Repair/Maint of water suply motor pump, filtration plant, chlorine plant sets with connected items at Birdhwal, Nanu wali kothi and other locations under GE (Army) Suratgarh at Suratgarh Mil Stn

Amount

M&L for opening of centrifugal pump (Make: Kirloskar, Model : UP 250/38) with discharge capacity 119000 gallons per hour at 50 metre head, with 150 HP elelctric motor by disconnecting from motor, dismantling and replacement of unserviceable parts such as impeller, bushes, shaft sleeves, ball bearing, nut bolts, gland plate, gasket, water hose pipe etc and lathe work/turning, grinding etc on shaft and shaft key way as required including greasing/oiling and re-assembling at the same location with proper alignment with motor and testing complete all as specified and directed by Engineer-in-charge. Note : - (i) Major items like impeller, bearing, bush, gland plate, tyre coupling, coupling assembly shall be measured and paid for separately under respective items of BOQ as “Supply only”. (ii) Cost for transportaion to workshop and carry back to site after repair is inlcuded in the unit rate of item nothing extra shall be paid on this acount.

All as per serial item No 1 here-in-above but centrifugal pump (Make: Kirloskar, Model : UP 200/42) with discharge capacity 546 Cum per hour at 50 metre head, with 125 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but centrifugal pump (Make: Kirloskar, Model : UP 150/45) with discharge capacity 352 Cum per hour at 50 metre head, 1450 RPM with 100 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but centrifugal pump with discharge capacity 40000 gallons per hour at 45 metre head with 75 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but centrifugal pump (Make: Kirloskar, Model : UP 150/38) with discharge capacity 180 Cum per hour at 50 metre head, with 60 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but centrifugal pump with discharge capacity 35000 gallons per hour at 55 metre head with 50 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but centrifugal pump with discharge capacity 35000 gallons per hour at 40 metre head with 40 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but centrifugal pump with discharge capacity 30000 gallons per hour at 40 metre head with 30 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but centrifugal pump with discharge capacity 25000 gallons per hour at 35 metre head with 25 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but centrifugal pump with discharge capacity 20000 gallons per hour at 35 metre head with 20 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but centrifugal pump with discharge capacity 20000 gallons per hour at 30 metre head with 15 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but centrifugal pump with discharge capacity 15000 gallons per hour at 25 metre head with 12.5/10 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but centrifugal pump with discharge capacity 10000 gallons per hour at 25 metre head with 7.5 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but centrifugal pump with discharge capacity 10000 gallons per hour at 25 metre head with 5 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but monoblock pump set with 7.5 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but monoblock pump set with 5 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No1 here-in-above but monoblock pump set with 3 HP elelctric motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 1 here-in-above but monoblock pump set with 1 to 2 HP elelctric complete all as specified and directed by Engineer-in-charge.motor

