SPECIAL REPAIR TO BLDG NO P-64 AT BD BARI UNDER GE KALUCHAK

Amount

B&R PORTION:- Demolition of brick work or stone/ boulder masonary built in cement mortar including all quoins arches pillars etc complete all as specified & directed.

Brick work in cement mortar 1:6, using sub class ‘B’ bricks, straight or curved on plan exc. 6m mean radius complete all as specified & directed.

Description all as per item No.2 above, but except bricks, complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified & directed.

Rendering 15 mm thick plaster in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth with out using extra cement, complete all as specified & directed.

Rendering 15 mm thick plaster in cement mortar 1: 6 on fair faces of brick work or concrete surfaces, finished even and smooth with out using extra cement, complete all as specified & directed.

Rendering 10 mm thick plaster in cement mortar 1: 3 on concrete surfaces as in ceilings finished even and smooth without using extra cement, complete all as specified.

Taking down cement plaster and decayed concrete of any description, upto double storey of building, from roof projection, chajjas etc and making good the decayed portion with cement mortar 1:3 mixed with water proofing compound or PCC 1:2:4 type B-0 (using 12.5mm graded aggregate) including necessary form work where ever required and finally finishing the surface with 15 mm thick cement plaster in CM 1:3 and applying two coats of exterior emulsion paint to match the existing surface /finish, complete all as specified and as directed.

Preparation of newly plastered surfaces of wall and applying two coats distemper oil emulsion over & including a coat of wall care putty 3mm thick, complete all as specified and directed.

Preparation of newly plastered surfaces of wall and applying two coats of cement base paint over & including a coat of primer, complete all as specified and directed.

Preparation of newly plastered surfaces and applying two coats of white wash on ceilings, complete all as specified.

Coloured joint free non skid ceramic tiles 400 x 400 x 7 to 8 mm thick in floors laid over and including 15 mm thick screed bed or bedding layer of cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles complete, all as specified and directed.

Coloured glazed ceramic tiles 400 x 400 x 7 to 8 mm thick on vertical surfaces of walls including 10mm thick backing coat of cement mortar 1:4 as in dado, skirting, riser of steps etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles complete, all as specified and directed.

Vitrified tiles, light shade 600 x 600 x 9 to 10 mm thick, polished in floors laid over and including 15 mm thick screed bed or bedding layer of cement mortar 1:4, set and jointed in neat cement slurry and pointed in white cement to match the colour of tiles, all as specified.

Vitrified tiles, light shade 600 x 600 x 9 to 10 mm thick, polished on vertical surfaces of walls including 10mm thick backing coat of cement mortar 1:4 as in dado, skirting, riser of steps etc., set and jointed in neat cement slurry and pointed in white cement to match the colour of tiles, all as specified.

Coloured glazed ceramic tiles 450mm x 300mm x 7mm thick on vertical surfaces of walls laid over and including 10 mm thick backing coat of cement mortar 1:4 as in dado, skirting, riser of steps etc., set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles, all as specified.

18-20mm thick black Granite stone machine cut laid over and including 15 mm thick screed bed or bedding layer of cement mortar 1:4, jointed in grey cement with admixture of pigment to match the shade of granite stone including cutting, polishing and half rounding of exposed edge of stone complete, all as specified and directed.

Machine cut Kota stone slab flooring not less than 19mm thick laid over and including 20 mm thick screed bed or bedding layer of cement mortar 1:4, jointed in grey cement with admixture of pigment to match the shade of slab including cutting, mirror polishing and half rounding of exposed edge of stone complete, all as specified and directed.

Machine cut Kota stone slab not less than 19mm thick (as per sample kept in GE's office) in tread and riser of steps, skirting, dado laid over and including 15 mm thick backing coat of cement mortar 1:4 jointed in grey cement with admixture of pigment to match the shade of slab including cutting, mirror polishing and half rounding of exposed edge of stone complete, all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), terrazzo toping and rubbish off the premises all as specified and directed.

25 mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crushed stone agg) as in floor etc surface finished even & smooth without using extra cement, complete all as specified and directed.

100mm thick Plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base, complete all as specified and directed.

75mm thick plain cement concrete 1:3:6 type C-2, using 20mm graded stone aggregate as in plinth protection complete al as specified and finishing the surface even and smooth without using extra cement, complete all as specified and directed.

Demolition of (un reinforced) cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5 sqm & n.exc. 4 sqm each all as specified and directed

Taking down chowkats or frames with shutters (without taking off shutter from the frames) n.exc 1.50 Sqm each all as specified and as directed.

