Construction of 620 Capacity Auditorium cum Atal Kala Bhawan At Aurangabad.

Earth work in excavation over areas (exceeding 30 cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m; disposal earth to be levelled and neatly dressed.

Excavating, supplying and filling of local earth (including royalty but excluding cairriage cost) by mechanical transport upto a lead of 3km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. If local earth is available at more than 3 km lead the actual lead must be approved by compitent authority. cairraiage of material will be paid seperately and calculated after deducting initial lead.

Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Extra for every additional lift of1.5m or pan thero of in all kind of soil etc all complete job

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Providing designation 100 A one brick EDGE soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l, etc all complete jobs.

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1:4:8(1 Cement: 4 coarse sand:8 graded stone aggregate 20 mm nominal size)

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete All work upto plinth level + Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C.

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete All works above plinth level upto floor V level Walls columns, pillars, posts cind struts

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete

Walls columns, pillars, posts cind struts

Beams, planth beams, girders, bressumers, cantilevers, Suspended floors lintels roofs and staircases including spiral cum 5677.20 staircases shelves etc

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete All work upto plinth level + Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C.

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete All work upto plinth level + Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C.

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete All work upto plinth level + Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C.

Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum.

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer- in-Charge

80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern.

Centring and shuttering including strutting, propping etc. and removal of form for.

Foundation

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Suspended floors

Shelves

Lintels, beams, plinth bams,

Columns

Stairs

Chajjas

Edge of Slab

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Brick work with bricks of class designation 100A in foundations and plinth in :

Brick work with bricks with fly ash bricks as per IS 12894(2002) & 3495 in foundation and plinth in :

Brick work with fly ash bricks as per IS 12894 (2002) & IS 3495 in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand )

Brick work with fly ash bricks as per IS 12894 (2002) & IS 3495 in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand ) + Extra tor Brick work in superstructure above plinth level upto floor V cum

Brick work with fly ash bricks as per IS 12894 (2002) & IS 3495 in foundations and plinth in : Cement mortar 1.:4 (1 cement: 4 coarse sand ) + Extra tor Brick work in superstructure above plinth level upto floor V cum

Providing 12 mm cement plaster of mix: 1:6(1 cement: 6 coarse sand)

Cement plaster in course sand 12 mm cement plaster of mix: 1:3 (1 cement:3 coarse sand) Neat cement punning

1:4(1 cement: 4 coarse sand )

1:4(1 cement: 4 coarse sand )

15 mm cement plaster on rough side of single or half brick wall of mix. 1:6(1 cement: 6 coarse sand )

6 mm cement plaster to ceiling of mix : 1:4(1 cement: 4 coarse sand)

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of near cement

15 mm cement plaster 1:3 (1 cement: 3 coarse sand ) finished with a floating coat of neat cement on the rough side of single or half brick wall.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications. Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm.

Applying priming coat with ready mixed zinc chromate yellow primer of approved brand and manufacture on steel galvanized iron/steel work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work

Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly. plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications. Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm.

Distempering with oil bound washa ble distemper of approved brand and manufacture to give an even shade . New work (two or more coats ) over and including priming coat with cement primer

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: incliding priming coat

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab upto 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for providing opening of required size & shape for wash basins/kitchen sink in kitchen platform. Vanity counters and similar location in marble/granite/stone work including necessary holes for pillar taps etc. including rubbing,moulding and polishing of cut edges etc. complete.

Chequered terrazo tiles 22 mm thick with marble chips of sozes upto 6 mm in floors jointed with neat cement slurry mixed with pigement to match the shade of the tiles, including rubbing and polshing complete on 20 nm thick bed of cement mortar 1:4 (1 cement:4 coarse sand) Medium shade using 50% white cement and 50% ordinary cement

Kota stone slab flooring over 20 mm (average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . Base with 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand 20 to 25 mm thick -

Kota stone slabs 20 mm thick in risers of steps skirting. Dado & pillars laid on 12 mm (average (thick cement mortar 1:3 (1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Details of cost for 10 sqm

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete. Size 600 X 1200

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

38 mm thick parquet (wood block) flooring of 1st class teak wood laid over 25 mm thick levelling layer of cement concrete 1:2:4(1 cement:2 coarse sand:4 store aggregate 10 mm nominal size) to be paid separately coated with a thin layer of hot bitumen (blown type) @ 2.45 kg per sqm. including fixing blocks in position after dipping in hot bitumen (blown type) upto half depth,planed,levelled smooth and finished complete

Providing& fixing inpositionPhenol bondedBamboowood flooring with planks of sizes 14mm thick, minimum 1800mm length and minimum100mmwide, inapprovedcolour, textureandfinish,having PerformanceAppraisalCertificate(PAC) issuedbyBuildingMaterials& TechnologyPromotionCouncil (BMTPC). The flooringshall be fixed withtongueandgrooveinterlockingsystem,withunderlaymentof4mm thickexpandedpolythylenefoamsheetshavingdensity40kg/cum,over preparedsurfacewithnecessaryquarterroundplanksofsize1900mm x18mmanddoorreducerofsize1900mmx44mm,whereverrequired. Thebomboowoodplanksshallhaveminimumdensityof1000Kg/cum &minimumHardness 1000Kgf. withEco friendlyUV coating, all complete as per direction of the Engineer in-char

Providing& fixing inpositionPhenol bondedBamboowood inwall skirtingwithplanksof sizes14mmthick, 1900mmlength (minimum) and 85mmwide(minimum), in approved colour, texture and finish, havingPerformanceAppraisal Certificate (PAC) issued byBuilding Materials&TechnologyPromotionCouncil (BMTPC).Theskirtingshall befixedwithSSscrews&rawlplugs,overunderlaymentof4mmthick, expandedpolyethylene foamsheetshaving40kg/cumdensityover prepared surface. The bomboowood planks shall haveminimum densityof 1000Kg/cum&minimumHardness 1000Kgf. withEco friendlyUVcoating, all completeasperdirectionof theEngineer in charge

Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile C

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-incharge.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Providing and fixing Aluminium work for door, window, etc. for fixed portion. -do-

Providing and fixing Ms double acting spring hinges. -do- 150 mm

Providing and laying tactile tile. -do- 150 mm

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of glass panes with glazing clips and special metal-sash putty of approved make complete including applying a priming coat of approved steel primer; xcluding the cost of metal beading and other fitting except necessary hinges or pivots as required

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer.Using M.S. angle 40x40x6 mm for diagonal braces

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required In gratings, frames, guard bar, ladders, railings, brackts. gates & similar works..

Providing and fixing glazing in aluminium door, window,ventilatorshutters and partitions etc. with EPDM rubber / neoprene gasketetc. complete as per the architectural drawings

Supplying iron angle of Size 50x50x6mm for using barbed wire as per suitable size and shape

Drilling 6mm Dia. In M.S. angle iron for fixing of staples etc. as per building specification and direction of E/l.

Labour for cutting of M.S. angle iron post to required length, one end splitted as fish tailed in a length of 150mm complete as per building specification and direction of E/l.

Labour for fitting and fixing barbed wire fencing in six rows horizontal up to a height of 1.85m and two diagonals including fixing of post in cement concrete at 2.5m centres including cost of staples (but excluding the cost of cement concrete, angle, iron post, its cutting and making holes, nuts & bolts) all complete as per building specification and direction of E/l.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.).

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots.nuts locking arrangement stoppers handies including applying a priming coat of approved steel primer.

Supplying and fixing-rolling shuters of approved make.made of required size of M.S.Iaths interlocked together through their intire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arragements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

Providing and fixing ball bearing for rolling shutters

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing bright finished brass night latch of approved quality including necessary screws etc. complete

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete 25 mm dia metre

Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etc. complete.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (overall area of door shutter to be measured)

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete: 2nd class teak wood

Providing and fixing bright finished brass peg stays 300 mm long of minimum weight 330 gms.to side hung steel windows with necessary welding and machine screws etc. complete

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings complete jncluding applying a priming coat of approved steel primer.

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing on wall face unplastidsed- PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised- PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Coupler

110 mm Single pushfit coupler

Single tee with door 110x110x110mm

110 mm bend

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing '@ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge. With fully perforated 12 mm thick micro tegular edged or 10 mm thick square edged GRG false ceiling tiles

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's 15 mm thick fully With perforated square/butt edge light weight calcium silicate panels/ tiles

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished welded type tubes

Providing and fixing 15 cm wide 45 cm over all semi circular plain G.S. sheet gutter with iron brackets 40x3 mm size bolts, nuts and washers etc. including making necessary connections with rain water pipes complete. 0.80 mm thick with zinc coating not less than 275 gm/m2

KLIP LOCK-700 P/F testing and commissionigof roofing make tata bluscope

Providing and fixing flashing ridge make tata bwescope

Providing and fixing thermal insilation with resin bonded fiber glass wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with G.I.J. or L hooks . Bolts and nuts 8 mm dia. G. 1. limpet and bitumen washers complete. . 0.63 mm thick with zinc coating not less than 275 gm/m2

Extra for providing and fixing wind ties of 40x6mm flat iron section.