Supply only bronze impeller with key suitable for centrifugal Pump set with 150 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for centrifugal Pump set with 150 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for centrifugal Pump set with 150 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for centrifugal Pump set with 150 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Rubber tyre coupling (TC/K/019) suitable for centrifugal Pump set with 150 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only CI impeller with key suitable for centrifugal Pump set with 125 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for centrifugal Pump set with 125 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for centrifugal Pump set with 125 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for centrifugal Pump set with 125 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Rubber tyre coupling (TC/K/019) suitable for centrifugal Pump set with 125 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only Coupling assembly, FC type, suitable for flexible tyre suitable for centrifugal Pump set with 150/125 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only CI impeller with key (CI/382) suitable for centrifugal Pump set with 100 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for centrifugal Pump set with 100 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for centrifugal Pump set with 100 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for centrifugal Pump set with 100 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Rubber tyre coupling suitable for centrifugal Pump set with 100 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only stainless steel pump shaft suitable for centrifugal Pump set with 100/125/150 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only CI impeller with key suitable for centrifugal Pump set with 75 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for centrifugal Pump set with 75 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for centrifugal Pump set with 75 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for centrifugal Pump set with 75 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Rubber tyre coupling suitable for centrifugal Pump set with 75 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only Coupling assembly, FC type, suitable for flexible tyre suitable for centrifugal Pump set with 75 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only bronze impeller with key suitable for centrifugal Pump set with 60 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for centrifugal Pump set with 60 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for centrifugal Pump set with 60 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for centrifugal Pump set with 60 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Rubber tyre coupling suitable for centrifugal Pump set with 60 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only CI impeller with key suitable for centrifugal Pump set with 50 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for centrifugal Pump set with 50 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for centrifugal Pump set with 50 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for centrifugal Pump set with 50 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Rubber tyre coupling suitable for centrifugal Pump set with 50 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only Coupling assembly, FC type, suitable for flexible tyre suitable for centrifugal Pump set with 50 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only stainless steel pump shaft suitable for centrifugal Pump set with 50/60/75 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only CI impeller with key suitable for centrifugal Pump set with 40 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for centrifugal Pump set with 40 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for centrifugal Pump set with 40 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for centrifugal Pump set with 40 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Rubber tyre coupling suitable for centrifugal Pump set with 40 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only Coupling assembly, FC type, suitable for flexible tyre suitable for centrifugal Pump set with 40 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only CI impeller with key suitable for centrifugal Pump set with 30 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for centrifugal Pump set with 30 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for centrifugal Pump set with 30 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for centrifugal Pump set with 30 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Rubber tyre coupling suitable for centrifugal Pump set with 30 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only Coupling assembly, FC type, suitable for flexible tyre suitable for centrifugal Pump set with 30 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only CI impeller with key suitable for centrifugal Pump set with 25 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for centrifugal Pump set with 25 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for centrifugal Pump set with 25 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for centrifugal Pump set with 25 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Rubber tyre coupling suitable for centrifugal Pump set with 25 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only Coupling assembly, FC type, suitable for flexible tyre suitable for centrifugal Pump set with 25 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only stainless steel pump shaft suitable for centrifugal Pump set with 20/25/30/40 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only CI impeller with key suitable for centrifugal Pump set with 20 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for centrifugal Pump set with 20 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for centrifugal Pump set with 20 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for centrifugal Pump set with 20 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Rubber tyre coupling suitable for centrifugal Pump set with 20 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only Coupling assembly, FC type, suitable for flexible tyre suitable for centrifugal Pump set with 20 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only CI impeller with key suitable for centrifugal Pump set with 15 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for centrifugal Pump set with 15 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for centrifugal Pump set with 15 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for centrifugal Pump set with 15 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Rubber tyre coupling suitable for centrifugal Pump set with 15 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only Coupling assembly, FC type, suitable for flexible tyre suitable for centrifugal Pump set with 15 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only CI impeller with key suitable for centrifugal Pump set with 12.5/10 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for centrifugal Pump set with 12.5/10 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for centrifugal Pump set with 12.5/10 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for centrifugal Pump set with 12.5/10 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Rubber tyre coupling suitable for centrifugal Pump set with 12.5/10 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only Coupling assembly, FC type, suitable for flexible tyre suitable for centrifugal Pump set with 12.5/10 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only CI impeller with key suitable for centrifugal Pump set with 7.5 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for centrifugal Pump set with 7.5 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for centrifugal Pump set with 7.5 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for centrifugal Pump set with 7.5 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Rubber tyre coupling suitable for centrifugal Pump set with 7.5 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only Coupling assembly, FC type, suitable for flexible tyre suitable for centrifugal Pump set with 7.5 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only CI impeller with key suitable for centrifugal Pump set with 5 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for centrifugal Pump set with 5 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for centrifugal Pump set with 5 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for centrifugal Pump set with 5 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Rubber tyre coupling suitable for centrifugal Pump set with 5 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only Coupling assembly, FC type, suitable for flexible tyre suitable for centrifugal Pump set with 5 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only CI impeller with key suitable for monoblock Pump set with 7.5 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for monoblock Pump set with 7.5 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for monoblock Pump set with 7.5 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for monoblock Pump set with 7.5 HP motor complete all as specified and directed by Engineer-in-charge.

M&L for rewinding the three phase induction motor suitable for monoblock Pump set with 7.5 HP motor with super enamelled copper winding wire of existing gauge including varnishing, baking, cotton tape and making proper electrical connection after taking out old brunt out motor complete all as specified and directed by Engineer-in-charge. Make of winding wire : Devidayal, Chetak Note : Transportation of motor to contractor's workshop is included in the unit rate of items and nothing extra shall be paid on this account.

Supply only CI impeller with key suitable for monoblock Pump set with 5 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for monoblock Pump set with 5 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for monoblock Pump set with 5 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for monoblock Pump set with 5 HP motor complete all as specified and directed by Engineer-in-charge.

M&L for rewinding the three phase induction motor suitable for monoblock Pump set with 5 HP motor with super enamelled copper winding wire of existing gauge including varnishing, baking, cotton tape and making proper electrical connection after taking out old brunt motor complete all as specified and directed by Engineer-in-charge. Make of winding wire : Devidayal, Chetak Note : Transportation of motor to contractor's workshop is included in the unit rate of items and nothing extra shall be paid on this account.

Supply only CI impeller with key suitable for monoblock Pump set with 3 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for monoblock Pump set with 3 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for monoblock Pump set with 3 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for monoblock Pump set with 3 HP motor complete all as specified and directed by Engineer-in-charge.

M&L for rewinding the three phase induction motor suitable for monoblock Pump set with 3 HP motor with super enamelled copper winding wire of existing gauge including varnishing, baking, cotton tape and making proper electrical connection after taking out old brunt motor complete all as specified and directed by Engineer-in-charge. Make of winding wire : Devidayal, Chetak Note : Transportation of motor to contractor's workshop is included in the unit rate of items and nothing extra shall be paid on this account.

Supply only CI impeller with key suitable for monoblock Pump set with 1 to 2 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for monoblock Pump set with 1 to 2 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for monoblock Pump set with 1 to 2 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for monoblock Pump set with 1 to 2 HP motor complete all as specified and directed by Engineer-in-charge.

M&L for rewinding the three phase induction motor suitable for monoblock Pump set with 1 to 2 HP motor with super enamelled copper winding wire of existing gauge including varnishing, baking, cotton tape and making proper electrical connection complete all as specified and directed by Engineer-in-charge. Make of winding wire : Devidayal, Chetak Note : Transportation of motor to contractor's workshop is included in the unit rate of items and nothing extra shall be paid on this account.