30mm thick, flush shutters, soild core construction, with block board core and plywood face panels commerical type both faces is covered with decorative face veneer with lipping/frame to match and complete all as specified & directed.

Factory made 35mm thick Plain framed, panelled shutter (two panel) of second class hard wood,with lock rail and panel of 9 mm thick B.W.P. commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, all as specified.

Factory made glazed and skeleton shutters 35mm thick, of second class hard wood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats, all as specified.

Box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick MS sheet tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire cloth and glass panes will be measured and paid seperately) with side hung shutters with MS handles and MS peg stay dovetailed or welded incl 02 Nos, MS Tower bolts 150 mm long for each leaf and 08 mm square bar grill / guard bars at spacing as shown on Drg welded to MS flat iron frame work ,including other fittings ,hinges ,MS handles ,tarred hold fasts ,PCC blocks for hold fasts etc all as shown on Drg No CEPZ/TD -354/09 sheet 1/3 to 3/3 including one coat of of red oxide zinc primer, complete all as specified and directed by Engr-in-charge.

Factory made solid core PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

2nd class hard wood plain solid straight chowkats wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints etc, complete all as specified.

Aluminium anodized frame of size 124.60mm x 44.45mm made out of 1.60mm thick aluminium section, powder coated, fixed to floor wall with plugs and screws complete all as specified and directed.

Aluminium anodised powder coated window/ventilator shutter, section of size 44.45 x 44.45mm made out of 1.6mm thick aluminium sheet/section including necessary jointing cleats, glazing clips, rubber packing, suitable handle 1 No's in each shutter, tower bolt, hinges 110mm long, anodised aluminium snap beading screws, complete all as specified and directed. Note : Sheet glass to be fitted will be measured and paid separately.

Aluminum anodized powder coated grill fixed in windows complete all as specified and directed. Note : Thickness and type of grill shall be approved by GE.

Aluminum anodized powder coated channel any section fixed in windows grill complete all as specified and directed

5mm thick tinted glass as in aluminium door and window with aluminium hollow beading/glazing clip size 19mm x 17mm made out of 0.70mm thick hollow section weighing not less than 0.97 Kgs/RM including rubber gasket, complete all as specified and directed.

Wire cloth stainless steel 0.45mm nominal dia of wire and average width of aperture 2.0mm and fixed with wooden beadings or with screws to aliminium windows or fixed with nut bolts to steel windows, complete all as specified and as directed.

19mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work and in moudular kitchen etc, complete all as specified and directed.

12mm thick Plywood grade BWR type BB, fixed with screws/nails as in kitchen shelves, drawers, built in furniters and like works cupboards, pelmet boxes etc, complete all as specified and directed.

40 mm wide flaps Continuous (piano) hinges , mild steel bright finish or electrogalvanised as in cup boards, kitchen cabinat etc, complete all as specified and as directed by Engr. In Charge.

Ball catches with 8mm dia steel ball, and brass body and stricking plate including letting, complete all as specified and directed.

40mm dia , Cupboard knobs fixed with nut , screw and washer of mild steel , bright finished, complete all as specified and directed.

Hasp and staple 75mm safety type aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed.

Aluminium handles cast type, anodised, 150mm size, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

Aluminium anodised barrel tower bolts of extruded section with 150 mm long bolt, all as specified.

Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel springs, fixed in floor with over all length of cover plate 150mm, complete all as specified and directed.

Mild steel stove enameled helical door spring 150 mm size fixed to pressed steel frame/MS frame/wooden chowkhats including necessary welding work etc (if required), complete all as specified and directed.

Butt Hinges medium weight cold rolled mild steel of size 100 mm, complete all as specified and directed.

Steel locking bolts of 100 mm size, with mild steel electro galvanised plate and bright bolt not less than 10 mm dia, complete all as specified and directed.

3mm thick plain sheet glass, ordinary quality, and glazing with oil putty or wooden beads, in square n exc. 0.5 Sq m each, complete all as specified and directed.

3 mm thick figured glass, pin head type and glazing with oil putty or wooden beads, in square n exc. 0.5 Sq m each all as specified and directed.

Preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed

Preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed

Dismantling water tanks of any description, capacity exc 250 ltrs and n.exc. 500 ltrs complete, all as specified.

Dismantling water tanks of any description, capacity exc 500 ltrs and n.exc. 1000 ltrs complete, all as specified.