Extra for making chamfered edges of beading Thermal Insulation of roofing with Expanded polystyrene fixed with suitable adhesive to the false ceiling as per the directions of the Engineer-in charge With Type N-Normal

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water

Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade:Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacture's specifications including appropriate priming coat, preparation of surface, etc. complete

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2)For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors,embedding in floors as required and making good

Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer in-charge

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications,drawings and direction of Engineer-in-charge complete.

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mmsand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and makinggood the walls andlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) onforming to IS : 7231, with all fittingsand floors wherever required : White Vitreous china Orissa pattern W.C. pan ofsize 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required 510x1040 mm bowl depth 250 mm

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 40 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Providing and fixing 600x120x5 mm glass shelf with edges round off,supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete

Providing and fixing PTMT Bottle Trap for Wash basin and sink Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms

Providing and fixing PTMT Waste Coupling for wash basin and sink,of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe.

Providing and fixing uplasticised PVC connection pipe with brass ions : 15 mm nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :

15 mm dia nominal bore

20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) :

25 mm nominal bore Horizontal

25 mm nominal bore Vertical

32 mm nominal bore Horizontal

32 mm nominal bore Vertical

40 mm nominal bore Horizontal

40 mm nominal bore Vertical

Providing and fixing C.I. sluice valves (with cap) complete with bolts,nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 100A

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

25 mm diameter pipe

32 mm diameter pipe

40 mm diameter pipe

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15 mm nominal bore

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.

Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand 6 graded stone aggregate 20 mm nominal size) including disposal of malba.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking gement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete

Supplying and fixing C.I. cover without frame for manholes :

Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality.

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal\ size) as per standard design

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. 300 mm dia.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. 300 mm dia.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths,as per direction of Engineer -in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.150 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Supplying and fittings 2 HP Submersible water pump with starter cables etc. all necessary fitting etc. all complete jobs.

Supplying and stacking of good earth at site including royalty but excluding carriage (earth measured in stacks will be reduced by 20 % for payment)

Screened through sieve of I.S. designation 4.75 mm

Mixing earth and sludge or manure in proportion specified or directed.

Spreading of sludge, dump manutre or/and good earth in required thickness (Cost of sludge, dump manure or/and good earth to be paid separately)

In rows 5 cm apart in either direction.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20 % 1 part of stacked volume of manure after reduction by 8 % ) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure sludge or extra good earth if needed to be paid for separately)

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8 :1 (8 parts of stacked volume of earth after reduction by 8% ) flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Supplying, Installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

Fabricating, Supplying, Erection, Testing and commissioning of Electrical control panel cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet,compartmentalised with hinged lockable doors, dust and vermin proof, coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and outgoings, suitable for operation on 415V, 3 Phase, 50Hz Ac supply with enclosure protection class IP42 as required:

Providing, laying , testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS:1239 including welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gasket etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required:

25 mm dia

50 mm dia

80 mm dia

100 mm dia

150 mm dia

Supply and fixing single headed internal hydrant valve with instanteneous Gunmetal/Stainless steel coupling of 63mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type-A) with blank Gunmetal/Stainless steel cap and chain as required.

Single headed Gunmetal

Supply,fixing,testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS:13095 of following size as required.

50 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes conforming to IS:5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required.

50 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing , installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6mm thick stainless steel, Grade 304, sheet with 3mm dia holes with stainless steel flange.

Supplying and fixing 63mm dia, 15m long RRL hose pipe with 63mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 ( Type-A) as required:

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20mm nominal dia water hose thermoplastic ( Textile reinforced) type-2 as per IS:12585 20mm nomonal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipments on wall. " Connections from riser with 25mm dia stop gunmetal valve & M.S Pipe and socket.

Supplying and fixing 63mm dia gun metal short branch pipe with 20mm nominal diameter size nozzle confirming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required.

Supplying and fixing for Fire Brigade Connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as required for suitable dia MS pipe connection conforming to IS 904 as required.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Upto 35 sq.mm

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following,complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

Supply, laying & connecting with Diesel Engine Fire Pump Electrical Panel at ground level with 3.5 core x 10 sq. mm. armored aluminum cable 1.1 kv grade.

Supply,Installation,Testing and commissioning of smoke detector with built in LED and mounting base with complete with all connections etc. as required.

Supply,Installation,Testing and commissioning of manual call box ABS in surface recessed complete with glass and push button etc as required.

Supply,Installation,Testing and commissioning of response indicator on surface having two LED metallic cover complete with all connection etc. as required.

Supply,Installation,Testing and commissioning of fire alarm sounder with facility to make announcement, mounted in ABS box with hinge cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supply,Installation,Testing and commissioning of sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault fire condition and all other standarad facilities as per IS:2189 with mimic diagram all area zone covered, complete with all connections, interconnections as required.

Supplying and laying of 2x1.5 sq.mm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of cross linkable ethelene propyline rubber (EPR) insulation and LSZH inner bedding, steel wire armounting & LSZH outer sheath complete as required, (rate of area protected in sq.mm)

M.S. hose cabinet with door fabricated from 16 g M.S. sheet with full glass door and locking arrangement, suitable to accommodate 1 Hydrant landing valve, 1 fire hose reel, 1nos.15m long 63mmdia hose,1-branch pipe, The door shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including suitably mounted on a raised masonry platform as required (Approx. size 1.2m x 2.1m). For internal hydrants.

ISI marked (IS:2878) Portable fire Extinguisher, Carbon-dioxide type flat base including valve, discharge hose of not less than 10 mm dia. 1m long & complete in all respects including initial fill with C02 gas confirming to IS:307-1966 filled to a filling ratio of not more than 0.667of not more than 0.667and wall suspension bracket.

'ABC' stored pressure type Dry Chemical Powder (Mono-Ammonium Phosphate ) 6 kg fire extinguisher with fixing hangers, hose, brackets, screws to required size etc., complete as per IS:14609.

Door Frame Metal Detector

Hand Held Metal Detector

Office Table made of MS ERW round tube dia 25.4 x 1.2mm thick with 18mm thick Pre Laminated top size 1199 X 590 X 735 mm with one side one drawer unit made of .5mm thick CRCA sheet mild steel, All steel components have powder coated paint fitted with lock.

3 Seater Sofa The side frame assembly made of 38mm Dia 2mm thick is fitted to the two ends of the connecting beam assembly to form the leg-cum-armrest assembly. It is made of a MS. E.R.W. tube duly powder coated. The ends are fitted with ABS moulded end caps. TIE MEMBER: It is the connecting beam assy. which holds the two side frames to each other. 2 nos. tie members are used to connect the side frames. The tie-member is made of MS. E.R.W. tube 40mmx40mm 2mm thick duly powder coated. The seat/back assemblies are mounted on the tie- member. L bracket of 6mm thick steel connects the back to the tie member assembly. Seat foam is of 45 +/-5 Kg/m3 and back foam is of 32 +/-5 Kg/m3 with hardness of 25+/-2 on Hampden m/c. at 25% compression of the foam. Seat size 52cm wideX50cm deep and back size 52 cm wide and 60cm high. Back of the sofa flexes for additional comfort 1 seater –601mmWX700mmDX 810mmH, 3 seater –1640W x 700D x 785 H cm

3 seater Steel chair Cross Beammade of MS ERW rectangular black powder coated Tube of 80 x 40 x 2 mm Leg & arm rest chrome plated made of cold rolled steel. Arm rest & leg assembled to the cross beam with M10 x 100 mm bolts. Seat & back 1.6mm thick powder coated perforated shell of cold rolled MS Sheet. Side Bar of chrome plated solid steel 30 x 12 mm (DIN 174) with flunting & plastic insert .The shell is assembled on the cross beam with help of M8 Bolts The overall dimension is 1608mm (L) x 695mm (H) x 555mm (D), Seat Height : 405mm

Centre Table of size 1200W x 600D x 378H built with the extremely durable rubberwood, the table can hold weight up to 25kgs. With a very suitable Cappuccino color, the table will complement any style of décor. The tapered legs provide stable support. It’s free of flaws design can accommodate your books, magazines, laptop and coffee mugs, all at once. The well-thought-out dimensions of the table make it easier to position it anywhere in the house

Principal chair: The seat is made up of 1.4± 0.1 chick hot - press 4 plywood upholstered with fabric and moulded polyurethane foam. It has a seat depth adjustment of 5.0±0.3 cm integrated in the seat through a sliding mechanism. SEAT SIZE: 50.0cm (W)x 49.0cm(D).The Back is injection moulded in Glass filled Polyamide which is upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 6.0±0.1cm.BACKSIZE: 50.0cm(W) x68.0 cm(H).The polyurethane foam for seat is of density 55± 5kg/m3. It is made of glass filled Polyamide arm structure with PU arm top and height adjustment of 7.0 ±0.5cm.The arm top has swivel and To-For movements. To-for movement is 6.0± 0.5cm.The inner tube of armrest is chrome plated. The mechanism is designed with the following features:• 360° revolving type.• Centre tilt Synchro• 3 position (including upright lock) giving option of variable tilt angle to the chair with anti shock feature. The Headrest is injection moulded din Glass Filled Polypropylene which is upholstered with foam and fabric has an adjustment of 6.0± 0.1cm & its assembled over the Full back chair. The pneumatic height adjustment is chrome plated with an adjustment stroke of 9.0 ± 0.3cm.The pedestal is High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal is 65.0±0.5 cm P.C.D. The twin wheel castors are injection moulded in black Glass filled polyamide having 6.0±0.1cm wheel Diameter. The Chrome plated tubular frame is made of Día2.8±0.03cm x0.2±0.02 cm the M.S. Round tube. The frame is fitted with plastic caps made of injection moulded glass filled Polypropylene. -75(W)* 75(D)* 115-130(H)* 44.5-53.5(SH).

