (JAQUAR) Cat No- CON-011KN or equivalent make mentioned in Appendix 'C'

S&F in repair 15 mm Pillar cock Auto closing system type with chromoum plated, suitable for 15mm bore pipe line complete all as specified and directed by Engineer-in-charge. Make: (JAQUAR) Cat No- PRS - 031 or equivalent make mentioned in Appendix 'C'

S&F in repair 15 mm size bib tap long body with wall flange , chromium plated, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge. Make: Cat No : CON-107KN (JAQUAR) or equivalent make mentioned in Appendix 'C'

S&F in repair 15 mm size Basin inlet connection (Angular stop cock) with wall flange, chromium plated complete all as specified and directed by Engineer-in-charge. Make : Cat No (JAQUAR) CON-059KN or equivalent make mentioned in Appendix 'C'

S&F in repair 15 mm concealed stop valve with Exposed Part Kit of Concealed StopCock with Fitting Sleeve, Operating Lever & Adjustable Wall Flange (Compatible with ALD-083FT & ALD-089FT), chromoum plated, with regular body of suitable for 15mm bore pipe line complete all as specified and directed by Engineer-in-charge. Make : Cat No (JAQUAR) Cat No.CON-083FTK or equivalent make mentioned in Appendix 'C'

S&F in repair Grab Bar 300mm Long, Stainless Steel complete all as specified and directed by Engineer-in-charge. Make : (Jaquar ) cat No AKP-35701PS equivalent series in KOHLER/Roca

S&F in repair 15 mm size bib tap long body, fancy type chromium plated, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge.

S&F in repair 20 mm size bib tap long body, fancy type chromium plated, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge.

S&F in repair 15mm bore stop cock cast copper alloy, fancy type, chromium plated, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed complete all as specified and directed by Engineer-in-charge.

Supply and fix in repair 15mm bore fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-charge.

Supply and fix in repair 20mm bore fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-charge.

S & F in repair for 125mm size Brass chromium plated shower rose with or without swivel joints, any size complete all as specified and directed by Engineer-in-charge.

S&F in repair 20mm dia brass chromium plated towel rail complete all as specified and directed by Engineer-in-charge.

S & F in repair SS Soap dish, embedded in the wall complete all as specified and directed by Engineer-in-charge.

S &F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in positioncomplete all as specified and directed by Engineer-in-charge.

S & F in repair for PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed by Engineer-in-charge.

S & F in repair for PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed by Engineer-in-charge.

S & F in repair Grating doom 100 mm dia of PTMT (minimum weight 25gms) complete all as specified and directed by Engineer-in-charge.

S & F in repair stainless steel grating 100x100 mm size square / rounded 100 mm dia with or without hole as per required shaped for floor trap fixed in position complete all as specified and directed by Engineer-in-charge.

S&F in repair Vitreous china premium/1st quality wash hand basin white, Size: 560x415x200 mm including all accessories as recommended by manufacturers instructioninstructions and fixed in positions and including all Waste fittings, brass,chromium plated complete all as specified and directed by Engineer-in-charge. Make: Jaquar . Cat part No: CNS-WHT-801or equivalent make mentioned in Appendix 'C'

S & F in repair Vitreous china premium/1st quality wash basin (under counter), white, size 550x400 mm including S&F all accessories as recommended by manufacturer complete fixed in position in all respect as per manufacturer's instructions and all as specified including all Waste fittings, brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-charge. Note : The items for counter will be measured and paid separately.

S&F in repair vitreous china squatting pan orissa pattern complete of size 580 x 440 mm white with intagral foot rest and making good to the floor complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repairs PVC Flexible waste pipe 32/40 mm dia having length 900mm with socket for steel sink/WHB/ urinal upto floor level complete all as specified and directed by Engineer-in-charge.

S & F in repair Vitreous china premium/1st quality urinal (Top inlet), with Fixing Accessories, Size: 475x315x715 mm as recommended by manufacturers instructions complete all as specified and directed by Engineer-in-charge. Make: Jaquar . Cat part No: URS-WHT-13259 or equivalent make mentioned in Appendix 'C'

S & F in repair Vitreous china premium/1st quality urinal pedestal type of white colour, of size 355x340x535mm incl providing and fixing plugs/brackets, bedding urinal against wall in CM 1:2, securing urinals to plugs with and incl S&F of all accessories for fixing as recommended by manufacturer like 60mm long brass secrews/fasteners/rag bolts etc, pointing urinal back in white cement; connecting for discharge pipe incl necessary packing, union complete all as specified and directed by Engineer-in-charge. Make: Jaquar . Cat part No: URS-WHT-13261or equivalent make mentioned in Appendix 'C'

S&F in repair CP Brass Urinal spreader for fixing with 15mm dia pipe. complete all as specified and directed by Engineer-in-charge.