M&L for rewinding the three phase electric motor of 150 HP, 415 volts, AC with super enamelled copper winding wire of existing gauge including varnishing, baking, cotton tape and making proper electrical connection complete all as specified and directed by Engineer-in-charge. Make of winding wire : Devidayal, Chetak Note : Transportation of motor to contractor's workshop is included in the unit rate of items and nothing extra shall be paid on this account.

All as per serial item No 123 here-in-above but electric motor of 125 HP

All as per serial item No 123 here-in-above but electric motor of 100 HP

All as per serial item No 123 here-in-above but electric motor of 75 HP

All as per serial item No 123 here-in-above but electric motor of 60 HP

All as per serial item No 123 here-in-above but electric motor of 50 HP

All as per serial item No 123 here-in-above but electric motor of 40 HP

All as per serial item No 123 here-in-above but electric motor of 30 HP

All as per serial item No 123 here-in-above but electric motor of 25 HP

All as per serial item No 123 here-in-above but electric motor of 20 HP

All as per serial item No 123 here-in-above but electric motor of 15 HP

All as per serial item No 123 here-in-above but electric motor of 12.5/10 HP

All as per serial item No 123 here-in-above but electric motor of 7.5 HP

All as per serial item No 123 here-in-above but electric motor of 5 HP

All as per serial item No 123 here-in-above but electric motor of 3/2 HP

All as per serial item No 123 here-in-above but electric motor of 1/1.5 HP

Taking down old unserviceable ball bearing carefully S&F ball bearing suitable for electric motor of capacity 150 HP motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 139 here-in-above but for electric motor of 125 HP

All as per serial item No 139 here-in-above but for electric motor of 100 HP

All as per serial item No 139 here-in-above but for electric motor of 75 HP

All as per serial item No 139 here-in-above but for electric motor of 60 HP

All as per serial item No 139 here-in-above but for electric motor of 50 HP

All as per serial item No 139 here-in-above but for electric motor of 40 HP

All as per serial item No 139 here-in-above but for electric motor of 30 HP

All as per serial item No 139 here-in-above but for electric motor of 25 HP

All as per serial item No 139 here-in-above but for electric motor of 20 HP

All as per serial item No 139 here-in-above but for electric motor of 15 HP

All as per serial item No 139 here-in-above but for electric motor of 12.5/10 HP

All as per serial item No 139 here-in-above but for electric motor of 7.5 HP

All as per serial item No 139 here-in-above but for electric motor of 5 HP

All as per serial item No 139 here-in-above but for electric motor of 3/2 HP

All as per serial item No 139 here-in-above but for electric motor of 1/1.5 HP

Taking down old unserviceable metal body cooling fan and S&F cooling fan suitable for electric motor of capacity 150/125/100 HP motor including replacement of lock and key, nut etc complete all as specified and directed by Engineer-in-charge.

All as per serial item No 155 here-in-above but for electric motor of 75/60/50 HP

All as per serial item No 155 here-in-above but for electric motor of 40/30 HP

All as per serial item No 155 here-in-above but for electric motor of 25/20 HP

All as per serial item No 155 here-in-above but for electric motor of 15/12.5/10 HP

All as per serial item No 155 here-in-above but for electric motor of 7.5/5 HP

All as per serial item No 155 here-in-above but for electric motor of 3/2/1.5/1 HP

Supply & fix in replacement of terminal box with cover, screw, nut, bolts etc suitable for electric motor of capacity 150/125/100 HP complete all as specified and directed by Engineer-in-charge.

All as per serial item No 162 here-in-above but for electric motor of 75/60/50 HP

All as per serial item No 162 here-in-above but for electric motor of 40/30 HP

All as per serial item No 162 here-in-above but for electric motor of 25/20 HP

All as per serial item No 162 here-in-above but for electric motor of 15/12.5/10 HP

All as per serial item No 162 here-in-above but for electric motor of 7.5/5 HP

All as per serial item No 162 here-in-above but for electric motor of 3/2/1.5/1 HP

Supply & Fixing replacement of terminal bakelite connection plate with nut, bolts etc suitable for 3 phasse, 415 volts, AC, star/delta connection, electric motor of capacity 150/125/100 HP including replacement of copper thimble, brass nut, bolt, washer complete all as specified and directed by Engineer-in-charge.

All as per serial item No 169 here-in-above but for electric motor of 75/60 HP

All as per serial item No 169 here-in-above but for electric motor of 50/40 HP

All as per serial item No 169 here-in-above but for electric motor of 30/25 HP

All as per serial item No 169 here-in-above but for electric motor of 20 HP

All as per serial item No 169 here-in-above but for electric motor of 15/12.5/10 HP

All as per serial item No 169 here-in-above but for electric motor of 7.5/5 HP

All as per serial item No 169 here-in-above but for electric motor of 3/2/1.5/1 HP

M&L for taking out defictive submersible pump set of capacity 5/7.5 HP Capacity from bore well after disconnecting electrical connections, transportation to workshop for repair, dismantling the pump set for detection of repair such as rewinding of motor, replacement of iron stainer, bronze impeller, gun metal bushes stainless steel sleeve, impeller key, thrust bearing, replacement of unserviceable nut-bolts, washer, lugs, terminal plate, reassembling, lowering of pump & strainer in well in its original position, making proper electrical connections, commissioning & testing complete all as specified and directed by Engineer-in-charge. Note : - (i) Cost for transportaion to workshop carry back to site after repair is inlcuded in the unit rate of item quoted by contractor and nothing extra shall be paid on this acount. (ii) Rewinding of submersible motor, Iron stainer, bronze impeller, gun metal bushes stainless steel sleeve, impeller key and thrust bearing if required for replacement shall be paid separetly against respective items of BOQ as "Supply only". (iii) Lathe work and grinding of shaft if required shall be paid separately against respective items of BOQ. (iv) Cost of new nuts, bolts, washers, lugs and terminal plate required to be replaced is included in the unit rate of item quoted by the contractor and nothing extra shall be paid on this account.