Computer Chair with seat and back are made uo injection moulded high impact strenght polypropylene polymer compound with indoor graade UV Resistance.The tubular weled frame is made from Dia2.22 +/- 0.03cmx 0.12+/- 0.0128 cm and 3.5+/- 0.03 cm x 0.12+/- 0.0128 am stainless Steel 202 grade tube.The tube are buff polished to give shiny finish. cm. The Shoes are made of high impact strenght polypropylene polymer. compond with indoor grad UV Resistance and pressed fitted with tubularfram. SIZE : (W)52.5cm*(D)55.8cm*(H)84.5cm* (seat H) 45.0 cmSeat Size 52.5cm(W)*53.2 cm(D) Back Size 51.6 cm(W)*40.5 cm (H).

Office Chair Mid back pneumatic height adjustment cushioned revolving chair made up of 1.2cm thick hot pressed ply wood seat & back upholstered with fabric with moulded polyurethane foam together with moulded ABS seat & back integral skin polyurethane with reinforced with M.S. Insert. The tilt mechanism adjustment upright locking, 360 degree revolving type fitted with 05 nos. twin wheel castor dia 5 cm.

Conference Table of 30 Seater -Capacity shall be an eco-modular conference table enables various configurations to suit different conference rooms. It is made of particle board and has wire management facilities for uncluttered wiring. It has profiled legs with twin colored modesty for better looks, Double 1350.0Wx 600.0Dx 750.0H, Work surface Top thickness is 25mm PLB with PVC beading allover, Legs Modesty Wire Manager Made from 18mm thick PLT having curved profile.Made from PLT (Prelaminated Twin) boards 18mm thick in two shades. A Wire Manager running along the width of desk fitted on the modesty Panel from Inside.

Corner Table of size 530W x 450D x 450H built with the extremely durable rubberwood, With a very suitable Cappuccino color, the table will complement any style of décor. The tapered legs provide stable support. It’s free of flaws design can accommodate your books, magazines, laptop and coffee mugs, all at once. The well-thought-out dimensions of the table make it easier to position it anywhere in the house.

File cabinet with 4 Drawer Width: 470mm, Height: 1320mm, Depth: 620mm , Rigid KnockDown Construction, Material:- Top, Side & Drawer Frontmade from0.7mm thk **CRCA, Drawer- Inside Cover, Side Back Side made from0.6mmthk **CRCA, Back, Bottom, Drawer Bottommade from 0.5mmthk **CRCA, **CRCAsteel confirming to IS 513, Grade-D, Label Holder- Snap on type plastic label holder on Drawer Fronts, Locking & anti-tipping arrangement- Centralized lockingwith CamLock& having antitipping arrangement to ensure that when one ,drawer is opened for use, it does not allow other drawers to be opened, finish- Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).

Fire proof Cabinet shall be designed to protect the contents (paper media documents) against the fire hazard.Shell: The external shell of the cabinet shall be of steel of minimum 2 mm thick and internal shell of steel of 1.6 mm thick, both conforming to IS 513. Further fortified by suitable in-situ insulating fire-resistant barriers to meet the required protection. The overall protection to the contents shall be minimum 70 mm on all six sides. Door: The external door of the cabinet shall be of steel of minimum 2 mm thick conforming IS 513 and further fortified with hard plate over the lock for burglary protection and in-situ insulating fire-resistant barrier material to meet required fire protection. Bolt work: The door shall be secured by four way locking mechanism / Bolt work with minimum 8 moving shooting bolts of 20 mm diameter. Door & Body Fitment: The door fits in the cabinet having tongue and groove construction that stops hot gases and high temperature to pass through and withstand temperature up to 1010 deg.C. Locking: The FRRC shall be equipped with a dual control high precision key lock of minimum six levers. The Lock body shall be of Zinc Alloy and the Levers in the lock shall be of Brass conforming to IS 410. There shall not be any dummy lever in the lock. The storage capacity shall be minimum 650 Liters with minimum usable internal sizes in mm as 1620 (h) x 670 (w) x 599 (d).The cabinet shall be provided with minimum four nos. adjustable shelves.

Steel Almirah of size 1981 x 916 x 486 MM multi bend construction and inter locking design and full length over apping doors and sides. Three-way bolting mechanism. Spot welding & CO2 welding. Anticorrosion treated components, oven baked powder coating process. Material thickness 0.9mm.Top, Bottom,LH & RH sides and back material thickness= 0.9mm,Removable RH & LH main door with stiffeners material thickness= 0.9mm, 4 adjustable shelves of thickness= 0.8mm

Steel Rack of size 6'x36"x18" with Six Shelves Prime quality CRC sheet conforming to IS 513D/10748/5986. The pitches of the slots at 19.05 mm, Panel/Shelves: 6 Bnd bending process of 905L x 448D of load capacity 80 Kgs. UDL Max Per shelf. Shelf Material- 0.8 mm Thick MS Sheet Conforming to Commercial Quality CR-1, Grade 340 of IS 513, Angle Posts Material and size-Rolled steel angle posts of 40 X 40 X 1.8 mm, M S Sheet Thickness of Shelves and Back (Minimum) in mm-0.8, Paint-Powder coated with Lead Free Paint.

Computer Table of Size-600W x 450D x 750H mm Compact and easy to use . Top made-up of 1.5 cm Medium Density Fiber. All the other panels are made of Particle board. Vacuum lamination of pvc has been done on the table to surface. 0.4mm lapping is used for all the other panels

Office Table made of MS ERW round tube dia 25.4 x 1.2mm thick with 18 mm thick Pre Laminated top size 1365 X 680 X 735 (Approx.) with both side drawer unit one side three drawers & another side two drawers made of .5mm thick CRCA sheet mild steel, All steel components have powder coated paint fitted with both side drawer lock

Principal Table Main desk of size 1800 x 900 x 740, ERU of size 1550 x 450 x 705 made up of TOP-25 MM THICK PLAIN PARTICLE BOARD (PPB) CLAD WITH 0.6MM THICK POST FORMED LAMINATE AND 1MM THICK BACKING LAMINATE (BDL). FLAT EDGE DULY SEALED WITH 2MM THICK PVC BEADING., MODESTY-18MM THICK PLAIN PARTICLE BOARD (PPB) CLAD WITH 1.0MM THICK DECORATIVE LAMINATE (DL) ON BOTH SIDES. EDGE SEALED WITH 2MM THICK PVC BEADING WITH 01 NO. 3 DRAWERS FREE STANDING PEDESTAL.

Dressing Table of size 460W x 486D x 1710H mm , Mirror W x H: 362 mm x 1156 mm dressing table comes with a long mirror, two storage drawers, and a stool. Available in wenge color, the dresser is crafted from good quality MDF wood, making it sturdy and lasting. The shelves of this stylish dressing table can be used to keep items like perfume bottles, hair products, and medicines, for that clutter-free look. The stool, also wenge color with an orange colored cushion, offers comfortable seating, while the full length mirror is perfect to dress up, and check your overall ensemble.

Auditorium Chair SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2±0.1 cm. thick hot-pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam. The back is, flexing type.Back Size-47.0 cm. (W) x 51.0 cm. (H), Seat Size-47.0 cm. (W) x 47.0 cm. (D). 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression.3. ARMRESTS :The one-piece armrests are made of black integral skin polyurethane foam with 50-70 Shore hardness and reinforced with M.S. insert. The armrests are scratch and weather resistant.5. UNDERSTRUCTURE ASSEMBLY: It is made of Dia. 2.54±0.03cm. x 0.2±0.016cm. thk. M.S.E.R.W. tube with connecting strips made of 0.5 ± 0.05 cm. thk. HR Steel welded to it for holding the seat. The assembly is powder coated ( DFT 40-60 microns ).The auditorium chair is designed to get mounted/grouted on floors with flooring specification as mentioned in flooring pre-requisite Godrej doc-no: STG 129368.Overall Width-57.0, Depth-57.0, Height-86.0, Seat Height-44.0 cm.