Supply & Fixing in repair Corner glass shelf size 300 mm radius with and including bracket and glass complete set etc complete all as specified and directed by Engineer-in-charge.

Supply & Fixing in repair Glass shelf size 600 mm long with and including bracket and glass complete all as specified and directed by Engineer-in-charge.

S&F in repair stainless steel sink, made out of 1.00mm thick sheet for kitchen or laboratory with plug,washers, waste pipe, cast irn cantilever bracket of 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-charge.

S&F in repair stainless steel sink with drainage board , made out of 1.00mm thick sheet for kitchen or laboratory with plug,washers, waste pipe, cast irn cantilever bracket of overall size 915x460mm bowl size 410x330x160mm complete all as specified and directed by Engineer-in-charge.

S & F in repair 32mm size Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm45gms/40mm-60 gms) complete all as specified and directed by Engineer-in-charge.

S & F in repair 40mm size Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm45gms/40mm-60 gms) complete all as specified and directed by Engineer-in-charge.

S & F in repair 20mm size GI nipple suitable for HDPE water tank (minimum weight 25-65gm) complete all as specified and directed by Engineer-in-charge.

S & F in repair 25mm size GI nipple suitable for HDPE water tank (minimum weight 25-65gm) complete all as specified and directed by Engineer-in-charge.

Taking down chowkats or frames exc 1.5 sqm but n.exc 4sqm each with shutters (without taking off shutters from the frame), complete all as specified and directed by Engineer-in-charge.

Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and directed by Engineer-in-charge.

Taking down shutters of any description exc 1sqm but not exc 2.00 sqm each complete all as specified and directed by Engineer-in-charge.

Taking down shutters of any description exc 2.00sqm each complete all as specified and directed by Engineer-in-charge.

Resecuring or easing & adjusting without taking down the shutter of any description exc 1 Sam and n.exc 2 Sqm in same opening complete all as specified and directed by Engineer-in-charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made.

S & F Pressed steel frames for doors of size 105mmx60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed by Engineer-in-charge.

S & F Factory made ISI marked flush door shutters 35mm thick, BWP conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 2nd class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters complete all as specified and directed by Engineer-in-charge and including supply and fixing following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm - 1 No per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf

S & F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-I section 8 clause 8.20 (a) kiln seasoned and chemically pressure treated all as specifeid including stainless steel 304 grade wire cloth ( 0.36mm nominal dia of wire and average width of aperture 1.40 mm ) complete all as specified and directed by Engineer-in-charge and including supply and fixing following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x3000mm - 1 nos per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf

S & F 30mm thick Factory made single extruded WPC (Wood PolymerComposite) solid plain flush door shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge and incl supply and fixing following items:- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf

S & F 300mm, mild steel, ordinary rat tail rod pattern springs including roller and roller plate, bearing ISI mark complete including necessary welding work complete all as specified and directed by Engineer-in-charge.

M & L for preparation of new or previously untreated steel surfaces including two coat of synthetic enamel (ordinary tint) paint over priming with red oxide,zinc of any description, over 10cm in width or girth, not otherwise described complete all as specified and directed by Engineer-in-charge.

M & L for preparation of new wooden surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint, first quality, over a coat of pink primer complete all as specified and directed by Engineer-in-charge.

S&F Powder coated 50 microns extruded aluminium glazing/ doors & shutters made out of section 63.5x38.10x1.20mm for chowkats or frame & shutters made of size 44.45x44.45x1.29mm for side rails and middle rail, 114.3X44.45X1.29mm for top rails and bottom rails and including 12mm thick High Density Fibre Board pre-laminated on both sides (water proof) below middle/lock rail and 5mm thick tinted glass above middle/lock rail and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beads 20mm size with and incl mortice lock with duplicate keys etc incl taking down of frame and shutter in any type/size complete all as specified and directed including supply and fixing the following items: (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 3 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 200mm long - 2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf

S&F Providing and fixing factory made aluminium casement windows with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60 x 44.45 x 1.29 mm and shutters made of 63.5 x 31.75 x 1.29 mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36 mm dia and 1.40 mm aperature in inner shutters including taking down of frame and shutter in any type/size complete all as specified.complete fixed in all respect as specified including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 2 nos per leaf (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf

S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, including removal of existing grill complete all as specified and directed by Engineer-in-charge.