All as per serial item No. 177 here-in-above but submersible pump set of capacity 12.5 HP

Supply only Iron stainer suitable for submersible pump of capacity 5/7.5 HP, 6 stage complete all as specified and as directed by Engineer –in-charge.

Supply only Iron stainer suitable for submersible pump of capacity 12.5 HP, 6 stage complete all as specified and as directed by Engineer –in-charge.

Supply only Bronze impeller with key suitable for submersible pump of capacity 5/7.5 HP, 6 stage complete all as specified and as directed by Engineer –in-charge.

Supply only Bronze impeller with key suitable for submersible pump of capacity 12.5 HP, 6 stage complete all as specified and as directed by Engineer –in-charge.

Supply only Gun metal Bush suitable for submersible pump of capacity 5/7.5 HP, 6 stage complete all as specified and as directed by Engineer –in-charge.

Supply only Gun metal Bush suitable for submersible pump of capacity 12.5 HP, 6 stage complete all as specified and as directed by Engineer –in-charge.

Supply only Stainless steel sleeves suitable for submersible pump of capacity 5/7.5 HP, 6 stage complete all as specified and as directed by Engineer –in-charge.

Supply only Stainless steel sleeves suitable for submersible pump of capacity 12.5 HP, 6 stage complete all as specified and as directed by Engineer –in-charge.

Supply only Thrust bearing of Gun metal suitable for submersible pump of capacity 5/7.5 HP, 6 stage complete all as specified and as directed by Engineer –in-charge.

Supply only Thrust bearing of Gun metal suitable for submersible pump of capacity 12.5 HP, 6 stage complete all as specified and as directed by Engineer –in-charge.

Supply only water seal suitable for submersible pump of capacity 5/7.5 HP, 6 stage complete all as specified and as directed by Engineer –in-charge.

Supply only water seal suitable for submersible pump of capacity 12.5 HP, 6 stage complete all as specified and as directed by Engineer –in-charge.

Supply only motor coupling suitable for submersible pump of capacity 5/7.5 HP, 6 stage complete all as specified and as directed by Engineer –in-charge.

Supply only motor coupling suitable for submersible pump of capacity 12.5 HP, 6 stage complete all as specified and as directed by Engineer –in-charge.

Supply only PVC rope minimum 2.5cm dia for submersible pump complete all as specified and as directed by Engineer –in-charge.

M&L for rewinding of motor of submersible pump set of capacity 5 HP with super enamelled copper winding wire of existing gauge including varnishing, baking, cotton tape and greasing of bearings, bushes and other connected parts and making necessary hook/clamp arrangement or body for attachning PVC rope complete all as specified and directed by Engineer-in-charge. Make of winding wire : Devidayal, Chetak

All as per serial item No 194 here-in-above but for motor of submersible pump set of capacity 7.5 HP

All as per serial item No 194 here-in-above but for motor of submersible pump set of capacity 12.5 HP

M&L for lath work on machine as filling of material, welding, grinding and finishing for shaft of submersible pump of capacity 5/7.5, 6 stage complete all as specified and as directed by Engineer –in-charge.

M&L for lath work on machine as filling of material, welding, grinding and finishing for shaft of submersible pump of capacity 12.5, 6 stage complete all as specified and as directed by Engineer –in-charge.

S&F in replacement of GI coloumn pipe for submersible pump, 80mm dia bore 'heavy grade' ISI marked both end flanged and 3 mtr length piece with nut bolts and gasket etc complete all as specified and as directed by Engineer –in-charge.

S&F in replacement of PVC coloumn pipe, heavy duty, ISI marked for submersible pump, 80mm thickness of pipe of socket/outer thread end of 3 mtr length complete all as specified and as directed by Engineer –in-charge.

All as per serial item No 202 here-in-above but for electrical starter panel for motor of capacity of 75/60/50 HP

All as per serial item No 202 here-in-above but for electrical starter panel for motor of capacity of 40/30/25 HP

All as per serial item No 202 here-in-above but for electrical starter panel for motor of capacity of 20/15 HP

All as per serial item No 202 here-in-above but for electrical starter panel for motor of capacity of 12.5/10/7.5 HP

All as per serial item No 202 here-in-above but for electrical starter panel for motor of capacity of 5/3 HP

Supplying, laying, jointing & testing in replacement submersible cable, 1100 volts, IS:694, flat type, copper conductor of size 16 Sqmm, 3 core complete all as specified & as directed by Engineer –in-charge.

All as per serial item No. 208 here-in-above but 10 Sqmm 3 core.

All as per serial item No. 208 here-in-above but 6 Sqmm 3 core.

All as per serial item No. 208 here-in-above but 4 Sqmm 3 core.