Notice Board with size 4' X 3' Surface Material-woolen felt / fabric in various colours,Core material-9 mm thick soft board,Backing Material-0.62 mm to 0.82mm thick laminate sheet with extra melamine surface mix colour OR 0.16 to 0.25 mm thick ISI mark GP sheet,Aluminium frame-Anodized 5 microns extruded aluminium section designation 63400 as per IS:1285- 2002 - 16 mm thickness

Signage

SEPTIC TANK

FINAL SUM

Description

Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Earth work in excavation over areas (exceeding 30 cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m ; disposed earth to be levelled and neatly dressed.All kinds of soil

Extra for every additional lift of1.5m or pan thero of in all kind of soil etc all complete job

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work M-25

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer- in-Charge.

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1:3:6 (1 Cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level. 1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level:1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete:All work upto plinth level

Walls columns, pillars, posts cind struts

Beams, planth beams, girders, bressumers, cantilevers, Suspended floors lintels roofs and staircases including spiral cum 5677.20 staircases shelves etc

Add or deduct for providing richer or leaner mixes respectively at all floor levels.Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete All work upto plinth level + Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C.

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete All works above plinth level upto floor V level Walls columns, pillars, posts cind struts

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete All works above plinth level upto floor V level Beams, planth beams, girders, bressumers, contilevers, Suspended floors lintels roofs and staircases including spiral staircases, shelves etc.

Centring and shuttering including strutting, propping etc. and removal of form for.

Foundation

Suspended floors

Shelves

Lintels, beams, plinth bams,

Columns

Stairs

Chajjas

Edge of Slab

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

TMT-500-8mm dia

TMT-500-10mm dia

TMT-500-12mm dia

TMT-500-16mm dia

TMT-500-20mm dia

TMT-500-25mm dia

Brick work with bricks of class designation 100A in foundations and plinth in :Cement mortar 1:6 (1 cement: 6 coarse sand )

Brick work with fly ash bricks as per IS 12894 (2002) & IS 3495 in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand )

Brick work with fly ash bricks as per IS 12894 (2002) & IS 3495 in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand ) + Extra tor Brick work in superstructure above plinth level upto floor V cum

Brick work with fly ash bricks as per IS 12894 (2002) & IS 3495 in foundations and plinth in : Cement mortar 1.:4 (1 cement: 4 coarse sand ) + Extra tor Brick work in superstructure above plinth level upto floor V cum

Brick work with bricks with fly ash bricks as per IS 12894(2002) & 3495 in foundation and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand)

Providing 12 mm cement plaster of mix: 1:6(1 cement: 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix. 1:5(1 cement: 5 coarse sand )

15 mm cement plaster on rough side of single or half brick wall of mix. 1:6(1 cement: 6 coarse sand )

15 mm cement plaster on rough side of single or half brick wall of mix.1:4(1 cement: 4 coarse sand )

6 mm cement plaster to ceiling of mix : 1:4(1 cement: 4 coarse sand)

Providing 12 mm thick plaster (1:3) with a floating coat of neat cement

15 mm cement plaster 1:3 (1 cement: 3 coarse sand ) finished with a floating coat of neat cement on the rough side of single or half brick wall.

Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly. plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications. Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm.

Supplying iron angle of Size 50x50x6mm for using barbed wire as per suitable size and shape

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Distempering with oil bound washa ble distemper of approved brand and manufacture to give an even shade . New work (two or more coats ) over and including priming coat with cement primer

Applying priming coat with ready mixed zinc chromate yellow primer of approved brand and manufacture on steel galvanized iron/steel work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: incliding priming coat

Drilling 6mm Dia. In M.S. angle iron for fixing of staples etc. as per building specification and direction of E/l.

Labour for cutting of M.S. angle iron post to required length, one end splitted as fish tailed in a length of 150mm complete as per building specification and direction of E/l.

Labour for fitting and fixing barbed wire fencing in six rows horizontal up to a height of 1.85m and two diagonals including fixing of post in cement concrete at 2.5m centres including cost of staples (but excluding the cost of cement concrete, angle, iron post, its cutting and making holes, nuts & bolts) all complete as per building specification and direction of E/l.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab upto 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for providing opening of required size & shape for wash basins/kitchen sink in kitchen platform. Vanity counters and similar location in marble/granite/stone work including necessary holes for pillar taps etc. including rubbing,moulding and polishing of cut edges etc. complete.

Kota stone slab flooring over 20 mm (average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . Base with 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand 20 to 25 mm thick -

Kota stone slabs 20 mm thick in risers of steps skirting. Dado & pillars laid on 12 mm (average (thick cement mortar 1:3 (1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Details of cost for 10 sqm

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete. Size 600 X 1200

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

38 mm thick parquet (wood block) flooring of 1st class teak wood laid over 25 mm thick levelling layer of cement concrete 1:2:4(1 cement:2 coarse sand:4 store aggregate 10 mm nominal size) to be paid separately coated with a thin layer of hot bitumen (blown type) @ 2.45 kg per sqm. including fixing blocks in position after dipping in hot bitumen (blown type) upto half depth,planed,levelled smooth and finished complete

Providing& fixing inpositionPhenol bondedBamboowood flooring with planks of sizes 14mm thick, minimum 1800mm length and minimum100mmwide, inapprovedcolour, textureandfinish,having PerformanceAppraisalCertificate(PAC) issuedbyBuildingMaterials& TechnologyPromotionCouncil (BMTPC). The flooringshall be fixed withtongueandgrooveinterlockingsystem,withunderlaymentof4mm thickexpandedpolythylenefoamsheetshavingdensity40kg/cum,over preparedsurfacewithnecessaryquarterroundplanksofsize1900mm x18mmanddoorreducerofsize1900mmx44mm,whereverrequired. Thebomboowoodplanksshallhaveminimumdensityof1000Kg/cum &minimumHardness 1000Kgf. withEco friendlyUV coating, all complete as per direction of the Engineer in-char

Providing& fixing inpositionPhenol bondedBamboowood inwall skirtingwithplanksof sizes14mmthick, 1900mmlength (minimum) and 85mmwide(minimum), in approved colour, texture and finish, havingPerformanceAppraisal Certificate (PAC) issued byBuilding aterials&TechnologyPromotionCouncil (BMTPC).Theskirtingshall fixedwithSSscrews&rawlplugs,overunderlaymentof4mmthick, expandedpolyethylene foamsheetshaving40kg/cumdensityover prepared surface. The bomboowood planks shall haveminimum densityof 1000Kg/cum&minimumHardness 1000Kgf. withEco friendlyUVcoating, all completeasperdirectionof theEngineer in charge

Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile C

Providing and fixing 35 mm thick factory made laminated veneer lumberdoor shutter conforming to IS : 14616 and TADS 15:2001 (Part B),including ISI marked M.S.pressed butt hinges bright finished of requiredsize with necessery screws, all complete as per directions of Engineer-in-Charge and panelling with panels of:

30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-incharge.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately):Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing oxidised M.S. double acting spring hinges with necessary screws etc. complete

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having water absorption less than 0.5% and conforming to IS: 15622, of approved make in all colours and shades in outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required In gratings, frames, guard bar, ladders, railings, brackts. gates & similar works..

Providing and fixing glazing in aluminium door, window,ventilatorshutters and partitions etc. with EPDM rubber / neoprene gasketetc. complete as per the architectural drawings

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.).

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots.nuts locking arrangement stoppers handies including applying a priming coat of approved steel primer.

Supplying and fixing-rolling shuters of approved make.made of required size of M.S.Iaths interlocked together through their intire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arragements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

Providing and fixing ball bearing for rolling shutters

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of glass panes with glazing clips and special metal-sash putty of approved make complete including applying a priming coat of approved steel primer; xcluding the cost of metal beading and other fitting except necessary hinges or pivots as required

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing bright finished brass night latch of approved quality including necessary screws etc. complete

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete 25 mm dia metre

Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etc. complete.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (overall area of door shutter to be measured)

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete: 2nd class teak wood

Providing and fixing bright finished brass peg stays 300 mm long of minimum weight 330 gms.to side hung steel windows with necessary welding and machine screws etc. complete

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings complete jncluding applying a priming coat of approved steel primer.

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing on wall face unplastidsed- PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised- PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Coupler

110 mm bend

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing '@ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge. With fully perforated 12 mm thick micro tegular edged or 10 mm thick square edged GRG false ceiling tiles

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's 15 mm thick fully With perforat d square/butt edge light weight calcium silicate panels/ tiles

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished welded type tubes

Providing and fixing 15 cm wide 45 cm over all semi circular plain G.S. sheet gutter with iron brackets 40x3 mm size bolts, nuts and washers etc. including making necessary connections with rain water pipes complete. 0.80 mm thick with zinc coating not less than 275 gm/m2

Providing and fixing thermal insilation with resin bonded fiber glass wool

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with G.I.J. or L hooks . Bolts and nuts 8 mm dia. G. 1. limpet and bitumen washers complete. . 0.63 mm thick with zinc coating not less than 275 gm/m2

Extra for providing and fixing wind ties of 40x6mm flat iron section.