Rotational moulded polyethlene water storage tanks, triple layered, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of Capacity 500 litres including over flow, drain out pipe and all accessories complete, fixed in repairs, all as directed.

Rotational moulded polyethlene water storage tanks , triple layered, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of Capacity 1000 litres including over flow, drain out pipe and all accessories complete, fixed in repairs, all as directed.

Ball brass valve, high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed to pipe 20 mm bore fixed in repairs all as specified.

Stop cock 20 mm cast cooper alloy of screwed down high pressure with crutch or butter fly handle , screwed with ends for iron pipe or unions fixed in repairs. Make ISI marked

Taking up or down 15 mm bore steel tubing and connections including cleaning, threading for refixing or removal to store, all as directed.

Taking up or down 20 mm bore steel tubing and connections including cleaning, threading for refixing or removal to store,complete all as specified & directed.

15 mm bore steel tubing, medium grade, galvanished with all fittings like socket, union, elbow, bend, tees etc and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

Fixing only old steel galvanised tubing of 15 mm bore, with and including all fittings in new or old position as in walls, ceiling, floors etc complete all as specified.

20 mm bore steel tubing, medium grade, galvanished with all fittings like socket, union, elbow, bend, tees etc and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

Fixing only old steel galvanized tubing of 20mm bore, with and including all fittings in new or old position as in walls, ceiling, floors etc,complete all as specified & directed.

Chromium plated angle valve 15 mm of cast copper alloy with crutch handle, screwed down for iron pipe, fixed in repairs, complete all as specified and directed.

Chromium plated stop cock 15 mm of cast copper alloy with long shank and cup (concealed type), screwed down for iron pipe ,fixed in repairs, complete all as specified and directed.

Chromium plated shower rose with swivel joints, 50 mm dia including fixing to steel pipe or union fixed in repairs complete, all as specified and directed all as specified and directed. Make : ESSCO(Jaquar) Cat Part No EOS - 541N or Equivalent make as specified in Appx 'F' here in after.

Brass CP mixer for mixing hot & cold water screwed down for iron pipe, fixed in repairs, complete, all as specified and directed.

Toilet paper holder of brass CP, fixed to walls with chromium plated (CP) brass screws fixed in repairs, complete all as specified and directed.

CP jet spray including CP flexible pipe for EWC fixed, complete all as specified and directed.

CP health fauset including CP flexible pipe for EWC fixed, complete all as specified and directed.

PVC connection 15 mm size, 600 cm long fitted with PTMT nuts with washer on both ends, fixed to 15 mm bore iron pipes, complete all as specified and directed.

PVC bathroom cabinet made out of ABS material of size 45cm x 60cm, complete all as specified and directed.

Vitreous china wash down water closet pan (pedestal pattern) white complete including P or S trap, seat cover and fixing of flushing cistern, brackets, flushing pipe etc fixed in repairs, complete all as specified and directed.

Vitreous china squatting pan 'Orissa' pattern long pan size 580 x440 mm white with integral foot rests (excluding cistern and flush pipe), fixed in repair, complete all as specified and directed.

PVC valve less syphonic action type flushing cistern 10 liters capacity, low level, white with inlet ball valve float and handle including brackets fixed in repairs, complete all as specified and directed.

PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement of 75mm outlet dia, complete all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes of 100mm bore, fixed with walls and taking out of trenches, if required, complete all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes of 75mm bore, fixed with walls and taking out of trenches, if required, complete all as specified and directed.

PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall including fixing clamps complete all as specified.

PVC (SWR) bends any radius 110mm bore, complete all as specified and directed.

PVC (SWR) junction single (single T) equal or unequal 110mm bore, complete all as specified and directed.

PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints fixed to wall including fixing clamps, complete all as specified and directed.

PVC (SWR) bends any radius 75mm bore, complete all as specified and directed.

PVC (SWR) junction single (single T) equal or unequal 75mm bore, complete all as specified and directed.

Tubular towel rail, brass chromium plated, 20 mm dia, D type, 60 cm long between Hangs, fixed in repairs, complete all as specified and directed.

Kitchen sink without drainage board made out of stainless steel sheet 1mm thick with plug washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe over all size 495mm x 420mm,with bowl size 410mm x 330mm x 160mm fixed in repairs, complete all as specified and directed.