S&F steel rolling shutters, 1.00mm thickness of laths with out ball bearing, but gear operated type with bevel gear box and crank handle as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, including taking down existing unserviceable rolling shuttercomplete all as specified and directed by Engineer-in-charge.

S&F Powder coated 50 microns extruded aluminium frame for fixed type partition (Standard two panel pattern) made out of powder coated aluminium section of size 63.5 x 38.10 x 1.5mm, comprising of 5mm thick tinted glass inserted in and including necesary jointing cleats, rubber packing, anodised aluminium snap beading complete fixed to floor and wall by means of cadium plated steel screws complete incl taking down of existing partition with all fittings and fixtures complete all as specified and directed by Engineer-in-charge.

S&F in repair door closer hydraulically regulated designation No 3 universal type suitable for door shutter 851mm to 1000mm vide and weight between 61 to 80 kg of aluminium (extruded section body) complete all as specified and directed by Engineer-in-charge.

S & F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engineer-in-charge.

S&F in repair 100mm size MS butt hinges medium weight cold rolled including necessary screws, ISI marked complete all as specified and directed by Engineer-in-charge.

S&F in repair 75mm size MS butt hinges medium weight cold rolled including necessary screws, ISI marked complete all as specified and directed by Engineer-in-charge.

S&F in repair 200mm long aluminium anodised barrel tower bolt ISI marked complete all as specified and directed by Engineer-in-charge.

S&F in repair 150mm long aluminium anodised barrel tower bolt ISI marked complete all as specified and directed by Engineer-in-charge.

S&F in repair 150mm long aluminium handle cast type anodised ISI marked complete all as specified and directed by Engineer-in-charge.

S&F in repair 100mm long aluminium handle cast type anodised ISI marked complete all as specified and directed by Engineer-in-charge.

S&F in repair 250mm x 16mm dia aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of steel cast or extruded section or cast aluminium alloy ISI marked complete all as specified and directed by Engineer-in-charge.

S&F in repair 140 mm over all length of cover plate of floor door stopper, bearing ISI mark, of aluminium alloy body and tongue, anodised with hard drawn steel spring, complete all as specified and directed by Engineer-in-charge.

S&F in repair 300mm, mild steel, ordinary rat tail rod pattern springs including roller and roller plate, bearing ISI mark complete including necessary welding work complete all as specified and directed by Engineer-in-charge.

S&F in repair 65mm size Grade I, dual Lever Brass lock for cup board/doors complete all as specified and directed by Engineer-in-charge.

Dismantling wall and ceiling boarding of any description, thickness including cover fillets complete all as specified and directed by Engineer-in-charge.

M&L for providing and fixing Gypsum Board 10mm thick in ceiling as desired nshape fixed with screw as per manufacturers instructions complete all as specified and directed by Engineer-in-charge.

M&L for Exposed metal frame ceiling with 6mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid (Frame work for ceiling shall be measured and paid separately) complete all as specified and directed by Engineer-in-charge.

S & F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed by Engineer-in-charge.

M&L for anlodised aluminium snap grid frame work for false ceiling complete all as specified and directed by Engineer-in-charge.

M& L for two coat of Oil bound distemper on ceiling surface including prepration of new surface complete all as specified and directed by Engineer-in-charge.

S&F hollow PVC Wall panelling consisting of 5mm thick decorative colour PVC sheet inclusive of fixing at site on aluminium frame as per specifications and drawing including supply and fixing of all accessories like fastners/screws /solvents/ beadings etc complete all as specified and directed by Engineer-in-charge.

S&F in repair stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixedd with tinned tacks or stainless steel wire staples or with wooden beads, stainless steel screws and nuts bolts etc complete all as specified and directed by Engineer-in-charge.

S & F 3mm thick sheet glass ordinary quality & glazing with oil putty or fitted with wooden/steel beads in squares n.exc. 0.50 sqm in each pane with puty or fixed with wooden bends including hacking out old broken glass from wooden/metal frame complete all as specified and directed by Engineer-in-charge.

S&F 3 mm thick frosted on one side sheet glass ordinary quality & glazing with oil putty or fitted with beads in squares n.exc. 0.50 sqm in each pane including hacking out old broken glass with puty or fixed with wooden bends complete all as specified and directed by Engineer-in-charge.