Supplying, laying & jointing in replacement of PVC insulated single core, copper conductor cable, 1100 volts, IS:694, unsheathed, heat resistant and flame retardent of size 70 Sqmm complete all as specified & as directed by Engineer –in-charge.

All as per serial item No. 212 here-in-above but 50 Sqmm.

All as per serial item No. 212 here-in-above but 35 Sqmm.

All as per serial item No. 212 here-in-above but 25 Sqmm.

Supply only in replacement MCCB 3 Pole 200 Amps, thermal magnetic release having, breaking capacity 50 KA, 415 Volt complete all as specified and as directed by Engineer-in-Charge. Make : Legrand Cat Part No. DPX³ 250 420268 or equivalent in L&T / Schneider / ABB

Supply only in replacement MCCB 3 Pole 160 Amps, thermal magnetic release having, breaking capacity 50 KA, 415 Volt complete all as specified and as directed by Engineer-in-Charge. Make : Legrand Cat Part No. DPX³ 160 420127 or equivalent in L&T / Schneider / ABB

Supply only in replacement MCCB 3 Pole 25 - 100 Amps, thermal magnetic release having, breaking capacity 50 KA, 415 Volt complete all as specified and as directed by Engineer-in-Charge. Make : Legrand Cat Part No. DPX³ 160 420121-25 or equivalent in L&T / Schneider / ABB

Supply only in replacement of power contactor, AC3 rating, 160 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

Supply only in replacement of power contactor, AC3 rating, 120 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

Supply only in replacement of power contactor, AC3 rating, 95 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

Supply only in replacement of power contactor, AC3 rating, 80 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

Supply only in replacement of power contactor, AC3 rating, 65 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

Supply only in replacement of power contactor, AC3 rating, 50 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

Supply only in replacement of power contactor, AC3 rating, 40 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

Supply only in replacement of power contactor, AC3 rating, 38 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

Supply only in replacement of power contactor, AC3 rating, 32 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

Supply only in replacement of power contactor, AC3 rating, 25 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

Supply only in replacement of power contactor, AC3 rating, 18 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

Supply only in replacement of power contactor, AC3 rating, 12 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

Supply only in replacement of power contactor, AC3 rating, 9 Amps, 3 Pole, AC control with Auxiliary contacts 2 NO + 2NC, suitable for coil voltage 110 V, 220, 240 & 415 volts, 50 Hz complete all as specified and as directed by Engineer-in-Charge. Make: Schneider/ L&T/ Siemens

Supply only in replacement of thermal over load relay adjustment range 124-198 / 84-135 / 62-99 amps with all electrical wiring complete all as specified & as directed by Engineer-in-charge.

All as per item No 232 here-in-above but adjustment range 48-65 Amps

All as per item No 232 here-in-above but adjustment range 16-24/ 23-32 / 30-40 / 37-50 Amps

All as per item No 232 here-in-above but adjustment range 12-18 Amps

All as per item No 232 here-in-above but adjustment range 7-10 / 5.5-8 / 4-6 / 2.5-4 Amps

Supply only in replacement of electronic timer 0 to 30 second for star - delta changeover, DIN mounting complete all as specified & as directed by Engineer-in-charge.

Supply only in replacement of 3 phase preventor (SPP) with auto reset, 415 Volts AC complete all as specified & as directed by Engineer-in-charge.

Supply only in replacement of digital voltmeter (50-550V), 3 phase, 96x96 mm with CT complete all as specified & as directed by Engineer-in-charge.

Supply only in replacement of digital ammeter (0-500V), 3 phase, 96x96 mm with CT/PT complete all as specified & as directed by Engineer-in-charge.

Supply only in replacement of push button, ON/OFF, Ref/Green complete all as specified & as directed by Engineer-in-charge.

Supply only in replacement of LED indication lamp Red/Blue/Green with holder complete all as specified & as directed by Engineer-in-charge.

Supply only in replacement of MCB 32 Amps, Triple Pole & Neutral 415 Volts, 10 KA, ‘C’ Curve complete all as specified & as directed by Engineer-in-charge. Make :- Legrand Cat Part No 408680 or equivalent in L&T / Schneider / ABB

Supply only in replacement of MCB 6 Amps, Single Pole 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Make :- Legrand Cat Part No 408587 or equivalent in L & T / Havells / Schneider

Supply only in replacement of submersible pump controller fully star delta starter, in sheet-steel enclosure AC3 duty, 415 volts, 50 Hz, 3 Phase for 15 HP pump and relay 9-14 Amps with i-protector (i-VDSM) for voltage single phasing, under voltage fault, over voltage fault complete all as specified & as directed by Engineer-in-charge. Make: L&T cat ref. No SS95984DOAO (MUG20 FASD) / Schneider / Siemens

Supply only in replacement of submersible pump controller fully star delta starter, in sheet-steel enclosure AC3 duty, 415 volts, 50 Hz, 3 Phase for 20 HP pump and relay 13-21 Amps with i-protector (i-VDSM) for voltage single phasing, under voltage fault, over voltage fault complete all as specified & as directed by Engineer-in-charge. Make: L&T cat ref. No SS95984DOAO (MUG20 FASD) / Schneider / Siemens

S&F in replacement of pressure gauge (0-14) Kg/Sq cm, in stainless steel casing, size 100 mm with check valve complete all as specified & as directed by Engineer-in-charge. Make: H Guru/Fiebig

S&F in replacement of door hinges for single/double door CRCA sheet electrical panel by welding or nut /bolts as per esixting type complete all as specified & as directed by Engineer-in-charge.