Stainless steel plate rack 1200mm x 900mm and 250mm deep made out of 1mm thick stainless steel sheet including shelves etc complete, fixed in repairs, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

Mild steel framed works such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming toFe.290.Gde-E-165 complete all as specified and directed.

Fancy type drapery curtain rod powder coated metalic 20mm dia including MS bracket powder coated, Fibre fancy dome type corner end, rounded block of approved pattern fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and directed.

Complete removal of the existing sunken treatment including roughing and prepration surfaces of old concrete floor by picking , scrubbing down with steel brushes ,sweeping clean and washing down with water to remove dust etc.and applying the following treatment complete all as specified (a) 15mm thick rendering plaster on fair faces of brick work or cement surfaces in cm 1:4 mixed with water proofing admixture by weight of cement to sunken portion including wall of sunken portion with proper slope towards outside and finishing cement concrete or brick work surface even and smooth using extra cement finishing concrete including walls of sunken portion with proper slope all as spd ( (b)Applying Ist course of bitumenous primer @ 0.4 ltr /sqm conforming to IS-3384 over plastered surface. (c)Applying 2nd course of a coat of bonding material with blown type bitumen of grade 85/25 heating to working temperatureand applied @ 1.2 kg/sqm. Contd/-- to Srl item No 96.01

(d)Applying 3rd course of APP (Atactic Polypropylene) modified polymeric 3mm thick weight not less than 3.6 kg/sqm with 160 Grams/sqm non woven polyster made at center core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat . (e)Applying 4th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature and applied @ 1.2 kg/sqm .

Supply only Liquid water proofing liquid admixture, complete all as specified and directed.

Dismantlling of brick tiles or terracing tiles single layer on roof etc, complete all as specified and directed.

PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) with average thickness 25mm as in roof padding, roof kerbs, complete all as specified and directed.

Complete removal of existing roof treatment of any description viz. tarfelt or membrane surface or roof tiles etc. including grubbing up of tree roots and removing all the debris to a distance n.exc 100m and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt / dust etc and applying the following roof treatment complete all as directed:- (a) Applying Ist course of 15 mm thick cement screed in CM 1:4 over concrete surface. (b) Applying 2nd course of bituminious primer confirming to IS-3384 @ 0.4 lit/sqm over the screed bed. (c) Applying 3rd course of a coat of binding material with blown type bitumen of grade 85/25 heating to working temperature of 180 0 C and applied @ 1.2 kg/sqm. Contd/-- to Srl Item No 100.01.

(d) Applying 4th course of APP (Atactic polypropylene) based polymeric membrane minimum weighing 3.6 kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) laid with 75 mm side overlap and 100 mm overlap by forced / torch application as per manufactures instructions. (e) Applying 5th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to working temperature of 180 degree C and applied @ 1.2 kg/sqm over APP membrane, complete all as specified and directed. NOTE :- W P admixture shall be measured and paid separately)

Demolition of (reinforced) cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

Form work to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for rough finished surfaces of concrete, complete all as specified and directed.

TMT bars, 6 to 8mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified.

RCC nominal mix 1:2:4, type, B-0 (using 12.50mm graded crushed stone aggregate), as in slab supported on walls, beams, column etc for kitchen/ bathroom counter for WHB, complete all as specified.

Preparation of old plastered or un plastered surface including brooming down or steel wire brushing, scraping down smoke soot, mould, moss and efflorescent salts and trading oil and greasy spots, and applying one coat of white wash on walls all as specified and directed.

Preparation of old plastered or un plastered surface including brooming down or steel wire brushing, scraping down smoke soot, mould, moss and efflorescent salts and trading oil and greasy spots, and applying one coat of white wash on ceiling all as specified and directed.

Preparation of old distempered and painted surfaces and applying one coat of oil emulsion distemper on walls all as specified and directed.

Complete removing existing treatment and applying two coats of oil bound distemper on walls over a layer of Birla white wall care putty thickness not less than 2mm on walls all as specified and directed .

Preparation of old painted surfaces applying one coat of cement base paint on walls all as specified and directed.

Preparation of old painted wooden surface of any description, over 10 cm in width or girth not other wise described, and applying one coat of synthetic enamel paint, complete all as specified and directed.

Preparation of old painted steel surface of any description, over 10 cm in width or girth not other wise described, and applying one coat of synthetic enamel paint all as specified and directed.

Complete removing existing treatment and applying two coats of weather proof exterior emulsion paint (apex) on projection portions of columns , beams, facia, chajjas , walls , and in small patches all as directed by Engr-in Charge.