Extra for making chamfered edges of beading Thermal Insulation of roofing with Expanded polystyrene fixed with suitable adhesive to the false ceiling as per the directions of the Engineer-in charge With Type N-Normal

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water

Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade:Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacture's specifications including appropriate priming coat, preparation of surface, etc. complete

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2)For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25-0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors,embedding in floors as required and making good

Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer in-charge

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications,drawings and direction of Engineer-in-charge complete.

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/ sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/450N/5 cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane.

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100%polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation

Grading roof for water proofing treatment withCement concrete 1:2:4(1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing, Fixing, Testing and Commissioning of ROOFING Make: TATA BLUESCOPE Providing, fixing, testing and commissioning of roofing made of TATA BLUESCOPE factory-rolled colour-bond LYSAGHT KLIP-LOK 700 concealed profile system sheeting with nominal 43 mm crest depth, 700 mm effective cover width, with ribs at a pitch of 233 mm centre to centre along with stiffeners perpendicular to ribs for strength. The feed material shall be manufactured out of nominal 0.5 mm thickness with allowable thickness tolerance of ±0.04 mm. Total coated thickness (TCT) shall be high-strength steel with minimum 550 MPa yield strength, metallic hot-dip coated with Aluminium-Zinc alloy (55% Aluminium, 45% Zinc) as per AS 1397 – Zincalume AZ 150 (minimum 150 g/sq m total on both sides). The sheet shall have super polyester colour-bond XRW quality paint coat as per AS/NZS 2728 Class 3 of Tata BlueScope Steel make. The paint coating shall have a total thickness of nominal 35 microns, comprising: Nominal 20 microns exterior coat on top surface Nominal 5 microns reverse coat on back surface Over nominal 5 microns primer coat on both surfaces All complete as per manufacturer’s specifications and directions of the Engineer-in-Charge.

Providing, Fixing, Testing and Commissioning of FLASHING / RIDGE Make: TATA BLUESCOPE Providing, fixing, testing and commissioning of flashing/ridge made of TATA BLUESCOPE colour-coated (COLORBOND) steel of 0.50 mm TCT Feed material shall be manufactured out of nominal 0.5 mm thickness with allowable thickness tolerance of ±0.04 mm, high-strength steel with minimum 550 MPa yield strength, metallic hot-dip coated with Aluminium-Zinc alloy (55% Aluminium, 45% Zinc) as per AS 1397 – Zincalume AZ 150 (minimum 150 g/sq m total on both sides). The material shall have super polyester colour-bond XRW quality paint coating as per AS/NZS 2728 Class 3 of Tata BlueScope Steel make. Total paint coating thickness shall be nominal 35 microns, comprising: Nominal 20 microns exterior coat on top surface Nominal 5 microns reverse coat on back surface Over nominal 5 microns primer coat on both surfaces All complete as per manufacturer’s specifications and directions of the Engineer-in-Charge.

Signage

Wall / Door Mounted (300 x 420 mm)

Wall / Door Mounted (150 x 400 mm)

Wall / Door Mounted (155 x 210 mm)

Ceiling Suspended

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mmsand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and makinggood the walls andlevel white P.V.C. flushing cistern, including flush pipe, withmanually controlled device (handle lever) onforming to IS : 7231, with all fittingsand floors wherever required : White Vitreous china Orissa pattern W.C. pan ofsize 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required 510x1040 mm bowl depth 250 mm

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 40 mm dia

Providing and fixing in position 25mm diameter mosquito proof coupling of approved municipal design

Providing and fixing C.I. sluice valves (with cap) complete with bolts,nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :100 mm diameter Class I

Providing and fixing mirror of superior glass (of approved quality) and of equired shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Providing and fixing 600x120x5 mm glass shelf with edges round off,supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete

100 mm dia Sand cast iron S&S pipe as per IS : 1729

Providing and fixing PTMT Bottle Trap for Wash basin and sink Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shape with brac et of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms

Providing and fixing PTMT Waste Coupling for wash basin and sink,of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe.

Providing and fixing uplasticised PVC connection pipe with brass ions : 15 mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe ithclamps at 1.00 m spacing. This includes jointing of pipes & fittingswith one step CPVC solvent cement and testing of joints complete asper direction of Engineer in Charge

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with 3clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.80 mm dia. Nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) :

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15 mm nominal bore

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.

Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand 6 graded stone aggregate 20 mm nominal size) including disposal of malba.

inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with mframe (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :Inside dimensions 455x610 mm and 45 cm deep for single pipe line :

Supplying and fixing C.I. cover without frame for manholes :560 mm diameter C.I. over (heavy duty) the weight of the cover to be not less than 108 kg.

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Providing and fixing on wall face unplasticised -PVC molded tings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking gement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality:EHD-35:Circular shape 560 mm internal diameter

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal\ size) as per standard design

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. 300 mm dia.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. 300 mm dia.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths,as per direction of Engineer -in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.150 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Supplying and fittings 2 HP Submersible water pump with starter cables etc. all necessary fitting etc. all complete jobs.

Supplying, Installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

Fabricating, Supplying, Erection, Testing and commissioning of Electrical control panel cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet,compartmentalised with hinged lockable doors, dust and vermin proof, coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and outgoings, suitable for operation on 415V, 3 Phase, 50Hz Ac supply with enclosure protection class IP42 as required:

Providing, laying , testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS:1239 including welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gasket etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required:

Meters

Meters

Meters

Meters

Meters

Supply and fixing single headed internal hydrant valve with instanteneous Gunmetal/Stainless steel coupling of 63mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type-A) with blank Gunmetal/Stainless steel cap and chain as required.

Supply,fixing,testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS:13095 of following size as required.

Providing, installation, testing and commissioning of non-return valve of following sizes conforming to IS:5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required.

Providing , installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6mm thick stainless steel, Grade 304, sheet with 3mm dia holes with stainless steel flange.

Supplying and fixing 63mm dia, 15m long RRL hose pipe with 63mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 ( Type-A) as required:

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20mm nominal dia water hose thermoplastic ( Textile reinforced) type-2 as per IS:12585 20mm nomonal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipments on wall. " Connections from riser with 25mm dia stop gunmetal valve & M.S Pipe and socket.

Supplying and fixing 63mm dia gun metal short branch pipe with 20mm nominal diameter size nozzle confirming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required.

Supplying and fixing for Fire Brigade Connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as required for suitable dia MS pipe connection conforming to IS 904 as required.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Meters

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following,complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

Supply, laying & connecting with Diesel Engine Fire Pump Electrical Panel at ground level with 3.5 core x 10 sq. mm. armored aluminum cable 1.1 kv grade.

Supply,Installation,Testing and commissioning of smoke detector with built in LED and mounting base with complete with all connections etc. as required.

Supply,Installation,Testing and commissioning of manual call box ABS in surface recessed complete with glass and push button etc as required.

Supply,Installation,Testing and commissioning of response indicator on surface having two LED metallic cover complete with all connection etc. as required.

Supply,Installation,Testing and commissioning of fire alarm sounder with facility to make announcement, mounted in ABS box with hinge cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supply,Installation,Testing and commissioning of sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault fire condition and all other standarad facilities as per IS:2189 with mimic diagram all area zone covered, complete with all connections, interconnections as required.

Supplying and laying of 2x1.5 sq.mm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of cross linkable ethelene propyline rubber (EPR) insulation and LSZH inner bedding, steel wire armounting & LSZH outer sheath complete as required, (rate of area protected in sq.mm)

M.S. hose cabinet with door fabricated from 16 g M.S. sheet with full glass door and locking arrangement, suitable to accommodate 1 Hydrant landing valve, 1 fire hose reel, 1nos.15m long 63mmdia hose,1-branch pipe, The door shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including suitably mounted on a raised masonry platform as required (Approx. size 1.2m x 2.1m). For internal hydrants.

ISI marked (IS:2878) Portable fire Extinguisher, Carbon-dioxide type flat base including valve, discharge hose of not less than 10 mm dia. 1m long & complete in all respects including initial fill with C02 gas confirming to IS:307-1966 filled to a filling ratio of not more than 0.667of not more than 0.667and wall suspension bracket.

'ABC' stored pressure type Dry Chemical Powder (Mono-Ammonium Phosphate ) 6 kg fire extinguisher with fixing hangers, hose, brackets, screws to required size etc., complete as per IS:14609.