S&F in replacement of door lock for electrical panel, key less panel lock, 90 degree locking, half knob type complete all as specified & as directed by Engineer-in-charge.

S&F in replacement of earth continuity conductor 25 x 4 mm galvanized iron strip, fixed to wall on batten or recess or chases or buried in ground or drawn in pipe or any other indicated situation for earthing etc as required complete all as specified & as directed by Engineer-in-charge.

Preparation of old painted steel surfaces of panel body of any size incl scrapping old paint, denting and applying two coats of spray paint using synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-charge.

S&F in replacement name plate for pump set etc of size 300x400 mm with thickness of 3 mm PVC sheet as per sample and including printing with digitilize printing the details of machinery such as SM No, MES No., Pump set/motor detail as capacity etc and fixed on wall complete all as specified and directed by Engineer-in-charge.

Disconnecting of gear box of Make : Elecon, Type : NU, size 3 inch, Ratio 70:1, by strip opening and greasing, oiling, lathe work, grinding finishing work on shaft including replacement of shaft key, bush/bearing, oil seal, packing, drain plug etc and painting with one coat of synthetic enamel weather proof paint as per existing colour code complete all as specified and directed by Engineer-in-charge. Note :(i) Items like gear grease, Wedge pully with key and belt etc required to replace shall be measured and paid for separately under respective items of BOQ as “Supply only”

Supply only gear grease Castrol EPL2 / Indian Oil Servogem EP2 complete all as specified & as directed by Engineer-in-charge.

Supply only in replacement wedge pully with key for gear box complete all as specified & as directed by Engineer-in-charge.

Supply only in replacement belt B38/B46 for gear box complete all as specified & as directed by Engineer-in-charge. Make : - Fenner, Dunlop

M&L for servicing of Air blower of Make : Everest Blower, Model : LB17 of capacity 2460 Cum per hour, speed 1510 RPM with 50 HP motor by greasing, oiling and draining out of old oil and charging of new oil after replacement of unserviceable items (Suction filter, Set of seal and O ring, bearing, piston rings, bush, retainer, pressure guage, gasket, nut, bolts & washer) as per AM kit by the OEM only and any other items required for smooth functioning of blowers complete all as specified and directed by Engineer-in-charge. Note :(i) AM kit (Suction filter, Set of seal and O ring, bearing, piston rings, bush, retainer, pressure guage, gasket, nut, bolts & washer) shall be measured and paid for separately under respective items of BOQ as “Supply only” (ii) Servicing shall be done as per OEM recommendation and by service engineer (Everest blower).

Supply only in replacement of AM kit for Air blower of Make : Everest Blower, Model : LB17 of capacity 2460 Cum per hour, speed 1510 RPM with 50 HP motor (OEM spare parts only) containing of following: (a) Suction filter (b) Set of seal and O ring (c) Set of bearing (d) Set of piston Rings with bush (e) Set of retainer (f) Pressure guage (g) Set of Gasket

Supply only in replacement of Vee belt suitable for Air blower of Make : Everest Blower, Model : LB17 of capacity 2460 Cum per hour, speed 1510 RPM with 50 HP motor complete all as specified & as directed by Engineer-in-charge. Make : - Turboflex, Fenner

Disconnecting of Air blower of Make : Everest Blower, of capacity 1230 Cum per hour, speed 1510 RPM with 15/20 HP motor by greasing, oiling and draining out of old oil and charging of new oil after replacement of unserviceable items (Suction filter, Set of seal and O ring, bearing, piston rings, bush, retainer, pressure guage, gasket, nut, bolts & washer) as per AM kit by the OEM only and any other items required for smooth functioning of blowers complete all as specified and directed by Engineer-in-charge. Note :(i) AM kit (Suction filter, Set of seal and O ring, bearing, piston rings, bush, retainer, pressure guage, gasket, nut, bolts & washer) shall be measured and paid for separately under respective items of BOQ as “Supply only” (ii) Servicing shall be done as per OEM recommendation and by service engineer (Everest blower).

Supply only in replacement of AM kit for Air blower of Make : Everest Blower, of capacity 1230 Cum per hour, speed 1510 RPM with 15/20 HP motor (OEM spare parts only) containing of following: (a) Suction filter (b) Set of seal and O ring (c) Set of bearing (d) Set of piston Rings with bush (e) Set of retainer (f) Pressure guage (g) Set of Gasket

Supply only Gear oil for air blower (Castrol Hypoy 90EP / HP EP90)complete all as specified & as directed by Engineer-in-charge.

Supply only in replacement of Vee belt suitable for Air blower of Make : Everest Blower, of capacity 1230 Cum per hour, speed 1510 RPM with 15/20 HP motor complete all as specified & as directed by Engineer-in-charge. Make : - Turboflex, Fenner

S&F in replacement of Gland rope of size 8/10/12 Sqmm complete all as specified & as directed by Engineer-in-charge. Make : - Turboflex, Fenner

S&F in replacement of MBBR media for sewage treatment, fluidized bro media, made of vigin PP UV stablized, model PP25, media height 16 mm, media diameter 22 mm with effective specific surface area of media 400 Sqm colour black, cylinderical with external fins, voidage 98% complete all as specified & as directed by Engineer-in-charge.