S&F, 4.8mm thick, sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each panes and including hacking out old broken glass panes (any thickness size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed by Engineer-in-charge. Note :- To be fixed at any floor level not more than triple storey.

S & F in repair stainless tubing of 25mm dia chromium plated min 1.00mm wall thickness as in curton rod and including 02 Nos stainless steel brackets/finials fancy type , stops fixed with SS screws etc complete all as specified and directed by Engineer-in-charge.. Note : For the purpose of measurement and payment running length of curtain rod and only shall be considered.

S&F 10mm thick toughned glass as in frameless doors, partitions automatic doors and similar works including floor door springs double action fixed in top and bottom, including cutting to shape, drilling holes, beads with all acessories like handle, stopper with glazing with beads fixed with metal panel pins as required including hacking out glass complete all as specified and directed by Engineer-in-charge.

S&F for 3mm thick (of any finish) aluminium composite panels (ACPs) for construction of external facades, cladding, signage, fixed on wall/ceiling, cutting/bending to desired shapes, drilling holes, beads with all acessories as required including taking down the existing panels if any complete all as specified and directed by Engineer-in-charge.

M&L for taking down carefully existing aluminium/ copper point wiring (light, fan, socket or power) complete fittings fixture such as switches Ceiling roses, pendents,regulators, sockets etc to be measured separately)unscrewing from Board/outlet boxes, fittings & fixtures such as switches, sockets, ceiling rose lamp holder tube/ceiling fitting, bulk head fittings, tube lights & regulator etc and making good disturbed surfaces of walls, floors etc. complete all as specified and directed by Engineer-in-charge.

M&L for taking down carefully existing old DBs and making good disturbed surfaces of walls to match the existing surfaces complete all as specified and directed by Engineer-in-charge.

M&L for taking down unserviceable submain wiring alongwith batten/PVC/steel conduits etc and making good disturbed surfaces of walls/ floors to match the existing surfaces complete all as specified and directed by Engineer-in-charge.

M&L for point wiring (modular type) with two run of PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm (FRLSH), PVC conduit medium grade/ PVC casing caping and pressed steel terminal boxes (for mounting switches /sockets/ regulators/ceiling roses etc) and drawing one run of 1.5 sqmm PVC insulated unsheathed multistranded copper conductor cable (FRLSH) as earth continuity wire in green colour connected to common earth and each terminal box/fitting all as specified and as directed by Engr-in-Charge. Note : Modular switch and socket shall be measured and paid separately. (In ceiling Portion surface conduit wiring shall be carried out.) Note: The quoted rate inclusive for the following :- (a) GI metal flush box and Modular cover plate with frame of any module complete. (b) Proper colour coding is to be followed as per IS Specification. (c) wiring shall be concealed/ on surface with rigid PVC conduit medium grade/PVC casing caping as per site requirement. (d) Cutting chases/making good disturbed surfaces of wall for fixing concealed conduit wherever required will be measured and paid separately.

One light point controlled by one one way switch.

One fan point controlled by one one way switch.

One 3 pin socket outlet 5/6 Amps independent.

One 3 pin socket outlet 5 Amps on the same board with other switches

One light point controlled by two 2-way switches.

One bell/ buzzer point controlled by one push button

All as per item No 150.00 above but cable with 4.0 sqmm size for socket outlet 15 amps, independent.

M & L for submain wiring with two single core PVC insulated unsheathed multistranded copper conductor cable of size 6 sqmm (FRLSH) and one single core PVC insulated unsheathed multistranded copper conductor cable green colour of size 6 Sqmm (FRLSH) as earth lead in and including concealed with PVC conduit medium grade of suitable size or surface wiring with PVC casing caping of suitable size and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed by Engineer-in-charge. Note : (i) Three run of cable with one run of PVC conduit/PVC casing and caping will be measured as one length. (ii) Wiring shall be concealed/ on surface with rigid PVC conduit medium grade/PVC casing caping as per site requirement. (iii) Cutting chases/making good disturbed surfaces of wall for fixing concealed conduit wherever required will be measured and paid separately.

All as per item No. 152.00 here-in-before but with 4.0 sqmm cable complete all as specified and directed by Engineer-in-charge.

All as per item No. 152.00 here-in-before but with 2.5 sqmm cable complete all as specified and directed by Engineer-in-charge.

All as per item No. 152.00 here-in-before but with 1.5 sqmm cable complete all as specified and directed by Engineer-in-charge.

S&F ceiling Rose, 3 terminal polycarbonate isolated body complete all as specified and directed by Engineer-in-charge.