Stainless steel baskets for keeping cutlery & packings made of steel wires or sheets all as per design and size approved by GE fixed to drawers or cupboards with sliding channels as per requirements with steel screws as in modular kitchen pattern design, complete all as specified and as directed by Engr-in - Charge.

Brass designer handles 75mm dia size fixed in drawers or shutters as in cupboards, complete all as specified and directed.

Zero crank hinges heavy duty, self closing type as in shutters of cupboars in kitchen, complete all as specified and directed.

Ball rolling sliding channels of size 450mm length fixed in cupboards with screws for holding stainless steel baskets as in drawers, complete all as specified and directed.

Self adhesive tape of 19mm width, hot pressed & pasted on sides & bottom of edges of cupboards shutters, complete all as specified and directed.

Steel fasteners of size 75mm long drilled and fixed to walls, complete all as specified and directed.

50mm dia and 75mm long steel supports fixed with bolt at bottom of cupboards box, complete all as specified and directed.

75 mm thick PCC 1:3:6 type C-1, (using 20mm graded stone aggregate) as in sub-base finished fair, complete all as specified and directed.

Coloured designer chequered cement concrete tile 30cmx30cmx25mm thick with coloured cement and pigment set joint and pointed in neat cement slurry in floor or path etc laid over and including 15mm thick screed bed in cm 1:4 and pointed in coloured cement to match the shade of tile, complete all as specified and directed.

100 mm bore Salt Glazed stone ware drain pipes laid in trenches and jointed, complete all as specified and directed.

PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under, and haunching against the sides of pipes with concrete after they are laid and tested for pipes of 100 mm bore, complete all as specified and directed.

Dismantling and breaking up drain pipes, internal dia of pipe 100 mm (Salt glazed ware, AC or reinforced concrete) set in cement mortar, complete all as specified and directed.

Excavating in trenches not exc 1.5m wide and not exc 1.5 m in deep or foundation etc for shafts, wells,cesspits, man holes, pier holes etc not exceeding 10 sqm on plan and not exceeding 1.5m depth and getting out in any type of soil, complete all as specified and directed.

Returning, Filling in soil including spreading, leveling, watering and well ramming in players not exc 25cm, complete all as specified.

Removal of excavated material to a distance exc 50m not exc 250m and depositing where directed at a level not exceeding 1.5mtr above starting point, complete all as specified and directed.

Solid PVC door / cup board frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening, complete all as specified and directed.

E&M PORTION:- Taking down carefully unsv aluminium / copper conductor point wiring (light, fan, light socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Taking down existing unserviceable distribution board, switch fuse unit, enclosure for MCB / DB (inclusive of MCBs of any type and capacity) and making good the disturbed surface all as specified and as directed.

Taking down carefully sub main wiring of any type and making good distrubed surface of walls and roofs to match the existing surface, complete all as specified and as directed.

Point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLS insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked terminated into CI/pressed steel terminal boxes having wall thickness not less than 1.22mm, including 3.00mm thick laminated sheet cover of hylam brand IS-2036 marked, for mounting switches, sockets, fan regulators etc for one light/fan/exhaust fan/bell point controlled by one, one way switch including cutting chases and making good to disturbed surfaces of wall / ceiling / floor including treating with existing finishes, complete all as specified and as directed.

Description all as per srl item No-132 here in before but for one 3 pin socket outlet 6 amp independent complete all as specified.

Description all as per item No. 132 above but for 3 pin 5 Amps on same board with cable 1.5Sqmm size, all as specified and directed

Description all as per srl item No 132 here in before but for one 3 pin socket outlet 15 Amp independent with cable of size 2.5 Sqmm for main wiring and 2.5 sqmm as in continuous earth wire.

Switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified.

Supply and fixing bell push, flush type 6 amps all as specified and as directed.

Switch socket multipurpose combination 2 in 1, 2 pin & 3 pin, 5 Amp flush type universal,complete all as specifed.

Switch socket multipurpose combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal,complete all as specifed.

Ceiling rose surface bakelite 65mm x 50mm (ISI Marked) 3 terminals PVC/poly carbonate, insulated body, compete all as specified.

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings with and including inverter LED lamp 6500 K, 900 Im in white colour of 9 Watt base cap B-22 with polycarbonate diffuser and aluminium heat sink, complete all as specified and directed.

Supply and fix in replacement Bell multi music type 120 Watt, 240 volt, AC single pole complete all as specified.