Door Frame Metal Detector

Hand Held Metal Detector

Office Table made of MS ERW round tube dia 25.4 x 1.2mm thick with 18mm thick Pre Laminated top size 1199 X 590 X 735 mm with one side one drawer unit made of .5mm thick CRCA sheet mild steel, All steel components have powder coated paint fitted with lock.

3 Seater Sofa The side frame assembly made of 38mm Dia 2mm thick is fitted to the two ends of the connecting beam assembly to form the leg-cum-arA/Rest assembly. It is made of a MS. E.R.W. tube duly powder coated. The ends are fitted with ABS moulded end caps. TIE MEMBER: It is the connecting beam assy. which holds the two side frames to each other. 2 nos. tie members are used to connect the side frames. The tie-member is made of MS. E.R.W. tube 40mmx40mm 2mm thick duly powder coated. The seat/back assemblies are mounted on the tie- member. L bracket of 6mm thick steel connects the back to the tie member assembly. Seat foam is of 45 +/-5 Kg/m3 and back foam is of 32 +/-5 Kg/m3 with hardness of 25+/-2 on Hampden m/c. at 25% compression of the foam. Seat size 52cm wideX50cm deep and back size 52 cm wide and 60cm high. Back of the sofa flexes for additional comfort 1 seater –601mmWX700mmDX 810mmH, 3 seater –1640W x 700D x 785 H cm

3 seater Steel chair Cross Beammade of MS ERW rectangular black powder coated Tube of 80 x 40 x 2 mm Leg & arm rest chrome plated made of cold rolled steel. Arm rest & leg assembled to the cross beam with M10 x 100 mm bolts. Seat & back 1.6mm thick powder coated perforated shell of cold rolled MS Sheet. Side Bar of chrome plated solid steel 30 x 12 mm (DIN 174) with flunting & plastic insert .The shell is assembled on the cross beam with help of M8 Bolts The overall dimension is 1608mm (L) x 695mm (H) x 555mm (D), Seat Height : 405mm

Centre Table of size 1200W x 600D x 378H built with the extremely durable rubberwood, the table can hold weight up to 25kgs. With a very suitable Cappuccino color, the table will complement any style of décor. The tapered legs provide stable support. It’s free of flaws design can accommodate your books, magazines, laptop and coffee mugs, all at once. The well-thought-out dimensions of the table make it easier to position it anywhere in the house

Principal chair: The seat is made up of 1.4± 0.1 chick hot - press 4 plywood upholstered with fabric and moulded polyurethane foam. It has a seat depth adjustment of 5.0±0.3 cm integrated in the seat through a sliding mechanism. SEAT SIZE: 50.0cm (W)x 49.0cm(D).The Back is injection moulded in Glass filled Polyamide which is upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 6.0±0.1cm.BACKSIZE: 50.0cm(W) x68.0 cm(H).The polyurethane foam for seat is of density 55± 5kg/m3. It is made of glass filled Polyamide arm structure with PU arm top and height adjustment of 7.0 ±0.5cm.The arm top has swivel and To-For movements. To-for movement is 6.0± 0.5cm.The inner tube of arA/Rest is chrome plated. The mechanism is designed with the following features:• 360° revolving type.• Centre tilt Synchro• 3 position (including upright lock) giving option of variable tilt angle to the chair with anti shock feature. The Headrest is injection moulded din Glass Filled Polypropylene which is upholstered with foam and fabric has an adjustment of 6.0± 0.1cm & its assembled over the Full back chair. The pneumatic height adjustment is chrome plated with an adjustment stroke of 9.0 ± 0.3cm.The pedestal is High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal is 65.0±0.5 cm P.C.D. The twin wheel castors are injection moulded in black Glass filled polyamide having 6.0±0.1cm wheel Diameter. The Chrome plated tubular frame is made of Día2.8±0.03cm x0.2±0.02 cm the M.S. Round tube. The frame is fitted with plastic caps made of injection moulded glass filled Polypropylene. -75(W)* 75(D)* 115-130(H)* 44.5-53.5(SH).

Computer Chair with seat and back are made uo injection moulded high impact strenght polypropylene polymer compound with indoor graade UV Resistance.The tubular weled frame is made from Dia2.22 +/- 0.03cmx 0.12+/- 0.0128 cm and 3.5+/- 0.03 cm x 0.12+/- 0.0128 am stainless Steel 202 grade tube.The tube are buff polished to give shiny finish. cm. The Shoes are made of high impact strenght polypropylene polymer. compond with indoor grad UV Resistance and pressed fitted with tubularfram. SIZE : (W)52.5cm*(D)55.8cm*(H)84.5cm* (seat H) 45.0 cmSeat Size 52.5cm(W)*53.2 cm(D) Back Size 51.6 cm(W)*40.5 cm (H).

Office Chair Mid back pneumatic height adjustment cushioned revolving chair made up of 1.2cm thick hot pressed ply wood seat & back upholstered with fabric with moulded polyurethane foam together with moulded ABS seat & back integral skin polyurethane with reinforced with M.S. Insert. The tilt mechanism adjustment upright locking, 360 degree revolving type fitted with 05 nos. twin wheel castor dia 5 cm.

Conference Table of 30 Seater -Capacity shall be an eco-modular conference table enables various configurations to suit different conference rooms. It is made of particle board and has wire management facilities for uncluttered wiring. It has profiled legs with twin colored modesty for better looks, Double 1350.0Wx 600.0Dx 750.0H, Work surface Top thickness is 25mm PLB with PVC beading allover, Legs Modesty Wire Manager Made from 18mm thick PLT having curved profile.Made from PLT (Prelaminated Twin) boards 18mm thick in two shades. A Wire Manager running along the width of desk fitted on the modesty Panel from Inside.

Corner Table of size 530W x 450D x 450H built with the extremely durable rubberwood, With a very suitable Cappuccino color, the table will complement any style of décor. The tapered legs provide stable support. It’s free of flaws design can accommodate your books, magazines, laptop and coffee mugs, all at once. The well-thought-out dimensions of the table make it easier to position it anywhere in the house.

File cabinet with 4 Drawer Width: 470mm, Height: 1320mm, Depth: 620mm , Rigid KnockDown Construction, Material:- Top, Side & Drawer Frontmade from0.7mm thk **CRCA, Drawer- Inside Cover, Side Back Side made from0.6mmthk **CRCA, Back, Bottom, Drawer Bottommade from 0.5mmthk **CRCA, **CRCAsteel confirming to IS 513, Grade-D, Label Holder- Snap on type plastic label holder on Drawer Fronts, Locking & anti-tipping arrangement- Centralized lockingwith CamLock& having antitipping arrangement to ensure that when one ,drawer is opened for use, it does not allow other drawers to be opened, finish- Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).

Fire proof Cabinet shall be designed to protect the contents (paper media documents) against the fire hazard.Shell: The external shell of the cabinet shall be of steel of minimum 2 mm thick and internal shell of steel of 1.6 mm thick, both conforming to IS 513. Further fortified by suitable in-situ insulating fire-resistant barriers to meet the required protection. The overall protection to the contents shall be minimum 70 mm on all six sides. Door: The external door of the cabinet shall be of steel of minimum 2 mm thick conforming IS 513 and further fortified with hard plate over the lock for burglary protection and in-situ insulating fire-resistant barrier material to meet required fire protection. Bolt work: The door shall be secured by four way locking mechanism / Bolt work with minimum 8 moving shooting bolts of 20 mm diameter. Door & Body Fitment: The door fits in the cabinet having tongue and groove construction that stops hot gases and high temperature to pass through and withstand temperature up to 1010 deg.C. Locking: The FRRC shall be equipped with a dual control high precision key lock of minimum six levers. The Lock body shall be of Zinc Alloy and the Levers in the lock shall be of Brass conforming to IS 410. There shall not be any dummy lever in the lock. The storage capacity shall be minimum 650 Liters with minimum usable internal sizes in mm as 1620 (h) x 670 (w) x 599 (d).The cabinet shall be provided with minimum four nos. adjustable shelves.

Steel Almirah of size 1981 x 916 x 486 MM multi bend construction and inter locking design and full length over apping doors and sides. Three-way bolting mechanism. Spot welding & CO2 welding. Anticorrosion treated components, oven baked powder coating process. Material thickness 0.9mm.Top, Bottom,LH & RH sides and back material thickness= 0.9mm,Removable RH & LH main door with stiffeners material thickness= 0.9mm, 4 adjustable shelves of thickness= 0.8mm

Steel Rack of size 6'x36"x18" with Six Shelves Prime quality CRC sheet conforming to IS 513D/10748/5986. The pitches of the slots at 19.05 mm, Panel/Shelves: 6 Bnd bending process of 905L x 448D of load capacity 80 Kgs. UDL Max Per shelf. Shelf Material- 0.8 mm Thick MS Sheet Conforming to Commercial Quality CR-1, Grade 340 of IS 513, Angle Posts Material and size-Rolled steel angle posts of 40 X 40 X 1.8 mm, M S Sheet Thickness of Shelves and Back (Minimum) in mm-0.8, Paint-Powder coated with Lead Free Paint.