S&F modular switch one way 6 Amps, 1 module complete all as specified and directed by Engineer-in-charge.

S&F modular switch two way 6 Amps, 1 module complete all as specified and directed by Engineer-in-charge.

S&F modular switch one way 16 Amps, 1 module complete all as specified and directed by Engineer-in-charge.

S&F modular bell push 6 Amps, 1 module complete all as specified and directed by Engineer-in-charge.

S&F modular socket, 2/3 pin 6 amps, 2 module complete all as specified and directed by Engineer-in-charge.

S&F modular socket, 2/3 pin 6/16 amps, 2 module complete all as specified and directed by Engineer-in-charge.

Supply and fixing of LED box type Integrated Batten Wattage 20 watt having Aluminum Extruded housing in white powder coated Finish with high translucent PC Cover, Dimension of the Fixture Must not be less Then Length 1170 MM (± 5 MM ), Elegant Design, IP 20 Protection. Minimum Lumens output of the fitting shall be 2500 Lumens With Efficacy of 125 lm/W, CCT 5700 – 6500K, Surge Protector 4 KV, PF>= 0.95 , Necessary mounting arrangements. The Manufacturer of the fixture shall have in house NABL Accredited Lab and must produce certificate of the same along with LM-79 / LM-80 / Test Report complete all as specified and directed by Engineer-in-charge.

S&F as in repair LED 20W inverter batten type fitting 3/4 feet long aluminium extruded housing, charging time 10-12 Hrs with 04 Hrs backup,IP-20 ,rated voltage 230 V, 50 Hz, system wattage 20W +/- 10%, system current less than 102 mA, power factor more than 0.95, system lumen efficiency 100lm/watt,CCT 6500K, CRI more than 80, THD less than 30%, driver efficiency more than 85% complete all accessories prewired and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engineer-in-charge.

S & F for LED tube light fitting 10 Watt, 2 Feet or 591 MM in length, IP 20 Protection, wall mounted type, Slim LED Batten with extruded aluminium housing and polycarbonate diffuser, elegant design with end caps, having excellent thermally managed polycarbonate extrution, LM 80 Certified LED having Integral Electronic Constant Current Driver, IP 20 Protection, Opreating voltage 240 V, 50Hz AC Supply and Operating tempraeture 0 to 50 C, Power factor ≥ 0.9, Lumen output ≥ 1000, necessary mounting arrangements on PVC Square box 2 Nos, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white color flexible pipe complete all as specified and directed by Engineer-in-charge.

S & F in repair for LED down lightrecess mounted/Surface mounted/POP mounted or as per site requirement, square/Round type worm white / Neutral white or 2700 K- 3000 K as per user requirement 18 watts with efficiency of 100 lumens per watt, in worm white/ neutral white as per site requirement sleek design aluminium housing polycarbonate diffuser white finish operating voltage from ceiling rose to fitting complete all as specified and directed by Engineer-in-charge.

Supply and fixing of recessed/ceiling mounted down lighter with CRCA housing with high bright LED,idealy suited for low ceiling areas Brilliance 36watt LED, size 2ft x 2ft The product features color tuning from CCT 3000K – 6000 k, Surge Protector 4 KV, PF>= 0.95 , necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white color flexible pipe complete all as specified and directed by Engineer-in-charge.

S & F in repair recess mounted/Surface mounted/POP mounted or as per site requirement LED down light 06 Watt round/Square in shape worm white or 2700 K- 6000 K as per user requirement Ideal for wardobes, furniture lighting, display & interior decoration complete all as specified and directed by Engineer-in-charge.

Note for item No 163 to 168 : (i) Driver efficiency more than 85% (Constant current driver) (ii) Non isolated type driver (iii) THD less than 20% (iv) LED driver current less than 60 mA (v) Efficiency of LED Chip more than 130 lm/watt (vi) Efficiency of LED Fixture 100 lm/watt (vii) Surge protection 2.0 KV & above as per IEC standard (viii) working humidity 95%RH (ix) Life 50000 Hrs at 70% lumes (x) CRI more than 80 (xi) Working temp -10 degree to 50 degree C (xii) Heat Sink extruded aluminum (xiii) junction temperature 85 degree C (xiv) Body of fitting Extruded Aluminum (xv) impact code Min IK 03 or more ( xvi) LM79 report from thir party (instead of company in house lab) NABL/UL accredited lab (xvii) LM 80 report from LED manufacturer (xviii) Low/High voltage, reverse polarity, overload and short circuit protection inbuilt in fixture (xviiii) IP-20 .(xx) Test certificates to be submitted before commencement of work/ claiming for payment .(xxi) Warranty certificate for minimum 2 years to be submitted from OEM.