S&F in replacement of tube settler media for sewage treatment, square shape, PVC seperator height 500mm, with 5.5 Sqm setting area complete all as specified & as directed by Engineer-in-charge.

S&F in replacement butterfly valve of size 80mm, CI body, SS disc & stem, lever operated conforming to IS-13095 with nut, bolts, washer and gasket complete all as specified and directed by Engineer-in-charge.

S&F in replacement gun metal globe or gate valve 80mm bore with iron wheel head, screwed both ends for iron pipes complete all as specified and directed by Engineer-in-charge.

S&F in replacement gun metal globe or gate valve 50mm bore with iron wheel head, screwed both ends for iron pipes complete all as specified and directed by Engineer-in-charge.

Opening of chlorination system, semi automatic type with gas chlorinator, ejector, PVC pipes, valve etc capacity of chlorine dosing upto 1.5 Kg/Hour. Make : Jal Corporation Baroda / Chloromax / RMCO by disconnecting from the chloroination system/cylinder and strip opening and checking for unserviceable parts and making functional by replacment of unservicebale parts i.e. O rings, filters, gaskets, main diaphragm, disc diaphragm, ring diaphragm, ejector diaphragm, spring sports, nozzel, adeptor socket with washer for PVC flexible pipe etc or any other part required to make the device functional and refixing the same and testing complete all as specified and directed by Engineer-in-charge. Note :(i) Major items like brass valve, vaccume type flow regulator with regulator valve, rotameter tube with O ring, Yoke clamp assembly, diaphragm pressure gauge, main diaphragm with plate assembly & ejector diaphragm assembly with spring and nut shall be measured and paid for separately under respective items of BOQ as “Supply only”. (ii) The cost of transportation is included in the unit rate of this item nothing extra shall be paid on this account.

Supply only in replacement of heavy duty brass valve (IS:3224) suitbale for chlorine gas cylinder (100 Kg) for connection with chorinator complete all as specified and directed by Engineer-in-charge.

Supply only in replacement of vaccume type flow regulator with regulator valve, rotameter tube with O ring complete all as specified and directed by Engineer-in-charge.

Supply only in replacement of yoke clamp assembly for chlorinator mounting on cylinder complete all as specified and directed by Engineer-in-charge.

Supply only in replacement of diaphragm pressure guage complete all as specified and directed by Engineer-in-charge.

Supply only in replacement of main diaphragm with plate assembly complete all as specified and directed by Engineer-in-charge.

Supply only in replacement of main ejector diaphragm assembly with spring and nut complete all as specified and directed by Engineer-in-charge.

S&F in repair ejector suitable for chlorine dosing capacity upto 1.5Kg/Hour as per existing model and type complete all as specified and directed by Engineer-in-charge.

S&F in repair gas chlorinator direct cylinder mounted suitable for chlorine dosing capacity upto 1.5 Kg per hour as per existing model and type complete with necessary fitting and testing complete all as specified and directed by Engineer-in-charge.

S&F in repair 25mm bore UPVC pipes of approved make or equivalent including fittings such as socket, bend & tee conrforming to IS 13592-1992 complete all as specified & directed by Engineer-in-charge.

S&F in repair 32mm bore UPVC pipes of approved make or equivalent including fittings such as socket, bend & tee conrforming to IS 13592-1992 complete all as specified & directed by Engineer-in-charge.

S&F in repair 25mm bore PVC ball valve, heavy duty complete all as specified & directed by Engineer-in-charge.

S&F in repair 32mm bore PVC ball valve, heavy duty complete all as specified & directed by Engineer-in-charge.

S&F in repair 9mm bore PVC flexible water pipe, heavy duty complete all as specified & directed by Engineer-in-charge.

S&F in replacement PVC foot valve for 25 mm bore pipe, ISI marked complete all as specified and directed by Engrineer-in-Charge.

S&F in replacement PVC foot valve for 32 mm bore pipe, ISI marked complete all as specified and directed by Engrineer-in-Charge.

M&L for servicing of multi stage centrifugal pump for chlorination system with 2/3 HP motor by replacement of unservicebale parts i.e. impeller, bearing, bush, coupling including welding. grinding, lathe work etc as required complete all as specified and directed by Engrineer-in-Charge. Note : (i) Major items like impeller, bearing, bush, coupling assembly shall be measured and paid for separately under respective items of BOQ as “Supply only”.

Supply only impeller with key suitable for multi stage pump for chlorination system with 2/3 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for multi stage pump for chlorination system with 2/3 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for multi stage pump for chlorination system with 2/3 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only coupling assembly suitable for multi stage pump for chlorination system with 2/3 HP motor complete all as specified and directed by Engineer-in-charge.

Preparation of old painted surfaces of chlorine cylinder of capacity 100 Kg incl scrapping old paint, and applying two coats of spray paint using synthetic enamel paint over and writing with black colour paint as GE (Army) Suratgarh, Sr. No etc complete all as specified and directed by Engineer-in-charge.

M&L for servicing of calcium hypochloride dosing system capacity upto 500 gm/hour by strip opening of dosing pump and replacement of unservicebale parts and making functional and repair to electrical connection and replacement of capacitor suitable for dosing, mixing motor upto 1.5 HP complete all as specified and directed by Engrineer-in-Charge.