Computer Table of Size-600W x 450D x 750H mm Compact and easy to use . Top made-up of 1.5 cm Medium Density Fiber. All the other panels are made of Particle board. Vacuum lamination of pvc has been done on the table to surface. 0.4mm lapping is used for all the other panels

Office Table made of MS ERW round tube dia 25.4 x 1.2mm thick with 18 mm thick Pre Laminated top size 1365 X 680 X 735 (Approx.) with both side drawer unit one side three drawers & another side two drawers made of .5mm thick CRCA sheet mild steel, All steel components have powder coated paint fitted with both side drawer lock

Principal Table Main desk of size 1800 x 900 x 740, ERU of size 1550 x 450 x 705 made up of TOP-25 MM THICK PLAIN PARTICLE BOARD (PPB) CLAD WITH 0.6MM THICK POST FORMED LAMINATE AND 1MM THICK BACKING LAMINATE (BDL). FLAT EDGE DULY SEALED WITH 2MM THICK PVC BEADING., MODESTY-18MM THICK PLAIN PARTICLE BOARD (PPB) CLAD WITH 1.0MM THICK DECORATIVE LAMINATE (DL) ON BOTH SIDES. EDGE SEALED WITH 2MM THICK PVC BEADING WITH 01 NO. 3 DRAWERS FREE STANDING PEDESTAL.

Dressing Table of size 460W x 486D x 1710H mm , Mirror W x H: 362 mm x 1156 mm dressing table comes with a long mirror, two storage drawers, and a stool. Available in wenge color, the dresser is crafted from good quality MDF wood, making it sturdy and lasting. The shelves of this stylish dressing table can be used to keep items like perfume bottles, hair products, and medicines, for that clutter-free look. The stool, also wenge color with an orange colored cushion, offers comfortable seating, while the full length mirror is perfect to dress up, and check your overall ensemble.

Auditorium Chair SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2±0.1 cm. thick hot-pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam. The back is, flexing type.Back Size-47.0 cm. (W) x 51.0 cm. (H), Seat Size-47.0 cm. (W) x 47.0 cm. (D). 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression.3. ARA/RESTS :The one-piece arA/Rests are made of black integral skin polyurethane foam with 50-70 Shore hardness and reinforced with M.S. insert. The arA/Rests are scratch and weather resistant.5. UNDERSTRUCTURE ASSEMBLY: It is made of Dia. 2.54±0.03cm. x 0.2±0.016cm. thk. M.S.E.R.W. tube with connecting strips made of 0.5 ± 0.05 cm. thk. HR Steel welded to it for holding the seat. The assembly is powder coated ( DFT 40-60 microns ).The auditorium chair is designed to get mounted/grouted on floors with flooring specification as mentioned in flooring pre-requisite Godrej doc-no: STG 129368.Overall Width-57.0, Depth-57.0, Height-86.0, Seat Height-44.0 cm.

Notice Board with size 4' X 3' Surface Material-woolen felt / fabric in various colours,Core material-9 mm thick soft board,Backing Material-0.62 mm to 0.82mm thick laminate sheet with extra melamine surface mix colour OR 0.16 to 0.25 mm thick ISI mark GP sheet,Aluminium frame-Anodized 5 microns extruded aluminium section designation 63400 as per IS:1285- 2002 - 16 mm thickness

Supplying and stacking of good earth at site including royalty but excluding carriage (earth measured in stacks will be reduced by 20 % for payment)

Supplying and stacking at site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)

Mixing earth and sludge or manure in proportion specified or directed.

Spreading of sludge, dump manutre or/and good earth in required thickness (Cost of sludge, dump manure or/and good earth to be paid separately)

Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free form weeds and fit for moving including supplying good earth if needed.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20 % 1 part of stacked volume of manure after reduction by 8 % ) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure sludge or extra good earth if needed to be paid for separately)

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8 :1 (8 parts of stacked volume of earth after reduction by 8% ) flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Good Earth (1 km katcha + 2 km pucca)

Manure (1 km katcha + 2 km pucca)

DESCRIPTION

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc.as required

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate/ switch box including connections but excluding modular plate etc. as required.

Wiring for twin control light point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box etc as required.

Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

Metre

Metre

Metre

Metre

Metre

Supplying and fixing metal/ PVC box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and drawing following pair 0.5 sq. mm FR PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/ recessed PVC conduit as required.

meter

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

meter

Supplying and fixing electronic musical call suitable for single phase, 230 volts complete bell as required.

Supplying and fixing 2 pin, 5/6 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box but excluding modular plate as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed PVC conduit as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 nos. 5 pin 5/6 amps modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc. as required.

Supplying and fixing following way, horizontal type three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus - bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 amps modular socket outlet and 25 amp modular SP MCB 'C' curve, including connections, painting etc. as required.

Supply and fixing of fabricated Electrical control panel of cubical construction, floor/wall mounted type, fabricated out of 16 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator and complete in all respect etc and panel manufactures must be approved by CPRI. (But without RYB inicator, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears etc.)

Supply of Copper Strip

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required.

Providing and fixing following capacity four pole ON-load/ panel mounted changeover switches inside the existing cubical panel board including drilling holes in cubicle panel, making connections etc. as required.

Providing chemical/mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth and earth inspection pit etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal/coke and salt as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required.

Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, copper tube, having single prong on top, with 85 mm dia 3 mm thick copper base plate including holes etc. complete as required.

Providing and fixing copper tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For horizontal run)

Providing and fixing copper tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick copper strip, 125 mm long, with 4 nos. of tinned brass bolts, nuts, chuk nuts and spring washers etc. complete as required.

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

Metre

Metre

Metre

Metre

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Metre

Metre

Metre

Providing , laying and fixing of following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep) and re-filling etc as required.

Metre

Supply and installation of regular/standard model A.C. ceiling fan of 1400 mm sweep with service value (CM/MM) minimum 4.10, Air delivery minimum 245 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required.

Supply and installation of 400 mm, 230 V A.C. wall/cabin fan including fixing the bracket, making connection, testing, commissioning etc as required.

Supplying and fixing recess mounted following types LED downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required.

Supplying and fixing surface mounted following types LED downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing following types LED Flood light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, IP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

Supplying and fixing recess mounted 36 watt LED flat panel (2' X 2') with minimum efficacy 100 lm/w which privides soft light and glare free symmetrical illumination suitable for armstrong/grid ceiling and integrated electronic driver etc directly on false ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing 2'X9 watt LED batten with minimum efficacy 100 lm/w in polycarbonate housing and complete with integrated electronic driver etc directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required.

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

Supplying and fixing wall mounted light bracket/ fixture made with polycarbonate suitable for single 9/10 watt LED lamp directly on wall including connections etc as required. ( But without lamp )

Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required.

Supplying and fixing post top / gate light (width 250/300 mm) made up of high grade unbreakable polycarbonate material suitable for upto 20 watt LED lamp including connections and earthing the body etc as required. ( But without lamp)

Supply and erection of 6 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting including 6A 'C' series SP MCB, connector, and suitable size foundation bolts with template as required.(but without pole foundation)

Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, IP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

Providing and making of following sizes octagonal street light pole foundation in reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size ) of specified size including PVC conduit, form work, curing, reinforcement, excavation and refilling etc. as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required.

Meter

Providing and fixing following capacity double pole/ TP&N sheet metal switch disconnector fuse unit in the existing metal panel board with rewireable type fuses including drilling holes in metal panel, making connections etc. as required.

Providing and making steel pole collar with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 stone aggregate 20 mm ) of specified size and shapeincluding form work, plastering if required, curing etc. as required. (volume of pole/pipe not to be deducted)

Providing and fixing carbon dioxide (CO2) type fire extinguishers confirming to IS 2878: 1976 and cylinders fully charged of following capacity.

Supply and fixing of foam fire extinguishers, Portable type 9 lit capacity hanged on wall with bracket complete as required

Supply and fixing safety instruction chart in word duly framed with 5 mm thick glass as required. (approx. front area 1.20 sq. mt.)

Providing of set of 4 Nos. 9.5 Litre capacity GI bucket painted in post office red colour with prior coat of red oxide paint and written with white paint 'FIRE' and mounted on MS angle iron frame with bracket of appropriate size & capacity i/e filling sand etc.

Providing of rubber mat 1 mtr. wide and 12 mm thick to withstand 15 KV dielectric strength as per IS 5424: 1969

Providing of rubber mat 1 mtr. wide and 12 mm thick to withstand 1.1 KV dielectric strength as per IS 5424: 1969

Supply of Hand Gloves 11KV Tested

Supply & fixing of Double Pole Structure( 9 meter PSC) for installation of CT/PT unit alongwith AB Switch, Horn Gap Fuse Set, HT Lighting Arrestor, Channel, earthing, civil work etc as required as per site.

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power H.T. cable with aluminium conductor for working voltage upto 11 KV as required.