Electronic fan regulator two module stepped type with five step 240 volts suitable for 1200/1400 mm sweep AC ceiling fan including taking out the unserviceable complete, all as directed as site

Tube light fitting integrated type slim 20 Watt LED, efficancy 125 lumens / watt, extruded aluminium housing, PC diffuser complete with housing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to light fitting, complete all as specified and directed. Make:-Cromton Greaves Model Bright Linea Cat Part No CCS-100-20-65-HL2-DP-NWH or Equivalent cat part of make as specified in Appx 'F' here in after.

Sub main wiring with single core cable 2x 6 sq mm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including 25mm rigid PVC conduit (Concealed) medium grade alongwith 1x 4 Sq mm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface, complete all as specified and directed. Note:-2 wire of 6sqmm, 1 wire of 4qmm and one run of PVC conduit shall be measured as one unit.

Sheet metal enclosure IP-43, factory made (Double door) for DBs, single pole and neutral, 240 volts, 12 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified. Make:-Legrand Cat part No :-5076 22 or equivalent cat part of make as specified in Appx "F" here in after.

MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series all as specified. Make:- Legrand cat part No-4085 87 to 4085 95 or Equivalent cat part of make as specified in Appx 'F' here in after.

MCB DP, 6 to 32 Amp, 240 volts 50Hz AC supply, complete all specified.

MCB DP-63 Amp, 240 volts 50Hz AC supply, complete all specified.

MCB SPN-63 Amp, 240 volts 50Hz AC supply, complete all specified.

Factory made epoxy powder coated Distribution board vertical TPN 4 ways (TPN MCB DB) with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cale management, top and bottom removable gland plates with Knockouts and suitable for one FP-MCCB as incomer and SP MCBs outgoing complete all as specified and confirming to IS : 8623. (Make:C&S cat no CSDBMCCB100DD04IP43S or equivalent cat part of make as specified in Appx "F" here in after.)

Thermal magnetic release MCCB 415 volts 4 Pole, rating 125 Amps, having short circuit and over load protection, breaking capacity 25 KA , complete all as specified. (Make:C&S cat no CSC1S4125 or equivalent cat part of make as specified in Appx "F" here in after.)

Single pole and neutral enclosure with two pin and earth plug and socket complete with one double pole MCB 20 Amp 240 volts, complete all as specified

Dry river sand cushioning to UG cable 8 cm thick before laying and 15 cm thick after laying complete all as specified and directed. Note:- (a). Dry fine sand of best available quality shall be used. (b). Punned thickness shall be made and paid.

Supply and laying sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

Supply and laying or fixing or passing through pipe 1100 volts grade heavy duty electric cable with XLPE insulated screened PVC bedded aluminium stranded conductor served with inner sheathing of PVC tape armoured with galvanised steel wire or tape and over all PVC sheathed of size 25 Sqmm x 4 core, complete all as specified.

GI pipe medimum grade 40 mm bore for cable protection fixed on poles or laid in trenches, under floor, ducts, road crossing etc with fixing clamps, nuts bolts, washer of requrered size if required, complete all as specified.

Taking up or down steel tubing of 25mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Taking up or down steel tubing of 50mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Steel water tubing of 25 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc laid in trenches, complete all as specified.

Steel water tubing of 50 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc laid in trenches, complete all as specified.

Steel water tubing of 25 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified.

Gun-metal, globe or gate valves for 25 mm pipe, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

Cutting & screwing existing steel tubing of 50mm bore for insertion of Tee 50mmx50mmx50mm including necessary threading / screwing of GI Pipe and TEE required for connection (each cut shall be measured), complete all as specified and directed.

Integral LED security light luminarie 60W LED 230 volts made of pressure die cast aluminum housing with high power LED’s lens & toughened glass IP-66 including GI Pipe 40 mm 1.5 metre long mounting bracket fixed on building wall with necessary clamps, nuts and bolts and making connection with PVC copper flexible cable 1.5 Sqmm, complete all as specified and as directed. Make : Crompton Greaves Cat Part No LSTP-60-CDL-M / C&S Cat part No LTESS60WLED/LS or equivalent model from makes as specified in Appendix ‘F’

Note:- Excavation, returning filling and removing for E & M Portion shall also be measured and paid under Srl item Nos 125, 126 & 127 here in before of this BoQ.

NARESH KUMAR AND COMPANY

M/S Vishwakarma Builders

M/s K.S. Constructions