S&F in repair LED bulb 9 watt, warm white B22 complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repair LED inverter bulb 12 Watt, CDL, 220V AC complete all as specified and directed by Engineer-in-charge.

S&F in repair lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by Engineer-in-charge.

S&F in repair Bell, Ding Dong AC, 230 Volts complete all as specified and directed by Engineer-in-charge.

Supply and fixing in repair MCCB DB VTPN 4 way IP-54, IK-09 made of sheet steel phos phatised, powder painted with suitable rated bus bar as per OEM design, neutral link, earth bar and Din rail 415 Volts with double door, suitable for MCCB 4 Pole 100 Amps as incomer and MCB Single Pole as outgoing complete all as specified and directed by Engineer-in-charge.

Supply & fixing in repair sheet metal enclosure with TPN MCB DB's 4 way (grouted in walls) double door type IP-54, IK-09 Protection. Isolated Neutral, Door earthing, with suitable rated bus bar as per OEM design including suitable size of copper ferrules for fixing of cable complete all as specified and directed by Engineer-in-charge.

Supply & fixing in repair MCB DB's SPN 4 way, IP-54, IK-09 double door, sheet metal enclosure, 240V, with suitable rated bus bar as per OEM design including suitable size of copper ferrules for fixing of cable complete all as specified and directed by Engineer-in-charge.

Supply & fixing as in repair MCB DB's SPN 8 way, IP-54, IK-09 double door, sheet metal enclosure, 240V, with suitable rated bus bar as per OEM design including suitable size of copper ferrules for fixing of cable complete all as specified and directed by Engineer-in-charge. Note for item srl No 174 to 177 : (i) MCCB and MCB will be measured and paid separately. (ii) The cost for flushing of Distribution box in any type of wall and making good disturbed surfaces with existing colour shall be deemed to be included in the quoted rate

Supply and fixing in repair Single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and directed by Engineer-in-charge.

S&F in repair MCCB 4 Pole, 415V, Adjustable type, 100 to 125 Amps with breaking capacity 16 KA complete all as specified and directed by Engineer-in-charge.

S&F in repair MCB TPN 40 to 63 Amp, C series, 415V, 10 KA complete all as specified and directed by Engineer-in-charge.

S&F in repair RCBO 25-40 Amps, double pole 240V, AC type, 30 mA complete all as specified and directed by Engineer-in-charge.

S&F in repair MCB SP 6-32 Amps ,10 KA, B Curve, 230 Volts ,50 HZ complete all as specified and directed by Engineer-in-charge.

S&F in repair Surge Protection Device, breaking capacity 40KA/Pole, 4 Pole with sheet metal enclosure complete all as specified and directed by Engineer-in-charge.

Supply and fixing Thermoplastic/ Polycarbonate/ sealed moulded meter box, IP-43, weather proof & water proof single door with locking arrangement, transparent meter viewing window glass suitable for smart single phase meter complete all as specified and directed by Engineer-in-charge.

M&L for cutting chases in concrete block walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed PVC Conduit etc., and making good, cutting not exceeding 10 cm girth etc., including making good disturbed surfaces with existing wall colour complete all as specified and directed by Engineer-in-charge.

M&L for carrying out internal wiring test with all T&P such as megger, clamp meter/multi meter etc., by opening of main DBs/TPN DBs/SPN DBs disconnecting of phase and neutral cable connection, fittings, fixtures carrying out testing for insulation values, reconnecting the disconnected cable connections, fittings and fixtures including replacement of defective copper ferrules, insulation peeled off wires with insulation tape complete all as specified and directed by Engineer-in-charge. Note : (i) The cost of copper ferrules and insulation tape shall be deemed to be included in the quoted rate. (i). The inspection shall be carried out in presence of JE E/M, I/C Elect(HS)/MCM detailed by JE E/M with user's signature. (ii) Each Building will be measured as one job.

S&F Ceiling fan downrod suitable size upto 03 feet with GI Hook as per requirement of site of any size including takind down & refixing of ceiling fan complete all as specified and directed by Engineer-in-charge.

M/S MAYA CONSTRUCTION COMPANY (BID ID -3470039)

M/s Shri Inder Construction Company (BID ID -3465676)

M/S R.K. Builders & Developer (BID ID -3470430)