Meter

Earth digging by horizontal directional drilling (HDD) method, Laying, termination/Jointing, Erection, Testing & Commissioning of 33 KV grade 3-Core 120 sq.mm XLPE Cable underground using HDPE Pipe complete in all respect along with all accessories, earth

Laying and fixing of one number PVC insulated and PVC sheathed /XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Meter

Meter

Providing , laying and fixing of following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep) and re-filling etc as required.

Meter

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel at least 2 mm thick, vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supply, Installation, testing and commissioning of silent type DG set comprising with diesel engine water cooled , synchonous alternator , AMF panel three phase , acoustic enclosure, battery with charger and related accessories, including PCC 1:2:4 platform, incoming cable 10 meter, earthing GI/CU plate 2 nos. including exhaust pipe B class with insulation as per CPCB IV+ norms etc as required. Make:- Kirloskar/ Ashok Leyland/Cummins.

Providing and laying in position reinforced cement concrete 1: 2: 4 (1 : cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc. as required. (excluding reinforcement) (5.2mx2.42mx1.5m)

VRV INDOOR UNITS

VRF/VRV indoor AC unit (high static ductable) :-Supply, installation, testing and commissioning of high static ductable type comprising of copper evaporator, electronic expansion valve, blower, motor, filter pad, with inbuilt drain pump including internal wiring, controls with cordless remote.(Single phase/three phase)

VRV COMPATIABLE AIR HANDLING UNITS WITH MIXING BOX

14000 CFM,33 TR, TSP 80mmWg

SITC OF Y JOINT FOR Outdoor & Indoor unit As per Suitable size

Copper piping:

Drain Piping

Control Cable

Refrigerant Gas

Site Fabricated GSS Duct

Thermal Insulation

Accoustic Insulation

SITC of MS Fabricated 5 pin DMX Signal OUT Junction box fitted with 5 pin DMX female plug made up of 22SWG CRCA, black epoxy polyester powder coated - MS Signal junction box made up of 22SWG CRCA sheet of undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. 5 pin XLR DMX OUT (Female plug) of reputed make connector, Extra high temperature resistant insulator material, All metal housing offers best overall RF protection & electromagnetic shielding, New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination, Optional connection to easily join pin 1 to chassis ground. CE certified FC/PG 7 cable entry gland, Junction Box must be compact of 125 x 112 x 50mm or less Pipe clamp arrangement for fixingor Raul plug arrangement for wall/floor fixing (Make: Canara Lighting/ Daylight / Pratik Lighting/ Pro Acoustics Solution)/Equivalent

SITC of MS Fabricated 5 pin DMX Signal IN Junction box fitted with 5 pin DMX male plug made up of 22SWG CRCA, black epoxy polyester powder coated - MS Signal junction box made up of 22SWG CRCA sheet of undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish. 5 pin XLR DMX IN (Male plug) of reputed make connector, Extra high temperature resistant insulator material, All metal housing offers best overall RF protection & electromagnetic shielding, New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination, Optional connection to easily join pin 1 to chassis ground. CE certified FC/PG 7 cable entry gland, Junction Box must be compact of 125 x 112 x 50mm or less Pipe clamp arrangement for fixingor Raul plug arrangement for wall/floor fixing (Approved Make: Canara Lighting/ Daylight / Pratik Lighting/ Pro Acoustics Solution)/Equivalent

SITC of CE Certified RDM Enabled 1 universe 512 channel, 48 Fixture Control DMX Lighting Console for RDM/DMX network with LCD screen for easy navigation - 512 or 1024Channels 48 individual fixture control 3 or more encoder wheels LCD Display Support RDM &Art net (Approved Make: Canara Lighting/ Daylight / Pratik Lighting/ Pro Acoustics Solution)/Equivalent

SITC of MS Fabricated Combined 1 Way Motor Control Center Panel with Remote control panel for light bars duly epoxy polyester powder coated - 16A TP or TPN Incomer. TP/TPN R, Y, B Indicator Lamp Volt Meter to read the incoming voltage of each phase. Main Contactor of 9A 240V 4 pole contactor with 04 -06A Over Load relay for safety 24V 4 pole Low Voltage Contactors for each motor outgoing 24V 4 pole Low Voltage Master Up & Down Contactors 240V / 24 V Step-down transformer for Low voltage Contactors Terminal Fuse connectors for each output as additional safety. CE certified Nylon FC/PG 13.5 glands for outgoing cables as per requirements 7/8" or Higher size Brass gland for incoming cable connector with each line having L1, L2, L3, E, 6 , 2 , 4 Indication for each line incoming and outgoing cable connectors (L1, L2, L3, E for Power supply & 6 , 2 , 4 for Limit Switch connection) Panel Including wiringwith proper earthing. Panel with Hingeable door with 2 Nos key door lock complete. Grid mount fixing arrangement for fixing on grid or Anchor fastener for wall/floor fixing (Approved Make: Canara Lighting/ Daylight / Pratik Lighting/ Pro Acoustics Solution)/Equivalent

Supplying and drawing of UTP 4 pair CAT-6 LAN cable in the existing surface/recessed steel /PVC concuitas required. Make - Dlink/Legrand/Molex

SITC OF PVC Conduit 25 mm isi mark

SITC of Category 6 UTP Patch Cords - 1 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact. Dlink/Legrand/Molex

SITC of Category 6 UTP Patch Cords - 2 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact. Dlink/Legrand/Molex

SITC of 24-port GbE Smart Managed Switch with GbE Uplink Interfaces-24 Ports 10/100/1000Mbps+4 SFP;Port Standards & Functions-IEEE 802.3 10BASE-T Ethernet (twisted-pair copper),IEEE 802.3u 100BASE-TX Fast Ethernet (twisted-pair copper),IEEE 802.3ab 1000BASE-T Gigabit Ethernet (twisted- pair copper),IEEE 802.3az compliance Auto-negotiation,IEEE 802.3x Flow Control; Full/Half Duplex-Full/half duplex for 10/100 Mbps speeds,Full duplex for Gigabit speed;Media Interface Exchange Auto MDI/MDIX adjustment for all twisted-pair ports;Switching Capacity 56 Gbps; Transmission Method Store-and-forward; MAC Address Table 16,000 entries per device, Maximum 64 bytes packet forwarding rate 41.7 Mpps,Packet Buffer Memory 1.5 MB,Maximum Power Consumption 22.45 watts, Standby Power Consumption 17.84 W/240 V,Diagnostic LEDs Link/Activity/Speed (Per 10/100/1000 Mbps port), Certifications CE (LVD) BSMICCC, C-Tick. Netgear / D-link/ Cisco.

SITC of Category 6, UTP 24-Port Patch Panel Size - 482.6mm x 44.2 (19’’ x 1U), Panel Material - Steel-fully powder coated, Unshielded - RJ 45, Plug Insertion Cycle - 750 times DC Resistance- 72Ω max, Voltage Rating - 72 Vdc max, Current Rating - 1.5A max. Dlink/Legrand/Molex

Supply fitting fixing Rack 19" 12U fully powder coated complete etc as required with complete accessories (5 amp x 6 socket, wire manager, rack fan) VALRACK/ Netrack make.

Supplying and fixing of RJ 45 computer socket suitable for Cat 6 on module GI box along with base & cover plate in surface or in recess including making connection, soldering etc. as required. Dlink/Legrand/Molex

SITC of Wireless N Access Point Wi-Fi 6 AX1800, up to 1.8 Gbps1 Dual-band, 2x2 MIMO, band-steering & airtime fairness Free-to-download Nuclias Connect software & app Flexible installation with PoE Customisable captive portal Make - TPlink/Cisco/Dlink

16-Port Gigabit Smart Managed PoE Switch 16 x 10/100/1000BASE-T PoE ports 2 x Gigabit RJ45/SFP Combo ports Advanced L2 switching and security features L2+ Static Routing Optional “standard mode” or “surveillance mode” management user interface 193 W PoE budget. Make - TPlink/Cisco/Dlink

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mana/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/Gl structure of suitable strength with following components complete as required:a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years.b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency.c) Data Monitoring System complete with accessories.d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required.e) Lightning and surge voltage protection.f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required.

FIRE SUPPPRESSION SYSTEM

SITC of 5.0 LB Novec 1230/FK-5-1-12

SITC lienear pneumatic heat Detection.

SITC of Master control unit for controlling each system, complete with pressure switches, buzzers and electronic hooter, including all necessary accessories + electrical wiring to make entire system functional (Make :- Fireterx/tracefire/Safefire).

Rubber mat of 16 mm thik and 1000mm wide to with stand 15kv dielectric strength as per is 5424.1969

Shock treatment chart in English and local language duly framed with glass.

First aid box complete with all standard first aid materials.

Rubber gloves 11 KV grade as per IS 4770-68

EARTHING

Supplying and laying 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode, including connection with G.I. nut, bolt, spring, washer excavation and refilling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.