M&L for rewinding the single phase chemical mixing motor capacity upto 1.5 HP, AC with super enamelled copper winding wire of existing gauge including varnishing, baking, cotton tape and making proper electrical connection complete all as specified and directed by Engineer-in-charge. Make of winding wire : Devidayal, Chetak Note : Transportation of motor is included in the unit rate of items nothing extra shall be paid on this account.

M&L for rewinding the single phase motor for dosing pump capacity upto 1.5 HP, AC with super enamelled copper winding wire of existing gauge including varnishing, baking, cotton tape and making proper electrical connection complete all as specified and directed by Engineer-in-charge. Make of winding wire : Devidayal, Chetak Note : Transportation of motor is included in the unit rate of items nothing extra shall be paid on this account.

Taking down old unserviceable filter media complete from pressure filter by strip opening and cleaning from inside and laying of new filter media as per original equipment manufacturer recommendation (Make : Chloromax) capacity aprox 50000 ltrs per hour and size 1800mm suitbale for raw water treatment, reducing turbidity etc including one coat of synthetic enamel paint on outer surface by spray gun as per existing colour code after preparation of old surface by removing old unserviceable paint and testing complete all as specified and directed by Engrineer-in-Charge.

Removing of existing filter media i.e. gravel and sand from filter bed of filteration plant and Screening, seperating, cleaning and washing the gravels / sand obtained from filter bed with necessary equipments, T&P and keeping aside for re-use and removing the spoil to a distance not exceeding 100 mtrs keeping aside for cleaning or re-use etc complete all as specified and directed by Engrineer-in-Charge.

Removing of unserviceable filter media as obtained from washed filter media of different size to a distance not exceeding 200 mtr from site complete all as specified and directed by Engrineer-in-Charge.

Laying only of cleaned, washed filter media of different size as obtained, layer after layer as complete all as specified and directed by Engrineer-in-Charge.

Supply & laying pebbles of size 20-40mm, cleaned, treated, disinfected and suitable for water filteration plant in 25/50 Kg PP begs complete all as specified and directed by Engrineer-in-Charge.

All as per item No 301 here-in-above but pebbles of size 12-20mm complete all as specified and directed by Engrineer-in-Charge.

All as per item No 301 here-in-above but pebbles of size 6-12mm complete all as specified and directed by Engrineer-in-Charge.

All as per item No 301 here-in-above but crushed gravels of size 3-6mm complete all as specified and directed by Engrineer-in-Charge.

All as per item No 301 here-in-above but coarse sand of size 2-4mm complete all as specified and directed by Engrineer-in-Charge.

All as per item No 301 here-in-above but fine sand of size 0.5-0.8mm complete all as specified and directed by Engrineer-in-Charge.

M&L for servicing of multi stage centrifugal pump (Make: Kirloskar, Model : CF444), 5/6 stage, having discharge capacity 2.5 LPS at 80mtr head, with 20 HP elelctric motor by oiling, greasing and replacement of unserviceable parts such as impeller, bushes, coupling including welding, turning, grinding, lathe work etc as required including and installing at same location with proper alignment with motor and testing complete all as specified and directed by Engineer-in-charge. Note: - (i) Major parts like impeller, bushes, shaft sleeve, ball bearing shall be measured and paid for separately as “Supply only” under respective items of BOQ. (ii) New Nuts, bolts, washers, copper thimbles, connectors and insulators if required for refixing shall be provided by the contractor, nothing extra shall be paid on this account. (iii) Transportation of motor is included in the unit rate of items nothing extra shall be paid on this account.

Supply only CI impeller with key suitable for multi stage centrifugal Pump set with 20 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Ball bearing suitable for multi stage centrifugal Pump set with 20 HP motor complete all as specified and directed by Engineer-in-charge. Make : NBC, SKF, TATA

Supply only Stainless steel Bush suitable for multi stage centrifugal Pump set with 20 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only Gland plate suitable for multi stage centrifugal Pump set with 20 HP motor complete all as specified and directed by Engineer-in-charge.

Supply only tyre coupling suitable for multi stage centrifugal Pump set with 20 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

Supply only Coupling assembly, suitable for multi stage centrifugal Pump set with 20 HP motor complete all as specified and directed by Engineer-in-charge. Make : Unique, Fenner

S&F in replacement On load changeover switch of 63 Amp Capacity, four pole with interlock and padlock facility and handle fixed in existing electric panel including all electrical connection and replacement of lugs / thimbles to existing cable and any addition / alteration to existing panel as required and directed by Engineer-in-Charge. Make : - L&T cat part No CO10630OOOO or equivalent in Havells / Legrand / Schneider

All as per item No 314 here-in-above but for capacity 160 Amps complete all as specified and directed by Engineer-in-charge. Make : - L&T cat part No CO21600OOOO or equivalent in Havells / Legrand / Schneider

All as per item No 316 here-in-above but for capacity 400 Amps complete all as specified and directed by Engineer-in-charge. Make : - L&T cat part No CO44000OOOO or equivalent in Havells / Legrand / Schneider ------------------------------------------------------------------------- Note :- A sum of Rs. 188837/- will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 36 to 39 (Schedule of Credit) of Tender documents.

SRI SAI CONSTRUCTION COMPANY